Skip to contentSkip to conversation

Add support for Tebibytes

PATCH Applied Kinga Tanska 2 participants 2 messages Jan 21, 2020 MD RAID

lore
Share & tools
lore
#0 lore raw

PATCH v2 1/1 Add support for Tebibytes

Adding support for Tebibytes enables display size of volumes in Tebibytes and Terabytes when they are bigger than 2048 GiB (or GB).

---
 mdadm.8.in | 20 ++++++++++----------
 util.c     | 47 +++++++++++++++++++++++++++++++++--------------
 2 files changed, 43 insertions(+), 24 deletions(-)
mdadm.8.in +10 -10
index 9aec9f4..ad7a0aa 100644
@@ -467,8 +467,8 @@ If this is not specified
 size, though if there is a variance among the drives of greater than 1%, a warning is
 issued.
 
-A suffix of 'K', 'M' or 'G' can be given to indicate Kilobytes, Megabytes or
-Gigabytes respectively.
+A suffix of 'K', 'M', 'G' or 'T' can be given to indicate Kilobytes,
+Megabytes, Gigabytes or Terabytes respectively.
 
 Sometimes a replacement drive can be a little smaller than the
 original drives though this should be minimised by IDEMA standards.
@@ -534,8 +534,8 @@ problems the array can be made bigger again with no loss with another
 .B "\-\-grow \-\-array\-size="
 command.
 
-A suffix of 'K', 'M' or 'G' can be given to indicate Kilobytes, Megabytes or
-Gigabytes respectively.
+A suffix of 'K', 'M', 'G' or 'T' can be given to indicate Kilobytes,
+Megabytes, Gigabytes or Terabytes respectively.
 A value of
 .B max
 restores the apparent size of the array to be whatever the real
@@ -553,8 +553,8 @@ This is only meaningful for RAID0, RAID4, RAID5, RAID6, and RAID10.
 RAID4, RAID5, RAID6, and RAID10 require the chunk size to be a power
 of 2.  In any case it must be a multiple of 4KB.
 
-A suffix of 'K', 'M' or 'G' can be given to indicate Kilobytes, Megabytes or
-Gigabytes respectively.
+A suffix of 'K', 'M', 'G' or 'T' can be given to indicate Kilobytes,
+Megabytes, Gigabytes or Terabytes respectively.
 
 .TP
 .BR \-\-rounding=
@@ -741,8 +741,8 @@ When using an
 bitmap, the chunksize defaults to 64Meg, or larger if necessary to
 fit the bitmap into the available space.
 
-A suffix of 'K', 'M' or 'G' can be given to indicate Kilobytes, Megabytes or
-Gigabytes respectively.
+A suffix of 'K', 'M', 'G' or 'T' can be given to indicate Kilobytes,
+Megabytes, Gigabytes or Terabytes respectively.
 
 .TP
 .BR \-W ", " \-\-write\-mostly
@@ -831,8 +831,8 @@ an array which was originally created using a different version of
 which computed a different offset.
 
 Setting the offset explicitly over-rides the default.  The value given
-is in Kilobytes unless a suffix of 'K', 'M' or 'G' is used to explicitly
-indicate Kilobytes, Megabytes or Gigabytes respectively.
+is in Kilobytes unless a suffix of 'K', 'M', 'G' or 'T' is used to explicitly
+indicate Kilobytes, Megabytes, Gigabytes or Terabytes respectively.
 
 Since Linux 3.4,
 .B \-\-data\-offset
util.c +33 -14

103 lines not on this page · raw message

Signature · 1 line
2.16.4
Applied
#1 lore raw
Quoted 9 lines · Kinga Tanska

Adding support for Tebibytes enables display size of volumes in Tebibytes and Terabytes when they are bigger than 2048 GiB (or GB).

---
 mdadm.8.in | 20 ++++++++++----------
 util.c     | 47 +++++++++++++++++++++++++++++++++--------------
 2 files changed, 43 insertions(+), 24 deletions(-)

Applied!

Thanks,
Jes