dt-bindings: serial: lpuart: add ls1028a compatibility
PATCH v2 1/2 dt-bindings: serial: lpuart: add ls1028a compatibility
Add the LS1028A SoC compatibility string to the lpuart devicetree bindings documentation.
Signed-off-by Michael Walle <[email protected]>
Reviewed-by Rob Herring <[email protected]>
---
changes since v1:
- add changelog text
.../devicetree/bindings/serial/fsl-lpuart.txt | 10 ++++++---- 1 file changed, 6 insertions(+), 4 deletions(-)
Documentation/devicetree/bindings/serial/fsl-lpuart.txt +6 -4
@@ -6,6 +6,8 @@ Required properties: on Vybrid vf610 SoC with 8-bit register organization - "fsl,ls1021a-lpuart" for lpuart compatible with the one integrated on LS1021A SoC with 32-bit big-endian register organization + - "fsl,ls1028a-lpuart" for lpuart compatible with the one integrated + on LS1028A SoC with 32-bit little-endian register organization - "fsl,imx7ulp-lpuart" for lpuart compatible with the one integrated on i.MX7ULP SoC with 32-bit little-endian register organization - "fsl,imx8qxp-lpuart" for lpuart compatible with the one integrated
@@ -15,10 +17,10 @@ Required properties: - reg : Address and length of the register set for the device - interrupts : Should contain uart interrupt - clocks : phandle + clock specifier pairs, one for each entry in clock-names -- clock-names : For vf610/ls1021a/imx7ulp, "ipg" clock is for uart bus/baud - clock. For imx8qxp lpuart, "ipg" clock is bus clock that is used to access - lpuart controller registers, it also requires "baud" clock for module to - receive/transmit data. +- clock-names : For vf610/ls1021a/ls1028a/imx7ulp, "ipg" clock is for uart + bus/baud clock. For imx8qxp lpuart, "ipg" clock is bus clock that is used + to access lpuart controller registers, it also requires "baud" clock for + module to receive/transmit data. Optional properties: - dmas: A list of two dma specifiers, one for each entry in dma-names.
Signature · 1 line
2.20.1
PATCH v2 2/2 arm64: dts: ls1028a: add missing LPUART nodes
The LS1028A has six LPUART controllers. Add the nodes.
This was tested on a custom board.
Signed-off-by Michael Walle <[email protected]>
---
changes since v1:
- none
.../arm64/boot/dts/freescale/fsl-ls1028a.dtsi | 73 +++++++++++++++++++ 1 file changed, 73 insertions(+)
arch/arm64/boot/dts/freescale/fsl-ls1028a.dtsi +73 -0
@@ -372,6 +372,79 @@ status = "disabled"; }; + + lpuart0: serial@2260000 { + compatible = "fsl,ls1028a-lpuart"; + reg = <0x0 0x2260000 0x0 0x1000>; + interrupts = <GIC_SPI 232 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&clockgen 4 1>; + clock-names = "ipg"; + dma-names = "rx","tx"; + dmas = <&edma0 1 32>, + <&edma0 1 33>; + status = "disabled"; + }; + + lpuart1: serial@2270000 { + compatible = "fsl,ls1028a-lpuart"; + reg = <0x0 0x2270000 0x0 0x1000>; + interrupts = <GIC_SPI 233 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&clockgen 4 1>; + clock-names = "ipg"; + dma-names = "rx","tx"; + dmas = <&edma0 1 30>, + <&edma0 1 31>; + status = "disabled"; + }; + + lpuart2: serial@2280000 { + compatible = "fsl,ls1028a-lpuart"; + reg = <0x0 0x2280000 0x0 0x1000>; + interrupts = <GIC_SPI 234 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&clockgen 4 1>; + clock-names = "ipg"; + dma-names = "rx","tx"; + dmas = <&edma0 1 28>, + <&edma0 1 29>; + status = "disabled"; + }; + + lpuart3: serial@2290000 { + compatible = "fsl,ls1028a-lpuart"; + reg = <0x0 0x2290000 0x0 0x1000>; + interrupts = <GIC_SPI 235 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&clockgen 4 1>; + clock-names = "ipg"; + dma-names = "rx","tx"; + dmas = <&edma0 1 26>, + <&edma0 1 27>; + status = "disabled"; + }; + + lpuart4: serial@22a0000 { + compatible = "fsl,ls1028a-lpuart"; + reg = <0x0 0x22a0000 0x0 0x1000>; + interrupts = <GIC_SPI 236 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&clockgen 4 1>; + clock-names = "ipg"; + dma-names = "rx","tx"; + dmas = <&edma0 1 24>, + <&edma0 1 25>; + status = "disabled"; + }; + + lpuart5: serial@22b0000 { + compatible = "fsl,ls1028a-lpuart"; + reg = <0x0 0x22b0000 0x0 0x1000>; + interrupts = <GIC_SPI 237 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&clockgen 4 1>; + clock-names = "ipg"; + dma-names = "rx","tx"; + dmas = <&edma0 1 22>, + <&edma0 1 23>; + status = "disabled"; + }; + edma0: dma-controller@22c0000 { #dma-cells = <2>; compatible = "fsl,ls1028a-edma";
Signature · 7 lines
2.20.1 _______________________________________________ linux-arm-kernel mailing list [email protected] http://lists.infradead.org/mailman/listinfo/linux-arm-kernel