net: dsa: sja1105: enable internal pull-down for RX_DV/CRS_DV/RX_CTL and RX_ER
Vladimir Oltean
maintainerPATCH 1/1 net: dsa: sja1105: enable internal pull-down for RX_DV/CRS_DV/RX_CTL and RX_ER
From: Vladimir Oltean <[email protected]>
Some boards do not have the RX_ER MII signal connected. Normally in such situation, those pins would be grounded, but then again, some boards left it electrically floating.
When sending traffic to those switch ports, one can see that the N_SOFERR statistics counter is incrementing once per each packet. The user manual states for this counter that it may count the number of frames "that have the MII error input being asserted prior to or up to the SOF delimiter byte". So the switch MAC is sampling an electrically floating signal, and preventing proper traffic reception because of that.
As a workaround, enable the internal weak pull-downs on the input pads for the MII control signals. This way, a floating signal would be internally tied to ground.
The logic levels of signals which _are_ externally driven should not be bothered by this 40-50 KOhm internal resistor. So it is not an issue to enable the internal pull-down unconditionally, irrespective of PHY interface type (MII, RMII, RGMII, SGMII) and of board layout.
--- drivers/net/dsa/sja1105/sja1105.h | 1 + drivers/net/dsa/sja1105/sja1105_clocking.c | 58 +++++++++++++++++++--- drivers/net/dsa/sja1105/sja1105_spi.c | 2 + 3 files changed, 54 insertions(+), 7 deletions(-)
drivers/net/dsa/sja1105/sja1105.h +1 -0
@@ -49,6 +49,7 @@ struct sja1105_regs {u64 ptpschtm;u64 ptpegr_ts[SJA1105_NUM_PORTS ];u64 pad_mii_tx[SJA1105_NUM_PORTS ]; +u64 pad_mii_rx[SJA1105_NUM_PORTS ];u64 pad_mii_id[SJA1105_NUM_PORTS ];u64 cgu_idiv[SJA1105_NUM_PORTS ];u64 mii_tx_clk[SJA1105_NUM_PORTS ];
drivers/net/dsa/sja1105/sja1105_clocking.c +51 -7
108 lines not on this page · raw message
drivers/net/dsa/sja1105/sja1105_spi.c +2 -0
@@ -443,6 +443,7 @@ static struct sja1105_regs sja1105et_regs = { .rgu = 0x100440, /* UM10944.pdf, Table 86, ACU Register overview */ .pad_mii_tx = {0x100800, 0x100802, 0x100804, 0x100806, 0x100808}, + .pad_mii_rx = {0x100801, 0x100803, 0x100805, 0x100807, 0x100809}, .rmii_pll1 = 0x10000A, .cgu_idiv = {0x10000B, 0x10000C, 0x10000D, 0x10000E, 0x10000F}, .mac = {0x200, 0x202, 0x204, 0x206, 0x208},
@@ -475,6 +476,7 @@ static struct sja1105_regs sja1105pqrs_regs = { .rgu = 0x100440, /* UM10944.pdf, Table 86, ACU Register overview */ .pad_mii_tx = {0x100800, 0x100802, 0x100804, 0x100806, 0x100808}, + .pad_mii_rx = {0x100801, 0x100803, 0x100805, 0x100807, 0x100809}, .pad_mii_id = {0x100810, 0x100811, 0x100812, 0x100813, 0x100814}, .sgmii = 0x1F0000, .rmii_pll1 = 0x10000A,
Signature · 1 line
2.17.1
From: Vladimir Oltean <[email protected]>
Date: Fri, 17 Apr 2020 22:50:52 +0300
Quoted 18 lines
From: Vladimir Oltean <[email protected]>
Some boards do not have the
RX_ERMII signal connected. Normally in such situation, those pins would be grounded, but then again, some boards left it electrically floating.When sending traffic to those switch ports, one can see that the
N_SOFERRstatistics counter is incrementing once per each packet. The user manual states for this counter that it may count the number of frames "that have the MII error input being asserted prior to or up to the SOF delimiter byte". So the switch MAC is sampling an electrically floating signal, and preventing proper traffic reception because of that.As a workaround, enable the internal weak pull-downs on the input pads for the MII control signals. This way, a floating signal would be internally tied to ground.
Quoted 6 lines
The logic levels of signals which _are_ externally driven should not be bothered by this 40-50 KOhm internal resistor. So it is not an issue to enable the internal pull-down unconditionally, irrespective of PHY interface type (MII, RMII, RGMII, SGMII) and of board layout.
Signed-off-by Vladimir Oltean <[email protected]>
Applied, thanks.