Skip to contentSkip to conversation

marvell10g tunable and power saving support

PATCH In review Russell King - ARM Linux admin 5 participants 10 messages Mar 3, 2020 – Mar 9, 2020

Subsystems (4)
Networking Network drivers Ethernet PHY Marvell MV88X3310 PHY driver
lore
Share & tools
lore

Russell King - ARM Linux admin

author maintainer
#0 lore raw

v3 cover marvell10g tunable and power saving support

Hi,

This patch series adds support for:
- mdix configuration (auto, mdi, mdix)
- energy detect power down (edpd)
- placing in edpd mode at probe

for both the 88x3310 and 88x2110 PHYs.

Antione, could you test this for the 88x2110 PHY please?

v3: fix return code in get_tunable/set_tunable
v2: fix comments from Antione.

 drivers/net/phy/marvell10g.c | 177 +++++++++++++++++++++++++++++++++++++++++--
 1 file changed, 170 insertions(+), 7 deletions(-)
Signature · 3 lines
RMK's Patch system: https://www.armlinux.org.uk/developer/patches/
FTTC broadband for 0.8mile line in suburbia: sync at 12.1Mbps down 622kbps up
According to speedtest.net: 11.9Mbps down 500kbps up
#1 lore raw

PATCH v3 1/3 net: phy: marvell10g: add mdix control

Add support for controlling the MDI-X state of the PHY.

Signed-off-by Russell King <[email protected]>
---
 drivers/net/phy/marvell10g.c | 61 ++++++++++++++++++++++++++++++++++--
 1 file changed, 59 insertions(+), 2 deletions(-)
drivers/net/phy/marvell10g.c +59 -2
index 9a4e12a2af07..9d4fed782b19 100644
@@ -23,6 +23,7 @@
  * link takes priority and the other port is completely locked out.
  */
 #include <linux/ctype.h>
+#include <linux/delay.h>
 #include <linux/hwmon.h>
 #include <linux/marvell_phy.h>
 #include <linux/phy.h>

@@ -39,6 +40,12 @@ enum {
 	MV_PCS_BASE_R		= 0x1000,
 	MV_PCS_1000BASEX	= 0x2000,
 
+	MV_PCS_CSCR1		= 0x8000,
+	MV_PCS_CSCR1_MDIX_MASK	= 0x0060,
+	MV_PCS_CSCR1_MDIX_MDI	= 0x0000,
+	MV_PCS_CSCR1_MDIX_MDIX	= 0x0020,
+	MV_PCS_CSCR1_MDIX_AUTO	= 0x0060,
+
 	MV_PCS_CSSR1		= 0x8008,
 	MV_PCS_CSSR1_SPD1_MASK	= 0xc000,
 	MV_PCS_CSSR1_SPD1_SPD2	= 0xc000,

@@ -216,6 +223,26 @@ static int mv3310_hwmon_probe(struct phy_device *phydev)
 }
 #endif
 
+static int mv3310_reset(struct phy_device *phydev, u32 unit)
+{
+	int retries, val, err;
+
+	err = phy_modify_mmd(phydev, MDIO_MMD_PCS, unit + MDIO_CTRL1,
+			     MDIO_CTRL1_RESET, MDIO_CTRL1_RESET);
+	if (err < 0)
+		return err;
+
+	retries = 20;
+	do {
+		msleep(5);
+		val = phy_read_mmd(phydev, MDIO_MMD_PCS, unit + MDIO_CTRL1);
+		if (val < 0)
+			return val;
+	} while (val & MDIO_CTRL1_RESET && --retries);
+
+	return val & MDIO_CTRL1_RESET ? -ETIMEDOUT : 0;
+}
+
 static int mv3310_sfp_insert(void *upstream, const struct sfp_eeprom_id *id)
 {
 	struct phy_device *phydev = upstream;

@@ -316,6 +343,8 @@ static int mv3310_config_init(struct phy_device *phydev)
 	    phydev->interface != PHY_INTERFACE_MODE_10GBASER)
 		return -ENODEV;
 
+	phydev->mdix_ctrl = ETH_TP_MDI_AUTO;
+
 	return 0;
 }
 

@@ -345,14 +374,42 @@ static int mv3310_get_features(struct phy_device *phydev)
 	return 0;
 }
 
+static int mv3310_config_mdix(struct phy_device *phydev)
+{
+	u16 val;
+	int err;
+
+	switch (phydev->mdix_ctrl) {
+	case ETH_TP_MDI_AUTO:
+		val = MV_PCS_CSCR1_MDIX_AUTO;
+		break;
+	case ETH_TP_MDI_X:
+		val = MV_PCS_CSCR1_MDIX_MDIX;
+		break;
+	case ETH_TP_MDI:
+		val = MV_PCS_CSCR1_MDIX_MDI;
+		break;
+	default:
+		return -EINVAL;
+	}
+
+	err = phy_modify_mmd_changed(phydev, MDIO_MMD_PCS, MV_PCS_CSCR1,
+				     MV_PCS_CSCR1_MDIX_MASK, val);
+	if (err > 0)
+		err = mv3310_reset(phydev, MV_PCS_BASE_T);
+
+	return err;
+}
+
 static int mv3310_config_aneg(struct phy_device *phydev)
 {
 	bool changed = false;
 	u16 reg;
 	int ret;
 
-	/* We don't support manual MDI control */
-	phydev->mdix_ctrl = ETH_TP_MDI_AUTO;
+	ret = mv3310_config_mdix(phydev);
+	if (ret < 0)
+		return ret;
 
 	if (phydev->autoneg == AUTONEG_DISABLE)
 		return genphy_c45_pma_setup_forced(phydev);
Signature · 1 line
2.20.1
maintainer
#3 lore raw

Re: [PATCH net-next v3 1/3] net: phy: marvell10g: add mdix control

From: Andrew Lunn <[email protected]>
Date: Tue, 3 Mar 2020 20:53:52 +0100

Quoted 3 lines

It would be nice to have Antoine test this before it get merged, but:

Reviewed-by Andrew Lunn <[email protected]>

Ok, I'll give Antoine a chance to test it out.

author maintainer
#4 lore raw

Re: [PATCH net-next v3 1/3] net: phy: marvell10g: add mdix control

Quoted 8 lines · David Miller

From: Andrew Lunn <[email protected]>
Date: Tue, 3 Mar 2020 20:53:52 +0100

Quoted 3 lines

It would be nice to have Antoine test this before it get merged, but:

Reviewed-by Andrew Lunn <[email protected]>

Ok, I'll give Antoine a chance to test it out.

Hi David,

Antoine has now tested it - do I need to resubmit now?

Thanks.

Signature · 3 lines
RMK's Patch system: https://www.armlinux.org.uk/developer/patches/
FTTC broadband for 0.8mile line in suburbia: sync at 12.1Mbps down 622kbps up
According to speedtest.net: 11.9Mbps down 500kbps up
maintainer
#5 lore raw

Re: [PATCH net-next v3 1/3] net: phy: marvell10g: add mdix control

From: Russell King - ARM Linux admin <[email protected]>
Date: Sat, 7 Mar 2020 09:07:41 +0000

Quoted 6 lines · David Miller
Quoted 5 lines

From: Andrew Lunn <[email protected]>
Date: Tue, 3 Mar 2020 20:53:52 +0100

Quoted 2 lines

It would be nice to have Antoine test this before it get merged, but:

Quoted 7 lines
Quoted 3 lines
Quoted 1 line
Reviewed-by Andrew Lunn <[email protected]>

Ok, I'll give Antoine a chance to test it out.

Hi David,

Antoine has now tested it - do I need to resubmit now?

I am pretty sure I applied this series to net-next. :-)

#6 lore raw

PATCH v3 2/3 net: phy: marvell10g: add energy detect power down tunable

In reply to Russell King - ARM Linux admin

Add support for the energy detect power down tunable, which saves around 600mW when the link is down. The 88x3310 supports off, rx-only and NLP every second. Enable EDPD by default for 88x3310.

Signed-off-by Russell King <[email protected]>
---
 drivers/net/phy/marvell10g.c | 86 +++++++++++++++++++++++++++++++++++-
 1 file changed, 85 insertions(+), 1 deletion(-)
drivers/net/phy/marvell10g.c +85 -1
index 9d4fed782b19..7092feb9e6b5 100644
@@ -41,6 +41,10 @@ enum {
 	MV_PCS_1000BASEX	= 0x2000,
 
 	MV_PCS_CSCR1		= 0x8000,
+	MV_PCS_CSCR1_ED_MASK	= 0x0300,
+	MV_PCS_CSCR1_ED_OFF	= 0x0000,
+	MV_PCS_CSCR1_ED_RX	= 0x0200,
+	MV_PCS_CSCR1_ED_NLP	= 0x0300,
 	MV_PCS_CSCR1_MDIX_MASK	= 0x0060,
 	MV_PCS_CSCR1_MDIX_MDI	= 0x0000,
 	MV_PCS_CSCR1_MDIX_MDIX	= 0x0020,

@@ -243,6 +247,59 @@ static int mv3310_reset(struct phy_device *phydev, u32 unit)
 	return val & MDIO_CTRL1_RESET ? -ETIMEDOUT : 0;
 }
 
+static int mv3310_get_edpd(struct phy_device *phydev, u16 *edpd)
+{
+	int val;
+
+	val = phy_read_mmd(phydev, MDIO_MMD_PCS, MV_PCS_CSCR1);
+	if (val < 0)
+		return val;
+
+	switch (val & MV_PCS_CSCR1_ED_MASK) {
+	case MV_PCS_CSCR1_ED_NLP:
+		*edpd = 1000;
+		break;
+	case MV_PCS_CSCR1_ED_RX:
+		*edpd = ETHTOOL_PHY_EDPD_NO_TX;
+		break;
+	default:
+		*edpd = ETHTOOL_PHY_EDPD_DISABLE;
+		break;
+	}
+	return 0;
+}
+
+static int mv3310_set_edpd(struct phy_device *phydev, u16 edpd)
+{
+	u16 val;
+	int err;
+
+	switch (edpd) {
+	case 1000:
+	case ETHTOOL_PHY_EDPD_DFLT_TX_MSECS:
+		val = MV_PCS_CSCR1_ED_NLP;
+		break;
+
+	case ETHTOOL_PHY_EDPD_NO_TX:
+		val = MV_PCS_CSCR1_ED_RX;
+		break;
+
+	case ETHTOOL_PHY_EDPD_DISABLE:
+		val = MV_PCS_CSCR1_ED_OFF;
+		break;
+
+	default:
+		return -EINVAL;
+	}
+
+	err = phy_modify_mmd_changed(phydev, MDIO_MMD_PCS, MV_PCS_CSCR1,
+				     MV_PCS_CSCR1_ED_MASK, val);
+	if (err > 0)
+		err = mv3310_reset(phydev, MV_PCS_BASE_T);
+
+	return err;
+}
+
 static int mv3310_sfp_insert(void *upstream, const struct sfp_eeprom_id *id)
 {
 	struct phy_device *phydev = upstream;

@@ -345,7 +402,8 @@ static int mv3310_config_init(struct phy_device *phydev)
 
 	phydev->mdix_ctrl = ETH_TP_MDI_AUTO;
 
-	return 0;
+	/* Enable EDPD mode - saving 600mW */
+	return mv3310_set_edpd(phydev, ETHTOOL_PHY_EDPD_DFLT_TX_MSECS);
 }
 
 static int mv3310_get_features(struct phy_device *phydev)

@@ -594,6 +652,28 @@ static int mv3310_read_status(struct phy_device *phydev)
 	return 0;
 }
 
+static int mv3310_get_tunable(struct phy_device *phydev,
+			      struct ethtool_tunable *tuna, void *data)
+{
+	switch (tuna->id) {
+	case ETHTOOL_PHY_EDPD:
+		return mv3310_get_edpd(phydev, data);
+	default:
+		return -EOPNOTSUPP;
+	}
+}
+
+static int mv3310_set_tunable(struct phy_device *phydev,
+			      struct ethtool_tunable *tuna, const void *data)
+{
+	switch (tuna->id) {
+	case ETHTOOL_PHY_EDPD:
+		return mv3310_set_edpd(phydev, *(u16 *)data);
+	default:
+		return -EOPNOTSUPP;
+	}
+}
+
 static struct phy_driver mv3310_drivers[] = {
 	{
 		.phy_id		= MARVELL_PHY_ID_88X3310,

@@ -608,6 +688,8 @@ static struct phy_driver mv3310_drivers[] = {
 		.config_aneg	= mv3310_config_aneg,
 		.aneg_done	= mv3310_aneg_done,
 		.read_status	= mv3310_read_status,
+		.get_tunable	= mv3310_get_tunable,
+		.set_tunable	= mv3310_set_tunable,
 	},
 	{
 		.phy_id		= MARVELL_PHY_ID_88E2110,

@@ -621,6 +703,8 @@ static struct phy_driver mv3310_drivers[] = {
 		.config_aneg	= mv3310_config_aneg,
 		.aneg_done	= mv3310_aneg_done,
 		.read_status	= mv3310_read_status,
+		.get_tunable	= mv3310_get_tunable,
+		.set_tunable	= mv3310_set_tunable,
 	},
 };
Signature · 1 line
2.20.1
maintainer Reviewed-by on v3 2/3
#7 lore raw

Re: [PATCH net-next v3 2/3] net: phy: marvell10g: add energy detect power down tunable

Quoted 5 lines · Russell King

Add support for the energy detect power down tunable, which saves around 600mW when the link is down. The 88x3310 supports off, rx-only and NLP every second. Enable EDPD by default for 88x3310.

Signed-off-by Russell King <[email protected]>
Reviewed-by Andrew Lunn <[email protected]>

Andrew

#8 lore raw

PATCH v3 3/3 net: phy: marvell10g: place in powersave mode at probe

In reply to Russell King - ARM Linux admin

Place the 88x3310 into powersaving mode when probing, which saves 600mW per PHY. For both PHYs on the Macchiatobin double-shot, this saves about 10% of the board idle power.

Reviewed-by Andrew Lunn <[email protected]>
Signed-off-by Russell King <[email protected]>
---
 drivers/net/phy/marvell10g.c | 30 ++++++++++++++++++++++++++----
 1 file changed, 26 insertions(+), 4 deletions(-)
drivers/net/phy/marvell10g.c +26 -4
index 7092feb9e6b5..7e05b92504f0 100644
@@ -227,6 +227,18 @@ static int mv3310_hwmon_probe(struct phy_device *phydev)
 }
 #endif
 
+static int mv3310_power_down(struct phy_device *phydev)
+{
+	return phy_set_bits_mmd(phydev, MDIO_MMD_VEND2, MV_V2_PORT_CTRL,
+				MV_V2_PORT_CTRL_PWRDOWN);
+}
+
+static int mv3310_power_up(struct phy_device *phydev)
+{
+	return phy_clear_bits_mmd(phydev, MDIO_MMD_VEND2, MV_V2_PORT_CTRL,
+				  MV_V2_PORT_CTRL_PWRDOWN);
+}
+
 static int mv3310_reset(struct phy_device *phydev, u32 unit)
 {
 	int retries, val, err;

@@ -348,6 +360,11 @@ static int mv3310_probe(struct phy_device *phydev)
 
 	dev_set_drvdata(&phydev->mdio.dev, priv);
 
+	/* Powering down the port when not in use saves about 600mW */
+	ret = mv3310_power_down(phydev);
+	if (ret)
+		return ret;
+
 	ret = mv3310_hwmon_probe(phydev);
 	if (ret)
 		return ret;

@@ -357,16 +374,14 @@ static int mv3310_probe(struct phy_device *phydev)
 
 static int mv3310_suspend(struct phy_device *phydev)
 {
-	return phy_set_bits_mmd(phydev, MDIO_MMD_VEND2, MV_V2_PORT_CTRL,
-				MV_V2_PORT_CTRL_PWRDOWN);
+	return mv3310_power_down(phydev);
 }
 
 static int mv3310_resume(struct phy_device *phydev)
 {
 	int ret;
 
-	ret = phy_clear_bits_mmd(phydev, MDIO_MMD_VEND2, MV_V2_PORT_CTRL,
-				 MV_V2_PORT_CTRL_PWRDOWN);
+	ret = mv3310_power_up(phydev);
 	if (ret)
 		return ret;
 

@@ -392,6 +407,8 @@ static bool mv3310_has_pma_ngbaset_quirk(struct phy_device *phydev)
 
 static int mv3310_config_init(struct phy_device *phydev)
 {
+	int err;
+
 	/* Check that the PHY interface type is compatible */
 	if (phydev->interface != PHY_INTERFACE_MODE_SGMII &&
 	    phydev->interface != PHY_INTERFACE_MODE_2500BASEX &&

@@ -402,6 +419,11 @@ static int mv3310_config_init(struct phy_device *phydev)
 
 	phydev->mdix_ctrl = ETH_TP_MDI_AUTO;
 
+	/* Power up so reset works */
+	err = mv3310_power_up(phydev);
+	if (err)
+		return err;
+
 	/* Enable EDPD mode - saving 600mW */
 	return mv3310_set_edpd(phydev, ETHTOOL_PHY_EDPD_DFLT_TX_MSECS);
 }
Signature · 1 line
2.20.1
Tested-by on the v3 series
#9 lore raw
In reply to Russell King - ARM Linux admin

Hello Russell,

Quoted 9 lines · Russell King - ARM Linux admin

This patch series adds support for:
- mdix configuration (auto, mdi, mdix)
- energy detect power down (edpd)
- placing in edpd mode at probe

for both the 88x3310 and 88x2110 PHYs.

Antione, could you test this for the 88x2110 PHY please?

Tested-by Antoine Tenart <[email protected]>

Thanks!
Antoine

Quoted 10 lines

v3: fix return code in get_tunable/set_tunable
v2: fix comments from Antione.

 drivers/net/phy/marvell10g.c | 177 +++++++++++++++++++++++++++++++++++++++++--
 1 file changed, 170 insertions(+), 7 deletions(-)
Signature · 3 lines
RMK's Patch system: https://www.armlinux.org.uk/developer/patches/
FTTC broadband for 0.8mile line in suburbia: sync at 12.1Mbps down 622kbps up
According to speedtest.net: 11.9Mbps down 500kbps up
Signature · 3 lines
Antoine Ténart, Bootlin
Embedded Linux and Kernel engineering
https://bootlin.com