Skip to contentSkip to conversation

dt-bindings: usb: add non-removable-ports hub property

PATCH RESEND In review Mans Rullgard 3 participants 13 messages Jan 24, 2020 – Jan 30, 2020

Subsystems (2)
lore
Share & tools
lore
#0 lore raw

PATCH RESEND 1/2 dt-bindings: usb: add non-removable-ports hub property

Add a non-removable-ports property that lists the hardwired downstream ports of a hub. Although hubs can provide this information, they are not always configured correctly. An alternate means of indicating this for built-in USB devices is thus useful.

---
 Documentation/devicetree/bindings/usb/usb-device.txt | 4 ++++
 1 file changed, 4 insertions(+)
Documentation/devicetree/bindings/usb/usb-device.txt +4 -0
index 036be172b1ae..92d863cc96b6 100644
@@ -66,6 +66,10 @@ Required properties for host-controller nodes with device nodes:
 - #size-cells: shall be 0
 
 
+Optional properties for hub and host-controller nodes:
+- non-removable-ports: list of hardwired downstream ports
+
+
 Example:
 
 &usb1 {	/* host controller */
Signature · 1 line
2.25.0
#1 lore raw

PATCH RESEND 2/2 usb: hub: use non-removable-ports DT property

Mark any ports listed in the non-removable-ports DT property as hardwired. This is useful for boards with built-in USB devices that cannot be (or have not been) marked as fixed in hardware.

---
 drivers/usb/core/hub.c | 16 ++++++++++++++++
 1 file changed, 16 insertions(+)
drivers/usb/core/hub.c +16 -0
index 4ac74b354801..97f8f15fb632 100644
@@ -1366,6 +1366,9 @@ static int hub_configure(struct usb_hub *hub,
 	unsigned unit_load;
 	unsigned full_load;
 	unsigned maxchild;
+	struct property *prop;
+	const __be32 *cur;
+	u32 val;
 
 	hub->buffer = kmalloc(sizeof(*hub->buffer), GFP_KERNEL);
 	if (!hub->buffer) {
@@ -1667,6 +1670,19 @@ static int hub_configure(struct usb_hub *hub,
 		}
 	}
 
+	of_property_for_each_u32(hub_dev->of_node, "non-removable-ports",
+				 prop, cur, val) {
+		if (val < 1 || val > hdev->maxchild) {
+			dev_warn(hub_dev,
+				 "bad port number %u in non-removable-ports\n",
+				 val);
+			continue;
+		}
+
+		hub->ports[val - 1]->connect_type =
+			USB_PORT_CONNECT_TYPE_HARD_WIRED;
+	}
+
 	usb_hub_adjust_deviceremovable(hdev, hub->descriptor);
 
 	hub_activate(hub, HUB_INIT);
Signature · 1 line
2.25.0
#2 lore raw

Re: [RESEND][PATCH 2/2] usb: hub: use non-removable-ports DT property

Quoted 30 lines · Mans Rullgard

Mark any ports listed in the non-removable-ports DT property as hardwired. This is useful for boards with built-in USB devices that cannot be (or have not been) marked as fixed in hardware.

---
 drivers/usb/core/hub.c | 16 ++++++++++++++++
 1 file changed, 16 insertions(+)
drivers/usb/core/hub.c +6 -0
index 4ac74b354801..97f8f15fb632 100644
@@ -1366,6 +1366,9 @@ static int hub_configure(struct usb_hub *hub,
 	unsigned unit_load;
 	unsigned full_load;
 	unsigned maxchild;
+	struct property *prop;
+	const __be32 *cur;
+	u32 val;
 
 	hub->buffer = kmalloc(sizeof(*hub->buffer), GFP_KERNEL);
 	if (!hub->buffer) {
@@ -1667,6 +1670,19 @@ static int hub_configure(struct usb_hub *hub,
 		}
 	}
 
+	of_property_for_each_u32(hub_dev->of_node, "non-removable-ports",
+				 prop, cur, val) {
+		if (val < 1 || val > hdev->maxchild) {

drivers/usb/core/hub.c static int hub_configure(struct usb_hub *hub, · line 1685

Quoted 10 lines
drivers/usb/core/hub.c +10 -0
+			dev_warn(hub_dev,
+				 "bad port number %u in non-removable-ports\n",
+				 val);
+			continue;
+		}
+
+		hub->ports[val - 1]->connect_type =
+			USB_PORT_CONNECT_TYPE_HARD_WIRED;
+	}
+

Is this doing the same thing that ACPI does? It doesn't seem like it, why not do this in usb_hub_adjust_deviceremovable()? Or wherever ACPI does this...

thanks,

greg k-h

maintainer
#3 lore raw
In reply to Mans Rullgard
Quoted 6 lines · Mans Rullgard

Add a non-removable-ports property that lists the hardwired downstream ports of a hub. Although hubs can provide this information, they are not always configured correctly. An alternate means of indicating this for built-in USB devices is thus useful.

I reviewed this already, but since you didn't add my reviewed-by, I'm looking at it again and having 2nd thoughts.

Quoted 9 lines
---
 Documentation/devicetree/bindings/usb/usb-device.txt | 4 ++++
 1 file changed, 4 insertions(+)
Documentation/devicetree/bindings/usb/usb-device.txt +0 -0
index 036be172b1ae..92d863cc96b6 100644

Documentation/devicetree/bindings/usb/usb-device.txt Required properties for host-controller nodes with device nodes: · line 70

Quoted 5 lines
Documentation/devicetree/bindings/usb/usb-device.txt +2 -0
@@ -66,6 +66,10 @@ Required properties for host-controller nodes with device nodes:
 - #size-cells: shall be 0
 
 
+Optional properties for hub and host-controller nodes:
+- non-removable-ports: list of hardwired downstream ports

If you have a hardwired device and need to know that, doesn't that imply there's some other stuff you need to describe beyond what a standard USB device has. Such as a power supply that's not Vbus from the hub.

At a minimum, I think this should be a per port property. Though really, I think this should just be implied by describing the device in DT. I'm not sure if there's a case for hotpluggable devices described in DT. Maybe with overlays.

Rob

#4 lore raw
Quoted 23 lines · Rob Herring
Quoted 6 lines · Mans Rullgard

Add a non-removable-ports property that lists the hardwired downstream ports of a hub. Although hubs can provide this information, they are not always configured correctly. An alternate means of indicating this for built-in USB devices is thus useful.

I reviewed this already, but since you didn't add my reviewed-by, I'm looking at it again and having 2nd thoughts.

Quoted 12 lines
---
 Documentation/devicetree/bindings/usb/usb-device.txt | 4 ++++
 1 file changed, 4 insertions(+)
Documentation/devicetree/bindings/usb/usb-device.txt +0 -0
index 036be172b1ae..92d863cc96b6 100644
@@ -66,6 +66,10 @@ Required properties for host-controller nodes with device nodes:
 - #size-cells: shall be 0
 
 
Quoted 6 lines

Documentation/devicetree/bindings/usb/usb-device.txt Required properties for host-controller nodes with device nodes: · line 70

Quoted 2 lines
Documentation/devicetree/bindings/usb/usb-device.txt +2 -0
+Optional properties for hub and host-controller nodes:
+- non-removable-ports: list of hardwired downstream ports

If you have a hardwired device and need to know that, doesn't that imply there's some other stuff you need to describe beyond what a standard USB device has. Such as a power supply that's not Vbus from the hub.

I suppose there could be, but there isn't in my actual situation.

Quoted 1 line

At a minimum, I think this should be a per port property.

That's what I suggested first. Greg told me to do it like this instead.

Quoted 3 lines

Though really, I think this should just be implied by describing the device in DT. I'm not sure if there's a case for hotpluggable devices described in DT. Maybe with overlays.

That's also an option. Greg, what do you think?

Signature · 1 line
Måns Rullgård
#5 lore raw
Quoted 32 lines · Måns Rullgård
Quoted 23 lines · Rob Herring
Quoted 6 lines · Mans Rullgard

Add a non-removable-ports property that lists the hardwired downstream ports of a hub. Although hubs can provide this information, they are not always configured correctly. An alternate means of indicating this for built-in USB devices is thus useful.

I reviewed this already, but since you didn't add my reviewed-by, I'm looking at it again and having 2nd thoughts.

Quoted 12 lines
---
 Documentation/devicetree/bindings/usb/usb-device.txt | 4 ++++
 1 file changed, 4 insertions(+)
Documentation/devicetree/bindings/usb/usb-device.txt +0 -0
index 036be172b1ae..92d863cc96b6 100644
@@ -66,6 +66,10 @@ Required properties for host-controller nodes with device nodes:
 - #size-cells: shall be 0
 
 
Quoted 6 lines

Documentation/devicetree/bindings/usb/usb-device.txt Required properties for host-controller nodes with device nodes: · line 70

Quoted 2 lines
Documentation/devicetree/bindings/usb/usb-device.txt +2 -0
+Optional properties for hub and host-controller nodes:
+- non-removable-ports: list of hardwired downstream ports

If you have a hardwired device and need to know that, doesn't that imply there's some other stuff you need to describe beyond what a standard USB device has. Such as a power supply that's not Vbus from the hub.

Quoted 5 lines

I suppose there could be, but there isn't in my actual situation.

Quoted 1 line

At a minimum, I think this should be a per port property.

That's what I suggested first. Greg told me to do it like this instead.

I said that? I do not remember discussing this at all, when did that happen?

Quoted 5 lines
Quoted 3 lines

Though really, I think this should just be implied by describing the device in DT. I'm not sure if there's a case for hotpluggable devices described in DT. Maybe with overlays.

That's also an option. Greg, what do you think?

I have no idea, sorry, I'm totally lost here...

greg k-h

Quoted 3 lines
Signature · 2 lines
-- 
Måns Rullgård
#6 lore raw
Quoted 33 lines · Greg Kroah-Hartman
Quoted 32 lines · Måns Rullgård
Quoted 29 lines · Rob Herring
Quoted 6 lines · Mans Rullgard

Add a non-removable-ports property that lists the hardwired downstream ports of a hub. Although hubs can provide this information, they are not always configured correctly. An alternate means of indicating this for built-in USB devices is thus useful.

I reviewed this already, but since you didn't add my reviewed-by, I'm looking at it again and having 2nd thoughts.

Quoted 9 lines
---
 Documentation/devicetree/bindings/usb/usb-device.txt | 4 ++++
 1 file changed, 4 insertions(+)
Documentation/devicetree/bindings/usb/usb-device.txt +0 -0
index 036be172b1ae..92d863cc96b6 100644

Documentation/devicetree/bindings/usb/usb-device.txt Required properties for host-controller nodes with device nodes: · line 70

Quoted 5 lines
Documentation/devicetree/bindings/usb/usb-device.txt +2 -0
@@ -66,6 +66,10 @@ Required properties for host-controller nodes with device nodes:
 - #size-cells: shall be 0
 
 
+Optional properties for hub and host-controller nodes:
+- non-removable-ports: list of hardwired downstream ports

If you have a hardwired device and need to know that, doesn't that imply there's some other stuff you need to describe beyond what a standard USB device has. Such as a power supply that's not Vbus from the hub.

Quoted 8 lines
Quoted 5 lines

I suppose there could be, but there isn't in my actual situation.

Quoted 1 line

At a minimum, I think this should be a per port property.

That's what I suggested first. Greg told me to do it like this instead.

I said that? I do not remember discussing this at all, when did that happen?

https://lore.kernel.org/lkml/[email protected]/

Quoted 7 lines
Quoted 5 lines
Quoted 3 lines

Though really, I think this should just be implied by describing the device in DT. I'm not sure if there's a case for hotpluggable devices described in DT. Maybe with overlays.

That's also an option. Greg, what do you think?

I have no idea, sorry, I'm totally lost here...

Background: I need to differentiate between on-board and external USB devices on a few boards. Although hubs can indicate the removable status of each port, the configuration options are often limited and may not be capable of describing the actual wiring. Also, if a device is hard-wired directly to a host port, there is no way of indicating this.

While I could match the full device path using per-board lists, I'd prefer a generic solution. To this end, it is necessary to add the ability for DT to supply this information. Three variants have been discussed:

1. Add a "non-removable" property to the USB device node similar to how it's done for MMC.

2. Add a "non-removable-ports" property to the hub node. Apparently ACPI can supply the information in this manner.

3. Make any USB device with a DT node implicitly non-removable.

Either one will work for me.

Signature · 1 line
Måns Rullgård
#7 lore raw
Quoted 37 lines · Måns Rullgård
Quoted 35 lines · Greg Kroah-Hartman
Quoted 34 lines · Måns Rullgård
Quoted 23 lines · Rob Herring
Quoted 6 lines · Mans Rullgard

Add a non-removable-ports property that lists the hardwired downstream ports of a hub. Although hubs can provide this information, they are not always configured correctly. An alternate means of indicating this for built-in USB devices is thus useful.

I reviewed this already, but since you didn't add my reviewed-by, I'm looking at it again and having 2nd thoughts.

Quoted 12 lines
---
 Documentation/devicetree/bindings/usb/usb-device.txt | 4 ++++
 1 file changed, 4 insertions(+)
Documentation/devicetree/bindings/usb/usb-device.txt +0 -0
index 036be172b1ae..92d863cc96b6 100644
@@ -66,6 +66,10 @@ Required properties for host-controller nodes with device nodes:
 - #size-cells: shall be 0
 
 
Quoted 6 lines

Documentation/devicetree/bindings/usb/usb-device.txt Required properties for host-controller nodes with device nodes: · line 70

Quoted 2 lines
Documentation/devicetree/bindings/usb/usb-device.txt +2 -0
+Optional properties for hub and host-controller nodes:
+- non-removable-ports: list of hardwired downstream ports

If you have a hardwired device and need to know that, doesn't that imply there's some other stuff you need to describe beyond what a standard USB device has. Such as a power supply that's not Vbus from the hub.

I suppose there could be, but there isn't in my actual situation.

Quoted 8 lines
Quoted 6 lines
Quoted 3 lines
Quoted 1 line

At a minimum, I think this should be a per port property.

That's what I suggested first. Greg told me to do it like this instead.

I said that? I do not remember discussing this at all, when did that happen?

https://lore.kernel.org/lkml/[email protected]/

Almost a full year ago! Hah, I can't remember what I wrote last week.

#8 lore raw
Quoted 40 lines · Greg Kroah-Hartman
Quoted 39 lines · Måns Rullgård
Quoted 37 lines · Greg Kroah-Hartman
Quoted 36 lines · Måns Rullgård
Quoted 23 lines · Rob Herring
Quoted 6 lines · Mans Rullgard

Add a non-removable-ports property that lists the hardwired downstream ports of a hub. Although hubs can provide this information, they are not always configured correctly. An alternate means of indicating this for built-in USB devices is thus useful.

I reviewed this already, but since you didn't add my reviewed-by, I'm looking at it again and having 2nd thoughts.

Quoted 12 lines
---
 Documentation/devicetree/bindings/usb/usb-device.txt | 4 ++++
 1 file changed, 4 insertions(+)
Documentation/devicetree/bindings/usb/usb-device.txt +0 -0
index 036be172b1ae..92d863cc96b6 100644
@@ -66,6 +66,10 @@ Required properties for host-controller nodes with device nodes:
 - #size-cells: shall be 0
 
 
Quoted 6 lines

Documentation/devicetree/bindings/usb/usb-device.txt Required properties for host-controller nodes with device nodes: · line 70

Quoted 2 lines
Documentation/devicetree/bindings/usb/usb-device.txt +2 -0
+Optional properties for hub and host-controller nodes:
+- non-removable-ports: list of hardwired downstream ports

If you have a hardwired device and need to know that, doesn't that imply there's some other stuff you need to describe beyond what a standard USB device has. Such as a power supply that's not Vbus from the hub.

I suppose there could be, but there isn't in my actual situation.

Quoted 1 line

At a minimum, I think this should be a per port property.

Quoted 8 lines
Quoted 6 lines
Quoted 4 lines
Quoted 1 line

That's what I suggested first. Greg told me to do it like this instead.

I said that? I do not remember discussing this at all, when did that happen?

https://lore.kernel.org/lkml/[email protected]/

Almost a full year ago! Hah, I can't remember what I wrote last week.

Ah, ok, all I said was "do what ACPI does here", as that's a model of what has already been agreed apon by a whole huge number of people and standardized. No need for DT to come up with something totally different instead, making a mess of things :)

If this is doing what ACPI does, fine, if not, it should. It was here first.

thanks,

greg k-h

maintainer
#9 lore raw

n Tue, Jan 28, 2020 at 10:52 AM Greg Kroah-Hartman

Quoted 51 lines · <[email protected]> wrote:
Quoted 40 lines · Greg Kroah-Hartman
Quoted 39 lines · Måns Rullgård
Quoted 37 lines · Greg Kroah-Hartman
Quoted 36 lines · Måns Rullgård
Quoted 23 lines · Rob Herring
Quoted 6 lines · Mans Rullgard

Add a non-removable-ports property that lists the hardwired downstream ports of a hub. Although hubs can provide this information, they are not always configured correctly. An alternate means of indicating this for built-in USB devices is thus useful.

I reviewed this already, but since you didn't add my reviewed-by, I'm looking at it again and having 2nd thoughts.

Quoted 12 lines
---
 Documentation/devicetree/bindings/usb/usb-device.txt | 4 ++++
 1 file changed, 4 insertions(+)
Documentation/devicetree/bindings/usb/usb-device.txt +0 -0
index 036be172b1ae..92d863cc96b6 100644
@@ -66,6 +66,10 @@ Required properties for host-controller nodes with device nodes:
 - #size-cells: shall be 0
 
 
Quoted 6 lines

Documentation/devicetree/bindings/usb/usb-device.txt Required properties for host-controller nodes with device nodes: · line 70

Quoted 2 lines
Documentation/devicetree/bindings/usb/usb-device.txt +2 -0
+Optional properties for hub and host-controller nodes:
+- non-removable-ports: list of hardwired downstream ports

If you have a hardwired device and need to know that, doesn't that imply there's some other stuff you need to describe beyond what a standard USB device has. Such as a power supply that's not Vbus from the hub.

I suppose there could be, but there isn't in my actual situation.

Quoted 1 line

At a minimum, I think this should be a per port property.

Quoted 8 lines
Quoted 6 lines
Quoted 4 lines
Quoted 1 line

That's what I suggested first. Greg told me to do it like this instead.

I said that? I do not remember discussing this at all, when did that happen?

https://lore.kernel.org/lkml/[email protected]/

Almost a full year ago! Hah, I can't remember what I wrote last week.

Quoted 7 lines

Ah, ok, all I said was "do what ACPI does here", as that's a model of what has already been agreed apon by a whole huge number of people and standardized. No need for DT to come up with something totally different instead, making a mess of things :)

If this is doing what ACPI does, fine, if not, it should. It was here first.

That's not always possible as ACPI and DT work in different ways. The DT (Open Firmware) USB binding originated in 1998[1]. While ancient, that is what defines the node structure of USB hubs, ports, and devices that we use today.

However, after a quick read of ACPI sec 9.14, I'd say what I suggested is more aligned to ACPI than what's proposed here. Ports are child nodes ("Device" in ACPI terms) and the properties to determine all this are properties of the port node(s). Aligning beyond that isn't really possible. ACPI has a standard thing (not sure what the proper term is) called '_PLD' for describing device location which includes 'user visible' among several other things. There is no such concept in DT to align with. What we have is the 'non-removable' property and IMO that's what we should use here.

Rob

[1] https://www.devicetree.org/open-firmware/bindings/usb/usb-1_0.ps

#10 lore raw
Quoted 66 lines · Rob Herring

n Tue, Jan 28, 2020 at 10:52 AM Greg Kroah-Hartman

Quoted 51 lines · <[email protected]> wrote:
Quoted 40 lines · Greg Kroah-Hartman
Quoted 39 lines · Måns Rullgård
Quoted 37 lines · Greg Kroah-Hartman
Quoted 36 lines · Måns Rullgård
Quoted 23 lines · Rob Herring
Quoted 6 lines · Mans Rullgard

Add a non-removable-ports property that lists the hardwired downstream ports of a hub. Although hubs can provide this information, they are not always configured correctly. An alternate means of indicating this for built-in USB devices is thus useful.

I reviewed this already, but since you didn't add my reviewed-by, I'm looking at it again and having 2nd thoughts.

Quoted 12 lines
---
 Documentation/devicetree/bindings/usb/usb-device.txt | 4 ++++
 1 file changed, 4 insertions(+)
Documentation/devicetree/bindings/usb/usb-device.txt +0 -0
index 036be172b1ae..92d863cc96b6 100644
@@ -66,6 +66,10 @@ Required properties for host-controller nodes with device nodes:
 - #size-cells: shall be 0
 
 
Quoted 6 lines

Documentation/devicetree/bindings/usb/usb-device.txt Required properties for host-controller nodes with device nodes: · line 70

Quoted 2 lines
Documentation/devicetree/bindings/usb/usb-device.txt +2 -0
+Optional properties for hub and host-controller nodes:
+- non-removable-ports: list of hardwired downstream ports

If you have a hardwired device and need to know that, doesn't that imply there's some other stuff you need to describe beyond what a standard USB device has. Such as a power supply that's not Vbus from the hub.

I suppose there could be, but there isn't in my actual situation.

Quoted 1 line

At a minimum, I think this should be a per port property.

Quoted 8 lines
Quoted 6 lines
Quoted 4 lines
Quoted 1 line

That's what I suggested first. Greg told me to do it like this instead.

I said that? I do not remember discussing this at all, when did that happen?

https://lore.kernel.org/lkml/[email protected]/

Almost a full year ago! Hah, I can't remember what I wrote last week.

Quoted 7 lines

Ah, ok, all I said was "do what ACPI does here", as that's a model of what has already been agreed apon by a whole huge number of people and standardized. No need for DT to come up with something totally different instead, making a mess of things :)

If this is doing what ACPI does, fine, if not, it should. It was here first.

That's not always possible as ACPI and DT work in different ways. The DT (Open Firmware) USB binding originated in 1998[1]. While ancient, that is what defines the node structure of USB hubs, ports, and devices that we use today.

Quoted 9 lines

However, after a quick read of ACPI sec 9.14, I'd say what I suggested is more aligned to ACPI than what's proposed here. Ports are child nodes ("Device" in ACPI terms) and the properties to determine all this are properties of the port node(s). Aligning beyond that isn't really possible. ACPI has a standard thing (not sure what the proper term is) called '_PLD' for describing device location which includes 'user visible' among several other things. There is no such concept in DT to align with. What we have is the 'non-removable' property and IMO that's what we should use here.

Can you guys please agree on something or other. I'm happy to do it whichever way you decide, but I'd rather not waste my time making patches that will just get rejected.

Signature · 1 line
Måns Rullgård
maintainer
#11 lore raw
In reply to Greg Kroah-Hartman
Quoted 41 lines · Greg Kroah-Hartman
Quoted 39 lines · Måns Rullgård
Quoted 37 lines · Greg Kroah-Hartman
Quoted 36 lines · Måns Rullgård
Quoted 23 lines · Rob Herring
Quoted 6 lines · Mans Rullgard

Add a non-removable-ports property that lists the hardwired downstream ports of a hub. Although hubs can provide this information, they are not always configured correctly. An alternate means of indicating this for built-in USB devices is thus useful.

I reviewed this already, but since you didn't add my reviewed-by, I'm looking at it again and having 2nd thoughts.

Quoted 12 lines
---
 Documentation/devicetree/bindings/usb/usb-device.txt | 4 ++++
 1 file changed, 4 insertions(+)
Documentation/devicetree/bindings/usb/usb-device.txt +0 -0
index 036be172b1ae..92d863cc96b6 100644
@@ -66,6 +66,10 @@ Required properties for host-controller nodes with device nodes:
 - #size-cells: shall be 0
 
 
Quoted 6 lines

Documentation/devicetree/bindings/usb/usb-device.txt Required properties for host-controller nodes with device nodes: · line 70

Quoted 2 lines
Documentation/devicetree/bindings/usb/usb-device.txt +2 -0
+Optional properties for hub and host-controller nodes:
+- non-removable-ports: list of hardwired downstream ports

If you have a hardwired device and need to know that, doesn't that imply there's some other stuff you need to describe beyond what a standard USB device has. Such as a power supply that's not Vbus from the hub.

I suppose there could be, but there isn't in my actual situation.

Quoted 1 line

At a minimum, I think this should be a per port property.

Quoted 8 lines
Quoted 6 lines
Quoted 4 lines
Quoted 1 line

That's what I suggested first. Greg told me to do it like this instead.

I said that? I do not remember discussing this at all, when did that happen?

https://lore.kernel.org/lkml/[email protected]/

Almost a full year ago! Hah, I can't remember what I wrote last week.

I was typing up the same thing... :)

#12 lore raw
In reply to Mans Rullgard
Quoted 9 lines · Mans Rullgard

Add a non-removable-ports property that lists the hardwired downstream ports of a hub. Although hubs can provide this information, they are not always configured correctly. An alternate means of indicating this for built-in USB devices is thus useful.

---
 Documentation/devicetree/bindings/usb/usb-device.txt | 4 ++++
 1 file changed, 4 insertions(+)

Why is this a RESEND? What changed from v1?

thanks,

greg k-h