imx8qxp_mek: Start with USDHC2 unpowered
Fabio Estevam
reviewerPATCH 1/1 imx8qxp_mek: Start with USDHC2 unpowered
After triggering a "reboot" command in Linux the following hang in SPL is observed:
U-Boot SPL 2020.04 (Apr 15 2020 - 10:49:29 -0300)
Normal Boot
WDT: Not found!
Trying to boot from MMC2_2
spl: mmc init failed with error: -70
SPL: failed to boot from all boot devices
### ERROR ### Please RESET the board ###
This error happens because the CMD_ERR bit is set in the IRQ status register after booting from Linux.
To ensure a fresh start, force the VMMC supply to get unpowered first.
--- board/freescale/imx8qxp_mek/spl.c | 18 ++++++++++++++++++ 1 file changed, 18 insertions(+)
board/freescale/imx8qxp_mek/spl.c +18 -0
@@ -12,9 +12,24 @@#include <dm/uclass-internal.h> #include <dm/device-internal.h> #include <dm/lists.h> +#include <asm/io.h> +#include <asm/gpio.h> +#include <asm/arch/sci/sci.h> +#include <asm/arch/imx8-pins.h> +#include <asm/arch/iomux.h> DECLARE_GLOBAL_DATA_PTR ; +#define GPIO_PAD_CTRL ((SC_PAD_CONFIG_NORMAL << PADRING_CONFIG_SHIFT) | \ + (SC_PAD_ISO_OFF << PADRING_LPCONFIG_SHIFT) | \ + (SC_PAD_28FDSOI_DSE_DV_HIGH << PADRING_DSE_SHIFT) | \ + (SC_PAD_28FDSOI_PS_PU << PADRING_PULL_SHIFT)) + +#define USDHC2_SD_PWR IMX_GPIO_NR(4, 19) +static iomux_cfg_t usdhc2_sd_pwr[] = { +SC_P_USDHC1_RESET_B |MUX_PAD_CTRL (GPIO_PAD_CTRL ), +}; +void spl_board_init (void ) {struct udevice *dev;
@@ -32,6 +47,9 @@ void spl_board_init(void)timer_init (); +imx8_iomux_setup_multiple_pads (usdhc2_sd_pwr,ARRAY_SIZE (usdhc2_sd_pwr)); +gpio_direction_output (USDHC2_SD_PWR ,0 ); +preloader_console_init ();puts ("Normal Boot\n" );
Signature · 1 line
2.17.1
PATCH 1/1 imx8qxp_mek: Start with USDHC2 unpowered
Quoted 12 lines
Subject: [PATCH]
imx8qxp_mek: Start with USDHC2 unpoweredAfter triggering a "reboot" command in Linux the following hang in SPL is observed:
U-Boot SPL 2020.04 (Apr 15 2020 - 10:49:29 -0300) Normal Boot
WDT: Not found!
Trying to boot fromMMC2_2
spl: mmc init failed with error: -70
SPL: failed to boot from all boot devices ### ERROR ### Please RESET the board ###
Quoted 6 lines
This error happens because the
CMD_ERRbit is set in the IRQ status register after booting from Linux.To ensure a fresh start, force the VMMC supply to get unpowered first.
Signed-off-by Fabio Estevam <[email protected]>
Quoted 48 lines
--- board/freescale/imx8qxp_mek/spl.c | 18 ++++++++++++++++++ 1 file changed, 18 insertions(+)board/freescale/imx8qxp_mek/spl.c +17
-0@@ -12,9 +12,24 @@#include <dm/uclass-internal.h> #include <dm/device-internal.h> #include <dm/lists.h> +#include <asm/io.h> +#include <asm/gpio.h> +#include <asm/arch/sci/sci.h> +#include <asm/arch/imx8-pins.h> +#include <asm/arch/iomux.h> DECLARE_GLOBAL_DATA_PTR ; +#define GPIO_PAD_CTRL ((SC_PAD_CONFIG_NORMAL << PADRING_CONFIG_SHIFT) | \ + (SC_PAD_ISO_OFF << PADRING_LPCONFIG_SHIFT) | \ + (SC_PAD_28FDSOI_DSE_DV_HIGH << PADRING_DSE_SHIFT) | \ + (SC_PAD_28FDSOI_PS_PU << PADRING_PULL_SHIFT)) + +#define USDHC2_SD_PWR IMX_GPIO_NR(4, 19) static iomux_cfg_t +usdhc2_sd_pwr[] = { + SC_P_USDHC1_RESET_B | MUX_PAD_CTRL(GPIO_PAD_CTRL), }; +void spl_board_init (void ) {struct udevice *dev;@@ -32,6 +47,9 @@ void spl_board_init(void)timer_init (); +imx8_iomux_setup_multiple_pads (usdhc2_sd_pwr,ARRAY_SIZE (usdhc2_sd_pwr)); +gpio_direction_output (USDHC2_SD_PWR ,0 ); +preloader_console_init ();
puts("Normal Boot\n");
--
2.17.1
PATCH 1/1 imx8qxp_mek: Start with USDHC2 unpowered
In reply to Fabio EstevamQuoted 12 lines
After triggering a "reboot" command in Linux the following hang in SPL is observed:
U-Boot SPL 2020.04 (Apr 15 2020 - 10:49:29 -0300)
Normal Boot
WDT: Not found!
Trying to boot fromMMC2_2
spl: mmc init failed with error: -70
SPL: failed to boot from all boot devices
### ERROR ### Please RESET the board ###
This error happens because theCMD_ERRbit is set in the IRQ status register after booting from Linux.
To ensure a fresh start, force the VMMC supply to get unpowered first.
Quoted 2 lines
Signed-off-by Fabio Estevam <[email protected]>Reviewed-by Peng Fan <[email protected]>
Applied to u-boot-imx, master, thanks !
Best regards,
Stefano Babic
Signature · 5 lines
===================================================================== DENX Software Engineering GmbH, Managing Director: Wolfgang Denk HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany Phone: +49-8142-66989-53 Fax: +49-8142-66989-80 Email: sbabic at denx.de =====================================================================