J721e: Add support for DFU boot mode
Subsystems (2)
cover J721e: Add support for DFU boot mode
This series adds support to boot via USB DFU mode.
Vignesh Raghavendra (7):
arm: mach-k3: j721e: Rename BOOT_DEVICE_USB to BOOT_DEVICE_DFU
arm: mach-k3: sysfw-loader: Add support to download SYSFW via DFU
arm: dts: k3-j721e-common-proc-board: Enable USB0 in peripheral mode
configs: j721e_evm: Add DFU related variables
configs: j721e_evm_r5_defconfig: Increase early malloc size
configs: j721e_evm_r5/a72_defconfig: Enable USB Gadget related configs
configs: j721e_evm_r5/a72_defconfig: Enable DFU related configs
.../arm/dts/k3-j721e-r5-common-proc-board.dts | 18 +++++++++++ arch/arm/mach-k3/include/mach/j721e_spl.h | 2 +- arch/arm/mach-k3/sysfw-loader.c | 30 +++++++++++++++++++ configs/j721e_evm_a72_defconfig | 6 ++++ configs/j721e_evm_r5_defconfig | 17 ++++++++++- include/configs/j721e_evm.h | 4 +++ 6 files changed, 75 insertions(+), 2 deletions(-)
Signature · 1 line
2.25.0
PATCH 1/7 arm: mach-k3: j721e: Rename BOOT_DEVICE_USB to BOOT_DEVICE_DFU
J721e does not support USB Host MSC boot, but only supports DFU boot. Since BOOT_DEVICE_USB is often used for host boot mode and BOOT_DEVICE_DFU is used for DFU boot, rename BOOT_DEVICE_USB macro to BOOT_DEVICE_DFU
--- arch/arm/mach-k3/include/mach/j721e_spl.h | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-)
arch/arm/mach-k3/include/mach/j721e_spl.h +1 -1
@@ -18,7 +18,7 @@/* With BootMode B = 1 */ #define BOOT_DEVICE_MMC2 0x10#define BOOT_DEVICE_MMC1 0x11 -#define BOOT_DEVICE_USB 0x12 +#define BOOT_DEVICE_DFU 0x12#define BOOT_DEVICE_UFS 0x13#define BOOT_DEVIE_GPMC 0x14#define BOOT_DEVICE_PCIE 0x15
Signature · 1 line
2.25.0
PATCH 2/7 arm: mach-k3: sysfw-loader: Add support to download SYSFW via DFU
In reply to Vignesh RaghavendraAdd support to download SYSFW into internal RAM via DFU in DFU boot mode. Prepare a DFU config entity entry dynamically using buffer address allocated for SYSFW and start DFU gadget to get SYSFW.
--- arch/arm/mach-k3/sysfw-loader.c | 30 ++++++++++++++++++++++++++++++ 1 file changed, 30 insertions(+)
arch/arm/mach-k3/sysfw-loader.c +30 -0
@@ -11,6 +11,10 @@#include <malloc.h> #include <remoteproc.h> #include <linux/soc/ti/ti_sci_protocol.h> +#include <g_dnl.h> +#include <usb.h> +#include <dfu.h> +#include <asm/arch/sys_proto.h> #include "common.h"
@@ -172,6 +176,27 @@ static void k3_sysfw_configure_using_fit(void *fit, ret); } +#if CONFIG_IS_ENABLED (DFU ) +static int k3_sysfw_dfu_download (void *addr) +{ +char dfu_str[50 ]; +int ret; + +sprintf (dfu_str,"sysfw.itb ram 0x%p 0x%x" , addr, +CONFIG_K3_SYSFW_IMAGE_SIZE_MAX ); + ret =dfu_config_entities (dfu_str,"ram" ,"0" ); +if (ret) { +dfu_free_entities (); + goto exit; + } + +run_usb_dnl_gadget (0 ,"usb_dnl_dfu" ); +exit: +dfu_free_entities (); +return ret; +} +#endif +void k3_sysfw_loader (void (*config_pm_done_callback)(void )) {struct spl_image_info spl_image = {0 };
@@ -235,6 +260,11 @@ void k3_sysfw_loader(void (*config_pm_done_callback)(void))#endif ret =spl_ymodem_load_image (&spl_image, &bootdev);break ; +#endif +#if CONFIG_IS_ENABLED (DFU ) +case BOOT_DEVICE_DFU : + ret =k3_sysfw_dfu_download (sysfw_load_address); +break ;#endif default : panic("Loading SYSFW image from device %u not supported!\n",
Signature · 1 line
2.25.0
PATCH 3/7 arm: dts: k3-j721e-common-proc-board: Enable USB0 in peripheral mode
In reply to Vignesh RaghavendraEnable USB0 in peripheral mode so that it be used for DFU
--- arch/arm/dts/k3-j721e-r5-common-proc-board.dts | 18 ++++++++++++++++++ 1 file changed, 18 insertions(+)
arch/arm/dts/k3-j721e-r5-common-proc-board.dts +18 -0
@@ -40,6 +40,13 @@ clock-frequency = <200000000>; u-boot,dm-spl; }; + + clk_19_2mhz: dummy_clock { + compatible = "fixed-clock"; + #clock-cells = <0>; + clock-frequency = <19200000>; + u-boot,dm-spl; + }; }; &cbass_mcu_wakeup {
@@ -207,4 +214,15 @@ u-boot,dm-spl; }; +&usbss0 { + /delete-property/ power-domains; + /delete-property/ assigned-clocks; + /delete-property/ assigned-clock-parents; + clocks = <&clk_19_2mhz>; + clock-names = "usb2_refclk"; + pinctrl-names = "default"; + pinctrl-0 = <&main_usbss0_pins_default>; + ti,vbus-divider; +}; + #include "k3-j721e-common-proc-board-u-boot.dtsi"
Signature · 1 line
2.25.0
PATCH 4/7 configs: j721e_evm: Add DFU related variables
In reply to Vignesh RaghavendraAdd configs to download varies stages of bootloader images to RAM during DFU boot.
--- include/configs/j721e_evm.h | 4 ++++ 1 file changed, 4 insertions(+)
include/configs/j721e_evm.h +4 -0
@@ -23,6 +23,8 @@#ifdef CONFIG_TARGET_J721E_A72_EVM #define CONFIG_SYS_INIT_SP_ADDR (CONFIG_SPL_TEXT_BASE + \ CONFIG_SYS_K3_NON_SECURE_MSRAM_SIZE) +/* Image load address in RAM for DFU boot*/ +#define CONFIG_SPL_LOAD_FIT_ADDRESS 0x81000000#else /* * Maximum size in memory allocated to the SPL BSS. Keep it as tight as
@@ -45,6 +47,8 @@/* Configure R5 SPL post-relocation malloc pool in DDR */ #define CONFIG_SYS_SPL_MALLOC_START 0x84000000#define CONFIG_SYS_SPL_MALLOC_SIZE SZ_16M +/* Image load address in RAM for DFU boot*/ +#define CONFIG_SPL_LOAD_FIT_ADDRESS 0x80080000#endif #ifdef CONFIG_SYS_K3_SPL_ATF
Signature · 1 line
2.25.0
PATCH 5/7 configs: j721e_evm_r5_defconfig: Increase early malloc size
In reply to Vignesh RaghavendraIncrease R5 SPL early malloc memory pool by ~7K to accommodate SPL USB DFU boot requirements
--- configs/j721e_evm_r5_defconfig | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-)
configs/j721e_evm_r5_defconfig +1 -1
@@ -3,7 +3,7 @@ CONFIG_ARCH_K3=y CONFIG_SPL_GPIO_SUPPORT=y CONFIG_SPL_LIBCOMMON_SUPPORT=y CONFIG_SPL_LIBGENERIC_SUPPORT=y -CONFIG_SYS_MALLOC_F_LEN=0x55000 +CONFIG_SYS_MALLOC_F_LEN=0x70000 CONFIG_SOC_K3_J721E=y CONFIG_TARGET_J721E_R5_EVM=y CONFIG_ENV_SIZE=0x20000
Signature · 1 line
2.25.0
PATCH 6/7 configs: j721e_evm_r5/a72_defconfig: Enable USB Gadget related configs
In reply to Vignesh RaghavendraEnable USB Gadget for R5 SPL, A72 SPL and A72 U-Boot to support DFU boot
--- configs/j721e_evm_a72_defconfig | 2 ++ configs/j721e_evm_r5_defconfig | 12 ++++++++++++ 2 files changed, 14 insertions(+)
configs/j721e_evm_a72_defconfig +2 -0
@@ -34,6 +34,7 @@ CONFIG_SPL_POWER_SUPPORT=y CONFIG_SPL_POWER_DOMAIN=y CONFIG_SPL_SPI_LOAD=y CONFIG_SYS_SPI_U_BOOT_OFFS=0x280000 +CONFIG_SPL_USB_GADGET=y CONFIG_SPL_YMODEM_SUPPORT=y CONFIG_CMD_ASKENV=y CONFIG_CMD_DFU=y
@@ -139,6 +140,7 @@ CONFIG_USB_XHCI_HCD=y CONFIG_USB_CDNS3=y CONFIG_USB_CDNS3_GADGET=y CONFIG_USB_CDNS3_HOST=y +CONFIG_SPL_USB_CDNS3_GADGET=y CONFIG_USB_GADGET=y CONFIG_USB_GADGET_MANUFACTURER="Texas Instruments" CONFIG_USB_GADGET_VENDOR_NUM=0x0451
configs/j721e_evm_r5_defconfig +12 -0
@@ -36,6 +36,7 @@ CONFIG_SPL_RAM_DEVICE=y CONFIG_SPL_REMOTEPROC=y CONFIG_SPL_SPI_LOAD=y CONFIG_SYS_SPI_U_BOOT_OFFS=0x80000 +CONFIG_SPL_USB_GADGET=y CONFIG_SPL_YMODEM_SUPPORT=y CONFIG_HUSH_PARSER=y # CONFIG_CMD_FLASH is not set
@@ -104,5 +105,16 @@ CONFIG_SYSRESET_TI_SCI=y CONFIG_TIMER=y CONFIG_SPL_TIMER=y CONFIG_OMAP_TIMER=y +CONFIG_USB=y +CONFIG_DM_USB=y +CONFIG_DM_USB_GADGET=y +CONFIG_SPL_DM_USB_GADGET=y +CONFIG_USB_CDNS3=y +CONFIG_USB_CDNS3_GADGET=y +CONFIG_SPL_USB_CDNS3_GADGET=y +CONFIG_USB_GADGET=y +CONFIG_USB_GADGET_MANUFACTURER="Texas Instruments" +CONFIG_USB_GADGET_VENDOR_NUM=0x0451 +CONFIG_USB_GADGET_PRODUCT_NUM=0x6163 CONFIG_FS_EXT4=y CONFIG_FS_FAT_MAX_CLUSTSIZE=16384
Signature · 1 line
2.25.0
PATCH 7/7 configs: j721e_evm_r5/a72_defconfig: Enable DFU related configs
In reply to Vignesh RaghavendraEnable DFU, Fastboot and USB mass storage gadget related configs
--- configs/j721e_evm_a72_defconfig | 4 ++++ configs/j721e_evm_r5_defconfig | 3 +++ 2 files changed, 7 insertions(+)
configs/j721e_evm_a72_defconfig +4 -0
@@ -32,9 +32,12 @@ CONFIG_SPL_DM_MAILBOX=y CONFIG_SPL_DM_RESET=y CONFIG_SPL_POWER_SUPPORT=y CONFIG_SPL_POWER_DOMAIN=y +CONFIG_SPL_RAM_SUPPORT=y +CONFIG_SPL_RAM_DEVICE=y CONFIG_SPL_SPI_LOAD=y CONFIG_SYS_SPI_U_BOOT_OFFS=0x280000 CONFIG_SPL_USB_GADGET=y +CONFIG_SPL_DFU=y CONFIG_SPL_YMODEM_SUPPORT=y CONFIG_CMD_ASKENV=y CONFIG_CMD_DFU=y
@@ -118,6 +121,7 @@ CONFIG_PINCTRL_SINGLE=y CONFIG_POWER_DOMAIN=y CONFIG_TI_SCI_POWER_DOMAIN=y CONFIG_RAM=y +CONFIG_SPL_RAM=y CONFIG_REMOTEPROC_TI_K3_DSP=y CONFIG_REMOTEPROC_TI_K3_R5F=y CONFIG_DM_RESET=y
configs/j721e_evm_r5_defconfig +3 -0
@@ -37,8 +37,10 @@ CONFIG_SPL_REMOTEPROC=y CONFIG_SPL_SPI_LOAD=y CONFIG_SYS_SPI_U_BOOT_OFFS=0x80000 CONFIG_SPL_USB_GADGET=y +CONFIG_SPL_DFU=y CONFIG_SPL_YMODEM_SUPPORT=y CONFIG_HUSH_PARSER=y +CONFIG_CMD_DFU=y # CONFIG_CMD_FLASH is not set CONFIG_CMD_GPT=y CONFIG_CMD_MMC=y
@@ -116,5 +118,6 @@ CONFIG_USB_GADGET=y CONFIG_USB_GADGET_MANUFACTURER="Texas Instruments" CONFIG_USB_GADGET_VENDOR_NUM=0x0451 CONFIG_USB_GADGET_PRODUCT_NUM=0x6163 +CONFIG_USB_GADGET_DOWNLOAD=y CONFIG_FS_EXT4=y CONFIG_FS_FAT_MAX_CLUSTSIZE=16384
Signature · 1 line
2.25.0
cover J721e: Add support for DFU boot mode
In reply to Vignesh RaghavendraQuoted 10 lines · Vignesh Raghavendra
This series adds support to boot via USB DFU mode.
Vignesh Raghavendra (7):
arm: mach-k3: j721e: RenameBOOT_DEVICE_USBtoBOOT_DEVICE_DFU
arm: mach-k3: sysfw-loader: Add support to download SYSFW via DFU
arm: dts: k3-j721e-common-proc-board: Enable USB0 in peripheral mode
configs:j721e_evm: Add DFU related variables
configs:j721e_evm_r5_defconfig: Increase early malloc size
configs: j721e_evm_r5/a72_defconfig: Enable USB Gadget related configs
configs: j721e_evm_r5/a72_defconfig: Enable DFU related configs
For all patches in the series:
--
Andreas Dannenberg
Texas Instruments Inc
Quoted 12 lines
.../arm/dts/k3-j721e-r5-common-proc-board.dts | 18 +++++++++++ arch/arm/mach-k3/include/mach/j721e_spl.h | 2 +- arch/arm/mach-k3/sysfw-loader.c | 30 +++++++++++++++++++ configs/j721e_evm_a72_defconfig | 6 ++++ configs/j721e_evm_r5_defconfig | 17 ++++++++++- include/configs/j721e_evm.h | 4 +++ 6 files changed, 75 insertions(+), 2 deletions(-)Signature · 1 line
2.25.0
cover J721e: Add support for DFU boot mode
In reply to Vignesh RaghavendraQuoted 1 line · Vignesh Raghavendra
This series adds support to boot via USB DFU mode.
Series pulled into u-boot-ti tree.
Thanks and regards,
Lokesh