dt-bindings: arm: fsl: add nxp based toradex colibri bindings
Subsystems (3)
PATCH v5 1/2 dt-bindings: arm: fsl: add nxp based toradex colibri bindings
From: Igor Opaniuk <[email protected]>
Document Colibri iMX6S/DL V1.1x re-design devicetree binding.
---
Documentation/devicetree/bindings/arm/fsl.yaml | 2 ++ 1 file changed, 2 insertions(+)
Documentation/devicetree/bindings/arm/fsl.yaml +2 -0
@@ -169,7 +169,9 @@ properties: - technologic,imx6dl-ts4900 - technologic,imx6dl-ts7970 - toradex,colibri_imx6dl # Colibri iMX6 Module + - toradex,colibri_imx6dl-v1_1 # Colibri iMX6 Module V1.1 - toradex,colibri_imx6dl-eval-v3 # Colibri iMX6 Module on Colibri Evaluation Board V3 + - toradex,colibri_imx6dl-v1_1-eval-v3 # Colibri iMX6 Module V1.1 on Colibri Evaluation Board V3 - ysoft,imx6dl-yapp4-draco # i.MX6 DualLite Y Soft IOTA Draco board - ysoft,imx6dl-yapp4-hydra # i.MX6 DualLite Y Soft IOTA Hydra board - ysoft,imx6dl-yapp4-ursa # i.MX6 Solo Y Soft IOTA Ursa board
Signature · 1 line
2.17.1
PATCH v5 2/2 ARM: dts: colibri: introduce device trees with UHS-I support
From: Igor Opaniuk <[email protected]>
1. Introduce dtsi with overlay configuration for enabling UHS-I for Colibri iMX6S/DL V1.1x re-design.
2. Introduce new dts for the Colibri iMX6S/DL V1.1x
on Colibri Evaluation Carrier Board V3.x. However, disable 1.8V for the Colibri Evaluation Board since this carrier board has 3.3V pull-ups on.
3. Provide proper configuration for VGEN3, which allows that rail to be automatically switched to 1.8 volts for proper UHS-I operation mode.
---
v5:
- Fix copyright/licensing [Shawn Guo]
- Don't enable 1.8V by default, as some carrier boards have 3.3V pull-ups, which leads to [ 164.058099] mmc0: error -110 whilst initialising SD card errors. [Marcel Ziswiler]
- Change hierarchy: move SD-card properties to the module level device tree include (to explicitly state that these properties relate to module, not carrier board) + people can easily include it in their custom carrier board device trees.
v4:
- Document Colibri iMX6S/DL V1.1x re-design devicetree binding [Shawn Guo]
- wakeup-source property fix [Shawn Guo]
v3:
- change hierarchy according to Marco's suggestions [Marco Felsch]
- adjust compatible string adding v1.1 [Stefan Agner]
v2:
- rework hierarchy of dts files, and a separate dtsi for Colibri iMX6S/DL V1.1x re-design, where UHS-I was added [Marcel Ziswiler]
- add comments about vgen3 power rail [Marcel Ziswiler]
- fix other minor issues, addressing Marcel's comments. [Marcel Ziswiler]
arch/arm/boot/dts/Makefile | 1 + .../boot/dts/imx6dl-colibri-v1_1-eval-v3.dts | 31 +++++++++++++ .../boot/dts/imx6qdl-colibri-v1_1-uhs.dtsi | 44 +++++++++++++++++++ arch/arm/boot/dts/imx6qdl-colibri.dtsi | 11 ++++- 4 files changed, 86 insertions(+), 1 deletion(-) create mode 100644 arch/arm/boot/dts/imx6dl-colibri-v1_1-eval-v3.dts create mode 100644 arch/arm/boot/dts/imx6qdl-colibri-v1_1-uhs.dtsi
arch/arm/boot/dts/Makefile +1 -0
@@ -412,6 +412,7 @@ dtb-$(CONFIG_SOC_IMX6Q) += \ imx6dl-aristainetos2_4.dtb \ imx6dl-aristainetos2_7.dtb \ imx6dl-colibri-eval-v3.dtb \ + imx6dl-colibri-v1_1-eval-v3.dtb \ imx6dl-cubox-i.dtb \ imx6dl-cubox-i-emmc-som-v15.dtb \ imx6dl-cubox-i-som-v15.dtb \
arch/arm/boot/dts/imx6dl-colibri-v1_1-eval-v3.dts new file +31 -0
@@ -0,0 +1,31 @@ +// SPDX-License-Identifier: GPL-2.0+ OR MIT +/* + * Copyright 2020 Toradex + */ + +/dts-v1/; + +#include "imx6dl-colibri-eval-v3.dts" +#include "imx6qdl-colibri-v1_1-uhs.dtsi" + +/ { + model = "Toradex Colibri iMX6DL/S V1.1 on Colibri Evaluation Board V3"; + compatible = "toradex,colibri_imx6dl-v1_1-eval-v3", + "toradex,colibri_imx6dl-v1_1", + "toradex,colibri_imx6dl-eval-v3", + "toradex,colibri_imx6dl", + "fsl,imx6dl"; +}; + +/* Colibri MMC */ +&usdhc1 { + status = "okay"; + /* + * Please make sure your carrier board does not pull-up any of + * the MMC/SD signals to 3.3 volt before attempting to activate + * UHS-I support. + * To let signaling voltage be changed to 1.8V, please + * delete no-1-8-v property (example below): + * /delete-property/no-1-8-v; + */ +};
arch/arm/boot/dts/imx6qdl-colibri-v1_1-uhs.dtsi new file +44 -0
44 lines not on this page · raw message
arch/arm/boot/dts/imx6qdl-colibri.dtsi +10 -1
@@ -229,7 +229,16 @@ regulator-always-on; }; - /* vgen3: unused */ + /* + * +V3.3_1.8_SD1 coming off VGEN3 and supplying + * the i.MX 6 NVCC_SD1. + */ + vgen3_reg: vgen3 { + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <3300000>; + regulator-boot-on; + regulator-always-on; + }; vgen4_reg: vgen4 { regulator-min-microvolt = <1800000>;
Signature · 1 line
2.17.1
Quoted 10 lines · Igor Opaniuk
From: Igor Opaniuk <[email protected]>
Document Colibri iMX6S/DL V1.1x re-design devicetree binding.
Signed-off-by Igor Opaniuk <[email protected]>---
Documentation/devicetree/bindings/arm/fsl.yaml | 2 ++ 1 file changed, 2 insertions(+)
Shawn Guo
AppliedQuoted 5 lines · Igor Opaniuk
From: Igor Opaniuk <[email protected]>
Document Colibri iMX6S/DL V1.1x re-design devicetree binding.
Signed-off-by Igor Opaniuk <[email protected]>
Applied both, thanks.
_______________________________________________
linux-arm-kernel mailing list
[email protected]
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel