Skip to contentSkip to conversation

sunxi: add support for Banana Pi P2 Zero board

PATCH New Mizan R 3 participants 5 messages Apr 16, 2020 – May 2, 2020

Subsystems (2)
lore
Share & tools
lore

Mizan R

author
#0 lore raw

PATCH 1/1 sunxi: add support for Banana Pi P2 Zero board

---
 arch/arm/dts/Makefile                         |   1 +
 .../dts/sun8i-h2-plus-bananapi-p2-zero.dts    | 181 ++++++++++++++++++
 configs/Sinovoip_BPI_P2_Zero_defconfig        |  20 ++
 3 files changed, 202 insertions(+)
 create mode 100644 arch/arm/dts/sun8i-h2-plus-bananapi-p2-zero.dts
 create mode 100644 configs/Sinovoip_BPI_P2_Zero_defconfig
arch/arm/dts/Makefile +1 -0
index 62da168ef8..7a43f64b0a 100644
@@ -487,6 +487,7 @@ dtb-$(CONFIG_MACH_SUN8I_A83T) += \
 	sun8i-a83t-tbs-a711.dtb
 dtb-$(CONFIG_MACH_SUN8I_H3) += \
 	sun8i-h2-plus-bananapi-m2-zero.dtb \
+	sun8i-h2-plus-bananapi-p2-zero.dtb \
 	sun8i-h2-plus-libretech-all-h3-cc.dtb \
 	sun8i-h2-plus-orangepi-r1.dtb \
 	sun8i-h2-plus-orangepi-zero.dtb \
arch/arm/dts/sun8i-h2-plus-bananapi-p2-zero.dts new file +181 -0

181 lines not on this page · raw message

configs/Sinovoip_BPI_P2_Zero_defconfig new file +20 -0
new file mode 100644
index 0000000000..cb5b79f254
@@ -0,0 +1,20 @@
+CONFIG_ARM=y
+CONFIG_ARCH_SUNXI=y
+CONFIG_SPL=y
+CONFIG_MACH_SUN8I_H3=y
+CONFIG_DRAM_CLK=408
+CONFIG_DRAM_ZQ=3881979
+CONFIG_DRAM_ODT_EN=y
+CONFIG_NR_DRAM_BANKS=1
+CONFIG_MMC_SUNXI_SLOT_EXTRA=2
+CONFIG_MMC0_CD_PIN=""
+# CONFIG_SYS_MALLOC_CLEAR_ON_INIT is not set
+CONFIG_CONSOLE_MUX=y
+# CONFIG_CMD_FLASH is not set
+# CONFIG_SPL_DOS_PARTITION is not set
+# CONFIG_SPL_ISO_PARTITION is not set
+# CONFIG_SPL_EFI_PARTITION is not set
+CONFIG_DEFAULT_DEVICE_TREE="sun8i-h2-plus-bananapi-p2-zero"
+CONFIG_SUN8I_EMAC=y
+CONFIG_USB_EHCI_HCD=y
+CONFIG_SYS_USB_EVENT_POLL_VIA_INT_QUEUE=y
\ No newline at end of file
Signature · 1 line
2.26.0
#1 lore raw

PATCH 1/1 sunxi: add support for Banana Pi P2 Zero board

Quoted 1 line · Mizan R

commit details?

Quoted 14 lines
---
 arch/arm/dts/Makefile                         |   1 +
 .../dts/sun8i-h2-plus-bananapi-p2-zero.dts    | 181 ++++++++++++++++++
 configs/Sinovoip_BPI_P2_Zero_defconfig        |  20 ++
 3 files changed, 202 insertions(+)
 create mode 100644 arch/arm/dts/sun8i-h2-plus-bananapi-p2-zero.dts
 create mode 100644 configs/Sinovoip_BPI_P2_Zero_defconfig
arch/arm/dts/Makefile +0 -0
index 62da168ef8..7a43f64b0a 100644

arch/arm/dts/Makefile dtb-$(CONFIG_MACH_SUN8I_A83T) += \ · line 490

Quoted 4 lines
arch/arm/dts/Makefile +1 -0
@@ -487,6 +487,7 @@ dtb-$(CONFIG_MACH_SUN8I_A83T) += \
        sun8i-a83t-tbs-a711.dtb
 dtb-$(CONFIG_MACH_SUN8I_H3) += \
        sun8i-h2-plus-bananapi-m2-zero.dtb \
+       sun8i-h2-plus-bananapi-p2-zero.dtb \

Please add the Linux sha1 for this dts file.

Quoted 207 lines
arch/arm/dts/Makefile +0 -0
        sun8i-h2-plus-libretech-all-h3-cc.dtb \
        sun8i-h2-plus-orangepi-r1.dtb \
        sun8i-h2-plus-orangepi-zero.dtb \
arch/arm/dts/sun8i-h2-plus-bananapi-p2-zero.dts new file +181 -0
new file mode 100644
index 0000000000..d28dc8952b
@@ -0,0 +1,181 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Copyright (C) 2020 Mizan R <[email protected]>
+ *
+ * Based on sun8i-h2-plus-bananapi-m2-zero.dts, which is:
+ *   Copyright (C) 2017 Icenowy Zheng <[email protected]>
+ */
+
+/dts-v1/;
+#include "sun8i-h3.dtsi"
+#include "sunxi-common-regulators.dtsi"
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
+
+/ {
+       model = "Banana Pi BPI-P2-Zero";
+       compatible = "sinovoip,bpi-p2-zero", "allwinner,sun8i-h2-plus";
+
+       aliases {
+               serial0 = &uart0;
+               serial1 = &uart1;
+               ethernet0 = &emac;
+       };
+
+       chosen {
+               stdout-path = "serial0:115200n8";
+       };
+
+       connector {
+               compatible = "hdmi-connector";
+               type = "a";
+
+               port {
+                       hdmi_con_in: endpoint {
+                               remote-endpoint = <&hdmi_out_con>;
+                       };
+               };
+       };
+
+       leds {
+               compatible = "gpio-leds";
+               pinctrl-names = "default";
+
+               pwr_led {
+                       label = "bananapi-p2-zero:red:pwr";
+                       linux,default-trigger = "heartbeat";
+                       gpios = <&r_pio 0 10 GPIO_ACTIVE_HIGH>; /* PL10 */
+                       default-state = "on";
+               };
+       };
+
+       gpio_keys {
+               compatible = "gpio-keys";
+               pinctrl-names = "default";
+
+               sw4 {
+                       label = "power";
+                       linux,code = <BTN_0>;
+                       gpios = <&r_pio 0 3 GPIO_ACTIVE_LOW>;
+               };
+       };
+
+       reg_vdd_cpux: vdd-cpux-regulator {
+               compatible = "regulator-gpio";
+               regulator-name = "vdd-cpux";
+               regulator-type = "voltage";
+               regulator-boot-on;
+               regulator-always-on;
+               regulator-min-microvolt = <1100000>;
+               regulator-max-microvolt = <1300000>;
+               regulator-ramp-delay = <50>; /* 4ms */
+
+               gpios = <&r_pio 0 1 GPIO_ACTIVE_HIGH>; /* PL1 */
+               enable-active-high;
+               gpios-states = <0x1>;
+               states = <1100000 0x0
+                         1300000 0x1>;
+       };
+
+       wifi_pwrseq: wifi_pwrseq {
+               compatible = "mmc-pwrseq-simple";
+               pinctrl-names = "default";
+               reset-gpios = <&r_pio 0 7 GPIO_ACTIVE_LOW>; /* PL7 */
+       };
+};
+
+&cpu0 {
+       cpu-supply = <&reg_vdd_cpux>;
+};
+
+&de {
+       status = "okay";
+};
+
+&ehci0 {
+       status = "okay";
+};
+
+&emac {
+       phy-handle = <&int_mii_phy>;
+       phy-mode = "mii";
+       allwinner,leds-active-low;
+       status = "okay";
+};
+
+&hdmi {
+       status = "okay";
+};
+
+&hdmi_out {
+       hdmi_out_con: endpoint {
+               remote-endpoint = <&hdmi_con_in>;
+       };
+};
+
+&mmc0 {
+       vmmc-supply = <&reg_vcc3v3>;
+       bus-width = <4>;
+       cd-gpios = <&pio 5 6 GPIO_ACTIVE_HIGH>; /* PF6 */
+       status = "okay";
+};
+
+&mmc1 {
+       vmmc-supply = <&reg_vcc3v3>;
+       vqmmc-supply = <&reg_vcc3v3>;
+       mmc-pwrseq = <&wifi_pwrseq>;
+       bus-width = <4>;
+       non-removable;
+       status = "okay";
+
+       brcmf: wifi at 1 {
+               reg = <1>;
+               compatible = "brcm,bcm4329-fmac";
+               interrupt-parent = <&pio>;
+               interrupts = <6 10 IRQ_TYPE_LEVEL_LOW>; /* PG10 / EINT10 */
+               interrupt-names = "host-wake";
+       };
+};
+
+&mmc2 {
+       pinctrl-names = "default";
+       pinctrl-0 = <&mmc2_8bit_pins>;
+       vmmc-supply = <&reg_vcc3v3>;
+       vqmmc-supply = <&reg_vcc3v3>;
+       bus-width = <8>;
+       non-removable;
+       status = "okay";
+};
+
+&ohci0 {
+       status = "okay";
+};
+
+&uart0 {
+       pinctrl-names = "default";
+       pinctrl-0 = <&uart0_pa_pins>;
+       status = "okay";
+};
+
+&uart1 {
+       pinctrl-names = "default";
+       pinctrl-0 = <&uart1_pins>, <&uart1_rts_cts_pins>;
+       status = "okay";
+};
+
+&usb_otg {
+       dr_mode = "otg";
+       status = "okay";
+};
+
+&usbphy {
+       usb0_id_det-gpios = <&r_pio 0 6 GPIO_ACTIVE_HIGH>; /* PL6 */
+       /*
+        * There're two micro-USB connectors, one is power-only and another is
+        * OTG. The Vbus of these two connectors are connected together, so
+        * the external USB device will be powered just by the power input
+        * from the power-only USB port.
+        */
+       status = "okay";
+};
configs/Sinovoip_BPI_P2_Zero_defconfig new file +11 -0
new file mode 100644
index 0000000000..cb5b79f254
@@ -0,0 +1,20 @@
+CONFIG_ARM=y
+CONFIG_ARCH_SUNXI=y
+CONFIG_SPL=y
+CONFIG_MACH_SUN8I_H3=y
+CONFIG_DRAM_CLK=408
+CONFIG_DRAM_ZQ=3881979
+CONFIG_DRAM_ODT_EN=y
+CONFIG_NR_DRAM_BANKS=1
+CONFIG_MMC_SUNXI_SLOT_EXTRA=2
+CONFIG_MMC0_CD_PIN=""
+# CONFIG_SYS_MALLOC_CLEAR_ON_INIT is not set

configs/Sinovoip_BPI_P2_Zero_defconfig line 20

Quoted 10 lines
configs/Sinovoip_BPI_P2_Zero_defconfig new file +9 -0
+CONFIG_CONSOLE_MUX=y
+# CONFIG_CMD_FLASH is not set
+# CONFIG_SPL_DOS_PARTITION is not set
+# CONFIG_SPL_ISO_PARTITION is not set
+# CONFIG_SPL_EFI_PARTITION is not set
+CONFIG_DEFAULT_DEVICE_TREE="sun8i-h2-plus-bananapi-p2-zero"
+CONFIG_SUN8I_EMAC=y
+CONFIG_USB_EHCI_HCD=y
+CONFIG_SYS_USB_EVENT_POLL_VIA_INT_QUEUE=y
\ No newline at end of file

Some of defconfigs are moved into respective kconfig files, so please check with existing h3 or h2 board deconfig.

Jagan.

author
#2 lore raw

PATCH 1/1 sunxi: add support for Banana Pi P2 Zero board

Banana Pi P2 Zero is almost identic with Banana Pi M2 Zero with
additional eMMC and PoE functionality
This patch allows uboot to detect ethernet, usb, and eMMC during boot

Bootlog:

U-Boot SPL 2020.04 (Apr 30 2020 - 03:41:48 +0700)
DRAM: 512 MiB
Trying to boot from MMC1

U-Boot 2020.04 (Apr 30 2020 - 03:41:48 +0700) Allwinner Technology

CPU:   Allwinner H3 (SUN8I 1680)
Model: Banana Pi BPI-P2-Zero
DRAM:  512 MiB
MMC:   Device 'mmc at 1c11000': seq 1 is in use by 'mmc at 1c10000'
mmc at 1c0f000: 0, mmc at 1c10000: 2, mmc at 1c11000: 1
Loading Environment from FAT... Unable to use mmc 1:1... In:    serial
Out:   serial
Err:   serial
Net:   phy interface0
eth0: ethernet at 1c30000

starting USB...
Bus usb at 1c1a000: USB EHCI 1.00
scanning bus usb at 1c1a000 for devices...
U-Boot SPL 2020.04 (Apr 30 2020 - 03:41:48 +0700)
DRAM: 512 MiB
Trying to boot from MMC1

U-Boot 2020.04 (Apr 30 2020 - 03:41:48 +0700) Allwinner Technology

CPU:   Allwinner H3 (SUN8I 1680)
Model: Banana Pi BPI-P2-Zero
DRAM:  512 MiB
MMC:   Device 'mmc at 1c11000': seq 1 is in use by 'mmc at 1c10000'
mmc at 1c0f000: 0, mmc at 1c10000: 2, mmc at 1c11000: 1
Loading Environment from FAT... Unable to use mmc 1:1... In:    serial
Out:   serial
Err:   serial
Net:   phy interface0
eth0: ethernet at 1c30000

starting USB...
Bus usb at 1c1a000: USB EHCI 1.00
scanning bus usb at 1c1a000 for devices... 1 USB Device(s) found
scanning usb for storage devices... 0 Storage Device(s) found
switch to partitions #0, OK
mmc0 is current device
Scanning mmc 0:1...
Found U-Boot script /boot.scr
515 bytes read in 2 ms (251 KiB/s)
## Executing script at 43100000
21901 bytes read in 3 ms (7 MiB/s)
3966976 bytes read in 182 ms (20.8 MiB/s)
## Flattened Device Tree blob at 41000000
Booting using the fdt blob at 0x41000000
EHCI failed to shut down host controller.
Loading Device Tree to 49ff7000, end 49fff58c ... OK

Starting kernel ...

---
SHA1SUM for sun8i-h2-plus-bananapi-p2-zero.dts:
c682e1d9faba9d8c959ac526eef0962fc9ebd628 arch/arm/dts/sun8i-h2-plus-bananapi-p2-zero.dts

 arch/arm/dts/Makefile                         |   1 +
 .../dts/sun8i-h2-plus-bananapi-p2-zero.dts    | 181 ++++++++++++++++++
 board/sunxi/MAINTAINERS                       |   5 +
 configs/bananapi_p2_zero_defconfig            |  20 ++
 4 files changed, 207 insertions(+)
 create mode 100644 arch/arm/dts/sun8i-h2-plus-bananapi-p2-zero.dts
 create mode 100644 configs/bananapi_p2_zero_defconfig
arch/arm/dts/Makefile +1 -0
index 820ee973..443d36f9 100644
@@ -516,6 +516,7 @@ dtb-$(CONFIG_MACH_SUN8I_A83T) += \
 	sun8i-a83t-tbs-a711.dtb
 dtb-$(CONFIG_MACH_SUN8I_H3) += \
 	sun8i-h2-plus-bananapi-m2-zero.dtb \
+	sun8i-h2-plus-bananapi-p2-zero.dtb \
 	sun8i-h2-plus-libretech-all-h3-cc.dtb \
 	sun8i-h2-plus-orangepi-r1.dtb \
 	sun8i-h2-plus-orangepi-zero.dtb \
arch/arm/dts/sun8i-h2-plus-bananapi-p2-zero.dts new file +181 -0

181 lines not on this page · raw message

board/sunxi/MAINTAINERS +5 -0
index 1180b86d..e33a5de1 100644
@@ -166,6 +166,11 @@ M:	Icenowy Zheng <[email protected]>
 S:	Maintained
 F:	configs/bananapi_m2_zero_defconfig
 
+BANANAPI P2 ZERO BOARD
+M:	Mizan R <[email protected]>
+S:	Maintained
+F:	configs/bananapi_p2_zero_defconfig
+
 BANANAPI M64
 M:	Jagan Teki <[email protected]>
 S:	Maintained
configs/bananapi_p2_zero_defconfig new file +20 -0
new file mode 100644
index 00000000..aa9a139e
@@ -0,0 +1,20 @@
+CONFIG_ARM=y
+CONFIG_ARCH_SUNXI=y
+CONFIG_SPL=y
+CONFIG_MACH_SUN8I_H3=y
+CONFIG_DRAM_CLK=408
+CONFIG_DRAM_ZQ=3881979
+CONFIG_DRAM_ODT_EN=y
+CONFIG_NR_DRAM_BANKS=1
+CONFIG_MMC_SUNXI_SLOT_EXTRA=2
+CONFIG_MMC0_CD_PIN=""
+# CONFIG_SYS_MALLOC_CLEAR_ON_INIT is not set
+CONFIG_CONSOLE_MUX=y
+# CONFIG_CMD_FLASH is not set
+# CONFIG_SPL_DOS_PARTITION is not set
+# CONFIG_SPL_ISO_PARTITION is not set
+# CONFIG_SPL_EFI_PARTITION is not set
+CONFIG_DEFAULT_DEVICE_TREE="sun8i-h2-plus-bananapi-p2-zero"
+CONFIG_SUN8I_EMAC=y
+CONFIG_USB_EHCI_HCD=y
+# CONFIG_SYS_USB_EVENT_POLL_VIA_INT_QUEUE is not set
Signature · 1 line
2.26.2
#3 lore raw

PATCH 1/1 sunxi: add support for Banana Pi P2 Zero board

Quoted 61 lines · Mizan R

Banana Pi P2 Zero is almost identic with Banana Pi M2 Zero with
additional eMMC and PoE functionality
This patch allows uboot to detect ethernet, usb, and eMMC during boot

Bootlog:

U-Boot SPL 2020.04 (Apr 30 2020 - 03:41:48 +0700)
DRAM: 512 MiB
Trying to boot from MMC1

U-Boot 2020.04 (Apr 30 2020 - 03:41:48 +0700) Allwinner Technology

CPU:   Allwinner H3 (SUN8I 1680)
Model: Banana Pi BPI-P2-Zero
DRAM:  512 MiB
MMC:   Device 'mmc at 1c11000': seq 1 is in use by 'mmc at 1c10000'
mmc at 1c0f000: 0, mmc at 1c10000: 2, mmc at 1c11000: 1
Loading Environment from FAT... Unable to use mmc 1:1... In:    serial
Out:   serial
Err:   serial
Net:   phy interface0
eth0: ethernet at 1c30000

starting USB...
Bus usb at 1c1a000: USB EHCI 1.00
scanning bus usb at 1c1a000 for devices...
U-Boot SPL 2020.04 (Apr 30 2020 - 03:41:48 +0700)
DRAM: 512 MiB
Trying to boot from MMC1

U-Boot 2020.04 (Apr 30 2020 - 03:41:48 +0700) Allwinner Technology

CPU:   Allwinner H3 (SUN8I 1680)
Model: Banana Pi BPI-P2-Zero
DRAM:  512 MiB
MMC:   Device 'mmc at 1c11000': seq 1 is in use by 'mmc at 1c10000'
mmc at 1c0f000: 0, mmc at 1c10000: 2, mmc at 1c11000: 1
Loading Environment from FAT... Unable to use mmc 1:1... In:    serial
Out:   serial
Err:   serial
Net:   phy interface0
eth0: ethernet at 1c30000

starting USB...
Bus usb at 1c1a000: USB EHCI 1.00
scanning bus usb at 1c1a000 for devices... 1 USB Device(s) found
scanning usb for storage devices... 0 Storage Device(s) found
switch to partitions #0, OK
mmc0 is current device
Scanning mmc 0:1...
Found U-Boot script /boot.scr
515 bytes read in 2 ms (251 KiB/s)
## Executing script at 43100000
21901 bytes read in 3 ms (7 MiB/s)
3966976 bytes read in 182 ms (20.8 MiB/s)
## Flattened Device Tree blob at 41000000
Booting using the fdt blob at 0x41000000
EHCI failed to shut down host controller.
Loading Device Tree to 49ff7000, end 49fff58c ... OK

Quoted 1 line

Starting kernel ...

Drop this boot log, please.

Quoted 6 lines

---
SHA1SUM for sun8i-h2-plus-bananapi-p2-zero.dts:
c682e1d9faba9d8c959ac526eef0962fc9ebd628 arch/arm/dts/sun8i-h2-plus-bananapi-p2-zero.dts

You need to add this details into commit message.

commit <sha1> ("text")

Quoted 240 lines
 arch/arm/dts/Makefile                         |   1 +
 .../dts/sun8i-h2-plus-bananapi-p2-zero.dts    | 181 ++++++++++++++++++
 board/sunxi/MAINTAINERS                       |   5 +
 configs/bananapi_p2_zero_defconfig            |  20 ++
 4 files changed, 207 insertions(+)
 create mode 100644 arch/arm/dts/sun8i-h2-plus-bananapi-p2-zero.dts
 create mode 100644 configs/bananapi_p2_zero_defconfig
arch/arm/dts/Makefile +1 -0
index 820ee973..443d36f9 100644
@@ -516,6 +516,7 @@ dtb-$(CONFIG_MACH_SUN8I_A83T) += \
        sun8i-a83t-tbs-a711.dtb
 dtb-$(CONFIG_MACH_SUN8I_H3) += \
        sun8i-h2-plus-bananapi-m2-zero.dtb \
+       sun8i-h2-plus-bananapi-p2-zero.dtb \
        sun8i-h2-plus-libretech-all-h3-cc.dtb \
        sun8i-h2-plus-orangepi-r1.dtb \
        sun8i-h2-plus-orangepi-zero.dtb \
arch/arm/dts/sun8i-h2-plus-bananapi-p2-zero.dts new file +181 -0
new file mode 100644
index 00000000..b253e6e4
@@ -0,0 +1,181 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Copyright (C) 2020 Mizan R <[email protected]>
+ *
+ * Based on sun8i-h2-plus-bananapi-m2-zero.dts, which is:
+ *   Copyright (C) 2017 Icenowy Zheng <[email protected]>
+ */
+
+/dts-v1/;
+#include "sun8i-h3.dtsi"
+#include "sunxi-common-regulators.dtsi"
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
+
+/ {
+       model = "Banana Pi BPI-P2-Zero";
+       compatible = "sinovoip,bpi-p2-zero", "allwinner,sun8i-h2-plus";
+
+       aliases {
+               serial0 = &uart0;
+               serial1 = &uart1;
+               ethernet0 = &emac;
+       };
+
+       chosen {
+               stdout-path = "serial0:115200n8";
+       };
+
+       connector {
+               compatible = "hdmi-connector";
+               type = "a";
+
+               port {
+                       hdmi_con_in: endpoint {
+                               remote-endpoint = <&hdmi_out_con>;
+                       };
+               };
+       };
+
+       leds {
+               compatible = "gpio-leds";
+               pinctrl-names = "default";
+
+               pwr_led {
+                       label = "bananapi-p2-zero:red:pwr";
+                       linux,default-trigger = "heartbeat";
+                       gpios = <&r_pio 0 10 GPIO_ACTIVE_HIGH>; /* PL10 */
+                       default-state = "on";
+               };
+       };
+
+       gpio_keys {
+               compatible = "gpio-keys";
+               pinctrl-names = "default";
+
+               sw4 {
+                       label = "power";
+                       linux,code = <BTN_0>;
+                       gpios = <&r_pio 0 3 GPIO_ACTIVE_LOW>;
+               };
+       };
+
+       reg_vdd_cpux: vdd-cpux-regulator {
+               compatible = "regulator-gpio";
+               regulator-name = "vdd-cpux";
+               regulator-type = "voltage";
+               regulator-boot-on;
+               regulator-always-on;
+               regulator-min-microvolt = <1100000>;
+               regulator-max-microvolt = <1300000>;
+               regulator-ramp-delay = <50>; /* 4ms */
+
+               gpios = <&r_pio 0 1 GPIO_ACTIVE_HIGH>; /* PL1 */
+               enable-active-high;
+               gpios-states = <0x1>;
+               states = <1100000 0x0
+                         1300000 0x1>;
+       };
+
+       wifi_pwrseq: wifi_pwrseq {
+               compatible = "mmc-pwrseq-simple";
+               pinctrl-names = "default";
+               reset-gpios = <&r_pio 0 7 GPIO_ACTIVE_LOW>; /* PL7 */
+       };
+};
+
+&cpu0 {
+       cpu-supply = <&reg_vdd_cpux>;
+};
+
+&de {
+       status = "okay";
+};
+
+&ehci0 {
+       status = "okay";
+};
+
+&emac {
+       phy-handle = <&int_mii_phy>;
+       phy-mode = "mii";
+       allwinner,leds-active-low;
+       status = "okay";
+};
+
+&hdmi {
+       status = "disabled";
+};
+
+&hdmi_out {
+       hdmi_out_con: endpoint {
+               remote-endpoint = <&hdmi_con_in>;
+       };
+};
+
+&mmc0 {
+       vmmc-supply = <&reg_vcc3v3>;
+       bus-width = <4>;
+       cd-gpios = <&pio 5 6 GPIO_ACTIVE_HIGH>; /* PF6 */
+       status = "okay";
+};
+
+&mmc1 {
+       vmmc-supply = <&reg_vcc3v3>;
+       vqmmc-supply = <&reg_vcc3v3>;
+       mmc-pwrseq = <&wifi_pwrseq>;
+       bus-width = <4>;
+       non-removable;
+       status = "okay";
+
+       brcmf: wifi at 1 {
+               reg = <1>;
+               compatible = "brcm,bcm4329-fmac";
+               interrupt-parent = <&pio>;
+               interrupts = <6 10 IRQ_TYPE_LEVEL_LOW>; /* PG10 / EINT10 */
+               interrupt-names = "host-wake";
+       };
+};
+
+&mmc2 {
+       pinctrl-names = "default";
+       pinctrl-0 = <&mmc2_8bit_pins>;
+       vmmc-supply = <&reg_vcc3v3>;
+       vqmmc-supply = <&reg_vcc3v3>;
+       bus-width = <8>;
+       non-removable;
+       status = "okay";
+};
+
+&ohci0 {
+       status = "okay";
+};
+
+&uart0 {
+       pinctrl-names = "default";
+       pinctrl-0 = <&uart0_pa_pins>;
+       status = "okay";
+};
+
+&uart1 {
+       pinctrl-names = "default";
+       pinctrl-0 = <&uart1_pins>, <&uart1_rts_cts_pins>;
+       status = "okay";
+};
+
+&usb_otg {
+       dr_mode = "otg";
+       status = "okay";
+};
+
+&usbphy {
+       usb0_id_det-gpios = <&r_pio 0 6 GPIO_ACTIVE_HIGH>; /* PL6 */
+       /*
+        * There're two micro-USB connectors, one is power-only and another is
+        * OTG. The Vbus of these two connectors are connected together, so
+        * the external USB device will be powered just by the power input
+        * from the power-only USB port.
+        */
+       status = "okay";
+};
board/sunxi/MAINTAINERS +5 -0
index 1180b86d..e33a5de1 100644
@@ -166,6 +166,11 @@ M: Icenowy Zheng <[email protected]>
 S:     Maintained
 F:     configs/bananapi_m2_zero_defconfig
 
+BANANAPI P2 ZERO BOARD
+M:     Mizan R <[email protected]>
+S:     Maintained
+F:     configs/bananapi_p2_zero_defconfig
+
 BANANAPI M64
 M:     Jagan Teki <[email protected]>
 S:     Maintained
configs/bananapi_p2_zero_defconfig new file +10 -0
new file mode 100644
index 00000000..aa9a139e
@@ -0,0 +1,20 @@
+CONFIG_ARM=y
+CONFIG_ARCH_SUNXI=y
+CONFIG_SPL=y
+CONFIG_MACH_SUN8I_H3=y
+CONFIG_DRAM_CLK=408
+CONFIG_DRAM_ZQ=3881979
+CONFIG_DRAM_ODT_EN=y
+CONFIG_NR_DRAM_BANKS=1
+CONFIG_MMC_SUNXI_SLOT_EXTRA=2
+CONFIG_MMC0_CD_PIN=""

configs/bananapi_p2_zero_defconfig line 20

Quoted 10 lines
configs/bananapi_p2_zero_defconfig new file +10 -0
+# CONFIG_SYS_MALLOC_CLEAR_ON_INIT is not set
+CONFIG_CONSOLE_MUX=y
+# CONFIG_CMD_FLASH is not set
+# CONFIG_SPL_DOS_PARTITION is not set
+# CONFIG_SPL_ISO_PARTITION is not set
+# CONFIG_SPL_EFI_PARTITION is not set
+CONFIG_DEFAULT_DEVICE_TREE="sun8i-h2-plus-bananapi-p2-zero"
+CONFIG_SUN8I_EMAC=y
+CONFIG_USB_EHCI_HCD=y
+# CONFIG_SYS_USB_EVENT_POLL_VIA_INT_QUEUE is not set

NAK, seems like you didn't resolve the v1 comments. please take care of next version.

Jagan.

#4 lore raw

PATCH 1/1 sunxi: add support for Banana Pi P2 Zero board

Quoted 10 lines · Jagan Teki
Quoted 6 lines

---
SHA1SUM for sun8i-h2-plus-bananapi-p2-zero.dts:
c682e1d9faba9d8c959ac526eef0962fc9ebd628 arch/arm/dts/sun8i-h2-plus-bananapi-p2-zero.dts

You need to add this details into commit message.

commit <sha1> ("text")

What Jagan means is that you should contribute it to Linux first, and then add in your U-Boot commit log the Linux commit id the DTS was copied from.

Maxime
-------------- next part --------------
A non-text attachment was scrubbed...
Name: signature.asc
Type: application/pgp-signature
Size: 228 bytes
Desc: not available
URL: <https://lists.denx.de/pipermail/u-boot/attachments/20200502/8698a21f/attachment.sig>