runqemu: support multiple NICs
v4 cover runqemu: support multiple NICs
It's a re-write in comparison to v3.
Two new QB_ parameters are introduced: QB_CMDLINE_IP_SLIRP and QB_CMDLINE_IP_TAP. These parameters are by default the ip= parameters as they were previously hard-coded in runqemu. However, if, for example, more than one network interface is added to QB_NETWORK_DEVICE, the corresponding kernel parameters need to be configured accordingly.
Adrian Freihofer (1):
runqemu: support multiple NICs
meta/classes/qemuboot.bbclass | 14 ++++++++++++++ scripts/runqemu | 16 ++++++++++++---- 2 files changed, 26 insertions(+), 4 deletions(-)
Signature · 1 line
2.25.1
PATCH v4 1/1 runqemu: support multiple NICs
From: Adrian Freihofer <[email protected]>
Emulating more than one network interface with runqemu is a bit tricky, but possible. For example, the following leads to an emulated device with eth0 and eth1:
QB_NETWORK_DEVICE_prepend = " \
-device virtio-net-device,mac=52:54:00:12:34:03 \"
or
QB_NETWORK_DEVICE_append = " \
-device virtio-net-pci,mac=52:54:00:12:34:03 \"
When booting Qemu with two NICs, the kernel does not know which interface the specified ip=192.168.7.... command line argument should be applied. This delays the boot process for a very long time and a guest wihtout IP configuration.
This add two new configuraton parameters to runqemu:QB_CMDLINE_IP_SLIRP and QB_CMDLINE_IP_TAP to explicitely specify the ip= kernel command line arguments for tap and slirp mode.
Note: Simply adding "::eth0" broke some builds on the Yocto autobuilder.
--- meta/classes/qemuboot.bbclass | 14 ++++++++++++++ scripts/runqemu | 16 ++++++++++++---- 2 files changed, 26 insertions(+), 4 deletions(-)
meta/classes/qemuboot.bbclass +14 -0
@@ -36,6 +36,9 @@ # Note, runqemu will replace @MAC@ with a predefined mac, you can set # a custom one, but that may cause conflicts when multiple qemus are # running on the same host. +# Note: If more than one interface of type -device virtio-net-device gets added, +# QB_NETWORK_DEVICE_prepend might be used, since Qemu enumerates the eth* +# devices in reverse order to -device arguments. # # QB_TAP_OPT: netowrk option for 'tap' mode, e.g., # "-netdev tap,id=net0,ifname=@TAP@,script=no,downscript=no"
@@ -43,6 +46,15 @@ # # QB_SLIRP_OPT: network option for SLIRP mode, e.g., -netdev user,id=net0" # +# QB_CMDLINE_IP_SLIRP: If QB_NETWORK_DEVICE adds more than one network interface to qemu, usually the +# ip= kernel comand line argument needs to be changed accordingly. Details are documented +# in the kernel docuemntation https://www.kernel.org/doc/Documentation/filesystems/nfs/nfsroot.txt +# Example to configure only the first interface: "ip=eth0:dhcp" +# QB_CMDLINE_IP_TAP: This parameter is similar to the QB_CMDLINE_IP_SLIRP parameter. Since the tap interface requires +# static IP configuration @CLIENT@ and @GATEWAY@ place holders are replaced by the IP and the gateway +# address of the qemu guest by runqemu. +# Example: "ip=192.168.7.@CLIENT@::192.168.7.@GATEWAY@:255.255.255.0::eth0" +# # QB_ROOTFS_OPT: used as rootfs, e.g., # "-drive id=disk0,file=@ROOTFS@,if=none,format=raw -device virtio-blk-device,drive=disk0" # Note, runqemu will replace "@ROOTFS@" with the one which is used, such as core-image-minimal-qemuarm64.ext4.
@@ -63,6 +75,8 @@ QB_DEFAULT_KERNEL ?= "${KERNEL_IMAGETYPE}" QB_DEFAULT_FSTYPE ?= "ext4" QB_OPT_APPEND ?= "-show-cursor" QB_NETWORK_DEVICE ?= "-device virtio-net-pci,netdev=net0,mac=@MAC@" +QB_CMDLINE_IP_SLIRP ?= "ip=dhcp" +QB_CMDLINE_IP_TAP ?= "ip=192.168.7.@CLIENT@::192.168.7.@GATEWAY@:255.255.255.0" # This should be kept align with ROOT_VM QB_DRIVE_TYPE ?= "/dev/sd"
scripts/runqemu +12 -4
@@ -185,6 +185,8 @@ class BaseConfig(object): self.vmtypes = ('hddimg', 'iso') self.fsinfo = {} self.network_device = "-device e1000,netdev=net0,mac=@MAC@" + self.cmdline_ip_slirp = "ip=dhcp" + self.cmdline_ip_tap = "ip=192.168.7.@CLIENT@::192.168.7.@GATEWAY@:255.255.255.0" # Use different mac section for tap and slirp to avoid # conflicts, e.g., when one is running with tap, the other is # running with slirp.
@@ -1032,7 +1034,9 @@ class BaseConfig(object): if self.fstype == 'nfs': self.setup_nfs() - self.kernel_cmdline_script += ' ip=dhcp' + netconf = " " + self.cmdline_ip_slirp + logger.info("Network configuration:%s", netconf) + self.kernel_cmdline_script += netconf # Port mapping hostfwd = ",hostfwd=tcp::2222-:22,hostfwd=tcp::2323-:23" qb_slirp_opt_default = "-netdev user,id=net0%s,tftp=%s" % (hostfwd, self.get('DEPLOY_DIR_IMAGE'))
@@ -1147,9 +1151,11 @@ class BaseConfig(object): client = gateway + 1 if self.fstype == 'nfs': self.setup_nfs() - netconf = "192.168.7.%s::192.168.7.%s:255.255.255.0" % (client, gateway) - logger.info("Network configuration: %s", netconf) - self.kernel_cmdline_script += " ip=%s" % netconf + netconf = " " + self.cmdline_ip_tap + netconf = netconf.replace('@CLIENT@', str(client)) + netconf = netconf.replace('@GATEWAY@', str(gateway)) + logger.info("Network configuration:%s", netconf) + self.kernel_cmdline_script += netconf mac = "%s%02x" % (self.mac_tap, client) qb_tap_opt = self.get('QB_TAP_OPT') if qb_tap_opt:
@@ -1171,8 +1177,10 @@ class BaseConfig(object): if self.net_bridge: self.setup_net_bridge() elif self.slirp_enabled: + self.cmdline_ip_slirp = self.get('QB_CMDLINE_IP_SLIRP') or self.cmdline_ip_slirp self.setup_slirp() else: + self.cmdline_ip_tap = self.get('QB_CMDLINE_IP_TAP') or self.cmdline_ip_tap self.setup_tap() def setup_rootfs(self):
Signature · 1 line
2.25.1