Skip to contentSkip to conversation

hw/intc/arm_gicv3_kvm: Stop wrongly programming GICR_PENDBASER.PTZ bit

PATCH Applied Zenghui Yu 2 participants 2 messages Jan 19, 2020 – Jan 30, 2020 KVM arm64

lore
Share & tools
lore

Zenghui Yu

author reviewer
#0 lore raw

PATCH 1/1 hw/intc/arm_gicv3_kvm: Stop wrongly programming GICR_PENDBASER.PTZ bit

If LPIs are disabled, KVM will just ignore the GICR_PENDBASER.PTZ bit when restoring GICR_CTLR. Setting PTZ here makes littlt sense in "reduce GIC initialization time".

And what's worse, PTZ is generally programmed by guest to indicate to the Redistributor whether the LPI Pending table is zero when enabling LPIs. If migration is triggered when the PTZ has just been cleared by guest (and before enabling LPIs), we will see PTZ==1 on the destination side, which is not as expected. Let's just drop this hackish userspace behavior.

Also take this chance to refine the comment a bit.

Fixes 367b9f527bec ("hw/intc/arm_gicv3_kvm: Implement get/put functions")
---
 hw/intc/arm_gicv3_kvm.c | 11 ++++-------
 1 file changed, 4 insertions(+), 7 deletions(-)
hw/intc/arm_gicv3_kvm.c +4 -7
index 9c7f4ab871..49304ca589 100644
@@ -336,7 +336,10 @@ static void kvm_arm_gicv3_put(GICv3State *s)
     kvm_gicd_access(s, GICD_CTLR, &reg, true);
 
     if (redist_typer & GICR_TYPER_PLPIS) {
-        /* Set base addresses before LPIs are enabled by GICR_CTLR write */
+        /*
+         * Restore base addresses before LPIs are potentially enabled by
+         * GICR_CTLR write
+         */
         for (ncpu = 0; ncpu < s->num_cpu; ncpu++) {
             GICv3CPUState *c = &s->cpu[ncpu];
 
@@ -347,12 +350,6 @@ static void kvm_arm_gicv3_put(GICv3State *s)
             kvm_gicr_access(s, GICR_PROPBASER + 4, ncpu, &regh, true);
 
             reg64 = c->gicr_pendbaser;
-            if (!(c->gicr_ctlr & GICR_CTLR_ENABLE_LPIS)) {
-                /* Setting PTZ is advised if LPIs are disabled, to reduce
-                 * GIC initialization time.
-                 */
-                reg64 |= GICR_PENDBASER_PTZ;
-            }
             regl = (uint32_t)reg64;
             kvm_gicr_access(s, GICR_PENDBASER, ncpu, &regl, true);
             regh = (uint32_t)(reg64 >> 32);
Signature · 7 lines
2.19.1


_______________________________________________
kvmarm mailing list
[email protected]
https://lists.cs.columbia.edu/mailman/listinfo/kvmarm
#1 lore raw
Quoted 5 lines · Zenghui Yu

If LPIs are disabled, KVM will just ignore the GICR_PENDBASER.PTZ bit when restoring GICR_CTLR. Setting PTZ here makes littlt sense in "reduce GIC initialization time".

Quoted 7 lines

And what's worse, PTZ is generally programmed by guest to indicate to the Redistributor whether the LPI Pending table is zero when enabling LPIs. If migration is triggered when the PTZ has just been cleared by guest (and before enabling LPIs), we will see PTZ==1 on the destination side, which is not as expected. Let's just drop this hackish userspace behavior.

Also take this chance to refine the comment a bit.

I pulled up the original code-review discussion where this code was added:
https://lists.gnu.org/archive/html/qemu-devel/2015-10/msg05889.html

It looks like the original reason for adding it was that the GICR_PENDBASER.PTZ bit is write-only, and so there's no way for the migration code in QEMU to accurately restore it on the destination end of a migration. So Pavel picked a heuristic for guessing what the right value of the PTZ bit was.

It sounds like the penalty if userspace sets the bit to 0 always on a migration is not significant, so I guess that just setting this bit to 0 always is an OK thing to do (as you say, there's a window in the existing implementation where we do the wrong thing sometimes if migration happens at the wrong time, because the current code's heuristic can sometimes fail in the wrong direction).

Applied to target-arm.next.

thanks
-- PMM
_______________________________________________
kvmarm mailing list
[email protected]
https://lists.cs.columbia.edu/mailman/listinfo/kvmarm