USB HID random timeout failures fixed by trying 20 times
Subsystems (2)
PATCH 1/1 USB HID random timeout failures fixed by trying 20 times
send, 20ms apart, control messages, if error is timeout.
---drivers/usb/core/message.c | 30 +++++++++++++++++++++++++-----
1 file changed, 25 insertions(+), 5 deletions(-)
drivers/usb/core/message.c +0 -0
@@ -20,6 +20,7 @@
#include <linux/usb/hcd.h> /* for usbcore internals */ #include <linux/usb/of.h>
#include <asm/byteorder.h>
+#include <linux/errno.h>
#include "usb.h"
@@ -137,7 +138,10 @@ int usb_control_msg(struct usb_device *dev, unsigned int pipe, __u8 request, __u16 size, int timeout)
{
struct usb_ctrlrequest *dr;
- int ret;
+ int ret = -ETIMEDOUT;
+
+ /* retry_cnt * 10ms, max retry time set to 400ms */
+ int retry_cnt = 20;
dr = kmalloc(sizeof(struct usb_ctrlrequest), GFP_NOIO);
if (!dr)
@@ -149,11 +153,27 @@ int usb_control_msg(struct usb_device *dev, unsigned int pipe, __u8 request, dr->wIndex = cpu_to_le16(index);dr->wLength = cpu_to_le16(size);
- ret = usb_internal_control_msg(dev, pipe, dr, data, size, timeout);
+ do {
+ ret = usb_internal_control_msg(dev,
+ pipe,
+ dr,
+ data,
+ size,
+ timeout);
+
+ /*
+ * Linger a bit, prior to the next control message
+ * or if return value is timeout, but do try few
+ * times (max 200ms) before quitting.
+ */
+ if (dev->quirks & USB_QUIRK_DELAY_CTRL_MSG)
+ msleep(200);
+ else if (ret = -ETIMEDOUT)
+ msleep(20);
+
+ /* Loop while timeout, max retry_cnt times. */
+ } while ((retry_cnt-- > 0) && (ret = -ETIMEDOUT));
- /* Linger a bit, prior to the next control message. */
- if (dev->quirks & USB_QUIRK_DELAY_CTRL_MSG)
- msleep(200);
kfree(dr);
Signature · 1 line
2.25.0
Hi Lauri,
There are a bunch of issues with this patch.
1) There is no way we're going to add a retry loop to usb_control_msg(). We might add it to a driver, but probably we would suspect that the hardware is bad. Maybe the cable is faulty? Or I could be wrong on that...
2) You would need to send this to a different list. Use ./scripts/get_maintainer.pl to find out who. The [email protected] is the main USB list.
3) The patch doesn't apply. Read the first paragraph of Documentation/process/email-clients.rst
4) The subject needs to be formatted slightly differently. [PATCH] USB: HID: Fix timeout by adding retry loop
5) The commit message should be more clear what was affected. Don't start the commit message in the middle of a sentence.
regards,
dan carpenter
Re: [PATCH] USB: HID: Fix timeout by adding retry loop
Hi,
I'm quite newbie publicly patching stuff, but at anyway:
Quoted 8 lines · Dan Carpenter
Hi Lauri,
There are a bunch of issues with this patch.
1) There is no way we're going to add a retry loop to
usb_control_msg(). We might add it to a driver, but probably we would suspect that the hardware is bad. Maybe the cable is faulty? Or I could be wrong on that...
For example there is lot of USB HID related oddities reported
by multiple users, that have said that after (kernel) update
of their system USB devices stopped working or work randomly.
I have problem with my mouse, and the problem went away
with my patch. I think that the change to driver by driver is
just code duplication, and with my patch the 'good' HW still
is not going to sleep even that 20ms, the time that I tought
to be good. Max retry time is 400ms.
Quoted 4 lines
2) You would need to send this to a different list. Use
./scripts/get_maintainer.plto find out who. The [email protected] is the main USB list.
I'm just beginner, but the MAINTAINERS list mentiones
linus-usb mailing list.
Quoted 2 lines
3) The patch doesn't apply. Read the first paragraph of
Documentation/process/email-clients.rst
Ok, will do just that.
Quoted 2 lines
4) The subject needs to be formatted slightly differently. [PATCH] USB: HID: Fix timeout by adding retry loop
Ok, modified subject as requested.
Quoted 2 lines
5) The commit message should be more clear what was affected. Don't start the commit message in the middle of a sentence.
I try to elaborate bit more.
Quoted 4 lines
regards,
dan carpenter
Thank you for commit review. I start to fix patch as you suggested.
Br,
Lauri J.
Re: [PATCH] USB: HID: Fix timeout by adding retry loop
Quoted 23 lines · Lauri Jakku
Hi,
I'm quite newbie publicly patching stuff, but at anyway:
Quoted 8 lines · Dan Carpenter
Hi Lauri,
There are a bunch of issues with this patch.
1) There is no way we're going to add a retry loop to
usb_control_msg(). We might add it to a driver, but probably we would suspect that the hardware is bad. Maybe the cable is faulty? Or I could be wrong on that...For example there is lot of USB HID related oddities reported
by multiple users, that have said that after (kernel) update
of their system USB devices stopped working or work randomly.
I have problem with my mouse, and the problem went away
Quoted 8 lines
with my patch. I think that the change to driver by driver is
just code duplication, and with my patch the 'good' HW still
is not going to sleep even that 20ms, the time that I tought
to be good. Max retry time is 400ms.
That doesn't sound totally unreasonable. Go ahead and try sending the patch. Maybe they apply it or maybe they don't but either way there is no harm in sending a patch.
regards,
dan carpenter
USB Hid Timeout and r8169 module to trust HW if present.
Hi,
I got this timeout patch and patch for r8168 to work, both are situations that i've had, and fixes work for me ok.
Where do I send them ?
--Lauri
Quoted 29 lines · Dan Carpenter
Quoted 28 lines · Lauri Jakku
Hi,
I'm quite newbie publicly patching stuff, but at anyway:
Quoted 8 lines · Dan Carpenter
Hi Lauri,
There are a bunch of issues with this patch.
1) There is no way we're going to add a retry loop to
usb_control_msg(). We might add it to a driver, but probably we would suspect that the hardware is bad. Maybe the cable is faulty? Or I could be wrong on that...For example there is lot of USB HID related oddities reported
by multiple users, that have said that after (kernel) update
of their system USB devices stopped working or work randomly.
I have problem with my mouse, and the problem went away
with my patch. I think that the change to driver by driver is
just code duplication, and with my patch the 'good' HW still
is not going to sleep even that 20ms, the time that I tought
Quoted 9 lines
Quoted 2 lines
to be good. Max retry time is 400ms.
That doesn't sound totally unreasonable. Go ahead and try sending the patch. Maybe they apply it or maybe they don't but either way there is no harm in sending a patch.
regards,
dan carpenter
From 8e9898889c035e6301c7e92b1a63717d441eded6 Mon Sep 17 00:00:00 2001
From: Lauri Jakku <[email protected]>
Date: Mon, 9 Aug 2021 21:44:53 +0300
Subject: [PATCH 1/2] net:realtek:r8169, driver load fix
net:realtek:r8169
Problem:
The driver seems not to work at first run, not even when proper HW is detected by it at the first probe.
Solution:
the driver will trust the HW that reports valid ID and then make re-loading of the module as it would being reloaded manually
--- .../drivers/net/ethernet/realtek/r8169_main.c | 35 ++++++++++++++--- linux-5.14-rc4/drivers/net/phy/phy_device.c | 38 +++++++++++++++++++ 2 files changed, 67 insertions(+), 6 deletions(-)
linux-5.14-rc4/drivers/net/ethernet/realtek/r8169_main.c +29 -6
@@ -634,6 +634,8 @@ struct rtl8169_private {struct rtl_fw *rtl_fw;u32 ocp_base; + +int retry_probeing; };typedef void (*rtl_generic_fct )(struct rtl8169_private *tp);
@@ -5097,13 +5099,16 @@ static int r8169_mdio_register(struct rtl8169_private *tp) tp->phydev =mdiobus_get_phy (new_bus,0 );if (!tp->phydev) {return -ENODEV ; - }else if (!tp->phydev->drv) { -/* Most chip versions fail with the genphy driver. -* Therefore ensure that the dedicated PHY driver is loaded. + }else if (tp->phydev->phy_id !=RTL_GIGA_MAC_NONE ) { +/* Most chip versions fail with the genphy driver, BUT do rerport valid IW +* ID. Re-starting the module seem to fix the issue of non-functional driver. */ -dev_err (&pdev->dev,"no dedicated PHY driver found for PHY ID 0x%08x, maybe realtek.ko needs to be added to initramfs?\n" , +dev_err (&pdev->dev, +"no dedicated driver, but HW found: PHY PHY ID 0x%08x\n" , tp->phydev->phy_id); -return -EUNATCH ; + +dev_err (&pdev->dev,"trying re-probe few times..\n" ); + } tp->phydev->mac_managed_pm =1 ;
@@ -5250,6 +5255,7 @@ static int rtl_init_one(struct pci_dev *pdev, const struct pci_device_id *ent)enum mac_version chipset;struct net_device *dev;u16 xid; +int savederr =0 ; dev =devm_alloc_etherdev (&pdev->dev,sizeof (*tp));if (!dev)
@@ -5261,6 +5267,7 @@ static int rtl_init_one(struct pci_dev *pdev, const struct pci_device_id *ent) tp->dev = dev; tp->pci_dev = pdev; tp->supports_gmii = ent->driver_data ==RTL_CFG_NO_GBIT ?0 :1 ; + tp->retry_probeing =0 ; tp->eee_adv =-1 ; tp->ocp_base =OCP_STD_PHY_BASE ;
@@ -5410,7 +5417,15 @@ static int rtl_init_one(struct pci_dev *pdev, const struct pci_device_id *ent)pci_set_drvdata (pdev, tp); - rc =r8169_mdio_register (tp); + savederr =r8169_mdio_register (tp); + +if ( + (tp->retry_probeing >0 ) && + (savederr == -EAGAIN ) + ) { +netdev_info (dev," retry of probe requested.............." ); + } +if (rc)return rc;
@@ -5435,6 +5450,14 @@ static int rtl_init_one(struct pci_dev *pdev, const struct pci_device_id *ent)if (pci_dev_run_wake (pdev))pm_runtime_put_sync (&pdev->dev); +if ( + (tp->retry_probeing >0 ) && + (savederr == -EAGAIN ) + ) { +netdev_info (dev," retry of probe requested.............." ); +return savederr; + } +return 0 ; }
linux-5.14-rc4/drivers/net/phy/phy_device.c +38 -0
@@ -2980,6 +2980,9 @@ struct fwnode_handle *fwnode_get_phy_node(struct fwnode_handle *fwnode) }EXPORT_SYMBOL_GPL (fwnode_get_phy_node); + +static int phy_remove (struct device *dev); +/** * phy_probe - probe and init a PHY device * @dev: device to probe and init
@@ -2988,13 +2991,22 @@ EXPORT_SYMBOL_GPL(fwnode_get_phy_node);* set the state to READY (the driver's init function should * set it to STARTING if needed). */ +#define REDO_PROBE_TIMES 5static int phy_probe (struct device *dev) {struct phy_device *phydev =to_phy_device (dev);struct device_driver *drv = phydev->mdio.dev.driver;struct phy_driver *phydrv =to_phy_driver (drv); +int again =0 ; +int savederr =0 ; +again_retry:int err =0 ; +if (again >0 ) { +pr_err ("%s: Re-probe %d of driver.....\n" , + phydrv->name, again); + } + phydev->drv = phydrv;/* Disable the interrupt if the PHY doesn't support it
@@ -3013,6 +3025,17 @@ static int phy_probe(struct device *dev)if (phydev->drv->probe) { err = phydev->drv->probe (phydev); + +/* If again requested. */ +if (err == -EAGAIN ) { + again++; + savederr = err; + err =0 ; + +pr_info ("%s: EAGAIN: %d ...\n" , + phydrv->name, again); + } +if (err) goto out; }
@@ -3081,6 +3104,20 @@ static int phy_probe(struct device *dev)mutex_unlock (&phydev->lock); +if ((savederr == -EAGAIN ) && + ((again >0 ) && (again <REDO_PROBE_TIMES )) + ) { +pr_err ("%s: Retry removal driver..\n" , + phydrv->name); + +phy_remove (dev); + +pr_err ("%s: Re-probe driver..\n" , + phydrv->name); + savederr =0 ; + goto again_retry; + } +return err; }
@@ -3108,6 +3145,7 @@ static int phy_remove(struct device *dev)return 0 ; } +static void phy_shutdown (struct device *dev) {struct phy_device *phydev =to_phy_device (dev);
Signature · 1 line
2.17.1
From b9838664ed2ac62eb2a957f477bf57d79f09da73 Mon Sep 17 00:00:00 2001
From: Lauri Jakku <[email protected]>
Date: Mon, 9 Aug 2021 21:44:53 +0300
Subject: [PATCH 2/2] USB core tinkering:
USB:core:message:
Problem:
Timeout happening in USB transfer some times.
Solution:
Linger a bit, prior to the next control message or if return value is timeout, but do try few times before quitting.
--- linux-5.14-rc4/drivers/usb/core/message.c | 28 +++++++++++++++++++---- 1 file changed, 23 insertions(+), 5 deletions(-)
linux-5.14-rc4/drivers/usb/core/message.c +23 -5
@@ -21,6 +21,7 @@#include <linux/usb/hcd.h> /* for usbcore internals */ #include <linux/usb/of.h> #include <asm/byteorder.h> +#include <uapi/asm-generic/errno.h> #include "usb.h"
@@ -138,7 +139,12 @@ int usb_control_msg(struct usb_device *dev, unsigned int pipe, __u8 request, __u16 size, int timeout) {struct usb_ctrlrequest *dr; -int ret; +int ret = -ETIMEDOUT ; +int retry_cnt =5 ; + +/* By default: while done at least one time */ +int retryStill =1 ; +int isTimeout =1 ; dr =kmalloc (sizeof (struct usb_ctrlrequest ),GFP_NOIO );if (!dr)
@@ -150,11 +156,23 @@ int usb_control_msg(struct usb_device *dev, unsigned int pipe, __u8 request, dr->wIndex =cpu_to_le16 (index); dr->wLength =cpu_to_le16 (size); - ret =usb_internal_control_msg (dev, pipe, dr, data, size, timeout); -/* Linger a bit, prior to the next control message. */ -if (dev->quirks &USB_QUIRK_DELAY_CTRL_MSG ) -msleep (200 ); +while (retryStill && isTimeout) { + ret =usb_internal_control_msg (dev, pipe, dr, data, size, timeout); + +/* +* Linger a bit, prior to the next control message or if return +* value is timeout, but do try few times before quitting. +*/ + + retryStill = (retry_cnt >0 ); + isTimeout = (ret == -ETIMEDOUT ); + +if ((dev->quirks &USB_QUIRK_DELAY_CTRL_MSG ) || isTimeout) +msleep (200 ); + + retry_cnt-- + }kfree (dr);
Signature · 1 line
2.17.1
Re: USB Hid Timeout and r8169 module to trust HW if present.
Hi, Now i got it working without user meddeling at all:
From: Lauri Jakku <[email protected]>
Date: Mon, 9 Aug 2021 21:44:53 +0300
Subject: [PATCH] net:realtek:r8169 driver load fix
net:realtek:r8169
Problem:
The driver seems not to work at first run for some HW's, not even when proper hardware is detected by it at the first probe.
Solution:
the driver will trust the hardware that reports valid ID and then make re-loading of the module as it would being reloaded manually.
---
.../drivers/net/ethernet/realtek/r8169_main.c | 35 ++++++++++++++--- linux-5.14-rc4/drivers/net/phy/phy_device.c | 38 +++++++++++++++++++
2 files changed, 67 insertions(+), 6 deletions(-)
linux-5.14-rc4/drivers/net/ethernet/realtek/r8169_main.c +0 -0
@@ -634,6 +634,8 @@ struct rtl8169_private {
struct rtl_fw *rtl_fw;
u32 ocp_base;
+
+ int retry_probeing;
};
typedef void (*rtl_generic_fct)(struct rtl8169_private *tp);
@@ -5097,13 +5099,16 @@ static int r8169_mdio_register(struct rtl8169_private *tp)
tp->phydev = mdiobus_get_phy(new_bus, 0);
if (!tp->phydev) {
return -ENODEV;
- } else if (!tp->phydev->drv) {
- /* Most chip versions fail with the genphy driver.
- * Therefore ensure that the dedicated PHY driver is loaded.
+ } else if (tp->phydev->phy_id != RTL_GIGA_MAC_NONE) {
+ /* Most chip versions fail with the genphy driver, BUT do rerport valid IW
+ * ID. Re-starting the module seem to fix the issue of non-functional driver.
*/
- dev_err(&pdev->dev, "no dedicated PHY driver found for PHY ID 0x%08x, maybe realtek.ko needs to be added to initramfs?\n", + dev_err(&pdev->dev,
+ "no dedicated driver, but HW found: PHY PHY ID 0x%08x\n",
tp->phydev->phy_id);
- return -EUNATCH;
+
+ dev_err(&pdev->dev, "trying re-probe few times..\n");
+
}
tp->phydev->mac_managed_pm = 1;
@@ -5250,6 +5255,7 @@ static int rtl_init_one(struct pci_dev *pdev, const struct pci_device_id *ent)
enum mac_version chipset;
struct net_device *dev;
u16 xid;
+ int savederr = 0;
dev = devm_alloc_etherdev(&pdev->dev, sizeof (*tp));
if (!dev)
@@ -5261,6 +5267,7 @@ static int rtl_init_one(struct pci_dev *pdev, const struct pci_device_id *ent)
tp->dev = dev;
tp->pci_dev = pdev;
tp->supports_gmii = ent->driver_data == RTL_CFG_NO_GBIT ? 0 : 1;
+ tp->retry_probeing = 0;
tp->eee_adv = -1;
tp->ocp_base = OCP_STD_PHY_BASE;
@@ -5410,7 +5417,15 @@ static int rtl_init_one(struct pci_dev *pdev, const struct pci_device_id *ent)
pci_set_drvdata(pdev, tp);
- rc = r8169_mdio_register(tp);
+ savederr = r8169_mdio_register(tp);
+
+ if (
+ (tp->retry_probeing > 0) &&
+ (savederr == -EAGAIN)
+ ) {
+ netdev_info(dev, " retry of probe requested..............");
+ }
+
if (rc)
return rc;
@@ -5435,6 +5450,14 @@ static int rtl_init_one(struct pci_dev *pdev, const struct pci_device_id *ent)
if (pci_dev_run_wake(pdev))
pm_runtime_put_sync(&pdev->dev);
+ if (
+ (tp->retry_probeing > 0) &&
+ (savederr == -EAGAIN)
+ ) {
+ netdev_info(dev, " retry of probe requested..............");
+ return savederr;
+ }
+
return 0;
}
linux-5.14-rc4/drivers/net/phy/phy_device.c +0 -0
@@ -2980,6 +2980,9 @@ struct fwnode_handle *fwnode_get_phy_node(struct fwnode_handle *fwnode)
}
EXPORT_SYMBOL_GPL(fwnode_get_phy_node);
+
+static int phy_remove(struct device *dev);
+
/**
* phy_probe - probe and init a PHY device
* @dev: device to probe and init
@@ -2988,13 +2991,22 @@ EXPORT_SYMBOL_GPL(fwnode_get_phy_node); * set the state to READY (the driver's init function should * set it to STARTING if needed).
*/
+#define REDO_PROBE_TIMES 5
static int phy_probe(struct device *dev)
{
struct phy_device *phydev = to_phy_device(dev); struct device_driver *drv = phydev->mdio.dev.driver; struct phy_driver *phydrv = to_phy_driver(drv); + int again = 0;
+ int savederr = 0;
+again_retry:
int err = 0;
+ if (again > 0) {
+ pr_err("%s: Re-probe %d of driver.....\n",
+ phydrv->name, again);
+ }
+
phydev->drv = phydrv;
/* Disable the interrupt if the PHY doesn't support it @@ -3013,6 +3025,17 @@ static int phy_probe(struct device *dev)
if (phydev->drv->probe) {
err = phydev->drv->probe(phydev);
+
+ /* If again requested. */
+ if (err == -EAGAIN) {
+ again++;
+ savederr = err;
+ err = 0;
+
+ pr_info("%s: EAGAIN: %d ...\n",
+ phydrv->name, again);
+ }
+
if (err)
goto out;
}
@@ -3081,6 +3104,20 @@ static int phy_probe(struct device *dev)
mutex_unlock(&phydev->lock);
+ if ((savederr == -EAGAIN) &&
+ ((again > 0) && (again < REDO_PROBE_TIMES)) + ) {
+ pr_err("%s: Retry removal driver..\n",
+ phydrv->name);
+
+ phy_remove(dev);
+
+ pr_err("%s: Re-probe driver..\n",
+ phydrv->name);
+ savederr = 0;
+ goto again_retry;
+ }
+
return err;
}
@@ -3108,6 +3145,7 @@ static int phy_remove(struct device *dev) return 0;
}
+
static void phy_shutdown(struct device *dev)
{
struct phy_device *phydev = to_phy_device(dev);
Signature · 1 line
2.17.1