arm64: dts: qcom: sc7180: Add nodes for eMMC and SD card
Subsystems (5)
Device tree bindings Arm Qualcomm mailing list MMC, SD and SDIO Arm Qualcomm support +1 more subsystems
PATCH v3 1/1 arm64: dts: qcom: sc7180: Add nodes for eMMC and SD card
From: Veerabhadrarao Badiganti <[email protected]>
Add sdhc instances for supporting eMMC and SD-card on sc7180. The regulators should be in HPM state for proper functionality of eMMC and SD-card. Updating corresponding regulators accordingly.
Signed-off-by Veerabhadrarao Badiganti <[email protected]>
Signed-off-by Shaik Sajida Bhanu <[email protected]>
---
Changes since V2:
- Added cmdq register space and support-cqe flag.
- Incorporated review comments by Matthias Kaehlcke.
Changes since V1:
- Updated the regulator min, max voltages as per eMMC/SD-card voltage requirements
- Enabled IOMMU for eMMC and SD-card.
- Added pull and drive strength to SD-card cd-gpio.
- Incorporated review comments by Matthias Kaehlcke.
--- arch/arm64/boot/dts/qcom/sc7180-idp.dts | 47 +++++++--- arch/arm64/boot/dts/qcom/sc7180.dtsi | 148 ++++++++++++++++++++++++++++++++ 2 files changed, 183 insertions(+), 12 deletions(-)
arch/arm64/boot/dts/qcom/sc7180-idp.dts +35 -12
@@ -7,6 +7,7 @@ /dts-v1/; +#include <dt-bindings/gpio/gpio.h> #include <dt-bindings/regulator/qcom,rpmh-regulator.h> #include "sc7180.dtsi" #include "pm6150.dtsi"
@@ -101,9 +102,9 @@ }; vreg_l12a_1p8: ldo12 { - regulator-min-microvolt = <1696000>; - regulator-max-microvolt = <1952000>; - regulator-initial-mode = <RPMH_REGULATOR_MODE_LPM>; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; }; vreg_l13a_1p8: ldo13 {
@@ -143,9 +144,9 @@ }; vreg_l19a_2p9: ldo19 { - regulator-min-microvolt = <2696000>; - regulator-max-microvolt = <3304000>; - regulator-initial-mode = <RPMH_REGULATOR_MODE_LPM>; + regulator-min-microvolt = <2960000>; + regulator-max-microvolt = <2960000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; }; };
@@ -189,9 +190,9 @@ }; vreg_l6c_2p9: ldo6 { - regulator-min-microvolt = <2696000>; - regulator-max-microvolt = <3304000>; - regulator-initial-mode = <RPMH_REGULATOR_MODE_LPM>; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <2950000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; }; vreg_l7c_3p0: ldo7 {
@@ -207,9 +208,9 @@ }; vreg_l9c_2p9: ldo9 { - regulator-min-microvolt = <2952000>; - regulator-max-microvolt = <3304000>; - regulator-initial-mode = <RPMH_REGULATOR_MODE_LPM>; + regulator-min-microvolt = <2960000>; + regulator-max-microvolt = <2960000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; }; vreg_l10c_3p3: ldo10 {
@@ -254,6 +255,28 @@ status = "okay"; }; +&sdhc_1 { + status = "okay"; + + pinctrl-names = "default", "sleep"; + pinctrl-0 = <&sdc1_on>; + pinctrl-1 = <&sdc1_off>; + vmmc-supply = <&vreg_l19a_2p9>; + vqmmc-supply = <&vreg_l12a_1p8>; +}; + +&sdhc_2 { + status = "okay"; + + pinctrl-names = "default","sleep"; + pinctrl-0 = <&sdc2_on>; + pinctrl-1 = <&sdc2_off>; + vmmc-supply = <&vreg_l9c_2p9>; + vqmmc-supply = <&vreg_l6c_2p9>; + + cd-gpios = <&tlmm 69 GPIO_ACTIVE_LOW>; +}; + &uart3 { status = "okay"; };
arch/arm64/boot/dts/qcom/sc7180.dtsi +148 -0
160 lines not on this page · raw message
Signature · 2 lines
QUALCOMM INDIA, on behalf of Qualcomm Innovation Center, Inc. is a member of Code Aurora Forum, hosted by The Linux Foundation
ping!
Quoted 283 lines · Shaik Sajida Bhanu
From: Veerabhadrarao Badiganti <[email protected]>
Add sdhc instances for supporting eMMC and SD-card on sc7180. The regulators should be in HPM state for proper functionality of eMMC and SD-card. Updating corresponding regulators accordingly.
Signed-off-by Veerabhadrarao Badiganti <[email protected]>Signed-off-by Shaik Sajida Bhanu <[email protected]>---
Changes since V2:
- Added cmdq register space and support-cqe flag.
- Incorporated review comments by Matthias Kaehlcke.Changes since V1:
- Updated the regulator min, max voltages as per eMMC/SD-card voltage requirements
- Enabled IOMMU for eMMC and SD-card.
- Added pull and drive strength to SD-card cd-gpio.
- Incorporated review comments by Matthias Kaehlcke.--- arch/arm64/boot/dts/qcom/sc7180-idp.dts | 47 +++++++--- arch/arm64/boot/dts/qcom/sc7180.dtsi | 148 ++++++++++++++++++++++++++++++++ 2 files changed, 183 insertions(+), 12 deletions(-)arch/arm64/boot/dts/qcom/sc7180-idp.dts +35
-12@@ -7,6 +7,7 @@ /dts-v1/; +#include <dt-bindings/gpio/gpio.h> #include <dt-bindings/regulator/qcom,rpmh-regulator.h> #include "sc7180.dtsi" #include "pm6150.dtsi"@@ -101,9 +102,9 @@ }; vreg_l12a_1p8: ldo12 { - regulator-min-microvolt = <1696000>; - regulator-max-microvolt = <1952000>; - regulator-initial-mode = <RPMH_REGULATOR_MODE_LPM>; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; }; vreg_l13a_1p8: ldo13 {@@ -143,9 +144,9 @@ }; vreg_l19a_2p9: ldo19 { - regulator-min-microvolt = <2696000>; - regulator-max-microvolt = <3304000>; - regulator-initial-mode = <RPMH_REGULATOR_MODE_LPM>; + regulator-min-microvolt = <2960000>; + regulator-max-microvolt = <2960000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; }; };@@ -189,9 +190,9 @@ }; vreg_l6c_2p9: ldo6 { - regulator-min-microvolt = <2696000>; - regulator-max-microvolt = <3304000>; - regulator-initial-mode = <RPMH_REGULATOR_MODE_LPM>; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <2950000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; }; vreg_l7c_3p0: ldo7 {@@ -207,9 +208,9 @@ }; vreg_l9c_2p9: ldo9 { - regulator-min-microvolt = <2952000>; - regulator-max-microvolt = <3304000>; - regulator-initial-mode = <RPMH_REGULATOR_MODE_LPM>; + regulator-min-microvolt = <2960000>; + regulator-max-microvolt = <2960000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; }; vreg_l10c_3p3: ldo10 {@@ -254,6 +255,28 @@ status = "okay"; }; +&sdhc_1 { + status = "okay"; + + pinctrl-names = "default", "sleep"; + pinctrl-0 = <&sdc1_on>; + pinctrl-1 = <&sdc1_off>; + vmmc-supply = <&vreg_l19a_2p9>; + vqmmc-supply = <&vreg_l12a_1p8>; +}; + +&sdhc_2 { + status = "okay"; + + pinctrl-names = "default","sleep"; + pinctrl-0 = <&sdc2_on>; + pinctrl-1 = <&sdc2_off>; + vmmc-supply = <&vreg_l9c_2p9>; + vqmmc-supply = <&vreg_l6c_2p9>; + + cd-gpios = <&tlmm 69 GPIO_ACTIVE_LOW>; +}; + &uart3 { status = "okay"; };arch/arm64/boot/dts/qcom/sc7180.dtsi +148
-0@@ -226,6 +226,33 @@ }; }; + sdhc_1: sdhci@7c4000 { + compatible = "qcom,sc7180-sdhci", "qcom,sdhci-msm-v5"; + reg = <0 0x7c4000 0 0x1000>, + <0 0x07c5000 0 0x1000>; + reg-names = "hc_mem", "cqhci_mem"; + + iommus = <&apps_smmu 0x60 0x0>; + interrupts = <GIC_SPI 641 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 644 IRQ_TYPE_LEVEL_HIGH>; + interrupt-names = "hc_irq", "pwr_irq"; + + clocks = <&gcc GCC_SDCC1_APPS_CLK>, + <&gcc GCC_SDCC1_AHB_CLK>; + clock-names = "core", "iface"; + + bus-width = <8>; + non-removable; + supports-cqe; + + mmc-ddr-1_8v; + mmc-hs200-1_8v; + mmc-hs400-1_8v; + mmc-hs400-enhanced-strobe; + + status = "disabled"; + }; + qupv3_id_0: geniqup@8c0000 { compatible = "qcom,geni-se-qup"; reg = <0 0x008c0000 0 0x6000>;@@ -929,6 +956,127 @@ function = "qup15"; }; }; + + sdc1_on: sdc1-on { + pinconf-clk { + pins = "sdc1_clk"; + bias-disable; + drive-strength = <16>; + }; + + pinconf-cmd { + pins = "sdc1_cmd"; + bias-pull-up; + drive-strength = <10>; + }; + + pinconf-data { + pins = "sdc1_data"; + bias-pull-up; + drive-strength = <10>; + }; + + pinconf-rclk { + pins = "sdc1_rclk"; + bias-pull-down; + }; + }; + + sdc1_off: sdc1-off { + pinconf-clk { + pins = "sdc1_clk"; + bias-disable; + drive-strength = <2>; + }; + + pinconf-cmd { + pins = "sdc1_cmd"; + bias-pull-up; + drive-strength = <2>; + }; + + pinconf-data { + pins = "sdc1_data"; + bias-pull-up; + drive-strength = <2>; + }; + + pinconf-rclk { + pins = "sdc1_rclk"; + bias-pull-down; + }; + }; + + sdc2_on: sdc2-on { + pinconf-clk { + pins = "sdc2_clk"; + bias-disable; + drive-strength = <16>; + }; + + pinconf-cmd { + pins = "sdc2_cmd"; + bias-pull-up; + drive-strength = <10>; + }; + + pinconf-data { + pins = "sdc2_data"; + bias-pull-up; + drive-strength = <10>; + }; + + pinconf-sd-cd { + pins = "gpio69"; + bias-pull-up; + drive-strength = <2>; + }; + }; + + sdc2_off: sdc2-off { + pinconf-clk { + pins = "sdc2_clk"; + bias-disable; + drive-strength = <2>; + }; + + pinconf-cmd { + pins = "sdc2_cmd"; + bias-pull-up; + drive-strength = <2>; + }; + + pinconf-data { + pins = "sdc2_data"; + bias-pull-up; + drive-strength = <2>; + }; + + pinconf-sd-cd { + pins = "gpio69"; + bias-disable; + drive-strength = <2>; + }; + }; + }; + + sdhc_2: sdhci@8804000 { + compatible = "qcom,sc7180-sdhci", "qcom,sdhci-msm-v5"; + reg = <0 0x08804000 0 0x1000>; + reg-names = "hc_mem"; + + iommus = <&apps_smmu 0x80 0>; + interrupts = <GIC_SPI 204 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 222 IRQ_TYPE_LEVEL_HIGH>; + interrupt-names = "hc_irq", "pwr_irq"; + + clocks = <&gcc GCC_SDCC2_APPS_CLK>, + <&gcc GCC_SDCC2_AHB_CLK>; + clock-names = "core", "iface"; + + bus-width = <4>; + + status = "disabled"; }; qspi: spi@88dc000 {
Quoted 3 lines · Veerabhadrarao Badiganti
ping!
I think you need to ping the SoC maintainers, this isn't something that I normally pick up via the mmc subsystem.
Kind regards
Uffe
Quoted 284 lines · Shaik Sajida Bhanu
Quoted 283 lines
From: Veerabhadrarao Badiganti <[email protected]>
Add sdhc instances for supporting eMMC and SD-card on sc7180. The regulators should be in HPM state for proper functionality of eMMC and SD-card. Updating corresponding regulators accordingly.
Signed-off-by Veerabhadrarao Badiganti <[email protected]>Signed-off-by Shaik Sajida Bhanu <[email protected]>---
Changes since V2:
- Added cmdq register space and support-cqe flag.
- Incorporated review comments by Matthias Kaehlcke.Changes since V1:
- Updated the regulator min, max voltages as per eMMC/SD-card voltage requirements
- Enabled IOMMU for eMMC and SD-card.
- Added pull and drive strength to SD-card cd-gpio.
- Incorporated review comments by Matthias Kaehlcke.--- arch/arm64/boot/dts/qcom/sc7180-idp.dts | 47 +++++++--- arch/arm64/boot/dts/qcom/sc7180.dtsi | 148 ++++++++++++++++++++++++++++++++ 2 files changed, 183 insertions(+), 12 deletions(-)arch/arm64/boot/dts/qcom/sc7180-idp.dts +35
-12@@ -7,6 +7,7 @@ /dts-v1/; +#include <dt-bindings/gpio/gpio.h> #include <dt-bindings/regulator/qcom,rpmh-regulator.h> #include "sc7180.dtsi" #include "pm6150.dtsi"@@ -101,9 +102,9 @@ }; vreg_l12a_1p8: ldo12 { - regulator-min-microvolt = <1696000>; - regulator-max-microvolt = <1952000>; - regulator-initial-mode = <RPMH_REGULATOR_MODE_LPM>; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; }; vreg_l13a_1p8: ldo13 {@@ -143,9 +144,9 @@ }; vreg_l19a_2p9: ldo19 { - regulator-min-microvolt = <2696000>; - regulator-max-microvolt = <3304000>; - regulator-initial-mode = <RPMH_REGULATOR_MODE_LPM>; + regulator-min-microvolt = <2960000>; + regulator-max-microvolt = <2960000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; }; };@@ -189,9 +190,9 @@ }; vreg_l6c_2p9: ldo6 { - regulator-min-microvolt = <2696000>; - regulator-max-microvolt = <3304000>; - regulator-initial-mode = <RPMH_REGULATOR_MODE_LPM>; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <2950000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; }; vreg_l7c_3p0: ldo7 {@@ -207,9 +208,9 @@ }; vreg_l9c_2p9: ldo9 { - regulator-min-microvolt = <2952000>; - regulator-max-microvolt = <3304000>; - regulator-initial-mode = <RPMH_REGULATOR_MODE_LPM>; + regulator-min-microvolt = <2960000>; + regulator-max-microvolt = <2960000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; }; vreg_l10c_3p3: ldo10 {@@ -254,6 +255,28 @@ status = "okay"; }; +&sdhc_1 { + status = "okay"; + + pinctrl-names = "default", "sleep"; + pinctrl-0 = <&sdc1_on>; + pinctrl-1 = <&sdc1_off>; + vmmc-supply = <&vreg_l19a_2p9>; + vqmmc-supply = <&vreg_l12a_1p8>; +}; + +&sdhc_2 { + status = "okay"; + + pinctrl-names = "default","sleep"; + pinctrl-0 = <&sdc2_on>; + pinctrl-1 = <&sdc2_off>; + vmmc-supply = <&vreg_l9c_2p9>; + vqmmc-supply = <&vreg_l6c_2p9>; + + cd-gpios = <&tlmm 69 GPIO_ACTIVE_LOW>; +}; + &uart3 { status = "okay"; };arch/arm64/boot/dts/qcom/sc7180.dtsi +148
-0@@ -226,6 +226,33 @@ }; }; + sdhc_1: sdhci@7c4000 { + compatible = "qcom,sc7180-sdhci", "qcom,sdhci-msm-v5"; + reg = <0 0x7c4000 0 0x1000>, + <0 0x07c5000 0 0x1000>; + reg-names = "hc_mem", "cqhci_mem"; + + iommus = <&apps_smmu 0x60 0x0>; + interrupts = <GIC_SPI 641 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 644 IRQ_TYPE_LEVEL_HIGH>; + interrupt-names = "hc_irq", "pwr_irq"; + + clocks = <&gcc GCC_SDCC1_APPS_CLK>, + <&gcc GCC_SDCC1_AHB_CLK>; + clock-names = "core", "iface"; + + bus-width = <8>; + non-removable; + supports-cqe; + + mmc-ddr-1_8v; + mmc-hs200-1_8v; + mmc-hs400-1_8v; + mmc-hs400-enhanced-strobe; + + status = "disabled"; + }; + qupv3_id_0: geniqup@8c0000 { compatible = "qcom,geni-se-qup"; reg = <0 0x008c0000 0 0x6000>;@@ -929,6 +956,127 @@ function = "qup15"; }; }; + + sdc1_on: sdc1-on { + pinconf-clk { + pins = "sdc1_clk"; + bias-disable; + drive-strength = <16>; + }; + + pinconf-cmd { + pins = "sdc1_cmd"; + bias-pull-up; + drive-strength = <10>; + }; + + pinconf-data { + pins = "sdc1_data"; + bias-pull-up; + drive-strength = <10>; + }; + + pinconf-rclk { + pins = "sdc1_rclk"; + bias-pull-down; + }; + }; + + sdc1_off: sdc1-off { + pinconf-clk { + pins = "sdc1_clk"; + bias-disable; + drive-strength = <2>; + }; + + pinconf-cmd { + pins = "sdc1_cmd"; + bias-pull-up; + drive-strength = <2>; + }; + + pinconf-data { + pins = "sdc1_data"; + bias-pull-up; + drive-strength = <2>; + }; + + pinconf-rclk { + pins = "sdc1_rclk"; + bias-pull-down; + }; + }; + + sdc2_on: sdc2-on { + pinconf-clk { + pins = "sdc2_clk"; + bias-disable; + drive-strength = <16>; + }; + + pinconf-cmd { + pins = "sdc2_cmd"; + bias-pull-up; + drive-strength = <10>; + }; + + pinconf-data { + pins = "sdc2_data"; + bias-pull-up; + drive-strength = <10>; + }; + + pinconf-sd-cd { + pins = "gpio69"; + bias-pull-up; + drive-strength = <2>; + }; + }; + + sdc2_off: sdc2-off { + pinconf-clk { + pins = "sdc2_clk"; + bias-disable; + drive-strength = <2>; + }; + + pinconf-cmd { + pins = "sdc2_cmd"; + bias-pull-up; + drive-strength = <2>; + }; + + pinconf-data { + pins = "sdc2_data"; + bias-pull-up; + drive-strength = <2>; + }; + + pinconf-sd-cd { + pins = "gpio69"; + bias-disable; + drive-strength = <2>; + }; + }; + }; + + sdhc_2: sdhci@8804000 { + compatible = "qcom,sc7180-sdhci", "qcom,sdhci-msm-v5"; + reg = <0 0x08804000 0 0x1000>; + reg-names = "hc_mem"; + + iommus = <&apps_smmu 0x80 0>; + interrupts = <GIC_SPI 204 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 222 IRQ_TYPE_LEVEL_HIGH>; + interrupt-names = "hc_irq", "pwr_irq"; + + clocks = <&gcc GCC_SDCC2_APPS_CLK>, + <&gcc GCC_SDCC2_AHB_CLK>; + clock-names = "core", "iface"; + + bus-width = <4>; + + status = "disabled"; }; qspi: spi@88dc000 {
Bjorn Andersson
AppliedQuoted 8 lines · Shaik Sajida Bhanu
From: Veerabhadrarao Badiganti <[email protected]>
Add sdhc instances for supporting eMMC and SD-card on sc7180. The regulators should be in HPM state for proper functionality of eMMC and SD-card. Updating corresponding regulators accordingly.
Signed-off-by Veerabhadrarao Badiganti <[email protected]>Signed-off-by Shaik Sajida Bhanu <[email protected]>
Applied
Regards,
Bjorn
Quoted 279 lines
---
Changes since V2:
- Added cmdq register space and support-cqe flag.
- Incorporated review comments by Matthias Kaehlcke.Changes since V1:
- Updated the regulator min, max voltages as per eMMC/SD-card voltage requirements
- Enabled IOMMU for eMMC and SD-card.
- Added pull and drive strength to SD-card cd-gpio.
- Incorporated review comments by Matthias Kaehlcke.--- arch/arm64/boot/dts/qcom/sc7180-idp.dts | 47 +++++++--- arch/arm64/boot/dts/qcom/sc7180.dtsi | 148 ++++++++++++++++++++++++++++++++ 2 files changed, 183 insertions(+), 12 deletions(-)arch/arm64/boot/dts/qcom/sc7180-idp.dts +35
-12@@ -7,6 +7,7 @@ /dts-v1/; +#include <dt-bindings/gpio/gpio.h> #include <dt-bindings/regulator/qcom,rpmh-regulator.h> #include "sc7180.dtsi" #include "pm6150.dtsi"@@ -101,9 +102,9 @@ }; vreg_l12a_1p8: ldo12 { - regulator-min-microvolt = <1696000>; - regulator-max-microvolt = <1952000>; - regulator-initial-mode = <RPMH_REGULATOR_MODE_LPM>; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; }; vreg_l13a_1p8: ldo13 {@@ -143,9 +144,9 @@ }; vreg_l19a_2p9: ldo19 { - regulator-min-microvolt = <2696000>; - regulator-max-microvolt = <3304000>; - regulator-initial-mode = <RPMH_REGULATOR_MODE_LPM>; + regulator-min-microvolt = <2960000>; + regulator-max-microvolt = <2960000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; }; };@@ -189,9 +190,9 @@ }; vreg_l6c_2p9: ldo6 { - regulator-min-microvolt = <2696000>; - regulator-max-microvolt = <3304000>; - regulator-initial-mode = <RPMH_REGULATOR_MODE_LPM>; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <2950000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; }; vreg_l7c_3p0: ldo7 {@@ -207,9 +208,9 @@ }; vreg_l9c_2p9: ldo9 { - regulator-min-microvolt = <2952000>; - regulator-max-microvolt = <3304000>; - regulator-initial-mode = <RPMH_REGULATOR_MODE_LPM>; + regulator-min-microvolt = <2960000>; + regulator-max-microvolt = <2960000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; }; vreg_l10c_3p3: ldo10 {@@ -254,6 +255,28 @@ status = "okay"; }; +&sdhc_1 { + status = "okay"; + + pinctrl-names = "default", "sleep"; + pinctrl-0 = <&sdc1_on>; + pinctrl-1 = <&sdc1_off>; + vmmc-supply = <&vreg_l19a_2p9>; + vqmmc-supply = <&vreg_l12a_1p8>; +}; + +&sdhc_2 { + status = "okay"; + + pinctrl-names = "default","sleep"; + pinctrl-0 = <&sdc2_on>; + pinctrl-1 = <&sdc2_off>; + vmmc-supply = <&vreg_l9c_2p9>; + vqmmc-supply = <&vreg_l6c_2p9>; + + cd-gpios = <&tlmm 69 GPIO_ACTIVE_LOW>; +}; + &uart3 { status = "okay"; };arch/arm64/boot/dts/qcom/sc7180.dtsi +148
-0@@ -226,6 +226,33 @@ }; }; + sdhc_1: sdhci@7c4000 { + compatible = "qcom,sc7180-sdhci", "qcom,sdhci-msm-v5"; + reg = <0 0x7c4000 0 0x1000>, + <0 0x07c5000 0 0x1000>; + reg-names = "hc_mem", "cqhci_mem"; + + iommus = <&apps_smmu 0x60 0x0>; + interrupts = <GIC_SPI 641 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 644 IRQ_TYPE_LEVEL_HIGH>; + interrupt-names = "hc_irq", "pwr_irq"; + + clocks = <&gcc GCC_SDCC1_APPS_CLK>, + <&gcc GCC_SDCC1_AHB_CLK>; + clock-names = "core", "iface"; + + bus-width = <8>; + non-removable; + supports-cqe; + + mmc-ddr-1_8v; + mmc-hs200-1_8v; + mmc-hs400-1_8v; + mmc-hs400-enhanced-strobe; + + status = "disabled"; + }; + qupv3_id_0: geniqup@8c0000 { compatible = "qcom,geni-se-qup"; reg = <0 0x008c0000 0 0x6000>;@@ -929,6 +956,127 @@ function = "qup15"; }; }; + + sdc1_on: sdc1-on { + pinconf-clk { + pins = "sdc1_clk"; + bias-disable; + drive-strength = <16>; + }; + + pinconf-cmd { + pins = "sdc1_cmd"; + bias-pull-up; + drive-strength = <10>; + }; + + pinconf-data { + pins = "sdc1_data"; + bias-pull-up; + drive-strength = <10>; + }; + + pinconf-rclk { + pins = "sdc1_rclk"; + bias-pull-down; + }; + }; + + sdc1_off: sdc1-off { + pinconf-clk { + pins = "sdc1_clk"; + bias-disable; + drive-strength = <2>; + }; + + pinconf-cmd { + pins = "sdc1_cmd"; + bias-pull-up; + drive-strength = <2>; + }; + + pinconf-data { + pins = "sdc1_data"; + bias-pull-up; + drive-strength = <2>; + }; + + pinconf-rclk { + pins = "sdc1_rclk"; + bias-pull-down; + }; + }; + + sdc2_on: sdc2-on { + pinconf-clk { + pins = "sdc2_clk"; + bias-disable; + drive-strength = <16>; + }; + + pinconf-cmd { + pins = "sdc2_cmd"; + bias-pull-up; + drive-strength = <10>; + }; + + pinconf-data { + pins = "sdc2_data"; + bias-pull-up; + drive-strength = <10>; + }; + + pinconf-sd-cd { + pins = "gpio69"; + bias-pull-up; + drive-strength = <2>; + }; + }; + + sdc2_off: sdc2-off { + pinconf-clk { + pins = "sdc2_clk"; + bias-disable; + drive-strength = <2>; + }; + + pinconf-cmd { + pins = "sdc2_cmd"; + bias-pull-up; + drive-strength = <2>; + }; + + pinconf-data { + pins = "sdc2_data"; + bias-pull-up; + drive-strength = <2>; + }; + + pinconf-sd-cd { + pins = "gpio69"; + bias-disable; + drive-strength = <2>; + }; + }; + }; + + sdhc_2: sdhci@8804000 { + compatible = "qcom,sc7180-sdhci", "qcom,sdhci-msm-v5"; + reg = <0 0x08804000 0 0x1000>; + reg-names = "hc_mem"; + + iommus = <&apps_smmu 0x80 0>; + interrupts = <GIC_SPI 204 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 222 IRQ_TYPE_LEVEL_HIGH>; + interrupt-names = "hc_irq", "pwr_irq"; + + clocks = <&gcc GCC_SDCC2_APPS_CLK>, + <&gcc GCC_SDCC2_AHB_CLK>; + clock-names = "core", "iface"; + + bus-width = <4>; + + status = "disabled"; }; qspi: spi@88dc000 {Signature · 2 lines
QUALCOMM INDIA, on behalf of Qualcomm Innovation Center, Inc. is a member of Code Aurora Forum, hosted by The Linux Foundation