board: toradex: add Verdin iMX8MM 2GB WB IT v1.0a
Subsystems (4)
cover board: toradex: add Verdin iMX8MM 2GB WB IT v1.0a
This add initial minimal support for the Toradex Verdin iMX8MM 2GB WB IT V1.0A module. They are now strapped to boot from eFuses which are factory fused to properly boot from their on-module eMMC. U-Boot supports booting from the on-module eMMC only, SDP support is disabled for now.
Functionality wise the following is known to be working:
- eMMC, 8-bit and 4-bit MMC/SD card slots
- Ethernet
- GPIOs
- I2C
Boot sequence is:
SPL ---> ATF (TF-A) ---> U-boot proper
ATF, U-boot proper and u-boot.dtb images are packed into FIT image, loaded by SPL.
Boot:
U-Boot SPL 2020.01-01840-gd92bdc79cf-dirty (Jan 22 2020 - 18:50:57 +0200) Normal Boot
Trying to boot from MMC1
U-Boot 2020.01-01840-gd92bdc79cf-dirty (Jan 22 2020 - 18:50:57 +0200)
CPU: Freescale i.MX8MMQ rev1.0 at 0 MHz Reset cause: POR DRAM: 2 GiB MMC: FSL_SDHC: 0, FSL_SDHC: 1 Loading Environment from MMC... OK In: serial Out: serial Err: serial Model: Toradex Verdin iMX8M Mini 2GB Wi-Fi / BT IT V1.0A, Serial# 06535148 Net: Could not get PHY for FEC0: addr 7 eth0: ethernet at 30be0000 Hit any key to stop autoboot: 0
Igor Opaniuk (3):
board: toradex: add Verdin iMX8MM 2GB WB IT v1.0a
board: toradex: verdin-imx8mm: add README
board: toradex: verdin-imx8mm: add MAINTAINERS
Marcel Ziswiler (1):
toradex: tdx-cfg-block: add Verdin i.MX8MM support
Max Krummenacher (1):
dt-bindings: pinctrl: imx8mm: add alternative uart muxings
arch/arm/dts/Makefile | 3 +- arch/arm/dts/imx8mm-pinfunc.h | 21 + arch/arm/dts/imx8mm-verdin-u-boot.dtsi | 103 ++ arch/arm/dts/imx8mm-verdin.dts | 854 +++++++++ arch/arm/mach-imx/imx8m/Kconfig | 7 + board/toradex/common/tdx-cfg-block.c | 17 +- board/toradex/common/tdx-cfg-block.h | 1 + board/toradex/verdin-imx8mm/Kconfig | 30 + board/toradex/verdin-imx8mm/MAINTAINERS | 9 + board/toradex/verdin-imx8mm/Makefile | 12 + board/toradex/verdin-imx8mm/README | 81 + board/toradex/verdin-imx8mm/imximage.cfg | 16 + board/toradex/verdin-imx8mm/lpddr4_timing.c | 1851 +++++++++++++++++++ board/toradex/verdin-imx8mm/spl.c | 183 ++ board/toradex/verdin-imx8mm/verdin-imx8mm.c | 74 + configs/verdin-imx8mm_defconfig | 88 + include/configs/verdin-imx8mm.h | 121 ++ 17 files changed, 3468 insertions(+), 3 deletions(-) create mode 100644 arch/arm/dts/imx8mm-verdin-u-boot.dtsi create mode 100644 arch/arm/dts/imx8mm-verdin.dts create mode 100644 board/toradex/verdin-imx8mm/Kconfig create mode 100644 board/toradex/verdin-imx8mm/MAINTAINERS create mode 100644 board/toradex/verdin-imx8mm/Makefile create mode 100644 board/toradex/verdin-imx8mm/README create mode 100644 board/toradex/verdin-imx8mm/imximage.cfg create mode 100644 board/toradex/verdin-imx8mm/lpddr4_timing.c create mode 100644 board/toradex/verdin-imx8mm/spl.c create mode 100644 board/toradex/verdin-imx8mm/verdin-imx8mm.c create mode 100644 configs/verdin-imx8mm_defconfig create mode 100644 include/configs/verdin-imx8mm.h
Signature · 1 line
2.17.1
PATCH 1/5 dt-bindings: pinctrl: imx8mm: add alternative uart muxings
From: Max Krummenacher <[email protected]>
Add alternative UART muxing defines.
---
arch/arm/dts/imx8mm-pinfunc.h | 21 +++++++++++++++++++++ 1 file changed, 21 insertions(+)
arch/arm/dts/imx8mm-pinfunc.h +21 -0
@@ -430,18 +430,26 @@#define MX8MM_IOMUXC_SAI1_MCLK_SIM_M_HRESP 0x1AC 0x414 0x000 0x7 0x0#define MX8MM_IOMUXC_SAI2_RXFS_SAI2_RX_SYNC 0x1B0 0x418 0x000 0x0 0x0#define MX8MM_IOMUXC_SAI2_RXFS_SAI5_TX_SYNC 0x1B0 0x418 0x4EC 0x1 0x2 +#define MX8MM_IOMUXC_SAI2_RXFS_UART1_TX 0x1B0 0x418 0x000 0x4 0x0 +#define MX8MM_IOMUXC_SAI2_RXFS_UART1_RX 0x1B0 0x418 0x4F4 0x4 0x2#define MX8MM_IOMUXC_SAI2_RXFS_GPIO4_IO21 0x1B0 0x418 0x000 0x5 0x0#define MX8MM_IOMUXC_SAI2_RXFS_SIM_M_HSIZE0 0x1B0 0x418 0x000 0x7 0x0#define MX8MM_IOMUXC_SAI2_RXC_SAI2_RX_BCLK 0x1B4 0x41C 0x000 0x0 0x0#define MX8MM_IOMUXC_SAI2_RXC_SAI5_TX_BCLK 0x1B4 0x41C 0x4E8 0x1 0x2 +#define MX8MM_IOMUXC_SAI2_RXC_UART1_RX 0x1B4 0x41C 0x4F4 0x4 0x3 +#define MX8MM_IOMUXC_SAI2_RXC_UART1_TX 0x1B4 0x41C 0x000 0x4 0x0#define MX8MM_IOMUXC_SAI2_RXC_GPIO4_IO22 0x1B4 0x41C 0x000 0x5 0x0#define MX8MM_IOMUXC_SAI2_RXC_SIM_M_HSIZE1 0x1B4 0x41C 0x000 0x7 0x0#define MX8MM_IOMUXC_SAI2_RXD0_SAI2_RX_DATA0 0x1B8 0x420 0x000 0x0 0x0#define MX8MM_IOMUXC_SAI2_RXD0_SAI5_TX_DATA0 0x1B8 0x420 0x000 0x1 0x0 +#define MX8MM_IOMUXC_SAI2_RXD0_UART1_RTS_B 0x1B8 0x420 0x4F0 0x4 0x2 +#define MX8MM_IOMUXC_SAI2_RXD0_UART1_CTS_B 0x1B8 0x420 0x000 0x4 0x0#define MX8MM_IOMUXC_SAI2_RXD0_GPIO4_IO23 0x1B8 0x420 0x000 0x5 0x0#define MX8MM_IOMUXC_SAI2_RXD0_SIM_M_HSIZE2 0x1B8 0x420 0x000 0x7 0x0#define MX8MM_IOMUXC_SAI2_TXFS_SAI2_TX_SYNC 0x1BC 0x424 0x000 0x0 0x0#define MX8MM_IOMUXC_SAI2_TXFS_SAI5_TX_DATA1 0x1BC 0x424 0x000 0x1 0x0 +#define MX8MM_IOMUXC_SAI2_TXFS_UART1_CTS_B 0x1BC 0x424 0x000 0x4 0x0 +#define MX8MM_IOMUXC_SAI2_TXFS_UART1_RTS_B 0x1BC 0x424 0x4F0 0x4 0x3#define MX8MM_IOMUXC_SAI2_TXFS_GPIO4_IO24 0x1BC 0x424 0x000 0x5 0x0#define MX8MM_IOMUXC_SAI2_TXFS_SIM_M_HWRITE 0x1BC 0x424 0x000 0x7 0x0#define MX8MM_IOMUXC_SAI2_TXC_SAI2_TX_BCLK 0x1C0 0x428 0x000 0x0 0x0
@@ -464,21 +472,34 @@#define MX8MM_IOMUXC_SAI3_RXC_SAI3_RX_BCLK 0x1D0 0x438 0x000 0x0 0x0#define MX8MM_IOMUXC_SAI3_RXC_GPT1_CAPTURE2 0x1D0 0x438 0x000 0x1 0x0#define MX8MM_IOMUXC_SAI3_RXC_SAI5_RX_BCLK 0x1D0 0x438 0x4D0 0x2 0x2 +#define MX8MM_IOMUXC_SAI3_RXC_UART2_DCE_CTS_B 0x1D0 0x438 0x000 0x1 0x0 +#define MX8MM_IOMUXC_SAI3_RXC_UART2_DCE_RTS_B 0x1D0 0x438 0x4F8 0x1 0x2 +#define MX8MM_IOMUXC_SAI3_RXC_UART2_DTE_CTS_B 0x1D0 0x438 0x4F8 0x1 0x2 +#define MX8MM_IOMUXC_SAI3_RXC_UART2_DTE_RTS_B 0x1D0 0x438 0x000 0x1 0x0#define MX8MM_IOMUXC_SAI3_RXC_GPIO4_IO29 0x1D0 0x438 0x000 0x5 0x0#define MX8MM_IOMUXC_SAI3_RXC_TPSMP_HTRANS1 0x1D0 0x438 0x000 0x7 0x0#define MX8MM_IOMUXC_SAI3_RXD_SAI3_RX_DATA0 0x1D4 0x43C 0x000 0x0 0x0#define MX8MM_IOMUXC_SAI3_RXD_GPT1_COMPARE1 0x1D4 0x43C 0x000 0x1 0x0#define MX8MM_IOMUXC_SAI3_RXD_SAI5_RX_DATA0 0x1D4 0x43C 0x4D4 0x2 0x2 +#define MX8MM_IOMUXC_SAI3_RXD_UART2_DCE_RTS_B 0x1D0 0x438 0x4F8 0x1 0x3 +#define MX8MM_IOMUXC_SAI3_RXD_UART2_DTE_RTS_B 0x1D0 0x438 0x000 0x1 0x0 +#define MX8MM_IOMUXC_SAI3_RXD_UART2_DCE_CTS_B 0x1D0 0x438 0x000 0x1 0x0 +#define MX8MM_IOMUXC_SAI3_RXD_UART2_DTE_RTS_B 0x1D0 0x438 0x000 0x1 0x0 +#define MX8MM_IOMUXC_SAI3_RXD_UART2_DTE_CTS_B 0x1D0 0x438 0x4F8 0x1 0x3#define MX8MM_IOMUXC_SAI3_RXD_GPIO4_IO30 0x1D4 0x43C 0x000 0x5 0x0#define MX8MM_IOMUXC_SAI3_RXD_TPSMP_HDATA0 0x1D4 0x43C 0x000 0x7 0x0#define MX8MM_IOMUXC_SAI3_TXFS_SAI3_TX_SYNC 0x1D8 0x440 0x000 0x0 0x0#define MX8MM_IOMUXC_SAI3_TXFS_GPT1_CLK 0x1D8 0x440 0x000 0x1 0x0#define MX8MM_IOMUXC_SAI3_TXFS_SAI5_RX_DATA1 0x1D8 0x440 0x4D8 0x2 0x2 +#define MX8MM_IOMUXC_SAI3_TXFS_UART2_DCE_RX 0x1D8 0x440 0x4FC 0x4 0x2 +#define MX8MM_IOMUXC_SAI3_TXFS_UART2_DTE_TX 0x1D8 0x440 0x000 0x4 0x0#define MX8MM_IOMUXC_SAI3_TXFS_GPIO4_IO31 0x1D8 0x440 0x000 0x5 0x0#define MX8MM_IOMUXC_SAI3_TXFS_TPSMP_HDATA1 0x1D8 0x440 0x000 0x7 0x0#define MX8MM_IOMUXC_SAI3_TXC_SAI3_TX_BCLK 0x1DC 0x444 0x000 0x0 0x0#define MX8MM_IOMUXC_SAI3_TXC_GPT1_COMPARE2 0x1DC 0x444 0x000 0x1 0x0#define MX8MM_IOMUXC_SAI3_TXC_SAI5_RX_DATA2 0x1DC 0x444 0x4DC 0x2 0x2 +#define MX8MM_IOMUXC_SAI3_TXC_UART2_DCE_TX 0x1DC 0x444 0x000 0x4 0x0 +#define MX8MM_IOMUXC_SAI3_TXC_UART2_DTE_RX 0x1DC 0x444 0x4FC 0x4 0x3#define MX8MM_IOMUXC_SAI3_TXC_GPIO5_IO0 0x1DC 0x444 0x000 0x5 0x0#define MX8MM_IOMUXC_SAI3_TXC_TPSMP_HDATA2 0x1DC 0x444 0x000 0x7 0x0#define MX8MM_IOMUXC_SAI3_TXD_SAI3_TX_DATA0 0x1E0 0x448 0x000 0x0 0x0
Signature · 1 line
2.17.1
PATCH 1/5 dt-bindings: pinctrl: imx8mm: add alternative uart muxings
Quoted 7 lines · Igor Opaniuk
From: Max Krummenacher <[email protected]>
Add alternative UART muxing defines.
Signed-off-by Max Krummenacher <[email protected]>Signed-off-by Igor Opaniuk <[email protected]>
Quoted 74 lines
---
arch/arm/dts/imx8mm-pinfunc.h | 21 +++++++++++++++++++++ 1 file changed, 21 insertions(+)arch/arm/dts/imx8mm-pinfunc.h +21
-1@@ -430,18 +430,26 @@#define MX8MM_IOMUXC_SAI1_MCLK_SIM_M_HRESP 0x1AC 0x414 0x000 0x7 0x0#define MX8MM_IOMUXC_SAI2_RXFS_SAI2_RX_SYNC 0x1B0 0x418 0x000 0x0 0x0#define MX8MM_IOMUXC_SAI2_RXFS_SAI5_TX_SYNC 0x1B0 0x418 0x4EC 0x1 0x2 +#define MX8MM_IOMUXC_SAI2_RXFS_UART1_TX 0x1B0 0x418 0x000 0x4 0x0 +#define MX8MM_IOMUXC_SAI2_RXFS_UART1_RX 0x1B0 0x418 0x4F4 0x4 0x2#define MX8MM_IOMUXC_SAI2_RXFS_GPIO4_IO21 0x1B0 0x418 0x000 0x5 0x0#define MX8MM_IOMUXC_SAI2_RXFS_SIM_M_HSIZE0 0x1B0 0x418 0x000 0x7 0x0#define MX8MM_IOMUXC_SAI2_RXC_SAI2_RX_BCLK 0x1B4 0x41C 0x000 0x0 0x0#define MX8MM_IOMUXC_SAI2_RXC_SAI5_TX_BCLK 0x1B4 0x41C 0x4E8 0x1 0x2 +#define MX8MM_IOMUXC_SAI2_RXC_UART1_RX 0x1B4 0x41C 0x4F4 0x4 0x3 +#define MX8MM_IOMUXC_SAI2_RXC_UART1_TX 0x1B4 0x41C 0x000 0x4 0x0#define MX8MM_IOMUXC_SAI2_RXC_GPIO4_IO22 0x1B4 0x41C 0x000 0x5 0x0#define MX8MM_IOMUXC_SAI2_RXC_SIM_M_HSIZE1 0x1B4 0x41C 0x000 0x7 0x0#define MX8MM_IOMUXC_SAI2_RXD0_SAI2_RX_DATA0 0x1B8 0x420 0x000 0x0 0x0#define MX8MM_IOMUXC_SAI2_RXD0_SAI5_TX_DATA0 0x1B8 0x420 0x000 0x1 0x0 +#define MX8MM_IOMUXC_SAI2_RXD0_UART1_RTS_B 0x1B8 0x420 0x4F0 0x4 0x2 +#define MX8MM_IOMUXC_SAI2_RXD0_UART1_CTS_B 0x1B8 0x420 0x000 0x4 0x0#define MX8MM_IOMUXC_SAI2_RXD0_GPIO4_IO23 0x1B8 0x420 0x000 0x5 0x0#define MX8MM_IOMUXC_SAI2_RXD0_SIM_M_HSIZE2 0x1B8 0x420 0x000 0x7 0x0#define MX8MM_IOMUXC_SAI2_TXFS_SAI2_TX_SYNC 0x1BC 0x424 0x000 0x0 0x0#define MX8MM_IOMUXC_SAI2_TXFS_SAI5_TX_DATA1 0x1BC 0x424 0x000 0x1 0x0 +#define MX8MM_IOMUXC_SAI2_TXFS_UART1_CTS_B 0x1BC 0x424 0x000 0x4 0x0 +#define MX8MM_IOMUXC_SAI2_TXFS_UART1_RTS_B 0x1BC 0x424 0x4F0 0x4 0x3#define MX8MM_IOMUXC_SAI2_TXFS_GPIO4_IO24 0x1BC 0x424 0x000 0x5 0x0#define MX8MM_IOMUXC_SAI2_TXFS_SIM_M_HWRITE 0x1BC 0x424 0x000 0x7 0x0#define MX8MM_IOMUXC_SAI2_TXC_SAI2_TX_BCLK 0x1C0 0x428 0x000 0x0 0x0@@ -464,21 +472,34 @@#define MX8MM_IOMUXC_SAI3_RXC_SAI3_RX_BCLK 0x1D0 0x438 0x000 0x0 0x0#define MX8MM_IOMUXC_SAI3_RXC_GPT1_CAPTURE2 0x1D0 0x438 0x000 0x1 0x0#define MX8MM_IOMUXC_SAI3_RXC_SAI5_RX_BCLK 0x1D0 0x438 0x4D0 0x2 0x2 +#define MX8MM_IOMUXC_SAI3_RXC_UART2_DCE_CTS_B 0x1D0 0x438 0x000 0x1 0x0 +#define MX8MM_IOMUXC_SAI3_RXC_UART2_DCE_RTS_B 0x1D0 0x438 0x4F8 0x1 0x2 +#define MX8MM_IOMUXC_SAI3_RXC_UART2_DTE_CTS_B 0x1D0 0x438 0x4F8 0x1 0x2 +#define MX8MM_IOMUXC_SAI3_RXC_UART2_DTE_RTS_B 0x1D0 0x438 0x000 0x1 0x0#define MX8MM_IOMUXC_SAI3_RXC_GPIO4_IO29 0x1D0 0x438 0x000 0x5 0x0#define MX8MM_IOMUXC_SAI3_RXC_TPSMP_HTRANS1 0x1D0 0x438 0x000 0x7 0x0#define MX8MM_IOMUXC_SAI3_RXD_SAI3_RX_DATA0 0x1D4 0x43C 0x000 0x0 0x0#define MX8MM_IOMUXC_SAI3_RXD_GPT1_COMPARE1 0x1D4 0x43C 0x000 0x1 0x0#define MX8MM_IOMUXC_SAI3_RXD_SAI5_RX_DATA0 0x1D4 0x43C 0x4D4 0x2 0x2 +#define MX8MM_IOMUXC_SAI3_RXD_UART2_DCE_RTS_B 0x1D0 0x438 0x4F8 0x1 0x3 +#define MX8MM_IOMUXC_SAI3_RXD_UART2_DTE_RTS_B 0x1D0 0x438 0x000 0x1 0x0 +#define MX8MM_IOMUXC_SAI3_RXD_UART2_DCE_CTS_B 0x1D0 0x438 0x000 0x1 0x0 +#define MX8MM_IOMUXC_SAI3_RXD_UART2_DTE_RTS_B 0x1D0 0x438 0x000 0x1 0x0 +#define MX8MM_IOMUXC_SAI3_RXD_UART2_DTE_CTS_B 0x1D0 0x438 0x4F8 0x1 0x3#define MX8MM_IOMUXC_SAI3_RXD_GPIO4_IO30 0x1D4 0x43C 0x000 0x5 0x0#define MX8MM_IOMUXC_SAI3_RXD_TPSMP_HDATA0 0x1D4 0x43C 0x000 0x7 0x0#define MX8MM_IOMUXC_SAI3_TXFS_SAI3_TX_SYNC 0x1D8 0x440 0x000 0x0 0x0#define MX8MM_IOMUXC_SAI3_TXFS_GPT1_CLK 0x1D8 0x440 0x000 0x1 0x0#define MX8MM_IOMUXC_SAI3_TXFS_SAI5_RX_DATA1 0x1D8 0x440 0x4D8 0x2 0x2 +#define MX8MM_IOMUXC_SAI3_TXFS_UART2_DCE_RX 0x1D8 0x440 0x4FC 0x4 0x2 +#define MX8MM_IOMUXC_SAI3_TXFS_UART2_DTE_TX 0x1D8 0x440 0x000 0x4 0x0#define MX8MM_IOMUXC_SAI3_TXFS_GPIO4_IO31 0x1D8 0x440 0x000 0x5 0x0#define MX8MM_IOMUXC_SAI3_TXFS_TPSMP_HDATA1 0x1D8 0x440 0x000 0x7 0x0#define MX8MM_IOMUXC_SAI3_TXC_SAI3_TX_BCLK 0x1DC 0x444 0x000 0x0 0x0#define MX8MM_IOMUXC_SAI3_TXC_GPT1_COMPARE2 0x1DC 0x444 0x000 0x1 0x0#define MX8MM_IOMUXC_SAI3_TXC_SAI5_RX_DATA2 0x1DC 0x444 0x4DC 0x2 0x2 +#define MX8MM_IOMUXC_SAI3_TXC_UART2_DCE_TX 0x1DC 0x444 0x000 0x4 0x0 +#define MX8MM_IOMUXC_SAI3_TXC_UART2_DTE_RX 0x1DC 0x444 0x4FC 0x4 0x3#define MX8MM_IOMUXC_SAI3_TXC_GPIO5_IO0 0x1DC 0x444 0x000 0x5 0x0#define MX8MM_IOMUXC_SAI3_TXC_TPSMP_HDATA2 0x1DC 0x444 0x000 0x7 0x0#define MX8MM_IOMUXC_SAI3_TXD_SAI3_TX_DATA0 0x1E0 0x448 0x000 0x0 0x0 --2.17.1
Signature · 6 lines
Best regards Oleksandr Suvorov Toradex AG Altsagenstrasse 5 | 6048 Horw/Luzern | Switzerland | T: +41 41 500 4800 (main line)
Fabio Estevam
reviewerPATCH 1/5 dt-bindings: pinctrl: imx8mm: add alternative uart muxings
In reply to Igor OpaniukHi Igor and Max,
Quoted 17 lines · Igor Opaniuk
From: Max Krummenacher <[email protected]>
Add alternative UART muxing defines.
Signed-off-by Max Krummenacher <[email protected]>Signed-off-by Igor Opaniuk <[email protected]>---
arch/arm/dts/imx8mm-pinfunc.h | 21 +++++++++++++++++++++ 1 file changed, 21 insertions(+)arch/arm/dts/imx8mm-pinfunc.h +0
-0
arch/arm/dts/imx8mm-pinfunc.h line 434
Quoted 5 lines
arch/arm/dts/imx8mm-pinfunc.h +2
-0@@ -430,18 +430,26 @@#define MX8MM_IOMUXC_SAI1_MCLK_SIM_M_HRESP 0x1AC 0x414 0x000 0x7 0x0#define MX8MM_IOMUXC_SAI2_RXFS_SAI2_RX_SYNC 0x1B0 0x418 0x000 0x0 0x0#define MX8MM_IOMUXC_SAI2_RXFS_SAI5_TX_SYNC 0x1B0 0x418 0x4EC 0x1 0x2 +#define MX8MM_IOMUXC_SAI2_RXFS_UART1_TX 0x1B0 0x418 0x000 0x4 0x0 +#define MX8MM_IOMUXC_SAI2_RXFS_UART1_RX 0x1B0 0x418 0x4F4 0x4 0x2
Couldn't you just import the definitions from Linux instead?
There we have:
#define MX8MM_IOMUXC_SAI2_RXFS_UART1_DCE_TX
0x1B0 0x418 0x000 0x4 0x0
#define MX8MM_IOMUXC_SAI2_RXFS_UART1_DTE_RX
0x1B0 0x418 0x4F4 0x4 0x2PATCH 1/5 dt-bindings: pinctrl: imx8mm: add alternative uart muxings
In reply to Igor OpaniukHi Igor
Quoted 79 lines · Igor Opaniuk
From: Max Krummenacher <[email protected]>
Add alternative UART muxing defines.
Signed-off-by Max Krummenacher <[email protected]>Signed-off-by Igor Opaniuk <[email protected]>Reviewed-by Oleksandr Suvorov <[email protected]>---
arch/arm/dts/imx8mm-pinfunc.h | 21 +++++++++++++++++++++ 1 file changed, 21 insertions(+)arch/arm/dts/imx8mm- renamed from arch/arm/dts/imx8mm-pinfunc.h +0
-0
pinfunc.h
indexe25f7fcd79..de43fb55cc100644arch/arm/dts/imx8mm-pinfunc.h +0
-0@@ -430,18 +430,26 @@ #define
MX8MM_IOMUXC_SAI1_MCLK_SIM_M_HRESP0
x1AC0x4140x0000x70x0
#defineMX8MM_IOMUXC_SAI2_RXFS_SAI2_RX_SYNC0
x1B00x4180x0000x00x0
#defineMX8MM_IOMUXC_SAI2_RXFS_SAI5_TX_SYNC0
x1B00x4180x4EC0x10x2
+#defineMX8MM_IOMUXC_SAI2_RXFS_UART1_TX0
x1B00x4180x0000x40x0
+#defineMX8MM_IOMUXC_SAI2_RXFS_UART1_RX0
x1B00x4180x4F40x40x2
#defineMX8MM_IOMUXC_SAI2_RXFS_GPIO4_IO210
x1B00x4180x0000x50x0
#defineMX8MM_IOMUXC_SAI2_RXFS_SIM_M_HSIZE00
x1B00x4180x0000x70x0
#defineMX8MM_IOMUXC_SAI2_RXC_SAI2_RX_BCLK0
x1B40x41C0x0000x00x0
#defineMX8MM_IOMUXC_SAI2_RXC_SAI5_TX_BCLK0
x1B40x41C0x4E80x10x2
+#defineMX8MM_IOMUXC_SAI2_RXC_UART1_RX0
x1B40x41C0x4F40x40x3
+#defineMX8MM_IOMUXC_SAI2_RXC_UART1_TX0
x1B40x41C0x0000x40x0
#defineMX8MM_IOMUXC_SAI2_RXC_GPIO4_IO220
x1B40x41C0x0000x50x0
#defineMX8MM_IOMUXC_SAI2_RXC_SIM_M_HSIZE10
x1B40x41C0x0000x70x0
#defineMX8MM_IOMUXC_SAI2_RXD0_SAI2_RX_DATA00
x1B80x4200x0000x00x0
#defineMX8MM_IOMUXC_SAI2_RXD0_SAI5_TX_DATA00
x1B80x4200x0000x10x0
+#defineMX8MM_IOMUXC_SAI2_RXD0_UART1_RTS_B0
x1B80x4200x4F00x40x2
+#defineMX8MM_IOMUXC_SAI2_RXD0_UART1_CTS_B0
x1B80x4200x0000x40x0
#defineMX8MM_IOMUXC_SAI2_RXD0_GPIO4_IO230
x1B80x4200x0000x50x0
#defineMX8MM_IOMUXC_SAI2_RXD0_SIM_M_HSIZE20
x1B80x4200x0000x70x0
#defineMX8MM_IOMUXC_SAI2_TXFS_SAI2_TX_SYNC0
x1BC0x4240x0000x00x0
#define
Quoted 8 lines
MX8MM_IOMUXC_SAI2_TXFS_SAI5_TX_DATA10
x1BC0x4240x0000x10x0
+#defineMX8MM_IOMUXC_SAI2_TXFS_UART1_CTS_B0
x1BC0x4240x0000x40x0
+#defineMX8MM_IOMUXC_SAI2_TXFS_UART1_RTS_B0
x1BC0x4240x4F00x40x3
Above actually came from some NXP downstream stuff. I will just include their patch in a v2 instead.
Quoted 23 lines
#define
MX8MM_IOMUXC_SAI2_TXFS_GPIO4_IO240
x1BC0x4240x0000x50x0
#defineMX8MM_IOMUXC_SAI2_TXFS_SIM_M_HWRITE0
x1BC0x4240x0000x70x0
#defineMX8MM_IOMUXC_SAI2_TXC_SAI2_TX_BCLK0
x1C00x4280x0000x00x0arch/arm/dts/imx8mm-pinfunc.h +0
-0@@ -464,21 +472,34 @@ #define
MX8MM_IOMUXC_SAI3_RXC_SAI3_RX_BCLK0
x1D00x4380x0000x00x0
#defineMX8MM_IOMUXC_SAI3_RXC_GPT1_CAPTURE20
x1D00x4380x0000x10x0
#defineMX8MM_IOMUXC_SAI3_RXC_SAI5_RX_BCLK0
x1D00x4380x4D00x20x2
+#defineMX8MM_IOMUXC_SAI3_RXC_UART2_DCE_CTS_B0
x1D00x4380x0000x10x0
+#define
Quoted 8 lines
MX8MM_IOMUXC_SAI3_RXC_UART2_DCE_RTS_B0
x1D00x4380x4F80x10x2
+#defineMX8MM_IOMUXC_SAI3_RXC_UART2_DTE_CTS_B0
x1D00x4380x4F80x10x2
+#defineMX8MM_IOMUXC_SAI3_RXC_UART2_DTE_RTS_B0
x1D00x4380x0000x10x0
Those still contain a copy-paste error Max later fixed. I will correct that in a v2.
Quoted 22 lines
#define
MX8MM_IOMUXC_SAI3_RXC_GPIO4_IO290
x1D00x4380x0000x50x0
#defineMX8MM_IOMUXC_SAI3_RXC_TPSMP_HTRANS10
x1D00x4380x0000x70x0
#defineMX8MM_IOMUXC_SAI3_RXD_SAI3_RX_DATA00
x1D40x43C0x0000x00x0
#defineMX8MM_IOMUXC_SAI3_RXD_GPT1_COMPARE10
x1D40x43C0x0000x10x0
#defineMX8MM_IOMUXC_SAI3_RXD_SAI5_RX_DATA00
x1D40x43C0x4D40x20x2
+#defineMX8MM_IOMUXC_SAI3_RXD_UART2_DCE_RTS_B0
x1D00x4380x4F80x10x3
+#defineMX8MM_IOMUXC_SAI3_RXD_UART2_DTE_RTS_B0
x1D00x4380x0000x10x0
+#define
Quoted 8 lines
MX8MM_IOMUXC_SAI3_RXD_UART2_DCE_CTS_B0
x1D00x4380x0000x10x0
+#defineMX8MM_IOMUXC_SAI3_RXD_UART2_DTE_RTS_B0
x1D00x4380x0000x10x0
+#defineMX8MM_IOMUXC_SAI3_RXD_UART2_DTE_CTS_B0
x1D00x4380x4F80x10x3
Dito plus I will remove a duplicateMX8MM_IOMUXC_SAI3_RXD_UART2_DTE_RTS_B.
Quoted 10 lines
#define
MX8MM_IOMUXC_SAI3_RXD_GPIO4_IO300
x1D40x43C0x0000x50x0
#defineMX8MM_IOMUXC_SAI3_RXD_TPSMP_HDATA00
x1D40x43C0x0000x70x0
#defineMX8MM_IOMUXC_SAI3_TXFS_SAI3_TX_SYNC0
x1D80x4400x0000x00x0
#define
Quoted 8 lines
MX8MM_IOMUXC_SAI3_TXFS_GPT1_CLK0
x1D80x4400x0000x10x0
#defineMX8MM_IOMUXC_SAI3_TXFS_SAI5_RX_DATA10
x1D80x4400x4D80x20x2
+#defineMX8MM_IOMUXC_SAI3_TXFS_UART2_DCE_RX0
x1D80x4400x4FC0x40x2
Here some more are missing.
Quoted 13 lines
+#define
MX8MM_IOMUXC_SAI3_TXFS_UART2_DTE_TX0
x1D80x4400x0000x40x0
#defineMX8MM_IOMUXC_SAI3_TXFS_GPIO4_IO310
x1D80x4400x0000x50x0
#defineMX8MM_IOMUXC_SAI3_TXFS_TPSMP_HDATA10
x1D80x4400x0000x70x0
#defineMX8MM_IOMUXC_SAI3_TXC_SAI3_TX_BCLK0
x1DC0x4440x0000x00x0
#define
Quoted 8 lines
MX8MM_IOMUXC_SAI3_TXC_GPT1_COMPARE20
x1DC0x4440x0000x10x0
#defineMX8MM_IOMUXC_SAI3_TXC_SAI5_RX_DATA20
x1DC0x4440x4DC0x20x2
+#defineMX8MM_IOMUXC_SAI3_TXC_UART2_DCE_TX0
x1DC0x4440x0000x40x0
Dito.
Quoted 4 lines
+#define
MX8MM_IOMUXC_SAI3_TXC_UART2_DTE_RX0
x1DC0x4440x4FC0x40x3
#define
Quoted 8 lines
MX8MM_IOMUXC_SAI3_TXC_GPIO5_IO00
x1DC0x4440x0000x50x0
#defineMX8MM_IOMUXC_SAI3_TXC_TPSMP_HDATA20
x1DC0x4440x0000x70x0
#defineMX8MM_IOMUXC_SAI3_TXD_SAI3_TX_DATA00
x1E00x4480x0000x00x0
Cheers
Marcel
PATCH 2/5 toradex: tdx-cfg-block: add Verdin i.MX8MM support
In reply to Igor OpaniukFrom: Marcel Ziswiler <[email protected]>
Add support for storing configuration for Verdin i.MX8MM SoM in Toradex config block.
---
board/toradex/common/tdx-cfg-block.c | 17 +++++++++++++++-- board/toradex/common/tdx-cfg-block.h | 1 + 2 files changed, 16 insertions(+), 2 deletions(-)
board/toradex/common/tdx-cfg-block.c +15 -2
@@ -9,7 +9,8 @@#if defined(CONFIG_TARGET_APALIS_IMX6 ) || \ defined(CONFIG_TARGET_APALIS_IMX8 ) || \ defined(CONFIG_TARGET_COLIBRI_IMX6 ) || \ - defined(CONFIG_TARGET_COLIBRI_IMX8X ) + defined(CONFIG_TARGET_COLIBRI_IMX8X ) || \ + defined(CONFIG_TARGET_VERDIN_IMX8MM )#include <asm/arch/sys_proto.h> #else #define is_cpu_type (cpu) (0)
@@ -112,6 +113,9 @@ const char * const toradex_modules[] = { [50] = "Colibri iMX8 QuadXPlus 2GB IT", [51] = "Colibri iMX8 DualX 1GB Wi-Fi / Bluetooth", [52] = "Colibri iMX8 DualX 1GB", + [53] = "Apalis iMX8 QuadXPlus 2GB ECC IT", + [54] = "Apalis iMX8 DualXPlus 1GB", + [55] = "Verdin iMX8M Mini 2GB Wi-Fi / BT IT", };#ifdef CONFIG_TDX_CFG_BLOCK_IS_IN_MMC
@@ -294,17 +298,24 @@ static int get_cfgblock_interactive(void)char *soc;char it ='n' ;char wb ='n' ; -int len; +int len =0 ;/* Unknown module by default */ tdx_hw_tag.prodid =0 ;if (cpu_is_pxa27x ())sprintf (message,"Is the module the 312 MHz version? [y/N] " ); +#if !defined(CONFIG_TARGET_VERDIN_IMX8MM ) else sprintf(message, "Is the module an IT version? [y/N] "); + len =cli_readline (message); it = console_buffer[0 ]; +#else + else + it ='y' ; +#endif + #if defined(CONFIG_TARGET_APALIS_IMX8) || \ defined(CONFIG_TARGET_COLIBRI_IMX6ULL) || \
@@ -357,6 +368,8 @@ static int get_cfgblock_interactive(void) tdx_hw_tag.prodid =COLIBRI_IMX7D ; else if (!strcmp("imx7s", soc)) tdx_hw_tag.prodid =COLIBRI_IMX7S ; + else if (is_cpu_type(MXC_CPU_IMX8MM)) + tdx_hw_tag.prodid = VERDIN_IMX8MM; else if (is_cpu_type(MXC_CPU_IMX8QM)) {if (it =='y' || it =='Y' ) {if (wb =='y' || wb =='Y' )
board/toradex/common/tdx-cfg-block.h +1 -0
@@ -73,6 +73,7 @@ enum {COLIBRI_IMX8QXP_IT ,/* 50 */ COLIBRI_IMX8DX_WIFI_BT ,COLIBRI_IMX8DX , + VERDIN_IMX8MM, };extern const char *const toradex_modules[];
Signature · 1 line
2.17.1
PATCH 2/5 toradex: tdx-cfg-block: add Verdin i.MX8MM support
Quoted 29 lines · Igor Opaniuk
From: Marcel Ziswiler <[email protected]>
Add support for storing configuration for Verdin i.MX8MM SoM in Toradex config block.
Signed-off-by Marcel Ziswiler <[email protected]>Signed-off-by Igor Opaniuk <[email protected]>---
board/toradex/common/tdx-cfg-block.c | 17 +++++++++++++++-- board/toradex/common/tdx-cfg-block.h | 1 + 2 files changed, 16 insertions(+), 2 deletions(-)board/toradex/common/tdx-cfg-block.c +2
-1@@ -9,7 +9,8 @@#if defined(CONFIG_TARGET_APALIS_IMX6 ) || \ defined(CONFIG_TARGET_APALIS_IMX8 ) || \ defined(CONFIG_TARGET_COLIBRI_IMX6 ) || \ - defined(CONFIG_TARGET_COLIBRI_IMX8X ) + defined(CONFIG_TARGET_COLIBRI_IMX8X ) || \ + defined(CONFIG_TARGET_VERDIN_IMX8MM )#include <asm/arch/sys_proto.h> #else #define is_cpu_type (cpu) (0)
board/toradex/common/tdx-cfg-block.c const char * const toradex_modules[] = { · line 119
Quoted 7 lines
board/toradex/common/tdx-cfg-block.c +3
-0@@ -112,6 +113,9 @@ const char * const toradex_modules[] = { [50] = "Colibri iMX8 QuadXPlus 2GB IT", [51] = "Colibri iMX8 DualX 1GB Wi-Fi / Bluetooth", [52] = "Colibri iMX8 DualX 1GB", + [53] = "Apalis iMX8 QuadXPlus 2GB ECC IT", + [54] = "Apalis iMX8 DualXPlus 1GB", + [55] = "Verdin iMX8M Mini 2GB Wi-Fi / BT IT", };
I think it is better to add missing Apalis iMX8 items in a separate commit. If you'll push the next version, please keep it in mind.
Anyway,
Quoted 52 lines
board/toradex/common/tdx-cfg-block.c +10
-1#ifdef CONFIG_TDX_CFG_BLOCK_IS_IN_MMC @@ -294,17 +298,24 @@ static int get_cfgblock_interactive(void)char *soc;char it ='n' ;char wb ='n' ; -int len; +int len =0 ;/* Unknown module by default */ tdx_hw_tag.prodid =0 ;if (cpu_is_pxa27x ())sprintf (message,"Is the module the 312 MHz version? [y/N] " ); +#if !defined(CONFIG_TARGET_VERDIN_IMX8MM ) else sprintf(message, "Is the module an IT version? [y/N] "); + len =cli_readline (message); it = console_buffer[0 ]; +#else + else + it ='y' ; +#endif + #if defined(CONFIG_TARGET_APALIS_IMX8) || \ defined(CONFIG_TARGET_COLIBRI_IMX6ULL) || \@@ -357,6 +368,8 @@ static int get_cfgblock_interactive(void) tdx_hw_tag.prodid =COLIBRI_IMX7D ; else if (!strcmp("imx7s", soc)) tdx_hw_tag.prodid =COLIBRI_IMX7S ; + else if (is_cpu_type(MXC_CPU_IMX8MM)) + tdx_hw_tag.prodid = VERDIN_IMX8MM; else if (is_cpu_type(MXC_CPU_IMX8QM)) {if (it =='y' || it =='Y' ) {if (wb =='y' || wb =='Y' )board/toradex/common/tdx-cfg-block.h +1
-1@@ -73,6 +73,7 @@ enum {COLIBRI_IMX8QXP_IT ,/* 50 */ COLIBRI_IMX8DX_WIFI_BT ,COLIBRI_IMX8DX , + VERDIN_IMX8MM, };extern const char *const toradex_modules[]; --2.17.1
Signature · 6 lines
Best regards Oleksandr Suvorov Toradex AG Altsagenstrasse 5 | 6048 Horw/Luzern | Switzerland | T: +41 41 500 4800 (main line)
PATCH 2/5 toradex: tdx-cfg-block: add Verdin i.MX8MM support
Hi Igor and Oleksandr
Quoted 34 lines · Oleksandr Suvorov
Quoted 32 lines · Igor Opaniuk
From: Marcel Ziswiler <[email protected]>
Add support for storing configuration for Verdin i.MX8MM SoM in Toradex config block.
Signed-off-by Marcel Ziswiler <[email protected]>Signed-off-by Igor Opaniuk <[email protected]>---
board/toradex/common/tdx-cfg-block.c | 17 +++++++++++++++-- board/toradex/common/tdx-cfg-block.h | 1 + 2 files changed, 16 insertions(+), 2 deletions(-)board/toradex/common/tdx-cfg-block.c +2
-1@@ -9,7 +9,8 @@#if defined(CONFIG_TARGET_APALIS_IMX6 ) || \ defined(CONFIG_TARGET_APALIS_IMX8 ) || \ defined(CONFIG_TARGET_COLIBRI_IMX6 ) || \ - defined(CONFIG_TARGET_COLIBRI_IMX8X ) + defined(CONFIG_TARGET_COLIBRI_IMX8X ) || \ + defined(CONFIG_TARGET_VERDIN_IMX8MM )#include <asm/arch/sys_proto.h> #else #define is_cpu_type (cpu) (0)@@ -112,6 +113,9 @@ const char * const toradex_modules[] = { [50] = "Colibri iMX8 QuadXPlus 2GB IT", [51] = "Colibri iMX8 DualX 1GB Wi-Fi / Bluetooth", [52] = "Colibri iMX8 DualX 1GB",
Quoted 8 lines
board/toradex/common/tdx-cfg-block.c const char * const toradex_modules[] = { · line 119
Quoted 4 lines
board/toradex/common/tdx-cfg-block.c +3
-0+ [53] = "Apalis iMX8 QuadXPlus 2GB ECC IT", + [54] = "Apalis iMX8 DualXPlus 1GB", + [55] = "Verdin iMX8M Mini 2GB Wi-Fi / BT IT", };I think it is better to add missing Apalis iMX8 items in a separate commit.
If you'll push the next version, please keep it in mind.
Yes, plus we meanwhile got the final Verdin SKU naming. I will update it accordingly in a v2.
Quoted 54 lines
Anyway,
Reviewed-by Oleksandr Suvorov <[email protected]>Quoted 50 lines
board/toradex/common/tdx-cfg-block.c +8
-1#ifdef CONFIG_TDX_CFG_BLOCK_IS_IN_MMC @@ -294,17 +298,24 @@ static int get_cfgblock_interactive(void)char *soc;char it ='n' ;char wb ='n' ; -int len; +int len =0 ;/* Unknown module by default */ tdx_hw_tag.prodid =0 ;if (cpu_is_pxa27x ()) sprintf(message, "Is the module the 312 MHz version? [y/N] "); +#if !defined(CONFIG_TARGET_VERDIN_IMX8MM ) else sprintf(message, "Is the module an IT version? [y/N] "); + len = cli_readline(message); it = console_buffer[0]; +#else + else + it = 'y'; +#endif +#if defined(CONFIG_TARGET_APALIS_IMX8) || \ defined(CONFIG_TARGET_COLIBRI_IMX6ULL) || \board/toradex/common/tdx-cfg-block.c +2
-0@@ -357,6 +368,8 @@ static int get_cfgblock_interactive(void) tdx_hw_tag.prodid =COLIBRI_IMX7D ; else if (!strcmp("imx7s", soc)) tdx_hw_tag.prodid =COLIBRI_IMX7S ; + else if (is_cpu_type(MXC_CPU_IMX8MM)) + tdx_hw_tag.prodid = VERDIN_IMX8MM; else if (is_cpu_type(MXC_CPU_IMX8QM)) {if (it =='y' || it =='Y' ) {if (wb =='y' || wb =='Y' )board/toradex/common/tdx-cfg-block.h +1
-0@@ -73,6 +73,7 @@ enum {COLIBRI_IMX8QXP_IT ,/* 50 */ COLIBRI_IMX8DX_WIFI_BT ,COLIBRI_IMX8DX , + VERDIN_IMX8MM, };
Quoted 12 lines
Quoted 4 lines
board/toradex/common/tdx-cfg-block.h +0
-1extern const char *const toradex_modules[]; --2.17.1
Signature · 6 lines
Best regards Oleksandr Suvorov Toradex AG Altsagenstrasse 5 | 6048 Horw/Luzern | Switzerland | T: +41 41 500 4800 (main line)
Cheers
Marcel
PATCH 3/5 board: toradex: add Verdin iMX8MM 2GB WB IT v1.0a
In reply to Igor OpaniukFrom: Igor Opaniuk <[email protected]>
This introduces initial support for the Toradex Verdin iMX8MM 2GB WB IT V1.0A module. They are now strapped to boot from eFuses which are factory fused to properly boot from their on-module eMMC. U-Boot supports booting from the on-module eMMC only, SDP support is disabled for now.
Functionality wise the following is known to be working:
- eMMC, 8-bit and 4-bit MMC/SD card slots
- Ethernet
- GPIOs
- I2C
Boot sequence is:
SPL ---> ATF (TF-A) ---> U-boot proper
ATF, U-boot proper and u-boot.dtb images are packed into FIT image, loaded by SPL.
U-Boot SPL 2020.01-01840-gd92bdc79cf-dirty (Jan 22 2020 - 18:50:57 +0200) Normal Boot
Trying to boot from MMC1
U-Boot 2020.01-01840-gd92bdc79cf-dirty (Jan 22 2020 - 18:50:57 +0200)
CPU: Freescale i.MX8MMQ rev1.0 at 0 MHz Reset cause: POR DRAM: 2 GiB MMC: FSL_SDHC: 0, FSL_SDHC: 1 Loading Environment from MMC... OK In: serial Out: serial Err: serial Model: Toradex Verdin iMX8M Mini 2GB Wi-Fi / BT IT V1.0A, Serial# 06535148 Net: Could not get PHY for FEC0: addr 7 eth0: ethernet at 30be0000 Hit any key to stop autoboot: 0
---
arch/arm/dts/Makefile | 3 +- arch/arm/dts/imx8mm-verdin-u-boot.dtsi | 103 ++ arch/arm/dts/imx8mm-verdin.dts | 854 +++++++++ arch/arm/mach-imx/imx8m/Kconfig | 7 + board/toradex/verdin-imx8mm/Kconfig | 30 + board/toradex/verdin-imx8mm/Makefile | 12 + board/toradex/verdin-imx8mm/imximage.cfg | 16 + board/toradex/verdin-imx8mm/lpddr4_timing.c | 1851 +++++++++++++++++++ board/toradex/verdin-imx8mm/spl.c | 183 ++ board/toradex/verdin-imx8mm/verdin-imx8mm.c | 74 + configs/verdin-imx8mm_defconfig | 88 + include/configs/verdin-imx8mm.h | 121 ++ 12 files changed, 3341 insertions(+), 1 deletion(-) create mode 100644 arch/arm/dts/imx8mm-verdin-u-boot.dtsi create mode 100644 arch/arm/dts/imx8mm-verdin.dts create mode 100644 board/toradex/verdin-imx8mm/Kconfig create mode 100644 board/toradex/verdin-imx8mm/Makefile create mode 100644 board/toradex/verdin-imx8mm/imximage.cfg create mode 100644 board/toradex/verdin-imx8mm/lpddr4_timing.c create mode 100644 board/toradex/verdin-imx8mm/spl.c create mode 100644 board/toradex/verdin-imx8mm/verdin-imx8mm.c create mode 100644 configs/verdin-imx8mm_defconfig create mode 100644 include/configs/verdin-imx8mm.h
arch/arm/dts/Makefile +2 -1
@@ -711,7 +711,8 @@ dtb-$(CONFIG_ARCH_IMX8M) += \ imx8mm-evk.dtb \ imx8mn-ddr4-evk.dtb \ imx8mq-evk.dtb \ - imx8mp-evk.dtb + imx8mp-evk.dtb \ + imx8mm-verdin.dtb dtb-$(CONFIG_ARCH_IMXRT) += imxrt1050-evk.dtb
arch/arm/dts/imx8mm-verdin-u-boot.dtsi new file +103 -0
103 lines not on this page · raw message
arch/arm/dts/imx8mm-verdin.dts new file +854 -0
854 lines not on this page · raw message
arch/arm/mach-imx/imx8m/Kconfig +7 -0
@@ -50,11 +50,18 @@ config TARGET_IMX8MP_EVK select SUPPORT_SPL select IMX8M_LPDDR4 +config TARGET_VERDIN_IMX8MM + bool "Support Toradex Verdin iMX8M Mini module" + select IMX8MM + select SUPPORT_SPL + select IMX8M_LPDDR4 + endchoice source "board/freescale/imx8mq_evk/Kconfig" source "board/freescale/imx8mm_evk/Kconfig" source "board/freescale/imx8mn_evk/Kconfig" source "board/freescale/imx8mp_evk/Kconfig" +source "board/toradex/verdin-imx8mm/Kconfig" endif
board/toradex/verdin-imx8mm/Kconfig new file +30 -0
@@ -0,0 +1,30 @@ +if TARGET_VERDIN_IMX8MM + +config SYS_BOARD + default "verdin-imx8mm" + +config SYS_VENDOR + default "toradex" + +config SYS_CONFIG_NAME + default "verdin-imx8mm" + +config TDX_CFG_BLOCK + default y + +config TDX_HAVE_MMC + default y + +config TDX_CFG_BLOCK_DEV + default "0" + +config TDX_CFG_BLOCK_PART + default "1" + +# Toradex config block in eMMC, at the end of 1st "boot sector" +config TDX_CFG_BLOCK_OFFSET + default "-512" + +source "board/toradex/common/Kconfig" + +endif
board/toradex/verdin-imx8mm/Makefile new file +12 -0
@@ -0,0 +1,12 @@ +# SPDX-License-Identifier: GPL-2.0+ +# +# Copyright 2018-2019 Toradex +# + +obj-y += verdin-imx8mm.o + +ifdef CONFIG_SPL_BUILD +obj-y += spl.o +obj-$(CONFIG_IMX8M_LPDDR4) += lpddr4_timing.o +obj-$(CONFIG_IMX8M_DDR4) += ddr4_timing.o +endif
board/toradex/verdin-imx8mm/imximage.cfg new file +16 -0
@@ -0,0 +1,16 @@ +/* SPDX-License-Identifier: GPL-2.0+ */ +/* + * Copyright 2019 Toradex AG + */ + +#define __ASSEMBLY__ + +FIT +BOOT_FROM emmc_fastboot +LOADER spl/u-boot-spl-ddr.bin 0x7E1000 +SECOND_LOADER u-boot.itb 0x40200000 0x60000 + +DDR_FW lpddr4_pmu_train_1d_imem.bin +DDR_FW lpddr4_pmu_train_1d_dmem.bin +DDR_FW lpddr4_pmu_train_2d_imem.bin +DDR_FW lpddr4_pmu_train_2d_dmem.bin
board/toradex/verdin-imx8mm/lpddr4_timing.c new file +1851 -0
1,851 lines not on this page · raw message
board/toradex/verdin-imx8mm/spl.c new file +183 -0
107 lines not on this page · raw message
board/toradex/verdin-imx8mm/verdin-imx8mm.c new file +74 -0
74 lines not on this page · raw message
configs/verdin-imx8mm_defconfig new file +88 -0
88 lines not on this page · raw message
include/configs/verdin-imx8mm.h new file +121 -0
121 lines not on this page · raw message
The rest of this diff is not shown. View the raw message.
Signature · 1 line
2.17.1
Part of the diff is not shown here. View the raw message.
PATCH 3/5 board: toradex: add Verdin iMX8MM 2GB WB IT v1.0a
Hi Igor
Quoted 78 lines · Igor Opaniuk
From: Igor Opaniuk <[email protected]>
This introduces initial support for the Toradex Verdin iMX8MM 2GB WB IT
V1.0A module. They are now strapped to boot from eFuses which are factory fused to properly boot from their on-module eMMC. U-Boot supports booting from the on-module eMMC only, SDP support is disabled
for now.Functionality wise the following is known to be working:
- eMMC, 8-bit and 4-bit MMC/SD card slots
- Ethernet
- GPIOs
- I2CBoot sequence is:
SPL ---> ATF (TF-A) ---> U-boot properATF, U-boot proper and u-boot.dtb images are packed into FIT image, loaded by SPL.
U-Boot SPL 2020.01-01840-gd92bdc79cf-dirty (Jan 22 2020 - 18:50:57 +0200)
Normal Boot
Trying to boot from MMC1U-Boot 2020.01-01840-gd92bdc79cf-dirty (Jan 22 2020 - 18:50:57 +0200)
CPU: Freescale i.MX8MMQ rev1.0 at 0 MHz Reset cause: POR DRAM: 2 GiB MMC: FSL_SDHC: 0, FSL_SDHC: 1 Loading Environment from MMC... OK In: serial Out: serial Err: serial Model: Toradex Verdin iMX8M Mini 2GB Wi-Fi / BT IT V1.0A, Serial# 06535148 Net: Could not get PHY for FEC0: addr 7 eth0: ethernet at 30be0000 Hit any key to stop autoboot: 0Signed-off-by Igor Opaniuk <[email protected]>Signed-off-by Max Krummenacher <[email protected]>Signed-off-by Marcel Ziswiler <[email protected]>---
arch/arm/dts/Makefile | 3 +- arch/arm/dts/imx8mm-verdin-u-boot.dtsi | 103 ++ arch/arm/dts/imx8mm-verdin.dts | 854 +++++++++ arch/arm/mach-imx/imx8m/Kconfig | 7 + board/toradex/verdin-imx8mm/Kconfig | 30 + board/toradex/verdin-imx8mm/Makefile | 12 + board/toradex/verdin-imx8mm/imximage.cfg | 16 + board/toradex/verdin-imx8mm/lpddr4_timing.c | 1851 +++++++++++++++++++ board/toradex/verdin-imx8mm/spl.c | 183 ++ board/toradex/verdin-imx8mm/verdin-imx8mm.c | 74 + configs/verdin-imx8mm_defconfig | 88 + include/configs/verdin-imx8mm.h | 121 ++ 12 files changed, 3341 insertions(+), 1 deletion(-) create mode 100644 arch/arm/dts/imx8mm-verdin-u-boot.dtsi create mode 100644 arch/arm/dts/imx8mm-verdin.dts create mode 100644 board/toradex/verdin-imx8mm/Kconfig create mode 100644 board/toradex/verdin-imx8mm/Makefile create mode 100644 board/toradex/verdin-imx8mm/imximage.cfg create mode 100644 board/toradex/verdin-imx8mm/lpddr4_timing.c create mode 100644 board/toradex/verdin-imx8mm/spl.c create mode 100644 board/toradex/verdin-imx8mm/verdin-imx8mm.c create mode 100644 configs/verdin-imx8mm_defconfig create mode 100644 include/configs/verdin-imx8mm.harch/arm/dts/Makefile +0
-0
arch/arm/dts/Makefile dtb-$(CONFIG_ARCH_IMX8M) += \ · line 715
Quoted 6 lines
arch/arm/dts/Makefile +2
-1@@ -711,7 +711,8 @@ dtb-$(CONFIG_ARCH_IMX8M) += \ imx8mm-evk.dtb \ imx8mn-ddr4-evk.dtb \ imx8mq-evk.dtb \ - imx8mp-evk.dtb + imx8mp-evk.dtb \ + imx8mm-verdin.dtb
We should preserve the alphabetical order.
arch/arm/dts/imx8mm-verdin-u-boot.dtsi line 1
Quoted 10 lines
arch/arm/dts/Makefile +0
-0dtb-$(CONFIG_ARCH_IMXRT) += imxrt1050-evk.dtbarch/arm/dts/imx8mm-verdin-u-boot.dtsi new file +1
-0@@ -0,0 +1,103 @@ +// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
I don't think any parentheses are needed.
arch/arm/dts/imx8mm-verdin-u-boot.dtsi line 3
Quoted 2 lines
arch/arm/dts/imx8mm-verdin-u-boot.dtsi new file +2
-0+/* + * Copyright 2019 Toradex AG
It's already 2020 now (;-p).
Quoted 90 lines
arch/arm/dts/imx8mm-verdin-u-boot.dtsi new file +90
-0+ */ + +&{/soc at 0} { + u-boot,dm-pre-reloc; + u-boot,dm-spl; +}; + +&clk { + u-boot,dm-spl; + u-boot,dm-pre-reloc; + /delete-property/ assigned-clocks; + /delete-property/ assigned-clock-parents; + /delete-property/ assigned-clock-rates; +}; + +&osc_24m { + u-boot,dm-spl; + u-boot,dm-pre-reloc; +}; + +&aips1 { + u-boot,dm-spl; + u-boot,dm-pre-reloc; +}; + +&aips2 { + u-boot,dm-spl; +}; + +&aips3 { + u-boot,dm-spl; +}; + +&iomuxc { + u-boot,dm-spl; +}; + +&pinctrl_uart1 { + u-boot,dm-spl; +}; + +&pinctrl_usdhc2 { + u-boot,dm-spl; +}; + +&gpio1 { + u-boot,dm-spl; +}; + +&gpio2 { + u-boot,dm-spl; +}; + +&gpio3 { + u-boot,dm-spl; +}; + +&gpio4 { + u-boot,dm-spl; +}; + +&gpio5 { + u-boot,dm-spl; +}; + +&uart1 { + u-boot,dm-spl; +}; + +&usdhc1 { + u-boot,dm-spl; +}; + +&usdhc2 { + u-boot,dm-spl; +}; + +&usdhc3 { + u-boot,dm-spl; +}; + +&i2c1 { + u-boot,dm-spl; +}; + +&{/soc at 0/bus at 30800000/i2c at 30a20000/pmic at 4b} { + u-boot,dm-spl; +}; + +&{/soc at 0/bus at 30800000/i2c at 30a20000/pmic at 4b/regulators} {
arch/arm/dts/imx8mm-verdin-u-boot.dtsi line 103
Quoted 10 lines
arch/arm/dts/imx8mm-verdin-u-boot.dtsi new file +10
-0+ u-boot,dm-spl; +}; + +&pinctrl_i2c1 { + u-boot,dm-spl; +}; + +&pinctrl_pmic { + u-boot,dm-spl; +};
I guess also the U-Boot specific device tree should adhere to alphabetical node ordering.
Quoted 19 lines
arch/arm/dts/imx8mm- renamed from arch/arm/dts/imx8mm-verdin.dts +0
-0
verdin.dts
new file mode 100644
index 0000000000..b450057d3aarch/arm/dts/imx8mm-verdin.dts new file +12
-0@@ -0,0 +1,854 @@ +// SPDX-License-Identifier: (GPL-2.0+ OR MIT) +/* + * Copyright 2019 Toradex AG + */ + +/dts-v1/; + +#include <dt-bindings/usb/pd.h> +#include "imx8mm.dtsi" + +/ { + model = "Toradex Verdin iMX8MM";
arch/arm/dts/imx8mm-verdin.dts line 22
Quoted 10 lines
arch/arm/dts/imx8mm-verdin.dts new file +10
-0+ compatible = "toradex,verdin-imx8mm", "fsl,imx8mm"; + + chosen { + stdout-path = &uart1; + }; + + regulators { + compatible = "simple-bus"; + #address-cells = <1>; + #size-cells = <0>;
This simple-bus stuff is ancient and has no space in mainline any longer.
Quoted 56 lines
arch/arm/dts/imx8mm-verdin.dts new file +55
-0+ reg_ethphy: regulator-ethphy { + compatible = "regulator-fixed"; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_reg_eth>; + regulator-name = "V3.3_ETH"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + gpio = <&gpio2 20 GPIO_ACTIVE_HIGH>; + enable-active-high; + }; + + reg_usdhc2_vmmc: regulator-usdhc2 { + compatible = "regulator-fixed"; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_usdhc2_pwr_en>; + regulator-name = "V3.3_SD"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + gpio = <&gpio3 5 GPIO_ACTIVE_HIGH>; + startup-delay-us = <2000>; + enable-active-high; + }; + + reg_usb_otg1_vbus: regulator-usb-otg1 { + compatible = "regulator-fixed"; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_reg_usb1_en>; + regulator-name = "usb_otg1_vbus"; + regulator-min-microvolt = <5000000>; + regulator-max-microvolt = <5000000>; + enable-active-high; + /* Verdin USB1_EN */ + gpio = <&gpio1 12 GPIO_ACTIVE_HIGH>; + }; + + reg_usb_otg2_vbus: regulator-usb-otg2 { + compatible = "regulator-fixed"; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_reg_usb2_en>; + regulator-name = "usb_otg2_vbus"; + regulator-min-microvolt = <5000000>; + regulator-max-microvolt = <5000000>; + enable-active-high; + /* Verdin USB2_EN */ + gpio = <&gpio1 14 GPIO_ACTIVE_HIGH>; + }; + }; +}; + +&A53_0 { + cpu-supply = <&buck2_reg>; +}; + +&clk { + assigned-clocks = <&clk IMX8MM_AUDIO_PLL1>, <&clk
IMX8MM_AUDIO_PLL2>;
arch/arm/dts/imx8mm-verdin.dts line 86
Quoted 8 lines
arch/arm/dts/imx8mm-verdin.dts new file +8
-0+ assigned-clock-rates = <786432000>, <722534400>; +}; + +&fec1 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_fec1>; + phy-handle = <ðphy0>; + phy-mode = "rgmii-id";
I believe PHY mode should just be rgmii.
Quoted 10 lines
arch/arm/dts/imx8mm-verdin.dts new file +10
-0+ phy-supply = <®_ethphy>; + fsl,magic-packet; + fsl,rgmii_rxc_dly; + fsl,rgmii_txc_dly; + status = "okay"; + + mdio { + #address-cells = <1>; + #size-cells = <0>; +
arch/arm/dts/imx8mm-verdin.dts line 106
Quoted 10 lines
arch/arm/dts/imx8mm-verdin.dts new file +10
-0+ ethphy0: ethernet-phy at 7 { + compatible = "ethernet-phy-ieee802.3-c22"; + interrupt-parent = <&gpio1>; + interrupts = <10 IRQ_TYPE_LEVEL_LOW>; + reg = <7>; + micrel,led-mode = <0>; + }; + }; +}; +
I will add some comments about what exactly below I2C buses are.
Quoted 112 lines
+&i2c1 {
arch/arm/dts/imx8mm-verdin.dts new file +111
-0+ clock-frequency = <400000>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_i2c1>; + status = "okay"; + + pmic at 4b { + compatible = "rohm,bd71847"; + reg = <0x4b>; + pinctrl-0 = <&pinctrl_pmic>; + interrupt-parent = <&gpio1>; + interrupts = <3 GPIO_ACTIVE_LOW>; + rohm,reset-snvs-powered; + + regulators { + buck1_reg: BUCK1 { + regulator-name = "BUCK1"; + regulator-min-microvolt = <700000>; + regulator-max-microvolt = <1300000>; + regulator-boot-on; + regulator-always-on; + regulator-ramp-delay = <1250>; + }; + + buck2_reg: BUCK2 { + regulator-name = "BUCK2"; + regulator-min-microvolt = <700000>; + regulator-max-microvolt = <1300000>; + regulator-boot-on; + regulator-always-on; + regulator-ramp-delay = <1250>; + rohm,dvs-run-voltage = <1000000>; + rohm,dvs-idle-voltage = <900000>; + }; + + buck3_reg: BUCK3 { + // BUCK5 in datasheet + regulator-name = "BUCK3"; + regulator-min-microvolt = <700000>; + regulator-max-microvolt = <1350000>; + regulator-boot-on; + regulator-always-on; + }; + + buck4_reg: BUCK4 { + // BUCK6 in datasheet + regulator-name = "BUCK4"; + regulator-min-microvolt = <3000000>; + regulator-max-microvolt = <3300000>; + regulator-boot-on; + regulator-always-on; + }; + + buck5_reg: BUCK5 { + // BUCK7 in datasheet + regulator-name = "BUCK5"; + regulator-min-microvolt = <1605000>; + regulator-max-microvolt = <1995000>; + regulator-boot-on; + regulator-always-on; + }; + + buck6_reg: BUCK6 { + // BUCK8 in datasheet + regulator-name = "BUCK6"; + regulator-min-microvolt = <800000>; + regulator-max-microvolt = <1400000>; + regulator-boot-on; + regulator-always-on; + }; + + ldo1_reg: LDO1 { + regulator-name = "LDO1"; + regulator-min-microvolt = <3000000>; + regulator-max-microvolt = <3300000>; + regulator-boot-on; + regulator-always-on; + }; + + ldo2_reg: LDO2 { + regulator-name = "LDO2"; + regulator-min-microvolt = <900000>; + regulator-max-microvolt = <900000>; + regulator-boot-on; + regulator-always-on; + }; + + ldo3_reg: LDO3 { + regulator-name = "LDO3"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <3300000>; + regulator-boot-on; + regulator-always-on; + }; + + ldo4_reg: LDO4 { + regulator-name = "LDO4"; + regulator-min-microvolt = <900000>; + regulator-max-microvolt = <1800000>; + regulator-boot-on; + regulator-always-on; + }; + + ldo5_reg: regulator at 12 { + reg = <12>; + regulator-compatible = "LDO5"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + }; + + ldo6_reg: LDO6 { + regulator-name = "LDO6";
arch/arm/dts/imx8mm-verdin.dts line 228
Quoted 10 lines
arch/arm/dts/imx8mm-verdin.dts new file +10
-0+ regulator-min-microvolt = <900000>; + regulator-max-microvolt = <1800000>; + regulator-boot-on; + regulator-always-on; + }; + }; + }; + + /* Epson RX8130 real time clock on carrier board */ + rtc: rx8130 at 32 {
Node names should be more generic e.g. just rtc and the label is not required.
arch/arm/dts/imx8mm-verdin.dts line 233
Quoted 5 lines
arch/arm/dts/imx8mm-verdin.dts new file +5
-0+ compatible = "epson,rx8130"; + reg = <0x32>; + }; + + adc: max11607 at 34 {
Dito.
arch/arm/dts/imx8mm-verdin.dts line 239
Quoted 6 lines
arch/arm/dts/imx8mm-verdin.dts new file +6
-0+ compatible = "maxim,max11607"; + reg = <0x34>; + vcc-supply = <&ldo5_reg>; + }; + + eeprom at 50 {
Bonus for good node name (;-p).
Quoted 25 lines
arch/arm/dts/imx8mm-verdin.dts new file +25
-0+ compatible = "st,24c02"; + pagesize = <16>; + reg = <0x50>; + }; +}; + +&i2c2 { + clock-frequency = <400000>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_i2c2>; + status = "okay"; +}; + +&i2c3 { + clock-frequency = <400000>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_i2c3>; + status = "okay"; +}; + +&i2c4 { + clock-frequency = <400000>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_i2c4>; + status = "okay";
arch/arm/dts/imx8mm-verdin.dts line 274
Quoted 10 lines
arch/arm/dts/imx8mm-verdin.dts new file +10
-0+ + gpio_expander_21: gpio-expander at 21 { + compatible = "nxp,pcal6416"; + gpio-controller; + #gpio-cells = <2>; + reg = <0x21>; + }; + + /* Current measurement into module VCC */ + ina219 at 40 {
This is just a hwmon.
Quoted 16 lines
arch/arm/dts/imx8mm-verdin.dts new file +16
-0+ compatible = "ti,ina219"; + reg = <0x40>; + shunt-resistor = <10000>; + status = "okay"; + }; + + /* EEPROM on MIPI-DSI to HDMI adapter */ + eeprom_50: eeprom at 50 { + compatible = "st,24c02"; + pagesize = <16>; + reg = <0x50>; + }; + + /* EEPROM on Verdin Development board */ + eeprom_57: eeprom at 57 { + compatible = "st,24c02";
arch/arm/dts/imx8mm-verdin.dts line 300
Quoted 10 lines
arch/arm/dts/imx8mm-verdin.dts new file +10
-0+ pagesize = <16>; + reg = <0x57>; + }; +}; + +&snvs_pwrkey { + status = "okay"; +}; + +/* Verdin UART3 */
I believe according to Verdin spec we use underscores for instance separation e.g. UART_3.
Quoted 28 lines
+&uart1 {
arch/arm/dts/imx8mm-verdin.dts new file +27
-0+ pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_uart1>; + fsl,uart-has-rtscts; + status = "okay"; +}; + +/* Verdin UART1 */ +&uart2 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_uart2>; + fsl,uart-has-rtscts; + status = "okay"; +}; + +/* Verdin UART2 */ +&uart3 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_uart3>; + fsl,uart-has-rtscts; + status = "okay"; +}; + +/* On-module eMMC */ +&usdhc1 { + bus-width = <8>; + keep-power-in-suspend; + non-removable;
arch/arm/dts/imx8mm-verdin.dts line 338
Quoted 10 lines
arch/arm/dts/imx8mm-verdin.dts new file +10
-0+ pinctrl-names = "default", "state_100mhz", "state_200mhz"; + pinctrl-0 = <&pinctrl_usdhc1>; + pinctrl-1 = <&pinctrl_usdhc1_100mhz>; + pinctrl-2 = <&pinctrl_usdhc1_200mhz>; + pm-ignore-notify; + status = "okay"; + /* TODO Strobe */ +}; + +/* Verdin SDIO 1 */
Dito e.g. SD_1.
arch/arm/dts/imx8mm-verdin.dts line 349
Quoted 11 lines
+&usdhc2 {
arch/arm/dts/imx8mm-verdin.dts new file +10
-0+ pinctrl-names = "default", "state_100mhz", "state_200mhz"; + pinctrl-0 = <&pinctrl_usdhc2>, <&pinctrl_usdhc2_cd>; + pinctrl-1 = <&pinctrl_usdhc2_100mhz>, <&pinctrl_usdhc2_cd>; + pinctrl-2 = <&pinctrl_usdhc2_200mhz>, <&pinctrl_usdhc2_cd>; + cd-gpios = <&gpio2 12 GPIO_ACTIVE_LOW>; + bus-width = <4>; + vmmc-supply = <®_usdhc2_vmmc>; + status = "okay"; +}; +
USB comes before USDHC.
Quoted 14 lines
+&usbotg1 {
arch/arm/dts/imx8mm-verdin.dts new file +13
-0+ dr_mode = "peripheral"; + picophy,pre-emp-curr-control = <3>; + picophy,dc-vol-level-adjust = <7>; + vbus-supply = <®_usb_otg1_vbus>; + status = "okay"; +}; + +&usbotg2 { + dr_mode = "host"; + picophy,pre-emp-curr-control = <3>; + picophy,dc-vol-level-adjust = <7>; + vbus-supply = <®_usb_otg2_vbus>; + status = "okay";
arch/arm/dts/imx8mm-verdin.dts line 373
Quoted 10 lines
arch/arm/dts/imx8mm-verdin.dts new file +10
-0+}; + +&wdog1 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_wdog>; + fsl,ext-reset-output; + status = "okay"; +}; + +&iomuxc {
That muxing had still some issues and got reworked. I will update it in a v2.
Quoted 683 lines
arch/arm/dts/imx8mm-verdin.dts new file +2
-0+ pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_gpio1>, <&pinctrl_gpio2>,<
&pinctrl_gpio3>,arch/arm/dts/imx8mm-verdin.dts new file +1
-0+ <&pinctrl_gpio4>, <&pinctrl_gpio5>,<
&pinctrl_gpio6>,arch/arm/dts/imx8mm-verdin.dts new file +1
-0+ <&pinctrl_gpio7>, <&pinctrl_gpio8>,<
&pinctrl_se050_ena>;arch/arm/dts/imx8mm-verdin.dts new file +25
-0+ + imx8mm-verdin { + pinctrl_ctrl_force_off_moci: forceoffgrp { + fsl,pins = < + /* SODIMM 250 */ + MX8MM_IOMUXC_SAI5_RXC_GPIO3_IO20 0x1c4 + >; + }; + + pinctrl_can1_int: can1intgrp { + fsl,pins = < + MX8MM_IOMUXC_GPIO1_IO06_GPIO1_IO6 0x1c4 + >; + }; + + pinctrl_can2_int: can2intgrp { + fsl,pins = < + MX8MM_IOMUXC_GPIO1_IO07_GPIO1_IO7 0x1c4 + >; + }; + + pinctrl_ecspi2: ecspi2grp { + fsl,pins = < + /* SODIMM 196 */ + MX8MM_IOMUXC_ECSPI2_SCLK_ECSPI2_SCLK
0x4arch/arm/dts/imx8mm-verdin.dts new file +2
-0+ /* SODIMM 200 */ + MX8MM_IOMUXC_ECSPI2_MOSI_ECSPI2_MOSI
0x4arch/arm/dts/imx8mm-verdin.dts new file +2
-0+ /* SODIMM 198 */ + MX8MM_IOMUXC_ECSPI2_MISO_ECSPI2_MISO
0x1c4arch/arm/dts/imx8mm-verdin.dts new file +2
-0+ /* SODIMM 202 */ + MX8MM_IOMUXC_ECSPI2_SS0_GPIO5_IO13
0x1c4arch/arm/dts/imx8mm-verdin.dts new file +6
-0+ >; + }; + + pinctrl_ecspi3: ecspi3grp { + fsl,pins = < + MX8MM_IOMUXC_UART1_RXD_ECSPI3_SCLK
0x4arch/arm/dts/imx8mm-verdin.dts new file +1
-0+ MX8MM_IOMUXC_UART1_TXD_ECSPI3_MOSI
0x4arch/arm/dts/imx8mm-verdin.dts new file +1
-0+ MX8MM_IOMUXC_UART2_RXD_ECSPI3_MISO
0x1c4arch/arm/dts/imx8mm-verdin.dts new file +8
-0+ MX8MM_IOMUXC_UART2_TXD_GPIO5_IO25 0x1c4 + MX8MM_IOMUXC_GPIO1_IO05_GPIO1_IO5 0x1c4 + >; + }; + + pinctrl_fec1: fec1grp { + fsl,pins = < + MX8MM_IOMUXC_ENET_MDC_ENET1_MDC
0x3arch/arm/dts/imx8mm-verdin.dts new file +2
-0+ MX8MM_IOMUXC_ENET_MDIO_ENET1_MDIO 0x3 + MX8MM_IOMUXC_ENET_TD3_ENET1_RGMII_TD3
0x1farch/arm/dts/imx8mm-verdin.dts new file +1
-0+ MX8MM_IOMUXC_ENET_TD2_ENET1_RGMII_TD2
0x1farch/arm/dts/imx8mm-verdin.dts new file +1
-0+ MX8MM_IOMUXC_ENET_TD1_ENET1_RGMII_TD1
0x1farch/arm/dts/imx8mm-verdin.dts new file +1
-0+ MX8MM_IOMUXC_ENET_TD0_ENET1_RGMII_TD0
0x1farch/arm/dts/imx8mm-verdin.dts new file +1
-0+ MX8MM_IOMUXC_ENET_RD3_ENET1_RGMII_RD3
0x91arch/arm/dts/imx8mm-verdin.dts new file +1
-0+ MX8MM_IOMUXC_ENET_RD2_ENET1_RGMII_RD2
0x91arch/arm/dts/imx8mm-verdin.dts new file +1
-0+ MX8MM_IOMUXC_ENET_RD1_ENET1_RGMII_RD1
0x91arch/arm/dts/imx8mm-verdin.dts new file +1
-0+ MX8MM_IOMUXC_ENET_RD0_ENET1_RGMII_RD0
0x91arch/arm/dts/imx8mm-verdin.dts new file +1
-0+ MX8MM_IOMUXC_ENET_TXC_ENET1_RGMII_TXC
0x1farch/arm/dts/imx8mm-verdin.dts new file +1
-0+ MX8MM_IOMUXC_ENET_RXC_ENET1_RGMII_RXC
0x91arch/arm/dts/imx8mm-verdin.dts new file +1
-0+ MX8MM_IOMUXC_ENET_RX_CTL_ENET1_RGMII_RX
_CTL0x91arch/arm/dts/imx8mm-verdin.dts new file +1
-0+ MX8MM_IOMUXC_ENET_TX_CTL_ENET1_RGMII_TX
_CTL0x1farch/arm/dts/imx8mm-verdin.dts new file +1
-0+ MX8MM_IOMUXC_GPIO1_IO10_GPIO1_IO10
0x1c4arch/arm/dts/imx8mm-verdin.dts new file +9
-0+ >; + }; + + pinctrl_flexspi0: flexspi0grp { + fsl,pins = < + /* SODIMM 52 */ + MX8MM_IOMUXC_NAND_ALE_QSPI_A_SCLK 0x1c2 + /* SODIMM 54 */ + MX8MM_IOMUXC_NAND_CE0_B_QSPI_A_SS0_B
0x82arch/arm/dts/imx8mm-verdin.dts new file +2
-0+ /* SODIMM 64 */ + MX8MM_IOMUXC_NAND_CE1_B_QSPI_A_SS1_B
0x82arch/arm/dts/imx8mm-verdin.dts new file +4
-0+ /* SODIMM 66 */ + MX8MM_IOMUXC_NAND_DQS_QSPI_A_DQS 0x82 + /* SODIMM 56 */ + MX8MM_IOMUXC_NAND_DATA00_QSPI_A_DATA0
0x82arch/arm/dts/imx8mm-verdin.dts new file +2
-0+ /* SODIMM 58 */ + MX8MM_IOMUXC_NAND_DATA01_QSPI_A_DATA1
0x82arch/arm/dts/imx8mm-verdin.dts new file +2
-0+ /* SODIMM 60 */ + MX8MM_IOMUXC_NAND_DATA02_QSPI_A_DATA2
0x82arch/arm/dts/imx8mm-verdin.dts new file +2
-0+ /* SODIMM 62 */ + MX8MM_IOMUXC_NAND_DATA03_QSPI_A_DATA3
0x82arch/arm/dts/imx8mm-verdin.dts new file +29
-0+ >; + }; + + /* + * (MEZ_)DSI_1_INT# shared with (MEZ_)GPIO_1 on + * Verdin Development Board + */ + pinctrl_gpio_hpd: gpiohpdgrp { + fsl,pins = < + /* SODIMM 17 */ + MX8MM_IOMUXC_NAND_RE_B_GPIO3_IO15 0x184 + >; + }; + + /* + * (MEZ_)GPIO_1 shared with (MEZ_)DSI_1_INT# on + * Verdin Development Board + */ + pinctrl_gpio1: gpio1grp { + fsl,pins = < + /* SODIMM 206 */ + MX8MM_IOMUXC_NAND_CE3_B_GPIO3_IO4 0x184 + >; + }; + + pinctrl_gpio2: gpio2grp { + fsl,pins = < + /* SODIMM 208 */ + MX8MM_IOMUXC_SPDIF_EXT_CLK_GPIO5_IO5
0x184arch/arm/dts/imx8mm-verdin.dts new file +28
-0+ >; + }; + + pinctrl_gpio3: gpio3grp { + fsl,pins = < + /* SODIMM 210 */ + MX8MM_IOMUXC_UART3_RXD_GPIO5_IO26 0x184 + >; + }; + + pinctrl_gpio4: gpio4grp { + fsl,pins = < + /* SODIMM 212 */ + MX8MM_IOMUXC_UART3_TXD_GPIO5_IO27 0x184 + >; + }; + + pinctrl_gpio5: gpio5grp { + fsl,pins = < + /* SODIMM 216 */ + MX8MM_IOMUXC_GPIO1_IO00_GPIO1_IO0 0x184 + >; + }; + + pinctrl_gpio6: gpio6grp { + fsl,pins = < + /* SODIMM 218 */ + MX8MM_IOMUXC_GPIO1_IO11_GPIO1_IO11
0x184arch/arm/dts/imx8mm-verdin.dts new file +21
-0+ >; + }; + + pinctrl_gpio7: gpio7grp { + fsl,pins = < + /* SODIMM 220 */ + MX8MM_IOMUXC_GPIO1_IO08_GPIO1_IO8 0x184 + >; + }; + + pinctrl_gpio8: gpio8grp { + fsl,pins = < + /* SODIMM 222 */ + MX8MM_IOMUXC_GPIO1_IO09_GPIO1_IO9 0x184 + >; + }; + + /* On Module I2C */ + pinctrl_i2c1: i2c1grp { + fsl,pins = < + MX8MM_IOMUXC_I2C1_SCL_I2C1_SCL 0x400001c6
arch/arm/dts/imx8mm-verdin.dts new file +1
-0+ MX8MM_IOMUXC_I2C1_SDA_I2C1_SDA 0x400001c6
arch/arm/dts/imx8mm-verdin.dts new file +8
-0+ >; + }; + + /* Verdin I2C_4_CSI */ + pinctrl_i2c2: i2c2grp { + fsl,pins = < + /* SODIMM 55 */ + MX8MM_IOMUXC_I2C2_SCL_I2C2_SCL 0x400001c6
arch/arm/dts/imx8mm-verdin.dts new file +2
-0+ /* SODIMM 53 */ + MX8MM_IOMUXC_I2C2_SDA_I2C2_SDA 0x400001c6
arch/arm/dts/imx8mm-verdin.dts new file +8
-0+ >; + }; + + /* Verdin I2C_2_DSI */ + pinctrl_i2c3: i2c3grp { + fsl,pins = < + /* SODIMM 95 */ + MX8MM_IOMUXC_I2C3_SCL_I2C3_SCL 0x400001c6
arch/arm/dts/imx8mm-verdin.dts new file +2
-0+ /* SODIMM 93 */ + MX8MM_IOMUXC_I2C3_SDA_I2C3_SDA 0x400001c6
arch/arm/dts/imx8mm-verdin.dts new file +8
-0+ >; + }; + + /* Verdin I2C_1 */ + pinctrl_i2c4: i2c4grp { + fsl,pins = < + /* SODIMM 14 */ + MX8MM_IOMUXC_I2C4_SCL_I2C4_SCL 0x400001c6
arch/arm/dts/imx8mm-verdin.dts new file +2
-0+ /* SODIMM 12 */ + MX8MM_IOMUXC_I2C4_SDA_I2C4_SDA 0x400001c6
arch/arm/dts/imx8mm-verdin.dts new file +8
-0+ >; + }; + + pinctrl_pcie0: pcie0grp { + fsl,pins = < + /* SODIMM 244 */ + MX8MM_IOMUXC_SAI5_RXFS_GPIO3_IO19 0x6 + MX8MM_IOMUXC_SD2_RESET_B_GPIO2_IO19
0x6arch/arm/dts/imx8mm-verdin.dts new file +12
-0+ >; + }; + + pinctrl_pmic: pmicirq { + fsl,pins = < + MX8MM_IOMUXC_GPIO1_IO03_GPIO1_IO3 0x41 + >; + }; + + pinctrl_reg_eth: regethgrp { + fsl,pins = < + MX8MM_IOMUXC_SD2_WP_GPIO2_IO20
0x184arch/arm/dts/imx8mm-verdin.dts new file +7
-0+ >; + }; + + pinctrl_sai2: sai2grp { + fsl,pins = < + /* SODIMM 32 */ + MX8MM_IOMUXC_SAI2_TXFS_SAI2_TX_SYNC
0xd6arch/arm/dts/imx8mm-verdin.dts new file +2
-0+ /* SODIMM 30 */ + MX8MM_IOMUXC_SAI2_TXC_SAI2_TX_BCLK
0xd6arch/arm/dts/imx8mm-verdin.dts new file +4
-0+ /* SODIMM 38 */ + MX8MM_IOMUXC_SAI2_MCLK_SAI2_MCLK 0xd6 + /* SODIMM 36 */ + MX8MM_IOMUXC_SAI2_RXD0_SAI2_RX_DATA0
0xd6arch/arm/dts/imx8mm-verdin.dts new file +2
-0+ /* SODIMM 34 */ + MX8MM_IOMUXC_SAI2_TXD0_SAI2_TX_DATA0
0xd6arch/arm/dts/imx8mm-verdin.dts new file +7
-0+ >; + }; + + pinctrl_sai5: sai5grp { + fsl,pins = < + /* SODIMM 48 */ + MX8MM_IOMUXC_SAI5_RXD0_SAI5_RX_DATA0
0xd6arch/arm/dts/imx8mm-verdin.dts new file +2
-0+ /* SODIMM 44 */ + MX8MM_IOMUXC_SAI5_RXD1_SAI5_TX_SYNC
0xd6arch/arm/dts/imx8mm-verdin.dts new file +2
-0+ /* SODIMM 42 */ + MX8MM_IOMUXC_SAI5_RXD2_SAI5_TX_BCLK
0xd6arch/arm/dts/imx8mm-verdin.dts new file +2
-0+ /* SODIMM 46 */ + MX8MM_IOMUXC_SAI5_RXD3_SAI5_TX_DATA0
0xd6arch/arm/dts/imx8mm-verdin.dts new file +13
-0+ >; + }; + + pinctrl_se050_ena: se050enagrp { + fsl,pins = < + MX8MM_IOMUXC_SAI1_TXD7_GPIO4_IO19 0x184 + >; + }; + + pinctrl_uart1: uart1grp { + fsl,pins = < + /* SODIMM 149 */ + MX8MM_IOMUXC_SAI2_RXFS_UART1_TX
0x1c4arch/arm/dts/imx8mm-verdin.dts new file +2
-0+ /* SODIMM 147 */ + MX8MM_IOMUXC_SAI2_RXC_UART1_RX
0x1c4arch/arm/dts/imx8mm-verdin.dts new file +7
-0+ >; + }; + + pinctrl_uart2: uart2grp { + fsl,pins = < + /* SODIMM 129 */ + MX8MM_IOMUXC_SAI3_TXFS_UART2_DCE_RX
0x1c4arch/arm/dts/imx8mm-verdin.dts new file +2
-0+ /* SODIMM 131 */ + MX8MM_IOMUXC_SAI3_TXC_UART2_DCE_TX
0x1c4arch/arm/dts/imx8mm-verdin.dts new file +2
-0+ /* SODIMM 133 */ + MX8MM_IOMUXC_SAI3_RXC_UART2_DCE_CTS_B
0x1c4arch/arm/dts/imx8mm-verdin.dts new file +2
-0+ /* SODIMM 135 */ + MX8MM_IOMUXC_SAI3_RXD_UART2_DCE_RTS_B
0x1c4arch/arm/dts/imx8mm-verdin.dts new file +7
-0+ >; + }; + + pinctrl_uart3: uart3grp { + fsl,pins = < + /* SODIMM 137 */ + MX8MM_IOMUXC_ECSPI1_SCLK_UART3_DCE_RX
0x1c4arch/arm/dts/imx8mm-verdin.dts new file +2
-0+ /* SODIMM 139 */ + MX8MM_IOMUXC_ECSPI1_MOSI_UART3_DCE_TX
0x1c4arch/arm/dts/imx8mm-verdin.dts new file +2
-0+ /* SODIMM 141 */ + MX8MM_IOMUXC_ECSPI1_MISO_UART3_DCE_CTS_B
0x1c4arch/arm/dts/imx8mm-verdin.dts new file +2
-0+ /* SODIMM 143 */ + MX8MM_IOMUXC_ECSPI1_SS0_UART3_DCE_RTS_B0x1c4arch/arm/dts/imx8mm-verdin.dts new file +7
-0+ >; + }; + + pinctrl_uart4: uart4grp { + fsl,pins = < + /* SODIMM 151 */ + MX8MM_IOMUXC_UART4_RXD_UART4_DCE_RX
0x1c4arch/arm/dts/imx8mm-verdin.dts new file +2
-0+ /* SODIMM 153 */ + MX8MM_IOMUXC_UART4_TXD_UART4_DCE_TX
0x1c4arch/arm/dts/imx8mm-verdin.dts new file +7
-0+ >; + }; + + pinctrl_reg_usb1_en: regusb1en { + fsl,pins = < + /* SODIMM 155 */ + MX8MM_IOMUXC_GPIO1_IO12_GPIO1_IO12
0x184arch/arm/dts/imx8mm-verdin.dts new file +7
-0+ >; + }; + + pinctrl_reg_usb2_en: regusb2en { + fsl,pins = < + /* SODIMM 185 */ + MX8MM_IOMUXC_GPIO1_IO14_GPIO1_IO14
0x184arch/arm/dts/imx8mm-verdin.dts new file +6
-0+ >; + }; + + pinctrl_usdhc1: usdhc1grp { + fsl,pins = < + MX8MM_IOMUXC_SD1_CLK_USDHC1_CLK
0x190arch/arm/dts/imx8mm-verdin.dts new file +1
-0+ MX8MM_IOMUXC_SD1_CMD_USDHC1_CMD
0x1d0arch/arm/dts/imx8mm-verdin.dts new file +1
-0+ MX8MM_IOMUXC_SD1_DATA0_USDHC1_DATA0
0x1d0arch/arm/dts/imx8mm-verdin.dts new file +1
-0+ MX8MM_IOMUXC_SD1_DATA1_USDHC1_DATA1
0x1d0arch/arm/dts/imx8mm-verdin.dts new file +1
-0+ MX8MM_IOMUXC_SD1_DATA2_USDHC1_DATA2
0x1d0arch/arm/dts/imx8mm-verdin.dts new file +1
-0+ MX8MM_IOMUXC_SD1_DATA3_USDHC1_DATA3
0x1d0arch/arm/dts/imx8mm-verdin.dts new file +1
-0+ MX8MM_IOMUXC_SD1_DATA4_USDHC1_DATA4
0x1d0arch/arm/dts/imx8mm-verdin.dts new file +1
-0+ MX8MM_IOMUXC_SD1_DATA5_USDHC1_DATA5
0x1d0arch/arm/dts/imx8mm-verdin.dts new file +1
-0+ MX8MM_IOMUXC_SD1_DATA6_USDHC1_DATA6
0x1d0arch/arm/dts/imx8mm-verdin.dts new file +1
-0+ MX8MM_IOMUXC_SD1_DATA7_USDHC1_DATA7
0x1d0arch/arm/dts/imx8mm-verdin.dts new file +1
-0+ MX8MM_IOMUXC_SD1_STROBE_USDHC1_STROBE
0x190arch/arm/dts/imx8mm-verdin.dts new file +6
-0+ >; + }; + + pinctrl_usdhc1_100mhz: usdhc1grp100mhz { + fsl,pins = < + MX8MM_IOMUXC_SD1_CLK_USDHC1_CLK
0x194arch/arm/dts/imx8mm-verdin.dts new file +1
-0+ MX8MM_IOMUXC_SD1_CMD_USDHC1_CMD
0x1d4arch/arm/dts/imx8mm-verdin.dts new file +1
-0+ MX8MM_IOMUXC_SD1_DATA0_USDHC1_DATA0
0x1d4arch/arm/dts/imx8mm-verdin.dts new file +1
-0+ MX8MM_IOMUXC_SD1_DATA1_USDHC1_DATA1
0x1d4arch/arm/dts/imx8mm-verdin.dts new file +1
-0+ MX8MM_IOMUXC_SD1_DATA2_USDHC1_DATA2
0x1d4arch/arm/dts/imx8mm-verdin.dts new file +1
-0+ MX8MM_IOMUXC_SD1_DATA3_USDHC1_DATA3
0x1d4arch/arm/dts/imx8mm-verdin.dts new file +1
-0+ MX8MM_IOMUXC_SD1_DATA4_USDHC1_DATA4
0x1d4arch/arm/dts/imx8mm-verdin.dts new file +1
-0+ MX8MM_IOMUXC_SD1_DATA5_USDHC1_DATA5
0x1d4arch/arm/dts/imx8mm-verdin.dts new file +1
-0+ MX8MM_IOMUXC_SD1_DATA6_USDHC1_DATA6
0x1d4arch/arm/dts/imx8mm-verdin.dts new file +1
-0+ MX8MM_IOMUXC_SD1_DATA7_USDHC1_DATA7
0x1d4arch/arm/dts/imx8mm-verdin.dts new file +1
-0+ MX8MM_IOMUXC_SD1_STROBE_USDHC1_STROBE
0x194arch/arm/dts/imx8mm-verdin.dts new file +6
-0+ >; + }; + + pinctrl_usdhc1_200mhz: usdhc1grp200mhz { + fsl,pins = < + MX8MM_IOMUXC_SD1_CLK_USDHC1_CLK
0x196arch/arm/dts/imx8mm-verdin.dts new file +1
-0+ MX8MM_IOMUXC_SD1_CMD_USDHC1_CMD
0x1d6arch/arm/dts/imx8mm-verdin.dts new file +1
-0+ MX8MM_IOMUXC_SD1_DATA0_USDHC1_DATA0
0x1d6arch/arm/dts/imx8mm-verdin.dts new file +1
-0+ MX8MM_IOMUXC_SD1_DATA1_USDHC1_DATA1
0x1d6arch/arm/dts/imx8mm-verdin.dts new file +1
-0+ MX8MM_IOMUXC_SD1_DATA2_USDHC1_DATA2
0x1d6arch/arm/dts/imx8mm-verdin.dts new file +1
-0+ MX8MM_IOMUXC_SD1_DATA3_USDHC1_DATA3
0x1d6arch/arm/dts/imx8mm-verdin.dts new file +1
-0+ MX8MM_IOMUXC_SD1_DATA4_USDHC1_DATA4
0x1d6arch/arm/dts/imx8mm-verdin.dts new file +1
-0+ MX8MM_IOMUXC_SD1_DATA5_USDHC1_DATA5
0x1d6arch/arm/dts/imx8mm-verdin.dts new file +1
-0+ MX8MM_IOMUXC_SD1_DATA6_USDHC1_DATA6
0x1d6arch/arm/dts/imx8mm-verdin.dts new file +1
-0+ MX8MM_IOMUXC_SD1_DATA7_USDHC1_DATA7
0x1d6arch/arm/dts/imx8mm-verdin.dts new file +1
-0+ MX8MM_IOMUXC_SD1_STROBE_USDHC1_STROBE
0x196arch/arm/dts/imx8mm-verdin.dts new file +21
-0+ >; + }; + + pinctrl_usdhc2_cd: usdhc2cdgrp { + fsl,pins = < + /* SODIMM 84 */ + MX8MM_IOMUXC_SD2_CD_B_GPIO2_IO12 0x1c4 + >; + }; + + pinctrl_usdhc2_pwr_en: usdhc2pwrengrp { + fsl,pins = < + /* SODIMM 76 */ + MX8MM_IOMUXC_NAND_CLE_GPIO3_IO5 0x184 + >; + }; + + pinctrl_usdhc2: usdhc2grp { + fsl,pins = < + /* SODIMM 78 */ + MX8MM_IOMUXC_SD2_CLK_USDHC2_CLK
0x190arch/arm/dts/imx8mm-verdin.dts new file +2
-0+ /* SODIMM 74 */ + MX8MM_IOMUXC_SD2_CMD_USDHC2_CMD
0x1d0arch/arm/dts/imx8mm-verdin.dts new file +2
-0+ /* SODIMM 80 */ + MX8MM_IOMUXC_SD2_DATA0_USDHC2_DATA0
0x1d0arch/arm/dts/imx8mm-verdin.dts new file +2
-0+ /* SODIMM 82 */ + MX8MM_IOMUXC_SD2_DATA1_USDHC2_DATA1
0x1d0arch/arm/dts/imx8mm-verdin.dts new file +2
-0+ /* SODIMM 70 */ + MX8MM_IOMUXC_SD2_DATA2_USDHC2_DATA2
0x1d0arch/arm/dts/imx8mm-verdin.dts new file +2
-0+ /* SODIMM 72 */ + MX8MM_IOMUXC_SD2_DATA3_USDHC2_DATA3
0x1d0arch/arm/dts/imx8mm-verdin.dts new file +1
-0+ MX8MM_IOMUXC_GPIO1_IO04_USDHC2_VSELECT
0x1d0arch/arm/dts/imx8mm-verdin.dts new file +8
-0+ >; + }; + + pinctrl_usdhc2_100mhz: usdhc2grp100mhz { + fsl,pins = < + MX8MM_IOMUXC_SD2_CLK_USDHC2_CLK 0x194 + MX8MM_IOMUXC_SD2_CMD_USDHC2_CMD 0x1d4 + MX8MM_IOMUXC_SD2_DATA0_USDHC2_DATA0
0x1d4arch/arm/dts/imx8mm-verdin.dts new file +1
-0+ MX8MM_IOMUXC_SD2_DATA1_USDHC2_DATA1
0x1d4arch/arm/dts/imx8mm-verdin.dts new file +1
-0+ MX8MM_IOMUXC_SD2_DATA2_USDHC2_DATA2
0x1d4arch/arm/dts/imx8mm-verdin.dts new file +1
-0+ MX8MM_IOMUXC_SD2_DATA3_USDHC2_DATA3
0x1d4arch/arm/dts/imx8mm-verdin.dts new file +1
-0+ MX8MM_IOMUXC_GPIO1_IO04_USDHC2_VSELECT
0x1d0arch/arm/dts/imx8mm-verdin.dts new file +8
-0+ >; + }; + + pinctrl_usdhc2_200mhz: usdhc2grp200mhz { + fsl,pins = < + MX8MM_IOMUXC_SD2_CLK_USDHC2_CLK 0x196 + MX8MM_IOMUXC_SD2_CMD_USDHC2_CMD 0x1d6 + MX8MM_IOMUXC_SD2_DATA0_USDHC2_DATA0
0x1d6arch/arm/dts/imx8mm-verdin.dts new file +1
-0+ MX8MM_IOMUXC_SD2_DATA1_USDHC2_DATA1
0x1d6arch/arm/dts/imx8mm-verdin.dts new file +1
-0+ MX8MM_IOMUXC_SD2_DATA2_USDHC2_DATA2
0x1d6arch/arm/dts/imx8mm-verdin.dts new file +1
-0+ MX8MM_IOMUXC_SD2_DATA3_USDHC2_DATA3
0x1d6arch/arm/dts/imx8mm-verdin.dts new file +1
-0+ MX8MM_IOMUXC_GPIO1_IO04_USDHC2_VSELECT
0x1d0arch/arm/dts/imx8mm-verdin.dts new file +8
-0+ >; + }; + + pinctrl_usdhc3: usdhc3grp { + fsl,pins = < + MX8MM_IOMUXC_NAND_WE_B_USDHC3_CLK 0x190 + MX8MM_IOMUXC_NAND_WP_B_USDHC3_CMD 0x1d0 + MX8MM_IOMUXC_NAND_DATA04_USDHC3_DATA0
0x1d0arch/arm/dts/imx8mm-verdin.dts new file +1
-0+ MX8MM_IOMUXC_NAND_DATA05_USDHC3_DATA1
0x1d0arch/arm/dts/imx8mm-verdin.dts new file +1
-0+ MX8MM_IOMUXC_NAND_DATA06_USDHC3_DATA2
0x1d0arch/arm/dts/imx8mm-verdin.dts new file +1
-0+ MX8MM_IOMUXC_NAND_DATA07_USDHC3_DATA3
0x1d0arch/arm/dts/imx8mm-verdin.dts new file +8
-0+ >; + }; + + pinctrl_usdhc3_100mhz: usdhc3grp100mhz { + fsl,pins = < + MX8MM_IOMUXC_NAND_WE_B_USDHC3_CLK 0x194 + MX8MM_IOMUXC_NAND_WP_B_USDHC3_CMD 0x1d4 + MX8MM_IOMUXC_NAND_DATA04_USDHC3_DATA0
0x1d4arch/arm/dts/imx8mm-verdin.dts new file +1
-0+ MX8MM_IOMUXC_NAND_DATA05_USDHC3_DATA1
0x1d4arch/arm/dts/imx8mm-verdin.dts new file +1
-0+ MX8MM_IOMUXC_NAND_DATA06_USDHC3_DATA2
0x1d4arch/arm/dts/imx8mm-verdin.dts new file +1
-0+ MX8MM_IOMUXC_NAND_DATA07_USDHC3_DATA3
0x1d4arch/arm/dts/imx8mm-verdin.dts new file +8
-0+ >; + }; + + pinctrl_usdhc3_200mhz: usdhc3grp200mhz { + fsl,pins = < + MX8MM_IOMUXC_NAND_WE_B_USDHC3_CLK 0x196 + MX8MM_IOMUXC_NAND_WP_B_USDHC3_CMD 0x1d6 + MX8MM_IOMUXC_NAND_DATA04_USDHC3_DATA0
0x1d6arch/arm/dts/imx8mm-verdin.dts new file +1
-0+ MX8MM_IOMUXC_NAND_DATA05_USDHC3_DATA1
0x1d6arch/arm/dts/imx8mm-verdin.dts new file +1
-0+ MX8MM_IOMUXC_NAND_DATA06_USDHC3_DATA2
0x1d6arch/arm/dts/imx8mm-verdin.dts new file +1
-0+ MX8MM_IOMUXC_NAND_DATA07_USDHC3_DATA3
0x1d6arch/arm/dts/imx8mm-verdin.dts new file +6
-0+ >; + }; + + pinctrl_wdog: wdoggrp { + fsl,pins = < + MX8MM_IOMUXC_GPIO1_IO02_WDOG1_WDOG_B
0xc6arch/arm/dts/imx8mm-verdin.dts new file +7
-0+ >; + }; + + pinctrl_wifi_ctrl: wifictrlgrp { + fsl,pins = < + /* WIFI_WKUP_BT */ + MX8MM_IOMUXC_NAND_READY_B_GPIO3_IO16
0x1c4arch/arm/dts/imx8mm-verdin.dts new file +2
-0+ /* WIFI_WKUP_WLAN */ + MX8MM_IOMUXC_SD1_RESET_B_GPIO2_IO10
0x1c4arch/arm/dts/imx8mm-verdin.dts new file +15
-0+ /* WIFI_W_WKUP_HOST */ + MX8MM_IOMUXC_SAI1_RXD7_GPIO4_IO9 0x1c4 + >; + }; + + pinctrl_wifi_pwr_en: wifipwrengrp { + fsl,pins = < + /* PMIC_EN_WIFI */ + MX8MM_IOMUXC_SAI5_MCLK_GPIO3_IO25 0x184 + >; + }; + + pinctrl_wifi_i2s: wifii2sgrp { + fsl,pins = < + MX8MM_IOMUXC_SAI1_RXD4_SAI6_TX_BCLK
0xd6arch/arm/dts/imx8mm-verdin.dts new file +1
-0+ MX8MM_IOMUXC_SAI1_RXD5_SAI6_TX_DATA0
0xd6arch/arm/dts/imx8mm-verdin.dts new file +1
-0+ MX8MM_IOMUXC_SAI1_RXD6_SAI6_TX_SYNC
0xd6arch/arm/dts/imx8mm-verdin.dts new file +1
-0+ MX8MM_IOMUXC_SAI1_TXD5_SAI6_RX_DATA0
0xd6arch/arm/dts/imx8mm-verdin.dts new file +4
-0+ >; + }; + }; +};arch/arm/mach- renamed from arch/arm/mach-imx/imx8m/Kconfig +0
-0imx/imx8m/Kconfig
index72affb1bdc..58f1758ab6100644arch/arm/mach-imx/imx8m/Kconfig +7
-0@@ -50,11 +50,18 @@ config TARGET_IMX8MP_EVK select SUPPORT_SPL select IMX8M_LPDDR4 +config TARGET_VERDIN_IMX8MM + bool "Support Toradex Verdin iMX8M Mini module" + select IMX8MM + select SUPPORT_SPL + select IMX8M_LPDDR4 + endchoice source "board/freescale/imx8mq_evk/Kconfig" source "board/freescale/imx8mm_evk/Kconfig" source "board/freescale/imx8mn_evk/Kconfig" source "board/freescale/imx8mp_evk/Kconfig" +source "board/toradex/verdin-imx8mm/Kconfig" endifboard/toradex/verdin-imx8mm/Kconfig new file +30
-0@@ -0,0 +1,30 @@ +if TARGET_VERDIN_IMX8MM + +config SYS_BOARD + default "verdin-imx8mm" + +config SYS_VENDOR + default "toradex" + +config SYS_CONFIG_NAME + default "verdin-imx8mm" + +config TDX_CFG_BLOCK + default y + +config TDX_HAVE_MMC + default y + +config TDX_CFG_BLOCK_DEV + default "0" + +config TDX_CFG_BLOCK_PART + default "1" + +# Toradex config block in eMMC, at the end of 1st "boot sector" +config TDX_CFG_BLOCK_OFFSET + default "-512" + +source "board/toradex/common/Kconfig" + +endifboard/toradex/verdin-imx8mm/Makefile new file +1
-0@@ -0,0 +1,12 @@ +# SPDX-License-Identifier: GPL-2.0+
board/toradex/verdin-imx8mm/Makefile line 11
Quoted 10 lines
board/toradex/verdin-imx8mm/Makefile new file +10
-0+# +# Copyright 2018-2019 Toradex +# + +obj-y += verdin-imx8mm.o + +ifdef CONFIG_SPL_BUILD +obj-y += spl.o +obj-$(CONFIG_IMX8M_LPDDR4) += lpddr4_timing.o +obj-$(CONFIG_IMX8M_DDR4) += ddr4_timing.o
I don't think any DDR4 aka non-LPDDR stuff exists for Verdin.
Quoted 1,906 lines
board/toradex/verdin-imx8mm/Makefile new file +1
-0+endifboard/toradex/verdin-imx8mm/imximage.cfg new file +16
-0@@ -0,0 +1,16 @@ +/* SPDX-License-Identifier: GPL-2.0+ */ +/* + * Copyright 2019 Toradex AG + */ + +#define __ASSEMBLY__ + +FIT +BOOT_FROM emmc_fastboot +LOADER spl/u-boot-spl-ddr.bin 0x7E1000 +SECOND_LOADER u-boot.itb 0x40200000 0x60000 + +DDR_FW lpddr4_pmu_train_1d_imem.bin +DDR_FW lpddr4_pmu_train_1d_dmem.bin +DDR_FW lpddr4_pmu_train_2d_imem.bin +DDR_FW lpddr4_pmu_train_2d_dmem.binboard/toradex/verdin-imx8mm/lpddr4_timing.c new file +9
-0@@ -0,0 +1,1851 @@ +// SPDX-License-Identifier: GPL-2.0+ +/* +* Copyright 2019 Toradex AG +* +* Generated code from MX8M_DDR_tool +* Align with uboot-imx_v2018.03_4.14.78_1.0.0_ga +* +* DDR calibration created with mscale_ddr_tool_v210_setup.exe using +* MX8M_Mini_LPDDR4_RPA_v14 Verdin iMX8MM V1.0.xlsx as of 1. Nov. 2019.
+ */board/toradex/verdin-imx8mm/lpddr4_timing.c new file +1841
-0+ +#include <linux/kernel.h> +#include <asm/arch/ddr.h> + +struct dram_cfg_param ddr_ddrc_cfg[] = { +/** Initialize DDRC registers **/ + {0x3d400304 ,0x1 }, + {0x3d400030 ,0x1 }, + {0x3d400000 ,0xa1080020 }, + {0x3d400020 ,0x203 }, + {0x3d400024 ,0x3a980 }, + {0x3d400064 ,0x5b00d2 }, + {0x3d4000d0 ,0xc00305ba }, + {0x3d4000d4 ,0x940000 }, + {0x3d4000dc ,0xd4002d }, + {0x3d4000e0 ,0x310000 }, + {0x3d4000e8 ,0x66004d }, + {0x3d4000ec ,0x16004d }, + {0x3d400100 ,0x191e1920 }, + {0x3d400104 ,0x60630 }, + {0x3d40010c ,0xb0b000 }, + {0x3d400110 ,0xe04080e }, + {0x3d400114 ,0x2040c0c }, + {0x3d400118 ,0x1010007 }, + {0x3d40011c ,0x401 }, + {0x3d400130 ,0x20600 }, + {0x3d400134 ,0xc100002 }, + {0x3d400138 ,0xd8 }, + {0x3d400144 ,0x96004b }, + {0x3d400180 ,0x2ee0017 }, + {0x3d400184 ,0x2605b8e }, + {0x3d400188 ,0x0 }, + {0x3d400190 ,0x497820a }, + {0x3d400194 ,0x80303 }, + {0x3d4001b4 ,0x170a }, + {0x3d4001a0 ,0xe0400018 }, + {0x3d4001a4 ,0xdf00e4 }, + {0x3d4001a8 ,0x80000000 }, + {0x3d4001b0 ,0x11 }, + {0x3d4001c0 ,0x1 }, + {0x3d4001c4 ,0x1 }, + {0x3d4000f4 ,0xc99 }, + {0x3d400108 ,0x70e1617 }, + {0x3d400200 ,0x1f }, + {0x3d40020c ,0x0 }, + {0x3d400210 ,0x1f1f }, + {0x3d400204 ,0x80808 }, + {0x3d400214 ,0x7070707 }, + {0x3d400218 ,0x7070707 }, + {0x3d400250 ,0x29001701 }, + {0x3d400254 ,0x2c }, + {0x3d40025c ,0x4000030 }, + {0x3d400264 ,0x900093e7 }, + {0x3d40026c ,0x2005574 }, + {0x3d400400 ,0x111 }, + {0x3d400408 ,0x72ff }, + {0x3d400494 ,0x2100e07 }, + {0x3d400498 ,0x620096 }, + {0x3d40049c ,0x1100e07 }, + {0x3d4004a0 ,0xc8012c }, + {0x3d402020 ,0x1 }, + {0x3d402024 ,0x7d00 }, + {0x3d402050 ,0x20d040 }, + {0x3d402064 ,0xc001c }, + {0x3d4020dc ,0x840000 }, + {0x3d4020e0 ,0x310000 }, + {0x3d4020e8 ,0x66004d }, + {0x3d4020ec ,0x16004d }, + {0x3d402100 ,0xa040305 }, + {0x3d402104 ,0x30407 }, + {0x3d402108 ,0x203060b }, + {0x3d40210c ,0x505000 }, + {0x3d402110 ,0x2040202 }, + {0x3d402114 ,0x2030202 }, + {0x3d402118 ,0x1010004 }, + {0x3d40211c ,0x301 }, + {0x3d402130 ,0x20300 }, + {0x3d402134 ,0xa100002 }, + {0x3d402138 ,0x1d }, + {0x3d402144 ,0x14000a }, + {0x3d402180 ,0x640004 }, + {0x3d402190 ,0x3818200 }, + {0x3d402194 ,0x80303 }, + {0x3d4021b4 ,0x100 }, + {0x3d4020f4 ,0xc99 }, + {0x3d403020 ,0x1 }, + {0x3d403024 ,0x1f40 }, + {0x3d403050 ,0x20d040 }, + {0x3d403064 ,0x30007 }, + {0x3d4030dc ,0x840000 }, + {0x3d4030e0 ,0x310000 }, + {0x3d4030e8 ,0x66004d }, + {0x3d4030ec ,0x16004d }, + {0x3d403100 ,0xa010102 }, + {0x3d403104 ,0x30404 }, + {0x3d403108 ,0x203060b }, + {0x3d40310c ,0x505000 }, + {0x3d403110 ,0x2040202 }, + {0x3d403114 ,0x2030202 }, + {0x3d403118 ,0x1010004 }, + {0x3d40311c ,0x301 }, + {0x3d403130 ,0x20300 }, + {0x3d403134 ,0xa100002 }, + {0x3d403138 ,0x8 }, + {0x3d403144 ,0x50003 }, + {0x3d403180 ,0x190004 }, + {0x3d403190 ,0x3818200 }, + {0x3d403194 ,0x80303 }, + {0x3d4031b4 ,0x100 }, + {0x3d4030f4 ,0xc99 }, + {0x3d400028 ,0x0 }, +}; + +/* PHY Initialize Configuration */ +struct dram_cfg_param ddr_ddrphy_cfg[] = { + {0x100a0 ,0x0 }, + {0x100a1 ,0x1 }, + {0x100a2 ,0x2 }, + {0x100a3 ,0x3 }, + {0x100a4 ,0x4 }, + {0x100a5 ,0x5 }, + {0x100a6 ,0x6 }, + {0x100a7 ,0x7 }, + {0x110a0 ,0x0 }, + {0x110a1 ,0x1 }, + {0x110a2 ,0x3 }, + {0x110a3 ,0x4 }, + {0x110a4 ,0x5 }, + {0x110a5 ,0x2 }, + {0x110a6 ,0x6 }, + {0x110a7 ,0x7 }, + {0x120a0 ,0x0 }, + {0x120a1 ,0x1 }, + {0x120a2 ,0x3 }, + {0x120a3 ,0x4 }, + {0x120a4 ,0x5 }, + {0x120a5 ,0x2 }, + {0x120a6 ,0x6 }, + {0x120a7 ,0x7 }, + {0x130a0 ,0x0 }, + {0x130a1 ,0x1 }, + {0x130a2 ,0x2 }, + {0x130a3 ,0x3 }, + {0x130a4 ,0x4 }, + {0x130a5 ,0x5 }, + {0x130a6 ,0x6 }, + {0x130a7 ,0x7 }, + {0x1005f ,0x1ff }, + {0x1015f ,0x1ff }, + {0x1105f ,0x1ff }, + {0x1115f ,0x1ff }, + {0x1205f ,0x1ff }, + {0x1215f ,0x1ff }, + {0x1305f ,0x1ff }, + {0x1315f ,0x1ff }, + {0x11005f ,0x1ff }, + {0x11015f ,0x1ff }, + {0x11105f ,0x1ff }, + {0x11115f ,0x1ff }, + {0x11205f ,0x1ff }, + {0x11215f ,0x1ff }, + {0x11305f ,0x1ff }, + {0x11315f ,0x1ff }, + {0x21005f ,0x1ff }, + {0x21015f ,0x1ff }, + {0x21105f ,0x1ff }, + {0x21115f ,0x1ff }, + {0x21205f ,0x1ff }, + {0x21215f ,0x1ff }, + {0x21305f ,0x1ff }, + {0x21315f ,0x1ff }, + {0x55 ,0x1ff }, + {0x1055 ,0x1ff }, + {0x2055 ,0x1ff }, + {0x3055 ,0x1ff }, + {0x4055 ,0x1ff }, + {0x5055 ,0x1ff }, + {0x6055 ,0x1ff }, + {0x7055 ,0x1ff }, + {0x8055 ,0x1ff }, + {0x9055 ,0x1ff }, + {0x200c5 ,0x19 }, + {0x1200c5 ,0x7 }, + {0x2200c5 ,0x7 }, + {0x2002e ,0x2 }, + {0x12002e ,0x2 }, + {0x22002e ,0x2 }, + {0x90204 ,0x0 }, + {0x190204 ,0x0 }, + {0x290204 ,0x0 }, + {0x20024 ,0x1ab }, + {0x2003a ,0x0 }, + {0x120024 ,0x1ab }, + {0x2003a ,0x0 }, + {0x220024 ,0x1ab }, + {0x2003a ,0x0 }, + {0x20056 ,0x3 }, + {0x120056 ,0xa }, + {0x220056 ,0xa }, + {0x1004d ,0xe00 }, + {0x1014d ,0xe00 }, + {0x1104d ,0xe00 }, + {0x1114d ,0xe00 }, + {0x1204d ,0xe00 }, + {0x1214d ,0xe00 }, + {0x1304d ,0xe00 }, + {0x1314d ,0xe00 }, + {0x11004d ,0xe00 }, + {0x11014d ,0xe00 }, + {0x11104d ,0xe00 }, + {0x11114d ,0xe00 }, + {0x11204d ,0xe00 }, + {0x11214d ,0xe00 }, + {0x11304d ,0xe00 }, + {0x11314d ,0xe00 }, + {0x21004d ,0xe00 }, + {0x21014d ,0xe00 }, + {0x21104d ,0xe00 }, + {0x21114d ,0xe00 }, + {0x21204d ,0xe00 }, + {0x21214d ,0xe00 }, + {0x21304d ,0xe00 }, + {0x21314d ,0xe00 }, + {0x10049 ,0xeba }, + {0x10149 ,0xeba }, + {0x11049 ,0xeba }, + {0x11149 ,0xeba }, + {0x12049 ,0xeba }, + {0x12149 ,0xeba }, + {0x13049 ,0xeba }, + {0x13149 ,0xeba }, + {0x110049 ,0xeba }, + {0x110149 ,0xeba }, + {0x111049 ,0xeba }, + {0x111149 ,0xeba }, + {0x112049 ,0xeba }, + {0x112149 ,0xeba }, + {0x113049 ,0xeba }, + {0x113149 ,0xeba }, + {0x210049 ,0xeba }, + {0x210149 ,0xeba }, + {0x211049 ,0xeba }, + {0x211149 ,0xeba }, + {0x212049 ,0xeba }, + {0x212149 ,0xeba }, + {0x213049 ,0xeba }, + {0x213149 ,0xeba }, + {0x43 ,0x63 }, + {0x1043 ,0x63 }, + {0x2043 ,0x63 }, + {0x3043 ,0x63 }, + {0x4043 ,0x63 }, + {0x5043 ,0x63 }, + {0x6043 ,0x63 }, + {0x7043 ,0x63 }, + {0x8043 ,0x63 }, + {0x9043 ,0x63 }, + {0x20018 ,0x3 }, + {0x20075 ,0x4 }, + {0x20050 ,0x0 }, + {0x20008 ,0x2ee }, + {0x120008 ,0x64 }, + {0x220008 ,0x19 }, + {0x20088 ,0x9 }, + {0x200b2 ,0xdc }, + {0x10043 ,0x5a1 }, + {0x10143 ,0x5a1 }, + {0x11043 ,0x5a1 }, + {0x11143 ,0x5a1 }, + {0x12043 ,0x5a1 }, + {0x12143 ,0x5a1 }, + {0x13043 ,0x5a1 }, + {0x13143 ,0x5a1 }, + {0x1200b2 ,0xdc }, + {0x110043 ,0x5a1 }, + {0x110143 ,0x5a1 }, + {0x111043 ,0x5a1 }, + {0x111143 ,0x5a1 }, + {0x112043 ,0x5a1 }, + {0x112143 ,0x5a1 }, + {0x113043 ,0x5a1 }, + {0x113143 ,0x5a1 }, + {0x2200b2 ,0xdc }, + {0x210043 ,0x5a1 }, + {0x210143 ,0x5a1 }, + {0x211043 ,0x5a1 }, + {0x211143 ,0x5a1 }, + {0x212043 ,0x5a1 }, + {0x212143 ,0x5a1 }, + {0x213043 ,0x5a1 }, + {0x213143 ,0x5a1 }, + {0x200fa ,0x1 }, + {0x1200fa ,0x1 }, + {0x2200fa ,0x1 }, + {0x20019 ,0x1 }, + {0x120019 ,0x1 }, + {0x220019 ,0x1 }, + {0x200f0 ,0x660 }, + {0x200f1 ,0x0 }, + {0x200f2 ,0x4444 }, + {0x200f3 ,0x8888 }, + {0x200f4 ,0x5665 }, + {0x200f5 ,0x0 }, + {0x200f6 ,0x0 }, + {0x200f7 ,0xf000 }, + {0x20025 ,0x0 }, + {0x2002d ,0x0 }, + {0x12002d ,0x0 }, + {0x22002d ,0x0 }, + {0x200c7 ,0x21 }, + {0x1200c7 ,0x21 }, + {0x2200c7 ,0x21 }, + {0x200ca ,0x24 }, + {0x1200ca ,0x24 }, + {0x2200ca ,0x24 }, +}; + +/* ddr phy trained csr */ +struct dram_cfg_param ddr_ddrphy_trained_csr[] = { + {0x200b2 ,0x0 }, + {0x1200b2 ,0x0 }, + {0x2200b2 ,0x0 }, + {0x200cb ,0x0 }, + {0x10043 ,0x0 }, + {0x110043 ,0x0 }, + {0x210043 ,0x0 }, + {0x10143 ,0x0 }, + {0x110143 ,0x0 }, + {0x210143 ,0x0 }, + {0x11043 ,0x0 }, + {0x111043 ,0x0 }, + {0x211043 ,0x0 }, + {0x11143 ,0x0 }, + {0x111143 ,0x0 }, + {0x211143 ,0x0 }, + {0x12043 ,0x0 }, + {0x112043 ,0x0 }, + {0x212043 ,0x0 }, + {0x12143 ,0x0 }, + {0x112143 ,0x0 }, + {0x212143 ,0x0 }, + {0x13043 ,0x0 }, + {0x113043 ,0x0 }, + {0x213043 ,0x0 }, + {0x13143 ,0x0 }, + {0x113143 ,0x0 }, + {0x213143 ,0x0 }, + {0x80 ,0x0 }, + {0x100080 ,0x0 }, + {0x200080 ,0x0 }, + {0x1080 ,0x0 }, + {0x101080 ,0x0 }, + {0x201080 ,0x0 }, + {0x2080 ,0x0 }, + {0x102080 ,0x0 }, + {0x202080 ,0x0 }, + {0x3080 ,0x0 }, + {0x103080 ,0x0 }, + {0x203080 ,0x0 }, + {0x4080 ,0x0 }, + {0x104080 ,0x0 }, + {0x204080 ,0x0 }, + {0x5080 ,0x0 }, + {0x105080 ,0x0 }, + {0x205080 ,0x0 }, + {0x6080 ,0x0 }, + {0x106080 ,0x0 }, + {0x206080 ,0x0 }, + {0x7080 ,0x0 }, + {0x107080 ,0x0 }, + {0x207080 ,0x0 }, + {0x8080 ,0x0 }, + {0x108080 ,0x0 }, + {0x208080 ,0x0 }, + {0x9080 ,0x0 }, + {0x109080 ,0x0 }, + {0x209080 ,0x0 }, + {0x10080 ,0x0 }, + {0x110080 ,0x0 }, + {0x210080 ,0x0 }, + {0x10180 ,0x0 }, + {0x110180 ,0x0 }, + {0x210180 ,0x0 }, + {0x11080 ,0x0 }, + {0x111080 ,0x0 }, + {0x211080 ,0x0 }, + {0x11180 ,0x0 }, + {0x111180 ,0x0 }, + {0x211180 ,0x0 }, + {0x12080 ,0x0 }, + {0x112080 ,0x0 }, + {0x212080 ,0x0 }, + {0x12180 ,0x0 }, + {0x112180 ,0x0 }, + {0x212180 ,0x0 }, + {0x13080 ,0x0 }, + {0x113080 ,0x0 }, + {0x213080 ,0x0 }, + {0x13180 ,0x0 }, + {0x113180 ,0x0 }, + {0x213180 ,0x0 }, + {0x10081 ,0x0 }, + {0x110081 ,0x0 }, + {0x210081 ,0x0 }, + {0x10181 ,0x0 }, + {0x110181 ,0x0 }, + {0x210181 ,0x0 }, + {0x11081 ,0x0 }, + {0x111081 ,0x0 }, + {0x211081 ,0x0 }, + {0x11181 ,0x0 }, + {0x111181 ,0x0 }, + {0x211181 ,0x0 }, + {0x12081 ,0x0 }, + {0x112081 ,0x0 }, + {0x212081 ,0x0 }, + {0x12181 ,0x0 }, + {0x112181 ,0x0 }, + {0x212181 ,0x0 }, + {0x13081 ,0x0 }, + {0x113081 ,0x0 }, + {0x213081 ,0x0 }, + {0x13181 ,0x0 }, + {0x113181 ,0x0 }, + {0x213181 ,0x0 }, + {0x100d0 ,0x0 }, + {0x1100d0 ,0x0 }, + {0x2100d0 ,0x0 }, + {0x101d0 ,0x0 }, + {0x1101d0 ,0x0 }, + {0x2101d0 ,0x0 }, + {0x110d0 ,0x0 }, + {0x1110d0 ,0x0 }, + {0x2110d0 ,0x0 }, + {0x111d0 ,0x0 }, + {0x1111d0 ,0x0 }, + {0x2111d0 ,0x0 }, + {0x120d0 ,0x0 }, + {0x1120d0 ,0x0 }, + {0x2120d0 ,0x0 }, + {0x121d0 ,0x0 }, + {0x1121d0 ,0x0 }, + {0x2121d0 ,0x0 }, + {0x130d0 ,0x0 }, + {0x1130d0 ,0x0 }, + {0x2130d0 ,0x0 }, + {0x131d0 ,0x0 }, + {0x1131d0 ,0x0 }, + {0x2131d0 ,0x0 }, + {0x100d1 ,0x0 }, + {0x1100d1 ,0x0 }, + {0x2100d1 ,0x0 }, + {0x101d1 ,0x0 }, + {0x1101d1 ,0x0 }, + {0x2101d1 ,0x0 }, + {0x110d1 ,0x0 }, + {0x1110d1 ,0x0 }, + {0x2110d1 ,0x0 }, + {0x111d1 ,0x0 }, + {0x1111d1 ,0x0 }, + {0x2111d1 ,0x0 }, + {0x120d1 ,0x0 }, + {0x1120d1 ,0x0 }, + {0x2120d1 ,0x0 }, + {0x121d1 ,0x0 }, + {0x1121d1 ,0x0 }, + {0x2121d1 ,0x0 }, + {0x130d1 ,0x0 }, + {0x1130d1 ,0x0 }, + {0x2130d1 ,0x0 }, + {0x131d1 ,0x0 }, + {0x1131d1 ,0x0 }, + {0x2131d1 ,0x0 }, + {0x10068 ,0x0 }, + {0x10168 ,0x0 }, + {0x10268 ,0x0 }, + {0x10368 ,0x0 }, + {0x10468 ,0x0 }, + {0x10568 ,0x0 }, + {0x10668 ,0x0 }, + {0x10768 ,0x0 }, + {0x10868 ,0x0 }, + {0x11068 ,0x0 }, + {0x11168 ,0x0 }, + {0x11268 ,0x0 }, + {0x11368 ,0x0 }, + {0x11468 ,0x0 }, + {0x11568 ,0x0 }, + {0x11668 ,0x0 }, + {0x11768 ,0x0 }, + {0x11868 ,0x0 }, + {0x12068 ,0x0 }, + {0x12168 ,0x0 }, + {0x12268 ,0x0 }, + {0x12368 ,0x0 }, + {0x12468 ,0x0 }, + {0x12568 ,0x0 }, + {0x12668 ,0x0 }, + {0x12768 ,0x0 }, + {0x12868 ,0x0 }, + {0x13068 ,0x0 }, + {0x13168 ,0x0 }, + {0x13268 ,0x0 }, + {0x13368 ,0x0 }, + {0x13468 ,0x0 }, + {0x13568 ,0x0 }, + {0x13668 ,0x0 }, + {0x13768 ,0x0 }, + {0x13868 ,0x0 }, + {0x10069 ,0x0 }, + {0x10169 ,0x0 }, + {0x10269 ,0x0 }, + {0x10369 ,0x0 }, + {0x10469 ,0x0 }, + {0x10569 ,0x0 }, + {0x10669 ,0x0 }, + {0x10769 ,0x0 }, + {0x10869 ,0x0 }, + {0x11069 ,0x0 }, + {0x11169 ,0x0 }, + {0x11269 ,0x0 }, + {0x11369 ,0x0 }, + {0x11469 ,0x0 }, + {0x11569 ,0x0 }, + {0x11669 ,0x0 }, + {0x11769 ,0x0 }, + {0x11869 ,0x0 }, + {0x12069 ,0x0 }, + {0x12169 ,0x0 }, + {0x12269 ,0x0 }, + {0x12369 ,0x0 }, + {0x12469 ,0x0 }, + {0x12569 ,0x0 }, + {0x12669 ,0x0 }, + {0x12769 ,0x0 }, + {0x12869 ,0x0 }, + {0x13069 ,0x0 }, + {0x13169 ,0x0 }, + {0x13269 ,0x0 }, + {0x13369 ,0x0 }, + {0x13469 ,0x0 }, + {0x13569 ,0x0 }, + {0x13669 ,0x0 }, + {0x13769 ,0x0 }, + {0x13869 ,0x0 }, + {0x1008c ,0x0 }, + {0x11008c ,0x0 }, + {0x21008c ,0x0 }, + {0x1018c ,0x0 }, + {0x11018c ,0x0 }, + {0x21018c ,0x0 }, + {0x1108c ,0x0 }, + {0x11108c ,0x0 }, + {0x21108c ,0x0 }, + {0x1118c ,0x0 }, + {0x11118c ,0x0 }, + {0x21118c ,0x0 }, + {0x1208c ,0x0 }, + {0x11208c ,0x0 }, + {0x21208c ,0x0 }, + {0x1218c ,0x0 }, + {0x11218c ,0x0 }, + {0x21218c ,0x0 }, + {0x1308c ,0x0 }, + {0x11308c ,0x0 }, + {0x21308c ,0x0 }, + {0x1318c ,0x0 }, + {0x11318c ,0x0 }, + {0x21318c ,0x0 }, + {0x1008d ,0x0 }, + {0x11008d ,0x0 }, + {0x21008d ,0x0 }, + {0x1018d ,0x0 }, + {0x11018d ,0x0 }, + {0x21018d ,0x0 }, + {0x1108d ,0x0 }, + {0x11108d ,0x0 }, + {0x21108d ,0x0 }, + {0x1118d ,0x0 }, + {0x11118d ,0x0 }, + {0x21118d ,0x0 }, + {0x1208d ,0x0 }, + {0x11208d ,0x0 }, + {0x21208d ,0x0 }, + {0x1218d ,0x0 }, + {0x11218d ,0x0 }, + {0x21218d ,0x0 }, + {0x1308d ,0x0 }, + {0x11308d ,0x0 }, + {0x21308d ,0x0 }, + {0x1318d ,0x0 }, + {0x11318d ,0x0 }, + {0x21318d ,0x0 }, + {0x100c0 ,0x0 }, + {0x1100c0 ,0x0 }, + {0x2100c0 ,0x0 }, + {0x101c0 ,0x0 }, + {0x1101c0 ,0x0 }, + {0x2101c0 ,0x0 }, + {0x102c0 ,0x0 }, + {0x1102c0 ,0x0 }, + {0x2102c0 ,0x0 }, + {0x103c0 ,0x0 }, + {0x1103c0 ,0x0 }, + {0x2103c0 ,0x0 }, + {0x104c0 ,0x0 }, + {0x1104c0 ,0x0 }, + {0x2104c0 ,0x0 }, + {0x105c0 ,0x0 }, + {0x1105c0 ,0x0 }, + {0x2105c0 ,0x0 }, + {0x106c0 ,0x0 }, + {0x1106c0 ,0x0 }, + {0x2106c0 ,0x0 }, + {0x107c0 ,0x0 }, + {0x1107c0 ,0x0 }, + {0x2107c0 ,0x0 }, + {0x108c0 ,0x0 }, + {0x1108c0 ,0x0 }, + {0x2108c0 ,0x0 }, + {0x110c0 ,0x0 }, + {0x1110c0 ,0x0 }, + {0x2110c0 ,0x0 }, + {0x111c0 ,0x0 }, + {0x1111c0 ,0x0 }, + {0x2111c0 ,0x0 }, + {0x112c0 ,0x0 }, + {0x1112c0 ,0x0 }, + {0x2112c0 ,0x0 }, + {0x113c0 ,0x0 }, + {0x1113c0 ,0x0 }, + {0x2113c0 ,0x0 }, + {0x114c0 ,0x0 }, + {0x1114c0 ,0x0 }, + {0x2114c0 ,0x0 }, + {0x115c0 ,0x0 }, + {0x1115c0 ,0x0 }, + {0x2115c0 ,0x0 }, + {0x116c0 ,0x0 }, + {0x1116c0 ,0x0 }, + {0x2116c0 ,0x0 }, + {0x117c0 ,0x0 }, + {0x1117c0 ,0x0 }, + {0x2117c0 ,0x0 }, + {0x118c0 ,0x0 }, + {0x1118c0 ,0x0 }, + {0x2118c0 ,0x0 }, + {0x120c0 ,0x0 }, + {0x1120c0 ,0x0 }, + {0x2120c0 ,0x0 }, + {0x121c0 ,0x0 }, + {0x1121c0 ,0x0 }, + {0x2121c0 ,0x0 }, + {0x122c0 ,0x0 }, + {0x1122c0 ,0x0 }, + {0x2122c0 ,0x0 }, + {0x123c0 ,0x0 }, + {0x1123c0 ,0x0 }, + {0x2123c0 ,0x0 }, + {0x124c0 ,0x0 }, + {0x1124c0 ,0x0 }, + {0x2124c0 ,0x0 }, + {0x125c0 ,0x0 }, + {0x1125c0 ,0x0 }, + {0x2125c0 ,0x0 }, + {0x126c0 ,0x0 }, + {0x1126c0 ,0x0 }, + {0x2126c0 ,0x0 }, + {0x127c0 ,0x0 }, + {0x1127c0 ,0x0 }, + {0x2127c0 ,0x0 }, + {0x128c0 ,0x0 }, + {0x1128c0 ,0x0 }, + {0x2128c0 ,0x0 }, + {0x130c0 ,0x0 }, + {0x1130c0 ,0x0 }, + {0x2130c0 ,0x0 }, + {0x131c0 ,0x0 }, + {0x1131c0 ,0x0 }, + {0x2131c0 ,0x0 }, + {0x132c0 ,0x0 }, + {0x1132c0 ,0x0 }, + {0x2132c0 ,0x0 }, + {0x133c0 ,0x0 }, + {0x1133c0 ,0x0 }, + {0x2133c0 ,0x0 }, + {0x134c0 ,0x0 }, + {0x1134c0 ,0x0 }, + {0x2134c0 ,0x0 }, + {0x135c0 ,0x0 }, + {0x1135c0 ,0x0 }, + {0x2135c0 ,0x0 }, + {0x136c0 ,0x0 }, + {0x1136c0 ,0x0 }, + {0x2136c0 ,0x0 }, + {0x137c0 ,0x0 }, + {0x1137c0 ,0x0 }, + {0x2137c0 ,0x0 }, + {0x138c0 ,0x0 }, + {0x1138c0 ,0x0 }, + {0x2138c0 ,0x0 }, + {0x100c1 ,0x0 }, + {0x1100c1 ,0x0 }, + {0x2100c1 ,0x0 }, + {0x101c1 ,0x0 }, + {0x1101c1 ,0x0 }, + {0x2101c1 ,0x0 }, + {0x102c1 ,0x0 }, + {0x1102c1 ,0x0 }, + {0x2102c1 ,0x0 }, + {0x103c1 ,0x0 }, + {0x1103c1 ,0x0 }, + {0x2103c1 ,0x0 }, + {0x104c1 ,0x0 }, + {0x1104c1 ,0x0 }, + {0x2104c1 ,0x0 }, + {0x105c1 ,0x0 }, + {0x1105c1 ,0x0 }, + {0x2105c1 ,0x0 }, + {0x106c1 ,0x0 }, + {0x1106c1 ,0x0 }, + {0x2106c1 ,0x0 }, + {0x107c1 ,0x0 }, + {0x1107c1 ,0x0 }, + {0x2107c1 ,0x0 }, + {0x108c1 ,0x0 }, + {0x1108c1 ,0x0 }, + {0x2108c1 ,0x0 }, + {0x110c1 ,0x0 }, + {0x1110c1 ,0x0 }, + {0x2110c1 ,0x0 }, + {0x111c1 ,0x0 }, + {0x1111c1 ,0x0 }, + {0x2111c1 ,0x0 }, + {0x112c1 ,0x0 }, + {0x1112c1 ,0x0 }, + {0x2112c1 ,0x0 }, + {0x113c1 ,0x0 }, + {0x1113c1 ,0x0 }, + {0x2113c1 ,0x0 }, + {0x114c1 ,0x0 }, + {0x1114c1 ,0x0 }, + {0x2114c1 ,0x0 }, + {0x115c1 ,0x0 }, + {0x1115c1 ,0x0 }, + {0x2115c1 ,0x0 }, + {0x116c1 ,0x0 }, + {0x1116c1 ,0x0 }, + {0x2116c1 ,0x0 }, + {0x117c1 ,0x0 }, + {0x1117c1 ,0x0 }, + {0x2117c1 ,0x0 }, + {0x118c1 ,0x0 }, + {0x1118c1 ,0x0 }, + {0x2118c1 ,0x0 }, + {0x120c1 ,0x0 }, + {0x1120c1 ,0x0 }, + {0x2120c1 ,0x0 }, + {0x121c1 ,0x0 }, + {0x1121c1 ,0x0 }, + {0x2121c1 ,0x0 }, + {0x122c1 ,0x0 }, + {0x1122c1 ,0x0 }, + {0x2122c1 ,0x0 }, + {0x123c1 ,0x0 }, + {0x1123c1 ,0x0 }, + {0x2123c1 ,0x0 }, + {0x124c1 ,0x0 }, + {0x1124c1 ,0x0 }, + {0x2124c1 ,0x0 }, + {0x125c1 ,0x0 }, + {0x1125c1 ,0x0 }, + {0x2125c1 ,0x0 }, + {0x126c1 ,0x0 }, + {0x1126c1 ,0x0 }, + {0x2126c1 ,0x0 }, + {0x127c1 ,0x0 }, + {0x1127c1 ,0x0 }, + {0x2127c1 ,0x0 }, + {0x128c1 ,0x0 }, + {0x1128c1 ,0x0 }, + {0x2128c1 ,0x0 }, + {0x130c1 ,0x0 }, + {0x1130c1 ,0x0 }, + {0x2130c1 ,0x0 }, + {0x131c1 ,0x0 }, + {0x1131c1 ,0x0 }, + {0x2131c1 ,0x0 }, + {0x132c1 ,0x0 }, + {0x1132c1 ,0x0 }, + {0x2132c1 ,0x0 }, + {0x133c1 ,0x0 }, + {0x1133c1 ,0x0 }, + {0x2133c1 ,0x0 }, + {0x134c1 ,0x0 }, + {0x1134c1 ,0x0 }, + {0x2134c1 ,0x0 }, + {0x135c1 ,0x0 }, + {0x1135c1 ,0x0 }, + {0x2135c1 ,0x0 }, + {0x136c1 ,0x0 }, + {0x1136c1 ,0x0 }, + {0x2136c1 ,0x0 }, + {0x137c1 ,0x0 }, + {0x1137c1 ,0x0 }, + {0x2137c1 ,0x0 }, + {0x138c1 ,0x0 }, + {0x1138c1 ,0x0 }, + {0x2138c1 ,0x0 }, + {0x10020 ,0x0 }, + {0x110020 ,0x0 }, + {0x210020 ,0x0 }, + {0x11020 ,0x0 }, + {0x111020 ,0x0 }, + {0x211020 ,0x0 }, + {0x12020 ,0x0 }, + {0x112020 ,0x0 }, + {0x212020 ,0x0 }, + {0x13020 ,0x0 }, + {0x113020 ,0x0 }, + {0x213020 ,0x0 }, + {0x20072 ,0x0 }, + {0x20073 ,0x0 }, + {0x20074 ,0x0 }, + {0x100aa ,0x0 }, + {0x110aa ,0x0 }, + {0x120aa ,0x0 }, + {0x130aa ,0x0 }, + {0x20010 ,0x0 }, + {0x120010 ,0x0 }, + {0x220010 ,0x0 }, + {0x20011 ,0x0 }, + {0x120011 ,0x0 }, + {0x220011 ,0x0 }, + {0x100ae ,0x0 }, + {0x1100ae ,0x0 }, + {0x2100ae ,0x0 }, + {0x100af ,0x0 }, + {0x1100af ,0x0 }, + {0x2100af ,0x0 }, + {0x110ae ,0x0 }, + {0x1110ae ,0x0 }, + {0x2110ae ,0x0 }, + {0x110af ,0x0 }, + {0x1110af ,0x0 }, + {0x2110af ,0x0 }, + {0x120ae ,0x0 }, + {0x1120ae ,0x0 }, + {0x2120ae ,0x0 }, + {0x120af ,0x0 }, + {0x1120af ,0x0 }, + {0x2120af ,0x0 }, + {0x130ae ,0x0 }, + {0x1130ae ,0x0 }, + {0x2130ae ,0x0 }, + {0x130af ,0x0 }, + {0x1130af ,0x0 }, + {0x2130af ,0x0 }, + {0x20020 ,0x0 }, + {0x120020 ,0x0 }, + {0x220020 ,0x0 }, + {0x100a0 ,0x0 }, + {0x100a1 ,0x0 }, + {0x100a2 ,0x0 }, + {0x100a3 ,0x0 }, + {0x100a4 ,0x0 }, + {0x100a5 ,0x0 }, + {0x100a6 ,0x0 }, + {0x100a7 ,0x0 }, + {0x110a0 ,0x0 }, + {0x110a1 ,0x0 }, + {0x110a2 ,0x0 }, + {0x110a3 ,0x0 }, + {0x110a4 ,0x0 }, + {0x110a5 ,0x0 }, + {0x110a6 ,0x0 }, + {0x110a7 ,0x0 }, + {0x120a0 ,0x0 }, + {0x120a1 ,0x0 }, + {0x120a2 ,0x0 }, + {0x120a3 ,0x0 }, + {0x120a4 ,0x0 }, + {0x120a5 ,0x0 }, + {0x120a6 ,0x0 }, + {0x120a7 ,0x0 }, + {0x130a0 ,0x0 }, + {0x130a1 ,0x0 }, + {0x130a2 ,0x0 }, + {0x130a3 ,0x0 }, + {0x130a4 ,0x0 }, + {0x130a5 ,0x0 }, + {0x130a6 ,0x0 }, + {0x130a7 ,0x0 }, + {0x2007c ,0x0 }, + {0x12007c ,0x0 }, + {0x22007c ,0x0 }, + {0x2007d ,0x0 }, + {0x12007d ,0x0 }, + {0x22007d ,0x0 }, + {0x400fd ,0x0 }, + {0x400c0 ,0x0 }, + {0x90201 ,0x0 }, + {0x190201 ,0x0 }, + {0x290201 ,0x0 }, + {0x90202 ,0x0 }, + {0x190202 ,0x0 }, + {0x290202 ,0x0 }, + {0x90203 ,0x0 }, + {0x190203 ,0x0 }, + {0x290203 ,0x0 }, + {0x90204 ,0x0 }, + {0x190204 ,0x0 }, + {0x290204 ,0x0 }, + {0x90205 ,0x0 }, + {0x190205 ,0x0 }, + {0x290205 ,0x0 }, + {0x90206 ,0x0 }, + {0x190206 ,0x0 }, + {0x290206 ,0x0 }, + {0x90207 ,0x0 }, + {0x190207 ,0x0 }, + {0x290207 ,0x0 }, + {0x90208 ,0x0 }, + {0x190208 ,0x0 }, + {0x290208 ,0x0 }, + {0x10062 ,0x0 }, + {0x10162 ,0x0 }, + {0x10262 ,0x0 }, + {0x10362 ,0x0 }, + {0x10462 ,0x0 }, + {0x10562 ,0x0 }, + {0x10662 ,0x0 }, + {0x10762 ,0x0 }, + {0x10862 ,0x0 }, + {0x11062 ,0x0 }, + {0x11162 ,0x0 }, + {0x11262 ,0x0 }, + {0x11362 ,0x0 }, + {0x11462 ,0x0 }, + {0x11562 ,0x0 }, + {0x11662 ,0x0 }, + {0x11762 ,0x0 }, + {0x11862 ,0x0 }, + {0x12062 ,0x0 }, + {0x12162 ,0x0 }, + {0x12262 ,0x0 }, + {0x12362 ,0x0 }, + {0x12462 ,0x0 }, + {0x12562 ,0x0 }, + {0x12662 ,0x0 }, + {0x12762 ,0x0 }, + {0x12862 ,0x0 }, + {0x13062 ,0x0 }, + {0x13162 ,0x0 }, + {0x13262 ,0x0 }, + {0x13362 ,0x0 }, + {0x13462 ,0x0 }, + {0x13562 ,0x0 }, + {0x13662 ,0x0 }, + {0x13762 ,0x0 }, + {0x13862 ,0x0 }, + {0x20077 ,0x0 }, + {0x10001 ,0x0 }, + {0x11001 ,0x0 }, + {0x12001 ,0x0 }, + {0x13001 ,0x0 }, + {0x10040 ,0x0 }, + {0x10140 ,0x0 }, + {0x10240 ,0x0 }, + {0x10340 ,0x0 }, + {0x10440 ,0x0 }, + {0x10540 ,0x0 }, + {0x10640 ,0x0 }, + {0x10740 ,0x0 }, + {0x10840 ,0x0 }, + {0x10030 ,0x0 }, + {0x10130 ,0x0 }, + {0x10230 ,0x0 }, + {0x10330 ,0x0 }, + {0x10430 ,0x0 }, + {0x10530 ,0x0 }, + {0x10630 ,0x0 }, + {0x10730 ,0x0 }, + {0x10830 ,0x0 }, + {0x11040 ,0x0 }, + {0x11140 ,0x0 }, + {0x11240 ,0x0 }, + {0x11340 ,0x0 }, + {0x11440 ,0x0 }, + {0x11540 ,0x0 }, + {0x11640 ,0x0 }, + {0x11740 ,0x0 }, + {0x11840 ,0x0 }, + {0x11030 ,0x0 }, + {0x11130 ,0x0 }, + {0x11230 ,0x0 }, + {0x11330 ,0x0 }, + {0x11430 ,0x0 }, + {0x11530 ,0x0 }, + {0x11630 ,0x0 }, + {0x11730 ,0x0 }, + {0x11830 ,0x0 }, + {0x12040 ,0x0 }, + {0x12140 ,0x0 }, + {0x12240 ,0x0 }, + {0x12340 ,0x0 }, + {0x12440 ,0x0 }, + {0x12540 ,0x0 }, + {0x12640 ,0x0 }, + {0x12740 ,0x0 }, + {0x12840 ,0x0 }, + {0x12030 ,0x0 }, + {0x12130 ,0x0 }, + {0x12230 ,0x0 }, + {0x12330 ,0x0 }, + {0x12430 ,0x0 }, + {0x12530 ,0x0 }, + {0x12630 ,0x0 }, + {0x12730 ,0x0 }, + {0x12830 ,0x0 }, + {0x13040 ,0x0 }, + {0x13140 ,0x0 }, + {0x13240 ,0x0 }, + {0x13340 ,0x0 }, + {0x13440 ,0x0 }, + {0x13540 ,0x0 }, + {0x13640 ,0x0 }, + {0x13740 ,0x0 }, + {0x13840 ,0x0 }, + {0x13030 ,0x0 }, + {0x13130 ,0x0 }, + {0x13230 ,0x0 }, + {0x13330 ,0x0 }, + {0x13430 ,0x0 }, + {0x13530 ,0x0 }, + {0x13630 ,0x0 }, + {0x13730 ,0x0 }, + {0x13830 ,0x0 }, +}; + +/* P0 message block paremeter for training firmware */ +struct dram_cfg_param ddr_fsp0_cfg[] = { + {0xd0000 ,0x0 }, + {0x54003 ,0xbb8 }, + {0x54004 ,0x2 }, + {0x54005 ,0x2228 }, + {0x54006 ,0x11 }, + {0x54008 ,0x131f }, + {0x54009 ,0xc8 }, + {0x5400b ,0x2 }, + {0x5400d ,0x100 }, + {0x54012 ,0x110 }, + {0x54019 ,0x2dd4 }, + {0x5401a ,0x31 }, + {0x5401b ,0x4d66 }, + {0x5401c ,0x4d00 }, + {0x5401e ,0x16 }, + {0x5401f ,0x2dd4 }, + {0x54020 ,0x31 }, + {0x54021 ,0x4d66 }, + {0x54022 ,0x4d00 }, + {0x54024 ,0x16 }, + {0x5402b ,0x1000 }, + {0x5402c ,0x1 }, + {0x54032 ,0xd400 }, + {0x54033 ,0x312d }, + {0x54034 ,0x6600 }, + {0x54035 ,0x4d }, + {0x54036 ,0x4d }, + {0x54037 ,0x1600 }, + {0x54038 ,0xd400 }, + {0x54039 ,0x312d }, + {0x5403a ,0x6600 }, + {0x5403b ,0x4d }, + {0x5403c ,0x4d }, + {0x5403d ,0x1600 }, + {0xd0000 ,0x1 }, +}; + +/* P1 message block paremeter for training firmware */ +struct dram_cfg_param ddr_fsp1_cfg[] = { + {0xd0000 ,0x0 }, + {0x54002 ,0x101 }, + {0x54003 ,0x190 }, + {0x54004 ,0x2 }, + {0x54005 ,0x2228 }, + {0x54006 ,0x11 }, + {0x54008 ,0x121f }, + {0x54009 ,0xc8 }, + {0x5400b ,0x2 }, + {0x5400d ,0x100 }, + {0x54012 ,0x110 }, + {0x54019 ,0x84 }, + {0x5401a ,0x31 }, + {0x5401b ,0x4d66 }, + {0x5401c ,0x4d00 }, + {0x5401e ,0x16 }, + {0x5401f ,0x84 }, + {0x54020 ,0x31 }, + {0x54021 ,0x4d66 }, + {0x54022 ,0x4d00 }, + {0x54024 ,0x16 }, + {0x5402b ,0x1000 }, + {0x5402c ,0x1 }, + {0x54032 ,0x8400 }, + {0x54033 ,0x3100 }, + {0x54034 ,0x6600 }, + {0x54035 ,0x4d }, + {0x54036 ,0x4d }, + {0x54037 ,0x1600 }, + {0x54038 ,0x8400 }, + {0x54039 ,0x3100 }, + {0x5403a ,0x6600 }, + {0x5403b ,0x4d }, + {0x5403c ,0x4d }, + {0x5403d ,0x1600 }, + {0xd0000 ,0x1 }, +}; + +/* P2 message block paremeter for training firmware */ +struct dram_cfg_param ddr_fsp2_cfg[] = { + {0xd0000 ,0x0 }, + {0x54002 ,0x102 }, + {0x54003 ,0x64 }, + {0x54004 ,0x2 }, + {0x54005 ,0x2228 }, + {0x54006 ,0x11 }, + {0x54008 ,0x121f }, + {0x54009 ,0xc8 }, + {0x5400b ,0x2 }, + {0x5400d ,0x100 }, + {0x54012 ,0x110 }, + {0x54019 ,0x84 }, + {0x5401a ,0x31 }, + {0x5401b ,0x4d66 }, + {0x5401c ,0x4d00 }, + {0x5401e ,0x16 }, + {0x5401f ,0x84 }, + {0x54020 ,0x31 }, + {0x54021 ,0x4d66 }, + {0x54022 ,0x4d00 }, + {0x54024 ,0x16 }, + {0x5402b ,0x1000 }, + {0x5402c ,0x1 }, + {0x54032 ,0x8400 }, + {0x54033 ,0x3100 }, + {0x54034 ,0x6600 }, + {0x54035 ,0x4d }, + {0x54036 ,0x4d }, + {0x54037 ,0x1600 }, + {0x54038 ,0x8400 }, + {0x54039 ,0x3100 }, + {0x5403a ,0x6600 }, + {0x5403b ,0x4d }, + {0x5403c ,0x4d }, + {0x5403d ,0x1600 }, + {0xd0000 ,0x1 }, +}; + +/* P0 2D message block paremeter for training firmware */ +struct dram_cfg_param ddr_fsp0_2d_cfg[] = { + {0xd0000 ,0x0 }, + {0x54003 ,0xbb8 }, + {0x54004 ,0x2 }, + {0x54005 ,0x2228 }, + {0x54006 ,0x11 }, + {0x54008 ,0x61 }, + {0x54009 ,0xc8 }, + {0x5400b ,0x2 }, + {0x5400f ,0x100 }, + {0x54010 ,0x1f7f }, + {0x54012 ,0x110 }, + {0x54019 ,0x2dd4 }, + {0x5401a ,0x31 }, + {0x5401b ,0x4d66 }, + {0x5401c ,0x4d00 }, + {0x5401e ,0x16 }, + {0x5401f ,0x2dd4 }, + {0x54020 ,0x31 }, + {0x54021 ,0x4d66 }, + {0x54022 ,0x4d00 }, + {0x54024 ,0x16 }, + {0x5402b ,0x1000 }, + {0x5402c ,0x1 }, + {0x54032 ,0xd400 }, + {0x54033 ,0x312d }, + {0x54034 ,0x6600 }, + {0x54035 ,0x4d }, + {0x54036 ,0x4d }, + {0x54037 ,0x1600 }, + {0x54038 ,0xd400 }, + {0x54039 ,0x312d }, + {0x5403a ,0x6600 }, + {0x5403b ,0x4d }, + {0x5403c ,0x4d }, + {0x5403d ,0x1600 }, + {0xd0000 ,0x1 }, +}; + +/* DRAM PHY init engine image */ +struct dram_cfg_param ddr_phy_pie[] = { + {0xd0000 ,0x0 }, + {0x90000 ,0x10 }, + {0x90001 ,0x400 }, + {0x90002 ,0x10e }, + {0x90003 ,0x0 }, + {0x90004 ,0x0 }, + {0x90005 ,0x8 }, + {0x90029 ,0xb }, + {0x9002a ,0x480 }, + {0x9002b ,0x109 }, + {0x9002c ,0x8 }, + {0x9002d ,0x448 }, + {0x9002e ,0x139 }, + {0x9002f ,0x8 }, + {0x90030 ,0x478 }, + {0x90031 ,0x109 }, + {0x90032 ,0x0 }, + {0x90033 ,0xe8 }, + {0x90034 ,0x109 }, + {0x90035 ,0x2 }, + {0x90036 ,0x10 }, + {0x90037 ,0x139 }, + {0x90038 ,0xf }, + {0x90039 ,0x7c0 }, + {0x9003a ,0x139 }, + {0x9003b ,0x44 }, + {0x9003c ,0x630 }, + {0x9003d ,0x159 }, + {0x9003e ,0x14f }, + {0x9003f ,0x630 }, + {0x90040 ,0x159 }, + {0x90041 ,0x47 }, + {0x90042 ,0x630 }, + {0x90043 ,0x149 }, + {0x90044 ,0x4f }, + {0x90045 ,0x630 }, + {0x90046 ,0x179 }, + {0x90047 ,0x8 }, + {0x90048 ,0xe0 }, + {0x90049 ,0x109 }, + {0x9004a ,0x0 }, + {0x9004b ,0x7c8 }, + {0x9004c ,0x109 }, + {0x9004d ,0x0 }, + {0x9004e ,0x1 }, + {0x9004f ,0x8 }, + {0x90050 ,0x0 }, + {0x90051 ,0x45a }, + {0x90052 ,0x9 }, + {0x90053 ,0x0 }, + {0x90054 ,0x448 }, + {0x90055 ,0x109 }, + {0x90056 ,0x40 }, + {0x90057 ,0x630 }, + {0x90058 ,0x179 }, + {0x90059 ,0x1 }, + {0x9005a ,0x618 }, + {0x9005b ,0x109 }, + {0x9005c ,0x40c0 }, + {0x9005d ,0x630 }, + {0x9005e ,0x149 }, + {0x9005f ,0x8 }, + {0x90060 ,0x4 }, + {0x90061 ,0x48 }, + {0x90062 ,0x4040 }, + {0x90063 ,0x630 }, + {0x90064 ,0x149 }, + {0x90065 ,0x0 }, + {0x90066 ,0x4 }, + {0x90067 ,0x48 }, + {0x90068 ,0x40 }, + {0x90069 ,0x630 }, + {0x9006a ,0x149 }, + {0x9006b ,0x10 }, + {0x9006c ,0x4 }, + {0x9006d ,0x18 }, + {0x9006e ,0x0 }, + {0x9006f ,0x4 }, + {0x90070 ,0x78 }, + {0x90071 ,0x549 }, + {0x90072 ,0x630 }, + {0x90073 ,0x159 }, + {0x90074 ,0xd49 }, + {0x90075 ,0x630 }, + {0x90076 ,0x159 }, + {0x90077 ,0x94a }, + {0x90078 ,0x630 }, + {0x90079 ,0x159 }, + {0x9007a ,0x441 }, + {0x9007b ,0x630 }, + {0x9007c ,0x149 }, + {0x9007d ,0x42 }, + {0x9007e ,0x630 }, + {0x9007f ,0x149 }, + {0x90080 ,0x1 }, + {0x90081 ,0x630 }, + {0x90082 ,0x149 }, + {0x90083 ,0x0 }, + {0x90084 ,0xe0 }, + {0x90085 ,0x109 }, + {0x90086 ,0xa }, + {0x90087 ,0x10 }, + {0x90088 ,0x109 }, + {0x90089 ,0x9 }, + {0x9008a ,0x3c0 }, + {0x9008b ,0x149 }, + {0x9008c ,0x9 }, + {0x9008d ,0x3c0 }, + {0x9008e ,0x159 }, + {0x9008f ,0x18 }, + {0x90090 ,0x10 }, + {0x90091 ,0x109 }, + {0x90092 ,0x0 }, + {0x90093 ,0x3c0 }, + {0x90094 ,0x109 }, + {0x90095 ,0x18 }, + {0x90096 ,0x4 }, + {0x90097 ,0x48 }, + {0x90098 ,0x18 }, + {0x90099 ,0x4 }, + {0x9009a ,0x58 }, + {0x9009b ,0xa }, + {0x9009c ,0x10 }, + {0x9009d ,0x109 }, + {0x9009e ,0x2 }, + {0x9009f ,0x10 }, + {0x900a0 ,0x109 }, + {0x900a1 ,0x5 }, + {0x900a2 ,0x7c0 }, + {0x900a3 ,0x109 }, + {0x900a4 ,0x10 }, + {0x900a5 ,0x10 }, + {0x900a6 ,0x109 }, + {0x40000 ,0x811 }, + {0x40020 ,0x880 }, + {0x40040 ,0x0 }, + {0x40060 ,0x0 }, + {0x40001 ,0x4008 }, + {0x40021 ,0x83 }, + {0x40041 ,0x4f }, + {0x40061 ,0x0 }, + {0x40002 ,0x4040 }, + {0x40022 ,0x83 }, + {0x40042 ,0x51 }, + {0x40062 ,0x0 }, + {0x40003 ,0x811 }, + {0x40023 ,0x880 }, + {0x40043 ,0x0 }, + {0x40063 ,0x0 }, + {0x40004 ,0x720 }, + {0x40024 ,0xf }, + {0x40044 ,0x1740 }, + {0x40064 ,0x0 }, + {0x40005 ,0x16 }, + {0x40025 ,0x83 }, + {0x40045 ,0x4b }, + {0x40065 ,0x0 }, + {0x40006 ,0x716 }, + {0x40026 ,0xf }, + {0x40046 ,0x2001 }, + {0x40066 ,0x0 }, + {0x40007 ,0x716 }, + {0x40027 ,0xf }, + {0x40047 ,0x2800 }, + {0x40067 ,0x0 }, + {0x40008 ,0x716 }, + {0x40028 ,0xf }, + {0x40048 ,0xf00 }, + {0x40068 ,0x0 }, + {0x40009 ,0x720 }, + {0x40029 ,0xf }, + {0x40049 ,0x1400 }, + {0x40069 ,0x0 }, + {0x4000a ,0xe08 }, + {0x4002a ,0xc15 }, + {0x4004a ,0x0 }, + {0x4006a ,0x0 }, + {0x4000b ,0x623 }, + {0x4002b ,0x15 }, + {0x4004b ,0x0 }, + {0x4006b ,0x0 }, + {0x4000c ,0x4028 }, + {0x4002c ,0x80 }, + {0x4004c ,0x0 }, + {0x4006c ,0x0 }, + {0x4000d ,0xe08 }, + {0x4002d ,0xc1a }, + {0x4004d ,0x0 }, + {0x4006d ,0x0 }, + {0x4000e ,0x623 }, + {0x4002e ,0x1a }, + {0x4004e ,0x0 }, + {0x4006e ,0x0 }, + {0x4000f ,0x4040 }, + {0x4002f ,0x80 }, + {0x4004f ,0x0 }, + {0x4006f ,0x0 }, + {0x40010 ,0x2604 }, + {0x40030 ,0x15 }, + {0x40050 ,0x0 }, + {0x40070 ,0x0 }, + {0x40011 ,0x708 }, + {0x40031 ,0x5 }, + {0x40051 ,0x0 }, + {0x40071 ,0x2002 }, + {0x40012 ,0x8 }, + {0x40032 ,0x80 }, + {0x40052 ,0x0 }, + {0x40072 ,0x0 }, + {0x40013 ,0x2604 }, + {0x40033 ,0x1a }, + {0x40053 ,0x0 }, + {0x40073 ,0x0 }, + {0x40014 ,0x708 }, + {0x40034 ,0xa }, + {0x40054 ,0x0 }, + {0x40074 ,0x2002 }, + {0x40015 ,0x4040 }, + {0x40035 ,0x80 }, + {0x40055 ,0x0 }, + {0x40075 ,0x0 }, + {0x40016 ,0x60a }, + {0x40036 ,0x15 }, + {0x40056 ,0x1200 }, + {0x40076 ,0x0 }, + {0x40017 ,0x61a }, + {0x40037 ,0x15 }, + {0x40057 ,0x1300 }, + {0x40077 ,0x0 }, + {0x40018 ,0x60a }, + {0x40038 ,0x1a }, + {0x40058 ,0x1200 }, + {0x40078 ,0x0 }, + {0x40019 ,0x642 }, + {0x40039 ,0x1a }, + {0x40059 ,0x1300 }, + {0x40079 ,0x0 }, + {0x4001a ,0x4808 }, + {0x4003a ,0x880 }, + {0x4005a ,0x0 }, + {0x4007a ,0x0 }, + {0x900a7 ,0x0 }, + {0x900a8 ,0x790 }, + {0x900a9 ,0x11a }, + {0x900aa ,0x8 }, + {0x900ab ,0x7aa }, + {0x900ac ,0x2a }, + {0x900ad ,0x10 }, + {0x900ae ,0x7b2 }, + {0x900af ,0x2a }, + {0x900b0 ,0x0 }, + {0x900b1 ,0x7c8 }, + {0x900b2 ,0x109 }, + {0x900b3 ,0x10 }, + {0x900b4 ,0x2a8 }, + {0x900b5 ,0x129 }, + {0x900b6 ,0x8 }, + {0x900b7 ,0x370 }, + {0x900b8 ,0x129 }, + {0x900b9 ,0xa }, + {0x900ba ,0x3c8 }, + {0x900bb ,0x1a9 }, + {0x900bc ,0xc }, + {0x900bd ,0x408 }, + {0x900be ,0x199 }, + {0x900bf ,0x14 }, + {0x900c0 ,0x790 }, + {0x900c1 ,0x11a }, + {0x900c2 ,0x8 }, + {0x900c3 ,0x4 }, + {0x900c4 ,0x18 }, + {0x900c5 ,0xe }, + {0x900c6 ,0x408 }, + {0x900c7 ,0x199 }, + {0x900c8 ,0x8 }, + {0x900c9 ,0x8568 }, + {0x900ca ,0x108 }, + {0x900cb ,0x18 }, + {0x900cc ,0x790 }, + {0x900cd ,0x16a }, + {0x900ce ,0x8 }, + {0x900cf ,0x1d8 }, + {0x900d0 ,0x169 }, + {0x900d1 ,0x10 }, + {0x900d2 ,0x8558 }, + {0x900d3 ,0x168 }, + {0x900d4 ,0x70 }, + {0x900d5 ,0x788 }, + {0x900d6 ,0x16a }, + {0x900d7 ,0x1ff8 }, + {0x900d8 ,0x85a8 }, + {0x900d9 ,0x1e8 }, + {0x900da ,0x50 }, + {0x900db ,0x798 }, + {0x900dc ,0x16a }, + {0x900dd ,0x60 }, + {0x900de ,0x7a0 }, + {0x900df ,0x16a }, + {0x900e0 ,0x8 }, + {0x900e1 ,0x8310 }, + {0x900e2 ,0x168 }, + {0x900e3 ,0x8 }, + {0x900e4 ,0xa310 }, + {0x900e5 ,0x168 }, + {0x900e6 ,0xa }, + {0x900e7 ,0x408 }, + {0x900e8 ,0x169 }, + {0x900e9 ,0x6e }, + {0x900ea ,0x0 }, + {0x900eb ,0x68 }, + {0x900ec ,0x0 }, + {0x900ed ,0x408 }, + {0x900ee ,0x169 }, + {0x900ef ,0x0 }, + {0x900f0 ,0x8310 }, + {0x900f1 ,0x168 }, + {0x900f2 ,0x0 }, + {0x900f3 ,0xa310 }, + {0x900f4 ,0x168 }, + {0x900f5 ,0x1ff8 }, + {0x900f6 ,0x85a8 }, + {0x900f7 ,0x1e8 }, + {0x900f8 ,0x68 }, + {0x900f9 ,0x798 }, + {0x900fa ,0x16a }, + {0x900fb ,0x78 }, + {0x900fc ,0x7a0 }, + {0x900fd ,0x16a }, + {0x900fe ,0x68 }, + {0x900ff ,0x790 }, + {0x90100 ,0x16a }, + {0x90101 ,0x8 }, + {0x90102 ,0x8b10 }, + {0x90103 ,0x168 }, + {0x90104 ,0x8 }, + {0x90105 ,0xab10 }, + {0x90106 ,0x168 }, + {0x90107 ,0xa }, + {0x90108 ,0x408 }, + {0x90109 ,0x169 }, + {0x9010a ,0x58 }, + {0x9010b ,0x0 }, + {0x9010c ,0x68 }, + {0x9010d ,0x0 }, + {0x9010e ,0x408 }, + {0x9010f ,0x169 }, + {0x90110 ,0x0 }, + {0x90111 ,0x8b10 }, + {0x90112 ,0x168 }, + {0x90113 ,0x0 }, + {0x90114 ,0xab10 }, + {0x90115 ,0x168 }, + {0x90116 ,0x0 }, + {0x90117 ,0x1d8 }, + {0x90118 ,0x169 }, + {0x90119 ,0x80 }, + {0x9011a ,0x790 }, + {0x9011b ,0x16a }, + {0x9011c ,0x18 }, + {0x9011d ,0x7aa }, + {0x9011e ,0x6a }, + {0x9011f ,0xa }, + {0x90120 ,0x0 }, + {0x90121 ,0x1e9 }, + {0x90122 ,0x8 }, + {0x90123 ,0x8080 }, + {0x90124 ,0x108 }, + {0x90125 ,0xf }, + {0x90126 ,0x408 }, + {0x90127 ,0x169 }, + {0x90128 ,0xc }, + {0x90129 ,0x0 }, + {0x9012a ,0x68 }, + {0x9012b ,0x9 }, + {0x9012c ,0x0 }, + {0x9012d ,0x1a9 }, + {0x9012e ,0x0 }, + {0x9012f ,0x408 }, + {0x90130 ,0x169 }, + {0x90131 ,0x0 }, + {0x90132 ,0x8080 }, + {0x90133 ,0x108 }, + {0x90134 ,0x8 }, + {0x90135 ,0x7aa }, + {0x90136 ,0x6a }, + {0x90137 ,0x0 }, + {0x90138 ,0x8568 }, + {0x90139 ,0x108 }, + {0x9013a ,0xb7 }, + {0x9013b ,0x790 }, + {0x9013c ,0x16a }, + {0x9013d ,0x1f }, + {0x9013e ,0x0 }, + {0x9013f ,0x68 }, + {0x90140 ,0x8 }, + {0x90141 ,0x8558 }, + {0x90142 ,0x168 }, + {0x90143 ,0xf }, + {0x90144 ,0x408 }, + {0x90145 ,0x169 }, + {0x90146 ,0xc }, + {0x90147 ,0x0 }, + {0x90148 ,0x68 }, + {0x90149 ,0x0 }, + {0x9014a ,0x408 }, + {0x9014b ,0x169 }, + {0x9014c ,0x0 }, + {0x9014d ,0x8558 }, + {0x9014e ,0x168 }, + {0x9014f ,0x8 }, + {0x90150 ,0x3c8 }, + {0x90151 ,0x1a9 }, + {0x90152 ,0x3 }, + {0x90153 ,0x370 }, + {0x90154 ,0x129 }, + {0x90155 ,0x20 }, + {0x90156 ,0x2aa }, + {0x90157 ,0x9 }, + {0x90158 ,0x0 }, + {0x90159 ,0x400 }, + {0x9015a ,0x10e }, + {0x9015b ,0x8 }, + {0x9015c ,0xe8 }, + {0x9015d ,0x109 }, + {0x9015e ,0x0 }, + {0x9015f ,0x8140 }, + {0x90160 ,0x10c }, + {0x90161 ,0x10 }, + {0x90162 ,0x8138 }, + {0x90163 ,0x10c }, + {0x90164 ,0x8 }, + {0x90165 ,0x7c8 }, + {0x90166 ,0x101 }, + {0x90167 ,0x8 }, + {0x90168 ,0x0 }, + {0x90169 ,0x8 }, + {0x9016a ,0x8 }, + {0x9016b ,0x448 }, + {0x9016c ,0x109 }, + {0x9016d ,0xf }, + {0x9016e ,0x7c0 }, + {0x9016f ,0x109 }, + {0x90170 ,0x0 }, + {0x90171 ,0xe8 }, + {0x90172 ,0x109 }, + {0x90173 ,0x47 }, + {0x90174 ,0x630 }, + {0x90175 ,0x109 }, + {0x90176 ,0x8 }, + {0x90177 ,0x618 }, + {0x90178 ,0x109 }, + {0x90179 ,0x8 }, + {0x9017a ,0xe0 }, + {0x9017b ,0x109 }, + {0x9017c ,0x0 }, + {0x9017d ,0x7c8 }, + {0x9017e ,0x109 }, + {0x9017f ,0x8 }, + {0x90180 ,0x8140 }, + {0x90181 ,0x10c }, + {0x90182 ,0x0 }, + {0x90183 ,0x1 }, + {0x90184 ,0x8 }, + {0x90185 ,0x8 }, + {0x90186 ,0x4 }, + {0x90187 ,0x8 }, + {0x90188 ,0x8 }, + {0x90189 ,0x7c8 }, + {0x9018a ,0x101 }, + {0x90006 ,0x0 }, + {0x90007 ,0x0 }, + {0x90008 ,0x8 }, + {0x90009 ,0x0 }, + {0x9000a ,0x0 }, + {0x9000b ,0x0 }, + {0xd00e7 ,0x400 }, + {0x90017 ,0x0 }, + {0x9001f ,0x2a }, + {0x90026 ,0x6a }, + {0x400d0 ,0x0 }, + {0x400d1 ,0x101 }, + {0x400d2 ,0x105 }, + {0x400d3 ,0x107 }, + {0x400d4 ,0x10f }, + {0x400d5 ,0x202 }, + {0x400d6 ,0x20a }, + {0x400d7 ,0x20b }, + {0x2003a ,0x2 }, + {0x2000b ,0x5d }, + {0x2000c ,0xbb }, + {0x2000d ,0x753 }, + {0x2000e ,0x2c }, + {0x12000b ,0xc }, + {0x12000c ,0x19 }, + {0x12000d ,0xfa }, + {0x12000e ,0x10 }, + {0x22000b ,0x3 }, + {0x22000c ,0x6 }, + {0x22000d ,0x3e }, + {0x22000e ,0x10 }, + {0x9000c ,0x0 }, + {0x9000d ,0x173 }, + {0x9000e ,0x60 }, + {0x9000f ,0x6110 }, + {0x90010 ,0x2152 }, + {0x90011 ,0xdfbd }, + {0x90012 ,0x60 }, + {0x90013 ,0x6152 }, + {0x20010 ,0x5a }, + {0x20011 ,0x3 }, + {0x120010 ,0x5a }, + {0x120011 ,0x3 }, + {0x220010 ,0x5a }, + {0x220011 ,0x3 }, + {0x40080 ,0xe0 }, + {0x40081 ,0x12 }, + {0x40082 ,0xe0 }, + {0x40083 ,0x12 }, + {0x40084 ,0xe0 }, + {0x40085 ,0x12 }, + {0x140080 ,0xe0 }, + {0x140081 ,0x12 }, + {0x140082 ,0xe0 }, + {0x140083 ,0x12 }, + {0x140084 ,0xe0 }, + {0x140085 ,0x12 }, + {0x240080 ,0xe0 }, + {0x240081 ,0x12 }, + {0x240082 ,0xe0 }, + {0x240083 ,0x12 }, + {0x240084 ,0xe0 }, + {0x240085 ,0x12 }, + {0x400fd ,0xf }, + {0x10011 ,0x1 }, + {0x10012 ,0x1 }, + {0x10013 ,0x180 }, + {0x10018 ,0x1 }, + {0x10002 ,0x6209 }, + {0x100b2 ,0x1 }, + {0x101b4 ,0x1 }, + {0x102b4 ,0x1 }, + {0x103b4 ,0x1 }, + {0x104b4 ,0x1 }, + {0x105b4 ,0x1 }, + {0x106b4 ,0x1 }, + {0x107b4 ,0x1 }, + {0x108b4 ,0x1 }, + {0x11011 ,0x1 }, + {0x11012 ,0x1 }, + {0x11013 ,0x180 }, + {0x11018 ,0x1 }, + {0x11002 ,0x6209 }, + {0x110b2 ,0x1 }, + {0x111b4 ,0x1 }, + {0x112b4 ,0x1 }, + {0x113b4 ,0x1 }, + {0x114b4 ,0x1 }, + {0x115b4 ,0x1 }, + {0x116b4 ,0x1 }, + {0x117b4 ,0x1 }, + {0x118b4 ,0x1 }, + {0x12011 ,0x1 }, + {0x12012 ,0x1 }, + {0x12013 ,0x180 }, + {0x12018 ,0x1 }, + {0x12002 ,0x6209 }, + {0x120b2 ,0x1 }, + {0x121b4 ,0x1 }, + {0x122b4 ,0x1 }, + {0x123b4 ,0x1 }, + {0x124b4 ,0x1 }, + {0x125b4 ,0x1 }, + {0x126b4 ,0x1 }, + {0x127b4 ,0x1 }, + {0x128b4 ,0x1 }, + {0x13011 ,0x1 }, + {0x13012 ,0x1 }, + {0x13013 ,0x180 }, + {0x13018 ,0x1 }, + {0x13002 ,0x6209 }, + {0x130b2 ,0x1 }, + {0x131b4 ,0x1 }, + {0x132b4 ,0x1 }, + {0x133b4 ,0x1 }, + {0x134b4 ,0x1 }, + {0x135b4 ,0x1 }, + {0x136b4 ,0x1 }, + {0x137b4 ,0x1 }, + {0x138b4 ,0x1 }, + {0x2003a ,0x2 }, + {0xc0080 ,0x2 }, + {0xd0000 ,0x1 } +}; + +struct dram_fsp_msg ddr_dram_fsp_msg[] = { + { +/* P0 3000mts 1D */ + .drate =3000 , + .fw_type =FW_1D_IMAGE , + .fsp_cfg = ddr_fsp0_cfg, + .fsp_cfg_num =ARRAY_SIZE (ddr_fsp0_cfg), + }, + { +/* P1 400mts 1D */ + .drate =400 , + .fw_type =FW_1D_IMAGE , + .fsp_cfg = ddr_fsp1_cfg, + .fsp_cfg_num =ARRAY_SIZE (ddr_fsp1_cfg), + }, + { +/* P2 100mts 1D */ + .drate =100 , + .fw_type =FW_1D_IMAGE , + .fsp_cfg = ddr_fsp2_cfg, + .fsp_cfg_num =ARRAY_SIZE (ddr_fsp2_cfg), + }, + { +/* P0 3000mts 2D */ + .drate =3000 , + .fw_type =FW_2D_IMAGE , + .fsp_cfg = ddr_fsp0_2d_cfg, + .fsp_cfg_num =ARRAY_SIZE (ddr_fsp0_2d_cfg), + }, +}; + +/* ddr timing config params */ +struct dram_timing_info dram_timing = { + .ddrc_cfg = ddr_ddrc_cfg, + .ddrc_cfg_num =ARRAY_SIZE (ddr_ddrc_cfg), + .ddrphy_cfg = ddr_ddrphy_cfg, + .ddrphy_cfg_num =ARRAY_SIZE (ddr_ddrphy_cfg), + .fsp_msg = ddr_dram_fsp_msg, + .fsp_msg_num =ARRAY_SIZE (ddr_dram_fsp_msg), + .ddrphy_trained_csr = ddr_ddrphy_trained_csr, + .ddrphy_trained_csr_num =ARRAY_SIZE (ddr_ddrphy_trained_csr), + .ddrphy_pie = ddr_phy_pie, + .ddrphy_pie_num =ARRAY_SIZE (ddr_phy_pie), + .fsp_table = {3000 ,400 ,100 , }, +}; +board/toradex/verdin-imx8mm/spl.c new file +16
-0@@ -0,0 +1,183 @@ +// SPDX-License-Identifier: GPL-2.0+ +/* +* Copyright 2019 Toradex AG +*/ + +#include <common.h> +#include <cpu_func.h> +#include <hang.h> +#include <spl.h> + +#include <asm/io.h> +#include <asm/mach-imx/iomux-v3.h> +#include <asm/arch/clock.h> +#include <asm/arch/imx8mm_pins.h> +#include <asm/arch/sys_proto.h> +#include <asm/mach-imx/boot_mode.h>
board/toradex/verdin-imx8mm/spl.c line 26
Quoted 10 lines
board/toradex/verdin-imx8mm/spl.c new file +10
-0+#include <asm/arch/ddr.h> + +#include <dm/uclass.h> +#include <dm/device.h> +#include <dm/uclass-internal.h> +#include <dm/device-internal.h> + +#include <power/pmic.h> +#include <power/bd71837.h> +
I prefer header files to be alphabetically ordered.
board/toradex/verdin-imx8mm/verdin-imx8mm.c
Quoted 190 lines
board/toradex/verdin-imx8mm/spl.c new file +46
-0+DECLARE_GLOBAL_DATA_PTR ; + +int spl_board_boot_device (enum boot_device boot_dev_spl) +{ +switch (boot_dev_spl) { +case MMC1_BOOT : +return BOOT_DEVICE_MMC1 ; +case SD2_BOOT : +case MMC2_BOOT : +return BOOT_DEVICE_MMC2 ; +case SD3_BOOT : +case MMC3_BOOT : +return BOOT_DEVICE_MMC1 ; +case USB_BOOT : +return BOOT_DEVICE_BOARD ; +default : +return BOOT_DEVICE_NONE ; + } +} + +void spl_dram_init (void ) +{ +ddr_init (&dram_timing); +} + +void spl_board_init (void ) +{ +/* Serial download mode */ +if (is_usb_boot ()) { +puts ("Back to ROM, SDP\n" ); +restore_boot_params (); + } +puts ("Normal Boot\n" ); +} + +#ifdef CONFIG_SPL_LOAD_FIT +int board_fit_config_name_match (const char *name) +{ +/* Just empty function now - can't decide what to choose */ +debug ("%s: %s\n" , __func__, name); + +return 0 ; +} +#endif + +#define UART_PAD_CTRL (PAD_CTL_PUE | PAD_CTL_PE |
PAD_CTL_DSE4)
+#defineWDOG_PAD_CTRL(PAD_CTL_DSE6|PAD_CTL_ODE|PAD_CTL_PUE|PAD_CTL_PE)board/toradex/verdin-imx8mm/spl.c new file +9
-0+ +/* Verdin UART_3, Console/Debug UART */ +static iomux_v3_cfg_t const uart_pads[] = { +IMX8MM_PAD_SAI2_RXFS_UART1_TX |MUX_PAD_CTRL (UART_PAD_CTRL ), +IMX8MM_PAD_SAI2_RXC_UART1_RX |MUX_PAD_CTRL (UART_PAD_CTRL ), +}; + +static iomux_v3_cfg_t const wdog_pads[] = { + IMX8MM_PAD_GPIO1_IO02_WDOG1_WDOG_B |
MUX_PAD_CTRL(WDOG_PAD_CTRL),board/toradex/verdin-imx8mm/spl.c new file +7
-0+}; + +int board_early_init_f (void ) +{ +struct wdog_regs *wdog = (struct wdog_regs *)WDOG1_BASE_ADDR ; + + imx_iomux_v3_setup_multiple_pads(wdog_pads,
ARRAY_SIZE(wdog_pads));board/toradex/verdin-imx8mm/spl.c new file +4
-0+ +set_wdog_reset (wdog); + + imx_iomux_v3_setup_multiple_pads(uart_pads,
ARRAY_SIZE(uart_pads));board/toradex/verdin-imx8mm/spl.c new file +18
-0+ +return 0 ; +} + +int power_init_board (void ) +{ +struct udevice *dev; +int ret; + + ret =pmic_get ("pmic at 4b" , &dev); +if (ret == -ENODEV ) { +puts ("No pmic\n" ); +return 0 ; + } +if (ret !=0 ) +return ret; + +/* decrease RESET key long push time from the default 10s to 10ms */
board/toradex/verdin-imx8mm/spl.c new file +6
-0+pmic_reg_write (dev,BD718XX_PWRONCONFIG1 ,0x0 ); + +/* unlock the PMIC regs */ +pmic_reg_write (dev,BD718XX_REGLOCK ,0x1 );Lines of this file are not shown. View the raw message.
The rest of this diff is not shown. View the raw message.
access */
board/toradex/verdin-imx8mm/spl.c new file +45
-0Lines of this file are not shown. View the raw message.
The rest of this diff is not shown. View the raw message.
tree\n");
board/toradex/verdin-imx8mm/spl.c new file +14
-0Lines of this file are not shown. View the raw message.
The rest of this diff is not shown. View the raw message.
argv[])
board/toradex/verdin-imx8mm/spl.c new file +7
-0Lines of this file are not shown. View the raw message.
board/toradex/verdin-imx8mm/verdin-imx8mm.c new file +17
-0Lines of this file are not shown. View the raw message.
The rest of this diff is not shown. View the raw message.
Wondering whether or not this could be taken from the DDR controller's configured size as on i.MX 6/7.
include/configs/verdin-imx8mm.h
Quoted 232 lines
board/toradex/verdin-imx8mm/verdin-imx8mm.c new file +57
-0Lines of this file are not shown. View the raw message.
configs/verdin- renamed from configs/verdin-imx8mm_defconfig +0
-0The rest of this diff is not shown. View the raw message.
imx8mm_defconfig
new file mode 100644
index 0000000000..87fbed8456configs/verdin-imx8mm_defconfig new file +28
-0Lines of this file are not shown. View the raw message.
The rest of this diff is not shown. View the raw message.
imx8mm/imximage.cfg"
configs/verdin-imx8mm_defconfig new file +60
-0Lines of this file are not shown. View the raw message.
include/configs/verdin-imx8mm.h new file +22
-0Lines of this file are not shown. View the raw message.
The rest of this diff is not shown. View the raw message.
512)
include/configs/verdin-imx8mm.h new file +49
-0Lines of this file are not shown. View the raw message.
The rest of this diff is not shown. View the raw message.
Quite minimalistic. At least the update_uboot wrapper similar to the one found in Apalis iMX8 resp. Colibri iMX8X could be added.
include/configs/verdin-imx8mm.h
Quoted 52 lines
include/configs/verdin-imx8mm.h new file +11
-0Lines of this file are not shown. View the raw message.
The rest of this diff is not shown. View the raw message.
USDHC2 */
include/configs/verdin-imx8mm.h new file +11
-0Lines of this file are not shown. View the raw message.
The rest of this diff is not shown. View the raw message.
RT + \
include/configs/verdin-imx8mm.h new file +28
-0Lines of this file are not shown. View the raw message.
The rest of this diff is not shown. View the raw message.
Test looks good. Thanks!
Cheers
Marcel
Part of the diff is not shown here. View the raw message.
PATCH 4/5 board: toradex: verdin-imx8mm: add README
In reply to Igor OpaniukFrom: Igor Opaniuk <[email protected]>
Add README with build steps for U-boot and TF-A for Verdin i.MX8MM SoM.
---
board/toradex/verdin-imx8mm/README | 81 ++++++++++++++++++++++++++++++ 1 file changed, 81 insertions(+) create mode 100644 board/toradex/verdin-imx8mm/README
board/toradex/verdin-imx8mm/README new file +81 -0
@@ -0,0 +1,81 @@ +U-Boot for the Toradex Verdin i.MX8MM board + +Quick Start +=========== +- Build the ARM Trusted firmware binary +- Get DDR firmware +- Build U-Boot +- Flash to eMMC +- Boot + + +Get and Build the ARM Trusted firmware (Trusted Firmware A) +====================================== +$ echo "Downloading and building TF-A..." +$ git clone -b imx_4.14.78_1.0.0_ga https://source.codeaurora.org/external/imx/imx-atf +$ cd imx-atf + +Please edit `plat/imx/imx8mm/include/platform_def.h` so it +contains proper values for UART configuration and BL31 base +address (correct values listed below): +#define BL31_BASE 0x910000 +#define IMX_BOOT_UART_BASE 0x30860000 +#define DEBUG_CONSOLE 1 + +Then build ATF (TF-A): +$ make PLAT=imx8mm bl31 + +Get the DDR firmware +============================= +$ wget https://www.nxp.com/lgfiles/NMG/MAD/YOCTO/firmware-imx-8.1.1.bin +$ chmod +x firmware-imx-8.1.1.bin +$ ./firmware-imx-8.1.1.bin +$ cp firmware-imx-8.1.1/firmware/ddr/synopsys/lpddr4*.bin ./ + +Build U-Boot +============ +$ export CROSS_COMPILE=aarch64-poky-linux- +$ make verdin-imx8mm_defconfig +$ make flash.bin + +Flash to eMMC +=========== +> tftpboot ${loadaddr} flash.bin +> setexpr blkcnt ${filesize} + 0x1ff && setexpr blkcnt ${blkcnt} / 0x200 +> mmc dev 0 1 && mmc write ${loadaddr} 0x2 ${blkcnt} + +Boot +=========== + +ATF, U-boot proper and u-boot.dtb images are packed into FIT image, +which is loaded and parsed by SPL. + +Boot sequence is: +SPL ---> ATF (TF-A) ---> U-boot proper + +Output: + +U-Boot SPL 2020.01-01840-gd92bdc79cf-dirty (Jan 22 2020 - 18:50:57 +0200) +Normal Boot +Trying to boot from MMC1 +NOTICE: Configuring TZASC380 +NOTICE: RDC off +NOTICE: BL31: v1.5(release):p9.0.0_1.1.0-ga-20190801-0-gd6451cc1e-dirty +NOTICE: BL31: Built : 17:43:07, Jan 22 2020 +NOTICE: sip svc init + + +U-Boot 2020.01-01840-gd92bdc79cf-dirty (Jan 22 2020 - 18:50:57 +0200) + +CPU: Freescale i.MX8MMQ rev1.0 at 0 MHz +Reset cause: POR +DRAM: 2 GiB +MMC: FSL_SDHC: 0, FSL_SDHC: 1 +Loading Environment from MMC... OK +In: serial +Out: serial +Err: serial +Model: Toradex Verdin iMX8M Mini 2GB Wi-Fi / BT IT V1.0A, Serial# 06535148 +Net: Could not get PHY for FEC0: addr 7 +eth0: ethernet at 30be0000 +Hit any key to stop autoboot: 0
Signature · 1 line
2.17.1
PATCH 4/5 board: toradex: verdin-imx8mm: add README
Quoted 6 lines · Igor Opaniuk
From: Igor Opaniuk <[email protected]>
Add README with build steps for U-boot and TF-A for Verdin i.MX8MM SoM.
Signed-off-by Igor Opaniuk <[email protected]>
Quoted 96 lines
---
board/toradex/verdin-imx8mm/README | 81 ++++++++++++++++++++++++++++++ 1 file changed, 81 insertions(+) create mode 100644 board/toradex/verdin-imx8mm/READMEboard/toradex/verdin-imx8mm/README new file +81
-1@@ -0,0 +1,81 @@ +U-Boot for the Toradex Verdin i.MX8MM board + +Quick Start +=========== +- Build the ARM Trusted firmware binary +- Get DDR firmware +- Build U-Boot +- Flash to eMMC +- Boot + + +Get and Build the ARM Trusted firmware (Trusted Firmware A) +====================================== +$ echo "Downloading and building TF-A..." +$ git clone -b imx_4.14.78_1.0.0_ga https://source.codeaurora.org/external/imx/imx-atf +$ cd imx-atf + +Please edit `plat/imx/imx8mm/include/platform_def.h` so it +contains proper values for UART configuration and BL31 base +address (correct values listed below): +#define BL31_BASE 0x910000 +#define IMX_BOOT_UART_BASE 0x30860000 +#define DEBUG_CONSOLE 1 + +Then build ATF (TF-A): +$ make PLAT=imx8mm bl31 + +Get the DDR firmware +============================= +$ wget https://www.nxp.com/lgfiles/NMG/MAD/YOCTO/firmware-imx-8.1.1.bin +$ chmod +x firmware-imx-8.1.1.bin +$ ./firmware-imx-8.1.1.bin +$ cp firmware-imx-8.1.1/firmware/ddr/synopsys/lpddr4*.bin ./ + +Build U-Boot +============ +$ export CROSS_COMPILE=aarch64-poky-linux- +$ make verdin-imx8mm_defconfig +$ make flash.bin + +Flash to eMMC +=========== +> tftpboot ${loadaddr} flash.bin +> setexpr blkcnt ${filesize} + 0x1ff && setexpr blkcnt ${blkcnt} / 0x200 +> mmc dev 0 1 && mmc write ${loadaddr} 0x2 ${blkcnt} + +Boot +=========== + +ATF, U-boot proper and u-boot.dtb images are packed into FIT image, +which is loaded and parsed by SPL. + +Boot sequence is: +SPL ---> ATF (TF-A) ---> U-boot proper + +Output: + +U-Boot SPL 2020.01-01840-gd92bdc79cf-dirty (Jan 22 2020 - 18:50:57 +0200) +Normal Boot +Trying to boot from MMC1 +NOTICE: Configuring TZASC380 +NOTICE: RDC off +NOTICE: BL31: v1.5(release):p9.0.0_1.1.0-ga-20190801-0-gd6451cc1e-dirty +NOTICE: BL31: Built : 17:43:07, Jan 22 2020 +NOTICE: sip svc init + + +U-Boot 2020.01-01840-gd92bdc79cf-dirty (Jan 22 2020 - 18:50:57 +0200) + +CPU: Freescale i.MX8MMQ rev1.0 at 0 MHz +Reset cause: POR +DRAM: 2 GiB +MMC: FSL_SDHC: 0, FSL_SDHC: 1 +Loading Environment from MMC... OK +In: serial +Out: serial +Err: serial +Model: Toradex Verdin iMX8M Mini 2GB Wi-Fi / BT IT V1.0A, Serial# 06535148 +Net: Could not get PHY for FEC0: addr 7 +eth0: ethernet at 30be0000 +Hit any key to stop autoboot: 0 --2.17.1
Signature · 6 lines
Best regards Oleksandr Suvorov Toradex AG Altsagenstrasse 5 | 6048 Horw/Luzern | Switzerland | T: +41 41 500 4800 (main line)
PATCH 4/5 board: toradex: verdin-imx8mm: add README
In reply to Igor OpaniukHi Igor
Quoted 21 lines · Igor Opaniuk
From: Igor Opaniuk <[email protected]>
Add README with build steps for U-boot and TF-A for Verdin i.MX8MM SoM.
Signed-off-by Igor Opaniuk <[email protected]>Reviewed-by Oleksandr Suvorov <[email protected]>---
board/toradex/verdin-imx8mm/README | 81 ++++++++++++++++++++++++++++++ 1 file changed, 81 insertions(+) create mode 100644 board/toradex/verdin-imx8mm/READMEboard/toradex/verdin-imx8mm/README new file +0
-0
board/toradex/verdin-imx8mm/README line 1
Quoted 1 line
board/toradex/verdin-imx8mm/README new file +1
-0@@ -0,0 +1,81 @@ +U-Boot for the Toradex Verdin i.MX8MM board
Verdin iMX8M Mini Module
Quoted 4 lines
board/toradex/verdin-imx8mm/README new file +4
-0+ +Quick Start +=========== +- Build the ARM Trusted firmware binary
board/toradex/verdin-imx8mm/README
Quoted 10 lines
board/toradex/verdin-imx8mm/README new file +10
-0+- Get DDR firmware +- Build U-Boot +- Flash to eMMC +- Boot + + +Get and Build the ARM Trusted firmware (Trusted Firmware A) +====================================== +$ echo "Downloading and building TF-A..." +$ git clone -b imx_4.14.78_1.0.0_ga
I suggest to use the later branch imx_4.14.98_2.3.0 which should also include i.MX 8M Nano support now.
Quoted 16 lines
https://source.codeaurora.org/external/imx/imx-atf
+$ cd imx-atfboard/toradex/verdin-imx8mm/README new file +14
-0+ +Please edit `plat/imx/imx8mm/include/platform_def.h` so it +contains proper values for UART configuration and BL31 base +address (correct values listed below): +#define BL31_BASE 0x910000 +#define IMX_BOOT_UART_BASE 0x30860000 +#define DEBUG_CONSOLE 1 + +Then build ATF (TF-A): +$ make PLAT=imx8mm bl31 + +Get the DDR firmware +============================= +$ wget
There is now 8.4.1 available from above mentioned release. However, I believe there were no changes in DDR firmware.
board/toradex/verdin-imx8mm/README line 37
Quoted 7 lines
+$ chmod +x firmware-imx-8.1.1.bin
+$ ./firmware-imx-8.1.1.bin
+$ cp firmware-imx-8.1.1/firmware/ddr/synopsys/lpddr4*.bin ./board/toradex/verdin-imx8mm/README new file +4
-0+ +Build U-Boot +============ +$ export CROSS_COMPILE=aarch64-poky-linux-
With a linaro toolchain this would rather be:
aarch64-linux-gnu-
Quoted 9 lines
+$ make verdin-imx8mm_defconfig
+$ make flash.binboard/toradex/verdin-imx8mm/README new file +5
-0+ +Flash to eMMC +=========== +> tftpboot ${loadaddr} flash.bin +> setexpr blkcnt ${filesize} + 0x1ff && setexpr blkcnt ${blkcnt} /
0x200
+> mmc dev 0 1 && mmc write ${loadaddr}0x2${blkcnt}
Or just run update_uboot (;-p).
Quoted 37 lines
board/toradex/verdin-imx8mm/README new file +19
-0+ +Boot +=========== + +ATF, U-boot proper and u-boot.dtb images are packed into FIT image, +which is loaded and parsed by SPL. + +Boot sequence is: +SPL ---> ATF (TF-A) ---> U-boot proper + +Output: + +U-Boot SPL 2020.01-01840-gd92bdc79cf-dirty (Jan 22 2020 - 18:50:57 +0200) +Normal Boot +Trying to boot from MMC1 +NOTICE: Configuring TZASC380 +NOTICE: RDC off +NOTICE: BL31: v1.5(release):p9.0.0_1.1.0-ga-20190801-0-gd6451cc1e-dirty
board/toradex/verdin-imx8mm/README new file +16
-0+NOTICE: BL31: Built : 17:43:07, Jan 22 2020 +NOTICE: sip svc init + + +U-Boot 2020.01-01840-gd92bdc79cf-dirty (Jan 22 2020 - 18:50:57 +0200) + +CPU: Freescale i.MX8MMQ rev1.0 at 0 MHz +Reset cause: POR +DRAM: 2 GiB +MMC: FSL_SDHC: 0, FSL_SDHC: 1 +Loading Environment from MMC... OK +In: serial +Out: serial +Err: serial +Model: Toradex Verdin iMX8M Mini 2GB Wi-Fi / BT IT V1.0A, Serial#06535148
board/toradex/verdin-imx8mm/README line 81
Quoted 3 lines
board/toradex/verdin-imx8mm/README new file +3
-0+Net: Could not get PHY for FEC0: addr 7 +eth0: ethernet at 30be0000 +Hit any key to stop autoboot: 0
Cheers
Marcel
PATCH 5/5 board: toradex: verdin-imx8mm: add MAINTAINERS
In reply to Igor OpaniukFrom: Igor Opaniuk <[email protected]>
Assign Igor Opaniuk as a board maintainer.
---
board/toradex/verdin-imx8mm/MAINTAINERS | 9 +++++++++ 1 file changed, 9 insertions(+) create mode 100644 board/toradex/verdin-imx8mm/MAINTAINERS
board/toradex/verdin-imx8mm/MAINTAINERS new file +9 -0
@@ -0,0 +1,9 @@ +Verdin iMX8MM +M: Igor Opaniuk <[email protected]> +W: https://www.toradex.com/computer-on-modules/verdin-arm-family/nxp-imx-8m-mini +S: Maintained +F: arch/arm/dts/imx8mm-verdin.dts +F: arch/arm/dts/imx8mm-verdin-u-boot.dtsi +F: board/toradex/verdin-imx8mm/ +F: configs/verdin-imx8mm_defconfig +F: include/configs/verdin-imx8mm.h
Signature · 1 line
2.17.1
PATCH 5/5 board: toradex: verdin-imx8mm: add MAINTAINERS
Quoted 6 lines · Igor Opaniuk
From: Igor Opaniuk <[email protected]>
Assign Igor Opaniuk as a board maintainer.
Signed-off-by Igor Opaniuk <[email protected]>
Quoted 24 lines
---
board/toradex/verdin-imx8mm/MAINTAINERS | 9 +++++++++ 1 file changed, 9 insertions(+) create mode 100644 board/toradex/verdin-imx8mm/MAINTAINERSboard/toradex/verdin-imx8mm/MAINTAINERS new file +9
-1@@ -0,0 +1,9 @@ +Verdin iMX8MM +M: Igor Opaniuk <[email protected]> +W: https://www.toradex.com/computer-on-modules/verdin-arm-family/nxp-imx-8m-mini +S: Maintained +F: arch/arm/dts/imx8mm-verdin.dts +F: arch/arm/dts/imx8mm-verdin-u-boot.dtsi +F: board/toradex/verdin-imx8mm/ +F: configs/verdin-imx8mm_defconfig +F: include/configs/verdin-imx8mm.h --2.17.1
Signature · 6 lines
Best regards Oleksandr Suvorov Toradex AG Altsagenstrasse 5 | 6048 Horw/Luzern | Switzerland | T: +41 41 500 4800 (main line)
PATCH 5/5 board: toradex: verdin-imx8mm: add MAINTAINERS
In reply to Igor OpaniukHi Igor
Quoted 19 lines · Igor Opaniuk
From: Igor Opaniuk <[email protected]>
Assign Igor Opaniuk as a board maintainer.
Signed-off-by Igor Opaniuk <[email protected]>Reviewed-by Oleksandr Suvorov <[email protected]>---
board/toradex/verdin-imx8mm/MAINTAINERS | 9 +++++++++ 1 file changed, 9 insertions(+) create mode 100644 board/toradex/verdin-imx8mm/MAINTAINERSboard/toradex/verdin-imx8mm/MAINTAINERS new file +0
-0
board/toradex/verdin-imx8mm/MAINTAINERS line 1
Quoted 1 line
board/toradex/verdin-imx8mm/MAINTAINERS new file +1
-0@@ -0,0 +1,9 @@ +Verdin iMX8MM
Here we should use the longer marketing name:
Verdin iMX8M Mini
board/toradex/verdin-imx8mm/MAINTAINERS line 9
Quoted 9 lines
board/toradex/verdin-imx8mm/MAINTAINERS new file +2
-0+M: Igor Opaniuk <[email protected]> +W:https://www.toradex.com/computer-on-modules/verdin-arm-family/nxp-imx-8m-mini
board/toradex/verdin-imx8mm/MAINTAINERS new file +6
-0+S: Maintained +F: arch/arm/dts/imx8mm-verdin.dts +F: arch/arm/dts/imx8mm-verdin-u-boot.dtsi +F: board/toradex/verdin-imx8mm/ +F: configs/verdin-imx8mm_defconfig +F: include/configs/verdin-imx8mm.h
Cheers
Marcel
cover board: toradex: add Verdin iMX8MM 2GB WB IT v1.0a
In reply to Igor OpaniukHi Igor
BTW: Enjoy your well deserved vacation. I will pick it up and send a v2 don't worry (;-p).
Quoted 3 lines · Igor Opaniuk
This add initial minimal support for the Toradex Verdin iMX8MM 2GB WB IT
V1.0A module.
We just got the final SKU naming update and this one will be called Toradex Verdin iMX8M Mini Quad 2GB WB IT V1.0A.
Quoted 4 lines
They are now strapped to boot from eFuses which are factory fused to properly boot from their on-module eMMC. U-Boot supports booting from the on-module eMMC only, SDP support is disabled for now.
Due to missing i.MX 8M Mini USB support that is.
Quoted 2 lines
Functionality wise the following is known to be working:
- eMMC, 8-bit and 4-bit MMC/SD card slots
Note that while the eMMC is 8-bit the boot ROM only supports booting in a 4-bit configuration. Thank you NXP!
Quoted 66 lines
- Ethernet
- GPIOs
- I2CBoot sequence is:
SPL ---> ATF (TF-A) ---> U-boot properATF, U-boot proper and u-boot.dtb images are packed into FIT image, loaded by SPL.
Boot:
U-Boot SPL 2020.01-01840-gd92bdc79cf-dirty (Jan 22 2020 - 18:50:57 +0200)
Normal Boot
Trying to boot from MMC1U-Boot 2020.01-01840-gd92bdc79cf-dirty (Jan 22 2020 - 18:50:57 +0200)
CPU: Freescale i.MX8MMQ rev1.0 at 0 MHz Reset cause: POR DRAM: 2 GiB MMC: FSL_SDHC: 0, FSL_SDHC: 1 Loading Environment from MMC... OK In: serial Out: serial Err: serial Model: Toradex Verdin iMX8M Mini 2GB Wi-Fi / BT IT V1.0A, Serial# 06535148 Net: Could not get PHY for FEC0: addr 7 eth0: ethernet at 30be0000 Hit any key to stop autoboot: 0Igor Opaniuk (3):
board: toradex: add Verdin iMX8MM 2GB WB IT v1.0a
board: toradex: verdin-imx8mm: add README
board: toradex: verdin-imx8mm: addMAINTAINERSMarcel Ziswiler (1):
toradex: tdx-cfg-block: add Verdin i.MX8MM supportMax Krummenacher (1):
dt-bindings: pinctrl: imx8mm: add alternative uart muxingsarch/arm/dts/Makefile | 3 +- arch/arm/dts/imx8mm-pinfunc.h | 21 + arch/arm/dts/imx8mm-verdin-u-boot.dtsi | 103 ++ arch/arm/dts/imx8mm-verdin.dts | 854 +++++++++ arch/arm/mach-imx/imx8m/Kconfig | 7 + board/toradex/common/tdx-cfg-block.c | 17 +- board/toradex/common/tdx-cfg-block.h | 1 + board/toradex/verdin-imx8mm/Kconfig | 30 + board/toradex/verdin-imx8mm/MAINTAINERS | 9 + board/toradex/verdin-imx8mm/Makefile | 12 + board/toradex/verdin-imx8mm/README | 81 + board/toradex/verdin-imx8mm/imximage.cfg | 16 + board/toradex/verdin-imx8mm/lpddr4_timing.c | 1851 +++++++++++++++++++ board/toradex/verdin-imx8mm/spl.c | 183 ++ board/toradex/verdin-imx8mm/verdin-imx8mm.c | 74 + configs/verdin-imx8mm_defconfig | 88 + include/configs/verdin-imx8mm.h | 121 ++ 17 files changed, 3468 insertions(+), 3 deletions(-) create mode 100644 arch/arm/dts/imx8mm-verdin-u-boot.dtsi create mode 100644 arch/arm/dts/imx8mm-verdin.dts create mode 100644 board/toradex/verdin-imx8mm/Kconfig create mode 100644 board/toradex/verdin-imx8mm/MAINTAINERS
Quoted 8 lines
create mode 100644 board/toradex/verdin-imx8mm/Makefile create mode 100644 board/toradex/verdin-imx8mm/README create mode 100644 board/toradex/verdin-imx8mm/imximage.cfg create mode 100644 board/toradex/verdin-imx8mm/lpddr4_timing.c create mode 100644 board/toradex/verdin-imx8mm/spl.c create mode 100644 board/toradex/verdin-imx8mm/verdin-imx8mm.c create mode 100644 configs/verdin-imx8mm_defconfig create mode 100644 include/configs/verdin-imx8mm.h
Cheers
Marcel
cover board: toradex: add Verdin iMX8MM 2GB WB IT v1.0a
Hi Marcel,
Quoted 7 lines · Marcel Ziswiler
Hi Igor
Quoted 4 lines
They are now strapped to boot from eFuses which are factory fused to properly boot from their on-module eMMC. U-Boot supports booting from the on-module eMMC only, SDP support is disabled for now.
Quoted 8 lines
Due to missing i.MX 8M Mini USB support that is.
Quoted 2 lines
Functionality wise the following is known to be working:
- eMMC, 8-bit and 4-bit MMC/SD card slotsNote that while the eMMC is 8-bit the boot ROM only supports booting in a 4-bit configuration. Thank you NXP!
Sarcasm ? :-P
Stefano
Signature · 5 lines
===================================================================== DENX Software Engineering GmbH, Managing Director: Wolfgang Denk HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany Phone: +49-8142-66989-53 Fax: +49-8142-66989-80 Email: sbabic at denx.de =====================================================================