Skip to contentSkip to conversation

net: mdio: add ipq8064 mdio driver

PATCH Superseded Ansuel Smith 1 participant 2 messages Feb 21, 2020

Subsystems (5)

v5 of 9 Superseded Latest is v9 →

lore
Share & tools
lore
#0 lore raw

PATCH v5 1/2 net: mdio: add ipq8064 mdio driver

Currently ipq806x soc use generi bitbang driver to comunicate with the gmac ethernet interface. Add a dedicated driver created by chunkeey to fix this.

Christian Lamparter <[email protected]>

---
 drivers/net/phy/Kconfig        |   8 ++
 drivers/net/phy/Makefile       |   1 +
 drivers/net/phy/mdio-ipq8064.c | 166 +++++++++++++++++++++++++++++++++
 3 files changed, 175 insertions(+)
 create mode 100644 drivers/net/phy/mdio-ipq8064.c
drivers/net/phy/Kconfig +8 -0
index 9dabe03a668c..ec2a5493a7e8 100644
@@ -157,6 +157,14 @@ config MDIO_I2C
 
 	  This is library mode.
 
+config MDIO_IPQ8064
+	tristate "Qualcomm IPQ8064 MDIO interface support"
+	depends on HAS_IOMEM && OF_MDIO
+	depends on MFD_SYSCON
+	help
+	  This driver supports the MDIO interface found in the network
+	  interface units of the IPQ8064 SoC
+
 config MDIO_MOXART
 	tristate "MOXA ART MDIO interface support"
 	depends on ARCH_MOXART || COMPILE_TEST
drivers/net/phy/Makefile +1 -0
index fe5badf13b65..8f02bd2089f3 100644
@@ -36,6 +36,7 @@ obj-$(CONFIG_MDIO_CAVIUM)	+= mdio-cavium.o
 obj-$(CONFIG_MDIO_GPIO)		+= mdio-gpio.o
 obj-$(CONFIG_MDIO_HISI_FEMAC)	+= mdio-hisi-femac.o
 obj-$(CONFIG_MDIO_I2C)		+= mdio-i2c.o
+obj-$(CONFIG_MDIO_IPQ8064)	+= mdio-ipq8064.o
 obj-$(CONFIG_MDIO_MOXART)	+= mdio-moxart.o
 obj-$(CONFIG_MDIO_MSCC_MIIM)	+= mdio-mscc-miim.o
 obj-$(CONFIG_MDIO_OCTEON)	+= mdio-octeon.o
drivers/net/phy/mdio-ipq8064.c new file +166 -0

166 lines not on this page · raw message

Signature · 1 line
2.25.0
#1 lore raw

PATCH v5 2/2 Documentation: devictree: Add ipq806x mdio bindings

Add documentations for ipq806x mdio driver.

---
 .../bindings/net/qcom,ipq8064-mdio.yaml       | 55 +++++++++++++++++++
 1 file changed, 55 insertions(+)
 create mode 100644 Documentation/devicetree/bindings/net/qcom,ipq8064-mdio.yaml
Documentation/devicetree/bindings/net/qcom,ipq8064-mdio.yaml new file +55 -0
new file mode 100644
index 000000000000..d2254a5ff2ad
@@ -0,0 +1,55 @@
+# SPDX-License-Identifier: GPL-2.0-or-later
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/net/qcom,ipq8064-mdio.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Qualcomm ipq806x MDIO bus controller
+
+maintainers:
+  - Ansuel Smith <[email protected]>
+
+description: |+
+  The ipq806x soc have a MDIO dedicated controller that is
+  used to comunicate with the gmac phy conntected.
+  Child nodes of this MDIO bus controller node are standard
+  Ethernet PHY device nodes as described in
+  Documentation/devicetree/bindings/net/phy.txt
+
+allOf:
+  - $ref: "mdio.yaml#"
+
+properties:
+  compatible:
+    const: qcom,ipq8064-mdio
+  reg:
+    maxItems: 1
+    description: address and length of the register set for the device
+  clocks:
+    maxItems: 1
+    description: A reference to the clock supplying the MDIO bus controller
+
+required:
+  - compatible
+  - reg
+  - clocks
+  - "#address-cells"
+  - "#size-cells"
+
+examples:
+  - |
+    mdio0: mdio@37000000 {
+        #address-cells = <1>;
+        #size-cells = <0>;
+
+        compatible = "qcom,ipq8064-mdio", "syscon";
+        reg = <0x37000000 0x200000>;
+        resets = <&gcc GMAC_CORE1_RESET>;
+        reset-names = "stmmaceth";
+        clocks = <&gcc GMAC_CORE1_CLK>;
+
+        switch@10 {
+            compatible = "qca,qca8337";
+            ...
+        }
+    };
Signature · 1 line
2.25.0