Skip to contentSkip to conversation

x86: improve assisted tlb flush and use it in guest mode

PATCH Superseded Roger Pau Monne 4 participants 19 messages Feb 10, 2020 – Feb 18, 2020

v4 of 11 Superseded Latest is v11 →

lore
Share & tools
lore
#0 lore raw

v4 cover x86: improve assisted tlb flush and use it in guest mode

Hello,

The following series aims to improve the TLB flush times when running nested Xen, and it's specially beneficial when running in shim mode.

Only the HAP guest TLB flush is improved, the shadow paging TLB flush is left as-is, and can be improved later if there's interest.

For a reference on the performance improvement see patch #7, as it's a huge increase which can benefit other guests using assisted TLB flushes, and also the ones using the viridian TLB flush assist (ie: Windows).

Thanks, Roger.

Roger Pau Monne (7):
x86/hvm: allow ASID flush when v != current x86/paging: add TLB flush hooks
x86/hap: improve hypervisor assisted guest TLB flush x86/tlb: introduce a flush guests TLB flag x86/tlb: allow disabling the TLB clock xen/guest: prepare hypervisor ops to use alternative calls x86/tlb: use Xen L0 assisted TLB flush when available

 xen/arch/x86/flushtlb.c                | 24 ++++++---
 xen/arch/x86/guest/hyperv/hyperv.c     |  2 +-
 xen/arch/x86/guest/hypervisor.c        | 51 ++++++++++--------
 xen/arch/x86/guest/xen/xen.c           |  8 ++-
 xen/arch/x86/hvm/asid.c                |  6 +--
 xen/arch/x86/hvm/hvm.c                 | 51 ++----------------
 xen/arch/x86/mm/hap/hap.c              | 52 +++++++++++++++++++
 xen/arch/x86/mm/shadow/common.c        | 71 +++++++++++++++++++++++---
 xen/arch/x86/mm/shadow/hvm.c           |  2 +-
 xen/arch/x86/mm/shadow/multi.c         | 16 +++---
 xen/arch/x86/smp.c                     | 11 ++++
 xen/include/asm-x86/flushtlb.h         | 19 ++++++-
 xen/include/asm-x86/guest/hypervisor.h | 17 ++++++
 xen/include/asm-x86/hap.h              |  3 ++
 xen/include/asm-x86/shadow.h           | 12 +++++
 15 files changed, 246 insertions(+), 99 deletions(-)
Signature · 7 lines
2.25.0


_______________________________________________
Xen-devel mailing list
[email protected]
https://lists.xenproject.org/mailman/listinfo/xen-devel
#1 lore raw

PATCH v4 1/7 x86/hvm: allow ASID flush when v != current

Current implementation of hvm_asid_flush_vcpu is not safe to use unless the target vCPU is either paused or the currently running one, as it modifies the generation without any locking.

Fix this by using atomic operations when accessing the generation field, both in hvm_asid_flush_vcpu_asid and other ASID functions. This allows to safely flush the current ASID generation. Note that for the flush to take effect if the vCPU is currently running a vmexit is required.

Note the same could be achieved by introducing an extra field to hvm_vcpu_asid that signals hvm_asid_handle_vmenter the need to call hvm_asid_flush_vcpu on the given vCPU before vmentry, this however seems unnecessary as hvm_asid_flush_vcpu itself only sets two vCPU fields to 0, so there's no need to delay this to the vmentry ASID helper.

This is not a bugfix as no callers that would violate the assumptions listed in the first paragraph have been found, but a preparatory change in order to allow remote flushing of HVM vCPUs.

---
 xen/arch/x86/hvm/asid.c | 6 +++---
 1 file changed, 3 insertions(+), 3 deletions(-)
xen/arch/x86/hvm/asid.c +3 -3
index 8e00a28443..63ce462d56 100644
@@ -83,7 +83,7 @@ void hvm_asid_init(int nasids)
 
 void hvm_asid_flush_vcpu_asid(struct hvm_vcpu_asid *asid)
 {
-    asid->generation = 0;
+    write_atomic(&asid->generation, 0);
 }
 
 void hvm_asid_flush_vcpu(struct vcpu *v)
@@ -121,7 +121,7 @@ bool_t hvm_asid_handle_vmenter(struct hvm_vcpu_asid *asid)
         goto disabled;
 
     /* Test if VCPU has valid ASID. */
-    if ( asid->generation == data->core_asid_generation )
+    if ( read_atomic(&asid->generation) == data->core_asid_generation )
         return 0;
 
     /* If there are no free ASIDs, need to go to a new generation */
@@ -135,7 +135,7 @@ bool_t hvm_asid_handle_vmenter(struct hvm_vcpu_asid *asid)
 
     /* Now guaranteed to be a free ASID. */
     asid->asid = data->next_asid++;
-    asid->generation = data->core_asid_generation;
+    write_atomic(&asid->generation, data->core_asid_generation);
 
     /*
      * When we assign ASID 1, flush all TLB entries as we are starting a new
Signature · 7 lines
2.25.0


_______________________________________________
Xen-devel mailing list
[email protected]
https://lists.xenproject.org/mailman/listinfo/xen-devel
#2 lore raw

PATCH v4 2/7 x86/paging: add TLB flush hooks

In reply to Roger Pau Monne

Add shadow and hap implementation specific helpers to perform guest TLB flushes. Note that the code for both is exactly the same at the moment, and is copied from hvm_flush_vcpu_tlb. This will be changed by further patches that will add implementation specific optimizations to them.

No functional change intended.

---
Changes since v3:
- Fix stray newline removal.
- Fix return of shadow_flush_tlb dummy function.

---
 xen/arch/x86/hvm/hvm.c          | 51 ++----------------------------
 xen/arch/x86/mm/hap/hap.c       | 54 ++++++++++++++++++++++++++++++++
 xen/arch/x86/mm/shadow/common.c | 55 +++++++++++++++++++++++++++++++++
 xen/include/asm-x86/hap.h       |  3 ++
 xen/include/asm-x86/shadow.h    | 12 +++++++
 5 files changed, 127 insertions(+), 48 deletions(-)
xen/arch/x86/hvm/hvm.c +3 -48
index 00a9e70b7c..4049f57232 100644
@@ -3990,55 +3990,10 @@ static void hvm_s3_resume(struct domain *d)
 bool hvm_flush_vcpu_tlb(bool (*flush_vcpu)(void *ctxt, struct vcpu *v),
                         void *ctxt)
 {
-    static DEFINE_PER_CPU(cpumask_t, flush_cpumask);
-    cpumask_t *mask = &this_cpu(flush_cpumask);
-    struct domain *d = current->domain;
-    struct vcpu *v;
-
-    /* Avoid deadlock if more than one vcpu tries this at the same time. */
-    if ( !spin_trylock(&d->hypercall_deadlock_mutex) )
-        return false;
-
-    /* Pause all other vcpus. */
-    for_each_vcpu ( d, v )
-        if ( v != current && flush_vcpu(ctxt, v) )
-            vcpu_pause_nosync(v);
-
-    /* Now that all VCPUs are signalled to deschedule, we wait... */
-    for_each_vcpu ( d, v )
-        if ( v != current && flush_vcpu(ctxt, v) )
-            while ( !vcpu_runnable(v) && v->is_running )
-                cpu_relax();
-
-    /* All other vcpus are paused, safe to unlock now. */
-    spin_unlock(&d->hypercall_deadlock_mutex);
-
-    cpumask_clear(mask);
-
-    /* Flush paging-mode soft state (e.g., va->gfn cache; PAE PDPE cache). */
-    for_each_vcpu ( d, v )
-    {
-        unsigned int cpu;
-
-        if ( !flush_vcpu(ctxt, v) )
-            continue;
-
-        paging_update_cr3(v, false);
+    struct domain *currd = current->domain;
 
-        cpu = read_atomic(&v->dirty_cpu);
-        if ( is_vcpu_dirty_cpu(cpu) )
-            __cpumask_set_cpu(cpu, mask);
-    }
-
-    /* Flush TLBs on all CPUs with dirty vcpu state. */
-    flush_tlb_mask(mask);
-
-    /* Done. */
-    for_each_vcpu ( d, v )
-        if ( v != current && flush_vcpu(ctxt, v) )
-            vcpu_unpause(v);
-
-    return true;
+    return shadow_mode_enabled(currd) ? shadow_flush_tlb(flush_vcpu, ctxt)
+                                      : hap_flush_tlb(flush_vcpu, ctxt);
 }
 
 static bool always_flush(void *ctxt, struct vcpu *v)
xen/arch/x86/mm/hap/hap.c +54 -0

60 lines not on this page · raw message

xen/arch/x86/mm/shadow/common.c +55 -0

61 lines not on this page · raw message

xen/include/asm-x86/hap.h +3 -0
index b94bfb4ed0..0c6aa26b9b 100644
@@ -46,6 +46,9 @@ int   hap_track_dirty_vram(struct domain *d,
 extern const struct paging_mode *hap_paging_get_mode(struct vcpu *);
 int hap_set_allocation(struct domain *d, unsigned int pages, bool *preempted);
 
+bool hap_flush_tlb(bool (*flush_vcpu)(void *ctxt, struct vcpu *v),
+                   void *ctxt);
+
 #endif /* XEN_HAP_H */
 
 /*
xen/include/asm-x86/shadow.h +12 -0
index 907c71f497..cfd4650a16 100644
@@ -95,6 +95,10 @@ void shadow_blow_tables_per_domain(struct domain *d);
 int shadow_set_allocation(struct domain *d, unsigned int pages,
                           bool *preempted);
 
+/* Flush the TLB of the selected vCPUs. */
+bool shadow_flush_tlb(bool (*flush_vcpu)(void *ctxt, struct vcpu *v),
+                      void *ctxt);
+
 #else /* !CONFIG_SHADOW_PAGING */
 
 #define shadow_teardown(d, p) ASSERT(is_pv_domain(d))
@@ -106,6 +110,14 @@ int shadow_set_allocation(struct domain *d, unsigned int pages,
 #define shadow_set_allocation(d, pages, preempted) \
     ({ ASSERT_UNREACHABLE(); -EOPNOTSUPP; })
 
+static inline bool shadow_flush_tlb(bool (*flush_vcpu)(void *ctxt,
+                                                       struct vcpu *v),
+                                    void *ctxt)
+{
+    ASSERT_UNREACHABLE();
+    return false;
+}
+
 static inline void sh_remove_shadows(struct domain *d, mfn_t gmfn,
                                      int fast, int all) {}
 
Signature · 7 lines
2.25.0


_______________________________________________
Xen-devel mailing list
[email protected]
https://lists.xenproject.org/mailman/listinfo/xen-devel
Acked-by on v4 2/7
#3 lore raw

Re: [Xen-devel] [PATCH v4 2/7] x86/paging: add TLB flush hooks

Quoted 10 lines · Roger Pau Monne

Add shadow and hap implementation specific helpers to perform guest TLB flushes. Note that the code for both is exactly the same at the moment, and is copied from hvm_flush_vcpu_tlb. This will be changed by further patches that will add implementation specific optimizations to them.

No functional change intended.

_______________________________________________
Xen-devel mailing list
[email protected]
https://lists.xenproject.org/mailman/listinfo/xen-devel

Acked-by
#4 lore raw

Re: [Xen-devel] [PATCH v4 2/7] x86/paging: add TLB flush hooks

Quoted 7 lines · Tim Deegan
Quoted 6 lines · Roger Pau Monne

Add shadow and hap implementation specific helpers to perform guest TLB flushes. Note that the code for both is exactly the same at the moment, and is copied from hvm_flush_vcpu_tlb. This will be changed by further patches that will add implementation specific optimizations to them.

Quoted 6 lines
Quoted 4 lines

No functional change intended.

Oops, wrong address, sorry.

_______________________________________________
Xen-devel mailing list
[email protected]
https://lists.xenproject.org/mailman/listinfo/xen-devel

#5 lore raw

PATCH v4 3/7 x86/hap: improve hypervisor assisted guest TLB flush

In reply to Roger Pau Monne

The current implementation of the hypervisor assisted flush for HAP is extremely inefficient.

First of all there's no need to call paging_update_cr3, as the only relevant part of that function when doing a flush is the ASID vCPU flush, so just call that function directly.

Since hvm_asid_flush_vcpu is protected against concurrent callers by using atomic operations there's no need anymore to pause the affected vCPUs.

Finally the global TLB flush performed by flush_tlb_mask is also not necessary, since we only want to flush the guest TLB state it's enough to trigger a vmexit on the pCPUs currently holding any vCPU state, as such vmexit will already perform an ASID/VPID update, and thus clear the guest TLB.

---
Changes since v3:
- s/do_flush/handle_flush/.
- Add comment about handle_flush usage.
- Fix VPID typo in comment.

---
 xen/arch/x86/mm/hap/hap.c | 52 +++++++++++++++++++--------------------
 1 file changed, 25 insertions(+), 27 deletions(-)
xen/arch/x86/mm/hap/hap.c +25 -27
index 6894c1aa38..dbb61bf9c6 100644
@@ -669,32 +669,28 @@ static void hap_update_cr3(struct vcpu *v, int do_locking, bool noflush)
     hvm_update_guest_cr3(v, noflush);
 }
 
+/*
+ * NB: doesn't actually perform any flush, used just to clear the CPU from the
+ * mask and hence signal that the guest TLB flush has been done.
+ */
+static void handle_flush(void *data)
+{
+    cpumask_t *mask = data;
+    unsigned int cpu = smp_processor_id();
+
+    ASSERT(cpumask_test_cpu(cpu, mask));
+    cpumask_clear_cpu(cpu, mask);
+}
+
 bool hap_flush_tlb(bool (*flush_vcpu)(void *ctxt, struct vcpu *v),
                    void *ctxt)
 {
     static DEFINE_PER_CPU(cpumask_t, flush_cpumask);
     cpumask_t *mask = &this_cpu(flush_cpumask);
     struct domain *d = current->domain;
+    unsigned int this_cpu = smp_processor_id();
     struct vcpu *v;
 
-    /* Avoid deadlock if more than one vcpu tries this at the same time. */
-    if ( !spin_trylock(&d->hypercall_deadlock_mutex) )
-        return false;
-
-    /* Pause all other vcpus. */
-    for_each_vcpu ( d, v )
-        if ( v != current && flush_vcpu(ctxt, v) )
-            vcpu_pause_nosync(v);
-
-    /* Now that all VCPUs are signalled to deschedule, we wait... */
-    for_each_vcpu ( d, v )
-        if ( v != current && flush_vcpu(ctxt, v) )
-            while ( !vcpu_runnable(v) && v->is_running )
-                cpu_relax();
-
-    /* All other vcpus are paused, safe to unlock now. */
-    spin_unlock(&d->hypercall_deadlock_mutex);
-
     cpumask_clear(mask);
 
     /* Flush paging-mode soft state (e.g., va->gfn cache; PAE PDPE cache). */
@@ -705,20 +701,22 @@ bool hap_flush_tlb(bool (*flush_vcpu)(void *ctxt, struct vcpu *v),
         if ( !flush_vcpu(ctxt, v) )
             continue;
 
-        paging_update_cr3(v, false);
+        hvm_asid_flush_vcpu(v);
 
         cpu = read_atomic(&v->dirty_cpu);
-        if ( is_vcpu_dirty_cpu(cpu) )
+        if ( cpu != this_cpu && is_vcpu_dirty_cpu(cpu) )
             __cpumask_set_cpu(cpu, mask);
     }
 
-    /* Flush TLBs on all CPUs with dirty vcpu state. */
-    flush_tlb_mask(mask);
-
-    /* Done. */
-    for_each_vcpu ( d, v )
-        if ( v != current && flush_vcpu(ctxt, v) )
-            vcpu_unpause(v);
+    /*
+     * Trigger a vmexit on all pCPUs with dirty vCPU state in order to force an
+     * ASID/VPID change and hence accomplish a guest TLB flush. Note that vCPUs
+     * not currently running will already be flushed when scheduled because of
+     * the ASID tickle done in the loop above.
+     */
+    on_selected_cpus(mask, handle_flush, mask, 0);
+    while ( !cpumask_empty(mask) )
+        cpu_relax();
 
     return true;
 }
Signature · 7 lines
2.25.0


_______________________________________________
Xen-devel mailing list
[email protected]
https://lists.xenproject.org/mailman/listinfo/xen-devel
#6 lore raw

PATCH v4 4/7 x86/tlb: introduce a flush guests TLB flag

In reply to Roger Pau Monne

Introduce a specific flag to request a HVM guest TLB flush, which is an ASID/VPID tickle that forces a linear TLB flush for all HVM guests.

This was previously unconditionally done in each pre_flush call, but that's not required: HVM guests not using shadow don't require linear TLB flushes as Xen doesn't modify the guest page tables in that case (ie: when using HAP).

Modify all shadow code TLB flushes to also flush the guest TLB, in order to keep the previous behavior. I haven't looked at each specific shadow code TLB flush in order to figure out whether it actually requires a guest TLB flush or not, so there might be room for improvement in that regard.

---
 xen/arch/x86/flushtlb.c         |  5 +++--
 xen/arch/x86/mm/shadow/common.c | 18 +++++++++---------
 xen/arch/x86/mm/shadow/hvm.c    |  2 +-
 xen/arch/x86/mm/shadow/multi.c  | 16 ++++++++--------
 xen/include/asm-x86/flushtlb.h  |  2 ++
 5 files changed, 23 insertions(+), 20 deletions(-)
xen/arch/x86/flushtlb.c +3 -2
index 03f92c23dc..e7ccd4ec7b 100644
@@ -59,8 +59,6 @@ static u32 pre_flush(void)
         raise_softirq(NEW_TLBFLUSH_CLOCK_PERIOD_SOFTIRQ);
 
  skip_clocktick:
-    hvm_flush_guest_tlbs();
-
     return t2;
 }
 
@@ -221,6 +219,9 @@ unsigned int flush_area_local(const void *va, unsigned int flags)
             do_tlb_flush();
     }
 
+    if ( flags & FLUSH_GUESTS_TLB )
+        hvm_flush_guest_tlbs();
+
     if ( flags & FLUSH_CACHE )
     {
         const struct cpuinfo_x86 *c = &current_cpu_data;
xen/arch/x86/mm/shadow/common.c +9 -9
index ee90e55b41..2a85e10112 100644
@@ -363,7 +363,7 @@ static int oos_remove_write_access(struct vcpu *v, mfn_t gmfn,
     }
 
     if ( ftlb )
-        flush_tlb_mask(d->dirty_cpumask);
+        flush_mask(d->dirty_cpumask, FLUSH_TLB | FLUSH_GUESTS_TLB);
 
     return 0;
 }
@@ -939,7 +939,7 @@ static void _shadow_prealloc(struct domain *d, unsigned int pages)
                 /* See if that freed up enough space */
                 if ( d->arch.paging.shadow.free_pages >= pages )
                 {
-                    flush_tlb_mask(d->dirty_cpumask);
+                    flush_mask(d->dirty_cpumask, FLUSH_TLB | FLUSH_GUESTS_TLB);
                     return;
                 }
             }
@@ -993,7 +993,7 @@ static void shadow_blow_tables(struct domain *d)
                                pagetable_get_mfn(v->arch.shadow_table[i]), 0);
 
     /* Make sure everyone sees the unshadowings */
-    flush_tlb_mask(d->dirty_cpumask);
+    flush_mask(d->dirty_cpumask, FLUSH_TLB | FLUSH_GUESTS_TLB);
 }
 
 void shadow_blow_tables_per_domain(struct domain *d)
@@ -1102,7 +1102,7 @@ mfn_t shadow_alloc(struct domain *d,
         if ( unlikely(!cpumask_empty(&mask)) )
         {
             perfc_incr(shadow_alloc_tlbflush);
-            flush_tlb_mask(&mask);
+            flush_mask(&mask, FLUSH_TLB | FLUSH_GUESTS_TLB);
         }
         /* Now safe to clear the page for reuse */
         clear_domain_page(page_to_mfn(sp));
@@ -2290,7 +2290,7 @@ void sh_remove_shadows(struct domain *d, mfn_t gmfn, int fast, int all)
 
     /* Need to flush TLBs now, so that linear maps are safe next time we
      * take a fault. */
-    flush_tlb_mask(d->dirty_cpumask);
+    flush_mask(d->dirty_cpumask, FLUSH_TLB | FLUSH_GUESTS_TLB);
 
     paging_unlock(d);
 }
@@ -3005,7 +3005,7 @@ static void sh_unshadow_for_p2m_change(struct domain *d, unsigned long gfn,
         {
             sh_remove_all_shadows_and_parents(d, mfn);
             if ( sh_remove_all_mappings(d, mfn, _gfn(gfn)) )
-                flush_tlb_mask(d->dirty_cpumask);
+                flush_mask(d->dirty_cpumask, FLUSH_TLB | FLUSH_GUESTS_TLB);
         }
     }
 
@@ -3045,7 +3045,7 @@ static void sh_unshadow_for_p2m_change(struct domain *d, unsigned long gfn,
                 }
                 omfn = mfn_add(omfn, 1);
             }
-            flush_tlb_mask(&flushmask);
+            flush_mask(&flushmask, FLUSH_TLB | FLUSH_GUESTS_TLB);
 
             if ( npte )
                 unmap_domain_page(npte);
@@ -3332,7 +3332,7 @@ int shadow_track_dirty_vram(struct domain *d,
         }
     }
     if ( flush_tlb )
-        flush_tlb_mask(d->dirty_cpumask);
+        flush_mask(d->dirty_cpumask, FLUSH_TLB | FLUSH_GUESTS_TLB);
     goto out;
 
 out_sl1ma:
@@ -3402,7 +3402,7 @@ bool shadow_flush_tlb(bool (*flush_vcpu)(void *ctxt, struct vcpu *v),
     }
 
     /* Flush TLBs on all CPUs with dirty vcpu state. */
-    flush_tlb_mask(mask);
+    flush_mask(mask, FLUSH_TLB | FLUSH_GUESTS_TLB);
 
     /* Done. */
     for_each_vcpu ( d, v )
xen/arch/x86/mm/shadow/hvm.c +1 -1
index a219266fa2..64077d181b 100644
@@ -590,7 +590,7 @@ static void validate_guest_pt_write(struct vcpu *v, mfn_t gmfn,
 
     if ( rc & SHADOW_SET_FLUSH )
         /* Need to flush TLBs to pick up shadow PT changes */
-        flush_tlb_mask(d->dirty_cpumask);
+        flush_mask(d->dirty_cpumask, FLUSH_TLB | FLUSH_GUESTS_TLB);
 
     if ( rc & SHADOW_SET_ERROR )
     {
xen/arch/x86/mm/shadow/multi.c +8 -8
index 26798b317c..22aeb97b1e 100644
@@ -3066,7 +3066,7 @@ static int sh_page_fault(struct vcpu *v,
         perfc_incr(shadow_rm_write_flush_tlb);
         smp_wmb();
         atomic_inc(&d->arch.paging.shadow.gtable_dirty_version);
-        flush_tlb_mask(d->dirty_cpumask);
+        flush_mask(d->dirty_cpumask, FLUSH_TLB | FLUSH_GUESTS_TLB);
     }
 
 #if (SHADOW_OPTIMIZATIONS & SHOPT_OUT_OF_SYNC)
@@ -3575,7 +3575,7 @@ static bool sh_invlpg(struct vcpu *v, unsigned long linear)
     if ( mfn_to_page(sl1mfn)->u.sh.type
          == SH_type_fl1_shadow )
     {
-        flush_tlb_local();
+        flush_local(FLUSH_TLB | FLUSH_GUESTS_TLB);
         return false;
     }
 
@@ -3810,7 +3810,7 @@ sh_update_linear_entries(struct vcpu *v)
          * table entry. But, without this change, it would fetch the wrong
          * value due to a stale TLB.
          */
-        flush_tlb_local();
+        flush_local(FLUSH_TLB | FLUSH_GUESTS_TLB);
     }
 }
 
@@ -4011,7 +4011,7 @@ sh_update_cr3(struct vcpu *v, int do_locking, bool noflush)
      * (old) shadow linear maps in the writeable mapping heuristics. */
 #if GUEST_PAGING_LEVELS == 2
     if ( sh_remove_write_access(d, gmfn, 2, 0) != 0 )
-        flush_tlb_mask(d->dirty_cpumask);
+        flush_mask(d->dirty_cpumask, FLUSH_TLB | FLUSH_GUESTS_TLB);
     sh_set_toplevel_shadow(v, 0, gmfn, SH_type_l2_shadow);
 #elif GUEST_PAGING_LEVELS == 3
     /* PAE guests have four shadow_table entries, based on the
@@ -4035,7 +4035,7 @@ sh_update_cr3(struct vcpu *v, int do_locking, bool noflush)
             }
         }
         if ( flush )
-            flush_tlb_mask(d->dirty_cpumask);
+            flush_mask(d->dirty_cpumask, FLUSH_TLB | FLUSH_GUESTS_TLB);
         /* Now install the new shadows. */
         for ( i = 0; i < 4; i++ )
         {
@@ -4056,7 +4056,7 @@ sh_update_cr3(struct vcpu *v, int do_locking, bool noflush)
     }
 #elif GUEST_PAGING_LEVELS == 4
     if ( sh_remove_write_access(d, gmfn, 4, 0) != 0 )
-        flush_tlb_mask(d->dirty_cpumask);
+        flush_mask(d->dirty_cpumask, FLUSH_TLB | FLUSH_GUESTS_TLB);
     sh_set_toplevel_shadow(v, 0, gmfn, SH_type_l4_shadow);
     if ( !shadow_mode_external(d) && !is_pv_32bit_domain(d) )
     {
@@ -4502,7 +4502,7 @@ static void sh_pagetable_dying(paddr_t gpa)
         }
     }
     if ( flush )
-        flush_tlb_mask(d->dirty_cpumask);
+        flush_mask(d->dirty_cpumask, FLUSH_TLB | FLUSH_GUESTS_TLB);
 
     /* Remember that we've seen the guest use this interface, so we
      * can rely on it using it in future, instead of guessing at
@@ -4539,7 +4539,7 @@ static void sh_pagetable_dying(paddr_t gpa)
         mfn_to_page(gmfn)->pagetable_dying = true;
         shadow_unhook_mappings(d, smfn, 1/* user pages only */);
         /* Now flush the TLB: we removed toplevel mappings. */
-        flush_tlb_mask(d->dirty_cpumask);
+        flush_mask(d->dirty_cpumask, FLUSH_TLB | FLUSH_GUESTS_TLB);
     }
 
     /* Remember that we've seen the guest use this interface, so we
xen/include/asm-x86/flushtlb.h +2 -0
index 2cfe4e6e97..07f9bc6103 100644
@@ -105,6 +105,8 @@ void switch_cr3_cr4(unsigned long cr3, unsigned long cr4);
 #define FLUSH_VCPU_STATE 0x1000
  /* Flush the per-cpu root page table */
 #define FLUSH_ROOT_PGTBL 0x2000
+ /* Flush all HVM guests linear TLB (using ASID/VPID) */
+#define FLUSH_GUESTS_TLB 0x4000
 
 /* Flush local TLBs/caches. */
 unsigned int flush_area_local(const void *va, unsigned int flags);
Signature · 7 lines
2.25.0


_______________________________________________
Xen-devel mailing list
[email protected]
https://lists.xenproject.org/mailman/listinfo/xen-devel
Acked-by on v4 4/7
#7 lore raw

Re: [Xen-devel] [PATCH v4 4/7] x86/tlb: introduce a flush guests TLB flag

Quoted 8 lines · Roger Pau Monne

Introduce a specific flag to request a HVM guest TLB flush, which is an ASID/VPID tickle that forces a linear TLB flush for all HVM guests.

This was previously unconditionally done in each pre_flush call, but that's not required: HVM guests not using shadow don't require linear TLB flushes as Xen doesn't modify the guest page tables in that case (ie: when using HAP).

Quoted 8 lines

Modify all shadow code TLB flushes to also flush the guest TLB, in order to keep the previous behavior. I haven't looked at each specific shadow code TLB flush in order to figure out whether it actually requires a guest TLB flush or not, so there might be room for improvement in that regard.

_______________________________________________
Xen-devel mailing list
[email protected]
https://lists.xenproject.org/mailman/listinfo/xen-devel

#8 lore raw

PATCH v4 5/7 x86/tlb: allow disabling the TLB clock

In reply to Roger Pau Monne

The TLB clock is helpful when running Xen on bare metal because when doing a TLB flush each CPU is IPI'ed and can keep a timestamp of the last flush.

This is not the case however when Xen is running virtualized, and the underlying hypervisor provides mechanism to assist in performing TLB
flushes: Xen itself for example offers a HVMOP_flush_tlbs hypercall in order to perform a TLB flush without having to IPI each CPU. When using such mechanisms it's no longer possible to keep a timestamp of the flushes on each CPU, as they are performed by the underlying hypervisor.

Offer a boolean in order to signal Xen that the timestamped TLB shouldn't be used. This avoids keeping the timestamps of the flushes, and also forces NEED_FLUSH to always return true.

No functional change intended, as this change doesn't introduce any user that disables the timestamped TLB.

---
 xen/arch/x86/flushtlb.c        | 19 +++++++++++++------
 xen/include/asm-x86/flushtlb.h | 17 ++++++++++++++++-
 2 files changed, 29 insertions(+), 7 deletions(-)
xen/arch/x86/flushtlb.c +13 -6
index e7ccd4ec7b..3649900793 100644
@@ -32,6 +32,9 @@
 u32 tlbflush_clock = 1U;
 DEFINE_PER_CPU(u32, tlbflush_time);
 
+/* Signals whether the TLB flush clock is in use. */
+bool __read_mostly tlb_clk_enabled = true;
+
 /*
  * pre_flush(): Increment the virtual TLB-flush clock. Returns new clock value.
  * 
@@ -82,12 +85,13 @@ static void post_flush(u32 t)
 static void do_tlb_flush(void)
 {
     unsigned long flags, cr4;
-    u32 t;
+    u32 t = 0;
 
     /* This non-reentrant function is sometimes called in interrupt context. */
     local_irq_save(flags);
 
-    t = pre_flush();
+    if ( tlb_clk_enabled )
+        t = pre_flush();
 
     if ( use_invpcid )
         invpcid_flush_all();
@@ -99,7 +103,8 @@ static void do_tlb_flush(void)
     else
         write_cr3(read_cr3());
 
-    post_flush(t);
+    if ( tlb_clk_enabled )
+        post_flush(t);
 
     local_irq_restore(flags);
 }
@@ -107,7 +112,7 @@ static void do_tlb_flush(void)
 void switch_cr3_cr4(unsigned long cr3, unsigned long cr4)
 {
     unsigned long flags, old_cr4;
-    u32 t;
+    u32 t = 0;
 
     /* Throughout this function we make this assumption: */
     ASSERT(!(cr4 & X86_CR4_PCIDE) || !(cr4 & X86_CR4_PGE));
@@ -115,7 +120,8 @@ void switch_cr3_cr4(unsigned long cr3, unsigned long cr4)
     /* This non-reentrant function is sometimes called in interrupt context. */
     local_irq_save(flags);
 
-    t = pre_flush();
+    if ( tlb_clk_enabled )
+        t = pre_flush();
 
     old_cr4 = read_cr4();
     ASSERT(!(old_cr4 & X86_CR4_PCIDE) || !(old_cr4 & X86_CR4_PGE));
@@ -167,7 +173,8 @@ void switch_cr3_cr4(unsigned long cr3, unsigned long cr4)
     if ( cr4 & X86_CR4_PCIDE )
         invpcid_flush_all_nonglobals();
 
-    post_flush(t);
+    if ( tlb_clk_enabled )
+        post_flush(t);
 
     local_irq_restore(flags);
 }
xen/include/asm-x86/flushtlb.h +16 -1
index 07f9bc6103..9773014320 100644
@@ -21,10 +21,21 @@ extern u32 tlbflush_clock;
 /* Time at which each CPU's TLB was last flushed. */
 DECLARE_PER_CPU(u32, tlbflush_time);
 
-#define tlbflush_current_time() tlbflush_clock
+/* TLB clock is in use. */
+extern bool tlb_clk_enabled;
+
+static inline uint32_t tlbflush_current_time(void)
+{
+    /* Returning 0 from tlbflush_current_time will always force a flush. */
+    return tlb_clk_enabled ? tlbflush_clock : 0;
+}
 
 static inline void page_set_tlbflush_timestamp(struct page_info *page)
 {
+    /* Avoid the write if the TLB clock is disabled. */
+    if ( !tlb_clk_enabled )
+        return;
+
     /*
      * Prevent storing a stale time stamp, which could happen if an update
      * to tlbflush_clock plus a subsequent flush IPI happen between the
@@ -67,6 +78,10 @@ static inline void tlbflush_filter(cpumask_t *mask, uint32_t page_timestamp)
 {
     unsigned int cpu;
 
+    /* Short-circuit: there's no need to iterate if the clock is disabled. */
+    if ( !tlb_clk_enabled )
+        return;
+
     for_each_cpu ( cpu, mask )
         if ( !NEED_FLUSH(per_cpu(tlbflush_time, cpu), page_timestamp) )
             __cpumask_clear_cpu(cpu, mask);
Signature · 7 lines
2.25.0


_______________________________________________
Xen-devel mailing list
[email protected]
https://lists.xenproject.org/mailman/listinfo/xen-devel
Reviewed-by on v4 5/7
#9 lore raw

Re: [Xen-devel] [PATCH v4 5/7] x86/tlb: allow disabling the TLB clock

Quoted 12 lines · Roger Pau Monne

The TLB clock is helpful when running Xen on bare metal because when doing a TLB flush each CPU is IPI'ed and can keep a timestamp of the last flush.

This is not the case however when Xen is running virtualized, and the underlying hypervisor provides mechanism to assist in performing TLB
flushes: Xen itself for example offers a HVMOP_flush_tlbs hypercall in order to perform a TLB flush without having to IPI each CPU. When using such mechanisms it's no longer possible to keep a timestamp of the flushes on each CPU, as they are performed by the underlying hypervisor.

Quoted 8 lines

Offer a boolean in order to signal Xen that the timestamped TLB shouldn't be used. This avoids keeping the timestamps of the flushes, and also forces NEED_FLUSH to always return true.

No functional change intended, as this change doesn't introduce any user that disables the timestamped TLB.

_______________________________________________
Xen-devel mailing list
[email protected]
https://lists.xenproject.org/mailman/listinfo/xen-devel

#10 lore raw

PATCH v4 6/7 xen/guest: prepare hypervisor ops to use alternative calls

In reply to Roger Pau Monne

Adapt the hypervisor ops framework so it can be used with the alternative calls framework. So far no hooks are modified to make use of the alternatives patching, as they are not in any hot path.

No functional change intended.

---
Changes since v3:
- New in this version.

---
 xen/arch/x86/guest/hyperv/hyperv.c |  2 +-
 xen/arch/x86/guest/hypervisor.c    | 41 +++++++++++++++---------------
 xen/arch/x86/guest/xen/xen.c       |  2 +-
 3 files changed, 23 insertions(+), 22 deletions(-)
xen/arch/x86/guest/hyperv/hyperv.c +1 -1
index fabc62b0d6..70f4cd5ae0 100644
@@ -199,7 +199,7 @@ static void __init e820_fixup(struct e820map *e820)
         panic("Unable to reserve Hyper-V hypercall range\n");
 }
 
-static const struct hypervisor_ops ops = {
+static const struct hypervisor_ops __initdata ops = {
     .name = "Hyper-V",
     .setup = setup,
     .ap_setup = ap_setup,
xen/arch/x86/guest/hypervisor.c +21 -20

73 lines not on this page · raw message

xen/arch/x86/guest/xen/xen.c +1 -1
index 3cf8f667a1..f151b07548 100644
@@ -324,7 +324,7 @@ static void __init e820_fixup(struct e820map *e820)
         pv_shim_fixup_e820(e820);
 }
 
-static const struct hypervisor_ops ops = {
+static const struct hypervisor_ops __initdata ops = {
     .name = "Xen",
     .setup = setup,
     .ap_setup = ap_setup,
Signature · 7 lines
2.25.0


_______________________________________________
Xen-devel mailing list
[email protected]
https://lists.xenproject.org/mailman/listinfo/xen-devel
Reviewed-by on v4 6/7
#11 lore raw

Re: [Xen-devel] [PATCH v4 6/7] xen/guest: prepare hypervisor ops to use alternative calls

Quoted 7 lines · Roger Pau Monne

Adapt the hypervisor ops framework so it can be used with the alternative calls framework. So far no hooks are modified to make use of the alternatives patching, as they are not in any hot path.

No functional change intended.

_______________________________________________
Xen-devel mailing list
[email protected]
https://lists.xenproject.org/mailman/listinfo/xen-devel

Reviewed-by Paul Durrant on v4 6/7
#12 lore raw

Re: [Xen-devel] [PATCH v4 6/7] xen/guest: prepare hypervisor ops to use alternative calls

In reply to Roger Pau Monne
Quoted 10 lines

-----Original Message-----
From: Roger Pau Monne <[email protected]>
Sent: 10 February 2020 18:28
To: [email protected]
Cc: Roger Pau Monne <[email protected]>; Durrant, Paul <[email protected]>; Wei Liu <[email protected]>; Jan Beulich <[email protected]>; Andrew Cooper <[email protected]>
Subject: [PATCH v4 6/7] xen/guest: prepare hypervisor ops to use alternative calls

Quoted 7 lines

Adapt the hypervisor ops framework so it can be used with the alternative calls framework. So far no hooks are modified to make use of the alternatives patching, as they are not in any hot path.

No functional change intended.

_______________________________________________
Xen-devel mailing list
[email protected]
https://lists.xenproject.org/mailman/listinfo/xen-devel

#13 lore raw

PATCH v4 7/7 x86/tlb: use Xen L0 assisted TLB flush when available

In reply to Roger Pau Monne

Use Xen's L0 HVMOP_flush_tlbs hypercall in order to perform flushes. This greatly increases the performance of TLB flushes when running with a high amount of vCPUs as a Xen guest, and is specially important when running in shim mode.

The following figures are from a PV guest running make -j32 xen in shim mode with 32 vCPUs and HAP.

Using x2APIC and ALLBUT shorthand:
real 4m35.973s
user 4m35.110s
sys 36m24.117s

Using L0 assisted flush:

real    1m2.596s
user    4m34.818s
sys     5m16.374s

The implementation adds a new hook to hypervisor_ops so other enlightenments can also implement such assisted flush just by filling the hook. Note that the Xen implementation completely ignores the dirty CPU mask and the linear address passed in, and always performs a global TLB flush on all vCPUs.

---
Changes since v3:
- Use an alternative call for the flush hook.

Changes since v1:
- Add a L0 assisted hook to hypervisor ops.

---
 xen/arch/x86/guest/hypervisor.c        | 10 ++++++++++
 xen/arch/x86/guest/xen/xen.c           |  6 ++++++
 xen/arch/x86/smp.c                     | 11 +++++++++++
 xen/include/asm-x86/guest/hypervisor.h | 17 +++++++++++++++++
 4 files changed, 44 insertions(+)
xen/arch/x86/guest/hypervisor.c +10 -0
index 647cdb1367..47e938e287 100644
@@ -18,6 +18,7 @@
  *
  * Copyright (c) 2019 Microsoft.
  */
+#include <xen/cpumask.h>
 #include <xen/init.h>
 #include <xen/types.h>
 
@@ -73,6 +74,15 @@ void __init hypervisor_e820_fixup(struct e820map *e820)
         ops.e820_fixup(e820);
 }
 
+int hypervisor_flush_tlb(const cpumask_t *mask, const void *va,
+                         unsigned int order)
+{
+    if ( ops.flush_tlb )
+        return alternative_call(ops.flush_tlb, mask, va, order);
+
+    return -ENOSYS;
+}
+
 /*
  * Local variables:
  * mode: C
xen/arch/x86/guest/xen/xen.c +6 -0
index f151b07548..5d3427a713 100644
@@ -324,12 +324,18 @@ static void __init e820_fixup(struct e820map *e820)
         pv_shim_fixup_e820(e820);
 }
 
+static int flush_tlb(const cpumask_t *mask, const void *va, unsigned int order)
+{
+    return xen_hypercall_hvm_op(HVMOP_flush_tlbs, NULL);
+}
+
 static const struct hypervisor_ops __initdata ops = {
     .name = "Xen",
     .setup = setup,
     .ap_setup = ap_setup,
     .resume = resume,
     .e820_fixup = e820_fixup,
+    .flush_tlb = flush_tlb,
 };
 
 const struct hypervisor_ops *__init xg_probe(void)
xen/arch/x86/smp.c +11 -0
index 65eb7cbda8..9bc925616a 100644
@@ -15,6 +15,7 @@
 #include <xen/perfc.h>
 #include <xen/spinlock.h>
 #include <asm/current.h>
+#include <asm/guest.h>
 #include <asm/smp.h>
 #include <asm/mc146818rtc.h>
 #include <asm/flushtlb.h>
@@ -256,6 +257,16 @@ void flush_area_mask(const cpumask_t *mask, const void *va, unsigned int flags)
     if ( (flags & ~FLUSH_ORDER_MASK) &&
          !cpumask_subset(mask, cpumask_of(cpu)) )
     {
+        if ( cpu_has_hypervisor &&
+             !(flags & ~(FLUSH_TLB | FLUSH_TLB_GLOBAL | FLUSH_VA_VALID |
+                         FLUSH_ORDER_MASK)) &&
+             !hypervisor_flush_tlb(mask, va, flags & FLUSH_ORDER_MASK) )
+        {
+            if ( tlb_clk_enabled )
+                tlb_clk_enabled = false;
+            return;
+        }
+
         spin_lock(&flush_lock);
         cpumask_and(&flush_cpumask, mask, &cpu_online_map);
         cpumask_clear_cpu(cpu, &flush_cpumask);
xen/include/asm-x86/guest/hypervisor.h +17 -0
index ade10e74ea..432e57c2a0 100644
@@ -19,6 +19,8 @@
 #ifndef __X86_HYPERVISOR_H__
 #define __X86_HYPERVISOR_H__
 
+#include <xen/cpumask.h>
+
 #include <asm/e820.h>
 
 struct hypervisor_ops {
@@ -32,6 +34,8 @@ struct hypervisor_ops {
     void (*resume)(void);
     /* Fix up e820 map */
     void (*e820_fixup)(struct e820map *e820);
+    /* L0 assisted TLB flush */
+    int (*flush_tlb)(const cpumask_t *mask, const void *va, unsigned int order);
 };
 
 #ifdef CONFIG_GUEST
@@ -41,6 +45,14 @@ void hypervisor_setup(void);
 int hypervisor_ap_setup(void);
 void hypervisor_resume(void);
 void hypervisor_e820_fixup(struct e820map *e820);
+/*
+ * L0 assisted TLB flush.
+ * mask: cpumask of the dirty vCPUs that should be flushed.
+ * va: linear address to flush, or NULL for global flushes.
+ * order: order of the linear address pointed by va.
+ */
+int hypervisor_flush_tlb(const cpumask_t *mask, const void *va,
+                         unsigned int order);
 
 #else
 
@@ -52,6 +64,11 @@ static inline void hypervisor_setup(void) { ASSERT_UNREACHABLE(); }
 static inline int hypervisor_ap_setup(void) { return 0; }
 static inline void hypervisor_resume(void) { ASSERT_UNREACHABLE(); }
 static inline void hypervisor_e820_fixup(struct e820map *e820) {}
+static inline int hypervisor_flush_tlb(const cpumask_t *mask, const void *va,
+                                       unsigned int order)
+{
+    return -ENOSYS;
+}
 
 #endif  /* CONFIG_GUEST */
 
Signature · 7 lines
2.25.0


_______________________________________________
Xen-devel mailing list
[email protected]
https://lists.xenproject.org/mailman/listinfo/xen-devel
Reviewed-by on v4 7/7
#14 lore raw

Re: [Xen-devel] [PATCH v4 7/7] x86/tlb: use Xen L0 assisted TLB flush when available

Quoted 18 lines · Roger Pau Monne

Use Xen's L0 HVMOP_flush_tlbs hypercall in order to perform flushes. This greatly increases the performance of TLB flushes when running with a high amount of vCPUs as a Xen guest, and is specially important when running in shim mode.

The following figures are from a PV guest running make -j32 xen in shim mode with 32 vCPUs and HAP.

Using x2APIC and ALLBUT shorthand:
real 4m35.973s
user 4m35.110s
sys 36m24.117s

Using L0 assisted flush:

real    1m2.596s
user    4m34.818s
sys     5m16.374s
Quoted 7 lines

The implementation adds a new hook to hypervisor_ops so other enlightenments can also implement such assisted flush just by filling the hook. Note that the Xen implementation completely ignores the dirty CPU mask and the linear address passed in, and always performs a global TLB flush on all vCPUs.

One remark below.

[...]

Quoted 14 lines

const struct hypervisor_ops *__init xg_probe(void)

xen/arch/x86/smp.c +1 -0
index 65eb7cbda8..9bc925616a 100644
@@ -15,6 +15,7 @@
 #include <xen/perfc.h>
 #include <xen/spinlock.h>
 #include <asm/current.h>
+#include <asm/guest.h>
 #include <asm/smp.h>
 #include <asm/mc146818rtc.h>
 #include <asm/flushtlb.h>

xen/arch/x86/smp.c void flush_area_mask(const cpumask_t *mask, const void *va, unsigned int flags) · line 263

Quoted 7 lines
xen/arch/x86/smp.c +4 -0
@@ -256,6 +257,16 @@ void flush_area_mask(const cpumask_t *mask, const void *va, unsigned int flags)
     if ( (flags & ~FLUSH_ORDER_MASK) &&
          !cpumask_subset(mask, cpumask_of(cpu)) )
     {
+        if ( cpu_has_hypervisor &&
+             !(flags & ~(FLUSH_TLB | FLUSH_TLB_GLOBAL | FLUSH_VA_VALID |
+                         FLUSH_ORDER_MASK)) &&
+             !hypervisor_flush_tlb(mask, va, flags & FLUSH_ORDER_MASK) )

I would like pass in the flag as a whole because Hyper-V has the capability to fine tune what gets flushed. I can see FLUSH_TLB_GLOBAL being used in that situation.

There is no need to change your patch though. I can submit a patch myself to change this interface once your series is accepted.

_______________________________________________
Xen-devel mailing list
[email protected]
https://lists.xenproject.org/mailman/listinfo/xen-devel

#15 lore raw

Re: [Xen-devel] [PATCH v4 7/7] x86/tlb: use Xen L0 assisted TLB flush when available

In reply to Roger Pau Monne

On Mon, Feb 10, 2020 at 06:28:29PM +0100, Roger Pau Monne wrote:
[...]

Quoted 12 lines

struct hypervisor_ops {

xen/include/asm-x86/guest/hypervisor.h +2 -0
@@ -32,6 +34,8 @@ struct hypervisor_ops {
     void (*resume)(void);
     /* Fix up e820 map */
     void (*e820_fixup)(struct e820map *e820);
+    /* L0 assisted TLB flush */
+    int (*flush_tlb)(const cpumask_t *mask, const void *va, unsigned int order);
 };
 
 #ifdef CONFIG_GUEST

xen/include/asm-x86/guest/hypervisor.h void hypervisor_setup(void); · line 51

Quoted 7 lines
xen/include/asm-x86/guest/hypervisor.h +4 -0
@@ -41,6 +45,14 @@ void hypervisor_setup(void);
 int hypervisor_ap_setup(void);
 void hypervisor_resume(void);
 void hypervisor_e820_fixup(struct e820map *e820);
+/*
+ * L0 assisted TLB flush.
+ * mask: cpumask of the dirty vCPUs that should be flushed.
+ * va: linear address to flush, or NULL for global flushes.

I was in the middle of writing my patch and noticed this.

I think NULL means "flushing the entire address space" here?

Wei.

_______________________________________________
Xen-devel mailing list
[email protected]
https://lists.xenproject.org/mailman/listinfo/xen-devel

#16 lore raw

Re: [Xen-devel] [PATCH v4 7/7] x86/tlb: use Xen L0 assisted TLB flush when available

Quoted 24 lines · Wei Liu

On Mon, Feb 10, 2020 at 06:28:29PM +0100, Roger Pau Monne wrote:
[...]

Quoted 12 lines

struct hypervisor_ops {

xen/include/asm-x86/guest/hypervisor.h +2 -0
@@ -32,6 +34,8 @@ struct hypervisor_ops {
     void (*resume)(void);
     /* Fix up e820 map */
     void (*e820_fixup)(struct e820map *e820);
+    /* L0 assisted TLB flush */
+    int (*flush_tlb)(const cpumask_t *mask, const void *va, unsigned int order);
 };
 
 #ifdef CONFIG_GUEST

xen/include/asm-x86/guest/hypervisor.h void hypervisor_setup(void); · line 51

Quoted 7 lines
xen/include/asm-x86/guest/hypervisor.h +4 -0
@@ -41,6 +45,14 @@ void hypervisor_setup(void);
 int hypervisor_ap_setup(void);
 void hypervisor_resume(void);
 void hypervisor_e820_fixup(struct e820map *e820);
+/*
+ * L0 assisted TLB flush.
+ * mask: cpumask of the dirty vCPUs that should be flushed.
+ * va: linear address to flush, or NULL for global flushes.

I was in the middle of writing my patch and noticed this.

Quoted 1 line

I think NULL means "flushing the entire address space" here?

Yes, that's right. I didn't add a way to differentiate between global (ie: PGE mappings included) flushes and non-global flushes, so all calls are assumed to imply flushes of global mappings.

It might be better if you adapt it yourself to whatever is more suited for HyperV which has more selective flushes available. Xen only has an hypercall to request a global flush on all vCPUs.

Thanks, Roger.

_______________________________________________
Xen-devel mailing list
[email protected]
https://lists.xenproject.org/mailman/listinfo/xen-devel

#17 lore raw

Re: [Xen-devel] [PATCH v4 7/7] x86/tlb: use Xen L0 assisted TLB flush when available

Quoted 27 lines · Roger Pau Monné
Quoted 24 lines · Wei Liu

On Mon, Feb 10, 2020 at 06:28:29PM +0100, Roger Pau Monne wrote:
[...]

Quoted 12 lines

struct hypervisor_ops {

xen/include/asm-x86/guest/hypervisor.h +2 -0
@@ -32,6 +34,8 @@ struct hypervisor_ops {
     void (*resume)(void);
     /* Fix up e820 map */
     void (*e820_fixup)(struct e820map *e820);
+    /* L0 assisted TLB flush */
+    int (*flush_tlb)(const cpumask_t *mask, const void *va, unsigned int order);
 };
 
 #ifdef CONFIG_GUEST

xen/include/asm-x86/guest/hypervisor.h void hypervisor_setup(void); · line 51

Quoted 7 lines
xen/include/asm-x86/guest/hypervisor.h +4 -0
@@ -41,6 +45,14 @@ void hypervisor_setup(void);
 int hypervisor_ap_setup(void);
 void hypervisor_resume(void);
 void hypervisor_e820_fixup(struct e820map *e820);
+/*
+ * L0 assisted TLB flush.
+ * mask: cpumask of the dirty vCPUs that should be flushed.
+ * va: linear address to flush, or NULL for global flushes.

I was in the middle of writing my patch and noticed this.

Quoted 1 line

I think NULL means "flushing the entire address space" here?

Quoted 7 lines

Yes, that's right. I didn't add a way to differentiate between global (ie: PGE mappings included) flushes and non-global flushes, so all calls are assumed to imply flushes of global mappings.

It might be better if you adapt it yourself to whatever is more suited for HyperV which has more selective flushes available. Xen only has an hypercall to request a global flush on all vCPUs.

OK. Thanks for confirming.

I will change this comment in my patch.

Wei.

Quoted 2 lines

Thanks, Roger.

_______________________________________________
Xen-devel mailing list
[email protected]
https://lists.xenproject.org/mailman/listinfo/xen-devel

#18 lore raw

Re: [Xen-devel] [PATCH v4 7/7] x86/tlb: use Xen L0 assisted TLB flush when available

In reply to Roger Pau Monne

xen/arch/x86/smp.c void flush_area_mask(const cpumask_t *mask, const void *va, unsigned int flags) · line 263

Quoted 8 lines · Roger Pau Monne
xen/arch/x86/smp.c +4 -0
@@ -256,6 +257,16 @@ void flush_area_mask(const cpumask_t *mask, const void *va, unsigned int flags)
     if ( (flags & ~FLUSH_ORDER_MASK) &&
          !cpumask_subset(mask, cpumask_of(cpu)) )
     {
+        if ( cpu_has_hypervisor &&
+             !(flags & ~(FLUSH_TLB | FLUSH_TLB_GLOBAL | FLUSH_VA_VALID |
+                         FLUSH_ORDER_MASK)) &&
+             !hypervisor_flush_tlb(mask, va, flags & FLUSH_ORDER_MASK) )

This needs to be adjusted to (flags - 1) & FLUSH_ORDER_MASK.

_______________________________________________
Xen-devel mailing list
[email protected]
https://lists.xenproject.org/mailman/listinfo/xen-devel