Skip to contentSkip to conversation

dt-bindings: vendor-prefixes: Add Beacon vendor prefix

PATCH Applied Adam Ford 4 participants 9 messages Mar 24, 2020 – Apr 23, 2020

Subsystems (2)
lore
Share & tools
lore

Adam Ford

author
#0 lore raw

PATCH 1/2 dt-bindings: vendor-prefixes: Add Beacon vendor prefix

Beacon EmebeddedWorks is the brand owned by Compass Electronics Group, LLC based out of the United States.
https://beaconembedded.com/

Documentation/devicetree/bindings/vendor-prefixes.yaml +2 -0
index 4c8eaa11daff..7ee772b1840a 100644
@@ -141,6 +141,8 @@ patternProperties:
     description: Shenzhen AZW Technology Co., Ltd.
   "^bananapi,.*":
     description: BIPAI KEJI LIMITED
+  "^beacon,.*":
+    description: Compass Electronics Group, LLC
   "^bhf,.*":
     description: Beckhoff Automation GmbH & Co. KG
   "^bitmain,.*":
Signature · 1 line
2.25.1
author
#1 lore raw

PATCH 2/2 arm64: dts: imx: Add Beacon i.MX8m-Mini development kit

Beacon Embeddedworks is launching a development kit based on the i.MX8M Mini SoC. The kit consists of a System on Module (SOM)
+ baseboard. The SOM has the SoC, eMMC, and Ethernet. The baseboard has an wm8962 audio CODEC, a single USB OTG, and three USB host ports.

---
There will eventually be a two kits using the same baseboard, each supporting different display types, so we want to keep the baseboard file separate for now.

V3: Updated based on feedback from Fabio Estevam
V2: Updated based on feedback from Shawn Guo

arch/arm64/boot/dts/freescale/imx8mm-beacon-baseboard.dtsi new file +285 -0
new file mode 100644
index 000000000000..baa5f997d018
@@ -0,0 +1,285 @@
+// SPDX-License-Identifier: (GPL-2.0 OR MIT)
+/*
+ * Copyright 2020 Compass Electronics Group, LLC
+ */
+
+/ {
+	leds {
+		compatible = "gpio-leds";
+
+		led0 {
+			label = "gen_led0";
+			gpios = <&pca6416_1 4 GPIO_ACTIVE_HIGH>;
+			default-state = "none";
+		};
+
+		led1 {
+			label = "gen_led1";
+			gpios = <&pca6416_1 5 GPIO_ACTIVE_HIGH>;
+			default-state = "none";
+		};
+
+		led2 {
+			label = "gen_led2";
+			gpios = <&pca6416_1 6 GPIO_ACTIVE_HIGH>;
+			default-state = "none";
+		};
+
+		led3 {
+			pinctrl-names = "default";
+			pinctrl-0 = <&pinctrl_led3>;
+			label = "heartbeat";
+			gpios = <&gpio4 28 GPIO_ACTIVE_HIGH>;
+			linux,default-trigger = "heartbeat";
+		};
+	};
+
+	reg_audio: regulator-audio {
+		compatible = "regulator-fixed";
+		regulator-name = "3v3_aud";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		gpio = <&pca6416_1 11 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+	};
+
+	reg_usdhc2_vmmc: regulator-usdhc2 {
+		compatible = "regulator-fixed";
+		regulator-name = "VSD_3V3";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		gpio = <&gpio2 19 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+	};
+
+	sound {
+		compatible = "fsl,imx-audio-wm8962";
+		model = "wm8962-audio";
+		audio-cpu = <&sai3>;
+		audio-codec = <&wm8962>;
+		audio-routing =
+			"Headphone Jack", "HPOUTL",
+			"Headphone Jack", "HPOUTR",
+			"Ext Spk", "SPKOUTL",
+			"Ext Spk", "SPKOUTR",
+			"AMIC", "MICBIAS",
+			"IN3R", "AMIC";
+	};
+};
+
+&ecspi2 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_espi2>;
+	cs-gpios = <&gpio5 9 0>;
+	status = "okay";
+
+	eeprom@0 {
+		compatible = "microchip,at25160bn", "atmel,at25";
+		reg = <0>;
+		spi-max-frequency = <5000000>;
+		spi-cpha;
+		spi-cpol;
+		pagesize = <32>;
+		size = <2048>;
+		address-width = <16>;
+	};
+};
+
+&i2c2 {
+	clock-frequency = <400000>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_i2c2>;
+	status = "okay";
+};
+
+&i2c4 {
+	clock-frequency = <400000>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_i2c4>;
+	status = "okay";
+
+	wm8962: audio-codec@1a {
+		compatible = "wlf,wm8962";
+		reg = <0x1a>;
+		clocks = <&clk IMX8MM_CLK_SAI3_ROOT>;
+		clock-names = "xclk";
+		DCVDD-supply = <&reg_audio>;
+		DBVDD-supply = <&reg_audio>;
+		AVDD-supply = <&reg_audio>;
+		CPVDD-supply = <&reg_audio>;
+		MICVDD-supply = <&reg_audio>;
+		PLLVDD-supply = <&reg_audio>;
+		SPKVDD1-supply = <&reg_audio>;
+		SPKVDD2-supply = <&reg_audio>;
+		gpio-cfg = <
+			0x0000 /* 0:Default */
+			0x0000 /* 1:Default */
+			0x0000 /* 2:FN_DMICCLK */
+			0x0000 /* 3:Default */
+			0x0000 /* 4:FN_DMICCDAT */
+			0x0000 /* 5:Default */
+		>;
+	};
+
+	pca6416_0: gpio@20 {
+		compatible = "nxp,pcal6416";
+		reg = <0x20>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_pcal6414>;
+		gpio-controller;
+		#gpio-cells = <2>;
+		interrupt-parent = <&gpio4>;
+		interrupts = <27 IRQ_TYPE_LEVEL_LOW>;
+	};
+
+	pca6416_1: gpio@21 {
+		compatible = "nxp,pcal6416";
+		reg = <0x21>;
+		gpio-controller;
+		#gpio-cells = <2>;
+		interrupt-parent = <&gpio4>;
+		interrupts = <27 IRQ_TYPE_LEVEL_LOW>;
+	};
+};
+
+&sai3 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_sai3>;
+	assigned-clocks = <&clk IMX8MM_CLK_SAI3>;
+	assigned-clock-parents = <&clk IMX8MM_AUDIO_PLL1_OUT>;
+	assigned-clock-rates = <24576000>;
+	fsl,sai-mclk-direction-output;
+	status = "okay";
+};
+
+&snvs_pwrkey {
+	status = "okay";
+};
+
+&uart2 { /* console */
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_uart2>;
+	status = "okay";
+};
+
+&uart3 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_uart3>;
+	assigned-clocks = <&clk IMX8MM_CLK_UART3>;
+	assigned-clock-parents = <&clk IMX8MM_SYS_PLL1_80M>;
+	status = "okay";
+};
+
+&usdhc2 {
+	pinctrl-names = "default", "state_100mhz", "state_200mhz";
+	pinctrl-0 = <&pinctrl_usdhc2>, <&pinctrl_usdhc2_gpio>;
+	pinctrl-1 = <&pinctrl_usdhc2_100mhz>;
+	pinctrl-2 = <&pinctrl_usdhc2_200mhz>;
+	bus-width = <4>;
+	vmmc-supply = <&reg_usdhc2_vmmc>;
+	status = "okay";
+};
+
+&iomuxc {
+	pinctrl_espi2: espi2grp {
+		fsl,pins = <
+			MX8MM_IOMUXC_ECSPI2_SCLK_ECSPI2_SCLK		0x82
+			MX8MM_IOMUXC_ECSPI2_MOSI_ECSPI2_MOSI		0x82
+			MX8MM_IOMUXC_ECSPI2_MISO_ECSPI2_MISO		0x82
+			MX8MM_IOMUXC_ECSPI1_SS0_GPIO5_IO9		0x41
+		>;
+	};
+
+	pinctrl_i2c2: i2c2grp {
+		fsl,pins = <
+			MX8MM_IOMUXC_I2C2_SCL_I2C2_SCL		0x400001c3
+			MX8MM_IOMUXC_I2C2_SDA_I2C2_SDA		0x400001c3
+		>;
+	};
+
+	pinctrl_i2c4: i2c4grp {
+		fsl,pins = <
+			MX8MM_IOMUXC_I2C4_SCL_I2C4_SCL		0x400001c3
+			MX8MM_IOMUXC_I2C4_SDA_I2C4_SDA		0x400001c3
+		>;
+	};
+
+	pinctrl_led3: led3grp {
+		fsl,pins = <
+			MX8MM_IOMUXC_SAI3_RXFS_GPIO4_IO28	0x41
+		>;
+	};
+
+	pinctrl_pcal6414: pcal6414-gpio {
+		fsl,pins = <
+			MX8MM_IOMUXC_SAI2_MCLK_GPIO4_IO27		0x19
+		>;
+	};
+
+	pinctrl_sai3: sai3grp {
+		fsl,pins = <
+			MX8MM_IOMUXC_SAI3_TXFS_SAI3_TX_SYNC     0xd6
+			MX8MM_IOMUXC_SAI3_TXC_SAI3_TX_BCLK      0xd6
+			MX8MM_IOMUXC_SAI3_MCLK_SAI3_MCLK        0xd6
+			MX8MM_IOMUXC_SAI3_TXD_SAI3_TX_DATA0     0xd6
+			MX8MM_IOMUXC_SAI3_RXD_SAI3_RX_DATA0	0xd6
+		>;
+	};
+
+	pinctrl_uart2: uart2grp {
+		fsl,pins = <
+			MX8MM_IOMUXC_UART2_RXD_UART2_DCE_RX	0x140
+			MX8MM_IOMUXC_UART2_TXD_UART2_DCE_TX	0x140
+		>;
+	};
+
+	pinctrl_uart3: uart3grp {
+		fsl,pins = <
+			MX8MM_IOMUXC_ECSPI1_SCLK_UART3_DCE_RX	0x40
+			MX8MM_IOMUXC_ECSPI1_MOSI_UART3_DCE_TX	0x40
+		>;
+	};
+
+	pinctrl_usdhc2_gpio: usdhc2grpgpio {
+		fsl,pins = <
+			MX8MM_IOMUXC_SD2_CD_B_USDHC2_CD_B	0x41
+			MX8MM_IOMUXC_SD2_RESET_B_GPIO2_IO19	0x41
+		>;
+	};
+
+	pinctrl_usdhc2: usdhc2grp {
+		fsl,pins = <
+			MX8MM_IOMUXC_SD2_CLK_USDHC2_CLK	0x190
+			MX8MM_IOMUXC_SD2_CMD_USDHC2_CMD	0x1d0
+			MX8MM_IOMUXC_SD2_DATA0_USDHC2_DATA0	0x1d0
+			MX8MM_IOMUXC_SD2_DATA1_USDHC2_DATA1	0x1d0
+			MX8MM_IOMUXC_SD2_DATA2_USDHC2_DATA2	0x1d0
+			MX8MM_IOMUXC_SD2_DATA3_USDHC2_DATA3	0x1d0
+			MX8MM_IOMUXC_GPIO1_IO04_USDHC2_VSELECT	0x1d0
+		>;
+	};
+
+	pinctrl_usdhc2_100mhz: usdhc2grp100mhz {
+		fsl,pins = <
+			MX8MM_IOMUXC_SD2_CLK_USDHC2_CLK	0x194
+			MX8MM_IOMUXC_SD2_CMD_USDHC2_CMD	0x1d4
+			MX8MM_IOMUXC_SD2_DATA0_USDHC2_DATA0	0x1d4
+			MX8MM_IOMUXC_SD2_DATA1_USDHC2_DATA1	0x1d4
+			MX8MM_IOMUXC_SD2_DATA2_USDHC2_DATA2	0x1d4
+			MX8MM_IOMUXC_SD2_DATA3_USDHC2_DATA3	0x1d4
+			MX8MM_IOMUXC_GPIO1_IO04_USDHC2_VSELECT	0x1d0
+		>;
+	};
+
+	pinctrl_usdhc2_200mhz: usdhc2grp200mhz {
+		fsl,pins = <
+			MX8MM_IOMUXC_SD2_CLK_USDHC2_CLK	0x196
+			MX8MM_IOMUXC_SD2_CMD_USDHC2_CMD	0x1d6
+			MX8MM_IOMUXC_SD2_DATA0_USDHC2_DATA0	0x1d6
+			MX8MM_IOMUXC_SD2_DATA1_USDHC2_DATA1	0x1d6
+			MX8MM_IOMUXC_SD2_DATA2_USDHC2_DATA2	0x1d6
+			MX8MM_IOMUXC_SD2_DATA3_USDHC2_DATA3	0x1d6
+			MX8MM_IOMUXC_GPIO1_IO04_USDHC2_VSELECT	0x1d0
+		>;
+	};
+};
arch/arm64/boot/dts/freescale/imx8mm-beacon-kit.dts new file +19 -0
new file mode 100644
index 000000000000..74a7b0cc10c2
@@ -0,0 +1,19 @@
+// SPDX-License-Identifier: (GPL-2.0 OR MIT)
+/*
+ * Copyright 2020 Compass Electronics Group, LLC
+ */
+
+/dts-v1/;
+
+#include "imx8mm.dtsi"
+#include "imx8mm-beacon-som.dtsi"
+#include "imx8mm-beacon-baseboard.dtsi"
+
+/ {
+	model = "Beacon EmbeddedWorks i.MX8M Mini Development Kit";
+	compatible = "beacon,imx8mm-beacon-kit", "fsl,imx8mm";
+
+	chosen {
+		stdout-path = &uart2;
+	};
+};
arch/arm64/boot/dts/freescale/imx8mm-beacon-som.dtsi new file +410 -0

410 lines not on this page · raw message

Signature · 1 line
2.25.1
reviewer Reviewed-by on v1 2/2
#2 lore raw

Re: [PATCH 2/2] arm64: dts: imx: Add Beacon i.MX8m-Mini development kit

Quoted 7 lines · Adam Ford

Beacon Embeddedworks is launching a development kit based on the i.MX8M Mini SoC. The kit consists of a System on Module (SOM)
+ baseboard. The SOM has the SoC, eMMC, and Ethernet. The baseboard has an wm8962 audio CODEC, a single USB OTG, and three USB host ports.

author
#3 lore raw

Re: [PATCH 2/2] arm64: dts: imx: Add Beacon i.MX8m-Mini development kit

Quoted 11 lines · Fabio Estevam
Quoted 7 lines · Adam Ford

Beacon Embeddedworks is launching a development kit based on the i.MX8M Mini SoC. The kit consists of a System on Module (SOM)
+ baseboard. The SOM has the SoC, eMMC, and Ethernet. The baseboard has an wm8962 audio CODEC, a single USB OTG, and three USB host ports.

Shawn,

Is there any possibility to get applied to imx-next before RC1 is cut?

adam

Applied
#4 lore raw

Re: [PATCH 2/2] arm64: dts: imx: Add Beacon i.MX8m-Mini development kit

In reply to Adam Ford
Quoted 6 lines · Adam Ford

Beacon Embeddedworks is launching a development kit based on the i.MX8M Mini SoC. The kit consists of a System on Module (SOM)
+ baseboard. The SOM has the SoC, eMMC, and Ethernet. The baseboard has an wm8962 audio CODEC, a single USB OTG, and three USB host ports.

Applied, thanks.

#6 lore raw
In reply to Adam Ford
Quoted 5 lines · Adam Ford

Beacon EmebeddedWorks is the brand owned by Compass Electronics Group, LLC based out of the United States.
https://beaconembedded.com/

Hi Rob,

Are you okay with this?

Shawn

Quoted 17 lines
Documentation/devicetree/bindings/vendor-prefixes.yaml +2 -0
index 4c8eaa11daff..7ee772b1840a 100644
@@ -141,6 +141,8 @@ patternProperties:
     description: Shenzhen AZW Technology Co., Ltd.
   "^bananapi,.*":
     description: BIPAI KEJI LIMITED
+  "^beacon,.*":
+    description: Compass Electronics Group, LLC
   "^bhf,.*":
     description: Beckhoff Automation GmbH & Co. KG
   "^bitmain,.*":
Signature · 1 line
2.25.1