arm: dts: k3-am654: Increase OSPI default frequency to 50MHz
PATCH 1/2 arm: dts: k3-am654: Increase OSPI default frequency to 50MHz
In 1 bit mode OSPI can work at upto 50MHz, this provides before write performance. Therefore increase frequency from 40MHz to 50MHz
--- arch/arm/dts/k3-am654-base-board.dts | 2 +- arch/arm/dts/k3-am654-r5-base-board.dts | 2 +- 2 files changed, 2 insertions(+), 2 deletions(-)
arch/arm/dts/k3-am654-base-board.dts +1 -1
@@ -191,7 +191,7 @@ reg = <0x0>; spi-tx-bus-width = <1>; spi-rx-bus-width = <8>; - spi-max-frequency = <40000000>; + spi-max-frequency = <50000000>; cdns,tshsl-ns = <60>; cdns,tsd2d-ns = <60>; cdns,tchsh-ns = <60>;
arch/arm/dts/k3-am654-r5-base-board.dts +1 -1
@@ -268,7 +268,7 @@ reg = <0x0>; spi-tx-bus-width = <1>; spi-rx-bus-width = <8>; - spi-max-frequency = <40000000>; + spi-max-frequency = <50000000>; cdns,tshsl-ns = <60>; cdns,tsd2d-ns = <60>; cdns,tchsh-ns = <60>;
Signature · 1 line
2.26.0
PATCH 2/2 arm: dts: k3-j721e: Increase OSPI default frequency to 50MHz
In 1 bit mode OSPI can work at upto 50MHz, this provides before write performance. Therefore increase frequency from 40MHz to 50MHz
--- arch/arm/dts/k3-j721e-r5-common-proc-board.dts | 2 +- arch/arm/dts/k3-j721e-som-p0.dtsi | 2 +- 2 files changed, 2 insertions(+), 2 deletions(-)
arch/arm/dts/k3-j721e-r5-common-proc-board.dts +1 -1
@@ -309,7 +309,7 @@ reg = <0x0>; spi-tx-bus-width = <1>; spi-rx-bus-width = <8>; - spi-max-frequency = <40000000>; + spi-max-frequency = <50000000>; cdns,tshsl-ns = <60>; cdns,tsd2d-ns = <60>; cdns,tchsh-ns = <60>;
arch/arm/dts/k3-j721e-som-p0.dtsi +1 -1
@@ -87,7 +87,7 @@ reg = <0x0>; spi-tx-bus-width = <1>; spi-rx-bus-width = <8>; - spi-max-frequency = <40000000>; + spi-max-frequency = <50000000>; cdns,tshsl-ns = <60>; cdns,tsd2d-ns = <60>; cdns,tchsh-ns = <60>;
Signature · 1 line
2.26.0
PATCH 1/2 arm: dts: k3-am654: Increase OSPI default frequency to 50MHz
In reply to Vignesh RaghavendraQuoted 1 line · Vignesh Raghavendra
In 1 bit mode OSPI can work at upto 50MHz, this provides before write
^^^^^^^^^^^^^^^^^^^^^
Provides _what_ before write performance? Did you mean "provides better write performance"? Same in the second patch too.
Quoted 37 lines
performance. Therefore increase frequency from 40MHz to 50MHz
Signed-off-by Vignesh Raghavendra <[email protected]>--- arch/arm/dts/k3-am654-base-board.dts | 2 +- arch/arm/dts/k3-am654-r5-base-board.dts | 2 +- 2 files changed, 2 insertions(+), 2 deletions(-)arch/arm/dts/k3-am654-base-board.dts +1
-1@@ -191,7 +191,7 @@ reg = <0x0>; spi-tx-bus-width = <1>; spi-rx-bus-width = <8>; - spi-max-frequency = <40000000>; + spi-max-frequency = <50000000>; cdns,tshsl-ns = <60>; cdns,tsd2d-ns = <60>; cdns,tchsh-ns = <60>;arch/arm/dts/k3-am654-r5-base-board.dts +1
-1@@ -268,7 +268,7 @@ reg = <0x0>; spi-tx-bus-width = <1>; spi-rx-bus-width = <8>; - spi-max-frequency = <40000000>; + spi-max-frequency = <50000000>; cdns,tshsl-ns = <60>; cdns,tsd2d-ns = <60>; cdns,tchsh-ns = <60>;Signature · 1 line
2.26.0
Signature · 3 lines
Regards, Pratyush Yadav Texas Instruments India
PATCH 1/2 arm: dts: k3-am654: Increase OSPI default frequency to 50MHz
In reply to Vignesh RaghavendraQuoted 4 lines · Vignesh Raghavendra
In 1 bit mode OSPI can work at upto 50MHz, this provides before write performance. Therefore increase frequency from 40MHz to 50MHz
Signed-off-by Vignesh Raghavendra <[email protected]>
Fixed the $commit in both the patches and applied to u-boot-ti.
Thanks and regards,
Lokesh
PATCH 1/2 arm: dts: k3-am654: Increase OSPI default frequency to 50MHz
Quoted 9 lines · Lokesh Vutla
Quoted 4 lines · Vignesh Raghavendra
In 1 bit mode OSPI can work at upto 50MHz, this provides before write performance. Therefore increase frequency from 40MHz to 50MHz
Signed-off-by Vignesh Raghavendra <[email protected]>Fixed the $commit in both the patches and applied to u-boot-ti.
Thanks! I was about to respin with fix same.
Regards
Vignesh