Skip to contentSkip to conversation

gpiolib: Lower verbosity when allocating hierarchy irq

PATCH In review Kevin Hao 2 participants 2 messages Jan 20, 2020 – Jan 23, 2020 GPIO

lore
Share & tools
lore

Kevin Hao

author
#0 lore raw

PATCH 1/1 gpiolib: Lower verbosity when allocating hierarchy irq

In the current codes, the following 3 lines would be output to
the console for each irq line.
gpio gpiochip0: (gpio_thunderx): allocate IRQ 10, hwirq 0
gpio gpiochip0: (gpio_thunderx): found parent hwirq 245784
gpio gpiochip0: (gpio_thunderx): alloc_irqs_parent for 10 parent hwirq 245784

In general, there are about tens of irq lines for each gpio chip, and then it would emit so many insignificant log in the boot process. These infos are more suitable for the dbg purpose. So change these to the dbg level. With this change, about 200 lines are suppressed on my Marvell cn96xx board.

---
 drivers/gpio/gpiolib.c | 6 +++---
 1 file changed, 3 insertions(+), 3 deletions(-)
drivers/gpio/gpiolib.c +3 -3
index e9f168b276ad..66e66c141fe8 100644
@@ -2006,7 +2006,7 @@ static int gpiochip_hierarchy_irq_domain_alloc(struct irq_domain *d,
 	if (ret)
 		return ret;
 
-	chip_info(gc, "allocate IRQ %d, hwirq %lu\n", irq,  hwirq);
+	chip_dbg(gc, "allocate IRQ %d, hwirq %lu\n", irq,  hwirq);
 
 	ret = girq->child_to_parent_hwirq(gc, hwirq, type,
 					  &parent_hwirq, &parent_type);
@@ -2014,7 +2014,7 @@ static int gpiochip_hierarchy_irq_domain_alloc(struct irq_domain *d,
 		chip_err(gc, "can't look up hwirq %lu\n", hwirq);
 		return ret;
 	}
-	chip_info(gc, "found parent hwirq %u\n", parent_hwirq);
+	chip_dbg(gc, "found parent hwirq %u\n", parent_hwirq);
 
 	/*
 	 * We set handle_bad_irq because the .set_type() should
@@ -2034,7 +2034,7 @@ static int gpiochip_hierarchy_irq_domain_alloc(struct irq_domain *d,
 	if (!parent_arg)
 		return -ENOMEM;
 
-	chip_info(gc, "alloc_irqs_parent for %d parent hwirq %d\n",
+	chip_dbg(gc, "alloc_irqs_parent for %d parent hwirq %d\n",
 		  irq, parent_hwirq);
 	irq_set_lockdep_class(irq, gc->irq.lock_key, gc->irq.request_key);
 	ret = irq_domain_alloc_irqs_parent(d, irq, 1, parent_arg);
Signature · 1 line
2.14.4
#1 lore raw
Quoted 6 lines · Kevin Hao

In the current codes, the following 3 lines would be output to
the console for each irq line.
gpio gpiochip0: (gpio_thunderx): allocate IRQ 10, hwirq 0
gpio gpiochip0: (gpio_thunderx): found parent hwirq 245784
gpio gpiochip0: (gpio_thunderx): alloc_irqs_parent for 10 parent hwirq 245784

Quoted 7 lines

In general, there are about tens of irq lines for each gpio chip, and then it would emit so many insignificant log in the boot process. These infos are more suitable for the dbg purpose. So change these to the dbg level. With this change, about 200 lines are suppressed on my Marvell cn96xx board.

Patch applied, thanks for your hard work on this Kevin!

Yours,
Linus Walleij