Skip to contentSkip to conversation

iio: chemical: atlas-sensor: add DO support

PATCH Superseded Matt Ranostay 1 participant 4 messages Feb 7, 2020

Subsystems (2)

v5 of 7 Superseded Latest is v7 →

lore
Share & tools
lore
#0 lore raw

v5 cover iio: chemical: atlas-sensor: add DO support

Changes from v1:
* combined dt binding docs
* added making interrupt line is optional patchset
* broke out dt changes from DO-SM module patchset

Change from v2:
* switch docs to YAML format

Change from v3:
* fix up issues reported with dt-schema

Change from v4:
* fix logic issue in optional interrupt patchset

Matt Ranostay (3):
iio: chemical: atlas-sensor: allow probe without interrupt line
iio: chemical: atlas-sensor: add DO-SM module support
dt-bindings: iio: chemical: consolidate atlas-sensor docs

 .../bindings/iio/chemical/atlas,ec-sm.txt     | 21 -----
 .../bindings/iio/chemical/atlas,orp-sm.txt    | 21 -----
 .../bindings/iio/chemical/atlas,ph-sm.txt     | 21 -----
 .../bindings/iio/chemical/atlas,sensor.yaml   | 53 +++++++++++
 drivers/iio/chemical/atlas-sensor.c           | 91 +++++++++++++++----
 5 files changed, 125 insertions(+), 82 deletions(-)
 delete mode 100644 Documentation/devicetree/bindings/iio/chemical/atlas,ec-sm.txt
 delete mode 100644 Documentation/devicetree/bindings/iio/chemical/atlas,orp-sm.txt
 delete mode 100644 Documentation/devicetree/bindings/iio/chemical/atlas,ph-sm.txt
 create mode 100644 Documentation/devicetree/bindings/iio/chemical/atlas,sensor.yaml
Signature · 1 line
2.20.1
#1 lore raw

PATCH v5 1/3 iio: chemical: atlas-sensor: allow probe without interrupt line

Sensors don't actually need a interrupt line to give valid readings, and can triggered with CONFIG_IIO_HRTIMER_TRIGGER as well. Remove the required check for interrupt, and continue along in the probe function.

---
 drivers/iio/chemical/atlas-sensor.c | 27 ++++++++++++---------------
 1 file changed, 12 insertions(+), 15 deletions(-)
drivers/iio/chemical/atlas-sensor.c +12 -15
index 2f0a6fed2589..9a1ab9f8fcc5 100644
@@ -572,11 +572,6 @@ static int atlas_probe(struct i2c_client *client,
 	if (ret)
 		return ret;
 
-	if (client->irq <= 0) {
-		dev_err(&client->dev, "no valid irq defined\n");
-		return -EINVAL;
-	}
-
 	ret = chip->calibration(data);
 	if (ret)
 		return ret;
@@ -596,16 +591,18 @@ static int atlas_probe(struct i2c_client *client,
 
 	init_irq_work(&data->work, atlas_work_handler);
 
-	/* interrupt pin toggles on new conversion */
-	ret = devm_request_threaded_irq(&client->dev, client->irq,
-					NULL, atlas_interrupt_handler,
-					IRQF_TRIGGER_RISING |
-					IRQF_TRIGGER_FALLING | IRQF_ONESHOT,
-					"atlas_irq",
-					indio_dev);
-	if (ret) {
-		dev_err(&client->dev, "request irq (%d) failed\n", client->irq);
-		goto unregister_buffer;
+	if (client->irq > 0) {
+		/* interrupt pin toggles on new conversion */
+		ret = devm_request_threaded_irq(&client->dev, client->irq,
+				NULL, atlas_interrupt_handler,
+				IRQF_TRIGGER_RISING |
+				IRQF_TRIGGER_FALLING | IRQF_ONESHOT,
+				"atlas_irq",
+				indio_dev);
+
+		if (ret)
+			dev_warn(&client->dev,
+				"request irq (%d) failed\n", client->irq);
 	}
 
 	ret = atlas_set_powermode(data, 1);
Signature · 1 line
2.20.1
#2 lore raw

PATCH v5 2/3 iio: chemical: atlas-sensor: add DO-SM module support

In reply to Matt Ranostay

Atlas Scientific DO-SM OEM sensor reads disolved oxygen in a solution. This is reported back as mg/L which maps direc to ppm and so the IIO_CONCENTRATION channel type can be used.

---
 drivers/iio/chemical/atlas-sensor.c | 64 +++++++++++++++++++++++++++--
 1 file changed, 60 insertions(+), 4 deletions(-)
drivers/iio/chemical/atlas-sensor.c +60 -4
index 9a1ab9f8fcc5..363b33f3f43b 100644
@@ -48,6 +48,11 @@
 #define ATLAS_REG_EC_CALIB_STATUS_LOW		BIT(2)
 #define ATLAS_REG_EC_CALIB_STATUS_HIGH		BIT(3)
 
+#define ATLAS_REG_DO_CALIB_STATUS		0x09
+#define ATLAS_REG_DO_CALIB_STATUS_MASK		0x03
+#define ATLAS_REG_DO_CALIB_STATUS_PRESSURE	BIT(0)
+#define ATLAS_REG_DO_CALIB_STATUS_DO		BIT(1)
+
 #define ATLAS_REG_PH_TEMP_DATA		0x0e
 #define ATLAS_REG_PH_DATA		0x16
 
@@ -60,14 +65,19 @@
 #define ATLAS_REG_ORP_CALIB_STATUS	0x0d
 #define ATLAS_REG_ORP_DATA		0x0e
 
+#define ATLAS_REG_DO_TEMP_DATA		0x12
+#define ATLAS_REG_DO_DATA		0x22
+
 #define ATLAS_PH_INT_TIME_IN_MS		450
 #define ATLAS_EC_INT_TIME_IN_MS		650
 #define ATLAS_ORP_INT_TIME_IN_MS	450
+#define ATLAS_DO_INT_TIME_IN_MS		450
 
 enum {
 	ATLAS_PH_SM,
 	ATLAS_EC_SM,
 	ATLAS_ORP_SM,
+	ATLAS_DO_SM,
 };
 
 struct atlas_data {
@@ -121,7 +131,7 @@ static const struct iio_chan_spec atlas_ph_channels[] = {
 	},
 };
 
-#define ATLAS_EC_CHANNEL(_idx, _addr) \
+#define ATLAS_CONCENTRATION_CHANNEL(_idx, _addr) \
 	{\
 		.type = IIO_CONCENTRATION, \
 		.indexed = 1, \
@@ -152,8 +162,8 @@ static const struct iio_chan_spec atlas_ec_channels[] = {
 			.endianness = IIO_BE,
 		},
 	},
-	ATLAS_EC_CHANNEL(0, ATLAS_REG_TDS_DATA),
-	ATLAS_EC_CHANNEL(1, ATLAS_REG_PSS_DATA),
+	ATLAS_CONCENTRATION_CHANNEL(0, ATLAS_REG_TDS_DATA),
+	ATLAS_CONCENTRATION_CHANNEL(1, ATLAS_REG_PSS_DATA),
 	IIO_CHAN_SOFT_TIMESTAMP(3),
 	{
 		.type = IIO_TEMP,
@@ -182,6 +192,19 @@ static const struct iio_chan_spec atlas_orp_channels[] = {
 	IIO_CHAN_SOFT_TIMESTAMP(1),
 };
 
+static const struct iio_chan_spec atlas_do_channels[] = {
+	ATLAS_CONCENTRATION_CHANNEL(0, ATLAS_REG_DO_DATA),
+	IIO_CHAN_SOFT_TIMESTAMP(1),
+	{
+		.type = IIO_TEMP,
+		.address = ATLAS_REG_DO_TEMP_DATA,
+		.info_mask_separate =
+			BIT(IIO_CHAN_INFO_RAW) | BIT(IIO_CHAN_INFO_SCALE),
+		.output = 1,
+		.scan_index = -1
+	},
+};
+
 static int atlas_check_ph_calibration(struct atlas_data *data)
 {
 	struct device *dev = &data->client->dev;
@@ -262,7 +285,31 @@ static int atlas_check_orp_calibration(struct atlas_data *data)
 		dev_warn(dev, "device has not been calibrated\n");
 
 	return 0;
-};
+}
+
+static int atlas_check_do_calibration(struct atlas_data *data)
+{
+	struct device *dev = &data->client->dev;
+	int ret;
+	unsigned int val;
+
+	ret = regmap_read(data->regmap, ATLAS_REG_DO_CALIB_STATUS, &val);
+	if (ret)
+		return ret;
+
+	if (!(val & ATLAS_REG_DO_CALIB_STATUS_MASK)) {
+		dev_warn(dev, "device has not been calibrated\n");
+		return 0;
+	}
+
+	if (!(val & ATLAS_REG_DO_CALIB_STATUS_PRESSURE))
+		dev_warn(dev, "device missing atmospheric pressure calibration\n");
+
+	if (!(val & ATLAS_REG_DO_CALIB_STATUS_DO))
+		dev_warn(dev, "device missing dissolved oxygen calibration\n");
+
+	return 0;
+}
 
 struct atlas_device {
 	const struct iio_chan_spec *channels;
@@ -295,6 +342,13 @@ static struct atlas_device atlas_devices[] = {
 				.calibration = &atlas_check_orp_calibration,
 				.delay = ATLAS_ORP_INT_TIME_IN_MS,
 	},
+	[ATLAS_DO_SM] = {
+				.channels = atlas_do_channels,
+				.num_channels = 3,
+				.data_reg = ATLAS_REG_DO_DATA,
+				.calibration = &atlas_check_do_calibration,
+				.delay = ATLAS_DO_INT_TIME_IN_MS,
+	},
 };
 
 static int atlas_set_powermode(struct atlas_data *data, int on)
@@ -507,6 +561,7 @@ static const struct i2c_device_id atlas_id[] = {
 	{ "atlas-ph-sm", ATLAS_PH_SM},
 	{ "atlas-ec-sm", ATLAS_EC_SM},
 	{ "atlas-orp-sm", ATLAS_ORP_SM},
+	{ "atlas-do-sm", ATLAS_DO_SM},
 	{}
 };
 MODULE_DEVICE_TABLE(i2c, atlas_id);
@@ -515,6 +570,7 @@ static const struct of_device_id atlas_dt_ids[] = {
 	{ .compatible = "atlas,ph-sm", .data = (void *)ATLAS_PH_SM, },
 	{ .compatible = "atlas,ec-sm", .data = (void *)ATLAS_EC_SM, },
 	{ .compatible = "atlas,orp-sm", .data = (void *)ATLAS_ORP_SM, },
+	{ .compatible = "atlas,do-sm", .data = (void *)ATLAS_DO_SM, },
 	{ }
 };
 MODULE_DEVICE_TABLE(of, atlas_dt_ids);
Signature · 1 line
2.20.1
#3 lore raw

PATCH v5 3/3 dt-bindings: iio: chemical: consolidate atlas-sensor docs

In reply to Matt Ranostay

Since Atlas Scientific device support only varies from the compatible string is ideal all the respective docs are merged into a single doc named atlas,sensor.yaml

---
 .../bindings/iio/chemical/atlas,ec-sm.txt     | 21 --------
 .../bindings/iio/chemical/atlas,orp-sm.txt    | 21 --------
 .../bindings/iio/chemical/atlas,ph-sm.txt     | 21 --------
 .../bindings/iio/chemical/atlas,sensor.yaml   | 53 +++++++++++++++++++
 4 files changed, 53 insertions(+), 63 deletions(-)
 delete mode 100644 Documentation/devicetree/bindings/iio/chemical/atlas,ec-sm.txt
 delete mode 100644 Documentation/devicetree/bindings/iio/chemical/atlas,orp-sm.txt
 delete mode 100644 Documentation/devicetree/bindings/iio/chemical/atlas,ph-sm.txt
 create mode 100644 Documentation/devicetree/bindings/iio/chemical/atlas,sensor.yaml
Documentation/devicetree/bindings/iio/chemical/atlas,ec-sm.txt deleted +0 -21
deleted file mode 100644
index f4320595b851..000000000000
@@ -1,21 +0,0 @@
-* Atlas Scientific EC-SM OEM sensor
-
-http://www.atlas-scientific.com/_files/_datasheets/_oem/EC_oem_datasheet.pdf
-
-Required properties:
-
-  - compatible: must be "atlas,ec-sm"
-  - reg: the I2C address of the sensor
-  - interrupts: the sole interrupt generated by the device
-
-  Refer to interrupt-controller/interrupts.txt for generic interrupt client
-  node bindings.
-
-Example:
-
-atlas@64 {
-	compatible = "atlas,ec-sm";
-	reg = <0x64>;
-	interrupt-parent = <&gpio1>;
-	interrupts = <16 2>;
-};
Documentation/devicetree/bindings/iio/chemical/atlas,orp-sm.txt deleted +0 -21
deleted file mode 100644
index af1f5a9aa4da..000000000000
@@ -1,21 +0,0 @@
-* Atlas Scientific ORP-SM OEM sensor
-
-https://www.atlas-scientific.com/_files/_datasheets/_oem/ORP_oem_datasheet.pdf
-
-Required properties:
-
-  - compatible: must be "atlas,orp-sm"
-  - reg: the I2C address of the sensor
-  - interrupts: the sole interrupt generated by the device
-
-  Refer to interrupt-controller/interrupts.txt for generic interrupt client
-  node bindings.
-
-Example:
-
-atlas@66 {
-	compatible = "atlas,orp-sm";
-	reg = <0x66>;
-	interrupt-parent = <&gpio1>;
-	interrupts = <16 2>;
-};
Documentation/devicetree/bindings/iio/chemical/atlas,ph-sm.txt deleted +0 -21
deleted file mode 100644
index 79d90f060327..000000000000
@@ -1,21 +0,0 @@
-* Atlas Scientific pH-SM OEM sensor
-
-http://www.atlas-scientific.com/_files/_datasheets/_oem/pH_oem_datasheet.pdf
-
-Required properties:
-
-  - compatible: must be "atlas,ph-sm"
-  - reg: the I2C address of the sensor
-  - interrupts: the sole interrupt generated by the device
-
-  Refer to interrupt-controller/interrupts.txt for generic interrupt client
-  node bindings.
-
-Example:
-
-atlas@65 {
-	compatible = "atlas,ph-sm";
-	reg = <0x65>;
-	interrupt-parent = <&gpio1>;
-	interrupts = <16 2>;
-};
Documentation/devicetree/bindings/iio/chemical/atlas,sensor.yaml new file +53 -0

53 lines not on this page · raw message

Signature · 1 line
2.20.1