NXP DSPI bugfixes and support for LS1028A
Subsystems (4)
Vladimir Oltean
maintainerv2 cover NXP DSPI bugfixes and support for LS1028A
This series addresses a few issues that were missed during the previous series "[PATCH 00/12] TCFQ to XSPI migration for NXP DSPI driver", on SoCs other than LS1021A and LS1043A. DMA mode has been completely broken by that series, and XSPI mode never worked on little-endian controllers.
Then it introduces support for the LS1028A chip, whose compatible has recently been documented here:
https://lore.kernel.org/linux-devicetree/[email protected]/
The device tree for the LS1028A SoC is extended with DMA channels definition, such that even though the default operating mode is XSPI, one can simply change DSPI_XSPI_MODE to DSPI_DMA_MODE in the devtype_data structure of the driver and use that instead.
For testing, benchmarking and debugging, the mikroBUS connector on the LS1028A-RDB is made available via spidev.
Vladimir Oltean (6):
spi: spi-fsl-dspi: Don't access reserved fields in SPI_MCR
spi: spi-fsl-dspi: Fix little endian access to PUSHR CMD and TXDATA
spi: spi-fsl-dspi: Fix oper_word_size of zero for DMA mode
spi: spi-fsl-dspi: Add support for LS1028A
arm64: dts: ls1028a: Specify the DMA channels for the DSPI controllers
arm64: dts: ls1028a-rdb: Add a spidev node for the mikroBUS
.../boot/dts/freescale/fsl-ls1028a-rdb.dts | 14 ++++++ .../arm64/boot/dts/freescale/fsl-ls1028a.dtsi | 6 +++ drivers/spi/spi-fsl-dspi.c | 50 +++++++++++++++---- 3 files changed, 60 insertions(+), 10 deletions(-)
Signature · 1 line
2.17.1
Vladimir Oltean
maintainerPATCH v2 1/6 spi: spi-fsl-dspi: Don't access reserved fields in SPI_MCR
From: Vladimir Oltean <[email protected]>
The SPI_MCR_PCSIS macro assumes that the controller has a number of chip select signals equal to 6. That is not always the case, but actually is described through the driver-specific "spi-num-chipselects" device tree binding. LS1028A for example only has 4 chip selects.
Don't write to the upper bits of the PCSIS field, which are reserved in the reference manual.
---
Changes in v2:
Remove duplicate phrase in commit message.
drivers/spi/spi-fsl-dspi.c | 7 +++++-- 1 file changed, 5 insertions(+), 2 deletions(-)
drivers/spi/spi-fsl-dspi.c +5 -2
@@ -22,7 +22,7 @@#define SPI_MCR 0x00#define SPI_MCR_MASTER BIT(31) -#define SPI_MCR_PCSIS (0x3F << 16) +#define SPI_MCR_PCSIS (x) ((x) << 16)#define SPI_MCR_CLR_TXF BIT(11)#define SPI_MCR_CLR_RXF BIT(10)#define SPI_MCR_XSPI BIT(3)
@@ -1197,7 +1197,10 @@ static const struct regmap_config dspi_xspi_regmap_config[] = {static void dspi_init (struct fsl_dspi *dspi) { -unsigned int mcr =SPI_MCR_PCSIS ; +unsigned int mcr; + +/* Set idle states for all chip select signals to high */ + mcr =SPI_MCR_PCSIS (GENMASK (dspi->ctlr->num_chipselect -1 ,0 ));if (dspi->devtype_data->trans_mode ==DSPI_XSPI_MODE ) mcr |=SPI_MCR_XSPI ;
Signature · 1 line
2.17.1
Vladimir Oltean
maintainerPATCH v2 2/6 spi: spi-fsl-dspi: Fix little endian access to PUSHR CMD and TXDATA
In reply to Vladimir OlteanFrom: Vladimir Oltean <[email protected]>
In XSPI mode, the 32-bit PUSHR register can be written to separately:
the higher 16 bits are for commands and the lower 16 bits are for data.
This has nicely been hacked around, by defining a second regmap with a width of 16 bits, and effectively splitting a 32-bit register into 2 16-bit ones, from the perspective of this regmap_pushr.
The problem is the assumption about the controller's endianness. If the controller is little endian (such as anything post-LS1046A), then the first 2 bytes, in the order imposed by memory layout, will actually hold the TXDATA, and the last 2 bytes will hold the CMD.
So take the controller's endianness into account when performing split writes to PUSHR. The obvious and simple solution would have been to call regmap_get_val_endian(), but that is an internal regmap function and we don't want to change regmap just for this. Therefore, we just re-read the "big-endian" device tree property.
---
Changes in v2:
Parse "big-endian" device tree bindings instead of taking the decision based on compatible SoC.
drivers/spi/spi-fsl-dspi.c | 26 ++++++++++++++++++++------ 1 file changed, 20 insertions(+), 6 deletions(-)
drivers/spi/spi-fsl-dspi.c +20 -6
@@ -103,10 +103,6 @@#define SPI_FRAME_BITS (bits) SPI_CTAR_FMSZ((bits) - 1)#define SPI_FRAME_EBITS (bits) SPI_CTARE_FMSZE(((bits) - 1) >> 4) -/* Register offsets for regmap_pushr */ -#define PUSHR_CMD 0x0 -#define PUSHR_TX 0x2 -#define DMA_COMPLETION_TIMEOUT msecs_to_jiffies(3000)struct chip_data {
@@ -240,6 +236,13 @@ struct fsl_dspi {int words_in_flight; +/* +* Offsets for CMD and TXDATA within SPI_PUSHR when accessed +* individually (in XSPI mode) +*/ +int pushr_cmd; +int pushr_tx; +void (*host_to_dev)(struct fsl_dspi *dspi,u32 *txdata);void (*dev_to_host)(struct fsl_dspi *dspi,u32 rxdata); };
@@ -670,12 +673,12 @@ static void dspi_pushr_cmd_write(struct fsl_dspi *dspi, u16 cmd)*/ if (dspi->len > dspi->oper_word_size) cmd |=SPI_PUSHR_CMD_CONT ; -regmap_write (dspi->regmap_pushr,PUSHR_CMD , cmd); +regmap_write (dspi->regmap_pushr, dspi->pushr_cmd, cmd); }static void dspi_pushr_txdata_write (struct fsl_dspi *dspi,u16 txdata) { -regmap_write (dspi->regmap_pushr,PUSHR_TX , txdata); +regmap_write (dspi->regmap_pushr, dspi->pushr_tx, txdata); }static void dspi_xspi_write (struct fsl_dspi *dspi,int cnt,bool eoq)
@@ -1256,6 +1259,7 @@ static int dspi_probe(struct platform_device *pdev)struct fsl_dspi *dspi;struct resource *res;void __iomem *base; +bool big_endian; ctlr =spi_alloc_master (&pdev->dev,sizeof (struct fsl_dspi ));if (!ctlr)
@@ -1281,6 +1285,7 @@ static int dspi_probe(struct platform_device *pdev)/* Only Coldfire uses platform data */ dspi->devtype_data = &devtype_data[MCF5441X ]; + big_endian = true; }else { ret =of_property_read_u32 (np,"spi-num-chipselects" , &cs_num);
@@ -1302,6 +1307,15 @@ static int dspi_probe(struct platform_device *pdev) ret = -EFAULT ; goto out_ctlr_put; } + + big_endian =of_device_is_big_endian (np); + } +if (big_endian) { + dspi->pushr_cmd =0 ; + dspi->pushr_tx =2 ; + }else { + dspi->pushr_cmd =2 ; + dspi->pushr_tx =0 ; }if (dspi->devtype_data->trans_mode ==DSPI_XSPI_MODE )
Signature · 1 line
2.17.1
Vladimir Oltean
maintainerPATCH v2 3/6 spi: spi-fsl-dspi: Fix oper_word_size of zero for DMA mode
In reply to Vladimir OlteanFrom: Vladimir Oltean <[email protected]>
In DMA mode, dspi_setup_accel does not get called, which results in the dspi->oper_word_size variable (which is used by dspi_dma_xfer) to not be initialized properly.
Because oper_word_size is zero, a few calculations end up being incorrect, and the DMA transfer eventually times out instead of sending anything on the wire.
Set up native transfers (or 8-on-16 acceleration) using dspi_setup_accel for DMA mode too.
---
Changes in v2:
None.
drivers/spi/spi-fsl-dspi.c | 7 +++++-- 1 file changed, 5 insertions(+), 2 deletions(-)
drivers/spi/spi-fsl-dspi.c +5 -2
@@ -359,6 +359,8 @@ static void dspi_rx_dma_callback(void *arg)complete (&dma->cmd_rx_complete); } +static void dspi_setup_accel (struct fsl_dspi *dspi); +static int dspi_next_xfer_dma_submit (struct fsl_dspi *dspi) {struct device *dev = &dspi->pdev->dev;
@@ -446,9 +448,10 @@ static int dspi_dma_xfer(struct fsl_dspi *dspi)int bytes_per_buffer;int ret =0 ; +dspi_setup_accel (dspi); + curr_remaining_bytes = dspi->len; - bytes_per_buffer = dspi->devtype_data->dma_bufsize / - dspi->devtype_data->fifo_size; + bytes_per_buffer = dspi->devtype_data->dma_bufsize;while (curr_remaining_bytes) {/* Check if current transfer fits the DMA buffer */ dma->curr_xfer_len = curr_remaining_bytes /
Signature · 1 line
2.17.1
Vladimir Oltean
maintainerPATCH v2 4/6 spi: spi-fsl-dspi: Add support for LS1028A
In reply to Vladimir OlteanFrom: Vladimir Oltean <[email protected]>
This is similar to the DSPI instantiation on LS1028A, except that:
- The A-011218 erratum has been fixed, so DMA works
- The endianness is different, which has implications on XSPI mode
Some benchmarking with the following command:
spidev_test --device /dev/spidev2.0 --bpw 8 --size 256 --cpha --iter 10000000 --speed 20000000
shows that in DMA mode, it can achieve around 2400 kbps, and in XSPI mode, the same command goes up to 4700 kbps. This is somewhat to be expected, since the DMA buffer size is extremely small at 8 bytes, the winner becomes whomever can prepare the buffers for transmission quicker, and DMA mode has higher overhead there. So XSPI FIFO mode has been chosen as the operating mode for this chip.
---
Changes in v2:
Switch to DSPI_XSPI_MODE.
drivers/spi/spi-fsl-dspi.c | 10 ++++++++++ 1 file changed, 10 insertions(+)
drivers/spi/spi-fsl-dspi.c +10 -0
@@ -125,6 +125,7 @@ struct fsl_dspi_devtype_data {enum {LS1021A ,LS1012A , +LS1028A ,LS1043A ,LS1046A ,LS2080A ,
@@ -153,6 +154,12 @@ static const struct fsl_dspi_devtype_data devtype_data[] = { .max_clock_factor = 8, .fifo_size = 16, }, + [LS1028A] = { + .trans_mode = DSPI_XSPI_MODE, + .dma_bufsize = 8, + .max_clock_factor = 8, + .fifo_size = 4, + }, [LS1043A] = {/* Has A-011218 DMA erratum */ .trans_mode = DSPI_XSPI_MODE,
@@ -1100,6 +1107,9 @@ static const struct of_device_id fsl_dspi_dt_ids[] = { }, { .compatible = "fsl,ls1012a-dspi", .data = &devtype_data[LS1012A], + }, { + .compatible = "fsl,ls1028a-dspi", + .data = &devtype_data[LS1028A], }, { .compatible = "fsl,ls1043a-dspi", .data = &devtype_data[LS1043A],
Signature · 1 line
2.17.1
Vladimir Oltean
maintainerPATCH v2 5/6 arm64: dts: ls1028a: Specify the DMA channels for the DSPI controllers
In reply to Vladimir OlteanFrom: Vladimir Oltean <[email protected]>
LS1028A has a functional connection to the eDMA module. Even if the spi-fsl-dspi.c driver is not using DMA for LS1028A now, define the slots in the DMAMUX for connecting the eDMA channels to the 3 DSPI controllers.
---
Changes in v2:
None.
arch/arm64/boot/dts/freescale/fsl-ls1028a.dtsi | 6 ++++++ 1 file changed, 6 insertions(+)
arch/arm64/boot/dts/freescale/fsl-ls1028a.dtsi +6 -0
@@ -298,6 +298,8 @@ interrupts = <GIC_SPI 26 IRQ_TYPE_LEVEL_HIGH>; clock-names = "dspi"; clocks = <&clockgen 4 1>; + dmas = <&edma0 0 62>, <&edma0 0 60>; + dma-names = "tx", "rx"; spi-num-chipselects = <4>; little-endian; status = "disabled";
@@ -311,6 +313,8 @@ interrupts = <GIC_SPI 26 IRQ_TYPE_LEVEL_HIGH>; clock-names = "dspi"; clocks = <&clockgen 4 1>; + dmas = <&edma0 0 58>, <&edma0 0 56>; + dma-names = "tx", "rx"; spi-num-chipselects = <4>; little-endian; status = "disabled";
@@ -324,6 +328,8 @@ interrupts = <GIC_SPI 26 IRQ_TYPE_LEVEL_HIGH>; clock-names = "dspi"; clocks = <&clockgen 4 1>; + dmas = <&edma0 0 54>, <&edma0 0 2>; + dma-names = "tx", "rx"; spi-num-chipselects = <3>; little-endian; status = "disabled";
Signature · 1 line
2.17.1
Vladimir Oltean
maintainerPATCH v2 6/6 arm64: dts: ls1028a-rdb: Add a spidev node for the mikroBUS
In reply to Vladimir OlteanFrom: Vladimir Oltean <[email protected]>
For debugging, it is useful to have access to the DSPI controller signals. On the reference design board, these are exported to either the mikroBUS1 or mikroBUS2 connector (according to the CPLD register BRDCFG3[SPI3]).
---
Changes in v2:
Change compatible string for spidev node.
arch/arm64/boot/dts/freescale/fsl-ls1028a-rdb.dts | 14 ++++++++++++++ 1 file changed, 14 insertions(+)
arch/arm64/boot/dts/freescale/fsl-ls1028a-rdb.dts +14 -0
@@ -83,6 +83,20 @@ }; }; +&dspi2 { + bus-num = <2>; + status = "okay"; + + /* mikroBUS1 */ + spidev@0 { + compatible = "rohm,dh2228fv"; + spi-max-frequency = <20000000>; + fsl,spi-cs-sck-delay = <100>; + fsl,spi-sck-cs-delay = <100>; + reg = <0>; + }; +}; + &esdhc { sd-uhs-sdr104; sd-uhs-sdr50;
Signature · 1 line
2.17.1
Am 2020-03-09 22:07, schrieb Vladimir Oltean:
Quoted 10 lines
This series addresses a few issues that were missed during the previous series "[PATCH 00/12] TCFQ to XSPI migration for NXP DSPI driver", on SoCs other than LS1021A and LS1043A. DMA mode has been completely broken by that series, and XSPI mode never worked on little-endian controllers.
Then it introduces support for the LS1028A chip, whose compatible has recently been documented here:
Quoted 7 lines
The device tree for the LS1028A SoC is extended with DMA channels definition, such that even though the default operating mode is XSPI, one can simply change
DSPI_XSPI_MODEtoDSPI_DMA_MODEin thedevtype_datastructure of the driver and use that instead.For testing, benchmarking and debugging, the mikroBUS connector on the LS1028A-RDB is made available via spidev.
Let me start with the positive things... something is working, both in XSPI mode and DMA mode ;) At least the SPI flash is detected.
And please note, that I have my patch applied:
https://lore.kernel.org/lkml/[email protected]/
Further note, that the mtd device is either mtd0 in XSPI mode or mtd10 in DMA mode, because the first probe fails due to EPROBE_DEFER.
So starting with XSPI, if you have a big flash and cancel the readout strange things happen.
# hexdump -C /dev/mtd0 00000000 00 75 68 75 0a ff ff ff ff ff ff ff ff ff ff ff |.uhu............| 00000010 ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff |................| * ^C[ 35.487948] fsl-dspi 2120000.spi: Waiting for transfer to complete failed! [ 35.495038] spi_master spi2: failed to transfer one message from queue
# hexdump -C /dev/mtd0 00000000 00 75 68 75 0a ff ff ff ff ff ff ff ff ff ff ff |.uhu............| 00000010 ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff |................| * ^C[ 38.495955] fsl-dspi 2120000.spi: Waiting for transfer to complete failed! [ 38.503097] spi_master spi2: failed to transfer one message from queue [ 38.509729] Unable to handle kernel paging request at virtual address ffff800095ab3377 [ 38.517676] Mem abort info: [ 38.520474] ESR = 0x96000045 [ 38.523533] EC = 0x25: DABT (current EL), IL = 32 bits [ 38.528861] SET = 0, FnV = 0 [ 38.531921] EA = 0, S1PTW = 0 [ 38.535067] Data abort info: [ 38.537952] ISV = 0, ISS = 0x00000045 [ 38.541797] CM = 0, WnR = 1 [ 38.544771] swapper pgtable: 4k pages, 48-bit VAs, pgdp=0000000082621000 [ 38.551494] [ffff800095ab3377] pgd=00000020fffff003, p4d=00000020fffff003, pud=0000000000000000 [ 38.560229] Internal error: Oops: 96000045 [#1] PREEMPT SMP [ 38.565819] Modules linked in: [ 38.568882] CPU: 0 PID: 2729 Comm: hexdump Not tainted 5.6.0-rc4-next-20200306-00052-gd8730cdc8a0b-dirty #193 [ 38.578834] Hardware name: Kontron SMARC-sAL28 (Single PHY) on SMARC Eval 2.0 carrier (DT) [ 38.587129] pstate: 20000085 (nzCv daIf -PAN -UAO) [ 38.591941] pc : ktime_get_real_ts64+0x3c/0x110 [ 38.596487] lr : spi_take_timestamp_pre+0x40/0x90 [ 38.601203] sp : ffff800010003d90 [ 38.604525] x29: ffff800010003d90 x28: ffff80001200e000 [ 38.609854] x27: ffff800011da9000 x26: ffff002079c40400 [ 38.615184] x25: ffff8000117fe018 x24: ffff800011daa1a0 [ 38.620513] x23: ffff800015ab3860 x22: ffff800095ab3377 [ 38.625841] x21: 000000000000146e x20: ffff8000120c3000 [ 38.631170] x19: ffff0020795f6e80 x18: ffff800011da9948 [ 38.636498] x17: 0000000000000000 x16: 0000000000000000 [ 38.641826] x15: ffff800095ab3377 x14: 0720072007200720 [ 38.647155] x13: 0720072007200765 x12: 0775076507750771 [ 38.652483] x11: 0720076d076f0772 x10: 0000000000000040 [ 38.657812] x9 : ffff8000108e2100 x8 : ffff800011dcabe8 [ 38.663139] x7 : 0000000000000000 x6 : ffff800015ab3a60 [ 38.668468] x5 : 0000000007200720 x4 : ffff800095ab3377 [ 38.673796] x3 : 0000000000000000 x2 : 0000000000000ab0 [ 38.679125] x1 : ffff800011daa000 x0 : 0000000000000026 [ 38.684454] Call trace: [ 38.686905] ktime_get_real_ts64+0x3c/0x110 [ 38.691100] spi_take_timestamp_pre+0x40/0x90 [ 38.695470] dspi_fifo_write+0x58/0x2c0 [ 38.699315] dspi_interrupt+0xbc/0xd0 [ 38.702987] __handle_irq_event_percpu+0x78/0x2c0 [ 38.707706] handle_irq_event_percpu+0x3c/0x90 [ 38.712161] handle_irq_event+0x4c/0xd0 [ 38.716008] handle_fasteoi_irq+0xbc/0x170 [ 38.720115] generic_handle_irq+0x2c/0x40 [ 38.724135] __handle_domain_irq+0x68/0xc0 [ 38.728243] gic_handle_irq+0xc8/0x160 [ 38.732000] el1_irq+0xb8/0x180 [ 38.735149] spi_nor_spimem_read_data+0xe0/0x140 [ 38.739779] spi_nor_read+0xc4/0x120 [ 38.743364] mtd_read_oob+0xa8/0xc0 [ 38.746860] mtd_read+0x4c/0x80 [ 38.750007] mtdchar_read+0x108/0x2a0 [ 38.753679] __vfs_read+0x20/0x50 [ 38.757002] vfs_read+0xa4/0x190 [ 38.760237] ksys_read+0x6c/0xf0 [ 38.763471] __arm64_sys_read+0x20/0x30 [ 38.767319] el0_svc_common.constprop.3+0x90/0x160 [ 38.772125] do_el0_svc+0x28/0x90 [ 38.775449] el0_sync_handler+0x118/0x190 [ 38.779468] el0_sync+0x140/0x180 [ 38.782793] Code: 91000294 1400000f d50339bf f9405e80 (f90002c0) [ 38.788910] ---[ end trace 55da560db4d6bef7 ]--- [ 38.793540] Kernel panic - not syncing: Fatal exception in interrupt [ 38.799914] SMP: stopping secondary CPUs [ 38.803849] Kernel Offset: disabled [ 38.807344] CPU features: 0x10002,20006008 [ 38.811451] Memory Limit: none [ 38.814513] ---[ end Kernel panic - not syncing: Fatal exception in interrupt ]---
In DMA mode one byte writes seem to work. But at least 5 byte writes do not:
# echo -ne '\x00' > /dev/mtd10 # echo 'huhu' > /dev/mtd10 [ 34.275383] fsl-dspi 2120000.spi: DMA tx timeout [ 34.280035] fsl-dspi 2120000.spi: DMA transfer failed [ 34.285116] fsl-dspi 2120000.spi: Waiting for transfer to complete failed! [ 34.292029] spi_master spi2: failed to transfer one message from queue sh: write error: Connection timed out #
Vladimir, what kind of SPI device do you have to test?
-michael
Quoted 14 lines
Vladimir Oltean (6):
spi: spi-fsl-dspi: Don't access reserved fields inSPI_MCR
spi: spi-fsl-dspi: Fix little endian access to PUSHR CMD and TXDATA
spi: spi-fsl-dspi: Fixoper_word_sizeof zero for DMA mode
spi: spi-fsl-dspi: Add support for LS1028A
arm64: dts: ls1028a: Specify the DMA channels for the DSPI
controllers
arm64: dts: ls1028a-rdb: Add a spidev node for the mikroBUS.../boot/dts/freescale/fsl-ls1028a-rdb.dts | 14 ++++++ .../arm64/boot/dts/freescale/fsl-ls1028a.dtsi | 6 +++ drivers/spi/spi-fsl-dspi.c | 50 +++++++++++++++---- 3 files changed, 60 insertions(+), 10 deletions(-)
Vladimir Oltean
maintainerQuoted 5 lines · Michael Walle
So starting with XSPI, if you have a big flash and cancel the readout strange things happen.
Quoted 11 lines
# hexdump -C /dev/mtd0 00000000 00 75 68 75 0a ff ff ff ff ff ff ff ff ff ff ff |.uhu............| 00000010 ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff |................| * ^C[ 35.487948] fsl-dspi 2120000.spi: Waiting for transfer to complete failed! [ 35.495038] spi_master spi2: failed to transfer one message from queue
This, I think, is expected.
Quoted 76 lines
# hexdump -C /dev/mtd0 00000000 00 75 68 75 0a ff ff ff ff ff ff ff ff ff ff ff |.uhu............| 00000010 ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff |................| * ^C[ 38.495955] fsl-dspi 2120000.spi: Waiting for transfer to complete failed! [ 38.503097] spi_master spi2: failed to transfer one message from queue [ 38.509729] Unable to handle kernel paging request at virtual address ffff800095ab3377 [ 38.517676] Mem abort info: [ 38.520474] ESR = 0x96000045 [ 38.523533] EC = 0x25: DABT (current EL), IL = 32 bits [ 38.528861] SET = 0, FnV = 0 [ 38.531921] EA = 0, S1PTW = 0 [ 38.535067] Data abort info: [ 38.537952] ISV = 0, ISS = 0x00000045 [ 38.541797] CM = 0, WnR = 1 [ 38.544771] swapper pgtable: 4k pages, 48-bit VAs, pgdp=0000000082621000 [ 38.551494] [ffff800095ab3377] pgd=00000020fffff003, p4d=00000020fffff003, pud=0000000000000000 [ 38.560229] Internal error: Oops: 96000045 [#1] PREEMPT SMP [ 38.565819] Modules linked in: [ 38.568882] CPU: 0 PID: 2729 Comm: hexdump Not tainted 5.6.0-rc4-next-20200306-00052-gd8730cdc8a0b-dirty #193 [ 38.578834] Hardware name: Kontron SMARC-sAL28 (Single PHY) on SMARC Eval 2.0 carrier (DT) [ 38.587129] pstate: 20000085 (nzCv daIf -PAN -UAO) [ 38.591941] pc : ktime_get_real_ts64+0x3c/0x110 [ 38.596487] lr : spi_take_timestamp_pre+0x40/0x90 [ 38.601203] sp : ffff800010003d90 [ 38.604525] x29: ffff800010003d90 x28: ffff80001200e000 [ 38.609854] x27: ffff800011da9000 x26: ffff002079c40400 [ 38.615184] x25: ffff8000117fe018 x24: ffff800011daa1a0 [ 38.620513] x23: ffff800015ab3860 x22: ffff800095ab3377 [ 38.625841] x21: 000000000000146e x20: ffff8000120c3000 [ 38.631170] x19: ffff0020795f6e80 x18: ffff800011da9948 [ 38.636498] x17: 0000000000000000 x16: 0000000000000000 [ 38.641826] x15: ffff800095ab3377 x14: 0720072007200720 [ 38.647155] x13: 0720072007200765 x12: 0775076507750771 [ 38.652483] x11: 0720076d076f0772 x10: 0000000000000040 [ 38.657812] x9 : ffff8000108e2100 x8 : ffff800011dcabe8 [ 38.663139] x7 : 0000000000000000 x6 : ffff800015ab3a60 [ 38.668468] x5 : 0000000007200720 x4 : ffff800095ab3377 [ 38.673796] x3 : 0000000000000000 x2 : 0000000000000ab0 [ 38.679125] x1 : ffff800011daa000 x0 : 0000000000000026 [ 38.684454] Call trace: [ 38.686905] ktime_get_real_ts64+0x3c/0x110 [ 38.691100] spi_take_timestamp_pre+0x40/0x90 [ 38.695470] dspi_fifo_write+0x58/0x2c0 [ 38.699315] dspi_interrupt+0xbc/0xd0 [ 38.702987] __handle_irq_event_percpu+0x78/0x2c0 [ 38.707706] handle_irq_event_percpu+0x3c/0x90 [ 38.712161] handle_irq_event+0x4c/0xd0 [ 38.716008] handle_fasteoi_irq+0xbc/0x170 [ 38.720115] generic_handle_irq+0x2c/0x40 [ 38.724135] __handle_domain_irq+0x68/0xc0 [ 38.728243] gic_handle_irq+0xc8/0x160 [ 38.732000] el1_irq+0xb8/0x180 [ 38.735149] spi_nor_spimem_read_data+0xe0/0x140 [ 38.739779] spi_nor_read+0xc4/0x120 [ 38.743364] mtd_read_oob+0xa8/0xc0 [ 38.746860] mtd_read+0x4c/0x80 [ 38.750007] mtdchar_read+0x108/0x2a0 [ 38.753679] __vfs_read+0x20/0x50 [ 38.757002] vfs_read+0xa4/0x190 [ 38.760237] ksys_read+0x6c/0xf0 [ 38.763471] __arm64_sys_read+0x20/0x30 [ 38.767319] el0_svc_common.constprop.3+0x90/0x160 [ 38.772125] do_el0_svc+0x28/0x90 [ 38.775449] el0_sync_handler+0x118/0x190 [ 38.779468] el0_sync+0x140/0x180 [ 38.782793] Code: 91000294 1400000f d50339bf f9405e80 (f90002c0)
Quoted 9 lines
[ 38.788910] ---[ end trace 55da560db4d6bef7 ]--- [ 38.793540] Kernel panic - not syncing: Fatal exception in interrupt [ 38.799914] SMP: stopping secondary CPUs [ 38.803849] Kernel Offset: disabled [ 38.807344] CPU features: 0x10002,20006008 [ 38.811451] Memory Limit: none [ 38.814513] ---[ end Kernel panic - not syncing: Fatal exception in interrupt ]---
And this, I think, isn't. I've sent a new patch that addresses this in v3, although it's always been like this as far as I can tell.
Quoted 5 lines
In DMA mode one byte writes seem to work. But at least 5 byte writes do not:
Quoted 11 lines
# echo -ne '\x00' > /dev/mtd10 # echo 'huhu' > /dev/mtd10 [ 34.275383] fsl-dspi 2120000.spi: DMA tx timeout [ 34.280035] fsl-dspi 2120000.spi: DMA transfer failed [ 34.285116] fsl-dspi 2120000.spi: Waiting for transfer to complete failed! [ 34.292029] spi_master spi2: failed to transfer one message from queue sh: write error: Connection timed out #
Correct, thanks for pointing out. Fixed this in v3.
Quoted 4 lines
Vladimir, what kind of SPI device do you have to test?
-michael
spidev_test --input <file-generated-with-hex-editor> and watch the output with a protocol analyzer.
Thanks,
-Vladimir