arm64: dts: qcom: fix pm8150 gpio interrupts
PATCH 1/1 arm64: dts: qcom: fix pm8150 gpio interrupts
This was mistakenly copied from the downstream dts, however the upstream driver works differently.
I only tested this with the pm8150_gpios node (used with volume button), but the 2 others should be the same.
Signed-off-by Jonathan Marek <[email protected]>
--- arch/arm64/boot/dts/qcom/pm8150.dtsi | 14 ++------------ arch/arm64/boot/dts/qcom/pm8150b.dtsi | 14 ++------------ arch/arm64/boot/dts/qcom/pm8150l.dtsi | 14 ++------------ 3 files changed, 6 insertions(+), 36 deletions(-)
arch/arm64/boot/dts/qcom/pm8150.dtsi +2 -12
@@ -73,18 +73,8 @@ pm8150_gpios: gpio@c000 { reg = <0xc000>; gpio-controller; #gpio-cells = <2>; - interrupts = <0x0 0xc0 0x0 IRQ_TYPE_NONE>, - <0x0 0xc1 0x0 IRQ_TYPE_NONE>, - <0x0 0xc2 0x0 IRQ_TYPE_NONE>, - <0x0 0xc3 0x0 IRQ_TYPE_NONE>, - <0x0 0xc4 0x0 IRQ_TYPE_NONE>, - <0x0 0xc5 0x0 IRQ_TYPE_NONE>, - <0x0 0xc6 0x0 IRQ_TYPE_NONE>, - <0x0 0xc7 0x0 IRQ_TYPE_NONE>, - <0x0 0xc8 0x0 IRQ_TYPE_NONE>, - <0x0 0xc9 0x0 IRQ_TYPE_NONE>, - <0x0 0xca 0x0 IRQ_TYPE_NONE>, - <0x0 0xcb 0x0 IRQ_TYPE_NONE>; + interrupt-controller; + #interrupt-cells = <2>; }; };
arch/arm64/boot/dts/qcom/pm8150b.dtsi +2 -12
@@ -62,18 +62,8 @@ pm8150b_gpios: gpio@c000 { reg = <0xc000>; gpio-controller; #gpio-cells = <2>; - interrupts = <0x2 0xc0 0x0 IRQ_TYPE_NONE>, - <0x2 0xc1 0x0 IRQ_TYPE_NONE>, - <0x2 0xc2 0x0 IRQ_TYPE_NONE>, - <0x2 0xc3 0x0 IRQ_TYPE_NONE>, - <0x2 0xc4 0x0 IRQ_TYPE_NONE>, - <0x2 0xc5 0x0 IRQ_TYPE_NONE>, - <0x2 0xc6 0x0 IRQ_TYPE_NONE>, - <0x2 0xc7 0x0 IRQ_TYPE_NONE>, - <0x2 0xc8 0x0 IRQ_TYPE_NONE>, - <0x2 0xc9 0x0 IRQ_TYPE_NONE>, - <0x2 0xca 0x0 IRQ_TYPE_NONE>, - <0x2 0xcb 0x0 IRQ_TYPE_NONE>; + interrupt-controller; + #interrupt-cells = <2>; }; };
arch/arm64/boot/dts/qcom/pm8150l.dtsi +2 -12
@@ -56,18 +56,8 @@ pm8150l_gpios: gpio@c000 { reg = <0xc000>; gpio-controller; #gpio-cells = <2>; - interrupts = <0x4 0xc0 0x0 IRQ_TYPE_NONE>, - <0x4 0xc1 0x0 IRQ_TYPE_NONE>, - <0x4 0xc2 0x0 IRQ_TYPE_NONE>, - <0x4 0xc3 0x0 IRQ_TYPE_NONE>, - <0x4 0xc4 0x0 IRQ_TYPE_NONE>, - <0x4 0xc5 0x0 IRQ_TYPE_NONE>, - <0x4 0xc6 0x0 IRQ_TYPE_NONE>, - <0x4 0xc7 0x0 IRQ_TYPE_NONE>, - <0x4 0xc8 0x0 IRQ_TYPE_NONE>, - <0x4 0xc9 0x0 IRQ_TYPE_NONE>, - <0x4 0xca 0x0 IRQ_TYPE_NONE>, - <0x4 0xcb 0x0 IRQ_TYPE_NONE>; + interrupt-controller; + #interrupt-cells = <2>; }; };
Signature · 1 line
2.26.1
Bjorn Andersson
AppliedQuoted 7 lines · Jonathan Marek
This was mistakenly copied from the downstream dts, however the upstream driver works differently.
I only tested this with the
pm8150_gpiosnode (used with volume button), but the 2 others should be the same.Signed-off-by Jonathan Marek <[email protected]>
Applied, thanks Jonathan
Regards,
Bjorn
Quoted 84 lines
--- arch/arm64/boot/dts/qcom/pm8150.dtsi | 14 ++------------ arch/arm64/boot/dts/qcom/pm8150b.dtsi | 14 ++------------ arch/arm64/boot/dts/qcom/pm8150l.dtsi | 14 ++------------ 3 files changed, 6 insertions(+), 36 deletions(-)arch/arm64/boot/dts/qcom/pm8150.dtsi +2
-12@@ -73,18 +73,8 @@ pm8150_gpios: gpio@c000 { reg = <0xc000>; gpio-controller; #gpio-cells = <2>; - interrupts = <0x0 0xc0 0x0 IRQ_TYPE_NONE>, - <0x0 0xc1 0x0 IRQ_TYPE_NONE>, - <0x0 0xc2 0x0 IRQ_TYPE_NONE>, - <0x0 0xc3 0x0 IRQ_TYPE_NONE>, - <0x0 0xc4 0x0 IRQ_TYPE_NONE>, - <0x0 0xc5 0x0 IRQ_TYPE_NONE>, - <0x0 0xc6 0x0 IRQ_TYPE_NONE>, - <0x0 0xc7 0x0 IRQ_TYPE_NONE>, - <0x0 0xc8 0x0 IRQ_TYPE_NONE>, - <0x0 0xc9 0x0 IRQ_TYPE_NONE>, - <0x0 0xca 0x0 IRQ_TYPE_NONE>, - <0x0 0xcb 0x0 IRQ_TYPE_NONE>; + interrupt-controller; + #interrupt-cells = <2>; }; };arch/arm64/boot/dts/qcom/pm8150b.dtsi +2
-12@@ -62,18 +62,8 @@ pm8150b_gpios: gpio@c000 { reg = <0xc000>; gpio-controller; #gpio-cells = <2>; - interrupts = <0x2 0xc0 0x0 IRQ_TYPE_NONE>, - <0x2 0xc1 0x0 IRQ_TYPE_NONE>, - <0x2 0xc2 0x0 IRQ_TYPE_NONE>, - <0x2 0xc3 0x0 IRQ_TYPE_NONE>, - <0x2 0xc4 0x0 IRQ_TYPE_NONE>, - <0x2 0xc5 0x0 IRQ_TYPE_NONE>, - <0x2 0xc6 0x0 IRQ_TYPE_NONE>, - <0x2 0xc7 0x0 IRQ_TYPE_NONE>, - <0x2 0xc8 0x0 IRQ_TYPE_NONE>, - <0x2 0xc9 0x0 IRQ_TYPE_NONE>, - <0x2 0xca 0x0 IRQ_TYPE_NONE>, - <0x2 0xcb 0x0 IRQ_TYPE_NONE>; + interrupt-controller; + #interrupt-cells = <2>; }; };arch/arm64/boot/dts/qcom/pm8150l.dtsi +2
-12@@ -56,18 +56,8 @@ pm8150l_gpios: gpio@c000 { reg = <0xc000>; gpio-controller; #gpio-cells = <2>; - interrupts = <0x4 0xc0 0x0 IRQ_TYPE_NONE>, - <0x4 0xc1 0x0 IRQ_TYPE_NONE>, - <0x4 0xc2 0x0 IRQ_TYPE_NONE>, - <0x4 0xc3 0x0 IRQ_TYPE_NONE>, - <0x4 0xc4 0x0 IRQ_TYPE_NONE>, - <0x4 0xc5 0x0 IRQ_TYPE_NONE>, - <0x4 0xc6 0x0 IRQ_TYPE_NONE>, - <0x4 0xc7 0x0 IRQ_TYPE_NONE>, - <0x4 0xc8 0x0 IRQ_TYPE_NONE>, - <0x4 0xc9 0x0 IRQ_TYPE_NONE>, - <0x4 0xca 0x0 IRQ_TYPE_NONE>, - <0x4 0xcb 0x0 IRQ_TYPE_NONE>; + interrupt-controller; + #interrupt-cells = <2>; }; };Signature · 1 line
2.26.1