ARM: tegra: Add NVIDIA Jetson Nano Developer Kit support
Subsystems (3)
PATCH 1/1 ARM: tegra: Add NVIDIA Jetson Nano Developer Kit support
From: Tom Warren <[email protected]>
The Jetson Nano Developer Kit is a Tegra X1-based development board. It is similar to Jetson TX1 but it is not pin compatible. It features 4GB of LPDDR4, a SPI NOR flash for early boot firmware and an SD card slot used for storage.
HDMI 2.0 or DP 1.2 are available for display, four USB ports (3 USB 2.0 and 1 USB 3.0) can be used to attach a variety of peripherals and a PCI Ethernet controller provides onboard network connectivity. NVMe support has also been added. Env save is at the end of QSPI (4MB-8K).
A 40-pin header on the board can be used to extend the capabilities and exposed interfaces of the Jetson Nano.
--- arch/arm/dts/Makefile | 3 +- arch/arm/dts/tegra210-p3450-0000.dts | 147 +++++++++++++++++++++++++++++ arch/arm/mach-tegra/board2.c | 25 +++++ arch/arm/mach-tegra/tegra210/Kconfig | 7 ++ board/nvidia/p3450-0000/Kconfig | 12 +++ board/nvidia/p3450-0000/MAINTAINERS | 6 ++ board/nvidia/p3450-0000/Makefile | 8 ++ board/nvidia/p3450-0000/p3450-0000.c | 178 +++++++++++++++++++++++++++++++++++ configs/p3450-0000_defconfig | 64 +++++++++++++ include/configs/p3450-0000.h | 46 +++++++++ 10 files changed, 495 insertions(+), 1 deletion(-) create mode 100644 arch/arm/dts/tegra210-p3450-0000.dts create mode 100644 board/nvidia/p3450-0000/Kconfig create mode 100644 board/nvidia/p3450-0000/MAINTAINERS create mode 100644 board/nvidia/p3450-0000/Makefile create mode 100644 board/nvidia/p3450-0000/p3450-0000.c create mode 100644 configs/p3450-0000_defconfig create mode 100644 include/configs/p3450-0000.h
arch/arm/dts/Makefile +2 -1
@@ -180,7 +180,8 @@ dtb-$(CONFIG_TEGRA) += tegra20-harmony.dtb \ tegra210-e2220-1170.dtb \ tegra210-p2371-0000.dtb \ tegra210-p2371-2180.dtb \ - tegra210-p2571.dtb + tegra210-p2571.dtb \ + tegra210-p3450-0000.dtb dtb-$(CONFIG_ARCH_MVEBU) += \ armada-3720-db.dtb \
arch/arm/dts/tegra210-p3450-0000.dts new file +147 -0
147 lines not on this page · raw message
arch/arm/mach-tegra/board2.c +25 -0
@@ -217,6 +217,31 @@ int board_early_init_f(void)arch_timer_init ();#endif +#if defined(CONFIG_DISABLE_SDMMC1_EARLY ) +/* +* Turn off (reset/disable) SDMMC1 on Nano here, before GPIO INIT. +* We do this because earlier bootloaders have enabled power to +* SDMMC1 on Nano, and toggling power-gpio (PZ3) in pinmux_init() +* results in power being back-driven into the SD-card and SDMMC1 +* HW, which is 'bad' as per the HW team. +* +* From the HW team: "LDO2 from the PMIC has already been set to 3.3v in +* nvtboot/CBoot on Nano (for SD-card boot). So when U-Boot's GPIO_INIT +* table sets PZ3 to OUT0 as per the pinmux spreadsheet, it turns off +* the loadswitch. When PZ3 is 0 and not driving, essentially the SDCard +* voltage turns off. Since the SDCard voltage is no longer there, the +* SDMMC CLK/DAT lines are backdriving into what essentially is a +* powered-off SDCard, that's why the voltage drops from 3.3V to ~1.6V" +* +* Note that this can probably be removed when we change over to storing +* all BL components on QSPI on Nano, and U-Boot then becomes the first +* one to turn on SDMMC1 power. Another fix would be to have CBoot +* disable power/gate SDMMC1 off before handing off to U-Boot/kernel. +*/ +reset_set_enable (PERIPH_ID_SDMMC1 ,1 ); +clock_set_enable (PERIPH_ID_SDMMC1 ,0 ); +#endif /* CONFIG_DISABLE_SDMMC1_EARLY */ +pinmux_init ();board_init_uart_f ();
arch/arm/mach-tegra/tegra210/Kconfig +7 -0
@@ -35,6 +35,12 @@ config TARGET_P2571 help P2571 is a P2530 married to a P1963 I/O board +config TARGET_P3450_0000 + bool "NVIDIA Jetson Nano Developer Kit" + select BOARD_LATE_INIT + help + P3450-0000 is a P3448 CPU board married to a P3449 I/O board. + endchoice config SYS_SOC
@@ -44,5 +50,6 @@ source "board/nvidia/e2220-1170/Kconfig" source "board/nvidia/p2371-0000/Kconfig" source "board/nvidia/p2371-2180/Kconfig" source "board/nvidia/p2571/Kconfig" +source "board/nvidia/p3450-0000/Kconfig" endif
board/nvidia/p3450-0000/Kconfig new file +12 -0
@@ -0,0 +1,12 @@ +if TARGET_P3450_0000 + +config SYS_BOARD + default "p3450-0000" + +config SYS_VENDOR + default "nvidia" + +config SYS_CONFIG_NAME + default "p3450-0000" + +endif
board/nvidia/p3450-0000/MAINTAINERS new file +6 -0
@@ -0,0 +1,6 @@ +P3450-0000 BOARD +M: Tom Warren <[email protected]> +S: Maintained +F: board/nvidia/p3450-0000/ +F: include/configs/p3450-0000.h +F: configs/p3450-0000_defconfig
board/nvidia/p3450-0000/Makefile new file +8 -0
@@ -0,0 +1,8 @@ +# +# (C) Copyright 2018 +# NVIDIA Corporation <www.nvidia.com> +# +# SPDX-License-Identifier: GPL-2.0+ +# + +obj-y += p3450-0000.o
board/nvidia/p3450-0000/p3450-0000.c new file +178 -0
178 lines not on this page · raw message
configs/p3450-0000_defconfig new file +64 -0
64 lines not on this page · raw message
include/configs/p3450-0000.h new file +46 -0
46 lines not on this page · raw message
Signature · 9 lines
1.8.2.1.610.g562af5b ----------------------------------------------------------------------------------- This email message is for the sole use of the intended recipient(s) and may contain confidential information. Any unauthorized review, use, disclosure or distribution is prohibited. If you are not the intended recipient, please contact the sender by reply email and destroy all copies of the original message. -----------------------------------------------------------------------------------
PATCH 1/1 ARM: tegra: Add NVIDIA Jetson Nano Developer Kit support
Hi Tom,
Do you have this and the other patches you've posted on a git branch somewhere, for some reason they're not showing up in patchwork [1] which makes it less straight forward to test.
Peter
[1] http://patchwork.ozlabs.org/project/uboot/list/?q=tegra
Quoted 625 lines · On Tue, Mar 24, 2020 at 7:03 PM <[email protected]> wrote:
From: Tom Warren <[email protected]>
The Jetson Nano Developer Kit is a Tegra X1-based development board. It is similar to Jetson TX1 but it is not pin compatible. It features 4GB of LPDDR4, a SPI NOR flash for early boot firmware and an SD card slot used for storage.
HDMI 2.0 or DP 1.2 are available for display, four USB ports (3 USB 2.0 and 1 USB 3.0) can be used to attach a variety of peripherals and a PCI Ethernet controller provides onboard network connectivity. NVMe support has also been added. Env save is at the end of QSPI (4MB-8K).
A 40-pin header on the board can be used to extend the capabilities and exposed interfaces of the Jetson Nano.
Signed-off-by Thierry Reding <[email protected]>Signed-off-by Tom Warren <[email protected]>--- arch/arm/dts/Makefile | 3 +- arch/arm/dts/tegra210-p3450-0000.dts | 147 +++++++++++++++++++++++++++++ arch/arm/mach-tegra/board2.c | 25 +++++ arch/arm/mach-tegra/tegra210/Kconfig | 7 ++ board/nvidia/p3450-0000/Kconfig | 12 +++ board/nvidia/p3450-0000/MAINTAINERS | 6 ++ board/nvidia/p3450-0000/Makefile | 8 ++ board/nvidia/p3450-0000/p3450-0000.c | 178 +++++++++++++++++++++++++++++++++++ configs/p3450-0000_defconfig | 64 +++++++++++++ include/configs/p3450-0000.h | 46 +++++++++ 10 files changed, 495 insertions(+), 1 deletion(-) create mode 100644 arch/arm/dts/tegra210-p3450-0000.dts create mode 100644 board/nvidia/p3450-0000/Kconfig create mode 100644 board/nvidia/p3450-0000/MAINTAINERS create mode 100644 board/nvidia/p3450-0000/Makefile create mode 100644 board/nvidia/p3450-0000/p3450-0000.c create mode 100644 configs/p3450-0000_defconfig create mode 100644 include/configs/p3450-0000.harch/arm/dts/Makefile +2
-1@@ -180,7 +180,8 @@ dtb-$(CONFIG_TEGRA) += tegra20-harmony.dtb \ tegra210-e2220-1170.dtb \ tegra210-p2371-0000.dtb \ tegra210-p2371-2180.dtb \ - tegra210-p2571.dtb + tegra210-p2571.dtb \ + tegra210-p3450-0000.dtb dtb-$(CONFIG_ARCH_MVEBU) += \ armada-3720-db.dtb \arch/arm/dts/tegra210-p3450-0000.dts new file +147
-0@@ -0,0 +1,147 @@ +// SPDX-License-Identifier: GPL-2.0+ +/* + * (C) Copyright 2019-2020 NVIDIA Corporation <www.nvidia.com> + */ +/dts-v1/; + +#include "tegra210.dtsi" + +/ { + model = "NVIDIA Jetson Nano Developer Kit"; + compatible = "nvidia,p3450-0000", "nvidia,tegra210"; + + chosen { + stdout-path = &uarta; + }; + + aliases { + ethernet = "/pcie at 1003000/pci at 2,0/ethernet at 0,0"; + i2c0 = "/i2c at 7000d000"; + i2c2 = "/i2c at 7000c400"; + i2c3 = "/i2c at 7000c500"; + i2c4 = "/i2c at 7000c700"; + mmc0 = "/sdhci at 700b0600"; + mmc1 = "/sdhci at 700b0000"; + spi0 = "/spi at 70410000"; + usb0 = "/usb at 7d000000"; + }; + + memory { + reg = <0x0 0x80000000 0x0 0xc0000000>; + }; + + pcie at 1003000 { + status = "okay"; + + pci at 1,0 { + status = "okay"; + }; + + pci at 2,0 { + status = "okay"; + + ethernet at 0,0 { + reg = <0x000000 0 0 0 0>; + local-mac-address = [ 00 00 00 00 00 00 ]; + }; + }; + }; + + serial at 70006000 { + status = "okay"; + }; + + padctl at 7009f000 { + pinctrl-0 = <&padctl_default>; + pinctrl-names = "default"; + + padctl_default: pinmux { + xusb { + nvidia,lanes = "otg-1", "otg-2"; + nvidia,function = "xusb"; + nvidia,iddq = <0>; + }; + + usb3 { + nvidia,lanes = "pcie-5", "pcie-6"; + nvidia,function = "usb3"; + nvidia,iddq = <0>; + }; + + pcie-x1 { + nvidia,lanes = "pcie-0"; + nvidia,function = "pcie-x1"; + nvidia,iddq = <0>; + }; + + pcie-x4 { + nvidia,lanes = "pcie-1", "pcie-2", + "pcie-3", "pcie-4"; + nvidia,function = "pcie-x4"; + nvidia,iddq = <0>; + }; + + sata { + nvidia,lanes = "sata-0"; + nvidia,function = "sata"; + nvidia,iddq = <0>; + }; + }; + }; + + sdhci at 700b0000 { + status = "okay"; + cd-gpios = <&gpio TEGRA_GPIO(Z, 1) GPIO_ACTIVE_LOW>; + power-gpios = <&gpio TEGRA_GPIO(Z, 3) GPIO_ACTIVE_HIGH>; + bus-width = <4>; + }; + + sdhci at 700b0600 { + status = "okay"; + bus-width = <8>; + non-removable; + }; + + i2c at 7000c400 { + status = "okay"; + clock-frequency = <400000>; + }; + + i2c at 7000c500 { + status = "okay"; + clock-frequency = <400000>; + }; + + i2c at 7000c700 { + status = "okay"; + clock-frequency = <400000>; + }; + + i2c at 7000d000 { + status = "okay"; + clock-frequency = <400000>; + }; + + spi at 70410000 { + status = "okay"; + spi-max-frequency = <80000000>; + }; + + usb at 7d000000 { + status = "okay"; + dr_mode = "peripheral"; + }; + + clocks { + compatible = "simple-bus"; + #address-cells = <1>; + #size-cells = <0>; + + clk32k_in: clock at 0 { + compatible = "fixed-clock"; + reg = <0>; + #clock-cells = <0>; + clock-frequency = <32768>; + }; + }; +};arch/arm/mach-tegra/board2.c +25
-0@@ -217,6 +217,31 @@ int board_early_init_f(void)arch_timer_init ();#endif +#if defined(CONFIG_DISABLE_SDMMC1_EARLY ) +/* +* Turn off (reset/disable) SDMMC1 on Nano here, before GPIO INIT. +* We do this because earlier bootloaders have enabled power to +* SDMMC1 on Nano, and toggling power-gpio (PZ3) in pinmux_init() +* results in power being back-driven into the SD-card and SDMMC1 +* HW, which is 'bad' as per the HW team. +* +* From the HW team: "LDO2 from the PMIC has already been set to 3.3v in +* nvtboot/CBoot on Nano (for SD-card boot). So when U-Boot's GPIO_INIT +* table sets PZ3 to OUT0 as per the pinmux spreadsheet, it turns off +* the loadswitch. When PZ3 is 0 and not driving, essentially the SDCard +* voltage turns off. Since the SDCard voltage is no longer there, the +* SDMMC CLK/DAT lines are backdriving into what essentially is a +* powered-off SDCard, that's why the voltage drops from 3.3V to ~1.6V" +* +* Note that this can probably be removed when we change over to storing +* all BL components on QSPI on Nano, and U-Boot then becomes the first +* one to turn on SDMMC1 power. Another fix would be to have CBoot +* disable power/gate SDMMC1 off before handing off to U-Boot/kernel. +*/ +reset_set_enable (PERIPH_ID_SDMMC1 ,1 ); +clock_set_enable (PERIPH_ID_SDMMC1 ,0 ); +#endif /* CONFIG_DISABLE_SDMMC1_EARLY */ +pinmux_init ();board_init_uart_f ();arch/arm/mach-tegra/tegra210/Kconfig +7
-0@@ -35,6 +35,12 @@ config TARGET_P2571 help P2571 is a P2530 married to a P1963 I/O board +config TARGET_P3450_0000 + bool "NVIDIA Jetson Nano Developer Kit" + select BOARD_LATE_INIT + help + P3450-0000 is a P3448 CPU board married to a P3449 I/O board. + endchoice config SYS_SOC@@ -44,5 +50,6 @@ source "board/nvidia/e2220-1170/Kconfig" source "board/nvidia/p2371-0000/Kconfig" source "board/nvidia/p2371-2180/Kconfig" source "board/nvidia/p2571/Kconfig" +source "board/nvidia/p3450-0000/Kconfig" endifboard/nvidia/p3450-0000/Kconfig new file +12
-0@@ -0,0 +1,12 @@ +if TARGET_P3450_0000 + +config SYS_BOARD + default "p3450-0000" + +config SYS_VENDOR + default "nvidia" + +config SYS_CONFIG_NAME + default "p3450-0000" + +endifboard/nvidia/p3450-0000/MAINTAINERS new file +6
-0@@ -0,0 +1,6 @@ +P3450-0000 BOARD +M: Tom Warren <[email protected]> +S: Maintained +F: board/nvidia/p3450-0000/ +F: include/configs/p3450-0000.h +F: configs/p3450-0000_defconfigboard/nvidia/p3450-0000/Makefile new file +8
-0@@ -0,0 +1,8 @@ +# +# (C) Copyright 2018 +# NVIDIA Corporation <www.nvidia.com> +# +# SPDX-License-Identifier: GPL-2.0+ +# + +obj-y += p3450-0000.oboard/nvidia/p3450-0000/p3450-0000.c new file +178
-0@@ -0,0 +1,178 @@ +// SPDX-License-Identifier: GPL-2.0+ +/* +* (C) Copyright 2018-2019 +* NVIDIA Corporation <www.nvidia.com> +* +*/ + +#include <common.h> +#include <fdtdec.h> +#include <i2c.h> +#include <linux/libfdt.h> +#include <pca953x.h> +#include <asm/arch-tegra/cboot.h> +#include <asm/arch/gpio.h> +#include <asm/arch/pinmux.h> +#include "../p2571/max77620_init.h" + +void pin_mux_mmc (void ) +{ +struct udevice *dev; +uchar val; +int ret; + +/* Turn on MAX77620 LDO2 to 3.3V for SD card power */ +debug ("%s: Set LDO2 for VDDIO_SDMMC_AP power to 3.3V\n" , __func__); + ret =i2c_get_chip_for_busnum (0 ,MAX77620_I2C_ADDR_7BIT ,1 , &dev); +if (ret) { +printf ("%s: Cannot find MAX77620 I2C chip\n" , __func__); +return ; + } +/* 0xF2 for 3.3v, enabled: bit7:6 = 11 = enable, bit5:0 = voltage */ + val =0xF2 ; + ret =dm_i2c_write (dev,MAX77620_CNFG1_L2_REG , &val,1 ); +if (ret) +printf ("i2c_write 0 0x3c 0x27 failed: %d\n" , ret); + +/* Disable LDO4 discharge */ + ret =dm_i2c_read (dev,MAX77620_CNFG2_L4_REG , &val,1 ); +if (ret) { +printf ("i2c_read 0 0x3c 0x2c failed: %d\n" , ret); + }else { + val &= ~BIT (1 );/* ADE */ + ret =dm_i2c_write (dev,MAX77620_CNFG2_L4_REG , &val,1 ); +if (ret) +printf ("i2c_write 0 0x3c 0x2c failed: %d\n" , ret); + } + +/* Set MBLPD */ + ret =dm_i2c_read (dev,MAX77620_CNFGGLBL1_REG , &val,1 ); +if (ret) { +printf ("i2c_write 0 0x3c 0x00 failed: %d\n" , ret); + }else { + val |=BIT (6 );/* MBLPD */ + ret =dm_i2c_write (dev,MAX77620_CNFGGLBL1_REG , &val,1 ); +if (ret) +printf ("i2c_write 0 0x3c 0x00 failed: %d\n" , ret); + } +} + +#ifdef CONFIG_PCI_TEGRA +int tegra_pcie_board_init (void ) +{ +struct udevice *dev; +uchar val; +int ret; + +/* Turn on MAX77620 LDO1 to 1.05V for PEX power */ +debug ("%s: Set LDO1 for PEX power to 1.05V\n" , __func__); + ret =i2c_get_chip_for_busnum (0 ,MAX77620_I2C_ADDR_7BIT ,1 , &dev); +if (ret) { +printf ("%s: Cannot find MAX77620 I2C chip\n" , __func__); +return -1 ; + } +/* 0xCA for 1.05v, enabled: bit7:6 = 11 = enable, bit5:0 = voltage */ + val =0xCA ; + ret =dm_i2c_write (dev,MAX77620_CNFG1_L1_REG , &val,1 ); +if (ret) +printf ("i2c_write 0 0x3c 0x25 failed: %d\n" , ret); + +return 0 ; +} +#endif /* PCI */ + +static void ft_mac_address_setup (void *fdt) +{ +const void *cboot_fdt = (const void *)cboot_boot_x0; +uint8_t mac[ETH_ALEN ], local_mac[ETH_ALEN ]; +const char *path; +int offset, err; + + err =cboot_get_ethaddr (cboot_fdt, local_mac); +if (err <0 ) +memset (local_mac,0 ,ETH_ALEN ); + + path =fdt_get_alias (fdt,"ethernet" ); +if (!path) +return ; + +debug ("ethernet alias found: %s\n" , path); + + offset =fdt_path_offset (fdt, path); +if (offset <0 ) { +printf ("ethernet alias points to absent node %s\n" , path); +return ; + } + +if (is_valid_ethaddr (local_mac)) { + err =fdt_setprop (fdt, offset,"local-mac-address" , local_mac, +ETH_ALEN ); +if (!err) +debug ("Local MAC address set: %pM\n" , local_mac); + } + +if (eth_env_get_enetaddr ("ethaddr" , mac)) { +if (memcmp (local_mac, mac,ETH_ALEN ) !=0 ) { + err =fdt_setprop (fdt, offset,"mac-address" , mac, +ETH_ALEN ); +if (!err) +debug ("MAC address set: %pM\n" , mac); + } + } +} + +static int ft_copy_carveout (void *dst,const void *src,const char *node) +{ +struct fdt_memory fb; +int err; + + err =fdtdec_get_carveout (src, node,"memory-region" ,0 , &fb); +if (err <0 ) { +if (err != -FDT_ERR_NOTFOUND ) +printf ("failed to get carveout for %s: %d\n" , node, + err); + +return err; + } + + err =fdtdec_set_carveout (dst, node,"memory-region" ,0 ,"framebuffer" , + &fb); +if (err <0 ) { +printf ("failed to set carveout for %s: %d\n" , node, err); +return err; + } + +return 0 ; +} + +static void ft_carveout_setup (void *fdt) +{ +const void *cboot_fdt = (const void *)cboot_boot_x0; +static const char *const nodes[] = { +"/host1x at 50000000/dc at 54200000" , +"/host1x at 50000000/dc at 54240000" , + }; +unsigned int i; +int err; + +for (i =0 ; i <ARRAY_SIZE (nodes); i++) { +printf ("copying carveout for %s...\n" , nodes[i]); + + err =ft_copy_carveout (fdt, cboot_fdt, nodes[i]); +if (err <0 ) { +if (err != -FDT_ERR_NOTFOUND ) +printf ("failed to copy carveout for %s: %d\n" , + nodes[i], err); + +continue ; + } + } +} + +int ft_board_setup (void *fdt,bd_t *bd) +{ +ft_mac_address_setup (fdt); +ft_carveout_setup (fdt); + +return 0 ; +}configs/p3450-0000_defconfig new file +64
-0@@ -0,0 +1,64 @@ +CONFIG_ARM=y +CONFIG_TEGRA=y +CONFIG_SYS_TEXT_BASE=0x80080000 +CONFIG_TEGRA210=y +CONFIG_TARGET_P3450_0000=y +CONFIG_NR_DRAM_BANKS=2 +CONFIG_OF_SYSTEM_SETUP=y +CONFIG_OF_BOARD_SETUP=y +CONFIG_CONSOLE_MUX=y +CONFIG_SYS_STDIO_DEREGISTER=y +CONFIG_SYS_PROMPT="Tegra210 (P3450-0000) # " +# CONFIG_CMD_IMI is not set +CONFIG_CMD_DFU=y +# CONFIG_CMD_FLASH is not set +CONFIG_CMD_GPIO=y +CONFIG_CMD_I2C=y +CONFIG_CMD_MMC=y +CONFIG_CMD_PCI=y +CONFIG_CMD_SF=y +CONFIG_CMD_SPI=y +CONFIG_CMD_USB=y +CONFIG_CMD_USB_MASS_STORAGE=y +# CONFIG_CMD_SETEXPR is not set +# CONFIG_CMD_NFS is not set +CONFIG_CMD_EXT4_WRITE=y +CONFIG_OF_LIVE=y +CONFIG_DEFAULT_DEVICE_TREE="tegra210-p3450-0000" +CONFIG_DFU_MMC=y +CONFIG_DFU_RAM=y +CONFIG_DFU_SF=y +CONFIG_SYS_I2C_TEGRA=y +CONFIG_SPI_FLASH=y +CONFIG_SPI_FLASH_MACRONIX=y +CONFIG_SPI_FLASH_USE_4K_SECTORS=y +CONFIG_SF_DEFAULT_MODE=0 +CONFIG_SF_DEFAULT_SPEED=24000000 +CONFIG_RTL8169=y +CONFIG_PCI=y +CONFIG_DM_PCI=y +CONFIG_DM_PCI_COMPAT=y +CONFIG_PCI_TEGRA=y +CONFIG_SYS_NS16550=y +CONFIG_TEGRA114_SPI=y +CONFIG_TEGRA210_QSPI=y +CONFIG_USB=y +CONFIG_DM_USB=y +CONFIG_USB_EHCI_HCD=y +CONFIG_USB_EHCI_TEGRA=y +CONFIG_USB_GADGET=y +CONFIG_USB_GADGET_MANUFACTURER="NVIDIA" +CONFIG_USB_GADGET_VENDOR_NUM=0x0955 +CONFIG_USB_GADGET_PRODUCT_NUM=0x701a +CONFIG_CI_UDC=y +CONFIG_USB_GADGET_DOWNLOAD=y +CONFIG_USB_HOST_ETHER=y +CONFIG_USB_ETHER_ASIX=y +# CONFIG_ENV_IS_IN_MMC is not set +CONFIG_ENV_IS_IN_SPI_FLASH=y +CONFIG_ENV_SIZE=0x2000 +CONFIG_ENV_SECT_SIZE=0x1000 +CONFIG_ENV_OFFSET=0xFFFFE000 +CONFIG_BOOTP_PREFER_SERVERIP=y +CONFIG_DISABLE_SDMMC1_EARLY=y +CONFIG_NVME=yinclude/configs/p3450-0000.h new file +46
-1@@ -0,0 +1,46 @@ +/* SPDX-License-Identifier: GPL-2.0+ */ +/* +* (C) Copyright 2018-2019 NVIDIA Corporation. +*/ + +#ifndef _P3450_0000_H +#define _P3450_0000_H + +#include <linux/sizes.h> + +#include "tegra210-common.h" + +/* High-level configuration options */ +#define CONFIG_TEGRA_BOARD_STRING "NVIDIA P3450-0000" + +/* Board-specific serial config */ +#define CONFIG_TEGRA_ENABLE_UARTA + +/* Only MMC/PXE/DHCP for now, add USB back in later when supported */ +#define BOOT_TARGET_DEVICES (func) \ + func(MMC, mmc, 1) \ + func(MMC, mmc, 0) \ + func(PXE, pxe, na) \ + func(DHCP, dhcp, na) + +/* Environment at end of QSPI, in the VER partition */ +#define CONFIG_ENV_SPI_MAX_HZ 48000000 +#define CONFIG_ENV_SPI_MODE SPI_MODE_0 +#define CONFIG_SPI_FLASH_SIZE (4 << 20) + +#define CONFIG_PREBOOT + +#define BOARD_EXTRA_ENV_SETTINGS \ + "preboot=if test -e mmc 1:1 /u-boot-preboot.scr; then " \ + "load mmc 1:1 ${scriptaddr} /u-boot-preboot.scr; " \ + "source ${scriptaddr}; " \ + "fi\0" + +/* General networking support */ +#include "tegra-common-usb-gadget.h" +#include "tegra-common-post.h" + +/* Crystal is 38.4MHz. clk_m runs at half that rate */ +#define COUNTER_FREQUENCY 19200000 + +#endif /* _P3450_0000_H */ --1.8.2.1.610.g562af5b
-----------------------------------------------------------------------------------
This email message is for the sole use of the intended recipient(s) and may contain confidential information. Any unauthorized review, use, disclosure or distribution is prohibited. If you are not the intended recipient, please contact the sender by reply email and destroy all copies of the original message.
-----------------------------------------------------------------------------------
PATCH 1/1 ARM: tegra: Add NVIDIA Jetson Nano Developer Kit support
-----Original Message-----
From: Peter Robinson <[email protected]>
Sent: Wednesday, March 25, 2020 5:53 AM
To: Tom Warren <[email protected]>
Cc: u-boot at lists.denx.de; Stephen Warren <[email protected]>; Thierry Reding <[email protected]>; Jonathan Hunter <[email protected]>; tomcwarren3959 at gmail.com
Subject: Re: [PATCH] ARM: tegra: Add NVIDIA Jetson Nano Developer Kit support
External email: Use caution opening links or attachments
Hi Tom,
Do you have this and the other patches you've posted on a git branch somewhere, for some reason they're not showing up in patchwork [1] which makes it less straight forward to test.
Peter
[1] http://patchwork.ozlabs.org/project/uboot/list/?q=tegra
[Tom] That's weird, I sent them all using git send-email to u-boot at lists.denx.de. But you are right, I don't see any of them on Patchwork. TomR - any idea why? Peter - you can find all of the patches (plus a WIP fix for a couple of load address conflicts when loading an FDT from extlinux) in tegra/next upstream, just updated today.
Quoted 627 lines · On Tue, Mar 24, 2020 at 7:03 PM <[email protected]> wrote:
From: Tom Warren <[email protected]>
The Jetson Nano Developer Kit is a Tegra X1-based development board. It is similar to Jetson TX1 but it is not pin compatible. It features 4GB of LPDDR4, a SPI NOR flash for early boot firmware and an SD card slot used for storage.
HDMI 2.0 or DP 1.2 are available for display, four USB ports (3 USB 2.0 and 1 USB 3.0) can be used to attach a variety of peripherals and a PCI Ethernet controller provides onboard network connectivity. NVMe support has also been added. Env save is at the end of QSPI (4MB-8K).
A 40-pin header on the board can be used to extend the capabilities and exposed interfaces of the Jetson Nano.
Signed-off-by Thierry Reding <[email protected]>Signed-off-by Tom Warren <[email protected]>--- arch/arm/dts/Makefile | 3 +- arch/arm/dts/tegra210-p3450-0000.dts | 147 +++++++++++++++++++++++++++++ arch/arm/mach-tegra/board2.c | 25 +++++ arch/arm/mach-tegra/tegra210/Kconfig | 7 ++ board/nvidia/p3450-0000/Kconfig | 12 +++ board/nvidia/p3450-0000/MAINTAINERS | 6 ++ board/nvidia/p3450-0000/Makefile | 8 ++ board/nvidia/p3450-0000/p3450-0000.c | 178 +++++++++++++++++++++++++++++++++++ configs/p3450-0000_defconfig | 64 +++++++++++++ include/configs/p3450-0000.h | 46 +++++++++ 10 files changed, 495 insertions(+), 1 deletion(-) create mode 100644 arch/arm/dts/tegra210-p3450-0000.dts create mode 100644 board/nvidia/p3450-0000/Kconfig create mode 100644 board/nvidia/p3450-0000/MAINTAINERS create mode 100644 board/nvidia/p3450-0000/Makefile create mode 100644 board/nvidia/p3450-0000/p3450-0000.c create mode 100644 configs/p3450-0000_defconfig create mode 100644
include/configs/p3450-0000.harch/arm/dts/Makefile index renamed from arch/arm/dts/Makefile +0
-09c593b2..820ee97 100644
arch/arm/dts/Makefile +2
-1@@ -180,7 +180,8 @@ dtb-$(CONFIG_TEGRA) += tegra20-harmony.dtb \ tegra210-e2220-1170.dtb \ tegra210-p2371-0000.dtb \ tegra210-p2371-2180.dtb \ - tegra210-p2571.dtb + tegra210-p2571.dtb \ + tegra210-p3450-0000.dtb dtb-$(CONFIG_ARCH_MVEBU) += \ armada-3720-db.dtb \arch/arm/dts/tegra210-p3450-0000.dts new file +146
-0@@ -0,0 +1,147 @@ +// SPDX-License-Identifier: GPL-2.0+ +/* + * (C) Copyright 2019-2020 NVIDIA Corporation <www.nvidia.com> */ +/dts-v1/; + +#include "tegra210.dtsi" + +/ { + model = "NVIDIA Jetson Nano Developer Kit"; + compatible = "nvidia,p3450-0000", "nvidia,tegra210"; + + chosen { + stdout-path = &uarta; + }; + + aliases { + ethernet = "/pcie at 1003000/pci at 2,0/ethernet at 0,0"; + i2c0 = "/i2c at 7000d000"; + i2c2 = "/i2c at 7000c400"; + i2c3 = "/i2c at 7000c500"; + i2c4 = "/i2c at 7000c700"; + mmc0 = "/sdhci at 700b0600"; + mmc1 = "/sdhci at 700b0000"; + spi0 = "/spi at 70410000"; + usb0 = "/usb at 7d000000"; + }; + + memory { + reg = <0x0 0x80000000 0x0 0xc0000000>; + }; + + pcie at 1003000 { + status = "okay"; + + pci at 1,0 { + status = "okay"; + }; + + pci at 2,0 { + status = "okay"; + + ethernet at 0,0 { + reg = <0x000000 0 0 0 0>; + local-mac-address = [ 00 00 00 00 00 00 ]; + }; + }; + }; + + serial at 70006000 { + status = "okay"; + }; + + padctl at 7009f000 { + pinctrl-0 = <&padctl_default>; + pinctrl-names = "default"; + + padctl_default: pinmux { + xusb { + nvidia,lanes = "otg-1", "otg-2"; + nvidia,function = "xusb"; + nvidia,iddq = <0>; + }; + + usb3 { + nvidia,lanes = "pcie-5", "pcie-6"; + nvidia,function = "usb3"; + nvidia,iddq = <0>; + }; + + pcie-x1 { + nvidia,lanes = "pcie-0"; + nvidia,function = "pcie-x1"; + nvidia,iddq = <0>; + }; + + pcie-x4 { + nvidia,lanes = "pcie-1", "pcie-2", + "pcie-3", "pcie-4"; + nvidia,function = "pcie-x4"; + nvidia,iddq = <0>; + }; + + sata { + nvidia,lanes = "sata-0"; + nvidia,function = "sata"; + nvidia,iddq = <0>; + }; + }; + }; + + sdhci at 700b0000 { + status = "okay"; + cd-gpios = <&gpio TEGRA_GPIO(Z, 1) GPIO_ACTIVE_LOW>; + power-gpios = <&gpio TEGRA_GPIO(Z, 3) GPIO_ACTIVE_HIGH>; + bus-width = <4>; + }; + + sdhci at 700b0600 { + status = "okay"; + bus-width = <8>; + non-removable; + }; + + i2c at 7000c400 { + status = "okay"; + clock-frequency = <400000>; + }; + + i2c at 7000c500 { + status = "okay"; + clock-frequency = <400000>; + }; + + i2c at 7000c700 { + status = "okay"; + clock-frequency = <400000>; + }; + + i2c at 7000d000 { + status = "okay"; + clock-frequency = <400000>; + }; + + spi at 70410000 { + status = "okay"; + spi-max-frequency = <80000000>; + }; + + usb at 7d000000 { + status = "okay"; + dr_mode = "peripheral"; + }; + + clocks { + compatible = "simple-bus"; + #address-cells = <1>; + #size-cells = <0>; + + clk32k_in: clock at 0 { + compatible = "fixed-clock"; + reg = <0>; + #clock-cells = <0>; + clock-frequency = <32768>; + }; + }; +};(quoted diff) +0
-0
b/arch/arm/mach-tegra/board2.cindex 787ff97..224efc9 100644arch/arm/mach-tegra/board2.c +25
-0@@ -217,6 +217,31 @@ int board_early_init_f(void)arch_timer_init ();#endif +#if defined(CONFIG_DISABLE_SDMMC1_EARLY ) +/* +* Turn off (reset/disable) SDMMC1 on Nano here, before GPIO INIT. +* We do this because earlier bootloaders have enabled power to +* SDMMC1 on Nano, and toggling power-gpio (PZ3) in pinmux_init() +* results in power being back-driven into the SD-card and SDMMC1 +* HW, which is 'bad' as per the HW team. +* +* From the HW team: "LDO2 from the PMIC has already been set to 3.3v in +* nvtboot/CBoot on Nano (for SD-card boot). So when U-Boot's GPIO_INIT +* table sets PZ3 to OUT0 as per the pinmux spreadsheet, it turns off +* the loadswitch. When PZ3 is 0 and not driving, essentially the SDCard +* voltage turns off. Since the SDCard voltage is no longer there, the +* SDMMC CLK/DAT lines are backdriving into what essentially is a +* powered-off SDCard, that's why the voltage drops from 3.3V to ~1.6V" +* +* Note that this can probably be removed when we change over to storing +* all BL components on QSPI on Nano, and U-Boot then becomes the first +* one to turn on SDMMC1 power. Another fix would be to have CBoot +* disable power/gate SDMMC1 off before handing off to U-Boot/kernel. +*/ +reset_set_enable (PERIPH_ID_SDMMC1 ,1 ); +clock_set_enable (PERIPH_ID_SDMMC1 ,0 );#endif /* +CONFIG_DISABLE_SDMMC1_EARLY */ +pinmux_init ();board_init_uart_f ();arch/arm/mach-tegra/tegra210/Kconfig +7
-0@@ -35,6 +35,12 @@ config TARGET_P2571 help P2571 is a P2530 married to a P1963 I/O board +config TARGET_P3450_0000 + bool "NVIDIA Jetson Nano Developer Kit" + select BOARD_LATE_INIT + help + P3450-0000 is a P3448 CPU board married to a P3449 I/O board. + endchoice config SYS_SOC@@ -44,5 +50,6 @@ source "board/nvidia/e2220-1170/Kconfig" source "board/nvidia/p2371-0000/Kconfig" source "board/nvidia/p2371-2180/Kconfig" source "board/nvidia/p2571/Kconfig" +source "board/nvidia/p3450-0000/Kconfig" endif(quoted diff) +0
-0b/board/nvidia/p3450-0000/Kconfig new file mode 100644 index 0000000..7a08cd8
board/nvidia/p3450-0000/Kconfig new file +12
-0@@ -0,0 +1,12 @@ +if TARGET_P3450_0000 + +config SYS_BOARD + default "p3450-0000" + +config SYS_VENDOR + default "nvidia" + +config SYS_CONFIG_NAME + default "p3450-0000" + +endifboard/nvidia/p3450-0000/MAINTAINERS new file +6
-0@@ -0,0 +1,6 @@ +P3450-0000 BOARD +M: Tom Warren <[email protected]> +S: Maintained +F: board/nvidia/p3450-0000/ +F: include/configs/p3450-0000.h +F: configs/p3450-0000_defconfigboard/nvidia/p3450-0000/Makefile new file +7
-0@@ -0,0 +1,8 @@ +# +# (C) Copyright 2018 +# NVIDIA Corporation <www.nvidia.com> # +# SPDX-License-Identifier: GPL-2.0+ +# + +obj-y += p3450-0000.oboard/nvidia/p3450-0000/p3450-0000.c new file +175
-0@@ -0,0 +1,178 @@ +// SPDX-License-Identifier: GPL-2.0+ +/* +* (C) Copyright 2018-2019 +* NVIDIA Corporation <www.nvidia.com> +* +*/ + +#include <common.h> +#include <fdtdec.h> +#include <i2c.h> +#include <linux/libfdt.h> +#include <pca953x.h> +#include <asm/arch-tegra/cboot.h> +#include <asm/arch/gpio.h> +#include <asm/arch/pinmux.h> +#include "../p2571/max77620_init.h" + +void pin_mux_mmc (void ) +{ +struct udevice *dev; +uchar val; +int ret; + +/* Turn on MAX77620 LDO2 to 3.3V for SD card power */ +debug ("%s: Set LDO2 for VDDIO_SDMMC_AP power to 3.3V\n" , __func__); + ret =i2c_get_chip_for_busnum (0 ,MAX77620_I2C_ADDR_7BIT ,1 , &dev); +if (ret) { +printf ("%s: Cannot find MAX77620 I2C chip\n" , __func__); +return ; + } +/* 0xF2 for 3.3v, enabled: bit7:6 = 11 = enable, bit5:0 = voltage */ + val =0xF2 ; + ret =dm_i2c_write (dev,MAX77620_CNFG1_L2_REG , &val,1 ); +if (ret) +printf ("i2c_write 0 0x3c 0x27 failed: %d\n" , ret); + +/* Disable LDO4 discharge */ + ret =dm_i2c_read (dev,MAX77620_CNFG2_L4_REG , &val,1 ); +if (ret) { +printf ("i2c_read 0 0x3c 0x2c failed: %d\n" , ret); + }else { + val &= ~BIT (1 );/* ADE */ + ret =dm_i2c_write (dev,MAX77620_CNFG2_L4_REG , &val,1 ); +if (ret) +printf ("i2c_write 0 0x3c 0x2c failed: %d\n" , ret); + } + +/* Set MBLPD */ + ret =dm_i2c_read (dev,MAX77620_CNFGGLBL1_REG , &val,1 ); +if (ret) { +printf ("i2c_write 0 0x3c 0x00 failed: %d\n" , ret); + }else { + val |=BIT (6 );/* MBLPD */ + ret =dm_i2c_write (dev,MAX77620_CNFGGLBL1_REG , &val,1 ); +if (ret) +printf ("i2c_write 0 0x3c 0x00 failed: %d\n" , ret); + } +} + +#ifdef CONFIG_PCI_TEGRA +int tegra_pcie_board_init (void ) +{ +struct udevice *dev; +uchar val; +int ret; + +/* Turn on MAX77620 LDO1 to 1.05V for PEX power */ +debug ("%s: Set LDO1 for PEX power to 1.05V\n" , __func__); + ret =i2c_get_chip_for_busnum (0 ,MAX77620_I2C_ADDR_7BIT ,1 , &dev); +if (ret) { +printf ("%s: Cannot find MAX77620 I2C chip\n" , __func__); +return -1 ; + } +/* 0xCA for 1.05v, enabled: bit7:6 = 11 = enable, bit5:0 = voltage */ + val =0xCA ; + ret =dm_i2c_write (dev,MAX77620_CNFG1_L1_REG , &val,1 ); +if (ret) +printf ("i2c_write 0 0x3c 0x25 failed: %d\n" , ret); + +return 0 ; +} +#endif /* PCI */ + +static void ft_mac_address_setup (void *fdt) { +const void *cboot_fdt = (const void *)cboot_boot_x0; +uint8_t mac[ETH_ALEN ], local_mac[ETH_ALEN ]; +const char *path; +int offset, err; + + err =cboot_get_ethaddr (cboot_fdt, local_mac); +if (err <0 ) +memset (local_mac,0 ,ETH_ALEN ); + + path =fdt_get_alias (fdt,"ethernet" ); +if (!path) +return ; + +debug ("ethernet alias found: %s\n" , path); + + offset =fdt_path_offset (fdt, path); +if (offset <0 ) { +printf ("ethernet alias points to absent node %s\n" , path); +return ; + } + +if (is_valid_ethaddr (local_mac)) { + err =fdt_setprop (fdt, offset,"local-mac-address" , local_mac, +ETH_ALEN ); +if (!err) +debug ("Local MAC address set: %pM\n" , local_mac); + } + +if (eth_env_get_enetaddr ("ethaddr" , mac)) { +if (memcmp (local_mac, mac,ETH_ALEN ) !=0 ) { + err =fdt_setprop (fdt, offset,"mac-address" , mac, +ETH_ALEN ); +if (!err) +debug ("MAC address set: %pM\n" , mac); + } + } +} + +static int ft_copy_carveout (void *dst,const void *src,const char +*node) { +struct fdt_memory fb; +int err; + + err =fdtdec_get_carveout (src, node,"memory-region" ,0 , &fb); +if (err <0 ) { +if (err != -FDT_ERR_NOTFOUND ) +printf ("failed to get carveout for %s: %d\n" , node, + err); + +return err; + } + + err =fdtdec_set_carveout (dst, node,"memory-region" ,0 ,"framebuffer" , + &fb); +if (err <0 ) { +printf ("failed to set carveout for %s: %d\n" , node, err); +return err; + } + +return 0 ; +} + +static void ft_carveout_setup (void *fdt) { +const void *cboot_fdt = (const void *)cboot_boot_x0; +static const char *const nodes[] = { +"/host1x at 50000000/dc at 54200000" , +"/host1x at 50000000/dc at 54240000" , + }; +unsigned int i; +int err; + +for (i =0 ; i <ARRAY_SIZE (nodes); i++) { +printf ("copying carveout for %s...\n" , nodes[i]); + + err =ft_copy_carveout (fdt, cboot_fdt, nodes[i]); +if (err <0 ) { +if (err != -FDT_ERR_NOTFOUND ) +printf ("failed to copy carveout for %s: %d\n" , + nodes[i], err); + +continue ; + } + } +} + +int ft_board_setup (void *fdt,bd_t *bd) { +ft_mac_address_setup (fdt); +ft_carveout_setup (fdt); + +return 0 ; +}(quoted diff) +0
-0b/configs/p3450-0000_defconfig new file mode 100644 index 0000000..c861d13
configs/p3450-0000_defconfig new file +64
-0@@ -0,0 +1,64 @@ +CONFIG_ARM=y +CONFIG_TEGRA=y +CONFIG_SYS_TEXT_BASE=0x80080000 +CONFIG_TEGRA210=y +CONFIG_TARGET_P3450_0000=y +CONFIG_NR_DRAM_BANKS=2 +CONFIG_OF_SYSTEM_SETUP=y +CONFIG_OF_BOARD_SETUP=y +CONFIG_CONSOLE_MUX=y +CONFIG_SYS_STDIO_DEREGISTER=y +CONFIG_SYS_PROMPT="Tegra210 (P3450-0000) # " +# CONFIG_CMD_IMI is not set +CONFIG_CMD_DFU=y +# CONFIG_CMD_FLASH is not set +CONFIG_CMD_GPIO=y +CONFIG_CMD_I2C=y +CONFIG_CMD_MMC=y +CONFIG_CMD_PCI=y +CONFIG_CMD_SF=y +CONFIG_CMD_SPI=y +CONFIG_CMD_USB=y +CONFIG_CMD_USB_MASS_STORAGE=y +# CONFIG_CMD_SETEXPR is not set +# CONFIG_CMD_NFS is not set +CONFIG_CMD_EXT4_WRITE=y +CONFIG_OF_LIVE=y +CONFIG_DEFAULT_DEVICE_TREE="tegra210-p3450-0000" +CONFIG_DFU_MMC=y +CONFIG_DFU_RAM=y +CONFIG_DFU_SF=y +CONFIG_SYS_I2C_TEGRA=y +CONFIG_SPI_FLASH=y +CONFIG_SPI_FLASH_MACRONIX=y +CONFIG_SPI_FLASH_USE_4K_SECTORS=y +CONFIG_SF_DEFAULT_MODE=0 +CONFIG_SF_DEFAULT_SPEED=24000000 +CONFIG_RTL8169=y +CONFIG_PCI=y +CONFIG_DM_PCI=y +CONFIG_DM_PCI_COMPAT=y +CONFIG_PCI_TEGRA=y +CONFIG_SYS_NS16550=y +CONFIG_TEGRA114_SPI=y +CONFIG_TEGRA210_QSPI=y +CONFIG_USB=y +CONFIG_DM_USB=y +CONFIG_USB_EHCI_HCD=y +CONFIG_USB_EHCI_TEGRA=y +CONFIG_USB_GADGET=y +CONFIG_USB_GADGET_MANUFACTURER="NVIDIA" +CONFIG_USB_GADGET_VENDOR_NUM=0x0955 +CONFIG_USB_GADGET_PRODUCT_NUM=0x701a +CONFIG_CI_UDC=y +CONFIG_USB_GADGET_DOWNLOAD=y +CONFIG_USB_HOST_ETHER=y +CONFIG_USB_ETHER_ASIX=y +# CONFIG_ENV_IS_IN_MMC is not set +CONFIG_ENV_IS_IN_SPI_FLASH=y +CONFIG_ENV_SIZE=0x2000 +CONFIG_ENV_SECT_SIZE=0x1000 +CONFIG_ENV_OFFSET=0xFFFFE000 +CONFIG_BOOTP_PREFER_SERVERIP=y +CONFIG_DISABLE_SDMMC1_EARLY=y +CONFIG_NVME=y(quoted diff) +0
-0
b/include/configs/p3450-0000.hnew file mode 100644 index 0000000..7f05bebinclude/configs/p3450-0000.h new file +46
-1@@ -0,0 +1,46 @@ +/* SPDX-License-Identifier: GPL-2.0+ */ +/* +* (C) Copyright 2018-2019 NVIDIA Corporation. +*/ + +#ifndef _P3450_0000_H +#define _P3450_0000_H + +#include <linux/sizes.h> + +#include "tegra210-common.h" + +/* High-level configuration options */ +#define CONFIG_TEGRA_BOARD_STRING "NVIDIA P3450-0000" + +/* Board-specific serial config */ +#define CONFIG_TEGRA_ENABLE_UARTA + +/* Only MMC/PXE/DHCP for now, add USB back in later when supported */ +#define BOOT_TARGET_DEVICES (func) \ + func(MMC, mmc, 1) \ + func(MMC, mmc, 0) \ + func(PXE, pxe, na) \ + func(DHCP, dhcp, na) + +/* Environment at end of QSPI, in the VER partition */ +#define CONFIG_ENV_SPI_MAX_HZ 48000000 +#define CONFIG_ENV_SPI_MODE SPI_MODE_0 +#define CONFIG_SPI_FLASH_SIZE (4 << 20) + +#define CONFIG_PREBOOT + +#define BOARD_EXTRA_ENV_SETTINGS \ + "preboot=if test -e mmc 1:1 /u-boot-preboot.scr; then " \ + "load mmc 1:1 ${scriptaddr} /u-boot-preboot.scr; " \ + "source ${scriptaddr}; " \ + "fi\0" + +/* General networking support */ +#include "tegra-common-usb-gadget.h" +#include "tegra-common-post.h" + +/* Crystal is 38.4MHz. clk_m runs at half that rate */ +#define COUNTER_FREQUENCY 19200000 + +#endif /* _P3450_0000_H */ --1.8.2.1.610.g562af5b
----------------------------------------------------------------------
------------- This email message is for the sole use of the intended recipient(s) and may contain confidential information. Any unauthorized review, use, disclosure or distribution is prohibited. If you are not the intended recipient, please contact the sender by reply email and destroy all copies of the original message.
----------------------------------------------------------------------
-------------
PATCH 1/1 ARM: tegra: Add NVIDIA Jetson Nano Developer Kit support
Quoted 10 lines · Tom Warren
-----Original Message-----
From: Peter Robinson <[email protected]>
Sent: Wednesday, March 25, 2020 5:53 AM
To: Tom Warren <[email protected]>
Cc: u-boot at lists.denx.de; Stephen Warren <[email protected]>; Thierry Reding <[email protected]>; Jonathan Hunter <[email protected]>; tomcwarren3959 at gmail.com
Subject: Re: [PATCH] ARM: tegra: Add NVIDIA Jetson Nano Developer Kit supportExternal email: Use caution opening links or attachments
Quoted 8 lines
Hi Tom,
Do you have this and the other patches you've posted on a git branch somewhere, for some reason they're not showing up in patchwork [1] which makes it less straight forward to test.
Peter
[1] http://patchwork.ozlabs.org/project/uboot/list/?q=tegra[Tom] That's weird, I sent them all using git send-email to u-boot at lists.denx.de. But you are right, I don't see any of them on Patchwork. TomR - any idea why?
That is strange, please re-post them and we'll see what happens. If they don't show up right away I can poke people. Thanks!
Signature · 8 lines
Tom -------------- next part -------------- A non-text attachment was scrubbed... Name: signature.asc Type: application/pgp-signature Size: 659 bytes Desc: not available URL: <https://lists.denx.de/pipermail/u-boot/attachments/20200325/fd07ea78/attachment.sig>
PATCH 1/1 ARM: tegra: Add NVIDIA Jetson Nano Developer Kit support
Quoted 1 line
That is strange, please re-post them and we'll see what happens. If they don't show up right away I can poke people. Thanks!
Just resent the Nano patch via:
git send-email 0001*.patch --to u-boot at lists.denx.de --confirm always --annotate --from tomcwarren3959 at gmail.com --cc swarren at nvidia.com --cc treding at nvidia.com --cc jonathanh at nvidia.com --cc twarren at nvidia.com
This time I used my Gmail address in 'from' and put my work address in 'cc'.
Let's see if it shows up in Patchwork.
Tom
-----Original Message-----
From: Tom Rini <[email protected]>
Sent: Wednesday, March 25, 2020 10:56 AM
To: Tom Warren <[email protected]>
Cc: Peter Robinson <[email protected]>; u-boot at lists.denx.de; Stephen Warren <[email protected]>; Thierry Reding <[email protected]>; Jonathan Hunter <[email protected]>; tomcwarren3959 at gmail.com
Subject: Re: [PATCH] ARM: tegra: Add NVIDIA Jetson Nano Developer Kit support
Quoted 13 lines · Tom Warren
-----Original Message-----
From: Peter Robinson <[email protected]>
Sent: Wednesday, March 25, 2020 5:53 AM
To: Tom Warren <[email protected]>
Cc: u-boot at lists.denx.de; Stephen Warren <[email protected]>; Thierry Reding <[email protected]>; Jonathan Hunter <[email protected]>; tomcwarren3959 at gmail.com
Subject: Re: [PATCH] ARM: tegra: Add NVIDIA Jetson Nano Developer Kit supportExternal email: Use caution opening links or attachments
Quoted 8 lines
Hi Tom,
Do you have this and the other patches you've posted on a git branch somewhere, for some reason they're not showing up in patchwork [1] which makes it less straight forward to test.
Peter
[1] http://patchwork.ozlabs.org/project/uboot/list/?q=tegra[Tom] That's weird, I sent them all using git send-email to u-boot at lists.denx.de. But you are right, I don't see any of them on Patchwork. TomR - any idea why?
That is strange, please re-post them and we'll see what happens. If they don't show up right away I can poke people. Thanks!
--
Tom
-----------------------------------------------------------------------------------
This email message is for the sole use of the intended recipient(s) and may contain confidential information. Any unauthorized review, use, disclosure or distribution is prohibited. If you are not the intended recipient, please contact the sender by reply email and destroy all copies of the original message.
-----------------------------------------------------------------------------------
PATCH 1/1 ARM: tegra: Add NVIDIA Jetson Nano Developer Kit support
Quoted 9 lines · Tom Warren
Quoted 1 line
That is strange, please re-post them and we'll see what happens. If they don't show up right away I can poke people. Thanks!
Just resent the Nano patch via:
git send-email 0001*.patch --to u-boot at lists.denx.de --confirm always --annotate --from tomcwarren3959 at gmail.com --cc swarren at nvidia.com --cc treding at nvidia.com --cc jonathanh at nvidia.com --cc twarren at nvidia.com
This time I used my Gmail address in 'from' and put my work address in 'cc'.
Let's see if it shows up in Patchwork.
There's http://patchwork.ozlabs.org/patch/1261582/ now, just that one patch?
Signature · 8 lines
Tom -------------- next part -------------- A non-text attachment was scrubbed... Name: signature.asc Type: application/pgp-signature Size: 659 bytes Desc: not available URL: <https://lists.denx.de/pipermail/u-boot/attachments/20200325/3b3bf245/attachment.sig>
PATCH 1/1 ARM: tegra: Add NVIDIA Jetson Nano Developer Kit support
-----Original Message-----
From: Tom Rini <[email protected]>
Sent: Wednesday, March 25, 2020 11:26 AM
To: Tom Warren <[email protected]>
Cc: Peter Robinson <[email protected]>; u-boot at lists.denx.de; Stephen Warren <[email protected]>; Thierry Reding <[email protected]>; Jonathan Hunter <[email protected]>; tomcwarren3959 at gmail.com
Subject: Re: [PATCH] ARM: tegra: Add NVIDIA Jetson Nano Developer Kit support
Quoted 4 lines · Tom Warren
Quoted 1 line
That is strange, please re-post them and we'll see what happens. If they don't show up right away I can poke people. Thanks!
Just resent the Nano patch via:
Quoted 8 lines
git send-email 0001*.patch --to u-boot at lists.denx.de --confirm always --annotate --from tomcwarren3959 at gmail.com --cc swarren at nvidia.com --cc treding at nvidia.com --cc jonathanh at nvidia.com --cc twarren at nvidia.com
This time I used my Gmail address in 'from' and put my work address in 'cc'.
Let's see if it shows up in Patchwork.
There's http://patchwork.ozlabs.org/patch/1261582/ now, just that one patch?
[Tom] yes, the one I resent above, but using my gmail address (tomcwarren3959) instead of my work address (twarren at nvidia.com). Any idea why that would make any difference? I'll work on resending the others using that address.
--
Tom
-----------------------------------------------------------------------------------
This email message is for the sole use of the intended recipient(s) and may contain confidential information. Any unauthorized review, use, disclosure or distribution is prohibited. If you are not the intended recipient, please contact the sender by reply email and destroy all copies of the original message.
-----------------------------------------------------------------------------------
PATCH 1/1 ARM: tegra: Add NVIDIA Jetson Nano Developer Kit support
Quoted 20 lines · Tom Warren
-----Original Message-----
From: Tom Rini <[email protected]>
Sent: Wednesday, March 25, 2020 11:26 AM
To: Tom Warren <[email protected]>
Cc: Peter Robinson <[email protected]>; u-boot at lists.denx.de; Stephen Warren <[email protected]>; Thierry Reding <[email protected]>; Jonathan Hunter <[email protected]>; tomcwarren3959 at gmail.com
Subject: Re: [PATCH] ARM: tegra: Add NVIDIA Jetson Nano Developer Kit supportQuoted 9 lines · Tom Warren
Quoted 1 line
That is strange, please re-post them and we'll see what happens. If they don't show up right away I can poke people. Thanks!
Just resent the Nano patch via:
git send-email 0001*.patch --to u-boot at lists.denx.de --confirm always --annotate --from tomcwarren3959 at gmail.com --cc swarren at nvidia.com --cc treding at nvidia.com --cc jonathanh at nvidia.com --cc twarren at nvidia.com
Quoted 7 lines
Quoted 3 lines
This time I used my Gmail address in 'from' and put my work address in 'cc'.
Let's see if it shows up in Patchwork.
There's http://patchwork.ozlabs.org/patch/1261582/ now, just that one patch?
[Tom] yes, the one I resent above, but using my gmail address (tomcwarren3959) instead of my work address (twarren at nvidia.com). Any idea why that would make any difference? I'll work on resending the others using that address.
Not sure what went wrong, sorry.
Signature · 8 lines
Tom -------------- next part -------------- A non-text attachment was scrubbed... Name: signature.asc Type: application/pgp-signature Size: 659 bytes Desc: not available URL: <https://lists.denx.de/pipermail/u-boot/attachments/20200325/b15fecc6/attachment.sig>
PATCH 1/1 ARM: tegra: Add NVIDIA Jetson Nano Developer Kit support
In reply to twarren at nvidia.comQuoted 12 lines · twarren at nvidia.com
From: Tom Warren <[email protected]>
The Jetson Nano Developer Kit is a Tegra X1-based development board. It is similar to Jetson TX1 but it is not pin compatible. It features 4GB of LPDDR4, a SPI NOR flash for early boot firmware and an SD card slot used for storage.
HDMI 2.0 or DP 1.2 are available for display, four USB ports (3 USB 2.0 and 1 USB 3.0) can be used to attach a variety of peripherals and a PCI Ethernet controller provides onboard network connectivity. NVMe support has also been added. Env save is at the end of QSPI (4MB-8K).
Quoted 4 lines
A 40-pin header on the board can be used to extend the capabilities and exposed interfaces of the Jetson Nano.
arch/arm/dts/tegra210-p3450-0000.dts | 147 +++++++++++++++++++++++++++++
This filename is consistent with other DT filenames in U-Boot, but there's been a movement downstream to name DT after baseboard plus module rather than combination, so tegra210-p3449-0000+p3448-0000.dts. Either is probably fine for now since this board was released before the push towards the more descriptive naming.
Quoted 16 lines
arch/arm/mach-tegra/board2.c +14
-0+#if defined(CONFIG_DISABLE_SDMMC1_EARLY ) +/* +* Turn off (reset/disable) SDMMC1 on Nano here, before GPIO INIT. +* We do this because earlier bootloaders have enabled power to +* SDMMC1 on Nano, and toggling power-gpio (PZ3) in pinmux_init() +* results in power being back-driven into the SD-card and SDMMC1 +* HW, which is 'bad' as per the HW team. +* +* From the HW team: "LDO2 from the PMIC has already been set to 3.3v in +* nvtboot/CBoot on Nano (for SD-card boot). So when U-Boot's GPIO_INIT +* table sets PZ3 to OUT0 as per the pinmux spreadsheet, it turns off +* the loadswitch. When PZ3 is 0 and not driving, essentially the SDCard +* voltage turns off. Since the SDCard voltage is no longer there, the +* SDMMC CLK/DAT lines are backdriving into what essentially is a
arch/arm/mach-tegra/board2.c int board_early_init_f(void) · line 243
Quoted 10 lines
arch/arm/mach-tegra/board2.c +10
-0+* powered-off SDCard, that's why the voltage drops from 3.3V to ~1.6V" +* +* Note that this can probably be removed when we change over to storing +* all BL components on QSPI on Nano, and U-Boot then becomes the first +* one to turn on SDMMC1 power. Another fix would be to have CBoot +* disable power/gate SDMMC1 off before handing off to U-Boot/kernel. +*/ +reset_set_enable (PERIPH_ID_SDMMC1 ,1 ); +clock_set_enable (PERIPH_ID_SDMMC1 ,0 ); +#endif /* CONFIG_DISABLE_SDMMC1_EARLY */
I imagine we can remove this completely now that cboot does 100% of the pinmux init, so the referenced pinmux_init() function in U-Boot no longer causes a problem?
board/nvidia/p3450-0000/p3450-0000.c
Quoted 3 lines
board/nvidia/p3450-0000/p3450-0000.c +1
-0+static void ft_carveout_setup (void *fdt)
If/when we upstream the DT node/property copying feature, can this code be replaced by simply adding extra nodes/properties to the copy list?
configs/p3450-0000_defconfig
Quoted 3 lines
configs/p3450-0000_defconfig +1
-0+CONFIG_DISABLE_SDMMC1_EARLY=y
We can drop this assuming the code chunk I commented on above gets dropped.
Quoted 1 line
+CONFIG_NVME=y
Does this work already? I thought it was still under development for Tegra.
PATCH 1/1 ARM: tegra: Add NVIDIA Jetson Nano Developer Kit support
-----Original Message-----
From: Stephen Warren <[email protected]>
Sent: Wednesday, March 25, 2020 12:31 PM
To: Tom Warren <[email protected]>
Cc: u-boot at lists.denx.de; Stephen Warren <[email protected]>; Thierry Reding <[email protected]>; Jonathan Hunter <[email protected]>; tomcwarren3959 at gmail.com
Subject: Re: [PATCH] ARM: tegra: Add NVIDIA Jetson Nano Developer Kit support
External email: Use caution opening links or attachments
Quoted 12 lines · twarren at nvidia.com
From: Tom Warren <[email protected]>
The Jetson Nano Developer Kit is a Tegra X1-based development board. It is similar to Jetson TX1 but it is not pin compatible. It features 4GB of LPDDR4, a SPI NOR flash for early boot firmware and an SD card slot used for storage.
HDMI 2.0 or DP 1.2 are available for display, four USB ports (3 USB 2.0 and 1 USB 3.0) can be used to attach a variety of peripherals and a PCI Ethernet controller provides onboard network connectivity. NVMe support has also been added. Env save is at the end of QSPI (4MB-8K).
Quoted 5 lines
A 40-pin header on the board can be used to extend the capabilities and exposed interfaces of the Jetson Nano.
arch/arm/dts/tegra210-p3450-0000.dts | 147+++++++++++++++++++++++++++++
This filename is consistent with other DT filenames in U-Boot, but there's been a movement downstream to name DT after baseboard plus module rather than combination, so tegra210-p3449-0000+p3448-0000.dts. Either is probably fine for now since this board was released before the push towards the more descriptive naming.
[Tom] I'll stick with this naming, someone can float a change to move all Tegra boards to module+baseboard naming later if we so choose. This fits in the current U-Boot naming scheme.
Quoted 17 lines
arch/arm/mach-tegra/board2.c +14
-0+#if defined(CONFIG_DISABLE_SDMMC1_EARLY ) +/* +* Turn off (reset/disable) SDMMC1 on Nano here, before GPIO INIT. +* We do this because earlier bootloaders have enabled power to +* SDMMC1 on Nano, and toggling power-gpio (PZ3) in pinmux_init() +* results in power being back-driven into the SD-card and SDMMC1 +* HW, which is 'bad' as per the HW team. +* +* From the HW team: "LDO2 from the PMIC has already been set to 3.3v in +* nvtboot/CBoot on Nano (for SD-card boot). So when U-Boot's GPIO_INIT +* table sets PZ3 to OUT0 as per the pinmux spreadsheet, it turns off +* the loadswitch. When PZ3 is 0 and not driving, essentially the SDCard +* voltage turns off. Since the SDCard voltage is no longer there, the +* SDMMC CLK/DAT lines are backdriving into what essentially is a
arch/arm/mach-tegra/board2.c int board_early_init_f(void) · line 243
Quoted 10 lines
arch/arm/mach-tegra/board2.c +10
-0+* powered-off SDCard, that's why the voltage drops from 3.3V to ~1.6V" +* +* Note that this can probably be removed when we change over to storing +* all BL components on QSPI on Nano, and U-Boot then becomes the first +* one to turn on SDMMC1 power. Another fix would be to have CBoot +* disable power/gate SDMMC1 off before handing off to U-Boot/kernel. +*/ +reset_set_enable (PERIPH_ID_SDMMC1 ,1 ); +clock_set_enable (PERIPH_ID_SDMMC1 ,0 ); +#endif /* CONFIG_DISABLE_SDMMC1_EARLY */
I imagine we can remove this completely now that cboot does 100% of the pinmux init, so the referenced pinmux_init() function in U-Boot no longer causes a problem?
[Tom] That's a good point, but I'll have to engage w/the HW team to see if they can set up to measure the SD-card signals again w/o this change to see if the back-driving is gone. I'd like to leave it in, though, as a precaution so we don't damage anyone's SD-cards. If/when we can re-measure it, I can float a new patch to remove the SDMMC1_EARLY switch and/or just remove this code entirely.
board/nvidia/p3450-0000/p3450-0000.c
Quoted 4 lines
board/nvidia/p3450-0000/p3450-0000.c +1
-0+static void ft_carveout_setup (void *fdt)
If/when we upstream the DT node/property copying feature, can this code be replaced by simply adding extra nodes/properties to the copy list? [Tom] Good question, I'll look into it. I still need to finesse the FDT copy feature a bit, I'll look at it then.
configs/p3450-0000_defconfig
Quoted 4 lines
configs/p3450-0000_defconfig +1
-0+CONFIG_DISABLE_SDMMC1_EARLY=y
We can drop this assuming the code chunk I commented on above gets dropped.
[Tom] When I can get the HW team to re-measure SD card voltages w/o this I'll float a patch to remove it, assuming it looks good.
Quoted 1 line
+CONFIG_NVME=y
Does this work already? I thought it was still under development for Tegra.
[Tom] Yep, I bought a M.2 E key -> M.2 NVMe adapter for Nano & put a WD Black NVMe stick in it, and I can see/read/write the NVMe device in U-Boot using the 'nvme' commands. And it visible in the kernel. So for T210, it works (in U-Boot). Supporting NVMe in other bootloaders/SoCs that don?t use U-Boot is still a WIP.
--nvpublic