dt-bindings: i2c: convert rockchip i2c bindings to yaml
Subsystems (3)
PATCH 1/5 dt-bindings: i2c: convert rockchip i2c bindings to yaml
Current dts files with 'i2c' nodes are manually verified. In order to automate this process i2c-rk3x.txt has to be converted to yaml. In the new setup i2c-rk3x.yaml will inherit properties from i2c-controller.yaml.
Also change document name in MAINTAINERS.
--- Documentation/devicetree/bindings/i2c/i2c-rk3x.txt | 68 ----------- .../devicetree/bindings/i2c/i2c-rk3x.yaml | 129 +++++++++++++++++++++ MAINTAINERS | 2 +- 3 files changed, 130 insertions(+), 69 deletions(-) delete mode 100644 Documentation/devicetree/bindings/i2c/i2c-rk3x.txt create mode 100644 Documentation/devicetree/bindings/i2c/i2c-rk3x.yaml
Documentation/devicetree/bindings/i2c/i2c-rk3x.txt deleted +0 -68
@@ -1,68 +0,0 @@ -* Rockchip RK3xxx I2C controller - -This driver interfaces with the native I2C controller present in Rockchip -RK3xxx SoCs. - -Required properties : - - - reg : Offset and length of the register set for the device - - compatible: should be one of the following: - - "rockchip,rv1108-i2c": for rv1108 - - "rockchip,rk3066-i2c": for rk3066 - - "rockchip,rk3188-i2c": for rk3188 - - "rockchip,rk3228-i2c": for rk3228 - - "rockchip,rk3288-i2c": for rk3288 - - "rockchip,rk3328-i2c", "rockchip,rk3399-i2c": for rk3328 - - "rockchip,rk3399-i2c": for rk3399 - - interrupts : interrupt number - - clocks: See ../clock/clock-bindings.txt - - For older hardware (rk3066, rk3188, rk3228, rk3288): - - There is one clock that's used both to derive the functional clock - for the device and as the bus clock. - - For newer hardware (rk3399): specified by name - - "i2c": This is used to derive the functional clock. - - "pclk": This is the bus clock. - -Required on RK3066, RK3188 : - - - rockchip,grf : the phandle of the syscon node for the general register - file (GRF) - - on those SoCs an alias with the correct I2C bus ID (bit offset in the GRF) - is also required. - -Optional properties : - - - clock-frequency : SCL frequency to use (in Hz). If omitted, 100kHz is used. - - i2c-scl-rising-time-ns : Number of nanoseconds the SCL signal takes to rise - (t(r) in I2C specification). If not specified this is assumed to be - the maximum the specification allows(1000 ns for Standard-mode, - 300 ns for Fast-mode) which might cause slightly slower communication. - - i2c-scl-falling-time-ns : Number of nanoseconds the SCL signal takes to fall - (t(f) in the I2C specification). If not specified this is assumed to - be the maximum the specification allows (300 ns) which might cause - slightly slower communication. - - i2c-sda-falling-time-ns : Number of nanoseconds the SDA signal takes to fall - (t(f) in the I2C specification). If not specified we'll use the SCL - value since they are the same in nearly all cases. - -Example: - -aliases { - i2c0 = &i2c0; -} - -i2c0: i2c@2002d000 { - compatible = "rockchip,rk3188-i2c"; - reg = <0x2002d000 0x1000>; - interrupts = <GIC_SPI 40 IRQ_TYPE_LEVEL_HIGH>; - #address-cells = <1>; - #size-cells = <0>; - - rockchip,grf = <&grf>; - - clock-names = "i2c"; - clocks = <&cru PCLK_I2C0>; - - i2c-scl-rising-time-ns = <800>; - i2c-scl-falling-time-ns = <100>; -};
Documentation/devicetree/bindings/i2c/i2c-rk3x.yaml new file +129 -0
129 lines not on this page · raw message
MAINTAINERS +1 -1
@@ -2279,7 +2279,7 @@ L: linux-arm-kernel-IAPFreCvJWM7uuMidbF8XUB+6BGkLq7r@public.gmane.org (moderated for non-subscribers) L: [email protected] T: git git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip.git S: Maintained -F: Documentation/devicetree/bindings/i2c/i2c-rk3x.txt +F: Documentation/devicetree/bindings/i2c/i2c-rk3x.yaml F: Documentation/devicetree/bindings/mmc/rockchip-dw-mshc.yaml F: Documentation/devicetree/bindings/spi/spi-rockchip.yaml F: arch/arm/boot/dts/rk3*
Signature · 1 line
2.11.0
PATCH 2/5 dt-bindings: i2c: i2c-rk3x: add description for rk3036
The description below is already in use for rk3036.dtsi, but was somehow never added to a document, so add "rockchip,rk3036-i2c", "rockchip,rk3288-i2c" for i2c nodes on a rk3036 platform to i2c-rk3x.yaml.
--- Documentation/devicetree/bindings/i2c/i2c-rk3x.yaml | 4 ++++ 1 file changed, 4 insertions(+)
Documentation/devicetree/bindings/i2c/i2c-rk3x.yaml +4 -0
@@ -28,6 +28,10 @@ properties: - const: rockchip,rk3399-i2c - items: - enum: + - rockchip,rk3036-i2c + - const: rockchip,rk3288-i2c + - items: + - enum: - rockchip,rk3328-i2c - const: rockchip,rk3399-i2c
Signature · 1 line
2.11.0
Re: [PATCH v1 2/5] dt-bindings: i2c: i2c-rk3x: add description for rk3036
Quoted 10 lines · Johan Jonker
The description below is already in use for
rk3036.dtsi, but was somehow never added to a document, so add "rockchip,rk3036-i2c", "rockchip,rk3288-i2c" for i2c nodes on a rk3036 platform toi2c-rk3x.yaml.Signed-off-by Johan Jonker <[email protected]>--- Documentation/devicetree/bindings/i2c/i2c-rk3x.yaml | 4 ++++ 1 file changed, 4 insertions(+)
PATCH 3/5 dt-bindings: i2c: i2c-rk3x: add description for rk3368
In reply to Johan JonkerThe description below is already in use for rk3368.dtsi, but was somehow never added to a document, so add "rockchip,rk3368-i2c", "rockchip,rk3288-i2c" for i2c nodes on a rk3368 platform to i2c-rk3x.yaml.
--- Documentation/devicetree/bindings/i2c/i2c-rk3x.yaml | 1 + 1 file changed, 1 insertion(+)
Documentation/devicetree/bindings/i2c/i2c-rk3x.yaml +1 -0
@@ -29,6 +29,7 @@ properties: - items: - enum: - rockchip,rk3036-i2c + - rockchip,rk3368-i2c - const: rockchip,rk3288-i2c - items: - enum:
Signature · 1 line
2.11.0
Re: [PATCH v1 3/5] dt-bindings: i2c: i2c-rk3x: add description for rk3368
Quoted 10 lines · Johan Jonker
The description below is already in use for
rk3368.dtsi, but was somehow never added to a document, so add "rockchip,rk3368-i2c", "rockchip,rk3288-i2c" for i2c nodes on a rk3368 platform toi2c-rk3x.yaml.Signed-off-by Johan Jonker <[email protected]>--- Documentation/devicetree/bindings/i2c/i2c-rk3x.yaml | 1 + 1 file changed, 1 insertion(+)
PATCH 4/5 dt-bindings: i2c: i2c-rk3x: add description for rk3308
In reply to Johan JonkerThe description below is already in use for rk3308.dtsi, but was somehow never added to a document, so add "rockchip,rk3308-i2c", "rockchip,rk3399-i2c" for i2c nodes on a rk3308 platform to i2c-rk3x.yaml.
--- Documentation/devicetree/bindings/i2c/i2c-rk3x.yaml | 1 + 1 file changed, 1 insertion(+)
Documentation/devicetree/bindings/i2c/i2c-rk3x.yaml +1 -0
@@ -33,6 +33,7 @@ properties: - const: rockchip,rk3288-i2c - items: - enum: + - rockchip,rk3308-i2c - rockchip,rk3328-i2c - const: rockchip,rk3399-i2c
Signature · 1 line
2.11.0
Re: [PATCH v1 4/5] dt-bindings: i2c: i2c-rk3x: add description for rk3308
Quoted 10 lines · Johan Jonker
The description below is already in use for
rk3308.dtsi, but was somehow never added to a document, so add "rockchip,rk3308-i2c", "rockchip,rk3399-i2c" for i2c nodes on a rk3308 platform toi2c-rk3x.yaml.Signed-off-by Johan Jonker <[email protected]>--- Documentation/devicetree/bindings/i2c/i2c-rk3x.yaml | 1 + 1 file changed, 1 insertion(+)
PATCH 5/5 dt-bindings: i2c: i2c-rk3x: add description for px30
In reply to Johan JonkerThe description below is already in use for px30.dtsi, but was somehow never added to a document, so add "rockchip,px30-i2c", "rockchip,rk3399-i2c" for i2c nodes on a px30 platform to i2c-rk3x.yaml.
--- Documentation/devicetree/bindings/i2c/i2c-rk3x.yaml | 1 + 1 file changed, 1 insertion(+)
Documentation/devicetree/bindings/i2c/i2c-rk3x.yaml +1 -0
@@ -33,6 +33,7 @@ properties: - const: rockchip,rk3288-i2c - items: - enum: + - rockchip,px30-i2c - rockchip,rk3308-i2c - rockchip,rk3328-i2c - const: rockchip,rk3399-i2c
Signature · 1 line
2.11.0
Quoted 8 lines · Johan Jonker
Current dts files with 'i2c' nodes are manually verified. In order to automate this process i2c-rk3x.txt has to be converted to yaml. In the new setup
i2c-rk3x.yamlwill inherit properties fromi2c-controller.yaml.Also change document name in
MAINTAINERS.
Quoted 9 lines
Signed-off-by Johan Jonker <[email protected]>--- Documentation/devicetree/bindings/i2c/i2c-rk3x.txt | 68 ----------- .../devicetree/bindings/i2c/i2c-rk3x.yaml | 129 +++++++++++++++++++++ MAINTAINERS | 2 +- 3 files changed, 130 insertions(+), 69 deletions(-) delete mode 100644 Documentation/devicetree/bindings/i2c/i2c-rk3x.txt create mode 100644 Documentation/devicetree/bindings/i2c/i2c-rk3x.yaml
Rob Herring
maintainerQuoted 19 lines · Rob Herring
Quoted 8 lines · Johan Jonker
Current dts files with 'i2c' nodes are manually verified. In order to automate this process i2c-rk3x.txt has to be converted to yaml. In the new setup
i2c-rk3x.yamlwill inherit properties fromi2c-controller.yaml.Also change document name in
MAINTAINERS.Quoted 9 lines
Signed-off-by Johan Jonker <[email protected]>--- Documentation/devicetree/bindings/i2c/i2c-rk3x.txt | 68 ----------- .../devicetree/bindings/i2c/i2c-rk3x.yaml | 129 +++++++++++++++++++++ MAINTAINERS | 2 +- 3 files changed, 130 insertions(+), 69 deletions(-) delete mode 100644 Documentation/devicetree/bindings/i2c/i2c-rk3x.txt create mode 100644 Documentation/devicetree/bindings/i2c/i2c-rk3x.yaml
Quoted 1 line
Reviewed-by Rob Herring <[email protected]>
As this series is all binding changes, I'll take it via the DT tree.
Rob