Skip to contentSkip to conversation

arm64: dts: rockchip: Add Hugsun X99 IR receiver and power led

PATCH Applied Vivek Unune 2 participants 3 messages Mar 13, 2020 – Mar 17, 2020

Subsystems (2)
lore
Share & tools
lore
#0 lore raw

PATCH v2 1/1 arm64: dts: rockchip: Add Hugsun X99 IR receiver and power led

- Add Hugsun X99 IR receiver and power led
- Remove pwm0 node as it interferes with power LED gpio pwm0 is not used in factory firmware as well

Tested with LibreElec linux-next-20200305

---
Changes in v2:
- Changed led trigger from none to default-on
- Changed led node name from power-led to led-0

---
 .../boot/dts/rockchip/rk3399-hugsun-x99.dts   | 37 +++++++++++++++++--
 1 file changed, 33 insertions(+), 4 deletions(-)
arch/arm64/boot/dts/rockchip/rk3399-hugsun-x99.dts +32 -4
index d69a613fb65a..df425e164a2e 100644
@@ -29,6 +29,26 @@
 		regulator-max-microvolt = <5000000>;
 	};
 
+	ir-receiver {
+		compatible = "gpio-ir-receiver";
+		gpios = <&gpio0 RK_PA6 GPIO_ACTIVE_LOW>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&ir_rx>;
+	};
+
+	leds {
+		compatible = "gpio-leds";
+		pinctrl-names = "default";
+		pinctrl-0 = <&power_led_gpio>;
+
+		led-0 {
+			label = "blue:power";
+			gpios = <&gpio4 RK_PC2 GPIO_ACTIVE_HIGH>;
+			default-state = "on";
+			linux,default-trigger = "default-on";
+		};
+	};
+
 	vcc_sys: vcc-sys {
 		compatible = "regulator-fixed";
 		regulator-name = "vcc_sys";
@@ -483,6 +503,18 @@
 		};
 	};
 
+	ir {
+		ir_rx: ir-rx {
+			rockchip,pins = <0 RK_PA6 1 &pcfg_pull_none>;
+		};
+	};
+
+	leds {
+		power_led_gpio: power-led-gpio {
+			rockchip,pins = <4 RK_PC2 RK_FUNC_GPIO &pcfg_pull_none>;
+		};
+	};
+
 	pmic {
 		pmic_int_l: pmic-int-l {
 			rockchip,pins =
@@ -539,10 +572,6 @@
 	};
 };
 
-&pwm0 {
-	status = "okay";
-};
-
 &pwm2 {
 	status = "okay";
 	pinctrl-0 = <&pwm2_pin_pull_down>;
Signature · 1 line
2.20.1
maintainer Applied
#1 lore raw

Am Samstag, 14. März 2020, 00:05:13 CET schrieb Vivek Unune:

Quoted 7 lines

- Add Hugsun X99 IR receiver and power led
- Remove pwm0 node as it interferes with power LED gpio pwm0 is not used in factory firmware as well

Tested with LibreElec linux-next-20200305

I've applied this for 5.7, but did split the patch into two. One for the addition of the IR and a second for led.

Please do similar for future patches.

Thanks
Heiko

#2 lore raw
Quoted 9 lines · Heiko Stuebner

Am Samstag, 14. März 2020, 00:05:13 CET schrieb Vivek Unune:

Quoted 7 lines

- Add Hugsun X99 IR receiver and power led
- Remove pwm0 node as it interferes with power LED gpio pwm0 is not used in factory firmware as well

Tested with LibreElec linux-next-20200305

Quoted 9 lines

I've applied this for 5.7, but did split the patch into two. One for the addition of the IR and a second for led.

Please do similar for future patches.

Thanks
Heiko

Hi Heiko,

Much appriciated. I'll make sure to do that with my future patches

Thanks,

Vivek