Skip to contentSkip to conversation

xhci fixes for usb-linus

PATCH New Mathias Nyman 1 participant 5 messages Feb 10, 2020

Subsystems (3)
lore
Share & tools
lore
#0 lore raw

cover xhci fixes for usb-linus

Hi Greg

A few xhci fixes resolving an issue entering runtime suspend PCI D3 for some Intel hosts, fixing a memory leak, and forcing max packet size to valid values allowing some older FS devices to function with xhci.

-Mathias

Mathias Nyman (4):
xhci: Force Maximum Packet size for Full-speed bulk devices to valid
range.
xhci: Fix memory leak when caching protocol extended capability PSI
tables
xhci: fix runtime pm enabling for quirky Intel hosts
xhci: apply XHCI_PME_STUCK_QUIRK to Intel Comet Lake platforms

 drivers/usb/host/xhci-hub.c | 25 ++++++++-----
 drivers/usb/host/xhci-mem.c | 70 ++++++++++++++++++++++++-------------
 drivers/usb/host/xhci-pci.c | 10 +++---
 drivers/usb/host/xhci.h     | 14 ++++++--
 4 files changed, 79 insertions(+), 40 deletions(-)
Signature · 1 line
2.17.1
#1 lore raw

PATCH 1/4 xhci: Force Maximum Packet size for Full-speed bulk devices to valid range.

A Full-speed bulk USB audio device (DJ-Tech CTRL) with a invalid Maximum Packet Size of 4 causes a xHC "Parameter Error" at enumeration.

This is because valid Maximum packet sizes for Full-speed bulk endpoints are 8, 16, 32 and 64 bytes. Hosts are not required to support other values than these. See usb 2 specs section 5.8.3 for details.

The device starts working after forcing the maximum packet size to 8. This is most likely the case with other devices as well, so force the maximum packet size to a valid range.

---
 drivers/usb/host/xhci-mem.c | 12 +++++++++---
 1 file changed, 9 insertions(+), 3 deletions(-)
drivers/usb/host/xhci-mem.c +9 -3
index 3b1388fa2f36..0e2701649369 100644
@@ -1475,9 +1475,15 @@ int xhci_endpoint_init(struct xhci_hcd *xhci,
 	/* Allow 3 retries for everything but isoc, set CErr = 3 */
 	if (!usb_endpoint_xfer_isoc(&ep->desc))
 		err_count = 3;
-	/* Some devices get this wrong */
-	if (usb_endpoint_xfer_bulk(&ep->desc) && udev->speed == USB_SPEED_HIGH)
-		max_packet = 512;
+	/* HS bulk max packet should be 512, FS bulk supports 8, 16, 32 or 64 */
+	if (usb_endpoint_xfer_bulk(&ep->desc)) {
+		if (udev->speed == USB_SPEED_HIGH)
+			max_packet = 512;
+		if (udev->speed == USB_SPEED_FULL) {
+			max_packet = rounddown_pow_of_two(max_packet);
+			max_packet = clamp_val(max_packet, 8, 64);
+		}
+	}
 	/* xHCI 1.0 and 1.1 indicates that ctrl ep avg TRB Length should be 8 */
 	if (usb_endpoint_xfer_control(&ep->desc) && xhci->hci_version >= 0x100)
 		avg_trb_len = 8;
Signature · 1 line
2.17.1
#2 lore raw

PATCH 2/4 xhci: Fix memory leak when caching protocol extended capability PSI tables

In reply to Mathias Nyman

xhci driver assumed that xHC controllers have at most one custom supported speed table (PSI) for all usb 3.x ports.
Memory was allocated for one PSI table under the xhci hub structure.

Turns out this is not the case, some controllers have a separate "supported protocol capability" entry with a PSI table for each port. This means each usb3 roothub port can in theory support different custom speeds.

To solve this, cache all supported protocol capabilities with their PSI tables in an array, and add pointers to the xhci port structure so that every port points to its capability entry in the array.

When creating the SuperSpeedPlus USB Device Capability BOS descriptor for the xhci USB 3.1 roothub we for now will use only data from the first USB 3.1 capable protocol capability entry in the array. This could be improved later, this patch focuses resolving the memory leak.

Fixes 47189098f8be ("xhci: parse xhci protocol speed ID list for usb 3.1 usage")
Cc stable <[email protected]> # v4.4+
---
 drivers/usb/host/xhci-hub.c | 25 +++++++++++-----
 drivers/usb/host/xhci-mem.c | 58 +++++++++++++++++++++++--------------
 drivers/usb/host/xhci.h     | 14 +++++++--
 3 files changed, 64 insertions(+), 33 deletions(-)
drivers/usb/host/xhci-hub.c +17 -8
index 7a3a29e5e9d2..af92b2576fe9 100644
@@ -55,6 +55,7 @@ static u8 usb_bos_descriptor [] = {
 static int xhci_create_usb3_bos_desc(struct xhci_hcd *xhci, char *buf,
 				     u16 wLength)
 {
+	struct xhci_port_cap *port_cap = NULL;
 	int i, ssa_count;
 	u32 temp;
 	u16 desc_size, ssp_cap_size, ssa_size = 0;
@@ -64,16 +65,24 @@ static int xhci_create_usb3_bos_desc(struct xhci_hcd *xhci, char *buf,
 	ssp_cap_size = sizeof(usb_bos_descriptor) - desc_size;
 
 	/* does xhci support USB 3.1 Enhanced SuperSpeed */
-	if (xhci->usb3_rhub.min_rev >= 0x01) {
+	for (i = 0; i < xhci->num_port_caps; i++) {
+		if (xhci->port_caps[i].maj_rev == 0x03 &&
+		    xhci->port_caps[i].min_rev >= 0x01) {
+			usb3_1 = true;
+			port_cap = &xhci->port_caps[i];
+			break;
+		}
+	}
+
+	if (usb3_1) {
 		/* does xhci provide a PSI table for SSA speed attributes? */
-		if (xhci->usb3_rhub.psi_count) {
+		if (port_cap->psi_count) {
 			/* two SSA entries for each unique PSI ID, RX and TX */
-			ssa_count = xhci->usb3_rhub.psi_uid_count * 2;
+			ssa_count = port_cap->psi_uid_count * 2;
 			ssa_size = ssa_count * sizeof(u32);
 			ssp_cap_size -= 16; /* skip copying the default SSA */
 		}
 		desc_size += ssp_cap_size;
-		usb3_1 = true;
 	}
 	memcpy(buf, &usb_bos_descriptor, min(desc_size, wLength));
 
@@ -99,7 +108,7 @@ static int xhci_create_usb3_bos_desc(struct xhci_hcd *xhci, char *buf,
 	}
 
 	/* If PSI table exists, add the custom speed attributes from it */
-	if (usb3_1 && xhci->usb3_rhub.psi_count) {
+	if (usb3_1 && port_cap->psi_count) {
 		u32 ssp_cap_base, bm_attrib, psi, psi_mant, psi_exp;
 		int offset;
 
@@ -111,7 +120,7 @@ static int xhci_create_usb3_bos_desc(struct xhci_hcd *xhci, char *buf,
 
 		/* attribute count SSAC bits 4:0 and ID count SSIC bits 8:5 */
 		bm_attrib = (ssa_count - 1) & 0x1f;
-		bm_attrib |= (xhci->usb3_rhub.psi_uid_count - 1) << 5;
+		bm_attrib |= (port_cap->psi_uid_count - 1) << 5;
 		put_unaligned_le32(bm_attrib, &buf[ssp_cap_base + 4]);
 
 		if (wLength < desc_size + ssa_size)
@@ -124,8 +133,8 @@ static int xhci_create_usb3_bos_desc(struct xhci_hcd *xhci, char *buf,
 		 * USB 3.1 requires two SSA entries (RX and TX) for every link
 		 */
 		offset = desc_size;
-		for (i = 0; i < xhci->usb3_rhub.psi_count; i++) {
-			psi = xhci->usb3_rhub.psi[i];
+		for (i = 0; i < port_cap->psi_count; i++) {
+			psi = port_cap->psi[i];
 			psi &= ~USB_SSP_SUBLINK_SPEED_RSVD;
 			psi_exp = XHCI_EXT_PORT_PSIE(psi);
 			psi_mant = XHCI_EXT_PORT_PSIM(psi);
drivers/usb/host/xhci-mem.c +36 -22

102 lines not on this page · raw message

drivers/usb/host/xhci.h +11 -3
index 13d8838cd552..3ecee10fdcdc 100644
@@ -1702,12 +1702,20 @@ struct xhci_bus_state {
  * Intel Lynx Point LP xHCI host.
  */
 #define	XHCI_MAX_REXIT_TIMEOUT_MS	20
+struct xhci_port_cap {
+	u32			*psi;	/* array of protocol speed ID entries */
+	u8			psi_count;
+	u8			psi_uid_count;
+	u8			maj_rev;
+	u8			min_rev;
+};
 
 struct xhci_port {
 	__le32 __iomem		*addr;
 	int			hw_portnum;
 	int			hcd_portnum;
 	struct xhci_hub		*rhub;
+	struct xhci_port_cap	*port_cap;
 };
 
 struct xhci_hub {
@@ -1719,9 +1727,6 @@ struct xhci_hub {
 	/* supported prococol extended capabiliy values */
 	u8			maj_rev;
 	u8			min_rev;
-	u32			*psi;	/* array of protocol speed ID entries */
-	u8			psi_count;
-	u8			psi_uid_count;
 };
 
 /* There is one xhci_hcd structure per controller */
@@ -1880,6 +1885,9 @@ struct xhci_hcd {
 	/* cached usb2 extened protocol capabilites */
 	u32                     *ext_caps;
 	unsigned int            num_ext_caps;
+	/* cached extended protocol port capabilities */
+	struct xhci_port_cap	*port_caps;
+	unsigned int		num_port_caps;
 	/* Compliance Mode Recovery Data */
 	struct timer_list	comp_mode_recovery_timer;
 	u32			port_status_u0;
Signature · 1 line
2.17.1
#3 lore raw

PATCH 3/4 xhci: fix runtime pm enabling for quirky Intel hosts

In reply to Mathias Nyman

Intel hosts that need the XHCI_PME_STUCK_QUIRK flag should enable runtime pm by calling xhci_pme_acpi_rtd3_enable() before usb_hcd_pci_probe() calls pci_dev_run_wake().
Otherwise usage count for the device won't be decreased, and runtime suspend is prevented.

usb_hcd_pci_probe() only decreases the usage count if device can generate run-time wake-up events, i.e. when pci_dev_run_wake() returns true.

This issue was exposed by pci_dev_run_wake() change in commit 8feaec33b986 ("PCI / PM: Always check PME wakeup capability for runtime wakeup support")
and should be backported to kernels with that change

---
 drivers/usb/host/xhci-pci.c | 6 +++---
 1 file changed, 3 insertions(+), 3 deletions(-)
drivers/usb/host/xhci-pci.c +3 -3
index 4917c5b033fa..da7c2db41671 100644
@@ -302,6 +302,9 @@ static int xhci_pci_setup(struct usb_hcd *hcd)
 	if (!usb_hcd_is_primary_hcd(hcd))
 		return 0;
 
+	if (xhci->quirks & XHCI_PME_STUCK_QUIRK)
+		xhci_pme_acpi_rtd3_enable(pdev);
+
 	xhci_dbg(xhci, "Got SBRN %u\n", (unsigned int) xhci->sbrn);
 
 	/* Find any debug ports */
@@ -359,9 +362,6 @@ static int xhci_pci_probe(struct pci_dev *dev, const struct pci_device_id *id)
 			HCC_MAX_PSA(xhci->hcc_params) >= 4)
 		xhci->shared_hcd->can_do_streams = 1;
 
-	if (xhci->quirks & XHCI_PME_STUCK_QUIRK)
-		xhci_pme_acpi_rtd3_enable(dev);
-
 	/* USB-2 and USB-3 roothubs initialized, allow runtime pm suspend */
 	pm_runtime_put_noidle(&dev->dev);
 
Signature · 1 line
2.17.1
#4 lore raw

PATCH 4/4 xhci: apply XHCI_PME_STUCK_QUIRK to Intel Comet Lake platforms

In reply to Mathias Nyman

Intel Comet Lake based platform require the XHCI_PME_STUCK_QUIRK quirk as well. Without this xHC can not enter D3 in runtime suspend.

---
 drivers/usb/host/xhci-pci.c | 4 +++-
 1 file changed, 3 insertions(+), 1 deletion(-)
drivers/usb/host/xhci-pci.c +3 -1
index da7c2db41671..5e9b537df631 100644
@@ -49,6 +49,7 @@
 #define PCI_DEVICE_ID_INTEL_TITAN_RIDGE_4C_XHCI		0x15ec
 #define PCI_DEVICE_ID_INTEL_TITAN_RIDGE_DD_XHCI		0x15f0
 #define PCI_DEVICE_ID_INTEL_ICE_LAKE_XHCI		0x8a13
+#define PCI_DEVICE_ID_INTEL_CML_XHCI			0xa3af
 
 #define PCI_DEVICE_ID_AMD_PROMONTORYA_4			0x43b9
 #define PCI_DEVICE_ID_AMD_PROMONTORYA_3			0x43ba
@@ -187,7 +188,8 @@ static void xhci_pci_quirks(struct device *dev, struct xhci_hcd *xhci)
 		 pdev->device == PCI_DEVICE_ID_INTEL_BROXTON_M_XHCI ||
 		 pdev->device == PCI_DEVICE_ID_INTEL_BROXTON_B_XHCI ||
 		 pdev->device == PCI_DEVICE_ID_INTEL_APL_XHCI ||
-		 pdev->device == PCI_DEVICE_ID_INTEL_DNV_XHCI)) {
+		 pdev->device == PCI_DEVICE_ID_INTEL_DNV_XHCI ||
+		 pdev->device == PCI_DEVICE_ID_INTEL_CML_XHCI)) {
 		xhci->quirks |= XHCI_PME_STUCK_QUIRK;
 	}
 	if (pdev->vendor == PCI_VENDOR_ID_INTEL &&
Signature · 1 line
2.17.1