Input: goodix - Try to reset the controller if the i2c-test fails
Subsystems (3)
cover Input: goodix - Try to reset the controller if the i2c-test fails
Hi,
Here is a small patch fixing the goodix touchscreen driver failing at probe due to what I consider a BIOS bug on Dmitry's Mastykin's tablet.
This patch applies on top of my earlier series starting with:
[PATCH v3 01/11] Input: goodix - Refactor IRQ pin GPIO accesses
Regards,
Hans
PATCH 1/1 Input: goodix - Try to reset the controller if the i2c-test fails
On some ACPI/x86 devices (where we use one of the ACPI IRQ pin access methods) the firmware is buggy, it does not properly reset the controller at boot, and we cannot communicate with it.
Normally on ACPI/x86 devices we do not want to reset the controller at probe time since in some cases this causes the controller to loose its configuration and this is loaded into it by the system's firmware. So on these systems we leave the reset_controller_at_probe flag unset, even though we have a access to both the IRQ and reset pins and thus could reset it.
In the case of the buggy firmware we have to reset the controller to actually be able to talk to it.
This commit adds a special case for this, if the goodix_i2c_test() fails, and we have not reset the controller yet; and we do have a way to reset the controller then retry the i2c-test after resetting the controller.
This fixes the driver failing at probe on ACPI/x86 systems with this firmware bug.
--- drivers/input/touchscreen/goodix.c | 7 +++++++ 1 file changed, 7 insertions(+)
drivers/input/touchscreen/goodix.c +7 -0
@@ -1165,6 +1165,7 @@ static int goodix_ts_probe(struct i2c_client *client,if (error)return error; +reset:if (ts->reset_controller_at_probe) {/* reset the controller */ error =goodix_reset (ts);
@@ -1176,6 +1177,12 @@ static int goodix_ts_probe(struct i2c_client *client, error =goodix_i2c_test (client);if (error) { +if (!ts->reset_controller_at_probe && + ts->irq_pin_access_method !=IRQ_PIN_ACCESS_NONE ) { +/* Retry after a controller reset */ + ts->reset_controller_at_probe = true; + goto reset; + }dev_err (&client->dev,"I2C communication failure: %d\n" , error);return error; }
Signature · 1 line
2.25.1
Quoted 18 lines · Hans de Goede
On some ACPI/x86 devices (where we use one of the ACPI IRQ pin access methods) the firmware is buggy, it does not properly reset the controller at boot, and we cannot communicate with it.
Normally on ACPI/x86 devices we do not want to reset the controller at probe time since in some cases this causes the controller to loose its configuration and this is loaded into it by the system's firmware. So on these systems we leave the
reset_controller_at_probeflag unset, even though we have a access to both the IRQ and reset pins and thus could reset it.In the case of the buggy firmware we have to reset the controller to actually be able to talk to it.
This commit adds a special case for this, if the
goodix_i2c_test()fails, and we have not reset the controller yet; and we do have a way to reset the controller then retry the i2c-test after resetting the controller.
Quoted 5 lines
This fixes the driver failing at probe on ACPI/x86 systems with this firmware bug.
Reported-and-tested-by Dmitry Mastykin <[email protected]>Signed-off-by Hans de Goede <[email protected]>
Applied, thank you.
Quoted 32 lines
--- drivers/input/touchscreen/goodix.c | 7 +++++++ 1 file changed, 7 insertions(+)drivers/input/touchscreen/goodix.c +7
-0@@ -1165,6 +1165,7 @@ static int goodix_ts_probe(struct i2c_client *client,if (error)return error; +reset:if (ts->reset_controller_at_probe) {/* reset the controller */ error =goodix_reset (ts);@@ -1176,6 +1177,12 @@ static int goodix_ts_probe(struct i2c_client *client, error =goodix_i2c_test (client);if (error) { +if (!ts->reset_controller_at_probe && + ts->irq_pin_access_method !=IRQ_PIN_ACCESS_NONE ) { +/* Retry after a controller reset */ + ts->reset_controller_at_probe = true; + goto reset; + }dev_err (&client->dev,"I2C communication failure: %d\n" , error);return error; }Signature · 1 line
2.25.1
Signature · 1 line
Dmitry