Add Support for MMC/SD in J721e
Subsystems (2)
v2 cover Add Support for MMC/SD in J721e
The following patches add support for MMC/SD in J721e. Currently, SD card is capped at 25 MBps and eMMC is capped at 50 MBps. Support for higher speeds and eMMC boot support will be added in futures series.
v2:
1. Dropped FAT_WRITE patch because its already merged.
2. Fixed up environment patch to support latest CONFIGS.
3. Rebased to the latest u-boot-ti next branch
Faiz Abbas (7):
mmc: am654_sdhci: Get Xin clock by name
mmc: am654_sdhci: Add Support for configuring PHY in J721e
arm: dts: k3-j721e-common-proc-board: Remove voltage-ranges from sdhci
nodes
arm: dts: k3-j721e-common-proc-board: Add pinmux for SD card
configs: j721e_evm: Add configs for ADMA Support
configs: j721e_evm_a72: Add Support for GPT partitions
configs: j721e_evm: Add configs for environment in eMMC
arch/arm/dts/k3-am654-base-board-u-boot.dtsi | 3 +- .../k3-j721e-common-proc-board-u-boot.dtsi | 4 + arch/arm/dts/k3-j721e-common-proc-board.dts | 22 ++- .../arm/dts/k3-j721e-r5-common-proc-board.dts | 16 +++ configs/j721e_evm_a72_defconfig | 9 +- configs/j721e_evm_r5_defconfig | 7 +- drivers/mmc/am654_sdhci.c | 129 ++++++++++++++---- include/configs/j721e_evm.h | 12 ++ 8 files changed, 166 insertions(+), 36 deletions(-)
Signature · 1 line
2.19.2
PATCH v2 1/7 mmc: am654_sdhci: Get Xin clock by name
Get clk_xin by name instead of by index to avoid having to put clocks in the same order in all devices.
--- arch/arm/dts/k3-am654-base-board-u-boot.dtsi | 3 ++- drivers/mmc/am654_sdhci.c | 2 +- 2 files changed, 3 insertions(+), 2 deletions(-)
arch/arm/dts/k3-am654-base-board-u-boot.dtsi +2 -1
@@ -25,7 +25,8 @@ compatible = "ti,am654-sdhci-5.1"; reg = <0x0 0x4FA0000 0x0 0x1000>, <0x0 0x4FB0000 0x0 0x400>; - clocks = <&k3_clks 48 1>; + clocks =<&k3_clks 48 0>, <&k3_clks 48 1>; + clock-names = "clk_ahb", "clk_xin"; power-domains = <&k3_pds 48 TI_SCI_PD_EXCLUSIVE>; max-frequency = <25000000>; ti,otap-del-sel = <0x2>;
drivers/mmc/am654_sdhci.c +1 -1
@@ -223,7 +223,7 @@ static int am654_sdhci_probe(struct udevice *dev)unsigned long clock;int ret; - ret =clk_get_by_index (dev,0 , &clk); + ret =clk_get_by_name (dev,"clk_xin" , &clk);if (ret) {dev_err (dev,"failed to get clock\n" );return ret;
Signature · 1 line
2.19.2
PATCH v2 2/7 mmc: am654_sdhci: Add Support for configuring PHY in J721e
In reply to Faiz AbbasAdd Support for writing to PHY registers for J721e. There are number of differences between the J721e 8 bit PHY, J721e 4 bit PHY and AM654 PHY. Create a driver_data structure with an ops and flags field and use the flags field to indicate these differences. The differences are as follows:
1. The J721e 4 bit instance PHY does not have a DLL. Introduce a DLL_PRESENT flag to make sure that DLL related registers are accessed only where they are present. Also add a separate set_ios_post() callback.
2. The J721e 8 bit instance is not muxed with anything else inside the SoC and hence the IOMUX_ENABLE filed does not exist. Add a flag which is used to indicate the presence of this field.
3. The register field used to select DLL frequency is 3 bit wide in J721e as compared to 2 bits in AM65x. Add another flag that distinguishes these fields.
4. The strobe select field is 8 bit wide as compared to 4 bit wide for AM65x. Add yet another flag to indicate this difference. Strobe select is used only for HS400 speed mode, support for which has not been added in AM65x.
--- drivers/mmc/am654_sdhci.c | 127 +++++++++++++++++++++++++++++--------- 1 file changed, 98 insertions(+), 29 deletions(-)
drivers/mmc/am654_sdhci.c +98 -29
@@ -36,11 +36,14 @@#define OTAPDLYSEL_SHIFT 12#define OTAPDLYSEL_MASK GENMASK(15, 12)#define STRBSEL_SHIFT 24 -#define STRBSEL_MASK GENMASK(27, 24) +#define STRBSEL_4BIT_MASK GENMASK(27, 24) +#define STRBSEL_8BIT_MASK GENMASK(31, 24)#define SEL50_SHIFT 8#define SEL50_MASK BIT(SEL50_SHIFT)#define SEL100_SHIFT 9#define SEL100_MASK BIT(SEL100_SHIFT) +#define FREQSEL_SHIFT 8 +#define FREQSEL_MASK GENMASK(10, 8)#define DLL_TRIM_ICP_SHIFT 4#define DLL_TRIM_ICP_MASK GENMASK(7, 4)#define DR_TY_SHIFT 20
@@ -72,11 +75,20 @@ struct am654_sdhci_plat {u32 otap_del_sel;u32 trm_icp;u32 drv_strength; +u32 strb_sel;u32 flags;#define DLL_PRESENT (1 << 0) +#define IOMUX_PRESENT (1 << 1) +#define FREQSEL_2_BIT (1 << 2) +#define STRBSEL_4_BIT (1 << 3)bool dll_on; }; +struct am654_driver_data { +const struct sdhci_ops *ops; +u32 flags; +}; +static void am654_sdhci_set_control_reg (struct sdhci_host *host) {struct mmc *mmc = (struct mmc *)host->mmc;
@@ -97,7 +109,7 @@ static int am654_sdhci_set_ios_post(struct sdhci_host *host)struct udevice *dev = host->mmc->dev;struct am654_sdhci_plat *plat =dev_get_platdata (dev);unsigned int speed = host->mmc->clock; -int sel50, sel100; +int sel50, sel100, freqsel;u32 mask, val;int ret;
@@ -121,25 +133,49 @@ static int am654_sdhci_set_ios_post(struct sdhci_host *host) mask =OTAPDLYENA_MASK |OTAPDLYSEL_MASK ; val = (1 <<OTAPDLYENA_SHIFT ) | (plat->otap_del_sel <<OTAPDLYSEL_SHIFT ); -regmap_update_bits (plat->base,PHY_CTRL4 , mask, val); -switch (speed) { -case 200000000 : - sel50 =0 ; - sel100 =0 ; -break ; -case 100000000 : - sel50 =0 ; - sel100 =1 ; -break ; -default : - sel50 =1 ; - sel100 =0 ; + +/* Write to STRBSEL for HS400 speed mode */ +if (host->mmc->selected_mode ==MMC_HS_400 ) { +if (plat->flags &STRBSEL_4_BIT ) + mask |=STRBSEL_4BIT_MASK ; +else + mask |=STRBSEL_8BIT_MASK ; + + val |= plat->strb_sel <<STRBSEL_SHIFT ; } -/* Configure PHY DLL frequency */ - mask =SEL50_MASK |SEL100_MASK ; - val = (sel50 <<SEL50_SHIFT ) | (sel100 <<SEL100_SHIFT ); -regmap_update_bits (plat->base,PHY_CTRL5 , mask, val); +regmap_update_bits (plat->base,PHY_CTRL4 , mask, val); + +if (plat->flags &FREQSEL_2_BIT ) { +switch (speed) { +case 200000000 : + sel50 =0 ; + sel100 =0 ; +break ; +case 100000000 : + sel50 =0 ; + sel100 =1 ; +break ; +default : + sel50 =1 ; + sel100 =0 ; + } + +/* Configure PHY DLL frequency */ + mask =SEL50_MASK |SEL100_MASK ; + val = (sel50 <<SEL50_SHIFT ) | (sel100 <<SEL100_SHIFT ); +regmap_update_bits (plat->base,PHY_CTRL5 , mask, val); + }else { +switch (speed) { +case 200000000 : + freqsel =0x0 ; +break ; +default : + freqsel =0x4 ; + } +regmap_update_bits (plat->base,PHY_CTRL5 ,FREQSEL_MASK , + freqsel <<FREQSEL_SHIFT ); + }/* Enable DLL */ regmap_update_bits(plat->base, PHY_CTRL1, ENDLL_MASK,
@@ -164,8 +200,37 @@ const struct sdhci_ops am654_sdhci_ops = { .set_control_reg = &am654_sdhci_set_control_reg, }; +const struct am654_driver_data am654_drv_data = { + .ops = &am654_sdhci_ops, + .flags =IOMUX_PRESENT |FREQSEL_2_BIT |DLL_PRESENT |STRBSEL_4_BIT , +}; + +const struct am654_driver_data j721e_8bit_drv_data = { + .ops = &am654_sdhci_ops, + .flags =DLL_PRESENT , +}; + +static int j721e_4bit_sdhci_set_ios_post (struct sdhci_host *host) +{ +struct udevice *dev = host->mmc->dev; +struct am654_sdhci_plat *plat =dev_get_platdata (dev); +u32 mask, val; + + mask =OTAPDLYENA_MASK |OTAPDLYSEL_MASK ; + val = (1 <<OTAPDLYENA_SHIFT ) | + (plat->otap_del_sel <<OTAPDLYSEL_SHIFT ); +regmap_update_bits (plat->base,PHY_CTRL4 , mask, val); + +return 0 ; +} +const struct sdhci_ops j721e_4bit_sdhci_ops = { - .set_control_reg = &am654_sdhci_set_control_reg, + .set_ios_post = &j721e_4bit_sdhci_set_ios_post, +}; + +const struct am654_driver_data j721e_4bit_drv_data = { + .ops = &j721e_4bit_sdhci_ops, + .flags =IOMUX_PRESENT , };int am654_sdhci_init (struct am654_sdhci_plat *plat)
@@ -202,7 +267,8 @@ int am654_sdhci_init(struct am654_sdhci_plat *plat) }/* Enable pins by setting IO mux to 0 */ -regmap_update_bits (plat->base,PHY_CTRL1 ,IOMUX_ENABLE_MASK ,0 ); +if (plat->flags &IOMUX_PRESENT ) +regmap_update_bits (plat->base,PHY_CTRL1 ,IOMUX_ENABLE_MASK ,0 );/* Set slot type based on SD or eMMC */ if (plat->non_removable)
@@ -215,6 +281,8 @@ int am654_sdhci_init(struct am654_sdhci_plat *plat)static int am654_sdhci_probe (struct udevice *dev) { +struct am654_driver_data *drv_data = + (struct am654_driver_data *)dev_get_driver_data (dev);struct am654_sdhci_plat *plat =dev_get_platdata (dev);struct mmc_uclass_priv *upriv =dev_get_uclass_priv (dev);struct sdhci_host *host =dev_get_priv (dev);
@@ -242,7 +310,8 @@ static int am654_sdhci_probe(struct udevice *dev) AM654_SDHCI_MIN_FREQ);if (ret)return ret; - host->ops = (struct sdhci_ops *)dev_get_driver_data (dev); + + host->ops = drv_data->ops; host->mmc->priv = host; upriv->mmc = host->mmc;
@@ -265,10 +334,6 @@ static int am654_sdhci_ofdata_to_platdata(struct udevice *dev) host->ioaddr = (void *)dev_read_addr (dev); plat->non_removable =dev_read_bool (dev,"non-removable" ); -if (device_is_compatible (dev,"ti,am654-sdhci-5.1" ) || -device_is_compatible (dev,"ti,j721e-sdhci-8bit" )) - plat->flags |=DLL_PRESENT ; - ret =dev_read_u32 (dev,"ti,otap-del-sel" , &plat->otap_del_sel);if (ret)return ret;
@@ -314,23 +379,27 @@ static int am654_sdhci_ofdata_to_platdata(struct udevice *dev)static int am654_sdhci_bind (struct udevice *dev) { +struct am654_driver_data *drv_data = + (struct am654_driver_data *)dev_get_driver_data (dev);struct am654_sdhci_plat *plat =dev_get_platdata (dev); + plat->flags = drv_data->flags; +return sdhci_bind (dev, &plat->mmc, &plat->cfg); }static const struct udevice_id am654_sdhci_ids[] = { { .compatible ="ti,am654-sdhci-5.1" , - .data = (ulong)&am654_sdhci_ops, + .data = (ulong)&am654_drv_data, }, { .compatible ="ti,j721e-sdhci-8bit" , - .data = (ulong)&am654_sdhci_ops, + .data = (ulong)&j721e_8bit_drv_data, }, { .compatible ="ti,j721e-sdhci-4bit" , - .data = (ulong)&j721e_4bit_sdhci_ops, + .data = (ulong)&j721e_4bit_drv_data, }, { } };
Signature · 1 line
2.19.2
PATCH v2 3/7 arm: dts: k3-j721e-common-proc-board: Remove voltage-ranges from sdhci nodes
In reply to Faiz Abbasvoltage-ranges properties are NOP. Remove them.
--- arch/arm/dts/k3-j721e-common-proc-board.dts | 2 -- 1 file changed, 2 deletions(-)
arch/arm/dts/k3-j721e-common-proc-board.dts +0 -2
@@ -67,14 +67,12 @@ &main_sdhci0 { /* eMMC */ - voltage-ranges = <1800 1800>; non-removable; ti,driver-strength-ohm = <50>; }; &main_sdhci1 { /* SD/MMC */ - voltage-ranges = <1800 1800 3300 3300>; ti,driver-strength-ohm = <50>; };
Signature · 1 line
2.19.2
PATCH v2 4/7 arm: dts: k3-j721e-common-proc-board: Add pinmux for SD card
In reply to Faiz AbbasAdd pinmux for sdhci1 node connected to the SD card.
--- .../k3-j721e-common-proc-board-u-boot.dtsi | 4 ++++ arch/arm/dts/k3-j721e-common-proc-board.dts | 20 ++++++++++++++++++- .../arm/dts/k3-j721e-r5-common-proc-board.dts | 16 +++++++++++++++ 3 files changed, 39 insertions(+), 1 deletion(-)
arch/arm/dts/k3-j721e-common-proc-board-u-boot.dtsi +4 -0
@@ -325,3 +325,7 @@ reg-names = "gmii-sel"; }; }; + +&main_mmc1_pins_default { + u-boot,dm-spl; +};
arch/arm/dts/k3-j721e-common-proc-board.dts +19 -1
@@ -65,6 +65,22 @@ status = "disabled"; }; +&main_pmx0 { + main_mmc1_pins_default: main_mmc1_pins_default { + pinctrl-single,pins = < + J721E_IOPAD(0x254, PIN_INPUT, 0) /* (R29) MMC1_CMD */ + J721E_IOPAD(0x250, PIN_INPUT, 0) /* (P25) MMC1_CLK */ + J721E_IOPAD(0x2ac, PIN_INPUT, 0) /* (P25) MMC1_CLKLB */ + J721E_IOPAD(0x24c, PIN_INPUT, 0) /* (R24) MMC1_DAT0 */ + J721E_IOPAD(0x248, PIN_INPUT, 0) /* (P24) MMC1_DAT1 */ + J721E_IOPAD(0x244, PIN_INPUT, 0) /* (R25) MMC1_DAT2 */ + J721E_IOPAD(0x240, PIN_INPUT, 0) /* (R26) MMC1_DAT3 */ + J721E_IOPAD(0x258, PIN_INPUT, 0) /* (P23) MMC1_SDCD */ + J721E_IOPAD(0x25c, PIN_INPUT, 0) /* (R28) MMC1_SDWP */ + >; + }; +}; + &main_sdhci0 { /* eMMC */ non-removable;
@@ -72,7 +88,9 @@ }; &main_sdhci1 { - /* SD/MMC */ + /* SD card */ + pinctrl-names = "default"; + pinctrl-0 = <&main_mmc1_pins_default>; ti,driver-strength-ohm = <50>; };
arch/arm/dts/k3-j721e-r5-common-proc-board.dts +16 -0
@@ -119,6 +119,20 @@ J721E_IOPAD(0x210, PIN_INPUT, 7) /* (W3) MCAN1_RX.GPIO1_3 */ >; }; + + main_mmc1_pins_default: main_mmc1_pins_default { + pinctrl-single,pins = < + J721E_IOPAD(0x254, PIN_INPUT, 0) /* (R29) MMC1_CMD */ + J721E_IOPAD(0x250, PIN_INPUT, 0) /* (P25) MMC1_CLK */ + J721E_IOPAD(0x2ac, PIN_INPUT, 0) /* (P25) MMC1_CLKLB */ + J721E_IOPAD(0x24c, PIN_INPUT, 0) /* (R24) MMC1_DAT0 */ + J721E_IOPAD(0x248, PIN_INPUT, 0) /* (P24) MMC1_DAT1 */ + J721E_IOPAD(0x244, PIN_INPUT, 0) /* (R25) MMC1_DAT2 */ + J721E_IOPAD(0x240, PIN_INPUT, 0) /* (R26) MMC1_DAT3 */ + J721E_IOPAD(0x258, PIN_INPUT, 0) /* (P23) MMC1_SDCD */ + J721E_IOPAD(0x25c, PIN_INPUT, 0) /* (R28) MMC1_SDWP */ + >; + }; }; &wkup_uart0 {
@@ -156,6 +170,8 @@ /delete-property/ power-domains; /delete-property/ assigned-clocks; /delete-property/ assigned-clock-parents; + pinctrl-names = "default"; + pinctrl-0 = <&main_mmc1_pins_default>; clock-names = "clk_xin"; clocks = <&clk_200mhz>; ti,driver-strength-ohm = <50>;
Signature · 1 line
2.19.2
PATCH v2 5/7 configs: j721e_evm: Add configs for ADMA Support
In reply to Faiz AbbasAdd configs for ADMA Support.
--- configs/j721e_evm_a72_defconfig | 2 ++ configs/j721e_evm_r5_defconfig | 1 + 2 files changed, 3 insertions(+)
configs/j721e_evm_a72_defconfig +2 -0
@@ -83,6 +83,8 @@ CONFIG_K3_SEC_PROXY=y CONFIG_MISC=y CONFIG_DM_MMC=y CONFIG_MMC_SDHCI=y +CONFIG_MMC_SDHCI_ADMA=y +CONFIG_SPL_MMC_SDHCI_ADMA=y CONFIG_MMC_SDHCI_AM654=y CONFIG_MTD=y CONFIG_DM_MTD=y
configs/j721e_evm_r5_defconfig +1 -0
@@ -69,6 +69,7 @@ CONFIG_FS_LOADER=y CONFIG_K3_AVS0=y CONFIG_DM_MMC=y CONFIG_MMC_SDHCI=y +CONFIG_SPL_MMC_SDHCI_ADMA=y CONFIG_MMC_SDHCI_AM654=y CONFIG_MTD=y CONFIG_DM_SPI_FLASH=y
Signature · 1 line
2.19.2
PATCH v2 6/7 configs: j721e_evm_a72: Add Support for GPT partitions
In reply to Faiz AbbasIntroduce a default GPT partition table for eMMC.
--- include/configs/j721e_evm.h | 6 ++++++ 1 file changed, 6 insertions(+)
include/configs/j721e_evm.h +6 -0
@@ -71,6 +71,11 @@"args_all=setenv optargs earlycon=ns16550a,mmio32,0x02800000\0" \ "run_kern=booti ${loadaddr} ${rd_spec} ${fdtaddr}\0" +#define PARTS_DEFAULT \ +/* Linux partitions */ \ + "uuid_disk=${uuid_gpt_disk};" \ + "name=rootfs,start=0,size=-,uuid=${uuid_gpt_rootfs}\0" +/* U-Boot MMC-specific configuration */ #define EXTRA_ENV_J721E_BOARD_SETTINGS_MMC \ "boot=mmc\0" \
@@ -88,6 +93,7 @@"load mmc ${bootpart} ${overlayaddr} ${bootdir}/${overlay} && " \"fdt apply ${overlayaddr};" \"done;\0" \ +"partitions=" PARTS_DEFAULT \"get_kern_mmc=load mmc ${bootpart} ${loadaddr} " \"${bootdir}/${name_kern}\0"
Signature · 1 line
2.19.2
PATCH v2 7/7 configs: j721e_evm: Add configs for environment in eMMC
In reply to Faiz AbbasAdd config to save and read back environment from eMMC.
--- configs/j721e_evm_a72_defconfig | 7 ++++++- configs/j721e_evm_r5_defconfig | 6 +++++- include/configs/j721e_evm.h | 6 ++++++ 3 files changed, 17 insertions(+), 2 deletions(-)
configs/j721e_evm_a72_defconfig +6 -1
@@ -5,10 +5,11 @@ CONFIG_SPL_LIBGENERIC_SUPPORT=y CONFIG_SYS_MALLOC_F_LEN=0x8000 CONFIG_SOC_K3_J721E=y CONFIG_TARGET_J721E_A72_EVM=y +CONFIG_ENV_SIZE=0x20000 +CONFIG_ENV_OFFSET=0x680000 CONFIG_SPL_MMC_SUPPORT=y CONFIG_SPL_SERIAL_SUPPORT=y CONFIG_SPL_DRIVERS_MISC_SUPPORT=y -CONFIG_ENV_SIZE=0x20000 CONFIG_SPL_STACK_R_ADDR=0x82000000 CONFIG_NR_DRAM_BANKS=2 CONFIG_SPL_FS_FAT=y
@@ -24,6 +25,7 @@ CONFIG_BOOTCOMMAND="run findfdt; run envboot; run init_${boot}; run boot_rprocs; CONFIG_SPL_SYS_MALLOC_SIMPLE=y CONFIG_SPL_STACK_R=y CONFIG_SPL_SEPARATE_BSS=y +CONFIG_SPL_ENV_SUPPORT=y CONFIG_SPL_I2C_SUPPORT=y CONFIG_SPL_DM_MAILBOX=y CONFIG_SPL_DM_RESET=y
@@ -54,6 +56,9 @@ CONFIG_SPL_OF_CONTROL=y CONFIG_DEFAULT_DEVICE_TREE="k3-j721e-common-proc-board" CONFIG_SPL_MULTI_DTB_FIT=y CONFIG_SPL_MULTI_DTB_FIT_NO_COMPRESSION=y +CONFIG_ENV_IS_IN_MMC=y +CONFIG_SYS_REDUNDAND_ENVIRONMENT=y +CONFIG_ENV_OFFSET_REDUND=0x700000 CONFIG_SYS_RELOC_GD_ENV_ADDR=y CONFIG_NET_RANDOM_ETHADDR=y CONFIG_DM=y
configs/j721e_evm_r5_defconfig +5 -1
@@ -6,10 +6,11 @@ CONFIG_SPL_LIBGENERIC_SUPPORT=y CONFIG_SYS_MALLOC_F_LEN=0x55000 CONFIG_SOC_K3_J721E=y CONFIG_TARGET_J721E_R5_EVM=y +CONFIG_ENV_SIZE=0x20000 +CONFIG_ENV_OFFSET=0x680000 CONFIG_SPL_MMC_SUPPORT=y CONFIG_SPL_SERIAL_SUPPORT=y CONFIG_SPL_DRIVERS_MISC_SUPPORT=y -CONFIG_ENV_SIZE=0x20000 CONFIG_SPL_STACK_R_ADDR=0x82000000 CONFIG_SPL_FS_FAT=y CONFIG_SPL_LIBDISK_SUPPORT=y
@@ -46,6 +47,9 @@ CONFIG_CMD_FAT=y CONFIG_OF_CONTROL=y CONFIG_SPL_OF_CONTROL=y CONFIG_DEFAULT_DEVICE_TREE="k3-j721e-r5-common-proc-board" +CONFIG_ENV_IS_IN_MMC=y +CONFIG_SYS_REDUNDAND_ENVIRONMENT=y +CONFIG_ENV_OFFSET_REDUND=0x700000 CONFIG_SYS_RELOC_GD_ENV_ADDR=y CONFIG_DM=y CONFIG_SPL_DM=y
include/configs/j721e_evm.h +6 -0
@@ -127,4 +127,10 @@/* Now for the remaining common defines */ #include <configs/ti_armv7_common.h> +/* MMC ENV related defines */ +#ifdef CONFIG_ENV_IS_IN_MMC +#define CONFIG_SYS_MMC_ENV_DEV 0 +#define CONFIG_SYS_MMC_ENV_PART 1 +#endif +#endif /* __CONFIG_J721E_EVM_H */
Signature · 1 line
2.19.2
v2 cover Add Support for MMC/SD in J721e
In reply to Faiz AbbasQuoted 8 lines · Faiz Abbas
The following patches add support for MMC/SD in J721e. Currently, SD card is capped at 25 MBps and eMMC is capped at 50 MBps. Support for higher speeds and eMMC boot support will be added in futures series.
v2:
1. DroppedFAT_WRITEpatch because its already merged.
2. Fixed up environment patch to support latest CONFIGS.
3. Rebased to the latest u-boot-ti next branch
Merged into u-boot-ti
Thanks and regards,
Lokesh
Quoted 21 lines
Faiz Abbas (7):
mmc:am654_sdhci: Get Xin clock by name
mmc:am654_sdhci: Add Support for configuring PHY in J721e
arm: dts: k3-j721e-common-proc-board: Remove voltage-ranges from sdhci
nodes
arm: dts: k3-j721e-common-proc-board: Add pinmux for SD card
configs:j721e_evm: Add configs for ADMA Support
configs:j721e_evm_a72: Add Support for GPT partitions
configs:j721e_evm: Add configs for environment in eMMCarch/arm/dts/k3-am654-base-board-u-boot.dtsi | 3 +- .../k3-j721e-common-proc-board-u-boot.dtsi | 4 + arch/arm/dts/k3-j721e-common-proc-board.dts | 22 ++- .../arm/dts/k3-j721e-r5-common-proc-board.dts | 16 +++ configs/j721e_evm_a72_defconfig | 9 +- configs/j721e_evm_r5_defconfig | 7 +- drivers/mmc/am654_sdhci.c | 129 ++++++++++++++---- include/configs/j721e_evm.h | 12 ++ 8 files changed, 166 insertions(+), 36 deletions(-)