Skip to contentSkip to conversation

configs/nanopi_r1: new defconfig

PATCH New Davide Viti 2 participants 2 messages Oct 27, 2019 – Apr 13, 2020 Arm/Allwinner sunXi SoC support

lore
Share & tools
lore
#0 lore raw

PATCH 1/1 configs/nanopi_r1: new defconfig

Add initial support for Nanopi R1 board with below features:

- U-Boot 2019.01
- Linux 5.0
- Default packages from buildroot

Configuration files taken from Armbian:

https://github.com/armbian/build/blob/master/patch

---
 board/friendlyarm/nanopi-r1/boot.cmd          |   8 +
 board/friendlyarm/nanopi-r1/genimage.cfg      |  36 ++++
 .../nanopi-r1/kernel/linux-extras.config      |   2 +
 .../nanopi-r1/kernel/sun8i-h3-nanopi-r1.dts   | 170 ++++++++++++++++++
 .../friendlyarm/nanopi-r1/nanopi_r1_defconfig |  22 +++
 board/friendlyarm/nanopi-r1/readme.txt        |  29 +++
 .../nanopi-r1/sun8i-h3-nanopi-r1.dts          | 102 +++++++++++
 configs/nanopi_r1_defconfig                   |  49 +++++
 8 files changed, 418 insertions(+)
 create mode 100644 board/friendlyarm/nanopi-r1/boot.cmd
 create mode 100644 board/friendlyarm/nanopi-r1/genimage.cfg
 create mode 100644 board/friendlyarm/nanopi-r1/kernel/linux-extras.config
 create mode 100644 board/friendlyarm/nanopi-r1/kernel/sun8i-h3-nanopi-r1.dts
 create mode 100644 board/friendlyarm/nanopi-r1/nanopi_r1_defconfig
 create mode 100644 board/friendlyarm/nanopi-r1/readme.txt
 create mode 100644 board/friendlyarm/nanopi-r1/sun8i-h3-nanopi-r1.dts
 create mode 100644 configs/nanopi_r1_defconfig
board/friendlyarm/nanopi-r1/boot.cmd new file +8 -0
new file mode 100644
index 0000000000..9f0cdbfe51
@@ -0,0 +1,8 @@
+setenv fdt_high ffffffff
+
+setenv bootargs console=ttyS0,115200 earlyprintk root=/dev/mmcblk0p2 rootwait
+
+fatload mmc 0 $kernel_addr_r zImage
+fatload mmc 0 $fdt_addr_r sun8i-h3-nanopi-r1.dtb
+
+bootz $kernel_addr_r - $fdt_addr_r
board/friendlyarm/nanopi-r1/genimage.cfg new file +36 -0
new file mode 100644
index 0000000000..6f5f35dcd5
@@ -0,0 +1,36 @@
+# Minimal SD card image for the NanoPi M1
+#
+image boot.vfat {
+	vfat {
+		files = {
+			"zImage",
+			"sun8i-h3-nanopi-r1.dtb",
+			"boot.scr"
+		}
+	}
+	size = 10M
+}
+
+image sdcard.img {
+	hdimage {
+	}
+
+	partition u-boot {
+		in-partition-table = "no"
+		image = "u-boot-sunxi-with-spl.bin"
+		offset = 8192
+		size = 1040384 # 1MB - 8192
+	}
+
+	partition boot {
+		partition-type = 0xC
+		bootable = "true"
+		image = "boot.vfat"
+	}
+
+	partition rootfs {
+		partition-type = 0x83
+		image = "rootfs.ext4"
+		size = 512M
+	}
+}
board/friendlyarm/nanopi-r1/kernel/linux-extras.config new file +2 -0
new file mode 100644
index 0000000000..206b3810a7
@@ -0,0 +1,2 @@
+# USB ethernet
+CONFIG_USB_RTL8152=y
board/friendlyarm/nanopi-r1/kernel/sun8i-h3-nanopi-r1.dts new file +170 -0

170 lines not on this page · raw message

board/friendlyarm/nanopi-r1/nanopi_r1_defconfig new file +22 -0
new file mode 100644
index 0000000000..e028b41a46
@@ -0,0 +1,22 @@
+CONFIG_ARM=y
+CONFIG_ARCH_SUNXI=y
+CONFIG_SPL=y
+CONFIG_MACH_SUN8I_H3=y
+CONFIG_DRAM_CLK=408
+CONFIG_DRAM_ZQ=3881979
+CONFIG_DRAM_ODT_EN=y
+CONFIG_MACPWR="PD6"
+# CONFIG_VIDEO_DE2 is not set
+CONFIG_NR_DRAM_BANKS=1
+# CONFIG_SYS_MALLOC_CLEAR_ON_INIT is not set
+CONFIG_CONSOLE_MUX=y
+CONFIG_SYS_CLK_FREQ=480000000
+# CONFIG_CMD_FLASH is not set
+# CONFIG_SPL_DOS_PARTITION is not set
+# CONFIG_SPL_EFI_PARTITION is not set
+CONFIG_DEFAULT_DEVICE_TREE="sun8i-h3-nanopi-r1"
+CONFIG_SUN8I_EMAC=y
+CONFIG_USB_EHCI_HCD=y
+CONFIG_USB_OHCI_HCD=y
+CONFIG_SYS_USB_EVENT_POLL_VIA_INT_QUEUE=y
+CONFIG_MMC_SUNXI_SLOT_EXTRA=2
board/friendlyarm/nanopi-r1/readme.txt new file +29 -0
new file mode 100644
index 0000000000..0ff63df3c7
@@ -0,0 +1,29 @@
+NanoPi R1
+
+Intro
+=====
+
+This default configuration will allow you to start experimenting with the
+buildroot environment for the NanoPi R1. With the current configuration
+it will bring-up the board, and allow access through the serial console.
+
+How to build it
+===============
+
+Configure Buildroot:
+
+    $ make nanopi_r1_defconfig
+
+Compile everything and build the SD card image:
+
+    $ make
+
+How to write the SD card
+========================
+
+Once the build process is finished you will have an image called "sdcard.img"
+in the output/images/ directory.
+
+Copy the bootable "sdcard.img" onto an SD card with "dd":
+
+  $ sudo dd if=output/images/sdcard.img of=/dev/sdX
board/friendlyarm/nanopi-r1/sun8i-h3-nanopi-r1.dts new file +102 -0

102 lines not on this page · raw message

configs/nanopi_r1_defconfig new file +49 -0

49 lines not on this page · raw message

Signature · 1 line
2.20.1
#1 lore raw

PATCH 1/1 configs/nanopi_r1: new defconfig

Hello Davide,

I have finally applied your patch, but I have a number of comments/questions.

Quoted 11 lines · On Sun, 27 Oct 2019 20:50:46 +0100 Davide Viti <[email protected]> wrote:

Add initial support for Nanopi R1 board with below features:

- U-Boot 2019.01
- Linux 5.0
- Default packages from buildroot

Configuration files taken from Armbian:

https://github.com/armbian/build/blob/master/patch

First of all, is this your new e-mail? Our DEVELOPERS file still has:

Davide Viti <[email protected]>

if your e-mail has changed, could you send a patch to update our DEVELOPERS file ?

Quoted 9 lines
 board/friendlyarm/nanopi-r1/boot.cmd          |   8 +
 board/friendlyarm/nanopi-r1/genimage.cfg      |  36 ++++
 .../nanopi-r1/kernel/linux-extras.config      |   2 +
 .../nanopi-r1/kernel/sun8i-h3-nanopi-r1.dts   | 170 ++++++++++++++++++
 .../friendlyarm/nanopi-r1/nanopi_r1_defconfig |  22 +++
 board/friendlyarm/nanopi-r1/readme.txt        |  29 +++
 .../nanopi-r1/sun8i-h3-nanopi-r1.dts          | 102 +++++++++++
 configs/nanopi_r1_defconfig                   |  49 +++++
 8 files changed, 418 insertions(+)

You forgot to update the DEVELOPERS file and the .gitlab-ci.yml file, so I've done that as part of applying your patch.

Quoted 4 lines
 create mode 100644 board/friendlyarm/nanopi-r1/boot.cmd
 create mode 100644 board/friendlyarm/nanopi-r1/genimage.cfg
 create mode 100644 board/friendlyarm/nanopi-r1/kernel/linux-extras.config
 create mode 100644 board/friendlyarm/nanopi-r1/kernel/sun8i-h3-nanopi-r1.dts

These two files were nicely under a kernel/ subdirectory.

Quoted 1 line
 create mode 100644 board/friendlyarm/nanopi-r1/nanopi_r1_defconfig

But this one.

Quoted 2 lines
 create mode 100644 board/friendlyarm/nanopi-r1/readme.txt
 create mode 100644 board/friendlyarm/nanopi-r1/sun8i-h3-nanopi-r1.dts

And this one, which are U-Boot specific were not in a uboot/ sub-directory, so I moved them into a uboot/ sub-directory, and adjusted the defconfig accordingly.

Another question is: your defconfig was done at the time of Linux 5.0 and U-Boot 2019.01, but it seems like support for this board has still not made its way to the upstream Linux kernel and upstream U-Boot. Why so? Could you work with FriendlyArm, or yourself submit support for this board to upstream Linux and U-Boot, so that ultimately, we can drop the .dts files from Buildroot ?

Thanks!

Thomas

Signature · 3 lines
Thomas Petazzoni, CTO, Bootlin
Embedded Linux and Kernel engineering
https://bootlin.com