KVM: x86: honor guest memory type
Subsystems (4)
cover KVM: x86: honor guest memory type
Hi,
Host GPU drivers like to give userspace WC mapping. When the userspace makes the mapping available to a guest, it also tells the guest to create a WC mapping. However, even when the guest kernel picks the correct memory type, it gets ignored because of VMX_EPT_IPAT_BIT on Intel.
This series adds a new flag to KVM_SET_USER_MEMORY_REGION, which tells the host kernel to honor the guest memory type for the memslot. An alternative fix is for KVM to unconditionally honor the guest memory type (unless it is MMIO, to avoid MCEs on Intel). I believe the alternative fix is how things are on ARM, and probably also how things are on AMD.
I am new to KVM and HW virtualization technologies. This series is meant as an RFC.
_______________________________________________
dri-devel mailing list
[email protected]
https://lists.freedesktop.org/mailman/listinfo/dri-devel
RFC PATCH 1/3 KVM: vmx: rewrite the comment in vmx_get_mt_mask
Better reflect the structure of the code and metion why we could not always honor the guest.
--- arch/x86/kvm/vmx/vmx.c | 27 +++++++++++++++++---------- 1 file changed, 17 insertions(+), 10 deletions(-)
arch/x86/kvm/vmx/vmx.c +17 -10
@@ -6854,17 +6854,24 @@ static u64 vmx_get_mt_mask(struct kvm_vcpu *vcpu, gfn_t gfn, bool is_mmio)u8 cache;u64 ipat =0 ; -/* For VT-d and EPT combination -* 1. MMIO: always map as UC -* 2. EPT with VT-d: -* a. VT-d without snooping control feature: can't guarantee the -* result, try to trust guest. -* b. VT-d with snooping control feature: snooping control feature of -* VT-d engine can guarantee the cache correctness. Just set it -* to WB to keep consistent with host. So the same as item 3. -* 3. EPT without VT-d: always map as WB and set IPAT=1 to keep -* consistent with host MTRR +/* We wanted to honor guest CD/MTRR/PAT, but doing so could result in +* memory aliases with conflicting memory types and sometimes MCEs. +* We have to be careful as to what are honored and when. +* +* For MMIO, guest CD/MTRR are ignored. The EPT memory type is set to +* UC. The effective memory type is UC or WC depending on guest PAT. +* This was historically the source of MCEs and we want to be +* conservative. +* +* When there is no need to deal with noncoherent DMA (e.g., no VT-d +* or VT-d has snoop control), guest CD/MTRR/PAT are all ignored. The +* EPT memory type is set to WB. The effective memory type is forced +* WB. +* +* Otherwise, we trust guest. Guest CD/MTRR/PAT are all honored. The +* EPT memory type is used to emulate guest CD/MTRR. */ +if (is_mmio) { cache =MTRR_TYPE_UNCACHABLE ; goto exit;
Signature · 6 lines
2.25.0.265.gbab2e86ba0-goog _______________________________________________ dri-devel mailing list [email protected] https://lists.freedesktop.org/mailman/listinfo/dri-devel
Paolo Bonzini
maintainerRe: [RFC PATCH 1/3] KVM: vmx: rewrite the comment in vmx_get_mt_mask
Quoted 40 lines · Chia-I Wu
Better reflect the structure of the code and metion why we could not always honor the guest.
Signed-off-by Chia-I Wu <[email protected]>Cc Gurchetan Singh <[email protected]>Cc Gerd Hoffmann <[email protected]>--- arch/x86/kvm/vmx/vmx.c | 27 +++++++++++++++++---------- 1 file changed, 17 insertions(+), 10 deletions(-)arch/x86/kvm/vmx/vmx.c +11
-10@@ -6854,17 +6854,24 @@ static u64 vmx_get_mt_mask(struct kvm_vcpu *vcpu, gfn_t gfn, bool is_mmio)u8 cache;u64 ipat =0 ; -/* For VT-d and EPT combination -* 1. MMIO: always map as UC -* 2. EPT with VT-d: -* a. VT-d without snooping control feature: can't guarantee the -* result, try to trust guest. -* b. VT-d with snooping control feature: snooping control feature of -* VT-d engine can guarantee the cache correctness. Just set it -* to WB to keep consistent with host. So the same as item 3. -* 3. EPT without VT-d: always map as WB and set IPAT=1 to keep -* consistent with host MTRR +/* We wanted to honor guest CD/MTRR/PAT, but doing so could result in +* memory aliases with conflicting memory types and sometimes MCEs. +* We have to be careful as to what are honored and when. +* +* For MMIO, guest CD/MTRR are ignored. The EPT memory type is set to +* UC. The effective memory type is UC or WC depending on guest PAT. +* This was historically the source of MCEs and we want to be +* conservative. +* +* When there is no need to deal with noncoherent DMA (e.g., no VT-d +* or VT-d has snoop control), guest CD/MTRR/PAT are all ignored. The
arch/x86/kvm/vmx/vmx.c static u64 vmx_get_mt_mask(struct kvm_vcpu *vcpu, gfn_t gfn, bool is_mmio) · line 6877
Quoted 10 lines
arch/x86/kvm/vmx/vmx.c +6
-0+* EPT memory type is set to WB. The effective memory type is forced +* WB. +* +* Otherwise, we trust guest. Guest CD/MTRR/PAT are all honored. The +* EPT memory type is used to emulate guest CD/MTRR. */ +if (is_mmio) { cache =MTRR_TYPE_UNCACHABLE ; goto exit;
This is certainly an improvement, especially the part that points out how guest PAT still allows MMIO to be handled as WC.
Thanks,
Paolo
RFC PATCH 2/3 RFC: KVM: add KVM_MEM_DMA
In reply to Chia-I WuWhen the flag is set, it means the the userspace wants to do DMA with the memory and the guest will use an appropriate memory type to access the memory. The kernel should be prepared to honor the guest's memory type.
--- Documentation/virt/kvm/api.rst | 17 +++++++++++------ include/uapi/linux/kvm.h | 2 ++ virt/kvm/kvm_main.c | 6 +++++- 3 files changed, 18 insertions(+), 7 deletions(-)
Documentation/virt/kvm/api.rst +11 -6
@@ -1237,6 +1237,7 @@ yet and must be cleared on entry. /* for kvm_memory_region::flags */ #define KVM_MEM_LOG_DIRTY_PAGES (1UL << 0) #define KVM_MEM_READONLY (1UL << 1) + #define KVM_MEM_DMA (1UL << 2) This ioctl allows the user to create, modify or delete a guest physical memory slot. Bits 0-15 of "slot" specify the slot id and this value
@@ -1264,12 +1265,16 @@ It is recommended that the lower 21 bits of guest_phys_addr and userspace_addr be identical. This allows large pages in the guest to be backed by large pages in the host. -The flags field supports two flags: KVM_MEM_LOG_DIRTY_PAGES and -KVM_MEM_READONLY. The former can be set to instruct KVM to keep track of -writes to memory within the slot. See KVM_GET_DIRTY_LOG ioctl to know how to -use it. The latter can be set, if KVM_CAP_READONLY_MEM capability allows it, -to make a new slot read-only. In this case, writes to this memory will be -posted to userspace as KVM_EXIT_MMIO exits. +The flags field supports these flags: KVM_MEM_LOG_DIRTY_PAGES, +KVM_MEM_READONLY, and KVM_MEM_DMA. KVM_MEM_LOG_DIRTY_PAGES can be set to +instruct KVM to keep track of writes to memory within the slot. See +KVM_GET_DIRTY_LOG ioctl to know how to use it. KVM_MEM_READONLY can be set, +if KVM_CAP_READONLY_MEM capability allows it, to make a new slot read-only. +In this case, writes to this memory will be posted to userspace as +KVM_EXIT_MMIO exits. KVM_MEM_DMA can be set, if KVM_CAP_DMA_MEM capability +allows it, to make a new slot support DMA. It is the userspace's +responsibility to make sure userspace_addr points at a DMA-able memory and the +guest's responsibility to map guest_phys_addr with the proper memory type. When the KVM_CAP_SYNC_MMU capability is available, changes in the backing of the memory region are automatically reflected into the guest. For example, an
include/uapi/linux/kvm.h +2 -0
@@ -109,6 +109,7 @@ struct kvm_userspace_memory_region {*/ #define KVM_MEM_LOG_DIRTY_PAGES (1UL << 0)#define KVM_MEM_READONLY (1UL << 1) +#define KVM_MEM_DMA (1UL << 2)/* for KVM_IRQ_LINE */ struct kvm_irq_level {
@@ -1010,6 +1011,7 @@ struct kvm_ppc_resize_hpt {#define KVM_CAP_ARM_NISV_TO_USER 177#define KVM_CAP_ARM_INJECT_EXT_DABT 178#define KVM_CAP_S390_VCPU_RESETS 179 +#define KVM_CAP_DMA_MEM 180#ifdef KVM_CAP_IRQ_ROUTING
virt/kvm/kvm_main.c +5 -1
@@ -940,6 +940,9 @@ static int check_memory_region_flags(const struct kvm_userspace_memory_region *m#ifdef __KVM_HAVE_READONLY_MEM valid_flags |=KVM_MEM_READONLY ;#endif +#ifdef __KVM_HAVE_DMA_MEM + valid_flags |=KVM_MEM_DMA ; +#endif if (mem->flags & ~valid_flags)return -EINVAL ;
@@ -1047,7 +1050,8 @@ int __kvm_set_memory_region(struct kvm *kvm,else {/* Modify an existing slot. */ if ((mem->userspace_addr != old.userspace_addr) || (npages != old.npages) || - ((new.flags ^ old.flags) &KVM_MEM_READONLY )) + ((new.flags ^ old.flags) & + (KVM_MEM_READONLY |KVM_MEM_DMA ))) goto out;if (base_gfn != old.base_gfn)
Signature · 6 lines
2.25.0.265.gbab2e86ba0-goog _______________________________________________ dri-devel mailing list [email protected] https://lists.freedesktop.org/mailman/listinfo/dri-devel
RFC PATCH 3/3 RFC: KVM: x86: support KVM_CAP_DMA_MEM
In reply to Chia-I WuWhen a memslot has KVM_MEM_DMA set, we want VMX_EPT_IPAT_BIT cleared for the memslot. Before that is possible, simply call kvm_arch_register_noncoherent_dma for the memslot.
SVM does not have the ignore-pat bit. Guest PAT is always honored.
--- arch/x86/include/uapi/asm/kvm.h | 1 + arch/x86/kvm/x86.c | 6 ++++++ 2 files changed, 7 insertions(+)
arch/x86/include/uapi/asm/kvm.h +1 -0
@@ -48,6 +48,7 @@#define __KVM_HAVE_XSAVE#define __KVM_HAVE_XCRS#define __KVM_HAVE_READONLY_MEM +#define __KVM_HAVE_DMA_MEM/* Architectural interrupt line count. */ #define KVM_NR_INTERRUPTS 256
arch/x86/kvm/x86.c +6 -0
@@ -3331,6 +3331,7 @@ int kvm_vm_ioctl_check_extension(struct kvm *kvm, long ext)case KVM_CAP_GET_TSC_KHZ :case KVM_CAP_KVMCLOCK_CTRL :case KVM_CAP_READONLY_MEM : +case KVM_CAP_DMA_MEM :case KVM_CAP_HYPERV_TIME :case KVM_CAP_IOAPIC_POLARITY_IGNORED :case KVM_CAP_TSC_DEADLINE_TIMER :
@@ -10045,6 +10046,11 @@ void kvm_arch_commit_memory_region(struct kvm *kvm,*/ if (change !=KVM_MR_DELETE )kvm_mmu_slot_apply_flags (kvm, (struct kvm_memory_slot *) new); + +if (change ==KVM_MR_CREATE && new->flags &KVM_MEM_DMA ) +kvm_arch_register_noncoherent_dma (kvm); +else if (change ==KVM_MR_DELETE && old->flags &KVM_MEM_DMA ) +kvm_arch_unregister_noncoherent_dma (kvm); }void kvm_arch_flush_shadow_all (struct kvm *kvm)
Signature · 1 line
2.25.0.265.gbab2e86ba0-goog
Paolo Bonzini
maintainerQuoted 7 lines · Chia-I Wu
Hi,
Host GPU drivers like to give userspace WC mapping. When the userspace makes the mapping available to a guest, it also tells the guest to create a WC mapping. However, even when the guest kernel picks the correct memory type, it gets ignored because of
VMX_EPT_IPAT_BITon Intel.
Quoted 9 lines
This series adds a new flag to
KVM_SET_USER_MEMORY_REGION, which tells the host kernel to honor the guest memory type for the memslot. An alternative fix is for KVM to unconditionally honor the guest memory type (unless it is MMIO, to avoid MCEs on Intel). I believe the alternative fix is how things are on ARM, and probably also how things are on AMD.I am new to KVM and HW virtualization technologies. This series is meant as an RFC.
When we tried to do this in the past, we got machine checks everywhere unfortunately due to the same address being mapped with different memory types. Unfortunately I cannot find the entry anymore in bugzilla, but this was not fixed as far as I know.
Paolo
_______________________________________________
dri-devel mailing list
[email protected]
https://lists.freedesktop.org/mailman/listinfo/dri-devel
Quoted 15 lines · Paolo Bonzini
Quoted 13 lines · Chia-I Wu
Hi,
Host GPU drivers like to give userspace WC mapping. When the userspace makes the mapping available to a guest, it also tells the guest to create a WC mapping. However, even when the guest kernel picks the correct memory type, it gets ignored because of
VMX_EPT_IPAT_BITon Intel.This series adds a new flag to
KVM_SET_USER_MEMORY_REGION, which tells the host kernel to honor the guest memory type for the memslot. An alternative fix is for KVM to unconditionally honor the guest memory type (unless it is MMIO, to avoid MCEs on Intel). I believe the alternative fix is how things are on ARM, and probably also how things are on AMD.
Quoted 8 lines
Quoted 3 lines
I am new to KVM and HW virtualization technologies. This series is meant as an RFC.
When we tried to do this in the past, we got machine checks everywhere unfortunately due to the same address being mapped with different memory types. Unfortunately I cannot find the entry anymore in bugzilla, but this was not fixed as far as I know.
Yeah, I did a bit of history digging here
https://gitlab.freedesktop.org/virgl/virglrenderer/issues/151#note_372594
The bug you mentioned was probably this one
https://bugzilla.kernel.org/show_bug.cgi?id=104091
which was caused by
From what I can tell, the commit allowed the guests to create cached mappings to MMIO regions and caused MCEs. That is different than what I need, which is to allow guests to create uncached mappings to system ram (i.e., !kvm_is_mmio_pfn) when the host userspace also has uncached mappings. But it is true that this still allows the userspace & guest kernel to create conflicting memory types.
Implementation-wise, the current implementation uses kvm_arch_register_noncoherent_dma. It essentially treats a memslot with the new flag as a non-coherent vfio device as far as mmu is concerned.
Quoted 3 lines
Paolo
_______________________________________________
dri-devel mailing list
[email protected]
https://lists.freedesktop.org/mailman/listinfo/dri-devel
Paolo Bonzini
maintainerQuoted 4 lines · Chia-I Wu
The bug you mentioned was probably this one
Yes, indeed.
Quoted 6 lines
From what I can tell, the commit allowed the guests to create cached mappings to MMIO regions and caused MCEs. That is different than what I need, which is to allow guests to create uncached mappings to system ram (i.e., !kvm_is_mmio_pfn) when the host userspace also has uncached mappings. But it is true that this still allows the userspace & guest kernel to create conflicting memory types.
Right, the question is whether the MCEs were tied to MMIO regions specifically and if so why.
An interesting remark is in the footnote of table 11-7 in the SDM. There, for the MTRR (EPT for us) memory type UC you can read:
The UC attribute comes from the MTRRs and the processors are not required to snoop their caches since the data could never have been cached. This attribute is preferred for performance reasons.
There are two possibilities:
1) the footnote doesn't apply to UC mode coming from EPT page tables. That would make your change safe.
2) the footnote also applies when the UC attribute comes from the EPT page tables rather than the MTRRs. In that case, the host should use UC as the EPT page attribute if and only if it's consistent with the host MTRRs; it would be more or less impossible to honor UC in the guest MTRRs. In that case, something like the patch below would be needed.
It is not clear from the manual why the footnote would not apply to WC; that is, the manual doesn't say explicitly that the processor does not do snooping for accesses to WC memory. But I guess that must be the case, which is why I used MTRR_TYPE_WRCOMB in the patch below.
Either way, we would have an explanation of why creating cached mapping to MMIO regions would, and why in practice we're not seeing MCEs for guest RAM (the guest would have set WB for that memory in its MTRRs, not UC).
One thing you didn't say: how would userspace use KVM_MEM_DMA? On which regions would it be set?
Thanks,
Paolo
arch/x86/kvm/vmx/vmx.c +9 -1
@@ -6920,8 +6920,16 @@ static u64 vmx_get_mt_mask(struct kvm_vcpu *vcpu, gfn_t gfn, bool is_mmio) } cache =kvm_mtrr_get_guest_memory_type (vcpu, gfn); - exit: +if (cache ==MTRR_TYPE_UNCACHABLE && !is_mmio) { +/* +* We cannot set UC in the EPT page tables as it can cause +* machine check exceptions (??). Hopefully the guest is +* using PAT. +*/ + cache =MTRR_TYPE_WRCOMB ; + } +return (cache <<VMX_EPT_MT_EPTE_SHIFT ) | ipat; }
_______________________________________________
dri-devel mailing list
[email protected]
https://lists.freedesktop.org/mailman/listinfo/dri-devel
Quoted 14 lines · Paolo Bonzini
Quoted 4 lines · Chia-I Wu
The bug you mentioned was probably this one
Yes, indeed.
Quoted 6 lines
From what I can tell, the commit allowed the guests to create cached mappings to MMIO regions and caused MCEs. That is different than what I need, which is to allow guests to create uncached mappings to system ram (i.e., !kvm_is_mmio_pfn) when the host userspace also has uncached mappings. But it is true that this still allows the userspace & guest kernel to create conflicting memory types.
This is ok.
Quoted 2 lines
Right, the question is whether the MCEs were tied to MMIO regions specifically and if so why.
99.99999% likelihood the answer is "yes". Cacheable accesses to non-existent memory and most (all?) MMIO regions will cause a #MC. This includes speculative accesses.
Commit fd717f11015f ("KVM: x86: apply guest MTRR virtualization on host reserved pages") explicitly had a comment "1. MMIO: trust guest MTRR", which is basically a direct avenue to generating #MCs.
IIRC, WC accesses to non-existent memory will also cause #MC, but KVM has bigger problems if it has PRESENT EPTEs pointing at garbage.
Quoted 9 lines
An interesting remark is in the footnote of table 11-7 in the SDM. There, for the MTRR (EPT for us) memory type UC you can read:
The UC attribute comes from the MTRRs and the processors are not required to snoop their caches since the data could never have been cached. This attribute is preferred for performance reasons.
There are two possibilities:
Quoted 8 lines
1) the footnote doesn't apply to UC mode coming from EPT page tables. That would make your change safe.
2) the footnote also applies when the UC attribute comes from the EPT page tables rather than the MTRRs. In that case, the host should use UC as the EPT page attribute if and only if it's consistent with the host MTRRs; it would be more or less impossible to honor UC in the guest MTRRs. In that case, something like the patch below would be needed.
(2), the EPTs effectively replace the MTRRs. The expectation being that the VMM will use always use EPT memtypes consistent with the MTRRs.
Quoted 4 lines
It is not clear from the manual why the footnote would not apply to WC; that is, the manual doesn't say explicitly that the processor does not do snooping for accesses to WC memory. But I guess that must be the case, which is why I used
MTRR_TYPE_WRCOMBin the patch below.
A few paragraphs below table 11-12 states:
In particular, a WC page must never be aliased to a cacheable page because WC writes may not check the processor caches.
Quoted 3 lines
Either way, we would have an explanation of why creating cached mapping to MMIO regions would, and why in practice we're not seeing MCEs for guest RAM (the guest would have set WB for that memory in its MTRRs, not UC).
Aliasing (physical) RAM with different memtypes won't cause #MC, just memory corruption.
Quoted 14 lines
One thing you didn't say: how would userspace use
KVM_MEM_DMA? On which regions would it be set?Thanks,
Paolo
arch/x86/kvm/vmx/vmx.c +0
-0@@ -6920,8 +6920,16 @@ static u64 vmx_get_mt_mask(struct kvm_vcpu *vcpu, gfn_t gfn, bool is_mmio) }
arch/x86/kvm/vmx/vmx.c static u64 vmx_get_mt_mask(struct kvm_vcpu *vcpu, gfn_t gfn, bool is_mmio) · line 6930
Quoted 10 lines
arch/x86/kvm/vmx/vmx.c +7
-1cache =kvm_mtrr_get_guest_memory_type (vcpu, gfn); - exit: +if (cache ==MTRR_TYPE_UNCACHABLE && !is_mmio) { +/* +* We cannot set UC in the EPT page tables as it can cause +* machine check exceptions (??). Hopefully the guest is +* using PAT. +*/ + cache =MTRR_TYPE_WRCOMB ;
This is unnecessary. Setting UC in the EPT tables will never directly lead to #MC. Forcing WC is likely more dangerous.
Quoted 6 lines
arch/x86/kvm/vmx/vmx.c +2
-0+ } +return (cache <<VMX_EPT_MT_EPTE_SHIFT ) | ipat; }
Quoted 45 lines · Sean Christopherson
Quoted 14 lines · Paolo Bonzini
Quoted 4 lines · Chia-I Wu
The bug you mentioned was probably this one
Yes, indeed.
Quoted 6 lines
From what I can tell, the commit allowed the guests to create cached mappings to MMIO regions and caused MCEs. That is different than what I need, which is to allow guests to create uncached mappings to system ram (i.e., !kvm_is_mmio_pfn) when the host userspace also has uncached mappings. But it is true that this still allows the userspace & guest kernel to create conflicting memory types.
This is ok.
Quoted 2 lines
Right, the question is whether the MCEs were tied to MMIO regions specifically and if so why.
99.99999% likelihood the answer is "yes". Cacheable accesses to non-existent memory and most (all?) MMIO regions will cause a #MC. This includes speculative accesses.
Commit
fd717f11015f("KVM: x86: apply guest MTRR virtualization on host reserved pages") explicitly had a comment "1. MMIO: trust guest MTRR", which is basically a direct avenue to generating #MCs.IIRC, WC accesses to non-existent memory will also cause #MC, but KVM has bigger problems if it has PRESENT EPTEs pointing at garbage.
Quoted 12 lines
An interesting remark is in the footnote of table 11-7 in the SDM. There, for the MTRR (EPT for us) memory type UC you can read:
The UC attribute comes from the MTRRs and the processors are not required to snoop their caches since the data could never have been cached. This attribute is preferred for performance reasons.
There are two possibilities:
1) the footnote doesn't apply to UC mode coming from EPT page tables. That would make your change safe.
Quoted 8 lines
Quoted 5 lines
2) the footnote also applies when the UC attribute comes from the EPT page tables rather than the MTRRs. In that case, the host should use UC as the EPT page attribute if and only if it's consistent with the host MTRRs; it would be more or less impossible to honor UC in the guest MTRRs. In that case, something like the patch below would be needed.
(2), the EPTs effectively replace the MTRRs. The expectation being that the VMM will use always use EPT memtypes consistent with the MTRRs.
This is my understanding as well.
Quoted 10 lines
Quoted 4 lines
It is not clear from the manual why the footnote would not apply to WC; that is, the manual doesn't say explicitly that the processor does not do snooping for accesses to WC memory. But I guess that must be the case, which is why I used
MTRR_TYPE_WRCOMBin the patch below.A few paragraphs below table 11-12 states:
In particular, a WC page must never be aliased to a cacheable page because WC writes may not check the processor caches.
Quoted 6 lines
Quoted 3 lines
Either way, we would have an explanation of why creating cached mapping to MMIO regions would, and why in practice we're not seeing MCEs for guest RAM (the guest would have set WB for that memory in its MTRRs, not UC).
Aliasing (physical) RAM with different memtypes won't cause #MC, just memory corruption.
What we need potentially gives the userspace (the guest kernel, to be exact) the ability to create conflicting memory types. If we can be sure that the worst scenario is for a guest to corrupt its own memory, by only allowing aliases on physical ram, that seems alright.
AFAICT, it is currently allowed on ARM (verified) and AMD (not verified, but svm_get_mt_mask returns 0 which supposedly means the NPT does not restrict what the guest PAT can do). This diff would do the trick for Intel without needing any uapi change:
arch/x86/kvm/vmx/vmx.c +0 -0
@@ -6905,12 +6905,6 @@ static u64 vmx_get_mt_mask(struct kvm_vcpu
*vcpu, gfn_t gfn, bool is_mmio)
goto exit;
}- if (!kvm_arch_has_noncoherent_dma(vcpu->kvm)) {
- ipat = VMX_EPT_IPAT_BIT;
- cache = MTRR_TYPE_WRBACK;
- goto exit;
- }
-
if (kvm_read_cr0(vcpu) & X86_CR0_CD) {
ipat = VMX_EPT_IPAT_BIT;
if (kvm_check_has_quirk(vcpu->kvm, KVM_X86_QUIRK_CD_NW_CLEARED))Quoted 14 lines
Quoted 14 lines
One thing you didn't say: how would userspace use
KVM_MEM_DMA? On which regions would it be set?Thanks,
Paolo
arch/x86/kvm/vmx/vmx.c +0
-0@@ -6920,8 +6920,16 @@ static u64 vmx_get_mt_mask(struct kvm_vcpu *vcpu, gfn_t gfn, bool is_mmio) }
Quoted 20 lines
arch/x86/kvm/vmx/vmx.c static u64 vmx_get_mt_mask(struct kvm_vcpu *vcpu, gfn_t gfn, bool is_mmio) · line 6930
Quoted 10 lines
arch/x86/kvm/vmx/vmx.c +7
-1cache =kvm_mtrr_get_guest_memory_type (vcpu, gfn); - exit: +if (cache ==MTRR_TYPE_UNCACHABLE && !is_mmio) { +/* +* We cannot set UC in the EPT page tables as it can cause +* machine check exceptions (??). Hopefully the guest is +* using PAT. +*/ + cache =MTRR_TYPE_WRCOMB ;This is unnecessary. Setting UC in the EPT tables will never directly lead to #MC. Forcing WC is likely more dangerous.
Quoted 6 lines
arch/x86/kvm/vmx/vmx.c +2
-0+ } +return (cache <<VMX_EPT_MT_EPTE_SHIFT ) | ipat; }
_______________________________________________
dri-devel mailing list
[email protected]
https://lists.freedesktop.org/mailman/listinfo/dri-devel
Quoted 80 lines · Chia-I Wu
Quoted 45 lines · Sean Christopherson
Quoted 14 lines · Paolo Bonzini
Quoted 4 lines · Chia-I Wu
The bug you mentioned was probably this one
Yes, indeed.
Quoted 6 lines
From what I can tell, the commit allowed the guests to create cached mappings to MMIO regions and caused MCEs. That is different than what I need, which is to allow guests to create uncached mappings to system ram (i.e., !kvm_is_mmio_pfn) when the host userspace also has uncached mappings. But it is true that this still allows the userspace & guest kernel to create conflicting memory types.
This is ok.
Quoted 2 lines
Right, the question is whether the MCEs were tied to MMIO regions specifically and if so why.
99.99999% likelihood the answer is "yes". Cacheable accesses to non-existent memory and most (all?) MMIO regions will cause a #MC. This includes speculative accesses.
Commit
fd717f11015f("KVM: x86: apply guest MTRR virtualization on host reserved pages") explicitly had a comment "1. MMIO: trust guest MTRR", which is basically a direct avenue to generating #MCs.IIRC, WC accesses to non-existent memory will also cause #MC, but KVM has bigger problems if it has PRESENT EPTEs pointing at garbage.
Quoted 12 lines
An interesting remark is in the footnote of table 11-7 in the SDM. There, for the MTRR (EPT for us) memory type UC you can read:
The UC attribute comes from the MTRRs and the processors are not required to snoop their caches since the data could never have been cached. This attribute is preferred for performance reasons.
There are two possibilities:
1) the footnote doesn't apply to UC mode coming from EPT page tables. That would make your change safe.
Quoted 8 lines
Quoted 5 lines
2) the footnote also applies when the UC attribute comes from the EPT page tables rather than the MTRRs. In that case, the host should use UC as the EPT page attribute if and only if it's consistent with the host MTRRs; it would be more or less impossible to honor UC in the guest MTRRs. In that case, something like the patch below would be needed.
(2), the EPTs effectively replace the MTRRs. The expectation being that the VMM will use always use EPT memtypes consistent with the MTRRs.
This is my understanding as well.
Quoted 10 lines
Quoted 4 lines
It is not clear from the manual why the footnote would not apply to WC; that is, the manual doesn't say explicitly that the processor does not do snooping for accesses to WC memory. But I guess that must be the case, which is why I used
MTRR_TYPE_WRCOMBin the patch below.A few paragraphs below table 11-12 states:
In particular, a WC page must never be aliased to a cacheable page because WC writes may not check the processor caches.
Quoted 6 lines
Quoted 3 lines
Either way, we would have an explanation of why creating cached mapping to MMIO regions would, and why in practice we're not seeing MCEs for guest RAM (the guest would have set WB for that memory in its MTRRs, not UC).
Aliasing (physical) RAM with different memtypes won't cause #MC, just memory corruption.
What we need potentially gives the userspace (the guest kernel, to be exact) the ability to create conflicting memory types. If we can be sure that the worst scenario is for a guest to corrupt its own memory, by only allowing aliases on physical ram, that seems alright.
Quoted 4 lines
AFAICT, it is currently allowed on ARM (verified) and AMD (not verified, but
svm_get_mt_maskreturns 0 which supposedly means the NPT does not restrict what the guest PAT can do). This diff would do the trick for Intel without needing any uapi change:
I would be concerned about Intel CPU errata such as SKX40 and SKX59.
Quoted 7 lines · Jim Mattson
Quoted 4 lines · Chia-I Wu
AFAICT, it is currently allowed on ARM (verified) and AMD (not verified, but
svm_get_mt_maskreturns 0 which supposedly means the NPT does not restrict what the guest PAT can do). This diff would do the trick for Intel without needing any uapi change:I would be concerned about Intel CPU errata such as SKX40 and SKX59.
The part KVM cares about, #MC, is already addressed by forcing UC for MMIO. The data corruption issue is on the guest kernel to correctly use WC and/or non-temporal writes.
_______________________________________________
dri-devel mailing list
[email protected]
https://lists.freedesktop.org/mailman/listinfo/dri-devel
Paolo Bonzini
maintainerQuoted 9 lines · Sean Christopherson
Quoted 6 lines · Chia-I Wu
Quoted 4 lines
AFAICT, it is currently allowed on ARM (verified) and AMD (not verified, but
svm_get_mt_maskreturns 0 which supposedly means the NPT does not restrict what the guest PAT can do). This diff would do the trick for Intel without needing any uapi change:I would be concerned about Intel CPU errata such as SKX40 and SKX59.
The part KVM cares about, #MC, is already addressed by forcing UC for MMIO. The data corruption issue is on the guest kernel to correctly use WC and/or non-temporal writes.
What about coherency across live migration? The userspace process would use cached accesses, and also a WBINVD could potentially corrupt guest memory.
Paolo
Quoted 6 lines · Paolo Bonzini
Quoted 5 lines · Sean Christopherson
Quoted 5 lines · Chia-I Wu
Quoted 4 lines
AFAICT, it is currently allowed on ARM (verified) and AMD (not verified, but
svm_get_mt_maskreturns 0 which supposedly means the NPT does not restrict what the guest PAT can do). This diff would do the trick for Intel without needing any uapi change:
Quoted 8 lines
Quoted 4 lines
Quoted 1 line
I would be concerned about Intel CPU errata such as SKX40 and SKX59.
The part KVM cares about, #MC, is already addressed by forcing UC for MMIO. The data corruption issue is on the guest kernel to correctly use WC and/or non-temporal writes.
What about coherency across live migration? The userspace process would use cached accesses, and also a WBINVD could potentially corrupt guest memory.
Haven't given it an iota of thought. My comments were purely in the context of the SKX40 and SKX59 errata, which are silly bugs that no real world software will ever hit, e.g. no sane software is going to split a MASKMOV instruction across address spaces. Hitting SKX59 would further require the kernel to map MMIO as WB directly adjacent to RAM, which is beyond crazy.
Quoted 11 lines
From: Paolo Bonzini
Sent: Wednesday, February 19, 2020 12:29 AMQuoted 3 lines · Sean Christopherson
Quoted 3 lines · Chia-I Wu
Quoted 2 lines
AFAICT, it is currently allowed on ARM (verified) and AMD (not verified, but
svm_get_mt_maskreturns 0 which supposedly means theNPT
Quoted 3 lines
Quoted 3 lines
Quoted 2 lines
does not restrict what the guest PAT can do). This diff would do the trick for Intel without needing any uapi change:
I would be concerned about Intel CPU errata such as SKX40 and SKX59.
Quoted 9 lines
Quoted 1 line
The part KVM cares about, #MC, is already addressed by forcing UC for
MMIO.
Quoted 2 lines
The data corruption issue is on the guest kernel to correctly use WC and/or non-temporal writes.
What about coherency across live migration? The userspace process would use cached accesses, and also a WBINVD could potentially corrupt guest memory.
In such case the userspace process possibly should conservatively use UC mapping, as if for MMIO regions on a passthrough device. However there remains a problem. the definition of KVM_MEM_DMA implies favoring guest setting, which could be whatever type in concept. Then assuming UC is also problematic. I'm not sure whether inventing another interface to query effective memory type from KVM is a good idea. There is no guarantee that the guest will use same type for every page in the same slot, then such interface might be messy. Alternatively, maybe we could just have an interface for KVM userspace to force memory type for a given slot, if it is mainly used in para-virtualized scenarios (e.g. virtio-gpu) where the guest is enlightened to use a forced type (e.g. WC)?
Thanks
Kevin
Quoted 22 lines · Kevin
Quoted 12 lines
From: Paolo Bonzini
Sent: Wednesday, February 19, 2020 12:29 AMQuoted 3 lines · Sean Christopherson
Quoted 3 lines · Chia-I Wu
Quoted 2 lines
AFAICT, it is currently allowed on ARM (verified) and AMD (not verified, but
svm_get_mt_maskreturns 0 which supposedly means theNPT
Quoted 3 lines
Quoted 3 lines
Quoted 2 lines
does not restrict what the guest PAT can do). This diff would do the trick for Intel without needing any uapi change:
I would be concerned about Intel CPU errata such as SKX40 and SKX59.
Quoted 9 lines
Quoted 1 line
The part KVM cares about, #MC, is already addressed by forcing UC for
MMIO.
Quoted 2 lines
The data corruption issue is on the guest kernel to correctly use WC and/or non-temporal writes.
What about coherency across live migration? The userspace process would use cached accesses, and also a WBINVD could potentially corrupt guest memory.
Quoted 11 lines
In such case the userspace process possibly should conservatively use UC mapping, as if for MMIO regions on a passthrough device. However there remains a problem. the definition of
KVM_MEM_DMAimplies favoring guest setting, which could be whatever type in concept. Then assuming UC is also problematic. I'm not sure whether inventing another interface to query effective memory type from KVM is a good idea. There is no guarantee that the guest will use same type for every page in the same slot, then such interface might be messy. Alternatively, maybe we could just have an interface for KVM userspace to force memory type for a given slot, if it is mainly used in para-virtualized scenarios (e.g. virtio-gpu) where the guest is enlightened to use a forced type (e.g. WC)?
KVM forcing the memory type for a given slot should work too. But the ignore-guest-pat bit seems to be Intel-specific. We will need to define how the second-level page attributes combine with the guest page attributes somehow.
KVM should in theory be able to tell that the userspace region is mapped with a certain memory type and can force the same memory type onto the guest. The userspace does not need to be involved. But that sounds very slow? This may be a dumb question, but would it help to add KVM_SET_DMA_BUF and let KVM negotiate the memory type with the in-kernel GPU drivers?
Quoted 3 lines
Thanks
Kevin
_______________________________________________
dri-devel mailing list
[email protected]
https://lists.freedesktop.org/mailman/listinfo/dri-devel
Quoted 39 lines
From: Chia-I Wu <[email protected]>
Sent: Thursday, February 20, 2020 3:37 AMQuoted 8 lines · Kevin
Quoted 8 lines
From: Paolo Bonzini
Sent: Wednesday, February 19, 2020 12:29 AMQuoted 3 lines · Sean Christopherson
Quoted 3 lines · Chia-I Wu
Quoted 2 lines
AFAICT, it is currently allowed on ARM (verified) and AMD (not verified, but
svm_get_mt_maskreturns 0 which supposedly meansthe
Quoted 10 lines
Quoted 10 lines
NPT
Quoted 4 lines
Quoted 3 lines
Quoted 2 lines
does not restrict what the guest PAT can do). This diff would do the trick for Intel without needing any uapi change:
I would be concerned about Intel CPU errata such as SKX40 and SKX59.
The part KVM cares about, #MC, is already addressed by forcing UC for
MMIO.
Quoted 2 lines
The data corruption issue is on the guest kernel to correctly use WC and/or non-temporal writes.
What about coherency across live migration? The userspace process
would
Quoted 4 lines
Quoted 3 lines
use cached accesses, and also a WBINVD could potentially corrupt guest memory.
Quoted 11 lines
In such case the userspace process possibly should conservatively use UC mapping, as if for MMIO regions on a passthrough device. However there remains a problem. the definition of
KVM_MEM_DMAimplies favoring guest setting, which could be whatever type in concept. Then assuming UC is also problematic. I'm not sure whether inventing another interface to query effective memory type from KVM is a good idea. There is no guarantee that the guest will use same type for every page in the same slot, then such interface might be messy. Alternatively, maybe we could just have an interface for KVM userspace to force memory type for a given slot, if it is mainly used in para-virtualized scenarios (e.g. virtio-gpu) where the guest is enlightened to use a forced type (e.g. WC)?
Quoted 4 lines
KVM forcing the memory type for a given slot should work too. But the ignore-guest-pat bit seems to be Intel-specific. We will need to define how the second-level page attributes combine with the guest page attributes somehow.
oh, I'm not aware of that difference. without an ipat-equivalent capability, I'm not sure how to forcing random type here. If you look at table 11-7 in Intel SDM, none of MTRR (EPT) memory type can lead to consistent effective type when combining with random PAT value. So
it is definitely a dead end.
Quoted 9 lines
KVM should in theory be able to tell that the userspace region is mapped with a certain memory type and can force the same memory type onto the guest. The userspace does not need to be involved. But that sounds very slow? This may be a dumb question, but would it help to add
KVM_SET_DMA_BUFand let KVM negotiate the memory type with the in-kernel GPU drivers?
KVM_SET_DMA_BUF looks more reasonable. But I guess we don't need KVM to be aware of such negotiation. We can continue your original proposal to have KVM simply favor guest memory type (maybe still call KVM_MEM_DMA). On the other hand, Qemu should just mmap on the fd handle of the dmabuf passed from the virtio-gpu device backend, e.g. to conduct migration. That way the mmap request is finally served by DRM and underlying GPU drivers, with proper type enforced automatically.
Thanks
Kevin
Quoted 66 lines
From: Tian, Kevin
Sent: Thursday, February 20, 2020 10:05 AMQuoted 10 lines
From: Chia-I Wu <[email protected]>
Sent: Thursday, February 20, 2020 3:37 AMQuoted 6 lines · Kevin
Quoted 6 lines
From: Paolo Bonzini
Sent: Wednesday, February 19, 2020 12:29 AMQuoted 1 line · Sean Christopherson
Quoted 1 line
On Fri, Feb 14, 2020 at 1:47 PM Chia-I Wu <[email protected]>
Quoted 7 lines · wrote:
Quoted 2 lines
Quoted 2 lines
Quoted 2 lines
Quoted 2 lines
Quoted 2 lines
AFAICT, it is currently allowed on ARM (verified) and AMD (not verified, but
svm_get_mt_maskreturns 0 which supposedly meansthe
Quoted 4 lines
Quoted 4 lines
NPT
Quoted 3 lines
Quoted 3 lines
Quoted 2 lines
does not restrict what the guest PAT can do). This diff would do the trick for Intel without needing any uapi change:
I would be concerned about Intel CPU errata such as SKX40 and
SKX59.
Quoted 1 line
Quoted 1 line
Quoted 1 line
Quoted 1 line
The part KVM cares about, #MC, is already addressed by forcing UC
for
Quoted 21 lines
Quoted 5 lines
Quoted 5 lines
MMIO.
Quoted 2 lines
The data corruption issue is on the guest kernel to correctly use WC and/or non-temporal writes.
What about coherency across live migration? The userspace process
would
Quoted 4 lines
Quoted 3 lines
use cached accesses, and also a WBINVD could potentially corrupt guest memory.
Quoted 11 lines
In such case the userspace process possibly should conservatively use UC mapping, as if for MMIO regions on a passthrough device. However there remains a problem. the definition of
KVM_MEM_DMAimplies favoring guest setting, which could be whatever type in concept. Then assuming UC is also problematic. I'm not sure whether inventing another interface to query effective memory type from KVM is a good idea. There is no guarantee that the guest will use same type for every page in the same slot, then such interface might be messy. Alternatively, maybe we could just have an interface for KVM userspace to force memory type for a given slot, if it is mainly used in para-virtualized scenarios (e.g. virtio-gpu) where the guest is enlightened to use a forced type (e.g. WC)?Quoted 4 lines
KVM forcing the memory type for a given slot should work too. But the ignore-guest-pat bit seems to be Intel-specific. We will need to define how the second-level page attributes combine with the guest page attributes somehow.
oh, I'm not aware of that difference. without an ipat-equivalent capability, I'm not sure how to forcing random type here. If you look at table 11-7 in Intel SDM, none of MTRR (EPT) memory type can lead to consistent effective type when combining with random PAT value. So
it is definitely a dead end.Quoted 9 lines
KVM should in theory be able to tell that the userspace region is mapped with a certain memory type and can force the same memory type onto the guest. The userspace does not need to be involved. But that sounds very slow? This may be a dumb question, but would it help to add
KVM_SET_DMA_BUFand let KVM negotiate the memory type with the in-kernel GPU drivers?
Quoted 8 lines
KVM_SET_DMA_BUFlooks more reasonable. But I guess we don't need KVM to be aware of such negotiation. We can continue your original proposal to have KVM simply favor guest memory type (maybe still callKVM_MEM_DMA). On the other hand, Qemu should just mmap on the fd handle of the dmabuf passed from the virtio-gpu device backend, e.g. to conduct migration. That way the mmap request is finally served by DRM and underlying GPU drivers, with proper type enforced automatically.
Thinking more possibly we don't need introduce new interface to KVM. As long as Qemu uses dmabuf interface to mmap the specific region, KVM can simply check memory type in host page table given hva of a memslot. If the type is UC or WC, it implies that userspace wants a non-coherent mapping which should be reflected in the guest side too. In such case, KVM can go to non-cohenrent DMA path and favor guest memory type automatically.
Thanks
Kevin
Quoted 76 lines · Kevin
Quoted 67 lines
From: Tian, Kevin
Sent: Thursday, February 20, 2020 10:05 AMQuoted 10 lines
From: Chia-I Wu <[email protected]>
Sent: Thursday, February 20, 2020 3:37 AMQuoted 6 lines · Kevin
Quoted 6 lines
From: Paolo Bonzini
Sent: Wednesday, February 19, 2020 12:29 AMQuoted 1 line · Sean Christopherson
Quoted 1 line
On Fri, Feb 14, 2020 at 1:47 PM Chia-I Wu <[email protected]>
Quoted 7 lines · wrote:
Quoted 2 lines
Quoted 2 lines
Quoted 2 lines
Quoted 2 lines
Quoted 2 lines
AFAICT, it is currently allowed on ARM (verified) and AMD (not verified, but
svm_get_mt_maskreturns 0 which supposedly meansthe
Quoted 4 lines
Quoted 4 lines
NPT
Quoted 3 lines
Quoted 3 lines
Quoted 2 lines
does not restrict what the guest PAT can do). This diff would do the trick for Intel without needing any uapi change:
I would be concerned about Intel CPU errata such as SKX40 and
SKX59.
Quoted 1 line
Quoted 1 line
Quoted 1 line
Quoted 1 line
The part KVM cares about, #MC, is already addressed by forcing UC
for
Quoted 21 lines
Quoted 5 lines
Quoted 5 lines
MMIO.
Quoted 2 lines
The data corruption issue is on the guest kernel to correctly use WC and/or non-temporal writes.
What about coherency across live migration? The userspace process
would
Quoted 4 lines
Quoted 3 lines
use cached accesses, and also a WBINVD could potentially corrupt guest memory.
Quoted 11 lines
In such case the userspace process possibly should conservatively use UC mapping, as if for MMIO regions on a passthrough device. However there remains a problem. the definition of
KVM_MEM_DMAimplies favoring guest setting, which could be whatever type in concept. Then assuming UC is also problematic. I'm not sure whether inventing another interface to query effective memory type from KVM is a good idea. There is no guarantee that the guest will use same type for every page in the same slot, then such interface might be messy. Alternatively, maybe we could just have an interface for KVM userspace to force memory type for a given slot, if it is mainly used in para-virtualized scenarios (e.g. virtio-gpu) where the guest is enlightened to use a forced type (e.g. WC)?Quoted 4 lines
KVM forcing the memory type for a given slot should work too. But the ignore-guest-pat bit seems to be Intel-specific. We will need to define how the second-level page attributes combine with the guest page attributes somehow.
oh, I'm not aware of that difference. without an ipat-equivalent capability, I'm not sure how to forcing random type here. If you look at table 11-7 in Intel SDM, none of MTRR (EPT) memory type can lead to consistent effective type when combining with random PAT value. So
it is definitely a dead end.Quoted 9 lines
KVM should in theory be able to tell that the userspace region is mapped with a certain memory type and can force the same memory type onto the guest. The userspace does not need to be involved. But that sounds very slow? This may be a dumb question, but would it help to add
KVM_SET_DMA_BUFand let KVM negotiate the memory type with the in-kernel GPU drivers?Quoted 8 lines
KVM_SET_DMA_BUFlooks more reasonable. But I guess we don't need KVM to be aware of such negotiation. We can continue your original proposal to have KVM simply favor guest memory type (maybe still callKVM_MEM_DMA). On the other hand, Qemu should just mmap on the fd handle of the dmabuf passed from the virtio-gpu device backend, e.g. to conduct migration. That way the mmap request is finally served by DRM and underlying GPU drivers, with proper type enforced automatically.
Quoted 7 lines
Thinking more possibly we don't need introduce new interface to KVM. As long as Qemu uses dmabuf interface to mmap the specific region, KVM can simply check memory type in host page table given hva of a memslot. If the type is UC or WC, it implies that userspace wants a non-coherent mapping which should be reflected in the guest side too. In such case, KVM can go to non-cohenrent DMA path and favor guest memory type automatically.
Sorry, I mixed two things together.
Userspace access to dmabuf mmap must be guarded by DMA_BUF_SYNC_{START,END} ioctls. It is possible that the GPU driver always picks a WB mapping and let the ioctls flush/invalidate CPU caches. We actually want the guest memory type to match vkMapMemory's memory type, which can be different from dmabuf mmap's memory type. It is not enough for KVM to inspect the hva's memory type.
KVM_SET_DMA_BUF, if supported, is a signal to KVM that the guest memory type should be honored (or forced if there is a new op in dma_buf_ops that tells KVM which memory type to force). KVM_MEM_DMA flag in this RFC sends the same signal. Unless KVM_SET_DMA_BUF gives the userspace other features such as setting unlimited number of dmabufs to subregions of a memslot, it is not very useful.
If uapi change is to be avoided, it is the easiest that guest memory type is always honored unless it causes #MC (i.e.,is_mmio==true).
Quoted 3 lines
Thanks
Kevin
_______________________________________________
dri-devel mailing list
[email protected]
https://lists.freedesktop.org/mailman/listinfo/dri-devel
Quoted 102 lines
From: Chia-I Wu <[email protected]>
Sent: Friday, February 21, 2020 6:24 AMQuoted 8 lines · Kevin
Quoted 8 lines
From: Tian, Kevin
Sent: Thursday, February 20, 2020 10:05 AMQuoted 4 lines
From: Chia-I Wu <[email protected]>
Sent: Thursday, February 20, 2020 3:37 AMOn Wed, Feb 19, 2020 at 1:52 AM Tian, Kevin <[email protected]>
Quoted 9 lines · wrote:
Quoted 9 lines
Quoted 6 lines
Quoted 6 lines
Quoted 6 lines
From: Paolo Bonzini
Sent: Wednesday, February 19, 2020 12:29 AMQuoted 1 line · Sean Christopherson
Quoted 1 line
On Fri, Feb 14, 2020 at 1:47 PM Chia-I Wu <[email protected]>
Quoted 2 lines · wrote:
Quoted 2 lines
Quoted 2 lines
Quoted 2 lines
Quoted 2 lines
Quoted 2 lines
AFAICT, it is currently allowed on ARM (verified) and AMD (not verified, but
svm_get_mt_maskreturns 0 which supposedlymeans
Quoted 3 lines
Quoted 3 lines
Quoted 3 lines
the
Quoted 2 lines
Quoted 2 lines
NPT
Quoted 1 line
Quoted 1 line
Quoted 1 line
does not restrict what the guest PAT can do). This diff would do
the
Quoted 4 lines
Quoted 4 lines
Quoted 2 lines
Quoted 2 lines
Quoted 2 lines
Quoted 2 lines
Quoted 2 lines
Quoted 1 line
trick for Intel without needing any uapi change:
I would be concerned about Intel CPU errata such as SKX40 and
SKX59.
Quoted 1 line
Quoted 1 line
Quoted 1 line
Quoted 1 line
The part KVM cares about, #MC, is already addressed by forcing
UC
Quoted 3 lines
Quoted 3 lines
for
Quoted 2 lines
Quoted 2 lines
Quoted 2 lines
MMIO.
Quoted 1 line
The data corruption issue is on the guest kernel to correctly use
WC
Quoted 3 lines
Quoted 3 lines
Quoted 3 lines
Quoted 3 lines
Quoted 3 lines
Quoted 1 line
and/or non-temporal writes.
What about coherency across live migration? The userspace
process
Quoted 2 lines
Quoted 2 lines
Quoted 2 lines
would
Quoted 1 line
Quoted 1 line
use cached accesses, and also a WBINVD could potentially corrupt
guest
Quoted 5 lines
Quoted 5 lines
Quoted 5 lines
Quoted 5 lines
Quoted 2 lines
memory.
In such case the userspace process possibly should conservatively use UC mapping, as if for MMIO regions on a passthrough device.
However
Quoted 3 lines
Quoted 3 lines
Quoted 3 lines
Quoted 3 lines
there remains a problem. the definition of
KVM_MEM_DMAimplies favoring guest setting, which could be whatever type in concept. Then assuming UC is also problematic. I'm not sure whether inventinganother
Quoted 1 line
Quoted 1 line
Quoted 1 line
Quoted 1 line
interface to query effective memory type from KVM is a good idea.
There
Quoted 3 lines
Quoted 3 lines
Quoted 3 lines
Quoted 3 lines
is no guarantee that the guest will use same type for every page in the same slot, then such interface might be messy. Alternatively, maybe we could just have an interface for KVM userspace to force memory
type
Quoted 2 lines
Quoted 2 lines
Quoted 2 lines
Quoted 2 lines
for a given slot, if it is mainly used in para-virtualized scenarios (e.g. virtio-gpu) where the guest is enlightened to use a forced type (e.g.
WC)?
Quoted 12 lines
Quoted 12 lines
Quoted 4 lines
KVM forcing the memory type for a given slot should work too. But the ignore-guest-pat bit seems to be Intel-specific. We will need to define how the second-level page attributes combine with the guest page attributes somehow.
oh, I'm not aware of that difference. without an ipat-equivalent capability, I'm not sure how to forcing random type here. If you look at table 11-7 in Intel SDM, none of MTRR (EPT) memory type can lead to consistent effective type when combining with random PAT value. So
it is definitely a dead end.Quoted 1 line
Quoted 2 lines
Quoted 2 lines
Quoted 2 lines
KVM should in theory be able to tell that the userspace region is mapped with a certain memory type and can force the same memory
type
Quoted 3 lines
Quoted 3 lines
Quoted 3 lines
onto the guest. The userspace does not need to be involved. But that sounds very slow? This may be a dumb question, but would it help to add
KVM_SET_DMA_BUFand let KVM negotiate the memory type withthe
Quoted 11 lines
Quoted 11 lines
Quoted 3 lines
in-kernel GPU drivers?
KVM_SET_DMA_BUFlooks more reasonable. But I guess we don't need KVM to be aware of such negotiation. We can continue your original proposal to have KVM simply favor guest memory type (maybe still callKVM_MEM_DMA). On the other hand, Qemu should just mmap on the fd handle of the dmabuf passed from the virtio-gpu device backend, e.g. to conduct migration. That way the mmap request is finally served by DRM and underlying GPU drivers, with proper type enforcedautomatically.
Quoted 9 lines
Quoted 1 line
Thinking more possibly we don't need introduce new interface to KVM. As long as Qemu uses dmabuf interface to mmap the specific region, KVM can simply check memory type in host page table given hva of a memslot. If the type is UC or WC, it implies that userspace wants a non-coherent mapping which should be reflected in the guest side too. In such case, KVM can go to non-cohenrent DMA path and favor guest memory type automatically.
Quoted 8 lines
Sorry, I mixed two things together.
Userspace access to dmabuf mmap must be guarded by DMA_BUF_SYNC_{START,END} ioctls. It is possible that the GPU driver always picks a WB mapping and let the ioctls flush/invalidate CPU caches. We actually want the guest memory type to match vkMapMemory's memory type, which can be different from dmabuf mmap's memory type. It is not enough for KVM to inspect the hva's memory type.
I'm not familiar with dmabuf and what is the difference between vkMapMemory and mmap. Just a simple thought that whatever memory type/synchronization enforced on the host userspace should ideally be applied to guest userspace too. e.g. in above example we possibly want the guest to use WB and issue flush/invalidate hypercalls to guard with other potential parallel operations in the host side. otherwise I cannot see how synchronization can be done when one use WB with sync primitives while the other simply use WC w/o such primitives.
Quoted 7 lines
KVM_SET_DMA_BUF, if supported, is a signal to KVM that the guest memory type should be honored (or forced if there is a new op indma_buf_opsthat tells KVM which memory type to force).KVM_MEM_DMAflag in this RFC sends the same signal. UnlessKVM_SET_DMA_BUFgives the userspace other features such as setting unlimited number of dmabufs to subregions of a memslot, it is not very useful.
the good part of a new interface is its simplicity, but only in slot granularity. instead having KVM to inspect hva can support page granularity, but adding run-time overhead. Let's see how Paolo thinks. 😊
Quoted 4 lines
If uapi change is to be avoided, it is the easiest that guest memory type is always honored unless it causes #MC (i.e.,is_mmio==true).
I feel this goes too far...
Thanks
Kevin
Quoted 130 lines · Kevin
Quoted 4 lines
From: Chia-I Wu <[email protected]>
Sent: Friday, February 21, 2020 6:24 AMOn Wed, Feb 19, 2020 at 6:38 PM Tian, Kevin <[email protected]>
Quoted 7 lines · wrote:
Quoted 7 lines
Quoted 7 lines
From: Tian, Kevin
Sent: Thursday, February 20, 2020 10:05 AMQuoted 3 lines
From: Chia-I Wu <[email protected]>
Sent: Thursday, February 20, 2020 3:37 AMQuoted 8 lines
Quoted 1 line
Quoted 1 line
Quoted 1 line
On Wed, Feb 19, 2020 at 1:52 AM Tian, Kevin <[email protected]>
Quoted 6 lines · wrote:
Quoted 6 lines
Quoted 6 lines
Quoted 6 lines
Quoted 6 lines
From: Paolo Bonzini
Sent: Wednesday, February 19, 2020 12:29 AMQuoted 1 line · Sean Christopherson
Quoted 1 line
On Fri, Feb 14, 2020 at 1:47 PM Chia-I Wu <
Quoted 2 lines
Quoted 2 lines
Quoted 2 lines
Quoted 1 line · wrote:
Quoted 1 line
Quoted 1 line
Quoted 1 line
Quoted 1 line
Quoted 1 line
AFAICT, it is currently allowed on ARM (verified) and AMD
(not
Quoted 5 lines
Quoted 1 line
Quoted 1 line
Quoted 1 line
Quoted 1 line
Quoted 1 line
Quoted 1 line
Quoted 1 line
Quoted 1 line
verified, but
svm_get_mt_maskreturns 0 which supposedlymeans
Quoted 3 lines
Quoted 3 lines
Quoted 3 lines
the
Quoted 2 lines
Quoted 2 lines
NPT
Quoted 1 line
Quoted 1 line
Quoted 1 line
does not restrict what the guest PAT can do). This diff
would do
Quoted 3 lines
the
Quoted 2 lines
Quoted 2 lines
Quoted 2 lines
Quoted 2 lines
Quoted 2 lines
Quoted 2 lines
Quoted 2 lines
Quoted 1 line
trick for Intel without needing any uapi change:
I would be concerned about Intel CPU errata such as SKX40
and
Quoted 2 lines
Quoted 2 lines
Quoted 2 lines
SKX59.
Quoted 1 line
Quoted 1 line
Quoted 1 line
Quoted 1 line
The part KVM cares about, #MC, is already addressed by
forcing
Quoted 4 lines
UC
Quoted 3 lines
Quoted 3 lines
for
Quoted 2 lines
Quoted 2 lines
Quoted 2 lines
MMIO.
Quoted 1 line
The data corruption issue is on the guest kernel to
correctly use
Quoted 7 lines
WC
Quoted 3 lines
Quoted 3 lines
Quoted 3 lines
Quoted 3 lines
Quoted 3 lines
Quoted 1 line
and/or non-temporal writes.
What about coherency across live migration? The userspace
process
Quoted 2 lines
Quoted 2 lines
Quoted 2 lines
would
Quoted 1 line
Quoted 1 line
use cached accesses, and also a WBINVD could potentially
corrupt
Quoted 5 lines
guest
Quoted 4 lines
Quoted 4 lines
Quoted 4 lines
Quoted 4 lines
Quoted 2 lines
memory.
In such case the userspace process possibly should
conservatively use
Quoted 4 lines
Quoted 1 line
Quoted 1 line
Quoted 1 line
Quoted 1 line
UC mapping, as if for MMIO regions on a passthrough device.
However
Quoted 2 lines
Quoted 2 lines
Quoted 2 lines
Quoted 2 lines
there remains a problem. the definition of
KVM_MEM_DMAimplies favoring guest setting, which could be whatever type in concept.Then
Quoted 5 lines
Quoted 1 line
Quoted 1 line
Quoted 1 line
Quoted 1 line
assuming UC is also problematic. I'm not sure whether inventing
another
Quoted 1 line
Quoted 1 line
Quoted 1 line
Quoted 1 line
interface to query effective memory type from KVM is a good idea.
There
Quoted 1 line
Quoted 1 line
Quoted 1 line
Quoted 1 line
is no guarantee that the guest will use same type for every page
in the
Quoted 1 line
Quoted 1 line
Quoted 1 line
Quoted 1 line
Quoted 1 line
same slot, then such interface might be messy. Alternatively,
maybe
Quoted 3 lines
Quoted 1 line
Quoted 1 line
Quoted 1 line
Quoted 1 line
we could just have an interface for KVM userspace to force memory
type
Quoted 1 line
Quoted 1 line
Quoted 1 line
Quoted 1 line
for a given slot, if it is mainly used in para-virtualized
scenarios (e.g.
Quoted 1 line
Quoted 1 line
Quoted 1 line
Quoted 1 line
Quoted 1 line
virtio-gpu) where the guest is enlightened to use a forced type
(e.g.
Quoted 2 lines
WC)?
Quoted 1 line
Quoted 1 line
Quoted 1 line
KVM forcing the memory type for a given slot should work too. But
the
Quoted 6 lines
Quoted 6 lines
Quoted 6 lines
Quoted 3 lines
ignore-guest-pat bit seems to be Intel-specific. We will need to define how the second-level page attributes combine with the guest page attributes somehow.
oh, I'm not aware of that difference. without an ipat-equivalent capability, I'm not sure how to forcing random type here. If you
look at
Quoted 9 lines
Quoted 7 lines
Quoted 7 lines
table 11-7 in Intel SDM, none of MTRR (EPT) memory type can lead to consistent effective type when combining with random PAT value. So
it is definitely a dead end.Quoted 3 lines
KVM should in theory be able to tell that the userspace region is mapped with a certain memory type and can force the same memory
type
Quoted 1 line
Quoted 1 line
Quoted 1 line
onto the guest. The userspace does not need to be involved. But
that
Quoted 1 line
Quoted 1 line
Quoted 1 line
Quoted 1 line
sounds very slow? This may be a dumb question, but would it help
to
Quoted 11 lines
Quoted 1 line
Quoted 1 line
Quoted 1 line
add
KVM_SET_DMA_BUFand let KVM negotiate the memory type withthe
Quoted 9 lines
Quoted 9 lines
Quoted 3 lines
in-kernel GPU drivers?
KVM_SET_DMA_BUFlooks more reasonable. But I guess we don't need KVM to be aware of such negotiation. We can continue your original proposal to have KVM simply favor guest memory type (maybe still callKVM_MEM_DMA). On the other hand, Qemu should just mmap on the fd handle of the dmabuf passed from the virtio-gpu device backend,e.g.
Quoted 12 lines
Quoted 2 lines
Quoted 2 lines
to conduct migration. That way the mmap request is finally served by DRM and underlying GPU drivers, with proper type enforced
automatically.
Quoted 9 lines
Quoted 1 line
Thinking more possibly we don't need introduce new interface to KVM. As long as Qemu uses dmabuf interface to mmap the specific region, KVM can simply check memory type in host page table given hva of a memslot. If the type is UC or WC, it implies that userspace wants a non-coherent mapping which should be reflected in the guest side too. In such case, KVM can go to non-cohenrent DMA path and favor guest memory type automatically.
Quoted 8 lines
Sorry, I mixed two things together.
Userspace access to dmabuf mmap must be guarded by DMA_BUF_SYNC_{START,END} ioctls. It is possible that the GPU driver always picks a WB mapping and let the ioctls flush/invalidate CPU caches. We actually want the guest memory type to match vkMapMemory's memory type, which can be different from dmabuf mmap's memory type. It is not enough for KVM to inspect the hva's memory type.
Quoted 10 lines
I'm not familiar with dmabuf and what is the difference between vkMapMemory and mmap. Just a simple thought that whatever memory type/synchronization enforced on the host userspace should ideally be applied to guest userspace too. e.g. in above example we possibly want the guest to use WB and issue flush/invalidate hypercalls to guard with other potential parallel operations in the host side. otherwise I cannot see how synchronization can be done when one use WB with sync primitives while the other simply use WC w/o such primitives.
I am reasonably familiar with the GPU stacks, but I am not familiar with KVM :)
When allocating a GPU memory, the userspace can specify whether it wants a coherent one or an incoherent one. vkMapMemory returns a coherent or a incoherent mapping respectively. Indeed we also want the guest userspace to have a coherent or a incoherent mapping respectively.
The GPU memory can be exported as a dmabuf to share with another device or process. For security, we allocate the GPU memory in a GPU process and we export the dmabuf to the hypervisor. mmap of dmabuf semantically returns an incoherent mapping. As a result, the guest will set up a mapping that has the same memory type as the vkMapMemory mapping does, but the hva in KVM_SET_USER_MEMORY_REGION points to the dmabuf's incoherent mapping.
If you think it is the best for KVM to inspect hva to determine the memory type with page granularity, that is reasonable and should work for us too. The userspace can do something (e.g., add a GPU driver dependency to the hypervisor such that the dma-buf is imported as a GPU memory and mapped using vkMapMemory) or I can work with dma-buf maintainers to see if dma-buf's semantics can be changed.
Quoted 14 lines
Quoted 7 lines
KVM_SET_DMA_BUF, if supported, is a signal to KVM that the guest memory type should be honored (or forced if there is a new op indma_buf_opsthat tells KVM which memory type to force).KVM_MEM_DMAflag in this RFC sends the same signal. UnlessKVM_SET_DMA_BUFgives the userspace other features such as setting unlimited number of dmabufs to subregions of a memslot, it is not very useful.the good part of a new interface is its simplicity, but only in slot granularity. instead having KVM to inspect hva can support page granularity, but adding run-time overhead. Let's see how Paolo thinks. 😊
Quoted 1 line
Quoted 9 lines
Quoted 3 lines
If uapi change is to be avoided, it is the easiest that guest memory type is always honored unless it causes #MC (i.e.,is_mmio==true).
I feel this goes too far...
Thanks
Kevin
_______________________________________________
dri-devel mailing list
[email protected]
https://lists.freedesktop.org/mailman/listinfo/dri-devel
(resend because gmail did not format to plain text...)
Quoted 116 lines · Chia-I Wu
Quoted 112 lines · Kevin
Quoted 111 lines
From: Chia-I Wu <[email protected]>
Sent: Friday, February 21, 2020 6:24 AMQuoted 8 lines · Kevin
Quoted 8 lines
From: Tian, Kevin
Sent: Thursday, February 20, 2020 10:05 AMQuoted 4 lines
From: Chia-I Wu <[email protected]>
Sent: Thursday, February 20, 2020 3:37 AMOn Wed, Feb 19, 2020 at 1:52 AM Tian, Kevin <[email protected]>
Quoted 9 lines · wrote:
Quoted 9 lines
Quoted 6 lines
Quoted 6 lines
Quoted 6 lines
From: Paolo Bonzini
Sent: Wednesday, February 19, 2020 12:29 AMQuoted 1 line · Sean Christopherson
Quoted 1 line
On Fri, Feb 14, 2020 at 1:47 PM Chia-I Wu <[email protected]>
Quoted 2 lines · wrote:
Quoted 2 lines
Quoted 2 lines
Quoted 2 lines
Quoted 2 lines
Quoted 2 lines
AFAICT, it is currently allowed on ARM (verified) and AMD (not verified, but
svm_get_mt_maskreturns 0 which supposedlymeans
Quoted 3 lines
Quoted 3 lines
Quoted 3 lines
the
Quoted 2 lines
Quoted 2 lines
NPT
Quoted 1 line
Quoted 1 line
Quoted 1 line
does not restrict what the guest PAT can do). This diff would do
the
Quoted 4 lines
Quoted 4 lines
Quoted 2 lines
Quoted 2 lines
Quoted 2 lines
Quoted 2 lines
Quoted 2 lines
Quoted 1 line
trick for Intel without needing any uapi change:
I would be concerned about Intel CPU errata such as SKX40 and
SKX59.
Quoted 1 line
Quoted 1 line
Quoted 1 line
Quoted 1 line
The part KVM cares about, #MC, is already addressed by forcing
UC
Quoted 3 lines
Quoted 3 lines
for
Quoted 2 lines
Quoted 2 lines
Quoted 2 lines
MMIO.
Quoted 1 line
The data corruption issue is on the guest kernel to correctly use
WC
Quoted 3 lines
Quoted 3 lines
Quoted 3 lines
Quoted 3 lines
Quoted 3 lines
Quoted 1 line
and/or non-temporal writes.
What about coherency across live migration? The userspace
process
Quoted 2 lines
Quoted 2 lines
Quoted 2 lines
would
Quoted 1 line
Quoted 1 line
use cached accesses, and also a WBINVD could potentially corrupt
guest
Quoted 5 lines
Quoted 5 lines
Quoted 5 lines
Quoted 5 lines
Quoted 2 lines
memory.
In such case the userspace process possibly should conservatively use UC mapping, as if for MMIO regions on a passthrough device.
However
Quoted 3 lines
Quoted 3 lines
Quoted 3 lines
Quoted 3 lines
there remains a problem. the definition of
KVM_MEM_DMAimplies favoring guest setting, which could be whatever type in concept. Then assuming UC is also problematic. I'm not sure whether inventinganother
Quoted 1 line
Quoted 1 line
Quoted 1 line
Quoted 1 line
interface to query effective memory type from KVM is a good idea.
There
Quoted 3 lines
Quoted 3 lines
Quoted 3 lines
Quoted 3 lines
is no guarantee that the guest will use same type for every page in the same slot, then such interface might be messy. Alternatively, maybe we could just have an interface for KVM userspace to force memory
type
Quoted 2 lines
Quoted 2 lines
Quoted 2 lines
Quoted 2 lines
for a given slot, if it is mainly used in para-virtualized scenarios (e.g. virtio-gpu) where the guest is enlightened to use a forced type (e.g.
WC)?
Quoted 12 lines
Quoted 12 lines
Quoted 4 lines
KVM forcing the memory type for a given slot should work too. But the ignore-guest-pat bit seems to be Intel-specific. We will need to define how the second-level page attributes combine with the guest page attributes somehow.
oh, I'm not aware of that difference. without an ipat-equivalent capability, I'm not sure how to forcing random type here. If you look at table 11-7 in Intel SDM, none of MTRR (EPT) memory type can lead to consistent effective type when combining with random PAT value. So
it is definitely a dead end.Quoted 1 line
Quoted 2 lines
Quoted 2 lines
Quoted 2 lines
KVM should in theory be able to tell that the userspace region is mapped with a certain memory type and can force the same memory
type
Quoted 3 lines
Quoted 3 lines
Quoted 3 lines
onto the guest. The userspace does not need to be involved. But that sounds very slow? This may be a dumb question, but would it help to add
KVM_SET_DMA_BUFand let KVM negotiate the memory type withthe
Quoted 11 lines
Quoted 11 lines
Quoted 3 lines
in-kernel GPU drivers?
KVM_SET_DMA_BUFlooks more reasonable. But I guess we don't need KVM to be aware of such negotiation. We can continue your original proposal to have KVM simply favor guest memory type (maybe still callKVM_MEM_DMA). On the other hand, Qemu should just mmap on the fd handle of the dmabuf passed from the virtio-gpu device backend, e.g. to conduct migration. That way the mmap request is finally served by DRM and underlying GPU drivers, with proper type enforcedautomatically.
Quoted 9 lines
Quoted 1 line
Thinking more possibly we don't need introduce new interface to KVM. As long as Qemu uses dmabuf interface to mmap the specific region, KVM can simply check memory type in host page table given hva of a memslot. If the type is UC or WC, it implies that userspace wants a non-coherent mapping which should be reflected in the guest side too. In such case, KVM can go to non-cohenrent DMA path and favor guest memory type automatically.
Sorry, I mixed two things together.
Userspace access to dmabuf mmap must be guarded by DMA_BUF_SYNC_{START,END} ioctls. It is possible that the GPU driver always picks a WB mapping and let the ioctls flush/invalidate CPU caches. We actually want the guest memory type to match vkMapMemory's memory type, which can be different from dmabuf mmap's memory type. It is not enough for KVM to inspect the hva's memory type.
Quoted 10 lines
Quoted 9 lines
I'm not familiar with dmabuf and what is the difference between vkMapMemory and mmap. Just a simple thought that whatever memory type/synchronization enforced on the host userspace should ideally be applied to guest userspace too. e.g. in above example we possibly want the guest to use WB and issue flush/invalidate hypercalls to guard with other potential parallel operations in the host side. otherwise I cannot see how synchronization can be done when one use WB with sync primitives while the other simply use WC w/o such primitives.
I am reasonably familiar with the GPU stacks, but I am not familiar with KVM :)
When allocating a GPU memory, the userspace can specify whether it wants a coherent one or an incoherent one. vkMapMemory returns a coherent or a incoherent mapping respectively. Indeed we also want the guest userspace to have a coherent or a incoherent mapping respectively.
The GPU memory can be exported as a dmabuf to share with another device or process. For security, we allocate the GPU memory in a GPU process and we export the dmabuf to the hypervisor. mmap of dmabuf semantically returns an incoherent mapping. As a result, the guest will set up a mapping that has the same memory type as the vkMapMemory mapping does, but the hva in KVM_SET_USER_MEMORY_REGION points to the dmabuf's incoherent mapping.
If you think it is the best for KVM to inspect hva to determine the memory type with page granularity, that is reasonable and should work for us too. The userspace can do something (e.g., add a GPU driver dependency to the hypervisor such that the dma-buf is imported as a GPU memory and mapped using vkMapMemory) or I can work with dma-buf maintainers to see if dma-buf's semantics can be changed.
Quoted 24 lines
Quoted 24 lines
Quoted 9 lines
KVM_SET_DMA_BUF, if supported, is a signal to KVM that the guest memory type should be honored (or forced if there is a new op indma_buf_opsthat tells KVM which memory type to force).KVM_MEM_DMAflag in this RFC sends the same signal. UnlessKVM_SET_DMA_BUFgives the userspace other features such as setting unlimited number of dmabufs to subregions of a memslot, it is not very useful.the good part of a new interface is its simplicity, but only in slot granularity. instead having KVM to inspect hva can support page granularity, but adding run-time overhead. Let's see how Paolo thinks.
Quoted 4 lines
If uapi change is to be avoided, it is the easiest that guest memory type is always honored unless it causes #MC (i.e.,is_mmio==true).
I feel this goes too far...
Thanks
Kevin
Quoted 184 lines
From: Chia-I Wu <[email protected]>
Sent: Friday, February 21, 2020 12:51 PM(resend because gmail did not format to plain text...)
Quoted 9 lines · Chia-I Wu
Quoted 5 lines · Kevin
Quoted 5 lines
From: Chia-I Wu <[email protected]>
Sent: Friday, February 21, 2020 6:24 AMOn Wed, Feb 19, 2020 at 6:38 PM Tian, Kevin <[email protected]>
Quoted 8 lines · wrote:
Quoted 8 lines
Quoted 8 lines
Quoted 8 lines
Quoted 8 lines
From: Tian, Kevin
Sent: Thursday, February 20, 2020 10:05 AMQuoted 4 lines
From: Chia-I Wu <[email protected]>
Sent: Thursday, February 20, 2020 3:37 AMOn Wed, Feb 19, 2020 at 1:52 AM Tian, Kevin
Quoted 7 lines
Quoted 7 lines
Quoted 7 lines
Quoted 6 lines · wrote:
Quoted 6 lines
Quoted 6 lines
Quoted 6 lines
Quoted 6 lines
From: Paolo Bonzini
Sent: Wednesday, February 19, 2020 12:29 AMQuoted 1 line · Sean Christopherson
Quoted 1 line
On Fri, Feb 14, 2020 at 1:47 PM Chia-I Wu
Quoted 2 lines
Quoted 2 lines
Quoted 2 lines
Quoted 2 lines
Quoted 2 lines
Quoted 1 line · wrote:
Quoted 1 line
Quoted 1 line
Quoted 1 line
Quoted 1 line
Quoted 1 line
AFAICT, it is currently allowed on ARM (verified) and AMD
(not
Quoted 5 lines
Quoted 5 lines
Quoted 5 lines
Quoted 1 line
Quoted 1 line
Quoted 1 line
Quoted 1 line
Quoted 1 line
Quoted 1 line
Quoted 1 line
Quoted 1 line
verified, but
svm_get_mt_maskreturns 0 which supposedlymeans
Quoted 3 lines
Quoted 3 lines
Quoted 3 lines
the
Quoted 2 lines
Quoted 2 lines
NPT
Quoted 1 line
Quoted 1 line
Quoted 1 line
does not restrict what the guest PAT can do). This diff
would do
Quoted 3 lines
Quoted 3 lines
Quoted 3 lines
the
Quoted 2 lines
Quoted 2 lines
Quoted 2 lines
Quoted 2 lines
Quoted 2 lines
Quoted 2 lines
Quoted 2 lines
Quoted 1 line
trick for Intel without needing any uapi change:
I would be concerned about Intel CPU errata such as SKX40
and
Quoted 2 lines
Quoted 2 lines
Quoted 2 lines
Quoted 2 lines
Quoted 2 lines
SKX59.
Quoted 1 line
Quoted 1 line
Quoted 1 line
Quoted 1 line
The part KVM cares about, #MC, is already addressed by
forcing
Quoted 4 lines
Quoted 4 lines
Quoted 4 lines
UC
Quoted 3 lines
Quoted 3 lines
for
Quoted 2 lines
Quoted 2 lines
Quoted 2 lines
MMIO.
Quoted 1 line
The data corruption issue is on the guest kernel to correctly
use
Quoted 7 lines
Quoted 7 lines
Quoted 7 lines
WC
Quoted 3 lines
Quoted 3 lines
Quoted 3 lines
Quoted 3 lines
Quoted 3 lines
Quoted 1 line
and/or non-temporal writes.
What about coherency across live migration? The userspace
process
Quoted 2 lines
Quoted 2 lines
Quoted 2 lines
would
Quoted 1 line
Quoted 1 line
use cached accesses, and also a WBINVD could potentially
corrupt
Quoted 5 lines
Quoted 5 lines
Quoted 5 lines
guest
Quoted 4 lines
Quoted 4 lines
Quoted 4 lines
Quoted 4 lines
Quoted 2 lines
memory.
In such case the userspace process possibly should conservatively
use
Quoted 3 lines
Quoted 3 lines
Quoted 3 lines
Quoted 1 line
Quoted 1 line
Quoted 1 line
Quoted 1 line
UC mapping, as if for MMIO regions on a passthrough device.
However
Quoted 1 line
Quoted 1 line
Quoted 1 line
Quoted 1 line
there remains a problem. the definition of
KVM_MEM_DMAimplies
Quoted 1 line
Quoted 1 line
Quoted 1 line
Quoted 1 line
Quoted 1 line
Quoted 1 line
Quoted 1 line
favoring guest setting, which could be whatever type in concept.
Then
Quoted 3 lines
Quoted 3 lines
Quoted 3 lines
Quoted 1 line
Quoted 1 line
Quoted 1 line
Quoted 1 line
assuming UC is also problematic. I'm not sure whether inventing
another
Quoted 1 line
Quoted 1 line
Quoted 1 line
Quoted 1 line
interface to query effective memory type from KVM is a good
idea.
Quoted 2 lines
Quoted 2 lines
Quoted 2 lines
There
Quoted 1 line
Quoted 1 line
Quoted 1 line
Quoted 1 line
is no guarantee that the guest will use same type for every page
in the
Quoted 1 line
Quoted 1 line
Quoted 1 line
Quoted 1 line
Quoted 1 line
Quoted 1 line
Quoted 1 line
same slot, then such interface might be messy. Alternatively,
maybe
Quoted 1 line
Quoted 1 line
Quoted 1 line
Quoted 1 line
Quoted 1 line
Quoted 1 line
Quoted 1 line
we could just have an interface for KVM userspace to force
memory
Quoted 2 lines
Quoted 2 lines
Quoted 2 lines
type
Quoted 1 line
Quoted 1 line
Quoted 1 line
Quoted 1 line
for a given slot, if it is mainly used in para-virtualized scenarios
(e.g.
Quoted 1 line
Quoted 1 line
Quoted 1 line
Quoted 1 line
Quoted 1 line
Quoted 1 line
Quoted 1 line
virtio-gpu) where the guest is enlightened to use a forced type
(e.g.
Quoted 2 lines
Quoted 2 lines
Quoted 2 lines
WC)?
Quoted 1 line
Quoted 1 line
Quoted 1 line
KVM forcing the memory type for a given slot should work too. But
the
Quoted 2 lines
Quoted 2 lines
Quoted 2 lines
Quoted 2 lines
Quoted 2 lines
Quoted 2 lines
ignore-guest-pat bit seems to be Intel-specific. We will need to define how the second-level page attributes combine with the
guest
Quoted 4 lines
Quoted 4 lines
Quoted 4 lines
Quoted 4 lines
Quoted 4 lines
Quoted 1 line
page attributes somehow.
oh, I'm not aware of that difference. without an ipat-equivalent capability, I'm not sure how to forcing random type here. If you look
at
Quoted 1 line
Quoted 1 line
Quoted 1 line
Quoted 1 line
Quoted 1 line
table 11-7 in Intel SDM, none of MTRR (EPT) memory type can lead
to
Quoted 6 lines
Quoted 6 lines
Quoted 6 lines
Quoted 6 lines
Quoted 6 lines
consistent effective type when combining with random PAT value. So
it is definitely a dead end.Quoted 3 lines
KVM should in theory be able to tell that the userspace region is mapped with a certain memory type and can force the same
memory
Quoted 2 lines
Quoted 2 lines
Quoted 2 lines
type
Quoted 1 line
Quoted 1 line
Quoted 1 line
onto the guest. The userspace does not need to be involved. But
that
Quoted 1 line
Quoted 1 line
Quoted 1 line
Quoted 1 line
Quoted 1 line
Quoted 1 line
sounds very slow? This may be a dumb question, but would it help
to
Quoted 1 line
Quoted 1 line
Quoted 1 line
Quoted 1 line
Quoted 1 line
Quoted 1 line
add
KVM_SET_DMA_BUFand let KVM negotiate the memory typewith
Quoted 6 lines
Quoted 6 lines
Quoted 6 lines
the
Quoted 5 lines
Quoted 5 lines
Quoted 3 lines
in-kernel GPU drivers?
KVM_SET_DMA_BUFlooks more reasonable. But I guess we don'tneed
Quoted 2 lines
Quoted 2 lines
Quoted 2 lines
Quoted 2 lines
Quoted 2 lines
KVM to be aware of such negotiation. We can continue your original proposal to have KVM simply favor guest memory type (maybe still
call
Quoted 1 line
Quoted 1 line
Quoted 1 line
Quoted 1 line
Quoted 1 line
KVM_MEM_DMA). On the other hand, Qemu should just mmap onthe
Quoted 1 line
Quoted 1 line
Quoted 1 line
Quoted 1 line
Quoted 1 line
fd handle of the dmabuf passed from the virtio-gpu device backend,
e.g.
Quoted 12 lines
Quoted 12 lines
Quoted 12 lines
Quoted 2 lines
Quoted 2 lines
to conduct migration. That way the mmap request is finally served by DRM and underlying GPU drivers, with proper type enforced
automatically.
Quoted 9 lines
Quoted 1 line
Thinking more possibly we don't need introduce new interface to KVM. As long as Qemu uses dmabuf interface to mmap the specific region, KVM can simply check memory type in host page table given hva of a memslot. If the type is UC or WC, it implies that userspace wants a non-coherent mapping which should be reflected in the guest side too. In such case, KVM can go to non-cohenrent DMA path and favor guest memory type automatically.
Quoted 6 lines
Quoted 6 lines
Quoted 6 lines
Sorry, I mixed two things together.
Userspace access to dmabuf mmap must be guarded by DMA_BUF_SYNC_{START,END} ioctls. It is possible that the GPU driver always picks a WB mapping and let the ioctls flush/invalidate CPU caches. We actually want the guest memory type to match
vkMapMemory's
Quoted 1 line
Quoted 1 line
Quoted 1 line
memory type, which can be different from dmabuf mmap's memory
type.
Quoted 12 lines
Quoted 11 lines
Quoted 1 line
It is not enough for KVM to inspect the hva's memory type.
I'm not familiar with dmabuf and what is the difference between vkMapMemory and mmap. Just a simple thought that whatever memory type/synchronization enforced on the host userspace should ideally be applied to guest userspace too. e.g. in above example we possibly want the guest to use WB and issue flush/invalidate hypercalls to guard with other potential parallel operations in the host side. otherwise I cannot see how synchronization can be done when one use WB with sync primitives while the other simply use WC w/o such primitives.
I am reasonably familiar with the GPU stacks, but I am not familiar with KVM :)
When allocating a GPU memory, the userspace can specify whether it wants a
coherent one or an incoherent one. vkMapMemory returns a coherent or a incoherent mapping respectively. Indeed we also want the guest userspace to
have a coherent or a incoherent mapping respectively.The GPU memory can be exported as a dmabuf to share with another device or
process. For security, we allocate the GPU memory in a GPU process and we export the dmabuf to the hypervisor. mmap of dmabuf semantically returns an
incoherent mapping. As a result, the guest will set up a mapping that has the same memory type as the vkMapMemory mapping does, but the hva inKVM_SET_USER_MEMORY_REGIONpoints to the dmabuf's incoherent mapping.
Quoted 7 lines
If you think it is the best for KVM to inspect hva to determine the memory type with page granularity, that is reasonable and should work for us too. The userspace can do something (e.g., add a GPU driver dependency to the hypervisor such that the dma-buf is imported as a GPU memory and mapped using
vkMapMemory) or I can work with dma-buf maintainers to see if dma-buf's semantics can be changed.
I think you need consider the live migration requirement as Paolo pointed out. The migration thread needs to read/write the region, then it must use the same type as GPU process and guest to read/write the region. In such case, the hva mapped by Qemu should have the desired type as the guest. However, adding GPU driver dependency to Qemu might trigger some concern. I'm not sure whether there is generic mechanism though, to share dmabuf fd between GPU process and Qemu while allowing Qemu to follow the desired type w/o using vkMapMemory...
Note this is orthogonal to whether introducing a new uapi or implicitly checking hva to favor guest memory type. It's purely about Qemu itself. Ideally anyone with the desire to access a dma-buf object should follow the expected semantics. It's interesting that dma-buf sub-system doesn't provide a centralized synchronization about memory type between multiple mmap paths.
Quoted 26 lines
Quoted 7 lines
Quoted 7 lines
Quoted 7 lines
KVM_SET_DMA_BUF, if supported, is a signal to KVM that the guest memory type should be honored (or forced if there is a new op indma_buf_opsthat tells KVM which memory type to force).
KVM_MEM_DMAQuoted 18 lines
Quoted 18 lines
Quoted 3 lines
flag in this RFC sends the same signal. Unless
KVM_SET_DMA_BUFgives the userspace other features such as setting unlimited number of dmabufs to subregions of a memslot, it is not very useful.the good part of a new interface is its simplicity, but only in slot granularity. instead having KVM to inspect hva can support page granularity, but adding run-time overhead. Let's see how Paolo thinks.
Quoted 4 lines
If uapi change is to be avoided, it is the easiest that guest memory type is always honored unless it causes #MC (i.e.,is_mmio==true).
I feel this goes too far...
Thanks
Kevin
Quoted 10 lines · Kevin
Quoted 9 lines
From: Chia-I Wu <[email protected]>
Sent: Friday, February 21, 2020 12:51 PM
If you think it is the best for KVM to inspect hva to determine the memory type with page granularity, that is reasonable and should work for us too. The userspace can do something (e.g., add a GPU driver dependency to the hypervisor such that the dma-buf is imported as a GPU memory and mapped using
vkMapMemory) or I can work with dma-buf maintainers to see if dma-buf's semantics can be changed.
Quoted 8 lines
I think you need consider the live migration requirement as Paolo pointed out. The migration thread needs to read/write the region, then it must use the same type as GPU process and guest to read/write the region. In such case, the hva mapped by Qemu should have the desired type as the guest. However, adding GPU driver dependency to Qemu might trigger some concern. I'm not sure whether there is generic mechanism though, to share dmabuf fd between GPU process and Qemu while allowing Qemu to follow the desired type w/o using vkMapMemory...
Alternatively, KVM could make KVM_MEM_DMA and KVM_MEM_LOG_DIRTY_PAGES mutually exclusive, i.e. force a transition to WB memtype for the guest (with appropriate zapping) when migration is activated. I think that would work?
Quoted 5 lines
Note this is orthogonal to whether introducing a new uapi or implicitly checking hva to favor guest memory type. It's purely about Qemu itself. Ideally anyone with the desire to access a dma-buf object should follow the expected semantics. It's interesting that dma-buf sub-system doesn't provide a centralized synchronization about memory type between multiple mmap paths.
Quoted 21 lines · Sean Christopherson
Quoted 10 lines · Kevin
Quoted 9 lines
From: Chia-I Wu <[email protected]>
Sent: Friday, February 21, 2020 12:51 PM
If you think it is the best for KVM to inspect hva to determine the memory type with page granularity, that is reasonable and should work for us too. The userspace can do something (e.g., add a GPU driver dependency to the hypervisor such that the dma-buf is imported as a GPU memory and mapped using
vkMapMemory) or I can work with dma-buf maintainers to see if dma-buf's semantics can be changed.Quoted 8 lines
I think you need consider the live migration requirement as Paolo pointed out. The migration thread needs to read/write the region, then it must use the same type as GPU process and guest to read/write the region. In such case, the hva mapped by Qemu should have the desired type as the guest. However, adding GPU driver dependency to Qemu might trigger some concern. I'm not sure whether there is generic mechanism though, to share dmabuf fd between GPU process and Qemu while allowing Qemu to follow the desired type w/o using vkMapMemory...
Quoted 4 lines
Alternatively, KVM could make
KVM_MEM_DMAandKVM_MEM_LOG_DIRTY_PAGESmutually exclusive, i.e. force a transition to WB memtype for the guest (with appropriate zapping) when migration is activated. I think that would work?
Hm, virtio-gpu does not allow live migration when the 3D function (virgl=on) is enabled. This is the relevant code in qemu:
if (virtio_gpu_virgl_enabled(g->conf)) {
error_setg(&g->migration_blocker, "virgl is not yet migratable");Although we (virtio-gpu and virglrenderer projects) plan to make host GPU buffers available to the guest via memslots, those buffers should be considered a part of the "GPU state". The migration thread should work with virglrenderer and let virglrenderer save/restore them, if live migration is to be supported.
QEMU depends on GPU drivers already when configured with --enable-virglrenderer. There is vhost-user-gpu that can move the dependency to a GPU process. But there are still going to be cases (e.g., nVidia's proprietary driver does not support dma-buf) where QEMU cannot avoid GPU driver dependency.
Quoted 5 lines
Quoted 5 lines
Note this is orthogonal to whether introducing a new uapi or implicitly checking hva to favor guest memory type. It's purely about Qemu itself. Ideally anyone with the desire to access a dma-buf object should follow the expected semantics. It's interesting that dma-buf sub-system doesn't provide a centralized synchronization about memory type between multiple mmap paths.
Quoted 45 lines
From: Chia-I Wu <[email protected]>
Sent: Saturday, February 22, 2020 2:21 AMQuoted 5 lines · Sean Christopherson
Quoted 3 lines · Kevin
Quoted 3 lines
From: Chia-I Wu <[email protected]>
Sent: Friday, February 21, 2020 12:51 PM
If you think it is the best for KVM to inspect hva to determine thememory
Quoted 1 line
Quoted 1 line
Quoted 1 line
type with page granularity, that is reasonable and should work for us
too.
Quoted 1 line
Quoted 1 line
Quoted 1 line
The userspace can do something (e.g., add a GPU driver dependency to
the
Quoted 1 line
Quoted 1 line
Quoted 1 line
hypervisor such that the dma-buf is imported as a GPU memory and
mapped
Quoted 2 lines
Quoted 2 lines
Quoted 2 lines
using
vkMapMemory) or I can work with dma-buf maintainers to see if dma-buf's
Quoted 3 lines
Quoted 3 lines
Quoted 1 line
semantics can be changed.
I think you need consider the live migration requirement as Paolo pointed
out.
Quoted 2 lines
Quoted 2 lines
The migration thread needs to read/write the region, then it must use the same type as GPU process and guest to read/write the region. In such
case,
Quoted 1 line
Quoted 1 line
the hva mapped by Qemu should have the desired type as the guest.
However,
Quoted 1 line
Quoted 1 line
adding GPU driver dependency to Qemu might trigger some concern. I'm
not
Quoted 1 line
Quoted 1 line
sure whether there is generic mechanism though, to share dmabuf fd
between GPU
Quoted 1 line
Quoted 1 line
process and Qemu while allowing Qemu to follow the desired type w/o
using
Quoted 3 lines
Quoted 1 line
vkMapMemory...
Alternatively, KVM could make
KVM_MEM_DMAand
KVM_MEM_LOG_DIRTY_PAGESQuoted 3 lines
mutually exclusive, i.e. force a transition to WB memtype for the guest (with appropriate zapping) when migration is activated. I think that would work?
Hm, virtio-gpu does not allow live migration when the 3D function (virgl=on) is enabled. This is the relevant code in qemu:
Quoted 8 lines
if (virtio_gpu_virgl_enabled(g->conf)) { error_setg(&g->migration_blocker, "virgl is not yet migratable");Although we (virtio-gpu and virglrenderer projects) plan to make host GPU buffers available to the guest via memslots, those buffers should be considered a part of the "GPU state". The migration thread should work with virglrenderer and let virglrenderer save/restore them, if live migration is to be supported.
Thanks for your explanation. Your RFC makes more sense now.
One remaining open is, although for live migration we can explicitly state that migration thread itself should not access the dma-buf region, how can we warn other usages which may potentially simply walk every memslot and access the content through the mmap-ed virtual address? Possibly we may need a flag to indicate a memslot which is mmaped only for KVM to retrieve its page table mapping but not for direct access in Qemu.
Quoted 18 lines
QEMU depends on GPU drivers already when configured with --enable-virglrenderer. There is vhost-user-gpu that can move the dependency to a GPU process. But there are still going to be cases (e.g., nVidia's proprietary driver does not support dma-buf) where QEMU cannot avoid GPU driver dependency.
Quoted 1 line
Quoted 1 line
Note this is orthogonal to whether introducing a new uapi or implicitly
checking
Quoted 1 line
Quoted 1 line
hva to favor guest memory type. It's purely about Qemu itself. Ideally
anyone
Quoted 1 line
Quoted 1 line
with the desire to access a dma-buf object should follow the expected
semantics.
Quoted 2 lines
Quoted 2 lines
It's interesting that dma-buf sub-system doesn't provide a centralized synchronization about memory type between multiple mmap paths.
Quoted 42 lines · Paolo Bonzini
Quoted 4 lines · Chia-I Wu
The bug you mentioned was probably this one
Yes, indeed.
Quoted 6 lines
From what I can tell, the commit allowed the guests to create cached mappings to MMIO regions and caused MCEs. That is different than what I need, which is to allow guests to create uncached mappings to system ram (i.e., !kvm_is_mmio_pfn) when the host userspace also has uncached mappings. But it is true that this still allows the userspace & guest kernel to create conflicting memory types.
Right, the question is whether the MCEs were tied to MMIO regions specifically and if so why.
An interesting remark is in the footnote of table 11-7 in the SDM. There, for the MTRR (EPT for us) memory type UC you can read:
The UC attribute comes from the MTRRs and the processors are not required to snoop their caches since the data could never have been cached. This attribute is preferred for performance reasons.
There are two possibilities:
1) the footnote doesn't apply to UC mode coming from EPT page tables. That would make your change safe.
2) the footnote also applies when the UC attribute comes from the EPT page tables rather than the MTRRs. In that case, the host should use UC as the EPT page attribute if and only if it's consistent with the host MTRRs; it would be more or less impossible to honor UC in the guest MTRRs. In that case, something like the patch below would be needed.
It is not clear from the manual why the footnote would not apply to WC; that is, the manual doesn't say explicitly that the processor does not do snooping for accesses to WC memory. But I guess that must be the case, which is why I used
MTRR_TYPE_WRCOMBin the patch below.
Quoted 6 lines
Either way, we would have an explanation of why creating cached mapping to MMIO regions would, and why in practice we're not seeing MCEs for guest RAM (the guest would have set WB for that memory in its MTRRs, not UC).
One thing you didn't say: how would userspace use
KVM_MEM_DMA? On which regions would it be set?
It will be set for shmems that are mapped WC.
GPU/DRM drivers allocate shmems as DMA-able gpu buffers and allow the userspace to map them cached or WC (I915_MMAP_WC or AMDGPU_GEM_CREATE_CPU_GTT_USWC for example). When a shmem is mapped WC and is made available to the guest, we would like the ability to map the region WC in the guest.
Quoted 17 lines
Thanks,
Paolo
arch/x86/kvm/vmx/vmx.c +2
-1@@ -6920,8 +6920,16 @@ static u64 vmx_get_mt_mask(struct kvm_vcpu *vcpu, gfn_t gfn, bool is_mmio) } cache =kvm_mtrr_get_guest_memory_type (vcpu, gfn); - exit: +if (cache ==MTRR_TYPE_UNCACHABLE && !is_mmio) { +/*
arch/x86/kvm/vmx/vmx.c static u64 vmx_get_mt_mask(struct kvm_vcpu *vcpu, gfn_t gfn, bool is_mmio) · line 6935
Quoted 10 lines
arch/x86/kvm/vmx/vmx.c +7
-0+* We cannot set UC in the EPT page tables as it can cause +* machine check exceptions (??). Hopefully the guest is +* using PAT. +*/ + cache =MTRR_TYPE_WRCOMB ; + } +return (cache <<VMX_EPT_MT_EPTE_SHIFT ) | ipat; }
_______________________________________________
dri-devel mailing list
[email protected]
https://lists.freedesktop.org/mailman/listinfo/dri-devel
Quoted 60 lines
From: Chia-I Wu
Sent: Saturday, February 15, 2020 5:15 AMQuoted 13 lines · Paolo Bonzini
Quoted 4 lines · Chia-I Wu
The bug you mentioned was probably this one
Yes, indeed.
Quoted 4 lines
From what I can tell, the commit allowed the guests to create cached mappings to MMIO regions and caused MCEs. That is different than what I need, which is to allow guests to create uncached mappings to system ram (i.e., !kvm_is_mmio_pfn) when the host userspace also has
uncached
Quoted 15 lines
Quoted 2 lines
mappings. But it is true that this still allows the userspace & guest kernel to create conflicting memory types.
Right, the question is whether the MCEs were tied to MMIO regions specifically and if so why.
An interesting remark is in the footnote of table 11-7 in the SDM. There, for the MTRR (EPT for us) memory type UC you can read:
The UC attribute comes from the MTRRs and the processors are not required to snoop their caches since the data could never have been cached. This attribute is preferred for performance reasons.
There are two possibilities:
Quoted 7 lines
1) the footnote doesn't apply to UC mode coming from EPT page tables. That would make your change safe.
2) the footnote also applies when the UC attribute comes from the EPT page tables rather than the MTRRs. In that case, the host should use UC as the EPT page attribute if and only if it's consistent with the host MTRRs; it would be more or less impossible to honor UC in the guest
MTRRs.
Quoted 3 lines
In that case, something like the patch below would be needed.
It is not clear from the manual why the footnote would not apply to WC;
that
Quoted 1 line
is, the manual doesn't say explicitly that the processor does not do
snooping
Quoted 1 line
for accesses to WC memory. But I guess that must be the case, which is
why I
Quoted 3 lines
used
MTRR_TYPE_WRCOMBin the patch below.Either way, we would have an explanation of why creating cached mapping
to
Quoted 1 line
MMIO regions would, and why in practice we're not seeing MCEs for guest
RAM
Quoted 3 lines
(the guest would have set WB for that memory in its MTRRs, not UC).
One thing you didn't say: how would userspace use
KVM_MEM_DMA? Onwhich
Quoted 1 line
regions would it be set?
Quoted 8 lines
It will be set for shmems that are mapped WC.
GPU/DRM drivers allocate shmems as DMA-able gpu buffers and allow the userspace to map them cached or WC (
I915_MMAP_WCorAMDGPU_GEM_CREATE_CPU_GTT_USWCfor example). When a shmem is mapped
WC and is made available to the guest, we would like the ability to map the region WC in the guest.
Curious... How is such slot exposed to the guest? A reserved memory region? Is it static or might be dynamically added?
Thanks
Kevin
_______________________________________________
dri-devel mailing list
[email protected]
https://lists.freedesktop.org/mailman/listinfo/dri-devel
Quoted 70 lines · Kevin
Quoted 61 lines
From: Chia-I Wu
Sent: Saturday, February 15, 2020 5:15 AMQuoted 13 lines · Paolo Bonzini
Quoted 4 lines · Chia-I Wu
The bug you mentioned was probably this one
Yes, indeed.
Quoted 4 lines
From what I can tell, the commit allowed the guests to create cached mappings to MMIO regions and caused MCEs. That is different than what I need, which is to allow guests to create uncached mappings to system ram (i.e., !kvm_is_mmio_pfn) when the host userspace also has
uncached
Quoted 15 lines
Quoted 2 lines
mappings. But it is true that this still allows the userspace & guest kernel to create conflicting memory types.
Right, the question is whether the MCEs were tied to MMIO regions specifically and if so why.
An interesting remark is in the footnote of table 11-7 in the SDM. There, for the MTRR (EPT for us) memory type UC you can read:
The UC attribute comes from the MTRRs and the processors are not required to snoop their caches since the data could never have been cached. This attribute is preferred for performance reasons.
There are two possibilities:
Quoted 7 lines
1) the footnote doesn't apply to UC mode coming from EPT page tables. That would make your change safe.
2) the footnote also applies when the UC attribute comes from the EPT page tables rather than the MTRRs. In that case, the host should use UC as the EPT page attribute if and only if it's consistent with the host MTRRs; it would be more or less impossible to honor UC in the guest
MTRRs.
Quoted 3 lines
In that case, something like the patch below would be needed.
It is not clear from the manual why the footnote would not apply to WC;
that
Quoted 1 line
is, the manual doesn't say explicitly that the processor does not do
snooping
Quoted 1 line
for accesses to WC memory. But I guess that must be the case, which is
why I
Quoted 3 lines
used
MTRR_TYPE_WRCOMBin the patch below.Either way, we would have an explanation of why creating cached mapping
to
Quoted 1 line
MMIO regions would, and why in practice we're not seeing MCEs for guest
RAM
Quoted 3 lines
(the guest would have set WB for that memory in its MTRRs, not UC).
One thing you didn't say: how would userspace use
KVM_MEM_DMA? Onwhich
Quoted 1 line
regions would it be set?
Quoted 8 lines
It will be set for shmems that are mapped WC.
GPU/DRM drivers allocate shmems as DMA-able gpu buffers and allow the userspace to map them cached or WC (
I915_MMAP_WCorAMDGPU_GEM_CREATE_CPU_GTT_USWCfor example). When a shmem is mapped
WC and is made available to the guest, we would like the ability to map the region WC in the guest.
Quoted 2 lines
Curious... How is such slot exposed to the guest? A reserved memory region? Is it static or might be dynamically added?
The plan is for virtio-gpu device to reserve a huge memory region in the guest. Memslots may be added dynamically or statically to back the region.
Dynamic: the host adds a 16MB GPU allocation as a memslot at a time. The guest kernel suballocates from the 16MB pool.
Static: the host creates a huge PROT_NONE memfd and adds it as a memslot. GPU allocations are mremap()ed into the memfd region to provide the real mapping.
These options are considered because the number of memslots are
limited: 32 on ARM and 509 on x86. If the number of memslots could be made larger (4096 or more), we would also consider adding each individual GPU allocation as a memslot.
These are actually questions we need feedback. Besides, GPU allocations can be assumed to be kernel dma-bufs in this context. I wonder if it makes sense to have a variation of KVM_SET_USER_MEMORY_REGION that takes dma-bufs.
Quoted 3 lines
Thanks
Kevin
Quoted 82 lines
From: Chia-I Wu <[email protected]>
Sent: Thursday, February 20, 2020 3:18 AMQuoted 5 lines · Kevin
Quoted 5 lines
From: Chia-I Wu
Sent: Saturday, February 15, 2020 5:15 AMOn Fri, Feb 14, 2020 at 2:26 AM Paolo Bonzini <[email protected]>
Quoted 11 lines · wrote:
Quoted 11 lines
Quoted 11 lines · Chia-I Wu
Quoted 4 lines
The bug you mentioned was probably this one
Yes, indeed.
Quoted 2 lines
From what I can tell, the commit allowed the guests to create cached mappings to MMIO regions and caused MCEs. That is different than
what
Quoted 1 line
Quoted 1 line
Quoted 1 line
Quoted 1 line
I need, which is to allow guests to create uncached mappings to
system
Quoted 28 lines
Quoted 28 lines
Quoted 1 line
Quoted 1 line
ram (i.e., !kvm_is_mmio_pfn) when the host userspace also has
uncached
Quoted 15 lines
Quoted 2 lines
mappings. But it is true that this still allows the userspace & guest kernel to create conflicting memory types.
Right, the question is whether the MCEs were tied to MMIO regions specifically and if so why.
An interesting remark is in the footnote of table 11-7 in the SDM. There, for the MTRR (EPT for us) memory type UC you can read:
The UC attribute comes from the MTRRs and the processors are not required to snoop their caches since the data could never have been cached. This attribute is preferred for performance reasons.
There are two possibilities:
Quoted 7 lines
1) the footnote doesn't apply to UC mode coming from EPT page tables. That would make your change safe.
2) the footnote also applies when the UC attribute comes from the EPT page tables rather than the MTRRs. In that case, the host should use UC as the EPT page attribute if and only if it's consistent with the host MTRRs; it would be more or less impossible to honor UC in the guest
MTRRs.
Quoted 3 lines
In that case, something like the patch below would be needed.
It is not clear from the manual why the footnote would not apply to WC;
Quoted 8 lines
Quoted 8 lines
that
Quoted 1 line
is, the manual doesn't say explicitly that the processor does not do
snooping
Quoted 1 line
for accesses to WC memory. But I guess that must be the case, which is
why I
Quoted 3 lines
used
MTRR_TYPE_WRCOMBin the patch below.Either way, we would have an explanation of why creating cached
mapping
Quoted 2 lines
Quoted 2 lines
to
Quoted 1 line
MMIO regions would, and why in practice we're not seeing MCEs for
guest
Quoted 4 lines
Quoted 4 lines
RAM
Quoted 3 lines
(the guest would have set WB for that memory in its MTRRs, not UC).
One thing you didn't say: how would userspace use
KVM_MEM_DMA?On
Quoted 5 lines
Quoted 5 lines
which
Quoted 1 line
regions would it be set?
It will be set for shmems that are mapped WC.
GPU/DRM drivers allocate shmems as DMA-able gpu buffers and allow
the
Quoted 2 lines
Quoted 2 lines
userspace to map them cached or WC (
I915_MMAP_WCorAMDGPU_GEM_CREATE_CPU_GTT_USWCfor example). When a shmemis
Quoted 4 lines
Quoted 3 lines
mapped
WC and is made available to the guest, we would like the ability to map the region WC in the guest.
Quoted 5 lines
Quoted 2 lines
Curious... How is such slot exposed to the guest? A reserved memory region? Is it static or might be dynamically added?
The plan is for virtio-gpu device to reserve a huge memory region in the guest. Memslots may be added dynamically or statically to back the region.
so the region is marked as E820_RESERVED to prevent guest kernel from using it for other purpose and then virtio-gpu device will report virtio-gpu driver of the exact location of the region through its own interface?
Quoted 13 lines
Dynamic: the host adds a 16MB GPU allocation as a memslot at a time. The guest kernel suballocates from the 16MB pool.
Static: the host creates a huge
PROT_NONEmemfd and adds it as a memslot. GPU allocations are mremap()ed into the memfd region to provide the real mapping.These options are considered because the number of memslots are
limited: 32 on ARM and 509 on x86. If the number of memslots could be made larger (4096 or more), we would also consider adding each individual GPU allocation as a memslot.
Quoted 4 lines
These are actually questions we need feedback. Besides, GPU allocations can be assumed to be kernel dma-bufs in this context. I wonder if it makes sense to have a variation of
KVM_SET_USER_MEMORY_REGIONthat takes dma-bufs.
I feel it makes more sense.
Thanks
Kevin
_______________________________________________
dri-devel mailing list
[email protected]
https://lists.freedesktop.org/mailman/listinfo/dri-devel
Quoted 10 lines · Kevin
Quoted 5 lines
Quoted 2 lines
Curious... How is such slot exposed to the guest? A reserved memory region? Is it static or might be dynamically added?
The plan is for virtio-gpu device to reserve a huge memory region in the guest. Memslots may be added dynamically or statically to back the region.
so the region is marked as
E820_RESERVEDto prevent guest kernel from using it for other purpose and then virtio-gpu device will report virtio-gpu driver of the exact location of the region through its own interface?
The current plan is that the virtio-gpu device will have a bar for the region, which is like the vram aperture on real GPUs. The virtio-gpu driver manages the region like managing vram.
When the guest userspace allocates from vram, the guest kernel reserves an unused range from the region and tells the host the offset. The host allocates a real GPU buffer, maps the buffer, and add a memslot with gpa==bar_base+offset (or mremap). When the guest userspace mmap, the guest kernel does a io_remap_pfn_range.
_______________________________________________
dri-devel mailing list
[email protected]
https://lists.freedesktop.org/mailman/listinfo/dri-devel
Hi,
Quoted 8 lines
Quoted 3 lines
The plan is for virtio-gpu device to reserve a huge memory region in the guest. Memslots may be added dynamically or statically to back the region.
so the region is marked as
E820_RESERVEDto prevent guest kernel from using it for other purpose and then virtio-gpu device will report virtio-gpu driver of the exact location of the region through its own interface?
It's large pci bar, to reserve address space, using (recently added) virtio shared memory support. dma-bufs are mapped dynamically as sub-regions into that pci bar.
At kvm level that'll end up as one memory slot per dma-buf.
cheers,
Gerd