Skip to contentSkip to conversation

net: manually convert files to ReST format - part 1

PATCH In review Mauro Carvalho Chehab 4 participants 43 messages Apr 27, 2020 – Apr 28, 2020

Subsystems (10)
lore
Share & tools
lore
#0 lore raw

cover net: manually convert files to ReST format - part 1

There are very few documents upstream that aren't converted upstream.

This series convert part of the networking text files into ReST. It is part of a bigger set of patches, which were split on parts, in order to make reviewing task easier.

The full series (including those ones) are at:

https://git.linuxtv.org/mchehab/experimental.git/log/?h=net-docs

And the documents, converted to HTML via the building system are at:

https://www.infradead.org/~mchehab/kernel_docs/networking/

Mauro Carvalho Chehab (38):
docs: networking: convert caif files to ReST
docs: networking: convert 6pack.txt to ReST
docs: networking: convert altera_tse.txt to ReST
docs: networking: convert arcnet-hardware.txt to ReST
docs: networking: convert arcnet.txt to ReST
docs: networking: convert atm.txt to ReST
docs: networking: convert ax25.txt to ReST
docs: networking: convert baycom.txt to ReST
docs: networking: convert bonding.txt to ReST
docs: networking: convert cdc_mbim.txt to ReST
docs: networking: convert cops.txt to ReST
docs: networking: convert cxacru.txt to ReST
docs: networking: convert dccp.txt to ReST
docs: networking: convert dctcp.txt to ReST
docs: networking: convert decnet.txt to ReST
docs: networking: convert defza.txt to ReST
docs: networking: convert dns_resolver.txt to ReST
docs: networking: convert driver.txt to ReST
docs: networking: convert eql.txt to ReST
docs: networking: convert fib_trie.txt to ReST
docs: networking: convert filter.txt to ReST
docs: networking: convert fore200e.txt to ReST
docs: networking: convert framerelay.txt to ReST
docs: networking: convert generic-hdlc.txt to ReST
docs: networking: convert generic_netlink.txt to ReST
docs: networking: convert gen_stats.txt to ReST
docs: networking: convert gtp.txt to ReST
docs: networking: convert hinic.txt to ReST
docs: networking: convert ila.txt to ReST
docs: networking: convert ipddp.txt to ReST
docs: networking: convert ip_dynaddr.txt to ReST
docs: networking: convert iphase.txt to ReST
docs: networking: convert ipsec.txt to ReST
docs: networking: convert ip-sysctl.txt to ReST
docs: networking: convert ipv6.txt to ReST
docs: networking: convert ipvlan.txt to ReST
docs: networking: convert ipvs-sysctl.txt to ReST
docs: networking: convert kcm.txt to ReST

 .../admin-guide/kernel-parameters.txt         |   10 +-
 Documentation/admin-guide/sysctl/net.rst      |    4 +-
 Documentation/bpf/index.rst                   |    4 +-
 .../networking/{6pack.txt => 6pack.rst}       |   46 +-
 .../{altera_tse.txt => altera_tse.rst}        |   87 +-
 ...rcnet-hardware.txt => arcnet-hardware.rst} | 2169 +++++++++--------
 .../networking/{arcnet.txt => arcnet.rst}     |  348 +--
 Documentation/networking/{atm.txt => atm.rst} |    6 +
 .../networking/{ax25.txt => ax25.rst}         |    6 +
 .../networking/{baycom.txt => baycom.rst}     |  110 +-
 .../networking/{bonding.txt => bonding.rst}   | 1275 +++++-----
 Documentation/networking/caif/caif.rst        |    2 -
 Documentation/networking/caif/index.rst       |   13 +
 .../caif/{Linux-CAIF.txt => linux_caif.rst}   |   54 +-
 Documentation/networking/caif/spi_porting.rst |  229 ++
 Documentation/networking/caif/spi_porting.txt |  208 --
 .../networking/{cdc_mbim.txt => cdc_mbim.rst} |   76 +-
 Documentation/networking/cops.rst             |   80 +
 Documentation/networking/cops.txt             |   63 -
 .../networking/{cxacru.txt => cxacru.rst}     |   86 +-
 .../networking/{dccp.txt => dccp.rst}         |   39 +-
 .../networking/{dctcp.txt => dctcp.rst}       |   14 +-
 .../networking/{decnet.txt => decnet.rst}     |   77 +-
 .../networking/{defza.txt => defza.rst}       |    8 +-
 .../networking/device_drivers/intel/e100.rst  |    2 +-
 .../networking/device_drivers/intel/ixgb.rst  |    2 +-
 .../{dns_resolver.txt => dns_resolver.rst}    |   52 +-
 .../networking/{driver.txt => driver.rst}     |   22 +-
 Documentation/networking/{eql.txt => eql.rst} |  445 ++--
 .../networking/{fib_trie.txt => fib_trie.rst} |   16 +-
 .../networking/{filter.txt => filter.rst}     |  850 ++++---
 .../networking/{fore200e.txt => fore200e.rst} |    8 +-
 .../{framerelay.txt => framerelay.rst}        |   21 +-
 .../{gen_stats.txt => gen_stats.rst}          |   98 +-
 .../{generic-hdlc.txt => generic-hdlc.rst}    |   86 +-
 ...eneric_netlink.txt => generic_netlink.rst} |    6 +
 Documentation/networking/{gtp.txt => gtp.rst} |   95 +-
 .../networking/{hinic.txt => hinic.rst}       |    5 +-
 Documentation/networking/{ila.txt => ila.rst} |   81 +-
 Documentation/networking/index.rst            |   38 +
 .../{ip-sysctl.txt => ip-sysctl.rst}          |  829 ++++---
 .../{ip_dynaddr.txt => ip_dynaddr.rst}        |   29 +-
 .../networking/{ipddp.txt => ipddp.rst}       |   13 +-
 .../networking/{iphase.txt => iphase.rst}     |  185 +-
 .../networking/{ipsec.txt => ipsec.rst}       |   14 +-
 .../networking/{ipv6.txt => ipv6.rst}         |    8 +-
 .../networking/{ipvlan.txt => ipvlan.rst}     |  159 +-
 .../{ipvs-sysctl.txt => ipvs-sysctl.rst}      |  180 +-
 Documentation/networking/{kcm.txt => kcm.rst} |   83 +-
 Documentation/networking/ltpc.txt             |    2 +-
 Documentation/networking/packet_mmap.txt      |    2 +-
 Documentation/networking/snmp_counter.rst     |    2 +-
 MAINTAINERS                                   |    8 +-
 drivers/atm/Kconfig                           |    4 +-
 drivers/net/Kconfig                           |    4 +-
 drivers/net/appletalk/Kconfig                 |    6 +-
 drivers/net/arcnet/Kconfig                    |    6 +-
 drivers/net/caif/Kconfig                      |    2 +-
 drivers/net/hamradio/Kconfig                  |   10 +-
 drivers/net/wan/Kconfig                       |    4 +-
 net/Kconfig                                   |    2 +-
 net/atm/Kconfig                               |    2 +-
 net/ax25/Kconfig                              |    6 +-
 net/ceph/Kconfig                              |    2 +-
 net/core/gen_stats.c                          |    2 +-
 net/decnet/Kconfig                            |    4 +-
 net/dns_resolver/Kconfig                      |    2 +-
 net/dns_resolver/dns_key.c                    |    2 +-
 net/dns_resolver/dns_query.c                  |    2 +-
 net/ipv4/Kconfig                              |    2 +-
 net/ipv4/icmp.c                               |    2 +-
 net/ipv6/Kconfig                              |    2 +-
 tools/bpf/bpf_asm.c                           |    2 +-
 tools/bpf/bpf_dbg.c                           |    2 +-
 74 files changed, 4656 insertions(+), 3769 deletions(-)
 rename Documentation/networking/{6pack.txt => 6pack.rst} (90%)
 rename Documentation/networking/{altera_tse.txt => altera_tse.rst} (85%)
 rename Documentation/networking/{arcnet-hardware.txt => arcnet-hardware.rst} (66%)
 rename Documentation/networking/{arcnet.txt => arcnet.rst} (76%)
 rename Documentation/networking/{atm.txt => atm.rst} (89%)
 rename Documentation/networking/{ax25.txt => ax25.rst} (91%)
 rename Documentation/networking/{baycom.txt => baycom.rst} (58%)
 rename Documentation/networking/{bonding.txt => bonding.rst} (75%)
 create mode 100644 Documentation/networking/caif/index.rst
 rename Documentation/networking/caif/{Linux-CAIF.txt => linux_caif.rst} (90%)
 create mode 100644 Documentation/networking/caif/spi_porting.rst
 delete mode 100644 Documentation/networking/caif/spi_porting.txt
 rename Documentation/networking/{cdc_mbim.txt => cdc_mbim.rst} (88%)
 create mode 100644 Documentation/networking/cops.rst
 delete mode 100644 Documentation/networking/cops.txt
 rename Documentation/networking/{cxacru.txt => cxacru.rst} (66%)
 rename Documentation/networking/{dccp.txt => dccp.rst} (94%)
 rename Documentation/networking/{dctcp.txt => dctcp.rst} (89%)
 rename Documentation/networking/{decnet.txt => decnet.rst} (87%)
 rename Documentation/networking/{defza.txt => defza.rst} (91%)
 rename Documentation/networking/{dns_resolver.txt => dns_resolver.rst} (89%)
 rename Documentation/networking/{driver.txt => driver.rst} (85%)
 rename Documentation/networking/{eql.txt => eql.rst} (62%)
 rename Documentation/networking/{fib_trie.txt => fib_trie.rst} (96%)
 rename Documentation/networking/{filter.txt => filter.rst} (77%)
 rename Documentation/networking/{fore200e.txt => fore200e.rst} (94%)
 rename Documentation/networking/{framerelay.txt => framerelay.rst} (93%)
 rename Documentation/networking/{gen_stats.txt => gen_stats.rst} (60%)
 rename Documentation/networking/{generic-hdlc.txt => generic-hdlc.rst} (75%)
 rename Documentation/networking/{generic_netlink.txt => generic_netlink.rst} (64%)
 rename Documentation/networking/{gtp.txt => gtp.rst} (79%)
 rename Documentation/networking/{hinic.txt => hinic.rst} (97%)
 rename Documentation/networking/{ila.txt => ila.rst} (82%)
 rename Documentation/networking/{ip-sysctl.txt => ip-sysctl.rst} (83%)
 rename Documentation/networking/{ip_dynaddr.txt => ip_dynaddr.rst} (65%)
 rename Documentation/networking/{ipddp.txt => ipddp.rst} (89%)
 rename Documentation/networking/{iphase.txt => iphase.rst} (50%)
 rename Documentation/networking/{ipsec.txt => ipsec.rst} (90%)
 rename Documentation/networking/{ipv6.txt => ipv6.rst} (93%)
 rename Documentation/networking/{ipvlan.txt => ipvlan.rst} (54%)
 rename Documentation/networking/{ipvs-sysctl.txt => ipvs-sysctl.rst} (62%)
 rename Documentation/networking/{kcm.txt => kcm.rst} (84%)
Signature · 1 line
2.25.4
#1 lore raw

PATCH 1/38 docs: networking: convert caif files to ReST

There are two text files for caif, plus one already converted file.

Convert the two remaining ones to ReST, create a new index.rst file for CAIF, adding it to the main networking documentation index.

---
 Documentation/networking/caif/caif.rst        |   2 -
 Documentation/networking/caif/index.rst       |  13 +
 .../caif/{Linux-CAIF.txt => linux_caif.rst}   |  54 +++--
 Documentation/networking/caif/spi_porting.rst | 229 ++++++++++++++++++
 Documentation/networking/caif/spi_porting.txt | 208 ----------------
 Documentation/networking/index.rst            |   1 +
 drivers/net/caif/Kconfig                      |   2 +-
 7 files changed, 281 insertions(+), 228 deletions(-)
 create mode 100644 Documentation/networking/caif/index.rst
 rename Documentation/networking/caif/{Linux-CAIF.txt => linux_caif.rst} (90%)
 create mode 100644 Documentation/networking/caif/spi_porting.rst
 delete mode 100644 Documentation/networking/caif/spi_porting.txt
Documentation/networking/caif/caif.rst +0 -2
index 07afc8063d4d..a07213030ccf 100644
@@ -1,5 +1,3 @@
-:orphan:
-
 .. SPDX-License-Identifier: GPL-2.0
 .. include:: <isonum.txt>
 
Documentation/networking/caif/index.rst new file +13 -0
new file mode 100644
index 000000000000..86e5b7832ec3
@@ -0,0 +1,13 @@
+.. SPDX-License-Identifier: GPL-2.0
+
+CAIF
+====
+
+Contents:
+
+.. toctree::
+   :maxdepth: 2
+
+   linux_caif
+   caif
+   spi_porting
Documentation/networking/caif/linux_caif.rst renamed from Documentation/networking/caif/Linux-CAIF.txt +37 -17

114 lines not on this page · raw message

Documentation/networking/caif/spi_porting.rst new file +229 -0

229 lines not on this page · raw message

Documentation/networking/caif/spi_porting.txt deleted +0 -208

208 lines not on this page · raw message

Documentation/networking/index.rst +1 -0
index 6538ede29661..5b3421ec25ec 100644
@@ -15,6 +15,7 @@ Contents:
    device_drivers/index
    dsa/index
    devlink/index
+   caif/index
    ethtool-netlink
    ieee802154
    j1939
drivers/net/caif/Kconfig +1 -1
index 9db0570c5beb..1f2f2e8209c3 100644
@@ -28,7 +28,7 @@ config CAIF_SPI_SLAVE
 	  The CAIF Link layer SPI Protocol driver for Slave SPI interface.
 	  This driver implements a platform driver to accommodate for a
 	  platform specific SPI device. A sample CAIF SPI Platform device is
-	  provided in <file:Documentation/networking/caif/spi_porting.txt>.
+	  provided in <file:Documentation/networking/caif/spi_porting.rst>.
 
 config CAIF_SPI_SYNC
 	bool "Next command and length in start of frame"
Signature · 1 line
2.25.4
#2 lore raw

PATCH 2/38 docs: networking: convert 6pack.txt to ReST

In reply to Mauro Carvalho Chehab

- add SPDX header;
- use title markups;
- mark code blocks and literals as such;
- adjust identation, whitespaces and blank lines;
- add to networking/index.rst.

---
 .../networking/{6pack.txt => 6pack.rst}       | 46 +++++++++++++------
 Documentation/networking/index.rst            |  1 +
 drivers/net/hamradio/Kconfig                  |  2 +-
 3 files changed, 33 insertions(+), 16 deletions(-)
 rename Documentation/networking/{6pack.txt => 6pack.rst} (90%)
Documentation/networking/6pack.rst renamed from Documentation/networking/6pack.txt +31 -15
similarity index 90%
rename from Documentation/networking/6pack.txt
rename to Documentation/networking/6pack.rst
index 8f339428fdf4..bc5bf1f1a98f 100644
@@ -1,27 +1,36 @@
+.. SPDX-License-Identifier: GPL-2.0
+
+==============
+6pack Protocol
+==============
+
 This is the 6pack-mini-HOWTO, written by
 
 Andreas Könsgen DG3KQ
-Internet: [email protected]
-AMPR-net: [email protected]
-AX.25:    dg3kq@db0ach.#nrw.deu.eu
+
+:Internet: [email protected]
+:AMPR-net: [email protected]
+:AX.25:    dg3kq@db0ach.#nrw.deu.eu
 
 Last update: April 7, 1998
 
 1. What is 6pack, and what are the advantages to KISS?
+======================================================
 
 6pack is a transmission protocol for data exchange between the PC and
 the TNC over a serial line. It can be used as an alternative to KISS.
 
 6pack has two major advantages:
+
 - The PC is given full control over the radio
   channel. Special control data is exchanged between the PC and the TNC so
   that the PC knows at any time if the TNC is receiving data, if a TNC
   buffer underrun or overrun has occurred, if the PTT is
   set and so on. This control data is processed at a higher priority than
   normal data, so a data stream can be interrupted at any time to issue an
-  important event. This helps to improve the channel access and timing 
-  algorithms as everything is computed in the PC. It would even be possible 
-  to experiment with something completely different from the known CSMA and 
+  important event. This helps to improve the channel access and timing
+  algorithms as everything is computed in the PC. It would even be possible
+  to experiment with something completely different from the known CSMA and
   DAMA channel access methods.
   This kind of real-time control is especially important to supply several
   TNCs that are connected between each other and the PC by a daisy chain
@@ -36,6 +45,7 @@ More details about 6pack are described in the file 6pack.ps that is located
 in the doc directory of the AX.25 utilities package.
 
 2. Who has developed the 6pack protocol?
+========================================
 
 The 6pack protocol has been developed by Ekki Plicht DF4OR, Henning Rech
 DF9IC and Gunter Jost DK7WJ. A driver for 6pack, written by Gunter Jost and
@@ -44,12 +54,14 @@ They have also written a firmware for TNCs to perform the 6pack
 protocol (see section 4 below).
 
 3. Where can I get the latest version of 6pack for LinuX?
+=========================================================
 
 At the moment, the 6pack stuff can obtained via anonymous ftp from
 db0bm.automation.fh-aachen.de. In the directory /incoming/dg3kq,
 there is a file named 6pack.tgz.
 
 4. Preparing the TNC for 6pack operation
+========================================
 
 To be able to use 6pack, a special firmware for the TNC is needed. The EPROM
 of a newly bought TNC does not contain 6pack, so you will have to
@@ -75,12 +87,14 @@ and the status LED are lit for about a second if the firmware initialises
 the TNC correctly.
 
 5. Building and installing the 6pack driver
+===========================================
 
 The driver has been tested with kernel version 2.1.90. Use with older
 kernels may lead to a compilation error because the interface to a kernel
 function has been changed in the 2.1.8x kernels.
 
 How to turn on 6pack support:
+=============================
 
 - In the linux kernel configuration program, select the code maturity level
   options menu and turn on the prompting for development drivers.
@@ -94,27 +108,28 @@ To use the driver, the kissattach program delivered with the AX.25 utilities
 has to be modified.
 
 - Do a cd to the directory that holds the kissattach sources. Edit the
-  kissattach.c file. At the top, insert the following lines:
+  kissattach.c file. At the top, insert the following lines::
 
-  #ifndef N_6PACK
-  #define N_6PACK (N_AX25+1)
-  #endif
+    #ifndef N_6PACK
+    #define N_6PACK (N_AX25+1)
+    #endif
 
-  Then find the line
-   
-  int disc = N_AX25;
+  Then find the line:
+
+    int disc = N_AX25;
 
   and replace N_AX25 by N_6PACK.
 
 - Recompile kissattach. Rename it to spattach to avoid confusions.
 
 Installing the driver:
+----------------------
 
-- Do an insmod 6pack. Look at your /var/log/messages file to check if the 
+- Do an insmod 6pack. Look at your /var/log/messages file to check if the
   module has printed its initialization message.
 
 - Do a spattach as you would launch kissattach when starting a KISS port.
-  Check if the kernel prints the message '6pack: TNC found'. 
+  Check if the kernel prints the message '6pack: TNC found'.
 
 - From here, everything should work as if you were setting up a KISS port.
   The only difference is that the network device that represents
@@ -138,6 +153,7 @@ from the PC to the TNC over the serial line, the status LED if data is
 sent to the PC.
 
 6. Known problems
+=================
 
 When testing the driver with 2.0.3x kernels and
 operating with data rates on the radio channel of 9600 Baud or higher,
Documentation/networking/index.rst +1 -0
index 5b3421ec25ec..dc37fc8d5bee 100644
@@ -37,6 +37,7 @@ Contents:
    tls-offload
    nfc
    6lowpan
+   6pack
 
 .. only::  subproject and html
 
drivers/net/hamradio/Kconfig +1 -1
index 8e05b5c31a77..bf306fed04cc 100644
@@ -30,7 +30,7 @@ config 6PACK
 
 	  Note that this driver is still experimental and might cause
 	  problems. For details about the features and the usage of the
-	  driver, read <file:Documentation/networking/6pack.txt>.
+	  driver, read <file:Documentation/networking/6pack.rst>.
 
 	  To compile this driver as a module, choose M here: the module
 	  will be called 6pack.
Signature · 1 line
2.25.4
#3 lore raw

PATCH 3/38 docs: networking: convert altera_tse.txt to ReST

In reply to Mauro Carvalho Chehab

- add SPDX header;
- use copyright symbol;
- adjust titles and chapters, adding proper markups;
- mark lists as such;
- adjust identation, whitespaces and blank lines;
- add to networking/index.rst.

---
 .../{altera_tse.txt => altera_tse.rst}        | 87 ++++++++++++-------
 Documentation/networking/index.rst            |  1 +
 2 files changed, 56 insertions(+), 32 deletions(-)
 rename Documentation/networking/{altera_tse.txt => altera_tse.rst} (85%)
Documentation/networking/altera_tse.rst renamed from Documentation/networking/altera_tse.txt +55 -32
similarity index 85%
rename from Documentation/networking/altera_tse.txt
rename to Documentation/networking/altera_tse.rst
index 50b8589d12fd..7a7040072e58 100644
@@ -1,6 +1,12 @@
-       Altera Triple-Speed Ethernet MAC driver
+.. SPDX-License-Identifier: GPL-2.0
 
-Copyright (C) 2008-2014 Altera Corporation
+.. include:: <isonum.txt>
+
+=======================================
+Altera Triple-Speed Ethernet MAC driver
+=======================================
+
+Copyright |copy| 2008-2014 Altera Corporation
 
 This is the driver for the Altera Triple-Speed Ethernet (TSE) controllers
 using the SGDMA and MSGDMA soft DMA IP components. The driver uses the
@@ -46,23 +52,33 @@ Jumbo frames are not supported at this time.
 The driver limits PHY operations to 10/100Mbps, and has not yet been fully
 tested for 1Gbps. This support will be added in a future maintenance update.
 
-1) Kernel Configuration
+1. Kernel Configuration
+=======================
+
 The kernel configuration option is ALTERA_TSE:
+
  Device Drivers ---> Network device support ---> Ethernet driver support --->
  Altera Triple-Speed Ethernet MAC support (ALTERA_TSE)
 
-2) Driver parameters list:
-	debug: message level (0: no output, 16: all);
-	dma_rx_num: Number of descriptors in the RX list (default is 64);
-	dma_tx_num: Number of descriptors in the TX list (default is 64).
+2. Driver parameters list
+=========================
+
+	- debug: message level (0: no output, 16: all);
+	- dma_rx_num: Number of descriptors in the RX list (default is 64);
+	- dma_tx_num: Number of descriptors in the TX list (default is 64).
+
+3. Command line options
+=======================
+
+Driver parameters can be also passed in command line by using::
 
-3) Command line options
-Driver parameters can be also passed in command line by using:
 	altera_tse=dma_rx_num:128,dma_tx_num:512
 
-4) Driver information and notes
+4. Driver information and notes
+===============================
 
-4.1) Transmit process
+4.1. Transmit process
+---------------------
 When the driver's transmit routine is called by the kernel, it sets up a
 transmit descriptor by calling the underlying DMA transmit routine (SGDMA or
 MSGDMA), and initiates a transmit operation. Once the transmit is complete, an
@@ -70,7 +86,8 @@ interrupt is driven by the transmit DMA logic. The driver handles the transmit
 completion in the context of the interrupt handling chain by recycling
 resource required to send and track the requested transmit operation.
 
-4.2) Receive process
+4.2. Receive process
+--------------------
 The driver will post receive buffers to the receive DMA logic during driver
 initialization. Receive buffers may or may not be queued depending upon the
 underlying DMA logic (MSGDMA is able queue receive buffers, SGDMA is not able
@@ -79,34 +96,39 @@ received, the DMA logic generates an interrupt. The driver handles a receive
 interrupt by obtaining the DMA receive logic status, reaping receive
 completions until no more receive completions are available.
 
-4.3) Interrupt Mitigation
+4.3. Interrupt Mitigation
+-------------------------
 The driver is able to mitigate the number of its DMA interrupts
 using NAPI for receive operations. Interrupt mitigation is not yet supported
 for transmit operations, but will be added in a future maintenance release.
 
 4.4) Ethtool support
+--------------------
 Ethtool is supported. Driver statistics and internal errors can be taken using:
 ethtool -S ethX command. It is possible to dump registers etc.
 
 4.5) PHY Support
+----------------
 The driver is compatible with PAL to work with PHY and GPHY devices.
 
 4.7) List of source files:
- o Kconfig
- o Makefile
- o altera_tse_main.c: main network device driver
- o altera_tse_ethtool.c: ethtool support
- o altera_tse.h: private driver structure and common definitions
- o altera_msgdma.h: MSGDMA implementation function definitions
- o altera_sgdma.h: SGDMA implementation function definitions
- o altera_msgdma.c: MSGDMA implementation
- o altera_sgdma.c: SGDMA implementation
- o altera_sgdmahw.h: SGDMA register and descriptor definitions
- o altera_msgdmahw.h: MSGDMA register and descriptor definitions
- o altera_utils.c: Driver utility functions
- o altera_utils.h: Driver utility function definitions
+--------------------------
+ - Kconfig
+ - Makefile
+ - altera_tse_main.c: main network device driver
+ - altera_tse_ethtool.c: ethtool support
+ - altera_tse.h: private driver structure and common definitions
+ - altera_msgdma.h: MSGDMA implementation function definitions
+ - altera_sgdma.h: SGDMA implementation function definitions
+ - altera_msgdma.c: MSGDMA implementation
+ - altera_sgdma.c: SGDMA implementation
+ - altera_sgdmahw.h: SGDMA register and descriptor definitions
+ - altera_msgdmahw.h: MSGDMA register and descriptor definitions
+ - altera_utils.c: Driver utility functions
+ - altera_utils.h: Driver utility function definitions
 
-5) Debug Information
+5. Debug Information
+====================
 
 The driver exports debug information such as internal statistics,
 debug information, MAC and DMA registers etc.
@@ -118,17 +140,18 @@ or sees the MAC registers: e.g. using: ethtool -d ethX
 The developer can also use the "debug" module parameter to get
 further debug information.
 
-6) Statistics Support
+6. Statistics Support
+=====================
 
 The controller and driver support a mix of IEEE standard defined statistics,
 RFC defined statistics, and driver or Altera defined statistics. The four
 specifications containing the standard definitions for these statistics are
 as follows:
 
- o IEEE 802.3-2012 - IEEE Standard for Ethernet.
- o RFC 2863 found at http://www.rfc-editor.org/rfc/rfc2863.txt.
- o RFC 2819 found at http://www.rfc-editor.org/rfc/rfc2819.txt.
- o Altera Triple Speed Ethernet User Guide, found at http://www.altera.com
+ - IEEE 802.3-2012 - IEEE Standard for Ethernet.
+ - RFC 2863 found at http://www.rfc-editor.org/rfc/rfc2863.txt.
+ - RFC 2819 found at http://www.rfc-editor.org/rfc/rfc2819.txt.
+ - Altera Triple Speed Ethernet User Guide, found at http://www.altera.com
 
 The statistics supported by the TSE and the device driver are as follows:
 
Documentation/networking/index.rst +1 -0
index dc37fc8d5bee..96ffad845fd9 100644
@@ -38,6 +38,7 @@ Contents:
    nfc
    6lowpan
    6pack
+   altera_tse
 
 .. only::  subproject and html
 
Signature · 1 line
2.25.4
#4 lore raw

PATCH 4/38 docs: networking: convert arcnet-hardware.txt to ReST

In reply to Mauro Carvalho Chehab

- add SPDX header;
- add document title markup;
- add notes markups;
- mark tables as such;
- mark code blocks and literals as such;
- adjust identation, whitespaces and blank lines;
- add to networking/index.rst.

---
 ...rcnet-hardware.txt => arcnet-hardware.rst} | 2169 +++++++++--------
 Documentation/networking/index.rst            |    1 +
 2 files changed, 1136 insertions(+), 1034 deletions(-)
 rename Documentation/networking/{arcnet-hardware.txt => arcnet-hardware.rst} (66%)
Documentation/networking/arcnet-hardware.rst renamed from Documentation/networking/arcnet-hardware.txt +1135 -1034
similarity index 66%
rename from Documentation/networking/arcnet-hardware.txt
rename to Documentation/networking/arcnet-hardware.rst
index 731de411513c..b5a1a020c824 100644
@@ -1,11 +1,15 @@
- 
------------------------------------------------------------------------------
-1) This file is a supplement to arcnet.txt.  Please read that for general
-   driver configuration help.
------------------------------------------------------------------------------
-2) This file is no longer Linux-specific.  It should probably be moved out of
-   the kernel sources.  Ideas?
------------------------------------------------------------------------------
+.. SPDX-License-Identifier: GPL-2.0
+
+===============
+ARCnet Hardware
+===============
+
+.. note::
+
+   1) This file is a supplement to arcnet.txt.  Please read that for general
+      driver configuration help.
+   2) This file is no longer Linux-specific.  It should probably be moved out
+      of the kernel sources.  Ideas?
 
 Because so many people (myself included) seem to have obtained ARCnet cards
 without manuals, this file contains a quick introduction to ARCnet hardware,
@@ -14,8 +18,8 @@ e-mail [email protected] with any settings for your particular card,
 or any other information you have!
 
 
-INTRODUCTION TO ARCNET
-----------------------
+Introduction to ARCnet
+======================
 
 ARCnet is a network type which works in a way similar to popular Ethernet
 networks but which is also different in some very important ways.
@@ -30,7 +34,7 @@ since I only have the 2.5 Mbps variety.  It is probably not going to saturate
 your 100 Mbps card.  Stop complaining. :)
 
 You also cannot connect an ARCnet card to any kind of Ethernet card and
-expect it to work.  
+expect it to work.
 
 There are two "types" of ARCnet - STAR topology and BUS topology.  This
 refers to how the cards are meant to be wired together.  According to most
@@ -71,19 +75,24 @@ although they are generally kept down to the Ethernet-style 1500 bytes.
 For more information on the advantages and disadvantages (mostly the
 advantages) of ARCnet networks, you might try the "ARCnet Trade Association"
 WWW page:
+
 	http://www.arcnet.com
 
 
-CABLING ARCNET NETWORKS
------------------------
+Cabling ARCnet Networks
+=======================
+
+This section was rewritten by
+
+	Vojtech Pavlik     <[email protected]>
 
-This section was rewritten by 
-        Vojtech Pavlik     <[email protected]>
 using information from several people, including:
-        Avery Pennraun     <[email protected]>
- 	Stephen A. Wood    <[email protected]>
- 	John Paul Morrison <[email protected]>
- 	Joachim Koenig     <[email protected]>
+
+	- Avery Pennraun     <[email protected]>
+	- Stephen A. Wood    <[email protected]>
+	- John Paul Morrison <[email protected]>
+	- Joachim Koenig     <[email protected]>
+
 and Avery touched it up a bit, at Vojtech's request.
 
 ARCnet (the classic 2.5 Mbps version) can be connected by two different
@@ -103,13 +112,13 @@ equal to a high impedance one with a terminator installed.
 
 Usually, the ARCnet networks are built up from STAR cards and hubs.  There
 are two types of hubs - active and passive.  Passive hubs are small boxes
-with four BNC connectors containing four 47 Ohm resistors:
+with four BNC connectors containing four 47 Ohm resistors::
 
-   |         | wires
-   R         + junction
--R-+-R-      R 47 Ohm resistors
-   R
-   |
+	   |         | wires
+	   R         + junction
+	-R-+-R-      R 47 Ohm resistors
+	   R
+	   |
 
 The shielding is connected together.  Active hubs are much more complicated;
 they are powered and contain electronics to amplify the signal and send it
@@ -127,14 +136,15 @@ And now to the cabling.  What you can connect together:
 2. A card to a passive hub.  Remember that all unused connectors on the hub
    must be properly terminated with 93 Ohm (or something else if you don't
    have the right ones) terminators.
-   	(Avery's note: oops, I didn't know that.  Mine (TV cable) works
+
+	(Avery's note: oops, I didn't know that.  Mine (TV cable) works
 	anyway, though.)
 
 3. A card to an active hub.  Here is no need to terminate the unused
    connectors except some kind of aesthetic feeling.  But, there may not be
    more than eleven active hubs between any two computers.  That of course
    doesn't limit the number of active hubs on the network.
-   
+
 4. An active hub to another.
 
 5. An active hub to passive hub.
@@ -142,22 +152,22 @@ And now to the cabling.  What you can connect together:
 Remember that you cannot connect two passive hubs together.  The power loss
 implied by such a connection is too high for the net to operate reliably.
 
-An example of a typical ARCnet network:
+An example of a typical ARCnet network::
 
-           R                     S - STAR type card              
+	   R                     S - STAR type card
     S------H--------A-------S    R - Terminator
-           |        |            H - Hub                         
-           |        |            A - Active hub                  
-           |   S----H----S                                       
-           S        |                                            
-                    |                                            
-                    S                                            
-                                                                          
+	   |        |            H - Hub
+	   |        |            A - Active hub
+	   |   S----H----S
+	   S        |
+		    |
+		    S
+
 The BUS topology is very similar to the one used by Ethernet.  The only
 difference is in cable and terminators: they should be 93 Ohm.  Ethernet
 uses 50 Ohm impedance. You use T connectors to put the computers on a single
 line of cable, the bus. You have to put terminators at both ends of the
-cable. A typical BUS ARCnet network looks like:
+cable. A typical BUS ARCnet network looks like::
 
     RT----T------T------T------T------TR
      B    B      B      B      B      B
@@ -168,63 +178,63 @@ cable. A typical BUS ARCnet network looks like:
 
 But that is not all! The two types can be connected together.  According to
 the official documentation the only way of connecting them is using an active
-hub:
+hub::
 
-         A------T------T------TR
-         |      B      B      B
+	 A------T------T------TR
+	 |      B      B      B
      S---H---S
-         |
-         S
+	 |
+	 S
 
 The official docs also state that you can use STAR cards at the ends of
-BUS network in place of a BUS card and a terminator:
+BUS network in place of a BUS card and a terminator::
 
      S------T------T------S
-            B      B
+	    B      B
 
 But, according to my own experiments, you can simply hang a BUS type card
 anywhere in middle of a cable in a STAR topology network.  And more - you
 can use the bus card in place of any star card if you use a terminator. Then
 you can build very complicated networks fulfilling all your needs!  An
-example:
+example::
+
+				  S
+				  |
+	   RT------T-------T------H------S
+	    B      B       B      |
+				  |       R
+    S------A------T-------T-------A-------H------TR
+	   |      B       B       |       |      B
+	   |   S                 BT       |
+	   |   |                  |  S----A-----S
+    S------H---A----S             |       |
+	   |   |      S------T----H---S   |
+	   S   S             B    R       S
 
-                                  S
-                                  |
-           RT------T-------T------H------S
-            B      B       B      |
-                                  |       R
-    S------A------T-------T-------A-------H------TR                    
-           |      B       B       |       |      B                         
-           |   S                 BT       |                                 
-           |   |                  |  S----A-----S
-    S------H---A----S             |       | 
-           |   |      S------T----H---S   |
-           S   S             B    R       S  
-                                                               
 A basically different cabling scheme is used with Twisted Pair cabling. Each
 of the TP cards has two RJ (phone-cord style) connectors.  The cards are
 then daisy-chained together using a cable connecting every two neighboring
 cards.  The ends are terminated with RJ 93 Ohm terminators which plug into
-the empty connectors of cards on the ends of the chain.  An example:
+the empty connectors of cards on the ends of the chain.  An example::
 
-          ___________   ___________
-      _R_|_         _|_|_         _|_R_  
-     |     |       |     |       |     |      
-     |Card |       |Card |       |Card |     
-     |_____|       |_____|       |_____|          
+	  ___________   ___________
+      _R_|_         _|_|_         _|_R_
+     |     |       |     |       |     |
+     |Card |       |Card |       |Card |
+     |_____|       |_____|       |_____|
 
 
 There are also hubs for the TP topology.  There is nothing difficult
 involved in using them; you just connect a TP chain to a hub on any end or
-even at both.  This way you can create almost any network configuration. 
+even at both.  This way you can create almost any network configuration.
 The maximum of 11 hubs between any two computers on the net applies here as
-well.  An example:
+well.  An example::
 
     RP-------P--------P--------H-----P------P-----PR
-                               |
+			       |
       RP-----H--------P--------H-----P------PR
-             |                 |
-             PR                PR
+	     |                 |
+	     PR                PR
 
     R - RJ Terminator
     P - TP Card
@@ -234,11 +244,13 @@ Like any network, ARCnet has a limited cable length.  These are the maximum
 cable lengths between two active ends (an active end being an active hub or
 a STAR card).
 
+		========== ======= ===========
 		RG-62       93 Ohm up to 650 m
 		RG-59/U     75 Ohm up to 457 m
 		RG-11/U     75 Ohm up to 533 m
 		IBM Type 1 150 Ohm up to 200 m
 		IBM Type 3 100 Ohm up to 100 m
+		========== ======= ===========
 
 The maximum length of all cables connected to a passive hub is limited to 65
 meters for RG-62 cabling; less for others.  You can see that using passive
@@ -248,8 +260,8 @@ most distant points of the net is limited to 3000 meters. The maximum length
 of a TP cable between two cards/hubs is 650 meters.
 
 
-SETTING THE JUMPERS
--------------------
+Setting the Jumpers
+===================
 
 All ARCnet cards should have a total of four or five different settings:
 
@@ -261,43 +273,51 @@ All ARCnet cards should have a total of four or five different settings:
     eating net connections on my system (at least) otherwise.  My guess is
     this may be because, if your card is at 0x2E0, probing for a serial port
     at 0x2E8 will reset the card and probably mess things up royally.
+
 	- Avery's favourite: 0x300.
 
   - the IRQ: on  8-bit cards, it might be 2 (9), 3, 4, 5, or 7.
-             on 16-bit cards, it might be 2 (9), 3, 4, 5, 7, or 10-15.
-             
+	     on 16-bit cards, it might be 2 (9), 3, 4, 5, 7, or 10-15.
+
     Make sure this is different from any other card on your system.  Note
     that IRQ2 is the same as IRQ9, as far as Linux is concerned.  You can
     "cat /proc/interrupts" for a somewhat complete list of which ones are in
     use at any given time.  Here is a list of common usages from Vojtech
     Pavlik <[email protected]>:
-    	("Not on bus" means there is no way for a card to generate this
+
+	("Not on bus" means there is no way for a card to generate this
 	interrupt)
-	IRQ  0 - Timer 0 (Not on bus)
-	IRQ  1 - Keyboard (Not on bus)
-	IRQ  2 - IRQ Controller 2 (Not on bus, nor does interrupt the CPU)
-	IRQ  3 - COM2
-	IRQ  4 - COM1
-	IRQ  5 - FREE (LPT2 if you have it; sometimes COM3; maybe PLIP)
-	IRQ  6 - Floppy disk controller
-	IRQ  7 - FREE (LPT1 if you don't use the polling driver; PLIP) 
-	IRQ  8 - Realtime Clock Interrupt (Not on bus)
-	IRQ  9 - FREE (VGA vertical sync interrupt if enabled)
-	IRQ 10 - FREE
-	IRQ 11 - FREE
-	IRQ 12 - FREE
-	IRQ 13 - Numeric Coprocessor (Not on bus)
-	IRQ 14 - Fixed Disk Controller
-	IRQ 15 - FREE (Fixed Disk Controller 2 if you have it) 
-	
-	Note: IRQ 9 is used on some video cards for the "vertical retrace"
-	interrupt.  This interrupt would have been handy for things like
-	video games, as it occurs exactly once per screen refresh, but
-	unfortunately IBM cancelled this feature starting with the original
-	VGA and thus many VGA/SVGA cards do not support it.  For this
-	reason, no modern software uses this interrupt and it can almost
-	always be safely disabled, if your video card supports it at all.
-	
+
+	======   =========================================================
+	IRQ  0   Timer 0 (Not on bus)
+	IRQ  1   Keyboard (Not on bus)
+	IRQ  2   IRQ Controller 2 (Not on bus, nor does interrupt the CPU)
+	IRQ  3   COM2
+	IRQ  4   COM1
+	IRQ  5   FREE (LPT2 if you have it; sometimes COM3; maybe PLIP)
+	IRQ  6   Floppy disk controller
+	IRQ  7   FREE (LPT1 if you don't use the polling driver; PLIP)
+	IRQ  8   Realtime Clock Interrupt (Not on bus)
+	IRQ  9   FREE (VGA vertical sync interrupt if enabled)
+	IRQ 10   FREE
+	IRQ 11   FREE
+	IRQ 12   FREE
+	IRQ 13   Numeric Coprocessor (Not on bus)
+	IRQ 14   Fixed Disk Controller
+	IRQ 15   FREE (Fixed Disk Controller 2 if you have it)
+	======   =========================================================
+
+
+	.. note::
+
+	   IRQ 9 is used on some video cards for the "vertical retrace"
+	   interrupt.  This interrupt would have been handy for things like
+	   video games, as it occurs exactly once per screen refresh, but
+	   unfortunately IBM cancelled this feature starting with the original
+	   VGA and thus many VGA/SVGA cards do not support it.  For this
+	   reason, no modern software uses this interrupt and it can almost
+	   always be safely disabled, if your video card supports it at all.
+
 	If your card for some reason CANNOT disable this IRQ (usually there
 	is a jumper), one solution would be to clip the printed circuit
 	contact on the board: it's the fourth contact from the left on the
@@ -308,14 +328,18 @@ All ARCnet cards should have a total of four or five different settings:
   - the memory address:  Unlike most cards, ARCnets use "shared memory" for
     copying buffers around.  Make SURE it doesn't conflict with any other
     used memory in your system!
+
+    ::
+
 	A0000		- VGA graphics memory (ok if you don't have VGA)
-        B0000		- Monochrome text mode
-        C0000		\  One of these is your VGA BIOS - usually C0000.
-        E0000		/
-        F0000		- System BIOS
+	B0000		- Monochrome text mode
+	C0000		\  One of these is your VGA BIOS - usually C0000.
+	E0000		/
+	F0000		- System BIOS
 
     Anything less than 0xA0000 is, well, a BAD idea since it isn't above
     640k.
+
 	- Avery's favourite: 0xD0000
 
   - the station address:  Every ARCnet card has its own "unique" network
@@ -326,6 +350,7 @@ All ARCnet cards should have a total of four or five different settings:
     neat stuff will probably happen if you DO use them).  By the way, if you
     haven't already guessed, don't set this the same as any other ARCnet on
     your network!
+
 	- Avery's favourite:  3 and 4.  Not that it matters.
 
   - There may be ETS1 and ETS2 settings.  These may or may not make a
@@ -336,28 +361,34 @@ All ARCnet cards should have a total of four or five different settings:
     requirement here is that all cards on the network with ETS1 and ETS2
     jumpers have them in the same position.  Chris Hindy <[email protected]>
     sent in a chart with actual values for this:
+
+	======= ======= =============== ====================
 	ET1	ET2	Response Time	Reconfiguration Time
-	---	---	-------------	--------------------
+	======= ======= =============== ====================
 	open	open	74.7us		840us
 	open	closed	283.4us		1680us
 	closed	open	561.8us		1680us
 	closed	closed	1118.6us	1680us
-    
+	======= ======= =============== ====================
+
     Make sure you set ETS1 and ETS2 to the SAME VALUE for all cards on your
     network.
-    
-Also, on many cards (not mine, though) there are red and green LED's. 
+
+Also, on many cards (not mine, though) there are red and green LED's.
 Vojtech Pavlik <[email protected]> tells me this is what they mean:
+
+	=============== =============== =====================================
 	GREEN           RED             Status
-	-----		---		------
+	=============== =============== =====================================
 	OFF             OFF             Power off
 	OFF             Short flashes   Cabling problems (broken cable or not
-					  terminated)
+					terminated)
 	OFF (short)     ON              Card init
 	ON              ON              Normal state - everything OK, nothing
-					  happens
+					happens
 	ON              Long flashes    Data transfer
 	ON              OFF             Never happens (maybe when wrong ID)
+	=============== =============== =====================================
 
 
 The following is all the specific information people have sent me about
@@ -366,7 +397,7 @@ huge amounts of duplicated information.  I have no time to fix it.  If you
 want to, PLEASE DO!  Just send me a 'diff -u' of all your changes.
 
 The model # is listed right above specifics for that card, so you should be
-able to use your text viewer's "search" function to find the entry you want. 
+able to use your text viewer's "search" function to find the entry you want.
 If you don't KNOW what kind of card you have, try looking through the
 various diagrams to see if you can tell.
 
@@ -378,8 +409,9 @@ model that is, please e-mail me to say so.
 
 Cards Listed in this file (in this order, mostly):
 
+	=============== ======================= ====
 	Manufacturer	Model #			Bits
-	------------	-------			----
+	=============== ======================= ====
 	SMC		PC100			8
 	SMC		PC110			8
 	SMC		PC120			8
@@ -404,17 +436,19 @@ Cards Listed in this file (in this order, mostly):
 	No Name		Taiwan R.O.C?		8
 	No Name		Model 9058		8
 	Tiara		Tiara Lancard?		8
-	
+	=============== ======================= ====
 
-** SMC = Standard Microsystems Corp.
-** CNet Tech = CNet Technology, Inc.
 
+* SMC = Standard Microsystems Corp.
+* CNet Tech = CNet Technology, Inc.
 
 Unclassified Stuff
-------------------
+==================
+
   - Please send any other information you can find.
-  
-  - And some other stuff (more info is welcome!):
+
+  - And some other stuff (more info is welcome!)::
+
      From: [email protected] (Timo Hilbrink)
      To: [email protected] (Avery Pennarun)
      Date: Wed, 26 Oct 1994 02:10:32 +0000 (GMT)
@@ -423,7 +457,7 @@ Unclassified Stuff
      [...parts deleted...]
 
      About the jumpers: On my PC130 there is one more jumper, located near the
-     cable-connector and it's for changing to star or bus topology; 
+     cable-connector and it's for changing to star or bus topology;
      closed: star - open: bus
      On the PC500 are some more jumper-pins, one block labeled with RX,PDN,TXI
      and another with ALE,LA17,LA18,LA19 these are undocumented..
@@ -432,136 +466,130 @@ Unclassified Stuff
 
      --- CUT ---
 
+Standard Microsystems Corp (SMC)
+================================
+
+PC100, PC110, PC120, PC130 (8-bit cards) and PC500, PC600 (16-bit cards)
+------------------------------------------------------------------------
 
-** Standard Microsystems Corp (SMC) **
-PC100, PC110, PC120, PC130 (8-bit cards)
-PC500, PC600 (16-bit cards)
----------------------------------
   - mainly from Avery Pennarun <[email protected]>.  Values depicted
     are from Avery's setup.
   - special thanks to Timo Hilbrink <[email protected]> for noting that PC120,
-    130, 500, and 600 all have the same switches as Avery's PC100. 
+    130, 500, and 600 all have the same switches as Avery's PC100.
     PC500/600 have several extra, undocumented pins though. (?)
   - PC110 settings were verified by Stephen A. Wood <[email protected]>
   - Also, the JP- and S-numbers probably don't match your card exactly.  Try
     to find jumpers/switches with the same number of settings - it's
     probably more reliable.
-  
-
-     JP5		       [|]    :    :    :    :
-(IRQ Setting)		      IRQ2  IRQ3 IRQ4 IRQ5 IRQ7
-		Put exactly one jumper on exactly one set of pins.
-
-
-                          1  2   3  4  5  6   7  8  9 10
-     S1                /----------------------------------\
-(I/O and Memory        |  1  1 * 0  0  0  0 * 1  1  0  1  |
- addresses)            \----------------------------------/
-                          |--|   |--------|   |--------|
-                          (a)       (b)           (m)
-                          
-                WARNING.  It's very important when setting these which way
-                you're holding the card, and which way you think is '1'!
-                
-                If you suspect that your settings are not being made
-		correctly, try reversing the direction or inverting the
-		switch positions.
-
-		a: The first digit of the I/O address.
-			Setting		Value
-			-------		-----
-			00		0
-			01		1
-			10		2
-			11		3
-
-		b: The second digit of the I/O address.
-			Setting		Value
-			-------		-----
-			0000		0
-			0001		1
-			0010		2
-			...		...
-			1110		E
-			1111		F
-
-		The I/O address is in the form ab0.  For example, if
-		a is 0x2 and b is 0xE, the address will be 0x2E0.
-
-		DO NOT SET THIS LESS THAN 0x200!!!!!
-
-
-		m: The first digit of the memory address.
-			Setting		Value
-			-------		-----
-			0000		0
-			0001		1
-			0010		2
-			...		...
-			1110		E
-			1111		F
-
-		The memory address is in the form m0000.  For example, if
-		m is D, the address will be 0xD0000.
-
-		DO NOT SET THIS TO C0000, F0000, OR LESS THAN A0000!
-
-                          1  2  3  4  5  6  7  8
-     S2                /--------------------------\
-(Station Address)      |  1  1  0  0  0  0  0  0  |
-                       \--------------------------/
-
-			Setting		Value
-			-------		-----
-			00000000	00
-			10000000	01
-			01000000	02
-			...
-			01111111	FE
-			11111111	FF
-
-		Note that this is binary with the digits reversed!
-
-		DO NOT SET THIS TO 0 OR 255 (0xFF)!
-
-
-*****************************************************************************
-
-** Standard Microsystems Corp (SMC) **
+
+::
+
+	     JP5		       [|]    :    :    :    :
+	(IRQ Setting)		      IRQ2  IRQ3 IRQ4 IRQ5 IRQ7
+			Put exactly one jumper on exactly one set of pins.
+
+
+				  1  2   3  4  5  6   7  8  9 10
+	     S1                /----------------------------------\
+	(I/O and Memory        |  1  1 * 0  0  0  0 * 1  1  0  1  |
+	 addresses)            \----------------------------------/
+				  |--|   |--------|   |--------|
+				  (a)       (b)           (m)
+
+			WARNING.  It's very important when setting these which way
+			you're holding the card, and which way you think is '1'!
+
+			If you suspect that your settings are not being made
+			correctly, try reversing the direction or inverting the
+			switch positions.
+
+			a: The first digit of the I/O address.
+				Setting		Value
+				-------		-----
+				00		0
+				01		1
+				10		2
+				11		3
+
+			b: The second digit of the I/O address.
+				Setting		Value
+				-------		-----
+				0000		0
+				0001		1
+				0010		2
+				...		...
+				1110		E
+				1111		F
+
+			The I/O address is in the form ab0.  For example, if
+			a is 0x2 and b is 0xE, the address will be 0x2E0.
+
+			DO NOT SET THIS LESS THAN 0x200!!!!!
+
+
+			m: The first digit of the memory address.
+				Setting		Value
+				-------		-----
+				0000		0
+				0001		1
+				0010		2
+				...		...
+				1110		E
+				1111		F
+
+			The memory address is in the form m0000.  For example, if
+			m is D, the address will be 0xD0000.
+
+			DO NOT SET THIS TO C0000, F0000, OR LESS THAN A0000!
+
+				  1  2  3  4  5  6  7  8
+	     S2                /--------------------------\
+	(Station Address)      |  1  1  0  0  0  0  0  0  |
+			       \--------------------------/
+
+				Setting		Value
+				-------		-----
+				00000000	00
+				10000000	01
+				01000000	02
+				...
+				01111111	FE
+				11111111	FF
+
+			Note that this is binary with the digits reversed!
+
+			DO NOT SET THIS TO 0 OR 255 (0xFF)!
+
+
 PC130E/PC270E (8-bit cards)
 ---------------------------
+
   - from Juergen Seifert <[email protected]>
 
-
-STANDARD MICROSYSTEMS CORPORATION (SMC) ARCNET(R)-PC130E/PC270E
-===============================================================
-
 This description has been written by Juergen Seifert <[email protected]>
-using information from the following Original SMC Manual 
+using information from the following Original SMC Manual
 
-             "Configuration Guide for
-             ARCNET(R)-PC130E/PC270
-            Network Controller Boards
-                Pub. # 900.044A
-                   June, 1989"
+	     "Configuration Guide for ARCNET(R)-PC130E/PC270 Network
+	     Controller Boards Pub. # 900.044A June, 1989"
 
 ARCNET is a registered trademark of the Datapoint Corporation
-SMC is a registered trademark of the Standard Microsystems Corporation  
+SMC is a registered trademark of the Standard Microsystems Corporation
 
-The PC130E is an enhanced version of the PC130 board, is equipped with a 
+The PC130E is an enhanced version of the PC130 board, is equipped with a
 standard BNC female connector for connection to RG-62/U coax cable.
 Since this board is designed both for point-to-point connection in star
-networks and for connection to bus networks, it is downwardly compatible 
+networks and for connection to bus networks, it is downwardly compatible
 with all the other standard boards designed for coax networks (that is,
-the PC120, PC110 and PC100 star topology boards and the PC220, PC210 and 
+the PC120, PC110 and PC100 star topology boards and the PC220, PC210 and
 PC200 bus topology boards).
 
-The PC270E is an enhanced version of the PC260 board, is equipped with two 
+The PC270E is an enhanced version of the PC260 board, is equipped with two
 modular RJ11-type jacks for connection to twisted pair wiring.
 It can be used in a star or a daisy-chained network.
 
+::
 
-         8 7 6 5 4 3 2 1
+	 8 7 6 5 4 3 2 1
     ________________________________________________________________
    |   |       S1        |                                          |
    |   |_________________|                                          |
@@ -587,27 +615,27 @@ It can be used in a star or a daisy-chained network.
        |                                             |
        |_____________________________________________|
 
-Legend:
+Legend::
 
-SMC 90C63	ARCNET Controller / Transceiver /Logic
-S1	1-3:	I/O Base Address Select
+  SMC 90C63	ARCNET Controller / Transceiver /Logic
+  S1	1-3:	I/O Base Address Select
 	4-6:	Memory Base Address Select
 	7-8:	RAM Offset Select
-S2	1-8:	Node ID Select
-EXT		Extended Timeout Select
-ROM		ROM Enable Select
-STAR		Selected - Star Topology	(PC130E only)
+  S2	1-8:	Node ID Select
+  EXT		Extended Timeout Select
+  ROM		ROM Enable Select
+  STAR		Selected - Star Topology	(PC130E only)
 		Deselected - Bus Topology	(PC130E only)
-CR3/CR4		Diagnostic LEDs
-J1		BNC RG62/U Connector		(PC130E only)
-J1		6-position Telephone Jack	(PC270E only)
-J2		6-position Telephone Jack	(PC270E only)
+  CR3/CR4	Diagnostic LEDs
+  J1		BNC RG62/U Connector		(PC130E only)
+  J1		6-position Telephone Jack	(PC270E only)
+  J2		6-position Telephone Jack	(PC270E only)
 
 Setting one of the switches to Off/Open means "1", On/Closed means "0".
 
 
 Setting the Node ID
--------------------
+^^^^^^^^^^^^^^^^^^^
 
 The eight switches in group S2 are used to set the node ID.
 These switches work in a way similar to the PC100-series cards; see that
@@ -615,10 +643,10 @@ entry for more information.
 
 
 Setting the I/O Base Address
-----------------------------
+^^^^^^^^^^^^^^^^^^^^^^^^^^^^
 
 The first three switches in switch group S1 are used to select one
-of eight possible I/O Base addresses using the following table
+of eight possible I/O Base addresses using the following table::
 
 
    Switch | Hex I/O
@@ -635,14 +663,16 @@ of eight possible I/O Base addresses using the following table
 
 
 Setting the Base Memory (RAM) buffer Address
---------------------------------------------
+^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^
 
 The memory buffer requires 2K of a 16K block of RAM. The base of this
 16K block can be located in any of eight positions.
 Switches 4-6 of switch group S1 select the Base of the 16K block.
-Within that 16K address space, the buffer may be assigned any one of four 
+Within that 16K address space, the buffer may be assigned any one of four
 positions, determined by the offset, switches 7 and 8 of group S1.
 
+::
+
    Switch     | Hex RAM | Hex ROM
    4 5 6  7 8 | Address | Address *)
    -----------|---------|-----------
@@ -650,115 +680,111 @@ positions, determined by the offset, switches 7 and 8 of group S1.
    0 0 0  0 1 |  C0800  |  C2000
    0 0 0  1 0 |  C1000  |  C2000
    0 0 0  1 1 |  C1800  |  C2000
-              |         |
+	      |         |
    0 0 1  0 0 |  C4000  |  C6000
    0 0 1  0 1 |  C4800  |  C6000
    0 0 1  1 0 |  C5000  |  C6000
    0 0 1  1 1 |  C5800  |  C6000
-              |         |
+	      |         |
    0 1 0  0 0 |  CC000  |  CE000
    0 1 0  0 1 |  CC800  |  CE000
    0 1 0  1 0 |  CD000  |  CE000
    0 1 0  1 1 |  CD800  |  CE000
-              |         |
+	      |         |
    0 1 1  0 0 |  D0000  |  D2000  (Manufacturer's default)
    0 1 1  0 1 |  D0800  |  D2000
    0 1 1  1 0 |  D1000  |  D2000
    0 1 1  1 1 |  D1800  |  D2000
-              |         |
+	      |         |
    1 0 0  0 0 |  D4000  |  D6000
    1 0 0  0 1 |  D4800  |  D6000
    1 0 0  1 0 |  D5000  |  D6000
    1 0 0  1 1 |  D5800  |  D6000
-              |         |
+	      |         |
    1 0 1  0 0 |  D8000  |  DA000
    1 0 1  0 1 |  D8800  |  DA000
    1 0 1  1 0 |  D9000  |  DA000
    1 0 1  1 1 |  D9800  |  DA000
-              |         |
+	      |         |
    1 1 0  0 0 |  DC000  |  DE000
    1 1 0  0 1 |  DC800  |  DE000
    1 1 0  1 0 |  DD000  |  DE000
    1 1 0  1 1 |  DD800  |  DE000
-              |         |
+	      |         |
    1 1 1  0 0 |  E0000  |  E2000
    1 1 1  0 1 |  E0800  |  E2000
    1 1 1  1 0 |  E1000  |  E2000
    1 1 1  1 1 |  E1800  |  E2000
-  
-*) To enable the 8K Boot PROM install the jumper ROM.
-   The default is jumper ROM not installed.
+
+  *) To enable the 8K Boot PROM install the jumper ROM.
+     The default is jumper ROM not installed.
 
 
 Setting the Timeouts and Interrupt
-----------------------------------
+^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^
 
-The jumpers labeled EXT1 and EXT2 are used to determine the timeout 
+The jumpers labeled EXT1 and EXT2 are used to determine the timeout
 parameters. These two jumpers are normally left open.
 
 To select a hardware interrupt level set one (only one!) of the jumpers
 IRQ2, IRQ3, IRQ4, IRQ5, IRQ7. The Manufacturer's default is IRQ2.
- 
+
 
 Configuring the PC130E for Star or Bus Topology
------------------------------------------------
+^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^
 
-The single jumper labeled STAR is used to configure the PC130E board for 
+The single jumper labeled STAR is used to configure the PC130E board for
 star or bus topology.
-When the jumper is installed, the board may be used in a star network, when 
+When the jumper is installed, the board may be used in a star network, when
 it is removed, the board can be used in a bus topology.
 
 
 Diagnostic LEDs
----------------
+^^^^^^^^^^^^^^^
 
 Two diagnostic LEDs are visible on the rear bracket of the board.
 The green LED monitors the network activity: the red one shows the
-board activity:
+board activity::
 
  Green  | Status               Red      | Status
  -------|-------------------   ---------|-------------------
   on    | normal activity      flash/on | data transfer
   blink | reconfiguration      off      | no data transfer;
   off   | defective board or            | incorrect memory or
-        | node ID is zero               | I/O address
+	| node ID is zero               | I/O address
 
 
-*****************************************************************************
-
-** Standard Microsystems Corp (SMC) **
 PC500/PC550 Longboard (16-bit cards)
--------------------------------------
+------------------------------------
+
   - from Juergen Seifert <[email protected]>
 
 
-STANDARD MICROSYSTEMS CORPORATION (SMC) ARCNET-PC500/PC550 Long Board
-=====================================================================
+  .. note::
 
-Note: There is another Version of the PC500 called Short Version, which 
+      There is another Version of the PC500 called Short Version, which
       is different in hard- and software! The most important differences
       are:
+
       - The long board has no Shared memory.
       - On the long board the selection of the interrupt is done by binary
-        coded switch, on the short board directly by jumper.
-        
+	coded switch, on the short board directly by jumper.
+
 [Avery's note: pay special attention to that: the long board HAS NO SHARED
-MEMORY.  This means the current Linux-ARCnet driver can't use these cards. 
+MEMORY.  This means the current Linux-ARCnet driver can't use these cards.
 I have obtained a PC500Longboard and will be doing some experiments on it in
 the future, but don't hold your breath.  Thanks again to Juergen Seifert for
 his advice about this!]
 
 This description has been written by Juergen Seifert <[email protected]>
-using information from the following Original SMC Manual 
+using information from the following Original SMC Manual
 
-             "Configuration Guide for
-             SMC ARCNET-PC500/PC550
-         Series Network Controller Boards
-             Pub. # 900.033 Rev. A
-                November, 1989"
+	 "Configuration Guide for SMC ARCNET-PC500/PC550
+	 Series Network Controller Boards Pub. # 900.033 Rev. A
+	 November, 1989"
 
 ARCNET is a registered trademark of the Datapoint Corporation
-SMC is a registered trademark of the Standard Microsystems Corporation  
+SMC is a registered trademark of the Standard Microsystems Corporation
 
 The PC500 is equipped with a standard BNC female connector for connection
 to RG-62/U coax cable.
@@ -769,7 +795,9 @@ The PC550 is equipped with two modular RJ11-type jacks for connection
 to twisted pair wiring.
 It can be used in a star or a daisy-chained (BUS) network.
 
-       1 
+::
+
+       1
        0 9 8 7 6 5 4 3 2 1     6 5 4 3 2 1
     ____________________________________________________________________
    < |         SW1         | |     SW2     |                            |
@@ -796,34 +824,34 @@ It can be used in a star or a daisy-chained (BUS) network.
    >    |  |                                             |
    <____|  |_____________________________________________|
 
-Legend:
+Legend::
 
-SW1	1-6:	I/O Base Address Select
+  SW1	1-6:	I/O Base Address Select
 	7-10:	Interrupt Select
-SW2	1-6:	Reserved for Future Use
-SW3	1-8:	Node ID Select
-JP2	1-4:	Extended Timeout Select
-JP6		Selected - Star Topology	(PC500 only)
+  SW2	1-6:	Reserved for Future Use
+  SW3	1-8:	Node ID Select
+  JP2	1-4:	Extended Timeout Select
+  JP6		Selected - Star Topology	(PC500 only)
 		Deselected - Bus Topology	(PC500 only)
-CR3	Green	Monitors Network Activity
-CR4	Red	Monitors Board Activity
-J1		BNC RG62/U Connector		(PC500 only)
-J1		6-position Telephone Jack	(PC550 only)
-J2		6-position Telephone Jack	(PC550 only)
+  CR3	Green	Monitors Network Activity
+  CR4	Red	Monitors Board Activity
+  J1		BNC RG62/U Connector		(PC500 only)
+  J1		6-position Telephone Jack	(PC550 only)
+  J2		6-position Telephone Jack	(PC550 only)
 
 Setting one of the switches to Off/Open means "1", On/Closed means "0".
 
 
 Setting the Node ID
--------------------
+^^^^^^^^^^^^^^^^^^^
 
 The eight switches in group SW3 are used to set the node ID. Each node
-attached to the network must have an unique node ID which must be 
+attached to the network must have an unique node ID which must be
 different from 0.
 Switch 1 serves as the least significant bit (LSB).
 
-The node ID is the sum of the values of all switches set to "1"  
-These values are:
+The node ID is the sum of the values of all switches set to "1"
+These values are::
 
     Switch | Value
     -------|-------
@@ -836,30 +864,30 @@ These values are:
       7    |  64
       8    | 128
 
-Some Examples:
+Some Examples::
 
-    Switch         | Hex     | Decimal 
+    Switch         | Hex     | Decimal
    8 7 6 5 4 3 2 1 | Node ID | Node ID
    ----------------|---------|---------
    0 0 0 0 0 0 0 0 |    not allowed
-   0 0 0 0 0 0 0 1 |    1    |    1 
+   0 0 0 0 0 0 0 1 |    1    |    1
    0 0 0 0 0 0 1 0 |    2    |    2
    0 0 0 0 0 0 1 1 |    3    |    3
        . . .       |         |
    0 1 0 1 0 1 0 1 |   55    |   85
        . . .       |         |
    1 0 1 0 1 0 1 0 |   AA    |  170
-       . . .       |         |  
+       . . .       |         |
    1 1 1 1 1 1 0 1 |   FD    |  253
    1 1 1 1 1 1 1 0 |   FE    |  254
-   1 1 1 1 1 1 1 1 |   FF    |  255 
+   1 1 1 1 1 1 1 1 |   FF    |  255
 
 
 Setting the I/O Base Address
-----------------------------
+^^^^^^^^^^^^^^^^^^^^^^^^^^^^
 
 The first six switches in switch group SW1 are used to select one
-of 32 possible I/O Base addresses using the following table
+of 32 possible I/O Base addresses using the following table::
 
    Switch       | Hex I/O
    6 5  4 3 2 1 | Address
@@ -899,16 +927,18 @@ of 32 possible I/O Base addresses using the following table
 
 
 Setting the Interrupt
----------------------
+^^^^^^^^^^^^^^^^^^^^^
 
-Switches seven through ten of switch group SW1 are used to select the 
-interrupt level. The interrupt level is binary coded, so selections 
+Switches seven through ten of switch group SW1 are used to select the
+interrupt level. The interrupt level is binary coded, so selections
 from 0 to 15 would be possible, but only the following eight values will
 be supported: 3, 4, 5, 7, 9, 10, 11, 12.
 
+::
+
    Switch   | IRQ
-   10 9 8 7 | 
-   ---------|-------- 
+   10 9 8 7 |
+   ---------|--------
     0 0 1 1 |  3
     0 1 0 0 |  4
     0 1 0 1 |  5
@@ -919,52 +949,50 @@ be supported: 3, 4, 5, 7, 9, 10, 11, 12.
     1 1 0 0 | 12
 
 
-Setting the Timeouts 
---------------------
+Setting the Timeouts
+^^^^^^^^^^^^^^^^^^^^
 
-The two jumpers JP2 (1-4) are used to determine the timeout parameters. 
+The two jumpers JP2 (1-4) are used to determine the timeout parameters.
 These two jumpers are normally left open.
 Refer to the COM9026 Data Sheet for alternate configurations.
 
 
 Configuring the PC500 for Star or Bus Topology
-----------------------------------------------
+^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^
 
-The single jumper labeled JP6 is used to configure the PC500 board for 
+The single jumper labeled JP6 is used to configure the PC500 board for
 star or bus topology.
-When the jumper is installed, the board may be used in a star network, when 
+When the jumper is installed, the board may be used in a star network, when
 it is removed, the board can be used in a bus topology.
 
 
 Diagnostic LEDs
----------------
+^^^^^^^^^^^^^^^
 
 Two diagnostic LEDs are visible on the rear bracket of the board.
 The green LED monitors the network activity: the red one shows the
-board activity:
+board activity::
 
  Green  | Status               Red      | Status
  -------|-------------------   ---------|-------------------
   on    | normal activity      flash/on | data transfer
   blink | reconfiguration      off      | no data transfer;
   off   | defective board or            | incorrect memory or
-        | node ID is zero               | I/O address
+	| node ID is zero               | I/O address
 
 
-*****************************************************************************
-
-** SMC **
 PC710 (8-bit card)
 ------------------
+
   - from J.S. van Oosten <[email protected]>
-  
+
 Note: this data is gathered by experimenting and looking at info of other
 cards. However, I'm sure I got 99% of the settings right.
 
 The SMC710 card resembles the PC270 card, but is much more basic (i.e. no
-LEDs, RJ11 jacks, etc.) and 8 bit. Here's a little drawing:
+LEDs, RJ11 jacks, etc.) and 8 bit. Here's a little drawing::
 
-    _______________________________________   
+    _______________________________________
    | +---------+  +---------+              |____
    | |   S2    |  |   S1    |              |
    | +---------+  +---------+              |
@@ -976,12 +1004,12 @@ LEDs, RJ11 jacks, etc.) and 8 bit. Here's a little drawing:
    |  +===+                                |
    |                                       |
    |   .. JP1   +----------+               |
-   |   ..       | big chip |               |   
+   |   ..       | big chip |               |
    |   ..       |  90C63   |               |
    |   ..       |          |               |
    |   ..       +----------+               |
     -------                     -----------
-           |||||||||||||||||||||
+	   |||||||||||||||||||||
 
 The row of jumpers at JP1 actually consists of 8 jumpers, (sometimes
 labelled) the same as on the PC270, from top to bottom: EXT2, EXT1, ROM,
@@ -992,71 +1020,76 @@ are swapped (S1 is the nodeaddress, S2 sets IO- and RAM-address).
 
 I know it works when connected to a PC110 type ARCnet board.
 
-	
+
 *****************************************************************************
 
-** Possibly SMC **
+Possibly SMC
+============
+
 LCS-8830(-T) (8 and 16-bit cards)
 ---------------------------------
+
   - from Mathias Katzer <[email protected]>
   - Marek Michalkiewicz <[email protected]> says the
     LCS-8830 is slightly different from LCS-8830-T.  These are 8 bit, BUS
     only (the JP0 jumper is hardwired), and BNC only.
-	
+
 This is a LCS-8830-T made by SMC, I think ('SMC' only appears on one PLCC,
 nowhere else, not even on the few Xeroxed sheets from the manual).
 
-SMC ARCnet Board Type LCS-8830-T
-
-   ------------------------------------
-  |                                    |
-  |              JP3 88  8 JP2         |
-  |       #####      | \               |
-  |       #####    ET1 ET2          ###|
-  |                              8  ###|
-  |  U3   SW 1                  JP0 ###|  Phone Jacks
-  |  --                             ###|
-  | |  |                               |
-  | |  |   SW2                         |
-  | |  |                               |
-  | |  |  #####                        |
-  |  --   #####                       ####  BNC Connector 
-  |                                   ####
-  |   888888 JP1                       |
-  |   234567                           |
-   --                           -------
-     |||||||||||||||||||||||||||
-      --------------------------
-
-
-SW1: DIP-Switches for Station Address
-SW2: DIP-Switches for Memory Base and I/O Base addresses
-
-JP0: If closed, internal termination on (default open)
-JP1: IRQ Jumpers
-JP2: Boot-ROM enabled if closed
-JP3: Jumpers for response timeout
- 
-U3: Boot-ROM Socket          
-
-
-ET1 ET2     Response Time     Idle Time    Reconfiguration Time
-
-               78                86               840
- X            285               316              1680
-     X        563               624              1680
- X   X       1130              1237              1680
-
-(X means closed jumper)
-
-(DIP-Switch downwards means "0")
+SMC ARCnet Board Type LCS-8830-T::
+
+     ------------------------------------
+    |                                    |
+    |              JP3 88  8 JP2         |
+    |       #####      | \               |
+    |       #####    ET1 ET2          ###|
+    |                              8  ###|
+    |  U3   SW 1                  JP0 ###|  Phone Jacks
+    |  --                             ###|
+    | |  |                               |
+    | |  |   SW2                         |
+    | |  |                               |
+    | |  |  #####                        |
+    |  --   #####                       ####  BNC Connector
+    |                                   ####
+    |   888888 JP1                       |
+    |   234567                           |
+     --                           -------
+       |||||||||||||||||||||||||||
+	--------------------------
+
+
+  SW1: DIP-Switches for Station Address
+  SW2: DIP-Switches for Memory Base and I/O Base addresses
+
+  JP0: If closed, internal termination on (default open)
+  JP1: IRQ Jumpers
+  JP2: Boot-ROM enabled if closed
+  JP3: Jumpers for response timeout
+
+  U3: Boot-ROM Socket
+
+
+  ET1 ET2     Response Time     Idle Time    Reconfiguration Time
+
+		 78                86               840
+   X            285               316              1680
+       X        563               624              1680
+   X   X       1130              1237              1680
+
+  (X means closed jumper)
+
+  (DIP-Switch downwards means "0")
 
 The station address is binary-coded with SW1.
 
 The I/O base address is coded with DIP-Switches 6,7 and 8 of SW2:
 
+========	========
 Switches        Base
 678             Address
+========	========
 000		260-26f
 100		290-29f
 010		2e0-2ef
@@ -1065,19 +1098,22 @@ Switches        Base
 101		350-35f
 011		380-38f
 111 		3e0-3ef
+========	========
 
 
 DIP Switches 1-5 of SW2 encode the RAM and ROM Address Range:
 
+========        ============= ================
 Switches        RAM           ROM
 12345           Address Range  Address Range
+========        ============= ================
 00000		C:0000-C:07ff	C:2000-C:3fff
 10000		C:0800-C:0fff
 01000		C:1000-C:17ff
 11000		C:1800-C:1fff
 00100		C:4000-C:47ff	C:6000-C:7fff
 10100		C:4800-C:4fff
-01100		C:5000-C:57ff 
+01100		C:5000-C:57ff
 11100		C:5800-C:5fff
 00010		C:C000-C:C7ff	C:E000-C:ffff
 10010		C:C800-C:Cfff
@@ -1094,7 +1130,7 @@ Switches        RAM           ROM
 00101		D:8000-D:87ff	D:A000-D:bfff
 10101		D:8800-D:8fff
 01101		D:9000-D:97ff
-11101		D:9800-D:9fff 
+11101		D:9800-D:9fff
 00011		D:C000-D:c7ff	D:E000-D:ffff
 10011		D:C800-D:cfff
 01011		D:D000-D:d7ff
@@ -1103,34 +1139,37 @@ Switches        RAM           ROM
 10111		E:0800-E:0fff
 01111		E:1000-E:17ff
 11111		E:1800-E:1fff
+========        ============= ================
 
 
-*****************************************************************************
+PureData Corp
+=============
 
-** PureData Corp **
 PDI507 (8-bit card)
 --------------------
+
   - from Mark Rejhon <[email protected]> (slight modifications by Avery)
   - Avery's note: I think PDI508 cards (but definitely NOT PDI508Plus cards)
     are mostly the same as this.  PDI508Plus cards appear to be mainly
     software-configured.
 
 Jumpers:
+
 	There is a jumper array at the bottom of the card, near the edge
-        connector.  This array is labelled J1.  They control the IRQs and
-        something else.  Put only one jumper on the IRQ pins.
+	connector.  This array is labelled J1.  They control the IRQs and
+	something else.  Put only one jumper on the IRQ pins.
 
 	ETS1, ETS2 are for timing on very long distance networks.  See the
 	more general information near the top of this file.
 
 	There is a J2 jumper on two pins.  A jumper should be put on them,
-        since it was already there when I got the card.  I don't know what
-        this jumper is for though.
+	since it was already there when I got the card.  I don't know what
+	this jumper is for though.
 
 	There is a two-jumper array for J3.  I don't know what it is for,
-        but there were already two jumpers on it when I got the card.  It's
-        a six pin grid in a two-by-three fashion.  The jumpers were
-        configured as follows:
+	but there were already two jumpers on it when I got the card.  It's
+	a six pin grid in a two-by-three fashion.  The jumpers were
+	configured as follows::
 
 	   .-------.
 	 o | o   o |
@@ -1140,28 +1179,28 @@ Jumpers:
 
 Carl de Billy <[email protected]> explains J3 and J4:
 
-	J3 Diagram:
+   J3 Diagram::
 
-           .-------.
-         o | o   o |
-           :-------:    TWIST Technology
-         o | o   o |
-           `-------'
-           .-------.
-           | o   o | o
-           :-------:    COAX Technology
-           | o   o | o
-           `-------'
+	   .-------.
+	 o | o   o |
+	   :-------:    TWIST Technology
+	 o | o   o |
+	   `-------'
+	   .-------.
+	   | o   o | o
+	   :-------:    COAX Technology
+	   | o   o | o
+	   `-------'
 
   - If using coax cable in a bus topology the J4 jumper must be removed;
     place it on one pin.
 
-  - If using bus topology with twisted pair wiring move the J3 
+  - If using bus topology with twisted pair wiring move the J3
     jumpers so they connect the middle pin and the pins closest to the RJ11
     Connectors.  Also the J4 jumper must be removed; place it on one pin of
     J4 jumper for storage.
 
-  - If using  star topology with twisted pair wiring move the J3 
+  - If using  star topology with twisted pair wiring move the J3
     jumpers so they connect the middle pin and the pins closest to the RJ11
     connectors.
 
@@ -1169,40 +1208,43 @@ Carl de Billy <[email protected]> explains J3 and J4:
 DIP Switches:
 
 	The DIP switches accessible on the accessible end of the card while
-        it is installed, is used to set the ARCnet address.  There are 8
-        switches.  Use an address from 1 to 254.
+	it is installed, is used to set the ARCnet address.  There are 8
+	switches.  Use an address from 1 to 254
 
-	Switch No.
-	12345678	ARCnet address
-	-----------------------------------------
+	==========      =========================
+	Switch No.	ARCnet address
+	12345678
+	==========      =========================
 	00000000	FF  	(Don't use this!)
 	00000001	FE
 	00000010	FD
-	....
-	11111101	2	
+	...
+	11111101	2
 	11111110	1
 	11111111	0	(Don't use this!)
+	==========      =========================
 
 	There is another array of eight DIP switches at the top of the
-        card.  There are five labelled MS0-MS4 which seem to control the
-        memory address, and another three labelled IO0-IO2 which seem to
-        control the base I/O address of the card.
+	card.  There are five labelled MS0-MS4 which seem to control the
+	memory address, and another three labelled IO0-IO2 which seem to
+	control the base I/O address of the card.
 
 	This was difficult to test by trial and error, and the I/O addresses
-        are in a weird order.  This was tested by setting the DIP switches,
-        rebooting the computer, and attempting to load ARCETHER at various
-        addresses (mostly between 0x200 and 0x400).  The address that caused
-        the red transmit LED to blink, is the one that I thought works.
+	are in a weird order.  This was tested by setting the DIP switches,
+	rebooting the computer, and attempting to load ARCETHER at various
+	addresses (mostly between 0x200 and 0x400).  The address that caused
+	the red transmit LED to blink, is the one that I thought works.
 
 	Also, the address 0x3D0 seem to have a special meaning, since the
-        ARCETHER packet driver loaded fine, but without the red LED
-        blinking.  I don't know what 0x3D0 is for though.  I recommend using
-        an address of 0x300 since Windows may not like addresses below
-        0x300.
+	ARCETHER packet driver loaded fine, but without the red LED
+	blinking.  I don't know what 0x3D0 is for though.  I recommend using
+	an address of 0x300 since Windows may not like addresses below
+	0x300.
 
-	IO Switch No.
-	210             I/O address
-	-------------------------------
+	=============   ===========
+	IO Switch No.   I/O address
+	210
+	=============   ===========
 	111             0x260
 	110             0x290
 	101             0x2E0
@@ -1211,29 +1253,31 @@ DIP Switches:
 	010             0x350
 	001             0x380
 	000             0x3E0
+	=============   ===========
 
 	The memory switches set a reserved address space of 0x1000 bytes
-        (0x100 segment units, or 4k).  For example if I set an address of
-        0xD000, it will use up addresses 0xD000 to 0xD100.
+	(0x100 segment units, or 4k).  For example if I set an address of
+	0xD000, it will use up addresses 0xD000 to 0xD100.
 
 	The memory switches were tested by booting using QEMM386 stealth,
-        and using LOADHI to see what address automatically became excluded
-        from the upper memory regions, and then attempting to load ARCETHER
-        using these addresses.
+	and using LOADHI to see what address automatically became excluded
+	from the upper memory regions, and then attempting to load ARCETHER
+	using these addresses.
 
 	I recommend using an ARCnet memory address of 0xD000, and putting
-        the EMS page frame at 0xC000 while using QEMM stealth mode.  That
-        way, you get contiguous high memory from 0xD100 almost all the way
-        the end of the megabyte.
+	the EMS page frame at 0xC000 while using QEMM stealth mode.  That
+	way, you get contiguous high memory from 0xD100 almost all the way
+	the end of the megabyte.
 
 	Memory Switch 0 (MS0) didn't seem to work properly when set to OFF
-        on my card.  It could be malfunctioning on my card.  Experiment with
-        it ON first, and if it doesn't work, set it to OFF.  (It may be a
-        modifier for the 0x200 bit?)
+	on my card.  It could be malfunctioning on my card.  Experiment with
+	it ON first, and if it doesn't work, set it to OFF.  (It may be a
+	modifier for the 0x200 bit?)
 
+	=============   ============================================
 	MS Switch No.
 	43210           Memory address
-	--------------------------------
+	=============   ============================================
 	00001           0xE100  (guessed - was not detected by QEMM)
 	00011           0xE000  (guessed - was not detected by QEMM)
 	00101           0xDD00
@@ -1250,40 +1294,36 @@ DIP Switches:
 	11011           0xC800 (guessed - crashes tested system)
 	11101           0xC500 (guessed - crashes tested system)
 	11111           0xC400 (guessed - crashes tested system)
-	
-	
-*****************************************************************************
+	=============   ============================================
+
+CNet Technology Inc.
+====================
 
-** CNet Technology Inc. **
 120 Series (8-bit cards)
 ------------------------
   - from Juergen Seifert <[email protected]>
 
-
-CNET TECHNOLOGY INC. (CNet) ARCNET 120A SERIES
-==============================================
-
 This description has been written by Juergen Seifert <[email protected]>
-using information from the following Original CNet Manual 
+using information from the following Original CNet Manual
 
-              "ARCNET
-            USER'S MANUAL 
-                for
-               CN120A
-               CN120AB
-               CN120TP
-               CN120ST
-               CN120SBT
-             P/N:12-01-0007
-             Revision 3.00"
+	      "ARCNET USER'S MANUAL for
+	      CN120A
+	      CN120AB
+	      CN120TP
+	      CN120ST
+	      CN120SBT
+	      P/N:12-01-0007
+	      Revision 3.00"
 
 ARCNET is a registered trademark of the Datapoint Corporation
 
-P/N 120A   ARCNET 8 bit XT/AT Star
-P/N 120AB  ARCNET 8 bit XT/AT Bus
-P/N 120TP  ARCNET 8 bit XT/AT Twisted Pair
-P/N 120ST  ARCNET 8 bit XT/AT Star, Twisted Pair
-P/N 120SBT ARCNET 8 bit XT/AT Star, Bus, Twisted Pair
+- P/N 120A   ARCNET 8 bit XT/AT Star
+- P/N 120AB  ARCNET 8 bit XT/AT Bus
+- P/N 120TP  ARCNET 8 bit XT/AT Twisted Pair
+- P/N 120ST  ARCNET 8 bit XT/AT Star, Twisted Pair
+- P/N 120SBT ARCNET 8 bit XT/AT Star, Bus, Twisted Pair
+
+::
 
     __________________________________________________________________
    |                                                                  |
@@ -1307,75 +1347,77 @@ P/N 120SBT ARCNET 8 bit XT/AT Star, Bus, Twisted Pair
    |  >  SOCKET      |  JP 6 5 4 3 2                    |o|o|o| | J1  |
    |  |______________|    |o|o|o|o|o|                   |o|o|o| |_____|
    |_____                 |o|o|o|o|o|                   ______________|
-         |                                             |
-         |_____________________________________________|
+	 |                                             |
+	 |_____________________________________________|
 
-Legend:
+Legend::
 
-90C65       ARCNET Probe
-S1  1-5:    Base Memory Address Select
-    6-8:    Base I/O Address Select
-S2  1-8:    Node ID Select (ID0-ID7)
-JP1     ROM Enable Select
-JP2     IRQ2
-JP3     IRQ3
-JP4     IRQ4
-JP5     IRQ5
-JP6     IRQ7
-JP7/JP8     ET1, ET2 Timeout Parameters
-JP10/JP11   Coax / Twisted Pair Select  (CN120ST/SBT only)
-JP12        Terminator Select       (CN120AB/ST/SBT only)
-J1      BNC RG62/U Connector        (all except CN120TP)
-J2      Two 6-position Telephone Jack   (CN120TP/ST/SBT only)
+  90C65       ARCNET Probe
+  S1  1-5:    Base Memory Address Select
+      6-8:    Base I/O Address Select
+  S2  1-8:    Node ID Select (ID0-ID7)
+  JP1     ROM Enable Select
+  JP2     IRQ2
+  JP3     IRQ3
+  JP4     IRQ4
+  JP5     IRQ5
+  JP6     IRQ7
+  JP7/JP8     ET1, ET2 Timeout Parameters
+  JP10/JP11   Coax / Twisted Pair Select  (CN120ST/SBT only)
+  JP12        Terminator Select       (CN120AB/ST/SBT only)
+  J1      BNC RG62/U Connector        (all except CN120TP)
+  J2      Two 6-position Telephone Jack   (CN120TP/ST/SBT only)
 
 Setting one of the switches to Off means "1", On means "0".
 
 
 Setting the Node ID
--------------------
+^^^^^^^^^^^^^^^^^^^
 
 The eight switches in SW2 are used to set the node ID. Each node attached
 to the network must have an unique node ID which must be different from 0.
 Switch 1 (ID0) serves as the least significant bit (LSB).
 
-The node ID is the sum of the values of all switches set to "1"  
+The node ID is the sum of the values of all switches set to "1"
 These values are:
 
-   Switch | Label | Value
-   -------|-------|-------
-     1    | ID0   |   1
-     2    | ID1   |   2
-     3    | ID2   |   4
-     4    | ID3   |   8
-     5    | ID4   |  16
-     6    | ID5   |  32
-     7    | ID6   |  64
-     8    | ID7   | 128
+   =======  ======  =====
+   Switch   Label   Value
+   =======  ======  =====
+     1      ID0       1
+     2      ID1       2
+     3      ID2       4
+     4      ID3       8
+     5      ID4      16
+     6      ID5      32
+     7      ID6      64
+     8      ID7     128
+   =======  ======  =====
 
-Some Examples:
+Some Examples::
 
-    Switch         | Hex     | Decimal 
+    Switch         | Hex     | Decimal
    8 7 6 5 4 3 2 1 | Node ID | Node ID
    ----------------|---------|---------
    0 0 0 0 0 0 0 0 |    not allowed
-   0 0 0 0 0 0 0 1 |    1    |    1 
+   0 0 0 0 0 0 0 1 |    1    |    1
    0 0 0 0 0 0 1 0 |    2    |    2
    0 0 0 0 0 0 1 1 |    3    |    3
        . . .       |         |
    0 1 0 1 0 1 0 1 |   55    |   85
        . . .       |         |
    1 0 1 0 1 0 1 0 |   AA    |  170
-       . . .       |         |  
+       . . .       |         |
    1 1 1 1 1 1 0 1 |   FD    |  253
    1 1 1 1 1 1 1 0 |   FE    |  254
    1 1 1 1 1 1 1 1 |   FF    |  255
 
 
 Setting the I/O Base Address
-----------------------------
+^^^^^^^^^^^^^^^^^^^^^^^^^^^^
 
 The last three switches in switch block SW1 are used to select one
-of eight possible I/O Base addresses using the following table
+of eight possible I/O Base addresses using the following table::
 
 
    Switch      | Hex I/O
@@ -1392,13 +1434,15 @@ of eight possible I/O Base addresses using the following table
 
 
 Setting the Base Memory (RAM) buffer Address
---------------------------------------------
+^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^
 
-The memory buffer (RAM) requires 2K. The base of this buffer can be 
+The memory buffer (RAM) requires 2K. The base of this buffer can be
 located in any of eight positions. The address of the Boot Prom is
 memory base + 8K or memory base + 0x2000.
 Switches 1-5 of switch block SW1 select the Memory Base address.
 
+::
+
    Switch              | Hex RAM | Hex ROM
     1   2   3   4   5  | Address | Address *)
    --------------------|---------|-----------
@@ -1410,22 +1454,24 @@ Switches 1-5 of switch block SW1 select the Memory Base address.
    ON  ON  OFF ON  OFF |  D8000  |  DA000
    ON  ON  ON  OFF OFF |  DC000  |  DE000
    ON  ON  OFF OFF OFF |  E0000  |  E2000
-  
-*) To enable the Boot ROM install the jumper JP1
 
-Note: Since the switches 1 and 2 are always set to ON it may be possible
+  *) To enable the Boot ROM install the jumper JP1
+
+.. note::
+
+      Since the switches 1 and 2 are always set to ON it may be possible
       that they can be used to add an offset of 2K, 4K or 6K to the base
       address, but this feature is not documented in the manual and I
       haven't tested it yet.
 
 
 Setting the Interrupt Line
---------------------------
+^^^^^^^^^^^^^^^^^^^^^^^^^^
 
 To select a hardware interrupt level install one (only one!) of the jumpers
-JP2, JP3, JP4, JP5, JP6. JP2 is the default.
+JP2, JP3, JP4, JP5, JP6. JP2 is the default::
 
-   Jumper | IRQ     
+   Jumper | IRQ
    -------|-----
      2    |  2
      3    |  3
@@ -1435,71 +1481,66 @@ JP2, JP3, JP4, JP5, JP6. JP2 is the default.
 
 
 Setting the Internal Terminator on CN120AB/TP/SBT
---------------------------------------------------
+^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^
 
-The jumper JP12 is used to enable the internal terminator. 
+The jumper JP12 is used to enable the internal terminator::
 
-                         -----
-       0                |  0  |     
+			 -----
+       0                |  0  |
      -----   ON         |     |  ON
     |  0  |             |  0  |
     |     |  OFF         -----   OFF
     |  0  |                0
      -----
-   Terminator          Terminator 
+   Terminator          Terminator
     disabled            enabled
-  
+
 
 Selecting the Connector Type on CN120ST/SBT
--------------------------------------------
+^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^
+
+::
 
      JP10    JP11        JP10    JP11
-                         -----   -----
-       0       0        |  0  | |  0  |       
+			 -----   -----
+       0       0        |  0  | |  0  |
      -----   -----      |     | |     |
     |  0  | |  0  |     |  0  | |  0  |
     |     | |     |      -----   -----
-    |  0  | |  0  |        0       0 
+    |  0  | |  0  |        0       0
      -----   -----
-     Coaxial Cable       Twisted Pair Cable 
+     Coaxial Cable       Twisted Pair Cable
        (Default)
 
 
 Setting the Timeout Parameters
-------------------------------
+^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^
 
-The jumpers labeled EXT1 and EXT2 are used to determine the timeout 
+The jumpers labeled EXT1 and EXT2 are used to determine the timeout
 parameters. These two jumpers are normally left open.
 
 
+CNet Technology Inc.
+====================
 
-*****************************************************************************
-
-** CNet Technology Inc. **
 160 Series (16-bit cards)
 -------------------------
   - from Juergen Seifert <[email protected]>
 
-CNET TECHNOLOGY INC. (CNet) ARCNET 160A SERIES
-==============================================
-
 This description has been written by Juergen Seifert <[email protected]>
-using information from the following Original CNet Manual 
+using information from the following Original CNet Manual
 
-              "ARCNET
-            USER'S MANUAL 
-                for
-               CN160A
-               CN160AB
-               CN160TP
-             P/N:12-01-0006
-             Revision 3.00"
+	      "ARCNET USER'S MANUAL for
+	      CN160A CN160AB CN160TP
+	      P/N:12-01-0006 Revision 3.00"
 
 ARCNET is a registered trademark of the Datapoint Corporation
 
-P/N 160A   ARCNET 16 bit XT/AT Star
-P/N 160AB  ARCNET 16 bit XT/AT Bus
-P/N 160TP  ARCNET 16 bit XT/AT Twisted Pair
+- P/N 160A   ARCNET 16 bit XT/AT Star
+- P/N 160AB  ARCNET 16 bit XT/AT Bus
+- P/N 160TP  ARCNET 16 bit XT/AT Twisted Pair
+
+::
 
    ___________________________________________________________________
   <                             _________________________          ___|
@@ -1526,30 +1567,30 @@ P/N 160TP  ARCNET 16 bit XT/AT Twisted Pair
   >            |  |                                       |
   <____________|  |_______________________________________|
 
-Legend:
+Legend::
 
-9026            ARCNET Probe
-SW1 1-6:    Base I/O Address Select
-    7-10:   Base Memory Address Select
-SW2 1-8:    Node ID Select (ID0-ID7)
-JP1/JP2     ET1, ET2 Timeout Parameters
-JP3-JP13    Interrupt Select
-J1      BNC RG62/U Connector        (CN160A/AB only)
-J1      Two 6-position Telephone Jack   (CN160TP only)
-LED
+  9026            ARCNET Probe
+  SW1 1-6:    Base I/O Address Select
+      7-10:   Base Memory Address Select
+  SW2 1-8:    Node ID Select (ID0-ID7)
+  JP1/JP2     ET1, ET2 Timeout Parameters
+  JP3-JP13    Interrupt Select
+  J1      BNC RG62/U Connector        (CN160A/AB only)
+  J1      Two 6-position Telephone Jack   (CN160TP only)
+  LED
 
 Setting one of the switches to Off means "1", On means "0".
 
 
 Setting the Node ID
--------------------
+^^^^^^^^^^^^^^^^^^^
 
 The eight switches in SW2 are used to set the node ID. Each node attached
 to the network must have an unique node ID which must be different from 0.
 Switch 1 (ID0) serves as the least significant bit (LSB).
 
-The node ID is the sum of the values of all switches set to "1"  
-These values are:
+The node ID is the sum of the values of all switches set to "1"
+These values are::
 
    Switch | Label | Value
    -------|-------|-------
@@ -1562,32 +1603,32 @@ These values are:
      7    | ID6   |  64
      8    | ID7   | 128
 
-Some Examples:
+Some Examples::
 
-    Switch         | Hex     | Decimal 
+    Switch         | Hex     | Decimal
    8 7 6 5 4 3 2 1 | Node ID | Node ID
    ----------------|---------|---------
    0 0 0 0 0 0 0 0 |    not allowed
-   0 0 0 0 0 0 0 1 |    1    |    1 
+   0 0 0 0 0 0 0 1 |    1    |    1
    0 0 0 0 0 0 1 0 |    2    |    2
    0 0 0 0 0 0 1 1 |    3    |    3
        . . .       |         |
    0 1 0 1 0 1 0 1 |   55    |   85
        . . .       |         |
    1 0 1 0 1 0 1 0 |   AA    |  170
-       . . .       |         |  
+       . . .       |         |
    1 1 1 1 1 1 0 1 |   FD    |  253
    1 1 1 1 1 1 1 0 |   FE    |  254
    1 1 1 1 1 1 1 1 |   FF    |  255
 
 
 Setting the I/O Base Address
-----------------------------
+^^^^^^^^^^^^^^^^^^^^^^^^^^^^
 
 The first six switches in switch block SW1 are used to select the I/O Base
-address using the following table:
+address using the following table::
 
-             Switch        | Hex I/O
+	     Switch        | Hex I/O
     1   2   3   4   5   6  | Address
    ------------------------|--------
    OFF ON  ON  OFF OFF ON  |  260
@@ -1604,10 +1645,10 @@ Note: Other IO-Base addresses seem to be selectable, but only the above
 
 
 Setting the Base Memory (RAM) buffer Address
---------------------------------------------
+^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^
 
 The switches 7-10 of switch block SW1 are used to select the Memory
-Base address of the RAM (2K) and the PROM.
+Base address of the RAM (2K) and the PROM::
 
    Switch          | Hex RAM | Hex ROM
     7   8   9  10  | Address | Address
@@ -1616,17 +1657,19 @@ Base address of the RAM (2K) and the PROM.
    OFF OFF ON  OFF |  D0000  |  D8000 (Default)
    OFF OFF OFF ON  |  E0000  |  E8000
 
-Note: Other MEM-Base addresses seem to be selectable, but only the above
+.. note::
+
+      Other MEM-Base addresses seem to be selectable, but only the above
       combinations are documented.
 
 
 Setting the Interrupt Line
---------------------------
+^^^^^^^^^^^^^^^^^^^^^^^^^^
 
 To select a hardware interrupt level install one (only one!) of the jumpers
-JP3 through JP13 using the following table:
+JP3 through JP13 using the following table::
 
-   Jumper | IRQ     
+   Jumper | IRQ
    -------|-----------------
      3    |  14
      4    |  15
@@ -1640,10 +1683,12 @@ JP3 through JP13 using the following table:
     12    |   7
     13    |   2 (=9) Default!
 
-Note:  - Do not use JP11=IRQ6, it may conflict with your Floppy Disk
-         Controller
+.. note::
+
+       - Do not use JP11=IRQ6, it may conflict with your Floppy Disk
+	 Controller
        - Use JP3=IRQ14 only, if you don't have an IDE-, MFM-, or RLL-
-         Hard Disk, it may conflict with their controllers
+	 Hard Disk, it may conflict with their controllers
 
 
 Setting the Timeout Parameters
@@ -1653,14 +1698,16 @@ The jumpers labeled JP1 and JP2 are used to determine the timeout
 parameters. These two jumpers are normally left open.
 
 
-*****************************************************************************
+Lantech
+=======
 
-** Lantech **
 8-bit card, unknown model
 -------------------------
   - from Vlad Lungu <[email protected]> - his e-mail address seemed broken at
     the time I tried to reach him.  Sorry Vlad, if you didn't get my reply.
 
+::
+
    ________________________________________________________________
    |   1         8                                                 |
    |   ___________                                               __|
@@ -1683,25 +1730,27 @@ parameters. These two jumpers are normally left open.
    |      |    PROM    |        |ooooo|  JP6                       |
    |      |____________|        |ooooo|                            |
    |_____________                                             _   _|
-                |____________________________________________| |__|
+		|____________________________________________| |__|
 
 
 UM9065L : ARCnet Controller
 
 SW 1    : Shared Memory Address and I/O Base
 
-        ON=0
+::
 
-        12345|Memory Address
-        -----|--------------
-        00001|  D4000
-        00010|  CC000
-        00110|  D0000
-        01110|  D1000
-        01101|  D9000
-        10010|  CC800
-        10011|  DC800
-        11110|  D1800
+	ON=0
+
+	12345|Memory Address
+	-----|--------------
+	00001|  D4000
+	00010|  CC000
+	00110|  D0000
+	01110|  D1000
+	01101|  D9000
+	10010|  CC800
+	10011|  DC800
+	11110|  D1800
 
 It seems that the bits are considered in reverse order.  Also, you must
 observe that some of those addresses are unusual and I didn't probe them; I
@@ -1710,43 +1759,48 @@ some others that I didn't write here the card seems to conflict with the
 video card (an S3 GENDAC). I leave the full decoding of those addresses to
 you.
 
-        678| I/O Address
-        ---|------------
-        000|    260
-        001|    failed probe
-        010|    2E0
-        011|    380
-        100|    290
-        101|    350
-        110|    failed probe
-        111|    3E0
+::
 
-SW 2  : Node ID (binary coded)
+	678| I/O Address
+	---|------------
+	000|    260
+	001|    failed probe
+	010|    2E0
+	011|    380
+	100|    290
+	101|    350
+	110|    failed probe
+	111|    3E0
 
-JP 4  : Boot PROM enable   CLOSE - enabled
-                           OPEN  - disabled
+  SW 2  : Node ID (binary coded)
 
-JP 6  : IRQ set (ONLY ONE jumper on 1-5 for IRQ 2-6)
+  JP 4  : Boot PROM enable   CLOSE - enabled
+			     OPEN  - disabled
 
+  JP 6  : IRQ set (ONLY ONE jumper on 1-5 for IRQ 2-6)
 
-*****************************************************************************
 
-** Acer **
+Acer
+====
+
 8-bit card, Model 5210-003
 --------------------------
+
   - from Vojtech Pavlik <[email protected]> using portions of the existing
     arcnet-hardware file.
 
 This is a 90C26 based card.  Its configuration seems similar to the SMC
 PC100, but has some additional jumpers I don't know the meaning of.
 
-               __
-              |  |
+::
+
+	       __
+	      |  |
    ___________|__|_________________________
   |         |      |                       |
   |         | BNC  |                       |
   |         |______|                    ___|
-  |  _____________________             |___  
+  |  _____________________             |___
   | |                     |                |
   | | Hybrid IC           |                |
   | |                     |       o|o J1   |
@@ -1762,51 +1816,51 @@ PC100, but has some additional jumpers I don't know the meaning of.
   |                    _____               |
   |                   |     |   _____      |
   |                   |     |  |     |  ___|
-  |                   |     |  |     | |    
-  |  _____            | ROM |  | UFS | |    
-  | |     |           |     |  |     | |   
-  | |     |     ___   |     |  |     | |   
-  | |     |    |   |  |__.__|  |__.__| |   
-  | | NCR |    |XTL|   _____    _____  |   
-  | |     |    |___|  |     |  |     | |   
-  | |90C26|           |     |  |     | |   
-  | |     |           | RAM |  | UFS | |   
-  | |     | J17 o|o   |     |  |     | |   
-  | |     | J16 o|o   |     |  |     | |   
-  | |__.__|           |__.__|  |__.__| |   
-  |  ___                               |   
-  | |   |8                             |   
-  | |SW2|                              |   
-  | |   |                              |   
-  | |___|1                             |   
-  |  ___                               |   
-  | |   |10           J18 o|o          |   
-  | |   |                 o|o          |   
-  | |SW1|                 o|o          |   
-  | |   |             J21 o|o          |   
-  | |___|1                             |   
-  |                                    |   
-  |____________________________________|   
+  |                   |     |  |     | |
+  |  _____            | ROM |  | UFS | |
+  | |     |           |     |  |     | |
+  | |     |     ___   |     |  |     | |
+  | |     |    |   |  |__.__|  |__.__| |
+  | | NCR |    |XTL|   _____    _____  |
+  | |     |    |___|  |     |  |     | |
+  | |90C26|           |     |  |     | |
+  | |     |           | RAM |  | UFS | |
+  | |     | J17 o|o   |     |  |     | |
+  | |     | J16 o|o   |     |  |     | |
+  | |__.__|           |__.__|  |__.__| |
+  |  ___                               |
+  | |   |8                             |
+  | |SW2|                              |
+  | |   |                              |
+  | |___|1                             |
+  |  ___                               |
+  | |   |10           J18 o|o          |
+  | |   |                 o|o          |
+  | |SW1|                 o|o          |
+  | |   |             J21 o|o          |
+  | |___|1                             |
+  |                                    |
+  |____________________________________|
 
 
-Legend:
+Legend::
 
-90C26       ARCNET Chip
-XTL         20 MHz Crystal
-SW1 1-6     Base I/O Address Select
-    7-10    Memory Address Select
-SW2 1-8     Node ID Select (ID0-ID7)
-J1-J5       IRQ Select
-J6-J21      Unknown (Probably extra timeouts & ROM enable ...)
-LED1        Activity LED 
-BNC         Coax connector (STAR ARCnet)
-RAM         2k of SRAM
-ROM         Boot ROM socket
-UFS         Unidentified Flying Sockets
+  90C26       ARCNET Chip
+  XTL         20 MHz Crystal
+  SW1 1-6     Base I/O Address Select
+      7-10    Memory Address Select
+  SW2 1-8     Node ID Select (ID0-ID7)
+  J1-J5       IRQ Select
+  J6-J21      Unknown (Probably extra timeouts & ROM enable ...)
+  LED1        Activity LED
+  BNC         Coax connector (STAR ARCnet)
+  RAM         2k of SRAM
+  ROM         Boot ROM socket
+  UFS         Unidentified Flying Sockets
 
 
 Setting the Node ID
--------------------
+^^^^^^^^^^^^^^^^^^^
 
 The eight switches in SW2 are used to set the node ID. Each node attached
 to the network must have an unique node ID which must not be 0.
@@ -1815,7 +1869,7 @@ Switch 1 (ID0) serves as the least significant bit (LSB).
 Setting one of the switches to OFF means "1", ON means "0".
 
 The node ID is the sum of the values of all switches set to "1"
-These values are:
+These values are::
 
    Switch | Value
    -------|-------
@@ -1832,40 +1886,40 @@ Don't set this to 0 or 255; these values are reserved.
 
 
 Setting the I/O Base Address
-----------------------------
+^^^^^^^^^^^^^^^^^^^^^^^^^^^^
 
 The switches 1 to 6 of switch block SW1 are used to select one
-of 32 possible I/O Base addresses using the following tables
-   
-          | Hex
+of 32 possible I/O Base addresses using the following tables::
+
+	  | Hex
    Switch | Value
    -------|-------
-     1    | 200  
-     2    | 100  
-     3    |  80  
-     4    |  40  
-     5    |  20  
-     6    |  10 
+     1    | 200
+     2    | 100
+     3    |  80
+     4    |  40
+     5    |  20
+     6    |  10
 
 The I/O address is sum of all switches set to "1". Remember that
 the I/O address space bellow 0x200 is RESERVED for mainboard, so
-switch 1 should be ALWAYS SET TO OFF. 
+switch 1 should be ALWAYS SET TO OFF.
 
 
 Setting the Base Memory (RAM) buffer Address
---------------------------------------------
+^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^
 
 The memory buffer (RAM) requires 2K. The base of this buffer can be
 located in any of sixteen positions. However, the addresses below
 A0000 are likely to cause system hang because there's main RAM.
 
-Jumpers 7-10 of switch block SW1 select the Memory Base address.
+Jumpers 7-10 of switch block SW1 select the Memory Base address::
 
    Switch          | Hex RAM
     7   8   9  10  | Address
    ----------------|---------
    OFF OFF OFF OFF |  F0000 (conflicts with main BIOS)
-   OFF OFF OFF ON  |  E0000 
+   OFF OFF OFF ON  |  E0000
    OFF OFF ON  OFF |  D0000
    OFF OFF ON  ON  |  C0000 (conflicts with video BIOS)
    OFF ON  OFF OFF |  B0000 (conflicts with mono video)
@@ -1873,10 +1927,10 @@ Jumpers 7-10 of switch block SW1 select the Memory Base address.
 
 
 Setting the Interrupt Line
---------------------------
+^^^^^^^^^^^^^^^^^^^^^^^^^^
 
-Jumpers 1-5 of the jumper block J1 control the IRQ level. ON means 
-shorted, OFF means open.
+Jumpers 1-5 of the jumper block J1 control the IRQ level. ON means
+shorted, OFF means open::
 
     Jumper              |  IRQ
     1   2   3   4   5   |
@@ -1889,65 +1943,67 @@ shorted, OFF means open.
 
 
 Unknown jumpers & sockets
--------------------------
+^^^^^^^^^^^^^^^^^^^^^^^^^
 
 I know nothing about these. I just guess that J16&J17 are timeout
 jumpers and maybe one of J18-J21 selects ROM. Also J6-J10 and
 J11-J15 are connecting IRQ2-7 to some pins on the UFSs. I can't
 guess the purpose.
 
+Datapoint?
+==========
 
-*****************************************************************************
-
-** Datapoint? **
 LAN-ARC-8, an 8-bit card
 ------------------------
+
   - from Vojtech Pavlik <[email protected]>
 
 This is another SMC 90C65-based ARCnet card. I couldn't identify the
 manufacturer, but it might be DataPoint, because the card has the
 original arcNet logo in its upper right corner.
 
-          _______________________________________________________
-         |                         _________                     |
-         |                        |   SW2   | ON      arcNet     |
-         |                        |_________| OFF             ___|
-         |  _____________         1 ______  8                |   | 8  
-         | |             | SW1     | XTAL | ____________     | S |    
-         | > RAM (2k)    |         |______||            |    | W |    
-         | |_____________|                 |      H     |    | 3 |    
-         |                        _________|_____ y     |    |___| 1  
-         |  _________            |         |     |b     |        |    
-         | |_________|           |         |     |r     |        |    
-         |                       |     SMC |     |i     |        |    
-         |                       |    90C65|     |d     |        |      
-         |  _________            |         |     |      |        |
-         | |   SW1   | ON        |         |     |I     |        |
-         | |_________| OFF       |_________|_____/C     |   _____|
-         |  1       8                      |            |  |     |___
-         |  ______________                 |            |  | BNC |___|
-         | |              |                |____________|  |_____|
-         | > EPROM SOCKET |              _____________           |
-         | |______________|             |_____________|          |
-         |                                         ______________|
-         |                                        | 
-         |________________________________________|
+::
 
-Legend:
+	  _______________________________________________________
+	 |                         _________                     |
+	 |                        |   SW2   | ON      arcNet     |
+	 |                        |_________| OFF             ___|
+	 |  _____________         1 ______  8                |   | 8
+	 | |             | SW1     | XTAL | ____________     | S |
+	 | > RAM (2k)    |         |______||            |    | W |
+	 | |_____________|                 |      H     |    | 3 |
+	 |                        _________|_____ y     |    |___| 1
+	 |  _________            |         |     |b     |        |
+	 | |_________|           |         |     |r     |        |
+	 |                       |     SMC |     |i     |        |
+	 |                       |    90C65|     |d     |        |
+	 |  _________            |         |     |      |        |
+	 | |   SW1   | ON        |         |     |I     |        |
+	 | |_________| OFF       |_________|_____/C     |   _____|
+	 |  1       8                      |            |  |     |___
+	 |  ______________                 |            |  | BNC |___|
+	 | |              |                |____________|  |_____|
+	 | > EPROM SOCKET |              _____________           |
+	 | |______________|             |_____________|          |
+	 |                                         ______________|
+	 |                                        |
+	 |________________________________________|
 
-90C65       ARCNET Chip 
-SW1 1-5:    Base Memory Address Select
-    6-8:    Base I/O Address Select
-SW2 1-8:    Node ID Select
-SW3 1-5:    IRQ Select   
-    6-7:    Extra Timeout
-    8  :    ROM Enable   
-BNC         Coax connector
-XTAL        20 MHz Crystal
+Legend::
+
+  90C65       ARCNET Chip
+  SW1 1-5:    Base Memory Address Select
+      6-8:    Base I/O Address Select
+  SW2 1-8:    Node ID Select
+  SW3 1-5:    IRQ Select
+      6-7:    Extra Timeout
+      8  :    ROM Enable
+  BNC         Coax connector
+  XTAL        20 MHz Crystal
 
 
 Setting the Node ID
--------------------
+^^^^^^^^^^^^^^^^^^^
 
 The eight switches in SW3 are used to set the node ID. Each node attached
 to the network must have an unique node ID which must not be 0.
@@ -1955,8 +2011,8 @@ Switch 1 serves as the least significant bit (LSB).
 
 Setting one of the switches to Off means "1", On means "0".
 
-The node ID is the sum of the values of all switches set to "1"  
-These values are:
+The node ID is the sum of the values of all switches set to "1"
+These values are::
 
    Switch | Value
    -------|-------
@@ -1971,10 +2027,10 @@ These values are:
 
 
 Setting the I/O Base Address
-----------------------------
+^^^^^^^^^^^^^^^^^^^^^^^^^^^^
 
 The last three switches in switch block SW1 are used to select one
-of eight possible I/O Base addresses using the following table
+of eight possible I/O Base addresses using the following table::
 
 
    Switch      | Hex I/O
@@ -1991,13 +2047,16 @@ of eight possible I/O Base addresses using the following table
 
 
 Setting the Base Memory (RAM) buffer Address
---------------------------------------------
+^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^
 
-The memory buffer (RAM) requires 2K. The base of this buffer can be 
+The memory buffer (RAM) requires 2K. The base of this buffer can be
 located in any of eight positions. The address of the Boot Prom is
 memory base + 0x2000.
+
 Jumpers 3-5 of switch block SW1 select the Memory Base address.
 
+::
+
    Switch              | Hex RAM | Hex ROM
     1   2   3   4   5  | Address | Address *)
    --------------------|---------|-----------
@@ -2009,16 +2068,16 @@ Jumpers 3-5 of switch block SW1 select the Memory Base address.
    ON  ON  OFF ON  OFF |  D8000  |  DA000
    ON  ON  ON  OFF OFF |  DC000  |  DE000
    ON  ON  OFF OFF OFF |  E0000  |  E2000
-  
-*) To enable the Boot ROM set the switch 8 of switch block SW3 to position ON.
+
+  *) To enable the Boot ROM set the switch 8 of switch block SW3 to position ON.
 
 The switches 1 and 2 probably add 0x0800 and 0x1000 to RAM base address.
 
 
 Setting the Interrupt Line
---------------------------
+^^^^^^^^^^^^^^^^^^^^^^^^^^
 
-Switches 1-5 of the switch block SW3 control the IRQ level.
+Switches 1-5 of the switch block SW3 control the IRQ level::
 
     Jumper              |  IRQ
     1   2   3   4   5   |
@@ -2031,64 +2090,67 @@ Switches 1-5 of the switch block SW3 control the IRQ level.
 
 
 Setting the Timeout Parameters
-------------------------------
+^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^
 
 The switches 6-7 of the switch block SW3 are used to determine the timeout
 parameters.  These two switches are normally left in the OFF position.
 
 
-*****************************************************************************
+Topware
+=======
 
-** Topware **
 8-bit card, TA-ARC/10
--------------------------
+---------------------
+
   - from Vojtech Pavlik <[email protected]>
 
 This is another very similar 90C65 card. Most of the switches and jumpers
 are the same as on other clones.
 
- _____________________________________________________________________
-|  ___________   |                         |            ______        |
-| |SW2 NODE ID|  |                         |           | XTAL |       |
-| |___________|  |  Hybrid IC              |           |______|       |
-|  ___________   |                         |                        __|    
-| |SW1 MEM+I/O|  |_________________________|                   LED1|__|)   
-| |___________|           1 2                                         |     
-|                     J3 |o|o| TIMEOUT                          ______|    
-|     ______________     |o|o|                                 |      |    
-|    |              |  ___________________                     | RJ   |    
-|    > EPROM SOCKET | |                   \                    |------|     
-|J2  |______________| |                    |                   |      |    
-||o|                  |                    |                   |______|
-||o| ROM ENABLE       |        SMC         |    _________             |
-|     _____________   |       90C65        |   |_________|       _____|    
-|    |             |  |                    |                    |     |___ 
-|    > RAM (2k)    |  |                    |                    | BNC |___|
-|    |_____________|  |                    |                    |_____|    
-|                     |____________________|                          |    
-| ________ IRQ 2 3 4 5 7                  ___________                 |
-||________|   |o|o|o|o|o|                |___________|                |
-|________   J1|o|o|o|o|o|                               ______________|
-         |                                             |
-         |_____________________________________________|
+::
 
-Legend:
+   _____________________________________________________________________
+  |  ___________   |                         |            ______        |
+  | |SW2 NODE ID|  |                         |           | XTAL |       |
+  | |___________|  |  Hybrid IC              |           |______|       |
+  |  ___________   |                         |                        __|
+  | |SW1 MEM+I/O|  |_________________________|                   LED1|__|)
+  | |___________|           1 2                                         |
+  |                     J3 |o|o| TIMEOUT                          ______|
+  |     ______________     |o|o|                                 |      |
+  |    |              |  ___________________                     | RJ   |
+  |    > EPROM SOCKET | |                   \                    |------|
+  |J2  |______________| |                    |                   |      |
+  ||o|                  |                    |                   |______|
+  ||o| ROM ENABLE       |        SMC         |    _________             |
+  |     _____________   |       90C65        |   |_________|       _____|
+  |    |             |  |                    |                    |     |___
+  |    > RAM (2k)    |  |                    |                    | BNC |___|
+  |    |_____________|  |                    |                    |_____|
+  |                     |____________________|                          |
+  | ________ IRQ 2 3 4 5 7                  ___________                 |
+  ||________|   |o|o|o|o|o|                |___________|                |
+  |________   J1|o|o|o|o|o|                               ______________|
+	   |                                             |
+	   |_____________________________________________|
 
-90C65       ARCNET Chip
-XTAL        20 MHz Crystal
-SW1 1-5     Base Memory Address Select
-    6-8     Base I/O Address Select
-SW2 1-8     Node ID Select (ID0-ID7)
-J1          IRQ Select
-J2          ROM Enable
-J3          Extra Timeout
-LED1        Activity LED 
-BNC         Coax connector (BUS ARCnet)
-RJ          Twisted Pair Connector (daisy chain)
+Legend::
+
+  90C65       ARCNET Chip
+  XTAL        20 MHz Crystal
+  SW1 1-5     Base Memory Address Select
+      6-8     Base I/O Address Select
+  SW2 1-8     Node ID Select (ID0-ID7)
+  J1          IRQ Select
+  J2          ROM Enable
+  J3          Extra Timeout
+  LED1        Activity LED
+  BNC         Coax connector (BUS ARCnet)
+  RJ          Twisted Pair Connector (daisy chain)
 
 
 Setting the Node ID
--------------------
+^^^^^^^^^^^^^^^^^^^
 
 The eight switches in SW2 are used to set the node ID. Each node attached to
 the network must have an unique node ID which must not be 0.  Switch 1 (ID0)
@@ -2097,7 +2159,7 @@ serves as the least significant bit (LSB).
 Setting one of the switches to Off means "1", On means "0".
 
 The node ID is the sum of the values of all switches set to "1"
-These values are:
+These values are::
 
    Switch | Label | Value
    -------|-------|-------
@@ -2111,10 +2173,10 @@ These values are:
      8    | ID7   | 128
 
 Setting the I/O Base Address
-----------------------------
+^^^^^^^^^^^^^^^^^^^^^^^^^^^^
 
 The last three switches in switch block SW1 are used to select one
-of eight possible I/O Base addresses using the following table:
+of eight possible I/O Base addresses using the following table::
 
 
    Switch      | Hex I/O
@@ -2122,7 +2184,7 @@ of eight possible I/O Base addresses using the following table:
    ------------|--------
    ON  ON  ON  |  260  (Manufacturer's default)
    OFF ON  ON  |  290
-   ON  OFF ON  |  2E0                         
+   ON  OFF ON  |  2E0
    OFF OFF ON  |  2F0
    ON  ON  OFF |  300
    OFF ON  OFF |  350
@@ -2131,35 +2193,38 @@ of eight possible I/O Base addresses using the following table:
 
 
 Setting the Base Memory (RAM) buffer Address
---------------------------------------------
+^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^
 
 The memory buffer (RAM) requires 2K. The base of this buffer can be
 located in any of eight positions. The address of the Boot Prom is
 memory base + 0x2000.
+
 Jumpers 3-5 of switch block SW1 select the Memory Base address.
 
+::
+
    Switch              | Hex RAM | Hex ROM
     1   2   3   4   5  | Address | Address *)
    --------------------|---------|-----------
    ON  ON  ON  ON  ON  |  C0000  |  C2000
-   ON  ON  OFF ON  ON  |  C4000  |  C6000  (Manufacturer's default) 
+   ON  ON  OFF ON  ON  |  C4000  |  C6000  (Manufacturer's default)
    ON  ON  ON  OFF ON  |  CC000  |  CE000
-   ON  ON  OFF OFF ON  |  D0000  |  D2000  
+   ON  ON  OFF OFF ON  |  D0000  |  D2000
    ON  ON  ON  ON  OFF |  D4000  |  D6000
    ON  ON  OFF ON  OFF |  D8000  |  DA000
    ON  ON  ON  OFF OFF |  DC000  |  DE000
    ON  ON  OFF OFF OFF |  E0000  |  E2000
 
-*) To enable the Boot ROM short the jumper J2.
+   *) To enable the Boot ROM short the jumper J2.
 
 The jumpers 1 and 2 probably add 0x0800 and 0x1000 to RAM address.
 
 
 Setting the Interrupt Line
---------------------------
+^^^^^^^^^^^^^^^^^^^^^^^^^^
 
 Jumpers 1-5 of the jumper block J1 control the IRQ level.  ON means
-shorted, OFF means open.
+shorted, OFF means open::
 
     Jumper              |  IRQ
     1   2   3   4   5   |
@@ -2172,19 +2237,21 @@ shorted, OFF means open.
 
 
 Setting the Timeout Parameters
-------------------------------
+^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^
 
-The jumpers J3 are used to set the timeout parameters. These two 
+The jumpers J3 are used to set the timeout parameters. These two
 jumpers are normally left open.
 
-  
-*****************************************************************************
+Thomas-Conrad
+=============
 
-** Thomas-Conrad **
 Model #500-6242-0097 REV A (8-bit card)
 ---------------------------------------
+
   - from Lars Karlsson <[email protected]>
 
+::
+
      ________________________________________________________
    |          ________   ________                           |_____
    |         |........| |........|                            |
@@ -2194,11 +2261,11 @@ Model #500-6242-0097 REV A (8-bit card)
    |                                              address |   |
    |    ______                                    switch  |   |
    |   |      |                                           |   |
-   |   |      |                                           |___|    
+   |   |      |                                           |___|
    |   |      |                                 ______        |___._
    |   |______|                                |______|         ____| BNC
    |                                            Jumper-        _____| Connector
-   |   Main chip                                block  _    __|   '  
+   |   Main chip                                block  _    __|   '
    |                                                  | |  |    RJ Connector
    |                                                  |_|  |    with 110 Ohm
    |                                                       |__  Terminator
@@ -2208,46 +2275,49 @@ Model #500-6242-0097 REV A (8-bit card)
    |   |___________|   |_____|                             |__
    |  Boot PROM socket IRQ-jumpers                            |_  Diagnostic
    |________                                       __          _| LED (red)
-            | | | | | | | | | | | | | | | | | | | |  |        |
-            | | | | | | | | | | | | | | | | | | | |  |________|
-                                                              |
-                                                              |
+	    | | | | | | | | | | | | | | | | | | | |  |        |
+	    | | | | | | | | | | | | | | | | | | | |  |________|
+							      |
+							      |
 
 And here are the settings for some of the switches and jumpers on the cards.
 
+::
 
-          I/O
+	    I/O
 
-         1 2 3 4 5 6 7 8
+	   1 2 3 4 5 6 7 8
 
-2E0----- 0 0 0 1 0 0 0 1
-2F0----- 0 0 0 1 0 0 0 0
-300----- 0 0 0 0 1 1 1 1
-350----- 0 0 0 0 1 1 1 0
+  2E0----- 0 0 0 1 0 0 0 1
+  2F0----- 0 0 0 1 0 0 0 0
+  300----- 0 0 0 0 1 1 1 1
+  350----- 0 0 0 0 1 1 1 0
 
 "0" in the above example means switch is off "1" means that it is on.
 
+::
 
-    ShMem address.
+      ShMem address.
 
-      1 2 3 4 5 6 7 8
+	1 2 3 4 5 6 7 8
 
-CX00--0 0 1 1 | |   |
-DX00--0 0 1 0       |
-X000--------- 1 1   |
-X400--------- 1 0   |
-X800--------- 0 1   |
-XC00--------- 0 0   
-ENHANCED----------- 1
-COMPATIBLE--------- 0
+  CX00--0 0 1 1 | |   |
+  DX00--0 0 1 0       |
+  X000--------- 1 1   |
+  X400--------- 1 0   |
+  X800--------- 0 1   |
+  XC00--------- 0 0
+  ENHANCED----------- 1
+  COMPATIBLE--------- 0
 
+::
 
-       IRQ
+	 IRQ
 
 
-   3 4 5 7 2
-   . . . . .
-   . . . . .
+     3 4 5 7 2
+     . . . . .
+     . . . . .
 
 
 There is a DIP-switch with 8 switches, used to set the shared memory address
@@ -2266,10 +2336,9 @@ varies by the type of card involved.  I fail to see how either of these
 enhance anything.  Send me more detailed information about this mode, or
 just use "compatible" mode instead.]
 
+Waterloo Microsystems Inc. ??
+=============================
 
-*****************************************************************************
-
-** Waterloo Microsystems Inc. ?? **
 8-bit card (C) 1985
 -------------------
   - from Robert Michael Best <[email protected]>
@@ -2283,103 +2352,104 @@ e-mail me.]
 
 The probe has not been able to detect the card on any of the J2 settings,
 and I tried them again with the "Waterloo" chip removed.
- 
- _____________________________________________________________________
-| \/  \/              ___  __ __                                      |
-| C4  C4     |^|     | M ||  ^  ||^|                                  |
-| --  --     |_|     | 5 ||     || | C3                               |
-| \/  \/      C10    |___||     ||_|                                  | 
-| C4  C4             _  _ |     |                 ??                  | 
-| --  --            | \/ ||     |                                     | 
-|                   |    ||     |                                     | 
-|                   |    ||  C1 |                                     | 
-|                   |    ||     |  \/                            _____|    
-|                   | C6 ||     |  C9                           |     |___ 
-|                   |    ||     |  --                           | BNC |___| 
-|                   |    ||     |          >C7|                 |_____|
-|                   |    ||     |                                     |
-| __ __             |____||_____|       1 2 3     6                   |
-||  ^  |     >C4|                      |o|o|o|o|o|o| J2    >C4|       |
-||     |                               |o|o|o|o|o|o|                  |
-|| C2  |     >C4|                                          >C4|       |
-||     |                                   >C8|                       |
-||     |       2 3 4 5 6 7  IRQ                            >C4|       |
-||_____|      |o|o|o|o|o|o| J3                                        |
-|_______      |o|o|o|o|o|o|                            _______________|
-        |                                             |
-        |_____________________________________________|
 
-C1 -- "COM9026
-       SMC 8638"
-      In a chip socket.
+::
 
-C2 -- "@Copyright
-       Waterloo Microsystems Inc.
-       1985"
-      In a chip Socket with info printed on a label covering a round window
-      showing the circuit inside. (The window indicates it is an EPROM chip.)
+   _____________________________________________________________________
+  | \/  \/              ___  __ __                                      |
+  | C4  C4     |^|     | M ||  ^  ||^|                                  |
+  | --  --     |_|     | 5 ||     || | C3                               |
+  | \/  \/      C10    |___||     ||_|                                  |
+  | C4  C4             _  _ |     |                 ??                  |
+  | --  --            | \/ ||     |                                     |
+  |                   |    ||     |                                     |
+  |                   |    ||  C1 |                                     |
+  |                   |    ||     |  \/                            _____|
+  |                   | C6 ||     |  C9                           |     |___
+  |                   |    ||     |  --                           | BNC |___|
+  |                   |    ||     |          >C7|                 |_____|
+  |                   |    ||     |                                     |
+  | __ __             |____||_____|       1 2 3     6                   |
+  ||  ^  |     >C4|                      |o|o|o|o|o|o| J2    >C4|       |
+  ||     |                               |o|o|o|o|o|o|                  |
+  || C2  |     >C4|                                          >C4|       |
+  ||     |                                   >C8|                       |
+  ||     |       2 3 4 5 6 7  IRQ                            >C4|       |
+  ||_____|      |o|o|o|o|o|o| J3                                        |
+  |_______      |o|o|o|o|o|o|                            _______________|
+	  |                                             |
+	  |_____________________________________________|
 
-C3 -- "COM9032
-       SMC 8643"
-      In a chip socket.
+  C1 -- "COM9026
+	 SMC 8638"
+	In a chip socket.
 
-C4 -- "74LS"
-      9 total no sockets.
+  C2 -- "@Copyright
+	 Waterloo Microsystems Inc.
+	 1985"
+	In a chip Socket with info printed on a label covering a round window
+	showing the circuit inside. (The window indicates it is an EPROM chip.)
 
-M5 -- "50006-136
-       20.000000 MHZ
-       MTQ-T1-S3
-       0 M-TRON 86-40"
-      Metallic case with 4 pins, no socket.
+  C3 -- "COM9032
+	 SMC 8643"
+	In a chip socket.
 
-C6 -- "MOSTEK@TC8643
-       MK6116N-20
-       MALAYSIA"
-      No socket.
+  C4 -- "74LS"
+	9 total no sockets.
 
-C7 -- No stamp or label but in a 20 pin chip socket.
+  M5 -- "50006-136
+	 20.000000 MHZ
+	 MTQ-T1-S3
+	 0 M-TRON 86-40"
+	Metallic case with 4 pins, no socket.
 
-C8 -- "PAL10L8CN
-       8623"
-      In a 20 pin socket.
+  C6 -- "MOSTEK@TC8643
+	 MK6116N-20
+	 MALAYSIA"
+	No socket.
 
-C9 -- "PAl16R4A-2CN
-       8641"
-      In a 20 pin socket.
+  C7 -- No stamp or label but in a 20 pin chip socket.
 
-C10 -- "M8640
-          NMC
-        9306N"
-       In an 8 pin socket.
+  C8 -- "PAL10L8CN
+	 8623"
+	In a 20 pin socket.
 
-?? -- Some components on a smaller board and attached with 20 pins all 
-      along the side closest to the BNC connector.  The are coated in a dark 
-      resin.
+  C9 -- "PAl16R4A-2CN
+	 8641"
+	In a 20 pin socket.
 
-On the board there are two jumper banks labeled J2 and J3. The 
-manufacturer didn't put a J1 on the board. The two boards I have both 
+  C10 -- "M8640
+	    NMC
+	  9306N"
+	 In an 8 pin socket.
+
+  ?? -- Some components on a smaller board and attached with 20 pins all
+	along the side closest to the BNC connector.  The are coated in a dark
+	resin.
+
+On the board there are two jumper banks labeled J2 and J3. The
+manufacturer didn't put a J1 on the board. The two boards I have both
 came with a jumper box for each bank.
 
-J2 -- Numbered 1 2 3 4 5 6. 
-      4 and 5 are not stamped due to solder points.
-       
-J3 -- IRQ 2 3 4 5 6 7
+::
 
-The board itself has a maple leaf stamped just above the irq jumpers 
-and "-2 46-86" beside C2. Between C1 and C6 "ASS 'Y 300163" and "@1986 
+  J2 -- Numbered 1 2 3 4 5 6.
+	4 and 5 are not stamped due to solder points.
+
+  J3 -- IRQ 2 3 4 5 6 7
+
+The board itself has a maple leaf stamped just above the irq jumpers
+and "-2 46-86" beside C2. Between C1 and C6 "ASS 'Y 300163" and "@1986
 CORMAN CUSTOM ELECTRONICS CORP." stamped just below the BNC connector.
 Below that "MADE IN CANADA"
 
-  
-*****************************************************************************
+No Name
+=======
 
-** No Name **
 8-bit cards, 16-bit cards
 -------------------------
+
   - from Juergen Seifert <[email protected]>
-  
-NONAME 8-BIT ARCNET
-===================
 
 I have named this ARCnet card "NONAME", since there is no name of any
 manufacturer on the Installation manual nor on the shipping box. The only
@@ -2388,8 +2458,10 @@ it is "Made in Taiwan"
 
 This description has been written by Juergen Seifert <[email protected]>
 using information from the Original
-                    "ARCnet Installation Manual"
 
+		    "ARCnet Installation Manual"
+
+::
 
     ________________________________________________________________
    | |STAR| BUS| T/P|                                               |
@@ -2416,32 +2488,32 @@ using information from the Original
        |        \ IRQ   / T T O                      |
        |__________________1_2_M______________________|
 
-Legend:
+Legend::
 
-COM90C65:       ARCnet Probe
-S1  1-8:    Node ID Select
-S2  1-3:    I/O Base Address Select
-    4-6:    Memory Base Address Select
-    7-8:    RAM Offset Select
-ET1, ET2    Extended Timeout Select
-ROM     ROM Enable Select
-CN              RG62 Coax Connector
-STAR| BUS | T/P Three fields for placing a sign (colored circle)
-                indicating the topology of the card
+  COM90C65:       ARCnet Probe
+  S1  1-8:    Node ID Select
+  S2  1-3:    I/O Base Address Select
+      4-6:    Memory Base Address Select
+      7-8:    RAM Offset Select
+  ET1, ET2    Extended Timeout Select
+  ROM     ROM Enable Select
+  CN              RG62 Coax Connector
+  STAR| BUS | T/P Three fields for placing a sign (colored circle)
+		  indicating the topology of the card
 
 Setting one of the switches to Off means "1", On means "0".
 
 
 Setting the Node ID
--------------------
+^^^^^^^^^^^^^^^^^^^
 
 The eight switches in group SW1 are used to set the node ID.
 Each node attached to the network must have an unique node ID which
 must be different from 0.
 Switch 8 serves as the least significant bit (LSB).
 
-The node ID is the sum of the values of all switches set to "1"  
-These values are:
+The node ID is the sum of the values of all switches set to "1"
+These values are::
 
     Switch | Value
     -------|-------
@@ -2454,30 +2526,30 @@ These values are:
       2    |  64
       1    | 128
 
-Some Examples:
+Some Examples::
 
-    Switch         | Hex     | Decimal 
+    Switch         | Hex     | Decimal
    1 2 3 4 5 6 7 8 | Node ID | Node ID
    ----------------|---------|---------
    0 0 0 0 0 0 0 0 |    not allowed
-   0 0 0 0 0 0 0 1 |    1    |    1 
+   0 0 0 0 0 0 0 1 |    1    |    1
    0 0 0 0 0 0 1 0 |    2    |    2
    0 0 0 0 0 0 1 1 |    3    |    3
        . . .       |         |
    0 1 0 1 0 1 0 1 |   55    |   85
        . . .       |         |
    1 0 1 0 1 0 1 0 |   AA    |  170
-       . . .       |         |  
+       . . .       |         |
    1 1 1 1 1 1 0 1 |   FD    |  253
    1 1 1 1 1 1 1 0 |   FE    |  254
    1 1 1 1 1 1 1 1 |   FF    |  255
 
 
 Setting the I/O Base Address
-----------------------------
+^^^^^^^^^^^^^^^^^^^^^^^^^^^^
 
 The first three switches in switch group SW2 are used to select one
-of eight possible I/O Base addresses using the following table
+of eight possible I/O Base addresses using the following table::
 
    Switch      | Hex I/O
     1   2   3  | Address
@@ -2493,7 +2565,7 @@ of eight possible I/O Base addresses using the following table
 
 
 Setting the Base Memory (RAM) buffer Address
---------------------------------------------
+^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^
 
 The memory buffer requires 2K of a 16K block of RAM. The base of this
 16K block can be located in any of eight positions.
@@ -2501,6 +2573,8 @@ Switches 4-6 of switch group SW2 select the Base of the 16K block.
 Within that 16K address space, the buffer may be assigned any one of four
 positions, determined by the offset, switches 7 and 8 of group SW2.
 
+::
+
    Switch     | Hex RAM | Hex ROM
    4 5 6  7 8 | Address | Address *)
    -----------|---------|-----------
@@ -2508,60 +2582,62 @@ positions, determined by the offset, switches 7 and 8 of group SW2.
    0 0 0  0 1 |  C0800  |  C2000
    0 0 0  1 0 |  C1000  |  C2000
    0 0 0  1 1 |  C1800  |  C2000
-              |         |
+	      |         |
    0 0 1  0 0 |  C4000  |  C6000
    0 0 1  0 1 |  C4800  |  C6000
    0 0 1  1 0 |  C5000  |  C6000
    0 0 1  1 1 |  C5800  |  C6000
-              |         |
+	      |         |
    0 1 0  0 0 |  CC000  |  CE000
    0 1 0  0 1 |  CC800  |  CE000
    0 1 0  1 0 |  CD000  |  CE000
    0 1 0  1 1 |  CD800  |  CE000
-              |         |
+	      |         |
    0 1 1  0 0 |  D0000  |  D2000  (Manufacturer's default)
    0 1 1  0 1 |  D0800  |  D2000
    0 1 1  1 0 |  D1000  |  D2000
    0 1 1  1 1 |  D1800  |  D2000
-              |         |
+	      |         |
    1 0 0  0 0 |  D4000  |  D6000
    1 0 0  0 1 |  D4800  |  D6000
    1 0 0  1 0 |  D5000  |  D6000
    1 0 0  1 1 |  D5800  |  D6000
-              |         |
+	      |         |
    1 0 1  0 0 |  D8000  |  DA000
    1 0 1  0 1 |  D8800  |  DA000
    1 0 1  1 0 |  D9000  |  DA000
    1 0 1  1 1 |  D9800  |  DA000
-              |         |
+	      |         |
    1 1 0  0 0 |  DC000  |  DE000
    1 1 0  0 1 |  DC800  |  DE000
    1 1 0  1 0 |  DD000  |  DE000
    1 1 0  1 1 |  DD800  |  DE000
-              |         |
+	      |         |
    1 1 1  0 0 |  E0000  |  E2000
    1 1 1  0 1 |  E0800  |  E2000
    1 1 1  1 0 |  E1000  |  E2000
    1 1 1  1 1 |  E1800  |  E2000
-  
-*) To enable the 8K Boot PROM install the jumper ROM.
-   The default is jumper ROM not installed.
+
+   *) To enable the 8K Boot PROM install the jumper ROM.
[… more lines in the raw message]

Lines of this file are not shown. View the raw message.

Documentation/networking/index.rst +1 -0
index 96ffad845fd9..5da18e024fcb 100644

Lines of this file are not shown. View the raw message.

The rest of this diff is not shown. View the raw message.

Signature · 1 line
2.25.4

Part of the diff is not shown here. View the raw message.

#5 lore raw

PATCH 5/38 docs: networking: convert arcnet.txt to ReST

In reply to Mauro Carvalho Chehab

- add SPDX header;
- use document title markup;
- add notes markups;
- mark code blocks and literals as such;
- mark tables as such;
- adjust identation, whitespaces and blank lines;
- add to networking/index.rst.

---
 .../networking/{arcnet.txt => arcnet.rst}     | 348 ++++++++++--------
 Documentation/networking/index.rst            |   1 +
 drivers/net/arcnet/Kconfig                    |   6 +-
 3 files changed, 197 insertions(+), 158 deletions(-)
 rename Documentation/networking/{arcnet.txt => arcnet.rst} (76%)
Documentation/networking/arcnet.rst renamed from Documentation/networking/arcnet.txt +193 -155
similarity index 76%
rename from Documentation/networking/arcnet.txt
rename to Documentation/networking/arcnet.rst
index aff97f47c05c..e93d9820f0f1 100644
@@ -1,11 +1,18 @@
-----------------------------------------------------------------------------
-NOTE:  See also arcnet-hardware.txt in this directory for jumper-setting
-and cabling information if you're like many of us and didn't happen to get a
-manual with your ARCnet card.
-----------------------------------------------------------------------------
+.. SPDX-License-Identifier: GPL-2.0
+
+======
+ARCnet
+======
+
+.. note::
+
+   See also arcnet-hardware.txt in this directory for jumper-setting
+   and cabling information if you're like many of us and didn't happen to get a
+   manual with your ARCnet card.
 
 Since no one seems to listen to me otherwise, perhaps a poem will get your
-attention:
+attention::
+
 		This driver's getting fat and beefy,
 		But my cat is still named Fifi.
 
@@ -24,28 +31,21 @@ Come on, be a sport!  Send me a success report!
 (hey, that was even better than my original poem... this is getting bad!)
 
 
---------
-WARNING:
---------
+.. warning::
 
-If you don't e-mail me about your success/failure soon, I may be forced to
-start SINGING.  And we don't want that, do we?
+   If you don't e-mail me about your success/failure soon, I may be forced to
+   start SINGING.  And we don't want that, do we?
 
-(You know, it might be argued that I'm pushing this point a little too much. 
-If you think so, why not flame me in a quick little e-mail?  Please also
-include the type of card(s) you're using, software, size of network, and
-whether it's working or not.)
+   (You know, it might be argued that I'm pushing this point a little too much.
+   If you think so, why not flame me in a quick little e-mail?  Please also
+   include the type of card(s) you're using, software, size of network, and
+   whether it's working or not.)
 
-My e-mail address is: [email protected]
+   My e-mail address is: [email protected]
 
-
----------------------------------------------------------------------------
-
-			
 These are the ARCnet drivers for Linux.
 
-
-This new release (2.91) has been put together by David Woodhouse 
+This new release (2.91) has been put together by David Woodhouse
 <[email protected]>, in an attempt to tidy up the driver after adding support
 for yet another chipset. Now the generic support has been separated from the
 individual chipset drivers, and the source files aren't quite so packed with
@@ -62,12 +62,13 @@ included and seems to be working fine!
 Where do I discuss these drivers?
 ---------------------------------
 
-Tomasz has been so kind as to set up a new and improved mailing list. 
+Tomasz has been so kind as to set up a new and improved mailing list.
 Subscribe by sending a message with the BODY "subscribe linux-arcnet YOUR
 REAL NAME" to [email protected].  Then, to submit messages to the
 list, mail to [email protected].
 
 There are archives of the mailing list at:
+
 	http://epistolary.org/mailman/listinfo.cgi/arcnet
 
 The people on [email protected] (now defunct, replaced by
@@ -80,17 +81,20 @@ Other Drivers and Info
 ----------------------
 
 You can try my ARCNET page on the World Wide Web at:
-	http://www.qis.net/~jschmitz/arcnet/	
+
+	http://www.qis.net/~jschmitz/arcnet/
 
 Also, SMC (one of the companies that makes ARCnet cards) has a WWW site you
 might be interested in, which includes several drivers for various cards
 including ARCnet.  Try:
+
 	http://www.smc.com/
-	
+
 Performance Technologies makes various network software that supports
 ARCnet:
+
 	http://www.perftech.com/ or ftp to ftp.perftech.com.
-	
+
 Novell makes a networking stack for DOS which includes ARCnet drivers.  Try
 FTPing to ftp.novell.com.
 
@@ -99,19 +103,20 @@ one you'll want to use with ARCnet cards) from
 oak.oakland.edu:/simtel/msdos/pktdrvr. It won't work perfectly on a 386+
 without patches, though, and also doesn't like several cards.  Fixed
 versions are available on my WWW page, or via e-mail if you don't have WWW
-access. 
+access.
 
 
 Installing the Driver
 ---------------------
 
-All you will need to do in order to install the driver is:
+All you will need to do in order to install the driver is::
+
 	make config
-		(be sure to choose ARCnet in the network devices 
+		(be sure to choose ARCnet in the network devices
 		and at least one chipset driver.)
 	make clean
 	make zImage
-	
+
 If you obtained this ARCnet package as an upgrade to the ARCnet driver in
 your current kernel, you will need to first copy arcnet.c over the one in
 the linux/drivers/net directory.
@@ -125,10 +130,12 @@ There are four chipset options:
 
 This is the normal ARCnet card, which you've probably got. This is the only
 chipset driver which will autoprobe if not told where the card is.
-It following options on the command line:
+It following options on the command line::
+
  com90xx=[<io>[,<irq>[,<shmem>]]][,<name>] | <name>
 
-If you load the chipset support as a module, the options are:
+If you load the chipset support as a module, the options are::
+
  io=<io> irq=<irq> shmem=<shmem> device=<name>
 
 To disable the autoprobe, just specify "com90xx=" on the kernel command line.
@@ -136,14 +143,17 @@ To specify the name alone, but allow autoprobe, just put "com90xx=<name>"
 
  2. ARCnet COM20020 chipset.
 
-This is the new chipset from SMC with support for promiscuous mode (packet 
+This is the new chipset from SMC with support for promiscuous mode (packet
 sniffing), extra diagnostic information, etc. Unfortunately, there is no
 sensible method of autoprobing for these cards. You must specify the I/O
 address on the kernel command line.
-The command line options are:
+
+The command line options are::
+
  com20020=<io>[,<irq>[,<node_ID>[,backplane[,CKP[,timeout]]]]][,name]
 
-If you load the chipset support as a module, the options are:
+If you load the chipset support as a module, the options are::
+
  io=<io> irq=<irq> node=<node_ID> backplane=<backplane> clock=<CKP>
  timeout=<timeout> device=<name>
 
@@ -160,8 +170,10 @@ you have a card which doesn't support shared memory, or (strangely) in case
 you have so many ARCnet cards in your machine that you run out of shmem slots.
 If you don't give the IO address on the kernel command line, then the driver
 will not find the card.
-The command line options are:
- com90io=<io>[,<irq>][,<name>] 
+
+The command line options are::
+
+ com90io=<io>[,<irq>][,<name>]
 
 If you load the chipset support as a module, the options are:
  io=<io> irq=<irq> device=<name>
@@ -169,44 +181,49 @@ If you load the chipset support as a module, the options are:
  4. ARCnet RIM I cards.
 
 These are COM90xx chips which are _completely_ memory mapped. The support for
-these is not tested. If you have one, please mail the author with a success 
+these is not tested. If you have one, please mail the author with a success
 report. All options must be specified, except the device name.
-Command line options:
+Command line options::
+
  arcrimi=<shmem>,<irq>,<node_ID>[,<name>]
 
-If you load the chipset support as a module, the options are:
+If you load the chipset support as a module, the options are::
+
  shmem=<shmem> irq=<irq> node=<node_ID> device=<name>
 
 
 Loadable Module Support
 -----------------------
 
-Configure and rebuild Linux.  When asked, answer 'm' to "Generic ARCnet 
+Configure and rebuild Linux.  When asked, answer 'm' to "Generic ARCnet
 support" and to support for your ARCnet chipset if you want to use the
-loadable module. You can also say 'y' to "Generic ARCnet support" and 'm' 
+loadable module. You can also say 'y' to "Generic ARCnet support" and 'm'
 to the chipset support if you wish.
 
+::
+
 	make config
-	make clean	
+	make clean
 	make zImage
 	make modules
-	
+
 If you're using a loadable module, you need to use insmod to load it, and
 you can specify various characteristics of your card on the command
 line.  (In recent versions of the driver, autoprobing is much more reliable
 and works as a module, so most of this is now unnecessary.)
 
-For example:
+For example::
+
 	cd /usr/src/linux/modules
 	insmod arcnet.o
 	insmod com90xx.o
 	insmod com20020.o io=0x2e0 device=eth1
-	
+
 
 Using the Driver
 ----------------
 
-If you build your kernel with ARCnet COM90xx support included, it should 
+If you build your kernel with ARCnet COM90xx support included, it should
 probe for your card automatically when you boot. If you use a different
 chipset driver complied into the kernel, you must give the necessary options
 on the kernel command line, as detailed above.
@@ -224,69 +241,78 @@ Multiple Cards in One Computer
 ------------------------------
 
 Linux has pretty good support for this now, but since I've been busy, the
-ARCnet driver has somewhat suffered in this respect. COM90xx support, if 
-compiled into the kernel, will (try to) autodetect all the installed cards. 
+ARCnet driver has somewhat suffered in this respect. COM90xx support, if
+compiled into the kernel, will (try to) autodetect all the installed cards.
 
-If you have other cards, with support compiled into the kernel, then you can 
-just repeat the options on the kernel command line, e.g.:
-LILO: linux com20020=0x2e0 com20020=0x380 com90io=0x260
+If you have other cards, with support compiled into the kernel, then you can
+just repeat the options on the kernel command line, e.g.::
+
+	LILO: linux com20020=0x2e0 com20020=0x380 com90io=0x260
+
+If you have the chipset support built as a loadable module, then you need to
+do something like this::
 
-If you have the chipset support built as a loadable module, then you need to 
-do something like this:
 	insmod -o arc0 com90xx
 	insmod -o arc1 com20020 io=0x2e0
 	insmod -o arc2 com90xx
+
 The ARCnet drivers will now sort out their names automatically.
 
 
 How do I get it to work with...?
 --------------------------------
 
-NFS: Should be fine linux->linux, just pretend you're using Ethernet cards. 
-        oak.oakland.edu:/simtel/msdos/nfs has some nice DOS clients.  There
-        is also a DOS-based NFS server called SOSS.  It doesn't multitask
-        quite the way Linux does (actually, it doesn't multitask AT ALL) but
-        you never know what you might need.
-        
-        With AmiTCP (and possibly others), you may need to set the following
-        options in your Amiga nfstab:  MD 1024 MR 1024 MW 1024
-        (Thanks to Christian Gottschling <[email protected]>
+NFS:
+	Should be fine linux->linux, just pretend you're using Ethernet cards.
+	oak.oakland.edu:/simtel/msdos/nfs has some nice DOS clients.  There
+	is also a DOS-based NFS server called SOSS.  It doesn't multitask
+	quite the way Linux does (actually, it doesn't multitask AT ALL) but
+	you never know what you might need.
+
+	With AmiTCP (and possibly others), you may need to set the following
+	options in your Amiga nfstab:  MD 1024 MR 1024 MW 1024
+	(Thanks to Christian Gottschling <[email protected]>
 	for this.)
-	
+
 	Probably these refer to maximum NFS data/read/write block sizes.  I
 	don't know why the defaults on the Amiga didn't work; write to me if
 	you know more.
 
-DOS: If you're using the freeware arcether.com, you might want to install
-        the driver patch from my web page.  It helps with PC/TCP, and also
-        can get arcether to load if it timed out too quickly during
-        initialization.  In fact, if you use it on a 386+ you REALLY need
-        the patch, really.
-	
-Windows:  See DOS :)  Trumpet Winsock works fine with either the Novell or
+DOS:
+	If you're using the freeware arcether.com, you might want to install
+	the driver patch from my web page.  It helps with PC/TCP, and also
+	can get arcether to load if it timed out too quickly during
+	initialization.  In fact, if you use it on a 386+ you REALLY need
+	the patch, really.
+
+Windows:
+	See DOS :)  Trumpet Winsock works fine with either the Novell or
 	Arcether client, assuming you remember to load winpkt of course.
 
-LAN Manager and Windows for Workgroups: These programs use protocols that
-        are incompatible with the Internet standard.  They try to pretend
-        the cards are Ethernet, and confuse everyone else on the network. 
-        
-        However, v2.00 and higher of the Linux ARCnet driver supports this
-        protocol via the 'arc0e' device.  See the section on "Multiprotocol
-        Support" for more information.
+LAN Manager and Windows for Workgroups:
+	These programs use protocols that
+	are incompatible with the Internet standard.  They try to pretend
+	the cards are Ethernet, and confuse everyone else on the network.
+
+	However, v2.00 and higher of the Linux ARCnet driver supports this
+	protocol via the 'arc0e' device.  See the section on "Multiprotocol
+	Support" for more information.
 
 	Using the freeware Samba server and clients for Linux, you can now
 	interface quite nicely with TCP/IP-based WfWg or Lan Manager
 	networks.
-	
-Windows 95: Tools are included with Win95 that let you use either the LANMAN
+
+Windows 95:
+	Tools are included with Win95 that let you use either the LANMAN
 	style network drivers (NDIS) or Novell drivers (ODI) to handle your
 	ARCnet packets.  If you use ODI, you'll need to use the 'arc0'
-	device with Linux.  If you use NDIS, then try the 'arc0e' device. 
+	device with Linux.  If you use NDIS, then try the 'arc0e' device.
 	See the "Multiprotocol Support" section below if you need arc0e,
 	you're completely insane, and/or you need to build some kind of
 	hybrid network that uses both encapsulation types.
 
-OS/2: I've been told it works under Warp Connect with an ARCnet driver from
+OS/2:
+	I've been told it works under Warp Connect with an ARCnet driver from
 	SMC.  You need to use the 'arc0e' interface for this.  If you get
 	the SMC driver to work with the TCP/IP stuff included in the
 	"normal" Warp Bonus Pack, let me know.
@@ -295,7 +321,8 @@ OS/2: I've been told it works under Warp Connect with an ARCnet driver from
 	which should use the same protocol as WfWg does.  I had no luck
 	installing it under Warp, however.  Please mail me with any results.
 
-NetBSD/AmiTCP: These use an old version of the Internet standard ARCnet
+NetBSD/AmiTCP:
+	These use an old version of the Internet standard ARCnet
 	protocol (RFC1051) which is compatible with the Linux driver v2.10
 	ALPHA and above using the arc0s device. (See "Multiprotocol ARCnet"
 	below.)  ** Newer versions of NetBSD apparently support RFC1201.
@@ -307,16 +334,17 @@ Using Multiprotocol ARCnet
 The ARCnet driver v2.10 ALPHA supports three protocols, each on its own
 "virtual network device":
 
-	arc0  - RFC1201 protocol, the official Internet standard which just
-		happens to be 100% compatible with Novell's TRXNET driver. 
+	======  ===============================================================
+	arc0	RFC1201 protocol, the official Internet standard which just
+		happens to be 100% compatible with Novell's TRXNET driver.
 		Version 1.00 of the ARCnet driver supported _only_ this
 		protocol.  arc0 is the fastest of the three protocols (for
 		whatever reason), and allows larger packets to be used
-		because it supports RFC1201 "packet splitting" operations. 
+		because it supports RFC1201 "packet splitting" operations.
 		Unless you have a specific need to use a different protocol,
 		I strongly suggest that you stick with this one.
-		
-	arc0e - "Ethernet-Encapsulation" which sends packets over ARCnet
+
+	arc0e	"Ethernet-Encapsulation" which sends packets over ARCnet
 		that are actually a lot like Ethernet packets, including the
 		6-byte hardware addresses.  This protocol is compatible with
 		Microsoft's NDIS ARCnet driver, like the one in WfWg and
@@ -328,8 +356,8 @@ The ARCnet driver v2.10 ALPHA supports three protocols, each on its own
 		fit.  arc0e also works slightly more slowly than arc0, for
 		reasons yet to be determined.  (Probably it's the smaller
 		MTU that does it.)
-		
-	arc0s - The "[s]imple" RFC1051 protocol is the "previous" Internet
+
+	arc0s	The "[s]imple" RFC1051 protocol is the "previous" Internet
 		standard that is completely incompatible with the new
 		standard.  Some software today, however, continues to
 		support the old standard (and only the old standard)
@@ -338,9 +366,10 @@ The ARCnet driver v2.10 ALPHA supports three protocols, each on its own
 		smaller than the Internet "requirement," so it's quite
 		possible that you may run into problems.  It's also slower
 		than RFC1201 by about 25%, for the same reason as arc0e.
-		
+
 		The arc0s support was contributed by Tomasz Motylewski
 		and modified somewhat by me.  Bugs are probably my fault.
+	======  ===============================================================
 
 You can choose not to compile arc0e and arc0s into the driver if you want -
 this will save you a bit of memory and avoid confusion when eg. trying to
@@ -358,19 +387,21 @@ can set up your network then:
    two available protocols.  As mentioned above, it's a good idea to use
    only arc0 unless you have a good reason (like some other software, ie.
    WfWg, that only works with arc0e).
-   
-   If you need only arc0, then the following commands should get you going:
-   	ifconfig arc0 MY.IP.ADD.RESS
-   	route add MY.IP.ADD.RESS arc0
-   	route add -net SUB.NET.ADD.RESS arc0
-   	[add other local routes here]
-   	
-   If you need arc0e (and only arc0e), it's a little different:
-   	ifconfig arc0 MY.IP.ADD.RESS
-   	ifconfig arc0e MY.IP.ADD.RESS
-   	route add MY.IP.ADD.RESS arc0e
-   	route add -net SUB.NET.ADD.RESS arc0e
-   
+
+   If you need only arc0, then the following commands should get you going::
+
+	ifconfig arc0 MY.IP.ADD.RESS
+	route add MY.IP.ADD.RESS arc0
+	route add -net SUB.NET.ADD.RESS arc0
+	[add other local routes here]
+
+   If you need arc0e (and only arc0e), it's a little different::
+
+	ifconfig arc0 MY.IP.ADD.RESS
+	ifconfig arc0e MY.IP.ADD.RESS
+	route add MY.IP.ADD.RESS arc0e
+	route add -net SUB.NET.ADD.RESS arc0e
+
    arc0s works much the same way as arc0e.
 
 
@@ -391,29 +422,32 @@ can set up your network then:
    XT (patience), however, does not have its own Internet IP address and so
    I assigned it one on a "private subnet" (as defined by RFC1597).
 
-   To start with, take a simple network with just insight and freedom. 
+   To start with, take a simple network with just insight and freedom.
    Insight needs to:
-   	- talk to freedom via RFC1201 (arc0) protocol, because I like it
+
+	- talk to freedom via RFC1201 (arc0) protocol, because I like it
 	  more and it's faster.
 	- use freedom as its Internet gateway.
-	
-   That's pretty easy to do.  Set up insight like this:
-   	ifconfig arc0 insight
-   	route add insight arc0
-   	route add freedom arc0	/* I would use the subnet here (like I said
+
+   That's pretty easy to do.  Set up insight like this::
+
+	ifconfig arc0 insight
+	route add insight arc0
+	route add freedom arc0	/* I would use the subnet here (like I said
 					to to in "single protocol" above),
-   					but the rest of the subnet
-   					unfortunately lies across the PPP
-   					link on freedom, which confuses
-   					things. */
-   	route add default gw freedom
-   	
-   And freedom gets configured like so:
-   	ifconfig arc0 freedom
-   	route add freedom arc0
-   	route add insight arc0
-   	/* and default gateway is configured by pppd */
-   	
+					but the rest of the subnet
+					unfortunately lies across the PPP
+					link on freedom, which confuses
+					things. */
+	route add default gw freedom
+
+   And freedom gets configured like so::
+
+	ifconfig arc0 freedom
+	route add freedom arc0
+	route add insight arc0
+	/* and default gateway is configured by pppd */
+
    Great, now insight talks to freedom directly on arc0, and sends packets
    to the Internet through freedom.  If you didn't know how to do the above,
    you should probably stop reading this section now because it only gets
@@ -425,7 +459,7 @@ can set up your network then:
    Internet.  (Recall that patience has a "private IP address" which won't
    work on the Internet; that's okay, I configured Linux IP masquerading on
    freedom for this subnet).
-   
+
    So patience (necessarily; I don't have another IP number from my
    provider) has an IP address on a different subnet than freedom and
    insight, but needs to use freedom as an Internet gateway.  Worse, most
@@ -435,53 +469,54 @@ can set up your network then:
    insight, patience WILL send through its default gateway, regardless of
    the fact that both freedom and insight (courtesy of the arc0e device)
    could understand a direct transmission.
-   
-   I compensate by giving freedom an extra IP address - aliased 'gatekeeper'
-   - that is on my private subnet, the same subnet that patience is on.  I
+
+   I compensate by giving freedom an extra IP address - aliased 'gatekeeper' -
+   that is on my private subnet, the same subnet that patience is on.  I
    then define gatekeeper to be the default gateway for patience.
-   
-   To configure freedom (in addition to the commands above):
-   	ifconfig arc0e gatekeeper
-   	route add gatekeeper arc0e
-   	route add patience arc0e
-   
+
+   To configure freedom (in addition to the commands above)::
+
+	ifconfig arc0e gatekeeper
+	route add gatekeeper arc0e
+	route add patience arc0e
+
    This way, freedom will send all packets for patience through arc0e,
    giving its IP address as gatekeeper (on the private subnet).  When it
    talks to insight or the Internet, it will use its "freedom" Internet IP
    address.
-   
-   You will notice that we haven't configured the arc0e device on insight. 
+
+   You will notice that we haven't configured the arc0e device on insight.
    This would work, but is not really necessary, and would require me to
    assign insight another special IP number from my private subnet.  Since
    both insight and patience are using freedom as their default gateway, the
    two can already talk to each other.
-   
+
    It's quite fortunate that I set things up like this the first time (cough
    cough) because it's really handy when I boot insight into DOS.  There, it
-   runs the Novell ODI protocol stack, which only works with RFC1201 ARCnet. 
+   runs the Novell ODI protocol stack, which only works with RFC1201 ARCnet.
    In this mode it would be impossible for insight to communicate directly
    with patience, since the Novell stack is incompatible with Microsoft's
    Ethernet-Encap.  Without changing any settings on freedom or patience, I
    simply set freedom as the default gateway for insight (now in DOS,
    remember) and all the forwarding happens "automagically" between the two
    hosts that would normally not be able to communicate at all.
-   
+
    For those who like diagrams, I have created two "virtual subnets" on the
-   same physical ARCnet wire.  You can picture it like this:
-   
-                                                    
-          [RFC1201 NETWORK]                   [ETHER-ENCAP NETWORK]
+   same physical ARCnet wire.  You can picture it like this::
+
+
+	  [RFC1201 NETWORK]                   [ETHER-ENCAP NETWORK]
       (registered Internet subnet)           (RFC1597 private subnet)
-  
-                             (IP Masquerade)
-          /---------------\         *            /---------------\
-          |               |         *            |               |
-          |               +-Freedom-*-Gatekeeper-+               |
-          |               |    |    *            |               |
-          \-------+-------/    |    *            \-------+-------/
-                  |            |                         |
-               Insight         |                      Patience
-                           (Internet)
+
+			     (IP Masquerade)
+	  /---------------\         *            /---------------\
+	  |               |         *            |               |
+	  |               +-Freedom-*-Gatekeeper-+               |
+	  |               |    |    *            |               |
+	  \-------+-------/    |    *            \-------+-------/
+		  |            |                         |
+	       Insight         |                      Patience
+			   (Internet)
 
 
 
@@ -491,6 +526,7 @@ It works: what now?
 Send mail describing your setup, preferably including driver version, kernel
 version, ARCnet card model, CPU type, number of systems on your network, and
 list of software in use to me at the following address:
+
 	[email protected]
 
 I do send (sometimes automated) replies to all messages I receive.  My email
@@ -525,7 +561,7 @@ this, you should grab the pertinent RFCs. (some are listed near the top of
 arcnet.c).  arcdump assumes your card is at 0xD0000.  If it isn't, edit the
 script.
 
-Buffers 0 and 1 are used for receiving, and Buffers 2 and 3 are for sending. 
+Buffers 0 and 1 are used for receiving, and Buffers 2 and 3 are for sending.
 Ping-pong buffers are implemented both ways.
 
 If your debug level includes D_DURING and you did NOT define SLOW_XMIT_COPY,
@@ -535,9 +571,11 @@ decides that the driver is broken).  During a transmit, unused parts of the
 buffer will be cleared to 0x42 as well.  This is to make it easier to figure
 out which bytes are being used by a packet.
 
-You can change the debug level without recompiling the kernel by typing:
+You can change the debug level without recompiling the kernel by typing::
+
 	ifconfig arc0 down metric 1xxx
 	/etc/rc.d/rc.inet1
+
 where "xxx" is the debug level you want.  For example, "metric 1015" would put
 you at debug level 15.  Debug level 7 is currently the default.
 
@@ -546,7 +584,7 @@ combination of different debug flags; so debug level 7 is really 1+2+4 or
 D_NORMAL+D_EXTRA+D_INIT.  To include D_DURING, you would add 16 to this,
 resulting in debug level 23.
 
-If you don't understand that, you probably don't want to know anyway. 
+If you don't understand that, you probably don't want to know anyway.
 E-mail me about your problem.
 
 
Documentation/networking/index.rst +1 -0
index 5da18e024fcb..3e0a4bb23ef9 100644
@@ -40,6 +40,7 @@ Contents:
    6pack
    altera_tse
    arcnet-hardware
+   arcnet
 
 .. only::  subproject and html
 
drivers/net/arcnet/Kconfig +3 -3
index 27551bf3d7e4..43eef60653b2 100644
@@ -9,7 +9,7 @@ menuconfig ARCNET
 	---help---
 	  If you have a network card of this type, say Y and check out the
 	  (arguably) beautiful poetry in
-	  <file:Documentation/networking/arcnet.txt>.
+	  <file:Documentation/networking/arcnet.rst>.
 
 	  You need both this driver, and the driver for the particular ARCnet
 	  chipset of your card. If you don't know, then it's probably a
@@ -28,7 +28,7 @@ config ARCNET_1201
 	  arc0 device.  You need to say Y here to communicate with
 	  industry-standard RFC1201 implementations, like the arcether.com
 	  packet driver or most DOS/Windows ODI drivers.  Please read the
-	  ARCnet documentation in <file:Documentation/networking/arcnet.txt>
+	  ARCnet documentation in <file:Documentation/networking/arcnet.rst>
 	  for more information about using arc0.
 
 config ARCNET_1051
@@ -42,7 +42,7 @@ config ARCNET_1051
 	  industry-standard RFC1201 implementations, like the arcether.com
 	  packet driver or most DOS/Windows ODI drivers. RFC1201 is included
 	  automatically as the arc0 device. Please read the ARCnet
-	  documentation in <file:Documentation/networking/arcnet.txt> for more
+	  documentation in <file:Documentation/networking/arcnet.rst> for more
 	  information about using arc0e and arc0s.
 
 config ARCNET_RAW
Signature · 1 line
2.25.4
#6 lore raw

PATCH 6/38 docs: networking: convert atm.txt to ReST

In reply to Mauro Carvalho Chehab

There isn't much to be done here. Just:

- add SPDX header;
- add a document title.

---
 Documentation/networking/{atm.txt => atm.rst} | 6 ++++++
 Documentation/networking/index.rst            | 1 +
 net/atm/Kconfig                               | 2 +-
 3 files changed, 8 insertions(+), 1 deletion(-)
 rename Documentation/networking/{atm.txt => atm.rst} (89%)
Documentation/networking/atm.rst renamed from Documentation/networking/atm.txt +6 -0
similarity index 89%
rename from Documentation/networking/atm.txt
rename to Documentation/networking/atm.rst
index 82921cee77fe..c1df8c038525 100644
@@ -1,3 +1,9 @@
+.. SPDX-License-Identifier: GPL-2.0
+
+===
+ATM
+===
+
 In order to use anything but the most primitive functions of ATM,
 several user-mode programs are required to assist the kernel. These
 programs and related material can be found via the ATM on Linux Web
Documentation/networking/index.rst +1 -0
index 3e0a4bb23ef9..841f3c3905d5 100644
@@ -41,6 +41,7 @@ Contents:
    altera_tse
    arcnet-hardware
    arcnet
+   atm
 
 .. only::  subproject and html
 
net/atm/Kconfig +1 -1
index 271f682e8438..e61dcc9f85b2 100644
@@ -16,7 +16,7 @@ config ATM
 	  of your ATM card below.
 
 	  Note that you need a set of user-space programs to actually make use
-	  of ATM.  See the file <file:Documentation/networking/atm.txt> for
+	  of ATM.  See the file <file:Documentation/networking/atm.rst> for
 	  further details.
 
 config ATM_CLIP
Signature · 1 line
2.25.4
#7 lore raw

PATCH 7/38 docs: networking: convert ax25.txt to ReST

In reply to Mauro Carvalho Chehab

There isn't much to be done here. Just:

- add SPDX header;
- add a document title.

---
 Documentation/networking/{ax25.txt => ax25.rst} | 6 ++++++
 Documentation/networking/index.rst              | 1 +
 net/ax25/Kconfig                                | 6 +++---
 3 files changed, 10 insertions(+), 3 deletions(-)
 rename Documentation/networking/{ax25.txt => ax25.rst} (91%)
Documentation/networking/ax25.rst renamed from Documentation/networking/ax25.txt +6 -0
similarity index 91%
rename from Documentation/networking/ax25.txt
rename to Documentation/networking/ax25.rst
index 8257dbf9be57..824afd7002db 100644
@@ -1,3 +1,9 @@
+.. SPDX-License-Identifier: GPL-2.0
+
+=====
+AX.25
+=====
+
 To use the amateur radio protocols within Linux you will need to get a
 suitable copy of the AX.25 Utilities. More detailed information about
 AX.25, NET/ROM and ROSE, associated programs and and utilities can be
Documentation/networking/index.rst +1 -0
index 841f3c3905d5..6a5858b27cf6 100644
@@ -42,6 +42,7 @@ Contents:
    arcnet-hardware
    arcnet
    atm
+   ax25
 
 .. only::  subproject and html
 
net/ax25/Kconfig +3 -3
index 043fd5437809..97d686d115c0 100644
@@ -40,7 +40,7 @@ config AX25
 	  radio as well as information about how to configure an AX.25 port is
 	  contained in the AX25-HOWTO, available from
 	  <http://www.tldp.org/docs.html#howto>. You might also want to
-	  check out the file <file:Documentation/networking/ax25.txt> in the
+	  check out the file <file:Documentation/networking/ax25.rst> in the
 	  kernel source. More information about digital amateur radio in
 	  general is on the WWW at
 	  <http://www.tapr.org/>.
@@ -88,7 +88,7 @@ config NETROM
 	  users as well as information about how to configure an AX.25 port is
 	  contained in the Linux Ham Wiki, available from
 	  <http://www.linux-ax25.org>. You also might want to check out the
-	  file <file:Documentation/networking/ax25.txt>. More information about
+	  file <file:Documentation/networking/ax25.rst>. More information about
 	  digital amateur radio in general is on the WWW at
 	  <http://www.tapr.org/>.
 
@@ -107,7 +107,7 @@ config ROSE
 	  users as well as information about how to configure an AX.25 port is
 	  contained in the Linux Ham Wiki, available from
 	  <http://www.linux-ax25.org>.  You also might want to check out the
-	  file <file:Documentation/networking/ax25.txt>. More information about
+	  file <file:Documentation/networking/ax25.rst>. More information about
 	  digital amateur radio in general is on the WWW at
 	  <http://www.tapr.org/>.
 
Signature · 1 line
2.25.4
#8 lore raw

PATCH 8/38 docs: networking: convert baycom.txt to ReST

In reply to Mauro Carvalho Chehab

- add SPDX header;
- adjust titles and chapters, adding proper markups;
- mark code blocks and literals as such;
- mark tables as such;
- adjust identation, whitespaces and blank lines;
- add to networking/index.rst.

---
 .../networking/{baycom.txt => baycom.rst}     | 110 ++++++++++--------
 Documentation/networking/index.rst            |   1 +
 drivers/net/hamradio/Kconfig                  |   8 +-
 3 files changed, 68 insertions(+), 51 deletions(-)
 rename Documentation/networking/{baycom.txt => baycom.rst} (58%)
Documentation/networking/baycom.rst renamed from Documentation/networking/baycom.txt +63 -47
similarity index 58%
rename from Documentation/networking/baycom.txt
rename to Documentation/networking/baycom.rst
index 688f18fd4467..fe2d010f0e86 100644
@@ -1,26 +1,31 @@
-		    LINUX DRIVERS FOR BAYCOM MODEMS
+.. SPDX-License-Identifier: GPL-2.0
 
-       Thomas M. Sailer, HB9JNX/AE4WA, <[email protected]>
+===============================
+Linux Drivers for Baycom Modems
+===============================
 
-!!NEW!! (04/98) The drivers for the baycom modems have been split into
+Thomas M. Sailer, HB9JNX/AE4WA, <[email protected]>
+
+The drivers for the baycom modems have been split into
 separate drivers as they did not share any code, and the driver
 and device names have changed.
 
 This document describes the Linux Kernel Drivers for simple Baycom style
-amateur radio modems. 
+amateur radio modems.
 
 The following drivers are available:
+====================================
 
 baycom_ser_fdx:
   This driver supports the SER12 modems either full or half duplex.
-  Its baud rate may be changed via the `baud' module parameter,
+  Its baud rate may be changed via the ``baud`` module parameter,
   therefore it supports just about every bit bang modem on a
   serial port. Its devices are called bcsf0 through bcsf3.
   This is the recommended driver for SER12 type modems,
   however if you have a broken UART clone that does not have working
-  delta status bits, you may try baycom_ser_hdx. 
+  delta status bits, you may try baycom_ser_hdx.
 
-baycom_ser_hdx: 
+baycom_ser_hdx:
   This is an alternative driver for SER12 type modems.
   It only supports half duplex, and only 1200 baud. Its devices
   are called bcsh0 through bcsh3. Use this driver only if baycom_ser_fdx
@@ -37,45 +42,48 @@ baycom_epp:
 
 The following modems are supported:
 
-ser12:  This is a very simple 1200 baud AFSK modem. The modem consists only
-        of a modulator/demodulator chip, usually a TI TCM3105. The computer
-        is responsible for regenerating the receiver bit clock, as well as
-        for handling the HDLC protocol. The modem connects to a serial port,
-        hence the name. Since the serial port is not used as an async serial
-        port, the kernel driver for serial ports cannot be used, and this
-        driver only supports standard serial hardware (8250, 16450, 16550)
+======= ========================================================================
+ser12   This is a very simple 1200 baud AFSK modem. The modem consists only
+	of a modulator/demodulator chip, usually a TI TCM3105. The computer
+	is responsible for regenerating the receiver bit clock, as well as
+	for handling the HDLC protocol. The modem connects to a serial port,
+	hence the name. Since the serial port is not used as an async serial
+	port, the kernel driver for serial ports cannot be used, and this
+	driver only supports standard serial hardware (8250, 16450, 16550)
 
-par96:  This is a modem for 9600 baud FSK compatible to the G3RUH standard.
-        The modem does all the filtering and regenerates the receiver clock.
-        Data is transferred from and to the PC via a shift register.
-        The shift register is filled with 16 bits and an interrupt is signalled.
-        The PC then empties the shift register in a burst. This modem connects
-        to the parallel port, hence the name. The modem leaves the 
-        implementation of the HDLC protocol and the scrambler polynomial to
-        the PC.
+par96   This is a modem for 9600 baud FSK compatible to the G3RUH standard.
+	The modem does all the filtering and regenerates the receiver clock.
+	Data is transferred from and to the PC via a shift register.
+	The shift register is filled with 16 bits and an interrupt is signalled.
+	The PC then empties the shift register in a burst. This modem connects
+	to the parallel port, hence the name. The modem leaves the
+	implementation of the HDLC protocol and the scrambler polynomial to
+	the PC.
 
-picpar: This is a redesign of the par96 modem by Henning Rech, DF9IC. The modem
-        is protocol compatible to par96, but uses only three low power ICs
-        and can therefore be fed from the parallel port and does not require
-        an additional power supply. Furthermore, it incorporates a carrier
-        detect circuitry.
+picpar  This is a redesign of the par96 modem by Henning Rech, DF9IC. The modem
+	is protocol compatible to par96, but uses only three low power ICs
+	and can therefore be fed from the parallel port and does not require
+	an additional power supply. Furthermore, it incorporates a carrier
+	detect circuitry.
 
-EPP:    This is a high-speed modem adaptor that connects to an enhanced parallel port.
-        Its target audience is users working over a high speed hub (76.8kbit/s).
-
-eppfpga: This is a redesign of the EPP adaptor.
+EPP     This is a high-speed modem adaptor that connects to an enhanced parallel
+	port.
 
+	Its target audience is users working over a high speed hub (76.8kbit/s).
 
+eppfpga This is a redesign of the EPP adaptor.
+======= ========================================================================
 
 All of the above modems only support half duplex communications. However,
 the driver supports the KISS (see below) fullduplex command. It then simply
 starts to send as soon as there's a packet to transmit and does not care
 about DCD, i.e. it starts to send even if there's someone else on the channel.
-This command is required by some implementations of the DAMA channel 
+This command is required by some implementations of the DAMA channel
 access protocol.
 
 
 The Interface of the drivers
+============================
 
 Unlike previous drivers, these drivers are no longer character devices,
 but they are now true kernel network interfaces. Installation is therefore
@@ -88,20 +96,22 @@ me for WAMPES which allows attaching a kernel network interface directly.
 
 
 Configuring the driver
+======================
 
 Every time a driver is inserted into the kernel, it has to know which
 modems it should access at which ports. This can be done with the setbaycom
 utility. If you are only using one modem, you can also configure the
 driver from the insmod command line (or by means of an option line in
-/etc/modprobe.d/*.conf).
+``/etc/modprobe.d/*.conf``).
+
+Examples::
 
-Examples:
   modprobe baycom_ser_fdx mode="ser12*" iobase=0x3f8 irq=4
   sethdlc -i bcsf0 -p mode "ser12*" io 0x3f8 irq 4
 
 Both lines configure the first port to drive a ser12 modem at the first
-serial port (COM1 under DOS). The * in the mode parameter instructs the driver to use
-the software DCD algorithm (see below).
+serial port (COM1 under DOS). The * in the mode parameter instructs the driver
+to use the software DCD algorithm (see below)::
 
   insmod baycom_par mode="picpar" iobase=0x378
   sethdlc -i bcp0 -p mode "picpar" io 0x378
@@ -115,29 +125,33 @@ Note that both utilities interpret the values slightly differently.
 
 
 Hardware DCD versus Software DCD
+================================
 
 To avoid collisions on the air, the driver must know when the channel is
 busy. This is the task of the DCD circuitry/software. The driver may either
 utilise a software DCD algorithm (options=1) or use a DCD signal from
 the hardware (options=0).
 
-ser12:  if software DCD is utilised, the radio's squelch should always be
-        open. It is highly recommended to use the software DCD algorithm,
-        as it is much faster than most hardware squelch circuitry. The
-        disadvantage is a slightly higher load on the system.
+======= =================================================================
+ser12   if software DCD is utilised, the radio's squelch should always be
+	open. It is highly recommended to use the software DCD algorithm,
+	as it is much faster than most hardware squelch circuitry. The
+	disadvantage is a slightly higher load on the system.
 
-par96:  the software DCD algorithm for this type of modem is rather poor.
-        The modem simply does not provide enough information to implement
-        a reasonable DCD algorithm in software. Therefore, if your radio
-        feeds the DCD input of the PAR96 modem, the use of the hardware
-        DCD circuitry is recommended.
+par96   the software DCD algorithm for this type of modem is rather poor.
+	The modem simply does not provide enough information to implement
+	a reasonable DCD algorithm in software. Therefore, if your radio
+	feeds the DCD input of the PAR96 modem, the use of the hardware
+	DCD circuitry is recommended.
 
-picpar: the picpar modem features a builtin DCD hardware, which is highly
-        recommended.
+picpar  the picpar modem features a builtin DCD hardware, which is highly
+	recommended.
+======= =================================================================
 
 
 
 Compatibility with the rest of the Linux kernel
+===============================================
 
 The serial driver and the baycom serial drivers compete
 for the same hardware resources. Of course only one driver can access a given
@@ -154,5 +168,7 @@ The parallel port drivers (baycom_par, baycom_epp) now use the parport subsystem
 to arbitrate the ports between different client drivers.
 
 vy 73s de
+
 Tom Sailer, [email protected]
+
 hb9jnx @ hb9w.ampr.org
Documentation/networking/index.rst +1 -0
index 6a5858b27cf6..fbf845fbaff7 100644
@@ -43,6 +43,7 @@ Contents:
    arcnet
    atm
    ax25
+   baycom
 
 .. only::  subproject and html
 
drivers/net/hamradio/Kconfig +4 -4
index bf306fed04cc..fe409819b56d 100644
@@ -127,7 +127,7 @@ config BAYCOM_SER_FDX
 	  your serial interface chip. To configure the driver, use the sethdlc
 	  utility available in the standard ax25 utilities package. For
 	  information on the modems, see <http://www.baycom.de/> and
-	  <file:Documentation/networking/baycom.txt>.
+	  <file:Documentation/networking/baycom.rst>.
 
 	  To compile this driver as a module, choose M here: the module
 	  will be called baycom_ser_fdx.  This is recommended.
@@ -145,7 +145,7 @@ config BAYCOM_SER_HDX
 	  the driver, use the sethdlc utility available in the standard ax25
 	  utilities package. For information on the modems, see
 	  <http://www.baycom.de/> and
-	  <file:Documentation/networking/baycom.txt>.
+	  <file:Documentation/networking/baycom.rst>.
 
 	  To compile this driver as a module, choose M here: the module
 	  will be called baycom_ser_hdx.  This is recommended.
@@ -160,7 +160,7 @@ config BAYCOM_PAR
 	  par96 designs. To configure the driver, use the sethdlc utility
 	  available in the standard ax25 utilities package. For information on
 	  the modems, see <http://www.baycom.de/> and the file
-	  <file:Documentation/networking/baycom.txt>.
+	  <file:Documentation/networking/baycom.rst>.
 
 	  To compile this driver as a module, choose M here: the module
 	  will be called baycom_par.  This is recommended.
@@ -175,7 +175,7 @@ config BAYCOM_EPP
 	  designs. To configure the driver, use the sethdlc utility available
 	  in the standard ax25 utilities package. For information on the
 	  modems, see <http://www.baycom.de/> and the file
-	  <file:Documentation/networking/baycom.txt>.
+	  <file:Documentation/networking/baycom.rst>.
 
 	  To compile this driver as a module, choose M here: the module
 	  will be called baycom_epp.  This is recommended.
Signature · 1 line
2.25.4
#9 lore raw

PATCH 9/38 docs: networking: convert bonding.txt to ReST

In reply to Mauro Carvalho Chehab

- add SPDX header;
- adjust titles and chapters, adding proper markups;
- comment out text-only TOC from html/pdf output;
- mark code blocks and literals as such;
- mark tables as such;
- add notes markups;
- adjust identation, whitespaces and blank lines;
- add to networking/index.rst.

---
 .../networking/{bonding.txt => bonding.rst}   | 1275 +++++++++--------
 .../networking/device_drivers/intel/e100.rst  |    2 +-
 .../networking/device_drivers/intel/ixgb.rst  |    2 +-
 Documentation/networking/index.rst            |    1 +
 drivers/net/Kconfig                           |    2 +-
 5 files changed, 668 insertions(+), 614 deletions(-)
 rename Documentation/networking/{bonding.txt => bonding.rst} (75%)
Documentation/networking/bonding.rst renamed from Documentation/networking/bonding.txt +664 -611
similarity index 75%
rename from Documentation/networking/bonding.txt
rename to Documentation/networking/bonding.rst
index e3abfbd32f71..dd49f95d28d3 100644
@@ -1,10 +1,15 @@
+.. SPDX-License-Identifier: GPL-2.0
 
-		Linux Ethernet Bonding Driver HOWTO
+===================================
+Linux Ethernet Bonding Driver HOWTO
+===================================
 
-		Latest update: 27 April 2011
+Latest update: 27 April 2011
+
+Initial release: Thomas Davis <[email protected]>
+
+Corrections, HA extensions: 2000/10/03-15:
 
-Initial release : Thomas Davis <[email protected]>
-Corrections, HA extensions : 2000/10/03-15 :
   - Willy Tarreau <[email protected]>
   - Constantine Gavrilov <[email protected]>
   - Chad N. Tindel <ctindel@ieee dot org>
@@ -13,98 +18,98 @@ Corrections, HA extensions : 2000/10/03-15 :
 
 Reorganized and updated Feb 2005 by Jay Vosburgh
 Added Sysfs information: 2006/04/24
+
   - Mitch Williams <[email protected]>
 
 Introduction
 ============
 
-	The Linux bonding driver provides a method for aggregating
+The Linux bonding driver provides a method for aggregating
 multiple network interfaces into a single logical "bonded" interface.
 The behavior of the bonded interfaces depends upon the mode; generally
 speaking, modes provide either hot standby or load balancing services.
 Additionally, link integrity monitoring may be performed.
-	
-	The bonding driver originally came from Donald Becker's
+
+The bonding driver originally came from Donald Becker's
 beowulf patches for kernel 2.0. It has changed quite a bit since, and
 the original tools from extreme-linux and beowulf sites will not work
 with this version of the driver.
 
-	For new versions of the driver, updated userspace tools, and
+For new versions of the driver, updated userspace tools, and
 who to ask for help, please follow the links at the end of this file.
 
-Table of Contents
-=================
+.. Table of Contents
 
-1. Bonding Driver Installation
+   1. Bonding Driver Installation
 
-2. Bonding Driver Options
+   2. Bonding Driver Options
 
-3. Configuring Bonding Devices
-3.1	Configuration with Sysconfig Support
-3.1.1		Using DHCP with Sysconfig
-3.1.2		Configuring Multiple Bonds with Sysconfig
-3.2	Configuration with Initscripts Support
-3.2.1		Using DHCP with Initscripts
-3.2.2		Configuring Multiple Bonds with Initscripts
-3.3	Configuring Bonding Manually with Ifenslave
-3.3.1		Configuring Multiple Bonds Manually
-3.4	Configuring Bonding Manually via Sysfs
-3.5	Configuration with Interfaces Support
-3.6	Overriding Configuration for Special Cases
-3.7 Configuring LACP for 802.3ad mode in a more secure way
+   3. Configuring Bonding Devices
+   3.1	Configuration with Sysconfig Support
+   3.1.1		Using DHCP with Sysconfig
+   3.1.2		Configuring Multiple Bonds with Sysconfig
+   3.2	Configuration with Initscripts Support
+   3.2.1		Using DHCP with Initscripts
+   3.2.2		Configuring Multiple Bonds with Initscripts
+   3.3	Configuring Bonding Manually with Ifenslave
+   3.3.1		Configuring Multiple Bonds Manually
+   3.4	Configuring Bonding Manually via Sysfs
+   3.5	Configuration with Interfaces Support
+   3.6	Overriding Configuration for Special Cases
+   3.7 Configuring LACP for 802.3ad mode in a more secure way
 
-4. Querying Bonding Configuration
-4.1	Bonding Configuration
-4.2	Network Configuration
+   4. Querying Bonding Configuration
+   4.1	Bonding Configuration
+   4.2	Network Configuration
 
-5. Switch Configuration
+   5. Switch Configuration
 
-6. 802.1q VLAN Support
+   6. 802.1q VLAN Support
 
-7. Link Monitoring
-7.1	ARP Monitor Operation
-7.2	Configuring Multiple ARP Targets
-7.3	MII Monitor Operation
+   7. Link Monitoring
+   7.1	ARP Monitor Operation
+   7.2	Configuring Multiple ARP Targets
+   7.3	MII Monitor Operation
 
-8. Potential Trouble Sources
-8.1	Adventures in Routing
-8.2	Ethernet Device Renaming
-8.3	Painfully Slow Or No Failed Link Detection By Miimon
+   8. Potential Trouble Sources
+   8.1	Adventures in Routing
+   8.2	Ethernet Device Renaming
+   8.3	Painfully Slow Or No Failed Link Detection By Miimon
 
-9. SNMP agents
+   9. SNMP agents
 
-10. Promiscuous mode
+   10. Promiscuous mode
 
-11. Configuring Bonding for High Availability
-11.1	High Availability in a Single Switch Topology
-11.2	High Availability in a Multiple Switch Topology
-11.2.1		HA Bonding Mode Selection for Multiple Switch Topology
-11.2.2		HA Link Monitoring for Multiple Switch Topology
+   11. Configuring Bonding for High Availability
+   11.1	High Availability in a Single Switch Topology
+   11.2	High Availability in a Multiple Switch Topology
+   11.2.1		HA Bonding Mode Selection for Multiple Switch Topology
+   11.2.2		HA Link Monitoring for Multiple Switch Topology
 
-12. Configuring Bonding for Maximum Throughput
-12.1	Maximum Throughput in a Single Switch Topology
-12.1.1		MT Bonding Mode Selection for Single Switch Topology
-12.1.2		MT Link Monitoring for Single Switch Topology
-12.2	Maximum Throughput in a Multiple Switch Topology
-12.2.1		MT Bonding Mode Selection for Multiple Switch Topology
-12.2.2		MT Link Monitoring for Multiple Switch Topology
+   12. Configuring Bonding for Maximum Throughput
+   12.1	Maximum Throughput in a Single Switch Topology
+   12.1.1		MT Bonding Mode Selection for Single Switch Topology
+   12.1.2		MT Link Monitoring for Single Switch Topology
+   12.2	Maximum Throughput in a Multiple Switch Topology
+   12.2.1		MT Bonding Mode Selection for Multiple Switch Topology
+   12.2.2		MT Link Monitoring for Multiple Switch Topology
 
-13. Switch Behavior Issues
-13.1	Link Establishment and Failover Delays
-13.2	Duplicated Incoming Packets
+   13. Switch Behavior Issues
+   13.1	Link Establishment and Failover Delays
+   13.2	Duplicated Incoming Packets
 
-14. Hardware Specific Considerations
-14.1	IBM BladeCenter
+   14. Hardware Specific Considerations
+   14.1	IBM BladeCenter
 
-15. Frequently Asked Questions
+   15. Frequently Asked Questions
 
-16. Resources and Links
+   16. Resources and Links
 
 
 1. Bonding Driver Installation
 ==============================
 
-	Most popular distro kernels ship with the bonding driver
+Most popular distro kernels ship with the bonding driver
 already available as a module. If your distro does not, or you
 have need to compile bonding from source (e.g., configuring and
 installing a mainline kernel from kernel.org), you'll need to perform
@@ -113,54 +118,54 @@ the following steps:
 1.1 Configure and build the kernel with bonding
 -----------------------------------------------
 
-	The current version of the bonding driver is available in the
+The current version of the bonding driver is available in the
 drivers/net/bonding subdirectory of the most recent kernel source
 (which is available on http://kernel.org).  Most users "rolling their
 own" will want to use the most recent kernel from kernel.org.
 
-	Configure kernel with "make menuconfig" (or "make xconfig" or
+Configure kernel with "make menuconfig" (or "make xconfig" or
 "make config"), then select "Bonding driver support" in the "Network
 device support" section.  It is recommended that you configure the
 driver as module since it is currently the only way to pass parameters
 to the driver or configure more than one bonding device.
 
-	Build and install the new kernel and modules.
+Build and install the new kernel and modules.
 
 1.2 Bonding Control Utility
--------------------------------------
+---------------------------
 
-	 It is recommended to configure bonding via iproute2 (netlink)
+It is recommended to configure bonding via iproute2 (netlink)
 or sysfs, the old ifenslave control utility is obsolete.
 
 2. Bonding Driver Options
 =========================
 
-	Options for the bonding driver are supplied as parameters to the
+Options for the bonding driver are supplied as parameters to the
 bonding module at load time, or are specified via sysfs.
 
-	Module options may be given as command line arguments to the
+Module options may be given as command line arguments to the
 insmod or modprobe command, but are usually specified in either the
-/etc/modprobe.d/*.conf configuration files, or in a distro-specific
+``/etc/modprobe.d/*.conf`` configuration files, or in a distro-specific
 configuration file (some of which are detailed in the next section).
 
-	Details on bonding support for sysfs is provided in the
+Details on bonding support for sysfs is provided in the
 "Configuring Bonding Manually via Sysfs" section, below.
 
-	The available bonding driver parameters are listed below. If a
+The available bonding driver parameters are listed below. If a
 parameter is not specified the default value is used.  When initially
 configuring a bond, it is recommended "tail -f /var/log/messages" be
 run in a separate window to watch for bonding driver error messages.
 
-	It is critical that either the miimon or arp_interval and
+It is critical that either the miimon or arp_interval and
 arp_ip_target parameters be specified, otherwise serious network
 degradation will occur during link failures.  Very few devices do not
 support at least miimon, so there is really no reason not to use it.
 
-	Options with textual values will accept either the text name
+Options with textual values will accept either the text name
 or, for backwards compatibility, the option value.  E.g.,
 "mode=802.3ad" and "mode=4" set the same mode.
 
-	The parameters are as follows:
+The parameters are as follows:
 
 active_slave
 
@@ -246,10 +251,13 @@ ad_user_port_key
 
 	In an AD system, the port-key has three parts as shown below -
 
+	   =====  ============
 	   Bits   Use
+	   =====  ============
 	   00     Duplex
 	   01-05  Speed
 	   06-15  User-defined
+	   =====  ============
 
 	This defines the upper 10 bits of the port key. The values can be
 	from 0 - 1023. If not given, the system defaults to 0.
@@ -699,7 +707,7 @@ mode
 		swapped with the new curr_active_slave that was
 		chosen.
 
-num_grat_arp
+num_grat_arp,
 num_unsol_na
 
 	Specify the number of peer notifications (gratuitous ARPs and
@@ -729,13 +737,13 @@ packets_per_slave
 
 peer_notif_delay
 
-        Specify the delay, in milliseconds, between each peer
-        notification (gratuitous ARP and unsolicited IPv6 Neighbor
-        Advertisement) when they are issued after a failover event.
-        This delay should be a multiple of the link monitor interval
-        (arp_interval or miimon, whichever is active). The default
-        value is 0 which means to match the value of the link monitor
-        interval.
+	Specify the delay, in milliseconds, between each peer
+	notification (gratuitous ARP and unsolicited IPv6 Neighbor
+	Advertisement) when they are issued after a failover event.
+	This delay should be a multiple of the link monitor interval
+	(arp_interval or miimon, whichever is active). The default
+	value is 0 which means to match the value of the link monitor
+	interval.
 
 primary
 
@@ -977,88 +985,88 @@ lp_interval
 3. Configuring Bonding Devices
 ==============================
 
-	You can configure bonding using either your distro's network
+You can configure bonding using either your distro's network
 initialization scripts, or manually using either iproute2 or the
 sysfs interface.  Distros generally use one of three packages for the
 network initialization scripts: initscripts, sysconfig or interfaces.
 Recent versions of these packages have support for bonding, while older
 versions do not.
 
-	We will first describe the options for configuring bonding for
+We will first describe the options for configuring bonding for
 distros using versions of initscripts, sysconfig and interfaces with full
 or partial support for bonding, then provide information on enabling
 bonding without support from the network initialization scripts (i.e.,
 older versions of initscripts or sysconfig).
 
-	If you're unsure whether your distro uses sysconfig,
+If you're unsure whether your distro uses sysconfig,
 initscripts or interfaces, or don't know if it's new enough, have no fear.
 Determining this is fairly straightforward.
 
-	First, look for a file called interfaces in /etc/network directory.
+First, look for a file called interfaces in /etc/network directory.
 If this file is present in your system, then your system use interfaces. See
 Configuration with Interfaces Support.
 
-	Else, issue the command:
+Else, issue the command::
 
-$ rpm -qf /sbin/ifup
+	$ rpm -qf /sbin/ifup
 
-	It will respond with a line of text starting with either
+It will respond with a line of text starting with either
 "initscripts" or "sysconfig," followed by some numbers.  This is the
 package that provides your network initialization scripts.
 
-	Next, to determine if your installation supports bonding,
-issue the command:
+Next, to determine if your installation supports bonding,
+issue the command::
 
-$ grep ifenslave /sbin/ifup
+    $ grep ifenslave /sbin/ifup
 
-	If this returns any matches, then your initscripts or
+If this returns any matches, then your initscripts or
 sysconfig has support for bonding.
 
 3.1 Configuration with Sysconfig Support
 ----------------------------------------
 
-	This section applies to distros using a version of sysconfig
+This section applies to distros using a version of sysconfig
 with bonding support, for example, SuSE Linux Enterprise Server 9.
 
-	SuSE SLES 9's networking configuration system does support
+SuSE SLES 9's networking configuration system does support
 bonding, however, at this writing, the YaST system configuration
 front end does not provide any means to work with bonding devices.
 Bonding devices can be managed by hand, however, as follows.
 
-	First, if they have not already been configured, configure the
+First, if they have not already been configured, configure the
 slave devices.  On SLES 9, this is most easily done by running the
 yast2 sysconfig configuration utility.  The goal is for to create an
 ifcfg-id file for each slave device.  The simplest way to accomplish
 this is to configure the devices for DHCP (this is only to get the
 file ifcfg-id file created; see below for some issues with DHCP).  The
-name of the configuration file for each device will be of the form:
+name of the configuration file for each device will be of the form::
 
-ifcfg-id-xx:xx:xx:xx:xx:xx
+    ifcfg-id-xx:xx:xx:xx:xx:xx
 
-	Where the "xx" portion will be replaced with the digits from
+Where the "xx" portion will be replaced with the digits from
 the device's permanent MAC address.
 
-	Once the set of ifcfg-id-xx:xx:xx:xx:xx:xx files has been
+Once the set of ifcfg-id-xx:xx:xx:xx:xx:xx files has been
 created, it is necessary to edit the configuration files for the slave
 devices (the MAC addresses correspond to those of the slave devices).
 Before editing, the file will contain multiple lines, and will look
-something like this:
+something like this::
 
-BOOTPROTO='dhcp'
-STARTMODE='on'
-USERCTL='no'
-UNIQUE='XNzu.WeZGOGF+4wE'
-_nm_name='bus-pci-0001:61:01.0'
+	BOOTPROTO='dhcp'
+	STARTMODE='on'
+	USERCTL='no'
+	UNIQUE='XNzu.WeZGOGF+4wE'
+	_nm_name='bus-pci-0001:61:01.0'
 
-	Change the BOOTPROTO and STARTMODE lines to the following:
+Change the BOOTPROTO and STARTMODE lines to the following::
 
-BOOTPROTO='none'
-STARTMODE='off'
+	BOOTPROTO='none'
+	STARTMODE='off'
 
-	Do not alter the UNIQUE or _nm_name lines.  Remove any other
+Do not alter the UNIQUE or _nm_name lines.  Remove any other
 lines (USERCTL, etc).
 
-	Once the ifcfg-id-xx:xx:xx:xx:xx:xx files have been modified,
+Once the ifcfg-id-xx:xx:xx:xx:xx:xx files have been modified,
 it's time to create the configuration file for the bonding device
 itself.  This file is named ifcfg-bondX, where X is the number of the
 bonding device to create, starting at 0.  The first such file is
@@ -1066,49 +1074,52 @@ ifcfg-bond0, the second is ifcfg-bond1, and so on.  The sysconfig
 network configuration system will correctly start multiple instances
 of bonding.
 
-	The contents of the ifcfg-bondX file is as follows:
+The contents of the ifcfg-bondX file is as follows::
 
-BOOTPROTO="static"
-BROADCAST="10.0.2.255"
-IPADDR="10.0.2.10"
-NETMASK="255.255.0.0"
-NETWORK="10.0.2.0"
-REMOTE_IPADDR=""
-STARTMODE="onboot"
-BONDING_MASTER="yes"
-BONDING_MODULE_OPTS="mode=active-backup miimon=100"
-BONDING_SLAVE0="eth0"
-BONDING_SLAVE1="bus-pci-0000:06:08.1"
+	BOOTPROTO="static"
+	BROADCAST="10.0.2.255"
+	IPADDR="10.0.2.10"
+	NETMASK="255.255.0.0"
+	NETWORK="10.0.2.0"
+	REMOTE_IPADDR=""
+	STARTMODE="onboot"
+	BONDING_MASTER="yes"
+	BONDING_MODULE_OPTS="mode=active-backup miimon=100"
+	BONDING_SLAVE0="eth0"
+	BONDING_SLAVE1="bus-pci-0000:06:08.1"
 
-	Replace the sample BROADCAST, IPADDR, NETMASK and NETWORK
+Replace the sample BROADCAST, IPADDR, NETMASK and NETWORK
 values with the appropriate values for your network.
 
-	The STARTMODE specifies when the device is brought online.
+The STARTMODE specifies when the device is brought online.
 The possible values are:
 
-	onboot:	 The device is started at boot time.  If you're not
+	======== ======================================================
+	onboot	 The device is started at boot time.  If you're not
 		 sure, this is probably what you want.
 
-	manual:	 The device is started only when ifup is called
+	manual	 The device is started only when ifup is called
 		 manually.  Bonding devices may be configured this
 		 way if you do not wish them to start automatically
 		 at boot for some reason.
 
-	hotplug: The device is started by a hotplug event.  This is not
+	hotplug  The device is started by a hotplug event.  This is not
 		 a valid choice for a bonding device.
 
-	off or ignore: The device configuration is ignored.
+	off or   The device configuration is ignored.
+	ignore
+	======== ======================================================
 
-	The line BONDING_MASTER='yes' indicates that the device is a
+The line BONDING_MASTER='yes' indicates that the device is a
 bonding master device.  The only useful value is "yes."
 
-	The contents of BONDING_MODULE_OPTS are supplied to the
+The contents of BONDING_MODULE_OPTS are supplied to the
 instance of the bonding module for this device.  Specify the options
 for the bonding mode, link monitoring, and so on here.  Do not include
 the max_bonds bonding parameter; this will confuse the configuration
 system if you have multiple bonding devices.
 
-	Finally, supply one BONDING_SLAVEn="slave device" for each
+Finally, supply one BONDING_SLAVEn="slave device" for each
 slave.  where "n" is an increasing value, one for each slave.  The
 "slave device" is either an interface name, e.g., "eth0", or a device
 specifier for the network device.  The interface name is easier to
@@ -1120,34 +1131,34 @@ changes (for example, it is moved from one PCI slot to another).  The
 example above uses one of each type for demonstration purposes; most
 configurations will choose one or the other for all slave devices.
 
-	When all configuration files have been modified or created,
+When all configuration files have been modified or created,
 networking must be restarted for the configuration changes to take
-effect.  This can be accomplished via the following:
+effect.  This can be accomplished via the following::
 
-# /etc/init.d/network restart
+	# /etc/init.d/network restart
 
-	Note that the network control script (/sbin/ifdown) will
+Note that the network control script (/sbin/ifdown) will
 remove the bonding module as part of the network shutdown processing,
 so it is not necessary to remove the module by hand if, e.g., the
 module parameters have changed.
 
-	Also, at this writing, YaST/YaST2 will not manage bonding
+Also, at this writing, YaST/YaST2 will not manage bonding
 devices (they do not show bonding interfaces on its list of network
 devices).  It is necessary to edit the configuration file by hand to
 change the bonding configuration.
 
-	Additional general options and details of the ifcfg file
-format can be found in an example ifcfg template file:
+Additional general options and details of the ifcfg file
+format can be found in an example ifcfg template file::
 
-/etc/sysconfig/network/ifcfg.template
+	/etc/sysconfig/network/ifcfg.template
 
-	Note that the template does not document the various BONDING_
+Note that the template does not document the various ``BONDING_*``
 settings described above, but does describe many of the other options.
 
 3.1.1 Using DHCP with Sysconfig
 -------------------------------
 
-	Under sysconfig, configuring a device with BOOTPROTO='dhcp'
+Under sysconfig, configuring a device with BOOTPROTO='dhcp'
 will cause it to query DHCP for its IP address information.  At this
 writing, this does not function for bonding devices; the scripts
 attempt to obtain the device address from DHCP prior to adding any of
@@ -1157,7 +1168,7 @@ sent to the network.
 3.1.2 Configuring Multiple Bonds with Sysconfig
 -----------------------------------------------
 
-	The sysconfig network initialization system is capable of
+The sysconfig network initialization system is capable of
 handling multiple bonding devices.  All that is necessary is for each
 bonding instance to have an appropriately configured ifcfg-bondX file
 (as described above).  Do not specify the "max_bonds" parameter to any
@@ -1165,14 +1176,14 @@ instance of bonding, as this will confuse sysconfig.  If you require
 multiple bonding devices with identical parameters, create multiple
 ifcfg-bondX files.
 
-	Because the sysconfig scripts supply the bonding module
+Because the sysconfig scripts supply the bonding module
 options in the ifcfg-bondX file, it is not necessary to add them to
-the system /etc/modules.d/*.conf configuration files.
+the system ``/etc/modules.d/*.conf`` configuration files.
 
 3.2 Configuration with Initscripts Support
 ------------------------------------------
 
-	This section applies to distros using a recent version of
+This section applies to distros using a recent version of
 initscripts with bonding support, for example, Red Hat Enterprise Linux
 version 3 or later, Fedora, etc.  On these systems, the network
 initialization scripts have knowledge of bonding, and can be configured to
@@ -1180,7 +1191,7 @@ control bonding devices.  Note that older versions of the initscripts
 package have lower levels of support for bonding; this will be noted where
 applicable.
 
-	These distros will not automatically load the network adapter
+These distros will not automatically load the network adapter
 driver unless the ethX device is configured with an IP address.
 Because of this constraint, users must manually configure a
 network-script file for all physical adapters that will be members of
@@ -1188,19 +1199,19 @@ a bondX link.  Network script files are located in the directory:
 
 /etc/sysconfig/network-scripts
 
-	The file name must be prefixed with "ifcfg-eth" and suffixed
+The file name must be prefixed with "ifcfg-eth" and suffixed
 with the adapter's physical adapter number.  For example, the script
 for eth0 would be named /etc/sysconfig/network-scripts/ifcfg-eth0.
-Place the following text in the file:
+Place the following text in the file::
 
-DEVICE=eth0
-USERCTL=no
-ONBOOT=yes
-MASTER=bond0
-SLAVE=yes
-BOOTPROTO=none
+	DEVICE=eth0
+	USERCTL=no
+	ONBOOT=yes
+	MASTER=bond0
+	SLAVE=yes
+	BOOTPROTO=none
 
-	The DEVICE= line will be different for every ethX device and
+The DEVICE= line will be different for every ethX device and
 must correspond with the name of the file, i.e., ifcfg-eth1 must have
 a device line of DEVICE=eth1.  The setting of the MASTER= line will
 also depend on the final bonding interface name chosen for your bond.
@@ -1208,69 +1219,70 @@ As with other network devices, these typically start at 0, and go up
 one for each device, i.e., the first bonding instance is bond0, the
 second is bond1, and so on.
 
-	Next, create a bond network script.  The file name for this
+Next, create a bond network script.  The file name for this
 script will be /etc/sysconfig/network-scripts/ifcfg-bondX where X is
 the number of the bond.  For bond0 the file is named "ifcfg-bond0",
 for bond1 it is named "ifcfg-bond1", and so on.  Within that file,
-place the following text:
+place the following text::
 
-DEVICE=bond0
-IPADDR=192.168.1.1
-NETMASK=255.255.255.0
-NETWORK=192.168.1.0
-BROADCAST=192.168.1.255
-ONBOOT=yes
-BOOTPROTO=none
-USERCTL=no
+	DEVICE=bond0
+	IPADDR=192.168.1.1
+	NETMASK=255.255.255.0
+	NETWORK=192.168.1.0
+	BROADCAST=192.168.1.255
+	ONBOOT=yes
+	BOOTPROTO=none
+	USERCTL=no
 
-	Be sure to change the networking specific lines (IPADDR,
+Be sure to change the networking specific lines (IPADDR,
 NETMASK, NETWORK and BROADCAST) to match your network configuration.
 
-	For later versions of initscripts, such as that found with Fedora
+For later versions of initscripts, such as that found with Fedora
 7 (or later) and Red Hat Enterprise Linux version 5 (or later), it is possible,
 and, indeed, preferable, to specify the bonding options in the ifcfg-bond0
-file, e.g. a line of the format:
+file, e.g. a line of the format::
 
-BONDING_OPTS="mode=active-backup arp_interval=60 arp_ip_target=192.168.1.254"
+  BONDING_OPTS="mode=active-backup arp_interval=60 arp_ip_target=192.168.1.254"
 
-	will configure the bond with the specified options.  The options
+will configure the bond with the specified options.  The options
 specified in BONDING_OPTS are identical to the bonding module parameters
 except for the arp_ip_target field when using versions of initscripts older
 than and 8.57 (Fedora 8) and 8.45.19 (Red Hat Enterprise Linux 5.2).  When
 using older versions each target should be included as a separate option and
 should be preceded by a '+' to indicate it should be added to the list of
-queried targets, e.g.,
+queried targets, e.g.,::
 
-	arp_ip_target=+192.168.1.1 arp_ip_target=+192.168.1.2
+    arp_ip_target=+192.168.1.1 arp_ip_target=+192.168.1.2
 
-	is the proper syntax to specify multiple targets.  When specifying
-options via BONDING_OPTS, it is not necessary to edit /etc/modprobe.d/*.conf.
+is the proper syntax to specify multiple targets.  When specifying
+options via BONDING_OPTS, it is not necessary to edit
+``/etc/modprobe.d/*.conf``.
 
-	For even older versions of initscripts that do not support
+For even older versions of initscripts that do not support
 BONDING_OPTS, it is necessary to edit /etc/modprobe.d/*.conf, depending upon
 your distro) to load the bonding module with your desired options when the
 bond0 interface is brought up.  The following lines in /etc/modprobe.d/*.conf
 will load the bonding module, and select its options:
 
-alias bond0 bonding
-options bond0 mode=balance-alb miimon=100
+	alias bond0 bonding
+	options bond0 mode=balance-alb miimon=100
 
-	Replace the sample parameters with the appropriate set of
+Replace the sample parameters with the appropriate set of
 options for your configuration.
 
-	Finally run "/etc/rc.d/init.d/network restart" as root.  This
+Finally run "/etc/rc.d/init.d/network restart" as root.  This
 will restart the networking subsystem and your bond link should be now
 up and running.
 
 3.2.1 Using DHCP with Initscripts
 ---------------------------------
 
-	Recent versions of initscripts (the versions supplied with Fedora
+Recent versions of initscripts (the versions supplied with Fedora
 Core 3 and Red Hat Enterprise Linux 4, or later versions, are reported to
 work) have support for assigning IP information to bonding devices via
 DHCP.
 
-	To configure bonding for DHCP, configure it as described
+To configure bonding for DHCP, configure it as described
 above, except replace the line "BOOTPROTO=none" with "BOOTPROTO=dhcp"
 and add a line consisting of "TYPE=Bonding".  Note that the TYPE value
 is case sensitive.
@@ -1278,7 +1290,7 @@ is case sensitive.
 3.2.2 Configuring Multiple Bonds with Initscripts
 -------------------------------------------------
 
-	Initscripts packages that are included with Fedora 7 and Red Hat
+Initscripts packages that are included with Fedora 7 and Red Hat
 Enterprise Linux 5 support multiple bonding interfaces by simply
 specifying the appropriate BONDING_OPTS= in ifcfg-bondX where X is the
 number of the bond.  This support requires sysfs support in the kernel,
@@ -1290,77 +1302,77 @@ below.
 3.3 Configuring Bonding Manually with iproute2
 -----------------------------------------------
 
-	This section applies to distros whose network initialization
+This section applies to distros whose network initialization
 scripts (the sysconfig or initscripts package) do not have specific
 knowledge of bonding.  One such distro is SuSE Linux Enterprise Server
 version 8.
 
-	The general method for these systems is to place the bonding
+The general method for these systems is to place the bonding
 module parameters into a config file in /etc/modprobe.d/ (as
 appropriate for the installed distro), then add modprobe and/or
 `ip link` commands to the system's global init script.  The name of
 the global init script differs; for sysconfig, it is
 /etc/init.d/boot.local and for initscripts it is /etc/rc.d/rc.local.
 
-	For example, if you wanted to make a simple bond of two e100
+For example, if you wanted to make a simple bond of two e100
 devices (presumed to be eth0 and eth1), and have it persist across
 reboots, edit the appropriate file (/etc/init.d/boot.local or
-/etc/rc.d/rc.local), and add the following:
+/etc/rc.d/rc.local), and add the following::
 
-modprobe bonding mode=balance-alb miimon=100
-modprobe e100
-ifconfig bond0 192.168.1.1 netmask 255.255.255.0 up
-ip link set eth0 master bond0
-ip link set eth1 master bond0
+	modprobe bonding mode=balance-alb miimon=100
+	modprobe e100
+	ifconfig bond0 192.168.1.1 netmask 255.255.255.0 up
+	ip link set eth0 master bond0
+	ip link set eth1 master bond0
 
-	Replace the example bonding module parameters and bond0
+Replace the example bonding module parameters and bond0
 network configuration (IP address, netmask, etc) with the appropriate
 values for your configuration.
 
-	Unfortunately, this method will not provide support for the
+Unfortunately, this method will not provide support for the
 ifup and ifdown scripts on the bond devices.  To reload the bonding
-configuration, it is necessary to run the initialization script, e.g.,
+configuration, it is necessary to run the initialization script, e.g.,::
 
-# /etc/init.d/boot.local
+	# /etc/init.d/boot.local
 
-	or
+or::
 
-# /etc/rc.d/rc.local
+	# /etc/rc.d/rc.local
 
-	It may be desirable in such a case to create a separate script
+It may be desirable in such a case to create a separate script
 which only initializes the bonding configuration, then call that
 separate script from within boot.local.  This allows for bonding to be
 enabled without re-running the entire global init script.
 
-	To shut down the bonding devices, it is necessary to first
+To shut down the bonding devices, it is necessary to first
 mark the bonding device itself as being down, then remove the
 appropriate device driver modules.  For our example above, you can do
-the following:
+the following::
 
-# ifconfig bond0 down
-# rmmod bonding
-# rmmod e100
+	# ifconfig bond0 down
+	# rmmod bonding
+	# rmmod e100
 
-	Again, for convenience, it may be desirable to create a script
+Again, for convenience, it may be desirable to create a script
 with these commands.
 
 
 3.3.1 Configuring Multiple Bonds Manually
 -----------------------------------------
 
-	This section contains information on configuring multiple
+This section contains information on configuring multiple
 bonding devices with differing options for those systems whose network
 initialization scripts lack support for configuring multiple bonds.
 
-	If you require multiple bonding devices, but all with the same
+If you require multiple bonding devices, but all with the same
 options, you may wish to use the "max_bonds" module parameter,
 documented above.
 
-	To create multiple bonding devices with differing options, it is
+To create multiple bonding devices with differing options, it is
 preferable to use bonding parameters exported by sysfs, documented in the
 section below.
 
-	For versions of bonding without sysfs support, the only means to
+For versions of bonding without sysfs support, the only means to
 provide multiple instances of bonding with differing options is to load
 the bonding driver multiple times.  Note that current versions of the
 sysconfig network initialization scripts handle this automatically; if
@@ -1368,35 +1380,35 @@ your distro uses these scripts, no special action is needed.  See the
 section Configuring Bonding Devices, above, if you're not sure about your
 network initialization scripts.
 
-	To load multiple instances of the module, it is necessary to
+To load multiple instances of the module, it is necessary to
 specify a different name for each instance (the module loading system
 requires that every loaded module, even multiple instances of the same
 module, have a unique name).  This is accomplished by supplying multiple
-sets of bonding options in /etc/modprobe.d/*.conf, for example:
+sets of bonding options in ``/etc/modprobe.d/*.conf``, for example::
 
-alias bond0 bonding
-options bond0 -o bond0 mode=balance-rr miimon=100
+	alias bond0 bonding
+	options bond0 -o bond0 mode=balance-rr miimon=100
 
-alias bond1 bonding
-options bond1 -o bond1 mode=balance-alb miimon=50
+	alias bond1 bonding
+	options bond1 -o bond1 mode=balance-alb miimon=50
 
-	will load the bonding module two times.  The first instance is
+will load the bonding module two times.  The first instance is
 named "bond0" and creates the bond0 device in balance-rr mode with an
 miimon of 100.  The second instance is named "bond1" and creates the
 bond1 device in balance-alb mode with an miimon of 50.
 
-	In some circumstances (typically with older distributions),
+In some circumstances (typically with older distributions),
 the above does not work, and the second bonding instance never sees
 its options.  In that case, the second options line can be substituted
-as follows:
+as follows::
 
-install bond1 /sbin/modprobe --ignore-install bonding -o bond1 \
-	mode=balance-alb miimon=50
+	install bond1 /sbin/modprobe --ignore-install bonding -o bond1 \
+				     mode=balance-alb miimon=50
 
-	This may be repeated any number of times, specifying a new and
+This may be repeated any number of times, specifying a new and
 unique name in place of bond1 for each subsequent instance.
 
-	It has been observed that some Red Hat supplied kernels are unable
+It has been observed that some Red Hat supplied kernels are unable
 to rename modules at load time (the "-o bond1" part).  Attempts to pass
 that option to modprobe will produce an "Operation not permitted" error.
 This has been reported on some Fedora Core kernels, and has been seen on
@@ -1407,18 +1419,18 @@ kernels, and also lack sysfs support).
 3.4 Configuring Bonding Manually via Sysfs
 ------------------------------------------
 
-	Starting with version 3.0.0, Channel Bonding may be configured
+Starting with version 3.0.0, Channel Bonding may be configured
 via the sysfs interface.  This interface allows dynamic configuration
 of all bonds in the system without unloading the module.  It also
 allows for adding and removing bonds at runtime.  Ifenslave is no
 longer required, though it is still supported.
 
-	Use of the sysfs interface allows you to use multiple bonds
+Use of the sysfs interface allows you to use multiple bonds
 with different configurations without having to reload the module.
 It also allows you to use multiple, differently configured bonds when
 bonding is compiled into the kernel.
 
-	You must have the sysfs filesystem mounted to configure
+You must have the sysfs filesystem mounted to configure
 bonding this way.  The examples in this document assume that you
 are using the standard mount point for sysfs, e.g. /sys.  If your
 sysfs filesystem is mounted elsewhere, you will need to adjust the
@@ -1426,38 +1438,45 @@ example paths accordingly.
 
 Creating and Destroying Bonds
 -----------------------------
-To add a new bond foo:
-# echo +foo > /sys/class/net/bonding_masters
+To add a new bond foo::
 
-To remove an existing bond bar:
-# echo -bar > /sys/class/net/bonding_masters
+	# echo +foo > /sys/class/net/bonding_masters
 
-To show all existing bonds:
-# cat /sys/class/net/bonding_masters
+To remove an existing bond bar::
 
-NOTE: due to 4K size limitation of sysfs files, this list may be
-truncated if you have more than a few hundred bonds.  This is unlikely
-to occur under normal operating conditions.
+	# echo -bar > /sys/class/net/bonding_masters
+
+To show all existing bonds::
+
+	# cat /sys/class/net/bonding_masters
+
+.. note::
+
+   due to 4K size limitation of sysfs files, this list may be
+   truncated if you have more than a few hundred bonds.  This is unlikely
+   to occur under normal operating conditions.
 
 Adding and Removing Slaves
 --------------------------
-	Interfaces may be enslaved to a bond using the file
+Interfaces may be enslaved to a bond using the file
 /sys/class/net/<bond>/bonding/slaves.  The semantics for this file
 are the same as for the bonding_masters file.
 
-To enslave interface eth0 to bond bond0:
-# ifconfig bond0 up
-# echo +eth0 > /sys/class/net/bond0/bonding/slaves
+To enslave interface eth0 to bond bond0::
 
-To free slave eth0 from bond bond0:
-# echo -eth0 > /sys/class/net/bond0/bonding/slaves
+	# ifconfig bond0 up
+	# echo +eth0 > /sys/class/net/bond0/bonding/slaves
 
-	When an interface is enslaved to a bond, symlinks between the
+To free slave eth0 from bond bond0::
+
+	# echo -eth0 > /sys/class/net/bond0/bonding/slaves
+
+When an interface is enslaved to a bond, symlinks between the
 two are created in the sysfs filesystem.  In this case, you would get
 /sys/class/net/bond0/slave_eth0 pointing to /sys/class/net/eth0, and
 /sys/class/net/eth0/master pointing to /sys/class/net/bond0.
 
-	This means that you can tell quickly whether or not an
+This means that you can tell quickly whether or not an
 interface is enslaved by looking for the master symlink.  Thus:
 # echo -eth0 > /sys/class/net/eth0/master/bonding/slaves
 will free eth0 from whatever bond it is enslaved to, regardless of
@@ -1465,127 +1484,143 @@ the name of the bond interface.
 
 Changing a Bond's Configuration
 -------------------------------
-	Each bond may be configured individually by manipulating the
+Each bond may be configured individually by manipulating the
 files located in /sys/class/net/<bond name>/bonding
 
-	The names of these files correspond directly with the command-
+The names of these files correspond directly with the command-
 line parameters described elsewhere in this file, and, with the
 exception of arp_ip_target, they accept the same values.  To see the
 current setting, simply cat the appropriate file.
 
-	A few examples will be given here; for specific usage
+A few examples will be given here; for specific usage
 guidelines for each parameter, see the appropriate section in this
 document.
 
-To configure bond0 for balance-alb mode:
-# ifconfig bond0 down
-# echo 6 > /sys/class/net/bond0/bonding/mode
- - or -
-# echo balance-alb > /sys/class/net/bond0/bonding/mode
-	NOTE: The bond interface must be down before the mode can be
-changed.
-
-To enable MII monitoring on bond0 with a 1 second interval:
-# echo 1000 > /sys/class/net/bond0/bonding/miimon
-	NOTE: If ARP monitoring is enabled, it will disabled when MII
-monitoring is enabled, and vice-versa.
-
-To add ARP targets:
-# echo +192.168.0.100 > /sys/class/net/bond0/bonding/arp_ip_target
-# echo +192.168.0.101 > /sys/class/net/bond0/bonding/arp_ip_target
-	NOTE:  up to 16 target addresses may be specified.
-
-To remove an ARP target:
-# echo -192.168.0.100 > /sys/class/net/bond0/bonding/arp_ip_target
-
-To configure the interval between learning packet transmits:
-# echo 12 > /sys/class/net/bond0/bonding/lp_interval
-	NOTE: the lp_interval is the number of seconds between instances where
-the bonding driver sends learning packets to each slaves peer switch.  The
-default interval is 1 second.
+To configure bond0 for balance-alb mode::
+
+	# ifconfig bond0 down
+	# echo 6 > /sys/class/net/bond0/bonding/mode
+	- or -
+	# echo balance-alb > /sys/class/net/bond0/bonding/mode
+
+.. note::
+
+   The bond interface must be down before the mode can be changed.
+
+To enable MII monitoring on bond0 with a 1 second interval::
+
+	# echo 1000 > /sys/class/net/bond0/bonding/miimon
+
+.. note::
+
+   If ARP monitoring is enabled, it will disabled when MII
+   monitoring is enabled, and vice-versa.
+
+To add ARP targets::
+
+	# echo +192.168.0.100 > /sys/class/net/bond0/bonding/arp_ip_target
+	# echo +192.168.0.101 > /sys/class/net/bond0/bonding/arp_ip_target
+
+.. note::
+
+   up to 16 target addresses may be specified.
+
+To remove an ARP target::
+
+	# echo -192.168.0.100 > /sys/class/net/bond0/bonding/arp_ip_target
+
+To configure the interval between learning packet transmits::
+
+	# echo 12 > /sys/class/net/bond0/bonding/lp_interval
+
+.. note::
+
+   the lp_interval is the number of seconds between instances where
+   the bonding driver sends learning packets to each slaves peer switch.  The
+   default interval is 1 second.
 
 Example Configuration
 ---------------------
-	We begin with the same example that is shown in section 3.3,
+We begin with the same example that is shown in section 3.3,
 executed with sysfs, and without using ifenslave.
 
-	To make a simple bond of two e100 devices (presumed to be eth0
+To make a simple bond of two e100 devices (presumed to be eth0
 and eth1), and have it persist across reboots, edit the appropriate
 file (/etc/init.d/boot.local or /etc/rc.d/rc.local), and add the
-following:
+following::
 
-modprobe bonding
-modprobe e100
-echo balance-alb > /sys/class/net/bond0/bonding/mode
-ifconfig bond0 192.168.1.1 netmask 255.255.255.0 up
-echo 100 > /sys/class/net/bond0/bonding/miimon
-echo +eth0 > /sys/class/net/bond0/bonding/slaves
-echo +eth1 > /sys/class/net/bond0/bonding/slaves
+	modprobe bonding
+	modprobe e100
+	echo balance-alb > /sys/class/net/bond0/bonding/mode
+	ifconfig bond0 192.168.1.1 netmask 255.255.255.0 up
+	echo 100 > /sys/class/net/bond0/bonding/miimon
+	echo +eth0 > /sys/class/net/bond0/bonding/slaves
+	echo +eth1 > /sys/class/net/bond0/bonding/slaves
 
-	To add a second bond, with two e1000 interfaces in
+To add a second bond, with two e1000 interfaces in
 active-backup mode, using ARP monitoring, add the following lines to
-your init script:
+your init script::
 
-modprobe e1000
-echo +bond1 > /sys/class/net/bonding_masters
-echo active-backup > /sys/class/net/bond1/bonding/mode
-ifconfig bond1 192.168.2.1 netmask 255.255.255.0 up
-echo +192.168.2.100 /sys/class/net/bond1/bonding/arp_ip_target
-echo 2000 > /sys/class/net/bond1/bonding/arp_interval
-echo +eth2 > /sys/class/net/bond1/bonding/slaves
-echo +eth3 > /sys/class/net/bond1/bonding/slaves
+	modprobe e1000
+	echo +bond1 > /sys/class/net/bonding_masters
+	echo active-backup > /sys/class/net/bond1/bonding/mode
+	ifconfig bond1 192.168.2.1 netmask 255.255.255.0 up
+	echo +192.168.2.100 /sys/class/net/bond1/bonding/arp_ip_target
+	echo 2000 > /sys/class/net/bond1/bonding/arp_interval
+	echo +eth2 > /sys/class/net/bond1/bonding/slaves
+	echo +eth3 > /sys/class/net/bond1/bonding/slaves
 
 3.5 Configuration with Interfaces Support
 -----------------------------------------
 
-        This section applies to distros which use /etc/network/interfaces file
+This section applies to distros which use /etc/network/interfaces file
 to describe network interface configuration, most notably Debian and it's
 derivatives.
 
-	The ifup and ifdown commands on Debian don't support bonding out of
+The ifup and ifdown commands on Debian don't support bonding out of
 the box. The ifenslave-2.6 package should be installed to provide bonding
-support.  Once installed, this package will provide bond-* options to be used
-into /etc/network/interfaces.
+support.  Once installed, this package will provide ``bond-*`` options
+to be used into /etc/network/interfaces.
 
-	Note that ifenslave-2.6 package will load the bonding module and use
+Note that ifenslave-2.6 package will load the bonding module and use
 the ifenslave command when appropriate.
 
 Example Configurations
 ----------------------
 
 In /etc/network/interfaces, the following stanza will configure bond0, in
-active-backup mode, with eth0 and eth1 as slaves.
+active-backup mode, with eth0 and eth1 as slaves::
 
-auto bond0
-iface bond0 inet dhcp
-	bond-slaves eth0 eth1
-	bond-mode active-backup
-	bond-miimon 100
-	bond-primary eth0 eth1
+	auto bond0
+	iface bond0 inet dhcp
+		bond-slaves eth0 eth1
+		bond-mode active-backup
+		bond-miimon 100
+		bond-primary eth0 eth1
 
 If the above configuration doesn't work, you might have a system using
 upstart for system startup. This is most notably true for recent
 Ubuntu versions. The following stanza in /etc/network/interfaces will
-produce the same result on those systems.
+produce the same result on those systems::
 
-auto bond0
-iface bond0 inet dhcp
-	bond-slaves none
-	bond-mode active-backup
-	bond-miimon 100
+	auto bond0
+	iface bond0 inet dhcp
+		bond-slaves none
+		bond-mode active-backup
+		bond-miimon 100
 
-auto eth0
-iface eth0 inet manual
-	bond-master bond0
-	bond-primary eth0 eth1
+	auto eth0
+	iface eth0 inet manual
+		bond-master bond0
+		bond-primary eth0 eth1
 
-auto eth1
-iface eth1 inet manual
-	bond-master bond0
-	bond-primary eth0 eth1
+	auto eth1
+	iface eth1 inet manual
+		bond-master bond0
+		bond-primary eth0 eth1
 
-For a full list of bond-* supported options in /etc/network/interfaces and some
-more advanced examples tailored to you particular distros, see the files in
+For a full list of ``bond-*`` supported options in /etc/network/interfaces and
+some more advanced examples tailored to you particular distros, see the files in
 /usr/share/doc/ifenslave-2.6.
 
 3.6 Overriding Configuration for Special Cases
@@ -1610,31 +1645,31 @@ tx_queues can be used to change this value.  There is no sysfs parameter
 available as the allocation is done at module init time.
 
 The output of the file /proc/net/bonding/bondX has changed so the output Queue
-ID is now printed for each slave:
+ID is now printed for each slave::
 
-Bonding Mode: fault-tolerance (active-backup)
-Primary Slave: None
-Currently Active Slave: eth0
-MII Status: up
-MII Polling Interval (ms): 0
-Up Delay (ms): 0
-Down Delay (ms): 0
+	Bonding Mode: fault-tolerance (active-backup)
+	Primary Slave: None
+	Currently Active Slave: eth0
+	MII Status: up
+	MII Polling Interval (ms): 0
+	Up Delay (ms): 0
+	Down Delay (ms): 0
 
-Slave Interface: eth0
-MII Status: up
-Link Failure Count: 0
-Permanent HW addr: 00:1a:a0:12:8f:cb
-Slave queue ID: 0
+	Slave Interface: eth0
+	MII Status: up
+	Link Failure Count: 0
+	Permanent HW addr: 00:1a:a0:12:8f:cb
+	Slave queue ID: 0
 
-Slave Interface: eth1
-MII Status: up
-Link Failure Count: 0
-Permanent HW addr: 00:1a:a0:12:8f:cc
-Slave queue ID: 2
+	Slave Interface: eth1
+	MII Status: up
+	Link Failure Count: 0
+	Permanent HW addr: 00:1a:a0:12:8f:cc
+	Slave queue ID: 2
 
-The queue_id for a slave can be set using the command:
+The queue_id for a slave can be set using the command::
 
-# echo "eth1:2" > /sys/class/net/bond0/bonding/queue_id
+	# echo "eth1:2" > /sys/class/net/bond0/bonding/queue_id
 
 Any interface that needs a queue_id set should set it with multiple calls
 like the one above until proper priorities are set for all interfaces.  On
@@ -1645,12 +1680,12 @@ These queue id's can be used in conjunction with the tc utility to configure
 a multiqueue qdisc and filters to bias certain traffic to transmit on certain
 slave devices.  For instance, say we wanted, in the above configuration to
 force all traffic bound to 192.168.1.100 to use eth1 in the bond as its output
-device. The following commands would accomplish this:
+device. The following commands would accomplish this::
 
-# tc qdisc add dev bond0 handle 1 root multiq
+	# tc qdisc add dev bond0 handle 1 root multiq
 
-# tc filter add dev bond0 protocol ip parent 1: prio 1 u32 match ip dst \
-	192.168.1.100 action skbedit queue_mapping 2
+	# tc filter add dev bond0 protocol ip parent 1: prio 1 u32 match ip \
+		dst 192.168.1.100 action skbedit queue_mapping 2
 
 These commands tell the kernel to attach a multiqueue queue discipline to the
 bond0 interface and filter traffic enqueued to it, such that packets with a dst
@@ -1663,7 +1698,7 @@ that normal output policy selection should take place.  One benefit to simply
 leaving the qid for a slave to 0 is the multiqueue awareness in the bonding
 driver that is now present.  This awareness allows tc filters to be placed on
 slave devices as well as bond devices and the bonding driver will simply act as
-a pass-through for selecting output queues on the slave device rather than 
+a pass-through for selecting output queues on the slave device rather than
 output port selection.
 
 This feature first appeared in bonding driver version 3.7.0 and support for
@@ -1689,31 +1724,31 @@ few bonding parameters:
    (a) ad_actor_system : You can set a random mac-address that can be used for
        these LACPDU exchanges. The value can not be either NULL or Multicast.
        Also it's preferable to set the local-admin bit. Following shell code
-       generates a random mac-address as described above.
+       generates a random mac-address as described above::
 
-       # sys_mac_addr=$(printf '%02x:%02x:%02x:%02x:%02x:%02x' \
-                                $(( (RANDOM & 0xFE) | 0x02 )) \
-                                $(( RANDOM & 0xFF )) \
-                                $(( RANDOM & 0xFF )) \
-                                $(( RANDOM & 0xFF )) \
-                                $(( RANDOM & 0xFF )) \
-                                $(( RANDOM & 0xFF )))
-       # echo $sys_mac_addr > /sys/class/net/bond0/bonding/ad_actor_system
+	      # sys_mac_addr=$(printf '%02x:%02x:%02x:%02x:%02x:%02x' \
+				       $(( (RANDOM & 0xFE) | 0x02 )) \
+				       $(( RANDOM & 0xFF )) \
+				       $(( RANDOM & 0xFF )) \
+				       $(( RANDOM & 0xFF )) \
+				       $(( RANDOM & 0xFF )) \
+				       $(( RANDOM & 0xFF )))
+	      # echo $sys_mac_addr > /sys/class/net/bond0/bonding/ad_actor_system
 
    (b) ad_actor_sys_prio : Randomize the system priority. The default value
        is 65535, but system can take the value from 1 - 65535. Following shell
-       code generates random priority and sets it.
+       code generates random priority and sets it::
 
-       # sys_prio=$(( 1 + RANDOM + RANDOM ))
-       # echo $sys_prio > /sys/class/net/bond0/bonding/ad_actor_sys_prio
+	    # sys_prio=$(( 1 + RANDOM + RANDOM ))
+	    # echo $sys_prio > /sys/class/net/bond0/bonding/ad_actor_sys_prio
 
    (c) ad_user_port_key : Use the user portion of the port-key. The default
        keeps this empty. These are the upper 10 bits of the port-key and value
        ranges from 0 - 1023. Following shell code generates these 10 bits and
-       sets it.
+       sets it::
 
-       # usr_port_key=$(( RANDOM & 0x3FF ))
-       # echo $usr_port_key > /sys/class/net/bond0/bonding/ad_user_port_key
+	    # usr_port_key=$(( RANDOM & 0x3FF ))
+	    # echo $usr_port_key > /sys/class/net/bond0/bonding/ad_user_port_key
 
 
 4 Querying Bonding Configuration
@@ -1722,81 +1757,81 @@ few bonding parameters:
 4.1 Bonding Configuration
 -------------------------
 
-	Each bonding device has a read-only file residing in the
+Each bonding device has a read-only file residing in the
 /proc/net/bonding directory.  The file contents include information
 about the bonding configuration, options and state of each slave.
 
-	For example, the contents of /proc/net/bonding/bond0 after the
+For example, the contents of /proc/net/bonding/bond0 after the
 driver is loaded with parameters of mode=0 and miimon=1000 is
-generally as follows:
+generally as follows::
 
 	Ethernet Channel Bonding Driver: 2.6.1 (October 29, 2004)
-        Bonding Mode: load balancing (round-robin)
-        Currently Active Slave: eth0
-        MII Status: up
-        MII Polling Interval (ms): 1000
-        Up Delay (ms): 0
-        Down Delay (ms): 0
+	Bonding Mode: load balancing (round-robin)
+	Currently Active Slave: eth0
+	MII Status: up
+	MII Polling Interval (ms): 1000
+	Up Delay (ms): 0
+	Down Delay (ms): 0
 
-        Slave Interface: eth1
-        MII Status: up
-        Link Failure Count: 1
+	Slave Interface: eth1
+	MII Status: up
+	Link Failure Count: 1
 
-        Slave Interface: eth0
-        MII Status: up
-        Link Failure Count: 1
+	Slave Interface: eth0
+	MII Status: up
+	Link Failure Count: 1
 
-	The precise format and contents will change depending upon the
+The precise format and contents will change depending upon the
 bonding configuration, state, and version of the bonding driver.
 
 4.2 Network configuration
 -------------------------
 
-	The network configuration can be inspected using the ifconfig
+The network configuration can be inspected using the ifconfig
 command.  Bonding devices will have the MASTER flag set; Bonding slave
 devices will have the SLAVE flag set.  The ifconfig output does not
 contain information on which slaves are associated with which masters.
 
-	In the example below, the bond0 interface is the master
+In the example below, the bond0 interface is the master
 (MASTER) while eth0 and eth1 are slaves (SLAVE). Notice all slaves of
 bond0 have the same MAC address (HWaddr) as bond0 for all modes except
-TLB and ALB that require a unique MAC address for each slave.
+TLB and ALB that require a unique MAC address for each slave::
 
-# /sbin/ifconfig
-bond0     Link encap:Ethernet  HWaddr 00:C0:F0:1F:37:B4
-          inet addr:XXX.XXX.XXX.YYY  Bcast:XXX.XXX.XXX.255  Mask:255.255.252.0
-          UP BROADCAST RUNNING MASTER MULTICAST  MTU:1500  Metric:1
-          RX packets:7224794 errors:0 dropped:0 overruns:0 frame:0
-          TX packets:3286647 errors:1 dropped:0 overruns:1 carrier:0
-          collisions:0 txqueuelen:0
+  # /sbin/ifconfig
+  bond0     Link encap:Ethernet  HWaddr 00:C0:F0:1F:37:B4
+	    inet addr:XXX.XXX.XXX.YYY  Bcast:XXX.XXX.XXX.255  Mask:255.255.252.0
+	    UP BROADCAST RUNNING MASTER MULTICAST  MTU:1500  Metric:1
+	    RX packets:7224794 errors:0 dropped:0 overruns:0 frame:0
+	    TX packets:3286647 errors:1 dropped:0 overruns:1 carrier:0
+	    collisions:0 txqueuelen:0
 
-eth0      Link encap:Ethernet  HWaddr 00:C0:F0:1F:37:B4
-          UP BROADCAST RUNNING SLAVE MULTICAST  MTU:1500  Metric:1
-          RX packets:3573025 errors:0 dropped:0 overruns:0 frame:0
-          TX packets:1643167 errors:1 dropped:0 overruns:1 carrier:0
-          collisions:0 txqueuelen:100
-          Interrupt:10 Base address:0x1080
+  eth0      Link encap:Ethernet  HWaddr 00:C0:F0:1F:37:B4
+	    UP BROADCAST RUNNING SLAVE MULTICAST  MTU:1500  Metric:1
+	    RX packets:3573025 errors:0 dropped:0 overruns:0 frame:0
+	    TX packets:1643167 errors:1 dropped:0 overruns:1 carrier:0
+	    collisions:0 txqueuelen:100
+	    Interrupt:10 Base address:0x1080
 
-eth1      Link encap:Ethernet  HWaddr 00:C0:F0:1F:37:B4
-          UP BROADCAST RUNNING SLAVE MULTICAST  MTU:1500  Metric:1
-          RX packets:3651769 errors:0 dropped:0 overruns:0 frame:0
-          TX packets:1643480 errors:0 dropped:0 overruns:0 carrier:0
-          collisions:0 txqueuelen:100
-          Interrupt:9 Base address:0x1400
+  eth1      Link encap:Ethernet  HWaddr 00:C0:F0:1F:37:B4
+	    UP BROADCAST RUNNING SLAVE MULTICAST  MTU:1500  Metric:1
+	    RX packets:3651769 errors:0 dropped:0 overruns:0 frame:0
+	    TX packets:1643480 errors:0 dropped:0 overruns:0 carrier:0
+	    collisions:0 txqueuelen:100
+	    Interrupt:9 Base address:0x1400
 
 5. Switch Configuration
 =======================
 
-	For this section, "switch" refers to whatever system the
+For this section, "switch" refers to whatever system the
 bonded devices are directly connected to (i.e., where the other end of
 the cable plugs into).  This may be an actual dedicated switch device,
 or it may be another regular system (e.g., another computer running
 Linux),
 
-	The active-backup, balance-tlb and balance-alb modes do not
+The active-backup, balance-tlb and balance-alb modes do not
 require any specific configuration of the switch.
 
-	The 802.3ad mode requires that the switch have the appropriate
+The 802.3ad mode requires that the switch have the appropriate
 ports configured as an 802.3ad aggregation.  The precise method used
 to configure this varies from switch to switch, but, for example, a
 Cisco 3550 series switch requires that the appropriate ports first be
@@ -1804,7 +1839,7 @@ grouped together in a single etherchannel instance, then that
 etherchannel is set to mode "lacp" to enable 802.3ad (instead of
 standard EtherChannel).
 
-	The balance-rr, balance-xor and broadcast modes generally
+The balance-rr, balance-xor and broadcast modes generally
 require that the switch have the appropriate ports grouped together.
 The nomenclature for such a group differs between switches, it may be
 called an "etherchannel" (as in the Cisco example, above), a "trunk
@@ -1820,7 +1855,7 @@ with another EtherChannel group.
 6. 802.1q VLAN Support
 ======================
 
-	It is possible to configure VLAN devices over a bond interface
+It is possible to configure VLAN devices over a bond interface
 using the 8021q driver.  However, only packets coming from the 8021q
 driver and passing through bonding will be tagged by default.  Self
 generated packets, for example, bonding's learning packets or ARP
@@ -1829,7 +1864,7 @@ tagged internally by bonding itself.  As a result, bonding must
 "learn" the VLAN IDs configured above it, and use those IDs to tag
 self generated packets.
 
-	For reasons of simplicity, and to support the use of adapters
+For reasons of simplicity, and to support the use of adapters
 that can do VLAN hardware acceleration offloading, the bonding
 interface declares itself as fully hardware offloading capable, it gets
 the add_vid/kill_vid notifications to gather the necessary
@@ -1839,7 +1874,7 @@ should go through an adapter that is not offloading capable are
 "un-accelerated" by the bonding driver so the VLAN tag sits in the
 regular location.
 
-	VLAN interfaces *must* be added on top of a bonding interface
+VLAN interfaces *must* be added on top of a bonding interface
 only after enslaving at least one slave.  The bonding interface has a
 hardware address of 00:00:00:00:00:00 until the first slave is added.
 If the VLAN interface is created prior to the first enslavement, it
@@ -1847,23 +1882,23 @@ would pick up the all-zeroes hardware address.  Once the first slave
 is attached to the bond, the bond device itself will pick up the
 slave's hardware address, which is then available for the VLAN device.
 
-	Also, be aware that a similar problem can occur if all slaves
+Also, be aware that a similar problem can occur if all slaves
 are released from a bond that still has one or more VLAN interfaces on
 top of it.  When a new slave is added, the bonding interface will
 obtain its hardware address from the first slave, which might not
 match the hardware address of the VLAN interfaces (which was
 ultimately copied from an earlier slave).
 
-	There are two methods to insure that the VLAN device operates
+There are two methods to insure that the VLAN device operates
 with the correct hardware address if all slaves are removed from a
 bond interface:
 
-	1. Remove all VLAN interfaces then recreate them
+1. Remove all VLAN interfaces then recreate them
 
-	2. Set the bonding interface's hardware address so that it
+2. Set the bonding interface's hardware address so that it
 matches the hardware address of the VLAN interfaces.
 
-	Note that changing a VLAN interface's HW address would set the
+Note that changing a VLAN interface's HW address would set the
 underlying device -- i.e. the bonding interface -- to promiscuous
 mode, which might not be what you want.
 
@@ -1871,24 +1906,24 @@ mode, which might not be what you want.
 7. Link Monitoring
 ==================
 
-	The bonding driver at present supports two schemes for
+The bonding driver at present supports two schemes for
 monitoring a slave device's link state: the ARP monitor and the MII
 monitor.
 
-	At the present time, due to implementation restrictions in the
+At the present time, due to implementation restrictions in the
 bonding driver itself, it is not possible to enable both ARP and MII
 monitoring simultaneously.
 
 7.1 ARP Monitor Operation
 -------------------------
 
-	The ARP monitor operates as its name suggests: it sends ARP
+The ARP monitor operates as its name suggests: it sends ARP
 queries to one or more designated peer systems on the network, and
 uses the response as an indication that the link is operating.  This
 gives some assurance that traffic is actually flowing to and from one
 or more peers on the local network.
 
-	The ARP monitor relies on the device driver itself to verify
+The ARP monitor relies on the device driver itself to verify
 that traffic is flowing.  In particular, the driver must keep up to
 date the last receive time, dev->last_rx.  Drivers that use NETIF_F_LLTX
 flag must also update netdev_queue->trans_start.  If they do not, then the
@@ -1900,36 +1935,36 @@ your device driver is not updating last_rx and trans_start.
 7.2 Configuring Multiple ARP Targets
 ------------------------------------
 
-	While ARP monitoring can be done with just one target, it can
+While ARP monitoring can be done with just one target, it can
 be useful in a High Availability setup to have several targets to
 monitor.  In the case of just one target, the target itself may go
 down or have a problem making it unresponsive to ARP requests.  Having
 an additional target (or several) increases the reliability of the ARP
 monitoring.
 
-	Multiple ARP targets must be separated by commas as follows:
+Multiple ARP targets must be separated by commas as follows::
 
-# example options for ARP monitoring with three targets
-alias bond0 bonding
-options bond0 arp_interval=60 arp_ip_target=192.168.0.1,192.168.0.3,192.168.0.9
+ # example options for ARP monitoring with three targets
+ alias bond0 bonding
+ options bond0 arp_interval=60 arp_ip_target=192.168.0.1,192.168.0.3,192.168.0.9
 
-	For just a single target the options would resemble:
+For just a single target the options would resemble::
 
-# example options for ARP monitoring with one target
-alias bond0 bonding
-options bond0 arp_interval=60 arp_ip_target=192.168.0.100
+    # example options for ARP monitoring with one target
+    alias bond0 bonding
+    options bond0 arp_interval=60 arp_ip_target=192.168.0.100
 
 
 7.3 MII Monitor Operation
 -------------------------
 
-	The MII monitor monitors only the carrier state of the local
+The MII monitor monitors only the carrier state of the local
 network interface.  It accomplishes this in one of three ways: by
 depending upon the device driver to maintain its carrier state, by
 querying the device's MII registers, or by making an ethtool query to
 the device.
 
-	If the use_carrier module parameter is 1 (the default value),
+If the use_carrier module parameter is 1 (the default value),
 then the MII monitor will rely on the driver for carrier state
 information (via the netif_carrier subsystem).  As explained in the
 use_carrier parameter information, above, if the MII monitor fails to
@@ -1937,7 +1972,7 @@ detect carrier loss on the device (e.g., when the cable is physically
 disconnected), it may be that the driver does not support
 netif_carrier.
 
-	If use_carrier is 0, then the MII monitor will first query the
+If use_carrier is 0, then the MII monitor will first query the
 device's (via ioctl) MII registers and check the link state.  If that
 request fails (not just that it returns carrier down), then the MII
 monitor will make an ethtool ETHOOL_GLINK request to attempt to obtain
@@ -1952,25 +1987,25 @@ up.
 8.1 Adventures in Routing
 -------------------------
 
-	When bonding is configured, it is important that the slave
+When bonding is configured, it is important that the slave
 devices not have routes that supersede routes of the master (or,
 generally, not have routes at all).  For example, suppose the bonding
 device bond0 has two slaves, eth0 and eth1, and the routing table is
-as follows:
+as follows::
 
-Kernel IP routing table
-Destination     Gateway         Genmask         Flags   MSS Window  irtt Iface
-10.0.0.0        0.0.0.0         255.255.0.0     U        40 0          0 eth0
-10.0.0.0        0.0.0.0         255.255.0.0     U        40 0          0 eth1
-10.0.0.0        0.0.0.0         255.255.0.0     U        40 0          0 bond0
-127.0.0.0       0.0.0.0         255.0.0.0       U        40 0          0 lo
+  Kernel IP routing table
+  Destination     Gateway         Genmask         Flags   MSS Window  irtt Iface
+  10.0.0.0        0.0.0.0         255.255.0.0     U        40 0          0 eth0
+  10.0.0.0        0.0.0.0         255.255.0.0     U        40 0          0 eth1
+  10.0.0.0        0.0.0.0         255.255.0.0     U        40 0          0 bond0
+  127.0.0.0       0.0.0.0         255.0.0.0       U        40 0          0 lo
 
-	This routing configuration will likely still update the
+This routing configuration will likely still update the
 receive/transmit times in the driver (needed by the ARP monitor), but
 may bypass the bonding driver (because outgoing traffic to, in this
 case, another host on network 10 would use eth0 or eth1 before bond0).
 
-	The ARP monitor (and ARP itself) may become confused by this
+The ARP monitor (and ARP itself) may become confused by this
 configuration, because ARP requests (generated by the ARP monitor)
 will be sent on one interface (bond0), but the corresponding reply
 will arrive on a different interface (eth0).  This reply looks to ARP
@@ -1978,7 +2013,7 @@ as an unsolicited ARP reply (because ARP matches replies on an
 interface basis), and is discarded.  The MII monitor is not affected
 by the state of the routing table.
 
-	The solution here is simply to insure that slaves do not have
+The solution here is simply to insure that slaves do not have
 routes of their own, and if for some reason they must, those routes do
 not supersede routes of their master.  This should generally be the
 case, but unusual configurations or errant manual or automatic static
@@ -1987,22 +2022,22 @@ route additions may cause trouble.
 8.2 Ethernet Device Renaming
 ----------------------------
 
-	On systems with network configuration scripts that do not
+On systems with network configuration scripts that do not
 associate physical devices directly with network interface names (so
 that the same physical device always has the same "ethX" name), it may
 be necessary to add some special logic to config files in
 /etc/modprobe.d/.
 
-	For example, given a modules.conf containing the following:
+For example, given a modules.conf containing the following::
 
-alias bond0 bonding
-options bond0 mode=some-mode miimon=50
-alias eth0 tg3
-alias eth1 tg3
-alias eth2 e1000
-alias eth3 e1000
+	alias bond0 bonding
+	options bond0 mode=some-mode miimon=50
+	alias eth0 tg3
+	alias eth1 tg3
+	alias eth2 e1000
+	alias eth3 e1000
 
-	If neither eth0 and eth1 are slaves to bond0, then when the
+If neither eth0 and eth1 are slaves to bond0, then when the
 bond0 interface comes up, the devices may end up reordered.  This
 happens because bonding is loaded first, then its slave device's
 drivers are loaded next.  Since no other drivers have been loaded,
@@ -2010,36 +2045,36 @@ when the e1000 driver loads, it will receive eth0 and eth1 for its
 devices, but the bonding configuration tries to enslave eth2 and eth3
 (which may later be assigned to the tg3 devices).
 
-	Adding the following:
+Adding the following::
 
-add above bonding e1000 tg3
+	add above bonding e1000 tg3
 
-	causes modprobe to load e1000 then tg3, in that order, when
+causes modprobe to load e1000 then tg3, in that order, when
 bonding is loaded.  This command is fully documented in the
 modules.conf manual page.
 
-	On systems utilizing modprobe an equivalent problem can occur.
+On systems utilizing modprobe an equivalent problem can occur.
 In this case, the following can be added to config files in
-/etc/modprobe.d/ as:
+/etc/modprobe.d/ as::
 
-softdep bonding pre: tg3 e1000
+	softdep bonding pre: tg3 e1000
 
-	This will load tg3 and e1000 modules before loading the bonding one.
+This will load tg3 and e1000 modules before loading the bonding one.
 Full documentation on this can be found in the modprobe.d and modprobe
 manual pages.
 
 8.3. Painfully Slow Or No Failed Link Detection By Miimon
 ---------------------------------------------------------
 
-	By default, bonding enables the use_carrier option, which
+By default, bonding enables the use_carrier option, which
 instructs bonding to trust the driver to maintain carrier state.
 
-	As discussed in the options section, above, some drivers do
+As discussed in the options section, above, some drivers do
 not support the netif_carrier_on/_off link state tracking system.
 With use_carrier enabled, bonding will always see these links as up,
 regardless of their actual state.
 
-	Additionally, other drivers do support netif_carrier, but do
+Additionally, other drivers do support netif_carrier, but do
 not maintain it in real time, e.g., only polling the link state at
 some fixed interval.  In this case, miimon will detect failures, but
 only after some long period of time has expired.  If it appears that
@@ -2051,7 +2086,7 @@ use_carrier=0 method of querying the registers directly works).  If
 use_carrier=0 does not improve the failover, then the driver may cache
 the registers, or the problem may be elsewhere.
 
-	Also, remember that miimon only checks for the device's
+Also, remember that miimon only checks for the device's
 carrier state.  It has no way to determine the state of devices on or
 beyond other ports of a switch, or if a switch is refusing to pass
 traffic while still maintaining carrier on.
@@ -2059,7 +2094,7 @@ traffic while still maintaining carrier on.
 9. SNMP agents
 ===============
 
-	If running SNMP agents, the bonding driver should be loaded
+If running SNMP agents, the bonding driver should be loaded
 before any network drivers participating in a bond.  This requirement
 is due to the interface index (ipAdEntIfIndex) being associated to
 the first interface found with a given IP address.  That is, there is
@@ -2070,6 +2105,8 @@ with the eth0 interface.  This configuration is shown below, the IP
 address 192.168.1.1 has an interface index of 2 which indexes to eth0
 in the ifDescr table (ifDescr.2).
 
+::
+
      interfaces.ifTable.ifEntry.ifDescr.1 = lo
      interfaces.ifTable.ifEntry.ifDescr.2 = eth0
      interfaces.ifTable.ifEntry.ifDescr.3 = eth1
@@ -2081,7 +2118,7 @@ in the ifDescr table (ifDescr.2).
      ip.ipAddrTable.ipAddrEntry.ipAdEntIfIndex.10.74.20.94 = 4
      ip.ipAddrTable.ipAddrEntry.ipAdEntIfIndex.127.0.0.1 = 1
 
-	This problem is avoided by loading the bonding driver before
+This problem is avoided by loading the bonding driver before
 any network drivers participating in a bond.  Below is an example of
 loading the bonding driver first, the IP address 192.168.1.1 is
 correctly associated with ifDescr.2.
@@ -2097,7 +2134,7 @@ correctly associated with ifDescr.2.
      ip.ipAddrTable.ipAddrEntry.ipAdEntIfIndex.10.74.20.94 = 5
      ip.ipAddrTable.ipAddrEntry.ipAdEntIfIndex.127.0.0.1 = 1
 
-	While some distributions may not report the interface name in
+While some distributions may not report the interface name in
 ifDescr, the association between the IP address and IfIndex remains
 and SNMP functions such as Interface_Scan_Next will report that
 association.
@@ -2105,34 +2142,34 @@ association.
 10. Promiscuous mode
 ====================
 
-	When running network monitoring tools, e.g., tcpdump, it is
+When running network monitoring tools, e.g., tcpdump, it is
 common to enable promiscuous mode on the device, so that all traffic
 is seen (instead of seeing only traffic destined for the local host).
 The bonding driver handles promiscuous mode changes to the bonding
 master device (e.g., bond0), and propagates the setting to the slave
 devices.
 
-	For the balance-rr, balance-xor, broadcast, and 802.3ad modes,
+For the balance-rr, balance-xor, broadcast, and 802.3ad modes,
 the promiscuous mode setting is propagated to all slaves.
 
-	For the active-backup, balance-tlb and balance-alb modes, the
+For the active-backup, balance-tlb and balance-alb modes, the
 promiscuous mode setting is propagated only to the active slave.
 
-	For balance-tlb mode, the active slave is the slave currently
+For balance-tlb mode, the active slave is the slave currently
 receiving inbound traffic.
 
-	For balance-alb mode, the active slave is the slave used as a
+For balance-alb mode, the active slave is the slave used as a
 "primary."  This slave is used for mode-specific control traffic, for
 sending to peers that are unassigned or if the load is unbalanced.
 
-	For the active-backup, balance-tlb and balance-alb modes, when
+For the active-backup, balance-tlb and balance-alb modes, when
 the active slave changes (e.g., due to a link failure), the
 promiscuous setting will be propagated to the new active slave.
 
 11. Configuring Bonding for High Availability
 =============================================
 
-	High Availability refers to configurations that provide
+High Availability refers to configurations that provide
 maximum network availability by having redundant or backup devices,
 links or switches between the host and the rest of the world.  The
 goal is to provide the maximum availability of network connectivity
@@ -2142,7 +2179,7 @@ could provide higher throughput.
 11.1 High Availability in a Single Switch Topology
 --------------------------------------------------
 
-	If two hosts (or a host and a single switch) are directly
+If two hosts (or a host and a single switch) are directly
 connected via multiple physical links, then there is no availability
 penalty to optimizing for maximum bandwidth.  In this case, there is
 only one switch (or peer), so if it fails, there is no alternative
@@ -2150,32 +2187,32 @@ access to fail over to.  Additionally, the bonding load balance modes
 support link monitoring of their members, so if individual links fail,
 the load will be rebalanced across the remaining devices.
 
-	See Section 12, "Configuring Bonding for Maximum Throughput"
+See Section 12, "Configuring Bonding for Maximum Throughput"
 for information on configuring bonding with one peer device.
 
 11.2 High Availability in a Multiple Switch Topology
 ----------------------------------------------------
 
-	With multiple switches, the configuration of bonding and the
+With multiple switches, the configuration of bonding and the
 network changes dramatically.  In multiple switch topologies, there is
 a trade off between network availability and usable bandwidth.
 
-	Below is a sample network, configured to maximize the
-availability of the network:
+Below is a sample network, configured to maximize the
+availability of the network::
 
-                |                                     |
-                |port3                           port3|
-          +-----+----+                          +-----+----+
-          |          |port2       ISL      port2|          |
-          | switch A +--------------------------+ switch B |
-          |          |                          |          |
-          +-----+----+                          +-----++---+
-                |port1                           port1|
-                |             +-------+               |
-                +-------------+ host1 +---------------+
-                         eth0 +-------+ eth1
+		|                                     |
+		|port3                           port3|
+	  +-----+----+                          +-----+----+
+	  |          |port2       ISL      port2|          |
+	  | switch A +--------------------------+ switch B |
+	  |          |                          |          |
+	  +-----+----+                          +-----++---+
+		|port1                           port1|
+		|             +-------+               |
+		+-------------+ host1 +---------------+
+			 eth0 +-------+ eth1
 
-	In this configuration, there is a link between the two
+In this configuration, there is a link between the two
 switches (ISL, or inter switch link), and multiple ports connecting to
 the outside world ("port3" on each switch).  There is no technical
 reason that this could not be extended to a third switch.
@@ -2183,19 +2220,21 @@ reason that this could not be extended to a third switch.
 11.2.1 HA Bonding Mode Selection for Multiple Switch Topology
 -------------------------------------------------------------
 
-	In a topology such as the example above, the active-backup and
+In a topology such as the example above, the active-backup and
 broadcast modes are the only useful bonding modes when optimizing for
 availability; the other modes require all links to terminate on the
 same peer for them to behave rationally.
 
-active-backup: This is generally the preferred mode, particularly if
+active-backup:
+	This is generally the preferred mode, particularly if
 	the switches have an ISL and play together well.  If the
 	network configuration is such that one switch is specifically
 	a backup switch (e.g., has lower capacity, higher cost, etc),
 	then the primary option can be used to insure that the
 	preferred link is always used when it is available.
 
-broadcast: This mode is really a special purpose mode, and is suitable
+broadcast:
+	This mode is really a special purpose mode, and is suitable
 	only for very specific needs.  For example, if the two
 	switches are not connected (no ISL), and the networks beyond
 	them are totally independent.  In this case, if it is
@@ -2205,7 +2244,7 @@ broadcast: This mode is really a special purpose mode, and is suitable
 11.2.2 HA Link Monitoring Selection for Multiple Switch Topology
 ----------------------------------------------------------------
 
-	The choice of link monitoring ultimately depends upon your
+The choice of link monitoring ultimately depends upon your
 switch.  If the switch can reliably fail ports in response to other
 failures, then either the MII or ARP monitors should work.  For
 example, in the above example, if the "port3" link fails at the remote
@@ -2213,7 +2252,7 @@ end, the MII monitor has no direct means to detect this.  The ARP
 monitor could be configured with a target at the remote end of port3,
 thus detecting that failure without switch support.
 
-	In general, however, in a multiple switch topology, the ARP
+In general, however, in a multiple switch topology, the ARP
 monitor can provide a higher level of reliability in detecting end to
 end connectivity failures (which may be caused by the failure of any
 individual component to pass traffic for any reason).  Additionally,
@@ -2222,7 +2261,7 @@ one for each switch in the network).  This will insure that,
 regardless of which switch is active, the ARP monitor has a suitable
 target to query.
 
-	Note, also, that of late many switches now support a functionality
+Note, also, that of late many switches now support a functionality
 generally referred to as "trunk failover."  This is a feature of the
 switch that causes the link state of a particular switch port to be set
 down (or up) when the state of another switch port goes down (or up).
@@ -2238,18 +2277,18 @@ suitable switches.
 12.1 Maximizing Throughput in a Single Switch Topology
 ------------------------------------------------------
 
-	In a single switch configuration, the best method to maximize
+In a single switch configuration, the best method to maximize
 throughput depends upon the application and network environment.  The
 various load balancing modes each have strengths and weaknesses in
 different environments, as detailed below.
 
-	For this discussion, we will break down the topologies into
+For this discussion, we will break down the topologies into
 two categories.  Depending upon the destination of most traffic, we
 categorize them into either "gatewayed" or "local" configurations.
 
-	In a gatewayed configuration, the "switch" is acting primarily
+In a gatewayed configuration, the "switch" is acting primarily
 as a router, and the majority of traffic passes through this router to
-other networks.  An example would be the following:
+other networks.  An example would be the following::
 
 
      +----------+                     +----------+
@@ -2259,25 +2298,25 @@ other networks.  An example would be the following:
      |          |eth1            port2|          | here somewhere
      +----------+                     +----------+
 
-	The router may be a dedicated router device, or another host
+The router may be a dedicated router device, or another host
 acting as a gateway.  For our discussion, the important point is that
 the majority of traffic from Host A will pass through the router to
 some other network before reaching its final destination.
 
-	In a gatewayed network configuration, although Host A may
+In a gatewayed network configuration, although Host A may
 communicate with many other systems, all of its traffic will be sent
 and received via one other peer on the local network, the router.
 
-	Note that the case of two systems connected directly via
+Note that the case of two systems connected directly via
 multiple physical links is, for purposes of configuring bonding, the
 same as a gatewayed configuration.  In that case, it happens that all
 traffic is destined for the "gateway" itself, not some other network
 beyond the gateway.
 
-	In a local configuration, the "switch" is acting primarily as
+In a local configuration, the "switch" is acting primarily as
 a switch, and the majority of traffic passes through this switch to
 reach other stations on the same network.  An example would be the
-following:
+following::
 
     +----------+            +----------+       +--------+
     |          |eth0   port1|          +-------+ Host B |
@@ -2287,19 +2326,19 @@ following:
     +----------+            +----------+port4             +--------+
 
 
-	Again, the switch may be a dedicated switch device, or another
+Again, the switch may be a dedicated switch device, or another
 host acting as a gateway.  For our discussion, the important point is
 that the majority of traffic from Host A is destined for other hosts
 on the same local network (Hosts B and C in the above example).
 
-	In summary, in a gatewayed configuration, traffic to and from
+In summary, in a gatewayed configuration, traffic to and from
 the bonded device will be to the same MAC level peer on the network
 (the gateway itself, i.e., the router), regardless of its final
 destination.  In a local configuration, traffic flows directly to and
 from the final destinations, thus, each destination (Host B, Host C)
 will be addressed directly by their individual MAC addresses.
 
-	This distinction between a gatewayed and a local network
+This distinction between a gatewayed and a local network
 configuration is important because many of the load balancing modes
 available use the MAC addresses of the local network source and
 destination to make load balancing decisions.  The behavior of each
@@ -2309,11 +2348,12 @@ mode is described below.
 12.1.1 MT Bonding Mode Selection for Single Switch Topology
 -----------------------------------------------------------
 
-	This configuration is the easiest to set up and to understand,
+This configuration is the easiest to set up and to understand,
 although you will have to decide which bonding mode best suits your
 needs.  The trade offs for each mode are detailed below:
 
-balance-rr: This mode is the only mode that will permit a single
+balance-rr:
+	This mode is the only mode that will permit a single
 	TCP/IP connection to stripe traffic across multiple
 	interfaces. It is therefore the only mode that will allow a
 	single TCP/IP stream to utilize more than one interface's
@@ -2351,7 +2391,8 @@ balance-rr: This mode is the only mode that will permit a single
 	This mode requires the switch to have the appropriate ports
 	configured for "etherchannel" or "trunking."
 
-active-backup: There is not much advantage in this network topology to
+active-backup:
+	There is not much advantage in this network topology to
 	the active-backup mode, as the inactive backup devices are all
 	connected to the same peer as the primary.  In this case, a
 	load balancing mode (with link monitoring) will provide the
@@ -2361,7 +2402,8 @@ active-backup: There is not much advantage in this network topology to
 	have value if the hardware available does not support any of
 	the load balance modes.
 
-balance-xor: This mode will limit traffic such that packets destined
+balance-xor:
+	This mode will limit traffic such that packets destined
 	for specific peers will always be sent over the same
 	interface.  Since the destination is determined by the MAC
 	addresses involved, this mode works best in a "local" network
@@ -2373,10 +2415,12 @@ balance-xor: This mode will limit traffic such that packets destined
 	As with balance-rr, the switch ports need to be configured for
 	"etherchannel" or "trunking."
 
-broadcast: Like active-backup, there is not much advantage to this
+broadcast:
+	Like active-backup, there is not much advantage to this
 	mode in this type of network topology.
 
-802.3ad: This mode can be a good choice for this type of network
+802.3ad:
+	This mode can be a good choice for this type of network
 	topology.  The 802.3ad mode is an IEEE standard, so all peers
 	that implement 802.3ad should interoperate well.  The 802.3ad
 	protocol includes automatic configuration of the aggregates,
@@ -2390,7 +2434,7 @@ broadcast: Like active-backup, there is not much advantage to this
 	the same speed and duplex.  Also, as with all bonding load
 	balance modes other than balance-rr, no single connection will
 	be able to utilize more than a single interface's worth of
-	bandwidth.  
+	bandwidth.
 
 	Additionally, the linux bonding 802.3ad implementation
 	distributes traffic by peer (using an XOR of MAC addresses
@@ -2404,7 +2448,8 @@ broadcast: Like active-backup, there is not much advantage to this
 	Finally, the 802.3ad mode mandates the use of the MII monitor,
 	therefore, the ARP monitor is not available in this mode.
 
-balance-tlb: The balance-tlb mode balances outgoing traffic by peer.
+balance-tlb:
+	The balance-tlb mode balances outgoing traffic by peer.
 	Since the balancing is done according to MAC address, in a
 	"gatewayed" configuration (as described above), this mode will
 	send all traffic across a single device.  However, in a
@@ -2422,7 +2467,8 @@ balance-tlb: The balance-tlb mode balances outgoing traffic by peer.
 	network device driver of the slave interfaces, and the ARP
 	monitor is not available.
 
-balance-alb: This mode is everything that balance-tlb is, and more.
+balance-alb:
+	This mode is everything that balance-tlb is, and more.
 	It has all of the features (and restrictions) of balance-tlb,
 	and will also balance incoming traffic from local network
 	peers (as described in the Bonding Module Options section,
@@ -2435,7 +2481,7 @@ balance-alb: This mode is everything that balance-tlb is, and more.
 12.1.2 MT Link Monitoring for Single Switch Topology
 ----------------------------------------------------
 
-	The choice of link monitoring may largely depend upon which
+The choice of link monitoring may largely depend upon which
 mode you choose to use.  The more advanced load balancing modes do not
 support the use of the ARP monitor, and are thus restricted to using
 the MII monitor (which does not provide as high a level of end to end
@@ -2444,27 +2490,27 @@ assurance as the ARP monitor).
 12.2 Maximum Throughput in a Multiple Switch Topology
 -----------------------------------------------------
 
-	Multiple switches may be utilized to optimize for throughput
+Multiple switches may be utilized to optimize for throughput
 when they are configured in parallel as part of an isolated network
-between two or more systems, for example:
+between two or more systems, for example::
 
-                       +-----------+
-                       |  Host A   | 
-                       +-+---+---+-+
-                         |   |   |
-                +--------+   |   +---------+
-                |            |             |
-         +------+---+  +-----+----+  +-----+----+
-         | Switch A |  | Switch B |  | Switch C |
-         +------+---+  +-----+----+  +-----+----+
-                |            |             |
-                +--------+   |   +---------+
-                         |   |   |
-                       +-+---+---+-+
-                       |  Host B   | 
-                       +-----------+
+		       +-----------+
+		       |  Host A   |
+		       +-+---+---+-+
+			 |   |   |
+		+--------+   |   +---------+
+		|            |             |
+	 +------+---+  +-----+----+  +-----+----+
+	 | Switch A |  | Switch B |  | Switch C |
+	 +------+---+  +-----+----+  +-----+----+
+		|            |             |
+		+--------+   |   +---------+
+			 |   |   |
+		       +-+---+---+-+
+		       |  Host B   |
+		       +-----------+
 
-	In this configuration, the switches are isolated from one
+In this configuration, the switches are isolated from one
 another.  One reason to employ a topology such as this is for an
 isolated network with many hosts (a cluster configured for high
 performance, for example), using multiple smaller switches can be more
@@ -2472,14 +2518,14 @@ cost effective than a single larger switch, e.g., on a network with 24
 hosts, three 24 port switches can be significantly less expensive than
 a single 72 port switch.
 
-	If access beyond the network is required, an individual host
+If access beyond the network is required, an individual host
 can be equipped with an additional network device connected to an
 external network; this host then additionally acts as a gateway.
 
 12.2.1 MT Bonding Mode Selection for Multiple Switch Topology
 -------------------------------------------------------------
 
-	In actual practice, the bonding mode typically employed in
+In actual practice, the bonding mode typically employed in
 configurations of this type is balance-rr.  Historically, in this
 network configuration, the usual caveats about out of order packet
 delivery are mitigated by the use of network adapters that do not do
@@ -2492,7 +2538,7 @@ utilize greater than one interface's bandwidth.
 12.2.2 MT Link Monitoring for Multiple Switch Topology
 ------------------------------------------------------
 
-	Again, in actual practice, the MII monitor is most often used
+Again, in actual practice, the MII monitor is most often used
 in this configuration, as performance is given preference over
 availability.  The ARP monitor will function in this topology, but its
 advantages over the MII monitor are mitigated by the volume of probes
@@ -2505,10 +2551,10 @@ host in the network is configured with bonding).
 13.1 Link Establishment and Failover Delays
 -------------------------------------------
 
-	Some switches exhibit undesirable behavior with regard to the
+Some switches exhibit undesirable behavior with regard to the
 timing of link up and down reporting by the switch.
 
-	First, when a link comes up, some switches may indicate that
+First, when a link comes up, some switches may indicate that
 the link is up (carrier available), but not pass traffic over the
 interface for some period of time.  This delay is typically due to
 some type of autonegotiation or routing protocol, but may also occur
@@ -2517,12 +2563,12 @@ failure).  If you find this to be a problem, specify an appropriate
 value to the updelay bonding module option to delay the use of the
 relevant interface(s).
 
-	Second, some switches may "bounce" the link state one or more
+Second, some switches may "bounce" the link state one or more
 times while a link is changing state.  This occurs most commonly while
 the switch is initializing.  Again, an appropriate updelay value may
 help.
 
-	Note that when a bonding interface has no active links, the
+Note that when a bonding interface has no active links, the
 driver will immediately reuse the first link that goes up, even if the
 updelay parameter has been specified (the updelay is ignored in this
 case).  If there are slave interfaces waiting for the updelay timeout
@@ -2532,7 +2578,7 @@ value of updelay has been overestimated, and since this occurs only in
 cases with no connectivity, there is no additional penalty for
 ignoring the updelay.
 
-	In addition to the concerns about switch timings, if your
+In addition to the concerns about switch timings, if your
 switches take a long time to go into backup mode, it may be desirable
 to not activate a backup interface immediately after a link goes down.
 Failover may be delayed via the downdelay bonding module option.
@@ -2540,31 +2586,31 @@ Failover may be delayed via the downdelay bonding module option.
 13.2 Duplicated Incoming Packets
 --------------------------------
 
-	NOTE: Starting with version 3.0.2, the bonding driver has logic to
+NOTE: Starting with version 3.0.2, the bonding driver has logic to
 suppress duplicate packets, which should largely eliminate this problem.
 The following description is kept for reference.
 
-	It is not uncommon to observe a short burst of duplicated
+It is not uncommon to observe a short burst of duplicated
 traffic when the bonding device is first used, or after it has been
 idle for some period of time.  This is most easily observed by issuing
 a "ping" to some other host on the network, and noticing that the
 output from ping flags duplicates (typically one per slave).
 
-	For example, on a bond in active-backup mode with five slaves
-all connected to one switch, the output may appear as follows:
+For example, on a bond in active-backup mode with five slaves
+all connected to one switch, the output may appear as follows::
 
-# ping -n 10.0.4.2
-PING 10.0.4.2 (10.0.4.2) from 10.0.3.10 : 56(84) bytes of data.
-64 bytes from 10.0.4.2: icmp_seq=1 ttl=64 time=13.7 ms
-64 bytes from 10.0.4.2: icmp_seq=1 ttl=64 time=13.8 ms (DUP!)
-64 bytes from 10.0.4.2: icmp_seq=1 ttl=64 time=13.8 ms (DUP!)
-64 bytes from 10.0.4.2: icmp_seq=1 ttl=64 time=13.8 ms (DUP!)
-64 bytes from 10.0.4.2: icmp_seq=1 ttl=64 time=13.8 ms (DUP!)
-64 bytes from 10.0.4.2: icmp_seq=2 ttl=64 time=0.216 ms
-64 bytes from 10.0.4.2: icmp_seq=3 ttl=64 time=0.267 ms
-64 bytes from 10.0.4.2: icmp_seq=4 ttl=64 time=0.222 ms
+	# ping -n 10.0.4.2
+	PING 10.0.4.2 (10.0.4.2) from 10.0.3.10 : 56(84) bytes of data.
+	64 bytes from 10.0.4.2: icmp_seq=1 ttl=64 time=13.7 ms
+	64 bytes from 10.0.4.2: icmp_seq=1 ttl=64 time=13.8 ms (DUP!)
+	64 bytes from 10.0.4.2: icmp_seq=1 ttl=64 time=13.8 ms (DUP!)
+	64 bytes from 10.0.4.2: icmp_seq=1 ttl=64 time=13.8 ms (DUP!)
+	64 bytes from 10.0.4.2: icmp_seq=1 ttl=64 time=13.8 ms (DUP!)
+	64 bytes from 10.0.4.2: icmp_seq=2 ttl=64 time=0.216 ms
+	64 bytes from 10.0.4.2: icmp_seq=3 ttl=64 time=0.267 ms
+	64 bytes from 10.0.4.2: icmp_seq=4 ttl=64 time=0.222 ms
 
-	This is not due to an error in the bonding driver, rather, it
+This is not due to an error in the bonding driver, rather, it
 is a side effect of how many switches update their MAC forwarding
 tables.  Initially, the switch does not associate the MAC address in
 the packet with a particular switch port, and so it may send the
@@ -2574,7 +2620,7 @@ single switch, when the switch (temporarily) floods the traffic to all
 ports, the bond device receives multiple copies of the same packet
 (one per slave device).
 
-	The duplicated packet behavior is switch dependent, some
+The duplicated packet behavior is switch dependent, some
 switches exhibit this, and some do not.  On switches that display this
 behavior, it can be induced by clearing the MAC forwarding table (on
 most Cisco switches, the privileged command "clear mac address-table
@@ -2583,16 +2629,16 @@ dynamic" will accomplish this).
 14. Hardware Specific Considerations
 ====================================
 
-	This section contains additional information for configuring
+This section contains additional information for configuring
 bonding on specific hardware platforms, or for interfacing bonding
 with particular switches or other devices.
 
 14.1 IBM BladeCenter
 --------------------
 
-	This applies to the JS20 and similar systems.
+This applies to the JS20 and similar systems.
 
-	On the JS20 blades, the bonding driver supports only
+On the JS20 blades, the bonding driver supports only
 balance-rr, active-backup, balance-tlb and balance-alb modes.  This is
 largely due to the network topology inside the BladeCenter, detailed
 below.
@@ -2600,7 +2646,7 @@ below.
 JS20 network adapter information
 --------------------------------
 
-	All JS20s come with two Broadcom Gigabit Ethernet ports
+All JS20s come with two Broadcom Gigabit Ethernet ports
 integrated on the planar (that's "motherboard" in IBM-speak).  In the
 BladeCenter chassis, the eth0 port of all JS20 blades is hard wired to
 I/O Module #1; similarly, all eth1 ports are wired to I/O Module #2.
@@ -2608,36 +2654,36 @@ An add-on Broadcom daughter card can be installed on a JS20 to provide
 two more Gigabit Ethernet ports.  These ports, eth2 and eth3, are
 wired to I/O Modules 3 and 4, respectively.
 
-	Each I/O Module may contain either a switch or a passthrough
+Each I/O Module may contain either a switch or a passthrough
 module (which allows ports to be directly connected to an external
 switch).  Some bonding modes require a specific BladeCenter internal
 network topology in order to function; these are detailed below.
 
-	Additional BladeCenter-specific networking information can be
+Additional BladeCenter-specific networking information can be
 found in two IBM Redbooks (www.ibm.com/redbooks):
 
-"IBM eServer BladeCenter Networking Options"
-"IBM eServer BladeCenter Layer 2-7 Network Switching"
+- "IBM eServer BladeCenter Networking Options"
+- "IBM eServer BladeCenter Layer 2-7 Network Switching"
 
 BladeCenter networking configuration
 ------------------------------------
 
-	Because a BladeCenter can be configured in a very large number
+Because a BladeCenter can be configured in a very large number
 of ways, this discussion will be confined to describing basic
 configurations.
 
-	Normally, Ethernet Switch Modules (ESMs) are used in I/O
+Normally, Ethernet Switch Modules (ESMs) are used in I/O
 modules 1 and 2.  In this configuration, the eth0 and eth1 ports of a
 JS20 will be connected to different internal switches (in the
 respective I/O modules).
 
-	A passthrough module (OPM or CPM, optical or copper,
+A passthrough module (OPM or CPM, optical or copper,
 passthrough module) connects the I/O module directly to an external
 switch.  By using PMs in I/O module #1 and #2, the eth0 and eth1
 interfaces of a JS20 can be redirected to the outside world and
 connected to a common external switch.
 
-	Depending upon the mix of ESMs and PMs, the network will
+Depending upon the mix of ESMs and PMs, the network will
 appear to bonding as either a single switch topology (all PMs) or as a
 multiple switch topology (one or more ESMs, zero or more PMs).  It is
 also possible to connect ESMs together, resulting in a configuration
@@ -2647,24 +2693,24 @@ Topology," above.
 Requirements for specific modes
 -------------------------------
 
-	The balance-rr mode requires the use of passthrough modules
+The balance-rr mode requires the use of passthrough modules
 for devices in the bond, all connected to an common external switch.
 That switch must be configured for "etherchannel" or "trunking" on the
 appropriate ports, as is usual for balance-rr.
 
-	The balance-alb and balance-tlb modes will function with
+The balance-alb and balance-tlb modes will function with
 either switch modules or passthrough modules (or a mix).  The only
 specific requirement for these modes is that all network interfaces
 must be able to reach all destinations for traffic sent over the
 bonding device (i.e., the network must converge at some point outside
 the BladeCenter).
 
-	The active-backup mode has no additional requirements.
+The active-backup mode has no additional requirements.
 
 Link monitoring issues
 ----------------------
 
-	When an Ethernet Switch Module is in place, only the ARP
+When an Ethernet Switch Module is in place, only the ARP
 monitor will reliably detect link loss to an external switch.  This is
 nothing unusual, but examination of the BladeCenter cabinet would
 suggest that the "external" network ports are the ethernet ports for
@@ -2672,166 +2718,173 @@ the system, when it fact there is a switch between these "external"
 ports and the devices on the JS20 system itself.  The MII monitor is
 only able to detect link failures between the ESM and the JS20 system.
 
-	When a passthrough module is in place, the MII monitor does
+When a passthrough module is in place, the MII monitor does
 detect failures to the "external" port, which is then directly
 connected to the JS20 system.
 
 Other concerns
 --------------
 
-	The Serial Over LAN (SoL) link is established over the primary
+The Serial Over LAN (SoL) link is established over the primary
 ethernet (eth0) only, therefore, any loss of link to eth0 will result
 in losing your SoL connection.  It will not fail over with other
 network traffic, as the SoL system is beyond the control of the
 bonding driver.
 
-	It may be desirable to disable spanning tree on the switch
+It may be desirable to disable spanning tree on the switch
 (either the internal Ethernet Switch Module, or an external switch) to
 avoid fail-over delay issues when using bonding.
 
-	
+
 15. Frequently Asked Questions
 ==============================
 
 1.  Is it SMP safe?
+-------------------
 
-	Yes. The old 2.0.xx channel bonding patch was not SMP safe.
+Yes. The old 2.0.xx channel bonding patch was not SMP safe.
 The new driver was designed to be SMP safe from the start.
 
 2.  What type of cards will work with it?
+-----------------------------------------
 
-	Any Ethernet type cards (you can even mix cards - a Intel
+Any Ethernet type cards (you can even mix cards - a Intel
 EtherExpress PRO/100 and a 3com 3c905b, for example).  For most modes,
 devices need not be of the same speed.
 
-	Starting with version 3.2.1, bonding also supports Infiniband
+Starting with version 3.2.1, bonding also supports Infiniband
 slaves in active-backup mode.
 
 3.  How many bonding devices can I have?
+----------------------------------------
 
-	There is no limit.
+There is no limit.
 
 4.  How many slaves can a bonding device have?
+----------------------------------------------
 
-	This is limited only by the number of network interfaces Linux
+This is limited only by the number of network interfaces Linux
 supports and/or the number of network cards you can place in your
 system.
 
 5.  What happens when a slave link dies?
+----------------------------------------
 
-	If link monitoring is enabled, then the failing device will be
+If link monitoring is enabled, then the failing device will be
 disabled.  The active-backup mode will fail over to a backup link, and
 other modes will ignore the failed link.  The link will continue to be
 monitored, and should it recover, it will rejoin the bond (in whatever
 manner is appropriate for the mode). See the sections on High
 Availability and the documentation for each mode for additional
 information.
-	
-	Link monitoring can be enabled via either the miimon or
+
+Link monitoring can be enabled via either the miimon or
 arp_interval parameters (described in the module parameters section,
 above).  In general, miimon monitors the carrier state as sensed by
 the underlying network device, and the arp monitor (arp_interval)
 monitors connectivity to another host on the local network.
 
-	If no link monitoring is configured, the bonding driver will
+If no link monitoring is configured, the bonding driver will
 be unable to detect link failures, and will assume that all links are
 always available.  This will likely result in lost packets, and a
 resulting degradation of performance.  The precise performance loss
 depends upon the bonding mode and network configuration.
 
 6.  Can bonding be used for High Availability?
+----------------------------------------------
 
-	Yes.  See the section on High Availability for details.
+Yes.  See the section on High Availability for details.
 
 7.  Which switches/systems does it work with?
+---------------------------------------------
 
-	The full answer to this depends upon the desired mode.
+The full answer to this depends upon the desired mode.
 
-	In the basic balance modes (balance-rr and balance-xor), it
+In the basic balance modes (balance-rr and balance-xor), it
 works with any system that supports etherchannel (also called
 trunking).  Most managed switches currently available have such
 support, and many unmanaged switches as well.
 
-	The advanced balance modes (balance-tlb and balance-alb) do
+The advanced balance modes (balance-tlb and balance-alb) do
 not have special switch requirements, but do need device drivers that
 support specific features (described in the appropriate section under
 module parameters, above).
 
-	In 802.3ad mode, it works with systems that support IEEE
+In 802.3ad mode, it works with systems that support IEEE
 802.3ad Dynamic Link Aggregation.  Most managed and many unmanaged
 switches currently available support 802.3ad.
 
-        The active-backup mode should work with any Layer-II switch.
+The active-backup mode should work with any Layer-II switch.
 
 8.  Where does a bonding device get its MAC address from?
+---------------------------------------------------------
 
-	When using slave devices that have fixed MAC addresses, or when
+When using slave devices that have fixed MAC addresses, or when
 the fail_over_mac option is enabled, the bonding device's MAC address is
 the MAC address of the active slave.
 
-	For other configurations, if not explicitly configured (with
+For other configurations, if not explicitly configured (with
 ifconfig or ip link), the MAC address of the bonding device is taken from
 its first slave device.  This MAC address is then passed to all following
 slaves and remains persistent (even if the first slave is removed) until
 the bonding device is brought down or reconfigured.
 
-	If you wish to change the MAC address, you can set it with
-ifconfig or ip link:
+If you wish to change the MAC address, you can set it with
+ifconfig or ip link::
 
-# ifconfig bond0 hw ether 00:11:22:33:44:55
+	# ifconfig bond0 hw ether 00:11:22:33:44:55
 
-# ip link set bond0 address 66:77:88:99:aa:bb
+	# ip link set bond0 address 66:77:88:99:aa:bb
 
-	The MAC address can be also changed by bringing down/up the
-device and then changing its slaves (or their order):
+The MAC address can be also changed by bringing down/up the
+device and then changing its slaves (or their order)::
 
-# ifconfig bond0 down ; modprobe -r bonding
-# ifconfig bond0 .... up
-# ifenslave bond0 eth...
+	# ifconfig bond0 down ; modprobe -r bonding
+	# ifconfig bond0 .... up
+	# ifenslave bond0 eth...
 
-	This method will automatically take the address from the next
+This method will automatically take the address from the next
 slave that is added.
 
-	To restore your slaves' MAC addresses, you need to detach them
-from the bond (`ifenslave -d bond0 eth0'). The bonding driver will
+To restore your slaves' MAC addresses, you need to detach them
+from the bond (``ifenslave -d bond0 eth0``). The bonding driver will
 then restore the MAC addresses that the slaves had before they were
 enslaved.
 
 16. Resources and Links
 =======================
 
-	The latest version of the bonding driver can be found in the latest
+The latest version of the bonding driver can be found in the latest
 version of the linux kernel, found on http://kernel.org
 
-	The latest version of this document can be found in the latest kernel
-source (named Documentation/networking/bonding.txt).
+The latest version of this document can be found in the latest kernel
+source (named Documentation/networking/bonding.rst).
 
-	Discussions regarding the usage of the bonding driver take place on the
+Discussions regarding the usage of the bonding driver take place on the
 bonding-devel mailing list, hosted at sourceforge.net. If you have questions or
 problems, post them to the list.  The list address is:
 
 bonding-devel at lists.sourceforge.net
 
-	The administrative interface (to subscribe or unsubscribe) can
+The administrative interface (to subscribe or unsubscribe) can
 be found at:
 
 https://lists.sourceforge.net/lists/listinfo/bonding-devel
 
-	Discussions regarding the development of the bonding driver take place
+Discussions regarding the development of the bonding driver take place
 on the main Linux network mailing list, hosted at vger.kernel.org. The list
 address is:
 
 netdev at vger.kernel.org
 
-	The administrative interface (to subscribe or unsubscribe) can
+The administrative interface (to subscribe or unsubscribe) can
 be found at:
 
 http://vger.kernel.org/vger-lists.html#netdev
 
 Donald Becker's Ethernet Drivers and diag programs may be found at :
- - http://web.archive.org/web/*/http://www.scyld.com/network/ 
+
+ - http://web.archive.org/web/%2E/http://www.scyld.com/network/
 
 You will also find a lot of information regarding Ethernet, NWay, MII,
 etc. at www.scyld.com.
-
--- END --
Documentation/networking/device_drivers/intel/e100.rst +1 -1
index caf023cc88de..3ac21e7119a7 100644
@@ -33,7 +33,7 @@ The following features are now available in supported kernels:
  - SNMP
 
 Channel Bonding documentation can be found in the Linux kernel source:
-/Documentation/networking/bonding.txt
+/Documentation/networking/bonding.rst
 
 
 Identifying Your Adapter
Documentation/networking/device_drivers/intel/ixgb.rst +1 -1
index 945018207a92..ab624f1a44a8 100644
@@ -37,7 +37,7 @@ The following features are available in this kernel:
  - SNMP
 
 Channel Bonding documentation can be found in the Linux kernel source:
-/Documentation/networking/bonding.txt
+/Documentation/networking/bonding.rst
 
 The driver information previously displayed in the /proc filesystem is not
 supported in this release.  Alternatively, you can use ethtool (version 1.6
Documentation/networking/index.rst +1 -0
index fbf845fbaff7..22b872834ef0 100644
@@ -44,6 +44,7 @@ Contents:
    atm
    ax25
    baycom
+   bonding
 
 .. only::  subproject and html
 
drivers/net/Kconfig +1 -1
index b103fbdd0f68..4ab6d343fd86 100644
@@ -50,7 +50,7 @@ config BONDING
 	  The driver supports multiple bonding modes to allow for both high
 	  performance and high availability operation.
 
-	  Refer to <file:Documentation/networking/bonding.txt> for more
+	  Refer to <file:Documentation/networking/bonding.rst> for more
 	  information.
 
 	  To compile this driver as a module, choose M here: the module
Signature · 1 line
2.25.4
#10 lore raw

PATCH 10/38 docs: networking: convert cdc_mbim.txt to ReST

In reply to Mauro Carvalho Chehab

- add SPDX header;
- mark code blocks and literals as such;
- use :field: markup;
- adjust identation, whitespaces and blank lines;
- add to networking/index.rst.

---
 .../networking/{cdc_mbim.txt => cdc_mbim.rst} | 76 +++++++++++--------
 Documentation/networking/index.rst            |  1 +
 2 files changed, 47 insertions(+), 30 deletions(-)
 rename Documentation/networking/{cdc_mbim.txt => cdc_mbim.rst} (88%)
Documentation/networking/cdc_mbim.rst renamed from Documentation/networking/cdc_mbim.txt +46 -30
similarity index 88%
rename from Documentation/networking/cdc_mbim.txt
rename to Documentation/networking/cdc_mbim.rst
index 4e68f0bc5dba..0048409c06b4 100644
@@ -1,5 +1,8 @@
-     cdc_mbim - Driver for CDC MBIM Mobile Broadband modems
-    ========================================================
+.. SPDX-License-Identifier: GPL-2.0
+
+======================================================
+cdc_mbim - Driver for CDC MBIM Mobile Broadband modems
+======================================================
 
 The cdc_mbim driver supports USB devices conforming to the "Universal
 Serial Bus Communications Class Subclass Specification for Mobile
@@ -19,9 +22,9 @@ by a cdc_ncm driver parameter:
 
 prefer_mbim
 -----------
-Type:          Boolean
-Valid Range:   N/Y (0-1)
-Default Value: Y (MBIM is preferred)
+:Type:          Boolean
+:Valid Range:   N/Y (0-1)
+:Default Value: Y (MBIM is preferred)
 
 This parameter sets the system policy for NCM/MBIM functions.  Such
 functions will be handled by either the cdc_ncm driver or the cdc_mbim
@@ -44,11 +47,13 @@ userspace MBIM management application always is required to enable a
 MBIM function.
 
 Such userspace applications includes, but are not limited to:
+
  - mbimcli (included with the libmbim [3] library), and
  - ModemManager [4]
 
 Establishing a MBIM IP session reequires at least these actions by the
 management application:
+
  - open the control channel
  - configure network connection settings
  - connect to network
@@ -76,7 +81,7 @@ complies with all the control channel requirements in [1].
 
 The cdc-wdmX device is created as a child of the MBIM control
 interface USB device.  The character device associated with a specific
-MBIM function can be looked up using sysfs.  For example:
+MBIM function can be looked up using sysfs.  For example::
 
  bjorn@nemi:~$ ls /sys/bus/usb/drivers/cdc_mbim/2-4:2.12/usbmisc
  cdc-wdm0
@@ -119,13 +124,15 @@ negotiated control message size.
 
 
 /dev/cdc-wdmX ioctl()
---------------------
+---------------------
 IOCTL_WDM_MAX_COMMAND: Get Maximum Command Size
 This ioctl returns the wMaxControlMessage field of the CDC MBIM
 functional descriptor for MBIM devices.  This is intended as a
 convenience, eliminating the need to parse the USB descriptors from
 userspace.
 
+::
+
 	#include <stdio.h>
 	#include <fcntl.h>
 	#include <sys/ioctl.h>
@@ -178,7 +185,7 @@ VLAN links prior to establishing MBIM IP sessions where the SessionId
 is greater than 0. These links can be added by using the normal VLAN
 kernel interfaces, either ioctl or netlink.
 
-For example, adding a link for a MBIM IP session with SessionId 3:
+For example, adding a link for a MBIM IP session with SessionId 3::
 
   ip link add link wwan0 name wwan0.3 type vlan id 3
 
@@ -207,6 +214,7 @@ the stream to the end user in an appropriate way for the stream type.
 The network device ABI requires a dummy ethernet header for every DSS
 data frame being transported.  The contents of this header is
 arbitrary, with the following exceptions:
+
  - TX frames using an IP protocol (0x0800 or 0x86dd) will be dropped
  - RX frames will have the protocol field set to ETH_P_802_3 (but will
    not be properly formatted 802.3 frames)
@@ -218,7 +226,7 @@ adding the dummy ethernet header on TX and stripping it on RX.
 
 This is a simple example using tools commonly available, exporting
 DssSessionId 5 as a pty character device pointed to by a /dev/nmea
-symlink:
+symlink::
 
   ip link add link wwan0 name wwan0.dss5 type vlan id 261
   ip link set dev wwan0.dss5 up
@@ -236,7 +244,7 @@ map frames to the correct DSS session and adding 18 byte VLAN ethernet
 headers with the appropriate tag on TX.  In this case using a socket
 filter is recommended, matching only the DSS VLAN subset. This avoid
 unnecessary copying of unrelated IP session data to userspace.  For
-example:
+example::
 
   static struct sock_filter dssfilter[] = {
 	/* use special negative offsets to get VLAN tag */
@@ -249,11 +257,11 @@ example:
 	BPF_JUMP(BPF_JMP|BPF_JGE|BPF_K, 512, 3, 0),	/* 511 is last DSS VLAN */
 
 	/* verify ethertype */
-        BPF_STMT(BPF_LD|BPF_H|BPF_ABS, 2 * ETH_ALEN),
-        BPF_JUMP(BPF_JMP|BPF_JEQ|BPF_K, ETH_P_802_3, 0, 1),
+	BPF_STMT(BPF_LD|BPF_H|BPF_ABS, 2 * ETH_ALEN),
+	BPF_JUMP(BPF_JMP|BPF_JEQ|BPF_K, ETH_P_802_3, 0, 1),
 
-        BPF_STMT(BPF_RET|BPF_K, (u_int)-1),	/* accept */
-        BPF_STMT(BPF_RET|BPF_K, 0),		/* ignore */
+	BPF_STMT(BPF_RET|BPF_K, (u_int)-1),	/* accept */
+	BPF_STMT(BPF_RET|BPF_K, 0),		/* ignore */
   };
 
 
@@ -266,6 +274,7 @@ network device.
 
 This mapping implies a few restrictions on multiplexed IPS and DSS
 sessions, which may not always be practical:
+
  - no IPS or DSS session can use a frame size greater than the MTU on
    IP session 0
  - no IPS or DSS session can be in the up state unless the network
@@ -280,7 +289,7 @@ device.
 
 Tip: It might be less confusing to the end user to name this VLAN
 subdevice after the MBIM SessionID instead of the VLAN ID.  For
-example:
+example::
 
   ip link add link wwan0 name wwan0.0 type vlan id 4094
 
@@ -290,7 +299,7 @@ VLAN mapping
 
 Summarizing the cdc_mbim driver mapping described above, we have this
 relationship between VLAN tags on the wwanY network device and MBIM
-sessions on the shared USB data channel:
+sessions on the shared USB data channel::
 
   VLAN ID       MBIM type   MBIM SessionID           Notes
   ---------------------------------------------------------
@@ -310,30 +319,37 @@ sessions on the shared USB data channel:
 References
 ==========
 
-[1] USB Implementers Forum, Inc. - "Universal Serial Bus
-      Communications Class Subclass Specification for Mobile Broadband
-      Interface Model", Revision 1.0 (Errata 1), May 1, 2013
+ 1) USB Implementers Forum, Inc. - "Universal Serial Bus
+    Communications Class Subclass Specification for Mobile Broadband
+    Interface Model", Revision 1.0 (Errata 1), May 1, 2013
+
       - http://www.usb.org/developers/docs/devclass_docs/
 
-[2] USB Implementers Forum, Inc. - "Universal Serial Bus
-      Communications Class Subclass Specifications for Network Control
-      Model Devices", Revision 1.0 (Errata 1), November 24, 2010
+ 2) USB Implementers Forum, Inc. - "Universal Serial Bus
+    Communications Class Subclass Specifications for Network Control
+    Model Devices", Revision 1.0 (Errata 1), November 24, 2010
+
       - http://www.usb.org/developers/docs/devclass_docs/
 
-[3] libmbim - "a glib-based library for talking to WWAN modems and
-      devices which speak the Mobile Interface Broadband Model (MBIM)
-      protocol"
+ 3) libmbim - "a glib-based library for talking to WWAN modems and
+    devices which speak the Mobile Interface Broadband Model (MBIM)
+    protocol"
+
       - http://www.freedesktop.org/wiki/Software/libmbim/
 
-[4] ModemManager - "a DBus-activated daemon which controls mobile
-      broadband (2G/3G/4G) devices and connections"
+ 4) ModemManager - "a DBus-activated daemon which controls mobile
+    broadband (2G/3G/4G) devices and connections"
+
       - http://www.freedesktop.org/wiki/Software/ModemManager/
 
-[5] "MBIM (Mobile Broadband Interface Model) Registry"
+ 5) "MBIM (Mobile Broadband Interface Model) Registry"
+
        - http://compliance.usb.org/mbim/
 
-[6] "/sys/kernel/debug/usb/devices output format"
+ 6) "/sys/kernel/debug/usb/devices output format"
+
        - Documentation/driver-api/usb/usb.rst
 
-[7] "/sys/bus/usb/devices/.../descriptors"
+ 7) "/sys/bus/usb/devices/.../descriptors"
+
        - Documentation/ABI/stable/sysfs-bus-usb
Documentation/networking/index.rst +1 -0
index 22b872834ef0..55802abd65a0 100644
@@ -45,6 +45,7 @@ Contents:
    ax25
    baycom
    bonding
+   cdc_mbim
 
 .. only::  subproject and html
 
Signature · 1 line
2.25.4
#11 lore raw

PATCH 11/38 docs: networking: convert cops.txt to ReST

In reply to Mauro Carvalho Chehab

- add SPDX header;
- adjust titles and chapters, adding proper markups;
- mark code blocks and literals as such;
- adjust identation, whitespaces and blank lines;
- add to networking/index.rst.

---
 Documentation/networking/cops.rst  | 80 ++++++++++++++++++++++++++++++
 Documentation/networking/cops.txt  | 63 -----------------------
 Documentation/networking/index.rst |  1 +
 drivers/net/appletalk/Kconfig      |  2 +-
 4 files changed, 82 insertions(+), 64 deletions(-)
 create mode 100644 Documentation/networking/cops.rst
 delete mode 100644 Documentation/networking/cops.txt
Documentation/networking/cops.rst new file +80 -0
new file mode 100644
index 000000000000..964ba80599a9
@@ -0,0 +1,80 @@
+.. SPDX-License-Identifier: GPL-2.0
+
+========================================
+The COPS LocalTalk Linux driver (cops.c)
+========================================
+
+By Jay Schulist <[email protected]>
+
+This driver has two modes and they are: Dayna mode and Tangent mode.
+Each mode corresponds with the type of card. It has been found
+that there are 2 main types of cards and all other cards are
+the same and just have different names or only have minor differences
+such as more IO ports. As this driver is tested it will
+become more clear exactly what cards are supported.
+
+Right now these cards are known to work with the COPS driver. The
+LT-200 cards work in a somewhat more limited capacity than the
+DL200 cards, which work very well and are in use by many people.
+
+TANGENT driver mode:
+	- Tangent ATB-II, Novell NL-1000, Daystar Digital LT-200
+
+DAYNA driver mode:
+	- Dayna DL2000/DaynaTalk PC (Half Length), COPS LT-95,
+	- Farallon PhoneNET PC III, Farallon PhoneNET PC II
+
+Other cards possibly supported mode unknown though:
+	- Dayna DL2000 (Full length)
+
+The COPS driver defaults to using Dayna mode. To change the driver's
+mode if you built a driver with dual support use board_type=1 or
+board_type=2 for Dayna or Tangent with insmod.
+
+Operation/loading of the driver
+===============================
+
+Use modprobe like this:	/sbin/modprobe cops.o (IO #) (IRQ #)
+If you do not specify any options the driver will try and use the IO = 0x240,
+IRQ = 5. As of right now I would only use IRQ 5 for the card, if autoprobing.
+
+To load multiple COPS driver Localtalk cards you can do one of the following::
+
+	insmod cops io=0x240 irq=5
+	insmod -o cops2 cops io=0x260 irq=3
+
+Or in lilo.conf put something like this::
+
+	append="ether=5,0x240,lt0 ether=3,0x260,lt1"
+
+Then bring up the interface with ifconfig. It will look something like this::
+
+  lt0       Link encap:UNSPEC  HWaddr 00-00-00-00-00-00-00-F7-00-00-00-00-00-00-00-00
+	    inet addr:192.168.1.2  Bcast:192.168.1.255  Mask:255.255.255.0
+	    UP BROADCAST RUNNING NOARP MULTICAST  MTU:600  Metric:1
+	    RX packets:0 errors:0 dropped:0 overruns:0 frame:0
+	    TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 coll:0
+
+Netatalk Configuration
+======================
+
+You will need to configure atalkd with something like the following to make
+it work with the cops.c driver.
+
+* For single LTalk card use::
+
+    dummy -seed -phase 2 -net 2000 -addr 2000.10 -zone "1033"
+    lt0 -seed -phase 1 -net 1000 -addr 1000.50 -zone "1033"
+
+* For multiple cards, Ethernet and LocalTalk::
+
+    eth0 -seed -phase 2 -net 3000 -addr 3000.20 -zone "1033"
+    lt0 -seed -phase 1 -net 1000 -addr 1000.50 -zone "1033"
+
+* For multiple LocalTalk cards, and an Ethernet card.
+
+* Order seems to matter here, Ethernet last::
+
+    lt0 -seed -phase 1 -net 1000 -addr 1000.10 -zone "LocalTalk1"
+    lt1 -seed -phase 1 -net 2000 -addr 2000.20 -zone "LocalTalk2"
+    eth0 -seed -phase 2 -net 3000 -addr 3000.30 -zone "EtherTalk"
Documentation/networking/cops.txt deleted +0 -63

63 lines not on this page · raw message

Documentation/networking/index.rst +1 -0
index 55802abd65a0..7b596810d479 100644
@@ -46,6 +46,7 @@ Contents:
    baycom
    bonding
    cdc_mbim
+   cops
 
 .. only::  subproject and html
 
drivers/net/appletalk/Kconfig +1 -1
index af509b05ac5c..d4e51c048f62 100644
@@ -59,7 +59,7 @@ config COPS
 	  package. This driver is experimental, which means that it may not
 	  work. This driver will only work if you choose "AppleTalk DDP"
 	  networking support, above.
-	  Please read the file <file:Documentation/networking/cops.txt>.
+	  Please read the file <file:Documentation/networking/cops.rst>.
 
 config COPS_DAYNA
 	bool "Dayna firmware support"
Signature · 1 line
2.25.4
#12 lore raw

PATCH 12/38 docs: networking: convert cxacru.txt to ReST

In reply to Mauro Carvalho Chehab

- add SPDX header;
- add a document title;
- mark code blocks and literals as such;
- mark lists as such;
- adjust identation, whitespaces and blank lines;
- add to networking/index.rst.

---
 .../networking/{cxacru.txt => cxacru.rst}     | 86 ++++++++++++-------
 Documentation/networking/index.rst            |  1 +
 2 files changed, 54 insertions(+), 33 deletions(-)
 rename Documentation/networking/{cxacru.txt => cxacru.rst} (66%)
Documentation/networking/cxacru.rst renamed from Documentation/networking/cxacru.txt +53 -33
similarity index 66%
rename from Documentation/networking/cxacru.txt
rename to Documentation/networking/cxacru.rst
index 2cce04457b4d..6088af2ffeda 100644
@@ -1,3 +1,9 @@
+.. SPDX-License-Identifier: GPL-2.0
+
+========================
+ATM cxacru device driver
+========================
+
 Firmware is required for this device: http://accessrunner.sourceforge.net/
 
 While it is capable of managing/maintaining the ADSL connection without the
@@ -19,29 +25,35 @@ several sysfs attribute files for retrieving device statistics:
 
 * adsl_headend
 * adsl_headend_environment
-	Information about the remote headend.
+
+	- Information about the remote headend.
 
 * adsl_config
-	Configuration writing interface.
-	Write parameters in hexadecimal format <index>=<value>,
-	separated by whitespace, e.g.:
+
+	- Configuration writing interface.
+	- Write parameters in hexadecimal format <index>=<value>,
+	  separated by whitespace, e.g.:
+
 		"1=0 a=5"
-	Up to 7 parameters at a time will be sent and the modem will restart
-	the ADSL connection when any value is set. These are logged for future
-	reference.
+
+	- Up to 7 parameters at a time will be sent and the modem will restart
+	  the ADSL connection when any value is set. These are logged for future
+	  reference.
 
 * downstream_attenuation (dB)
 * downstream_bits_per_frame
 * downstream_rate (kbps)
 * downstream_snr_margin (dB)
-	Downstream stats.
+
+	- Downstream stats.
 
 * upstream_attenuation (dB)
 * upstream_bits_per_frame
 * upstream_rate (kbps)
 * upstream_snr_margin (dB)
 * transmitter_power (dBm/Hz)
-	Upstream stats.
+
+	- Upstream stats.
 
 * downstream_crc_errors
 * downstream_fec_errors
@@ -49,48 +61,56 @@ several sysfs attribute files for retrieving device statistics:
 * upstream_crc_errors
 * upstream_fec_errors
 * upstream_hec_errors
-	Error counts.
+
+	- Error counts.
 
 * line_startable
-	Indicates that ADSL support on the device
-	is/can be enabled, see adsl_start.
+
+	- Indicates that ADSL support on the device
+	  is/can be enabled, see adsl_start.
 
 * line_status
-	"initialising"
-	"down"
-	"attempting to activate"
-	"training"
-	"channel analysis"
-	"exchange"
-	"waiting"
-	"up"
+
+	 - "initialising"
+	 - "down"
+	 - "attempting to activate"
+	 - "training"
+	 - "channel analysis"
+	 - "exchange"
+	 - "waiting"
+	 - "up"
 
 	Changes between "down" and "attempting to activate"
 	if there is no signal.
 
 * link_status
-	"not connected"
-	"connected"
-	"lost"
+
+	 - "not connected"
+	 - "connected"
+	 - "lost"
 
 * mac_address
 
 * modulation
-	"" (when not connected)
-	"ANSI T1.413"
-	"ITU-T G.992.1 (G.DMT)"
-	"ITU-T G.992.2 (G.LITE)"
+
+	 - "" (when not connected)
+	 - "ANSI T1.413"
+	 - "ITU-T G.992.1 (G.DMT)"
+	 - "ITU-T G.992.2 (G.LITE)"
 
 * startup_attempts
-	Count of total attempts to initialise ADSL.
+
+	- Count of total attempts to initialise ADSL.
 
 To enable/disable ADSL, the following can be written to the adsl_state file:
-	"start"
-	"stop
-	"restart" (stops, waits 1.5s, then starts)
-	"poll" (used to resume status polling if it was disabled due to failure)
 
-Changes in adsl/line state are reported via kernel log messages:
+	 - "start"
+	 - "stop
+	 - "restart" (stops, waits 1.5s, then starts)
+	 - "poll" (used to resume status polling if it was disabled due to failure)
+
+Changes in adsl/line state are reported via kernel log messages::
+
 	[4942145.150704] ATM dev 0: ADSL state: running
 	[4942243.663766] ATM dev 0: ADSL line: down
 	[4942249.665075] ATM dev 0: ADSL line: attempting to activate
Documentation/networking/index.rst +1 -0
index 7b596810d479..4c8e896490e0 100644
@@ -47,6 +47,7 @@ Contents:
    bonding
    cdc_mbim
    cops
+   cxacru
 
 .. only::  subproject and html
 
Signature · 1 line
2.25.4
#13 lore raw

PATCH 13/38 docs: networking: convert dccp.txt to ReST

In reply to Mauro Carvalho Chehab

- add SPDX header;
- adjust title markup;
- comment out text-only TOC from html/pdf output;
- mark code blocks and literals as such;
- adjust identation, whitespaces and blank lines;
- add to networking/index.rst.

---
 .../networking/{dccp.txt => dccp.rst}         | 39 ++++++++++++-------
 Documentation/networking/index.rst            |  1 +
 2 files changed, 25 insertions(+), 15 deletions(-)
 rename Documentation/networking/{dccp.txt => dccp.rst} (94%)
Documentation/networking/dccp.rst renamed from Documentation/networking/dccp.txt +24 -15
similarity index 94%
rename from Documentation/networking/dccp.txt
rename to Documentation/networking/dccp.rst
index 55c575fcaf17..dde16be04456 100644
@@ -1,16 +1,18 @@
+.. SPDX-License-Identifier: GPL-2.0
+
+=============
 DCCP protocol
 =============
 
 
-Contents
-========
-- Introduction
-- Missing features
-- Socket options
-- Sysctl variables
-- IOCTLs
-- Other tunables
-- Notes
+.. Contents
+   - Introduction
+   - Missing features
+   - Socket options
+   - Sysctl variables
+   - IOCTLs
+   - Other tunables
+   - Notes
 
 
 Introduction
@@ -38,6 +40,7 @@ The Linux DCCP implementation does not currently support all the features that a
 specified in RFCs 4340...42.
 
 The known bugs are at:
+
 	http://www.linuxfoundation.org/collaborate/workgroups/networking/todo#DCCP
 
 For more up-to-date versions of the DCCP implementation, please consider using
@@ -54,7 +57,8 @@ defined: the "simple" policy (DCCPQ_POLICY_SIMPLE), which does nothing special,
 and a priority-based variant (DCCPQ_POLICY_PRIO). The latter allows to pass an
 u32 priority value as ancillary data to sendmsg(), where higher numbers indicate
 a higher packet priority (similar to SO_PRIORITY). This ancillary data needs to
-be formatted using a cmsg(3) message header filled in as follows:
+be formatted using a cmsg(3) message header filled in as follows::
+
 	cmsg->cmsg_level = SOL_DCCP;
 	cmsg->cmsg_type	 = DCCP_SCM_PRIORITY;
 	cmsg->cmsg_len	 = CMSG_LEN(sizeof(uint32_t));	/* or CMSG_LEN(4) */
@@ -94,7 +98,7 @@ must be registered on the socket before calling connect() or listen().
 
 DCCP_SOCKOPT_TX_CCID is read/write. It returns the current CCID (if set) or sets
 the preference list for the TX CCID, using the same format as DCCP_SOCKOPT_CCID.
-Please note that the getsockopt argument type here is `int', not uint8_t.
+Please note that the getsockopt argument type here is ``int``, not uint8_t.
 
 DCCP_SOCKOPT_RX_CCID is analogous to DCCP_SOCKOPT_TX_CCID, but for the RX CCID.
 
@@ -113,6 +117,7 @@ be enabled at the receiver, too with suitable choice of CsCov.
 DCCP_SOCKOPT_SEND_CSCOV sets the sender checksum coverage. Values in the
 	range 0..15 are acceptable. The default setting is 0 (full coverage),
 	values between 1..15 indicate partial coverage.
+
 DCCP_SOCKOPT_RECV_CSCOV is for the receiver and has a different meaning: it
 	sets a threshold, where again values 0..15 are acceptable. The default
 	of 0 means that all packets with a partial coverage will be discarded.
@@ -123,11 +128,13 @@ DCCP_SOCKOPT_RECV_CSCOV is for the receiver and has a different meaning: it
 
 The following two options apply to CCID 3 exclusively and are getsockopt()-only.
 In either case, a TFRC info struct (defined in <linux/tfrc.h>) is returned.
+
 DCCP_SOCKOPT_CCID_RX_INFO
-	Returns a `struct tfrc_rx_info' in optval; the buffer for optval and
+	Returns a ``struct tfrc_rx_info`` in optval; the buffer for optval and
 	optlen must be set to at least sizeof(struct tfrc_rx_info).
+
 DCCP_SOCKOPT_CCID_TX_INFO
-	Returns a `struct tfrc_tx_info' in optval; the buffer for optval and
+	Returns a ``struct tfrc_tx_info`` in optval; the buffer for optval and
 	optlen must be set to at least sizeof(struct tfrc_tx_info).
 
 On unidirectional connections it is useful to close the unused half-connection
@@ -182,7 +189,7 @@ sync_ratelimit = 125 ms
 IOCTLS
 ======
 FIONREAD
-	Works as in udp(7): returns in the `int' argument pointer the size of
+	Works as in udp(7): returns in the ``int`` argument pointer the size of
 	the next pending datagram in bytes, or 0 when no datagram is pending.
 
 
@@ -191,10 +198,12 @@ Other tunables
 Per-route rto_min support
 	CCID-2 supports the RTAX_RTO_MIN per-route setting for the minimum value
 	of the RTO timer. This setting can be modified via the 'rto_min' option
-	of iproute2; for example:
+	of iproute2; for example::
+
 		> ip route change 10.0.0.0/24   rto_min 250j dev wlan0
 		> ip route add    10.0.0.254/32 rto_min 800j dev wlan0
 		> ip route show dev wlan0
+
 	CCID-3 also supports the rto_min setting: it is used to define the lower
 	bound for the expiry of the nofeedback timer. This can be useful on LANs
 	with very low RTTs (e.g., loopback, Gbit ethernet).
Documentation/networking/index.rst +1 -0
index 4c8e896490e0..3894043332de 100644
@@ -48,6 +48,7 @@ Contents:
    cdc_mbim
    cops
    cxacru
+   dccp
 
 .. only::  subproject and html
 
Signature · 1 line
2.25.4
#14 lore raw

PATCH 14/38 docs: networking: convert dctcp.txt to ReST

In reply to Mauro Carvalho Chehab

- add SPDX header;
- adjust title markup;
- mark code blocks and literals as such;
- adjust identation, whitespaces and blank lines;
- add to networking/index.rst.

---
 Documentation/networking/{dctcp.txt => dctcp.rst} | 14 +++++++++++---
 Documentation/networking/index.rst                |  1 +
 2 files changed, 12 insertions(+), 3 deletions(-)
 rename Documentation/networking/{dctcp.txt => dctcp.rst} (89%)
Documentation/networking/dctcp.rst renamed from Documentation/networking/dctcp.txt +11 -3
similarity index 89%
rename from Documentation/networking/dctcp.txt
rename to Documentation/networking/dctcp.rst
index 13a857753208..4cc8bb2dad50 100644
@@ -1,11 +1,14 @@
+.. SPDX-License-Identifier: GPL-2.0
+
+======================
 DCTCP (DataCenter TCP)
-----------------------
+======================
 
 DCTCP is an enhancement to the TCP congestion control algorithm for data
 center networks and leverages Explicit Congestion Notification (ECN) in
 the data center network to provide multi-bit feedback to the end hosts.
 
-To enable it on end hosts:
+To enable it on end hosts::
 
   sysctl -w net.ipv4.tcp_congestion_control=dctcp
   sysctl -w net.ipv4.tcp_ecn_fallback=0 (optional)
@@ -25,14 +28,19 @@ SIGCOMM/SIGMETRICS papers:
 
  i) Mohammad Alizadeh, Albert Greenberg, David A. Maltz, Jitendra Padhye,
     Parveen Patel, Balaji Prabhakar, Sudipta Sengupta, and Murari Sridharan:
-      "Data Center TCP (DCTCP)", Data Center Networks session
+
+      "Data Center TCP (DCTCP)", Data Center Networks session"
+
       Proc. ACM SIGCOMM, New Delhi, 2010.
+
     http://simula.stanford.edu/~alizade/Site/DCTCP_files/dctcp-final.pdf
     http://www.sigcomm.org/ccr/papers/2010/October/1851275.1851192
 
 ii) Mohammad Alizadeh, Adel Javanmard, and Balaji Prabhakar:
+
       "Analysis of DCTCP: Stability, Convergence, and Fairness"
       Proc. ACM SIGMETRICS, San Jose, 2011.
+
     http://simula.stanford.edu/~alizade/Site/DCTCP_files/dctcp_analysis-full.pdf
 
 IETF informational draft:
Documentation/networking/index.rst +1 -0
index 3894043332de..9e83d3bda4e0 100644
@@ -49,6 +49,7 @@ Contents:
    cops
    cxacru
    dccp
+   dctcp
 
 .. only::  subproject and html
 
Signature · 1 line
2.25.4
#15 lore raw

PATCH 15/38 docs: networking: convert decnet.txt to ReST

In reply to Mauro Carvalho Chehab

- add SPDX header;
- adjust titles and chapters, adding proper markups;
- mark lists as such;
- mark code blocks and literals as such;
- adjust identation, whitespaces and blank lines;
- add to networking/index.rst.

---
 .../admin-guide/kernel-parameters.txt         |  2 +-
 .../networking/{decnet.txt => decnet.rst}     | 77 +++++++++++--------
 Documentation/networking/index.rst            |  1 +
 MAINTAINERS                                   |  2 +-
 net/decnet/Kconfig                            |  4 +-
 5 files changed, 50 insertions(+), 36 deletions(-)
 rename Documentation/networking/{decnet.txt => decnet.rst} (87%)
Documentation/admin-guide/kernel-parameters.txt +1 -1
index 942e7f59a356..cd68635370c6 100644
@@ -831,7 +831,7 @@
 
 	decnet.addr=	[HW,NET]
 			Format: <area>[,<node>]
-			See also Documentation/networking/decnet.txt.
+			See also Documentation/networking/decnet.rst.
 
 	default_hugepagesz=
 			[HW] The size of the default HugeTLB page. This is
Documentation/networking/decnet.rst renamed from Documentation/networking/decnet.txt +45 -32

180 lines not on this page · raw message

Documentation/networking/index.rst +1 -0
index 9e83d3bda4e0..e17432492745 100644
@@ -50,6 +50,7 @@ Contents:
    cxacru
    dccp
    dctcp
+   decnet
 
 .. only::  subproject and html
 
MAINTAINERS +1 -1
index a1558eb34c45..f5214418cc19 100644
@@ -4739,7 +4739,7 @@ DECnet NETWORK LAYER
 L:	[email protected]
 S:	Orphan
 W:	http://linux-decnet.sourceforge.net
-F:	Documentation/networking/decnet.txt
+F:	Documentation/networking/decnet.rst
 F:	net/decnet/
 
 DECSTATION PLATFORM SUPPORT
net/decnet/Kconfig +2 -2
index 0935453ccfd5..8f98fb2f2ec9 100644
@@ -15,7 +15,7 @@ config DECNET
 	  <http://linux-decnet.sourceforge.net/>.
 
 	  More detailed documentation is available in
-	  <file:Documentation/networking/decnet.txt>.
+	  <file:Documentation/networking/decnet.rst>.
 
 	  Be sure to say Y to "/proc file system support" and "Sysctl support"
 	  below when using DECnet, since you will need sysctl support to aid
@@ -40,4 +40,4 @@ config DECNET_ROUTER
 	  filtering" option will be required for the forthcoming routing daemon
 	  to work.
 
-	  See <file:Documentation/networking/decnet.txt> for more information.
+	  See <file:Documentation/networking/decnet.rst> for more information.
Signature · 1 line
2.25.4
#16 lore raw

PATCH 16/38 docs: networking: convert defza.txt to ReST

In reply to Mauro Carvalho Chehab

Not much to be done here:

- add SPDX header;
- add a document title;
- use :field: markup for the version number;
- add to networking/index.rst.

---
 Documentation/networking/{defza.txt => defza.rst} | 8 +++++++-
 Documentation/networking/index.rst                | 1 +
 2 files changed, 8 insertions(+), 1 deletion(-)
 rename Documentation/networking/{defza.txt => defza.rst} (91%)
Documentation/networking/defza.rst renamed from Documentation/networking/defza.txt +7 -1
similarity index 91%
rename from Documentation/networking/defza.txt
rename to Documentation/networking/defza.rst
index 663e4a906751..73c2f793ea26 100644
@@ -1,4 +1,10 @@
-Notes on the DEC FDDIcontroller 700 (DEFZA-xx) driver v.1.1.4.
+.. SPDX-License-Identifier: GPL-2.0
+
+=====================================================
+Notes on the DEC FDDIcontroller 700 (DEFZA-xx) driver
+=====================================================
+
+:Version: v.1.1.4
 
 
 DEC FDDIcontroller 700 is DEC's first-generation TURBOchannel FDDI
Documentation/networking/index.rst +1 -0
index e17432492745..c893127004b9 100644
@@ -51,6 +51,7 @@ Contents:
    dccp
    dctcp
    decnet
+   defza
 
 .. only::  subproject and html
 
Signature · 1 line
2.25.4
#17 lore raw

PATCH 17/38 docs: networking: convert dns_resolver.txt to ReST

In reply to Mauro Carvalho Chehab

- add SPDX header;
- adjust titles and chapters, adding proper markups;
- comment out text-only TOC from html/pdf output;

- mark code blocks and literals as such;

- adjust identation, whitespaces and blank lines;
- add to networking/index.rst.

---
 .../{dns_resolver.txt => dns_resolver.rst}    | 52 +++++++++----------
 Documentation/networking/index.rst            |  1 +
 net/ceph/Kconfig                              |  2 +-
 net/dns_resolver/Kconfig                      |  2 +-
 net/dns_resolver/dns_key.c                    |  2 +-
 net/dns_resolver/dns_query.c                  |  2 +-
 6 files changed, 30 insertions(+), 31 deletions(-)
 rename Documentation/networking/{dns_resolver.txt => dns_resolver.rst} (89%)
Documentation/networking/dns_resolver.rst renamed from Documentation/networking/dns_resolver.txt +25 -27
similarity index 89%
rename from Documentation/networking/dns_resolver.txt
rename to Documentation/networking/dns_resolver.rst
index eaa8f9a6fd5d..add4d59a99a5 100644
@@ -1,8 +1,10 @@
-			     ===================
-			     DNS Resolver Module
-			     ===================
+.. SPDX-License-Identifier: GPL-2.0
 
-Contents:
+===================
+DNS Resolver Module
+===================
+
+.. Contents:
 
  - Overview.
  - Compilation.
@@ -12,8 +14,7 @@ Contents:
  - Debugging.
 
 
-========
-OVERVIEW
+Overview
 ========
 
 The DNS resolver module provides a way for kernel services to make DNS queries
@@ -33,50 +34,50 @@ It does not yet support the following AFS features:
 This code is extracted from the CIFS filesystem.
 
 
-===========
-COMPILATION
+Compilation
 ===========
 
-The module should be enabled by turning on the kernel configuration options:
+The module should be enabled by turning on the kernel configuration options::
 
 	CONFIG_DNS_RESOLVER	- tristate "DNS Resolver support"
 
 
-==========
-SETTING UP
+Setting up
 ==========
 
 To set up this facility, the /etc/request-key.conf file must be altered so that
 /sbin/request-key can appropriately direct the upcalls.  For example, to handle
 basic dname to IPv4/IPv6 address resolution, the following line should be
-added:
+added::
+
 
 	#OP	TYPE		DESC	CO-INFO	PROGRAM ARG1 ARG2 ARG3 ...
 	#======	============	=======	=======	==========================
 	create	dns_resolver  	*	*	/usr/sbin/cifs.upcall %k
 
 To direct a query for query type 'foo', a line of the following should be added
-before the more general line given above as the first match is the one taken.
+before the more general line given above as the first match is the one taken::
 
 	create	dns_resolver  	foo:*	*	/usr/sbin/dns.foo %k
 
 
-=====
-USAGE
+Usage
 =====
 
 To make use of this facility, one of the following functions that are
-implemented in the module can be called after doing:
+implemented in the module can be called after doing::
 
 	#include <linux/dns_resolver.h>
 
- (1) int dns_query(const char *type, const char *name, size_t namelen,
-		   const char *options, char **_result, time_t *_expiry);
+     ::
+
+	int dns_query(const char *type, const char *name, size_t namelen,
+		     const char *options, char **_result, time_t *_expiry);
 
      This is the basic access function.  It looks for a cached DNS query and if
      it doesn't find it, it upcalls to userspace to make a new DNS query, which
      may then be cached.  The key description is constructed as a string of the
-     form:
+     form::
 
 		[<type>:]<name>
 
@@ -107,16 +108,14 @@ This can be cleared by any process that has the CAP_SYS_ADMIN capability by
 the use of KEYCTL_KEYRING_CLEAR on the keyring ID.
 
 
-===============================
-READING DNS KEYS FROM USERSPACE
+Reading DNS Keys from Userspace
 ===============================
 
 Keys of dns_resolver type can be read from userspace using keyctl_read() or
 "keyctl read/print/pipe".
 
 
-=========
-MECHANISM
+Mechanism
 =========
 
 The dnsresolver module registers a key type called "dns_resolver".  Keys of
@@ -147,11 +146,10 @@ See <file:Documentation/security/keys/request-key.rst> for further
 information about request-key function.
 
 
-=========
-DEBUGGING
+Debugging
 =========
 
 Debugging messages can be turned on dynamically by writing a 1 into the
-following file:
+following file::
 
-        /sys/module/dnsresolver/parameters/debug
+	/sys/module/dnsresolver/parameters/debug
Documentation/networking/index.rst +1 -0
index c893127004b9..55746038a7e9 100644
@@ -52,6 +52,7 @@ Contents:
    dctcp
    decnet
    defza
+   dns_resolver
 
 .. only::  subproject and html
 
net/ceph/Kconfig +1 -1
index 2e8e6f904920..d7bec7adc267 100644
@@ -39,6 +39,6 @@ config CEPH_LIB_USE_DNS_RESOLVER
 	  be resolved using the CONFIG_DNS_RESOLVER facility.
 
 	  For information on how to use CONFIG_DNS_RESOLVER consult
-	  Documentation/networking/dns_resolver.txt
+	  Documentation/networking/dns_resolver.rst
 
 	  If unsure, say N.
net/dns_resolver/Kconfig +1 -1
index 0a1c2238b4bd..255df9b6e9e8 100644
@@ -19,7 +19,7 @@ config DNS_RESOLVER
 	  SMB2 later.  DNS Resolver is supported by the userspace upcall
 	  helper "/sbin/dns.resolver" via /etc/request-key.conf.
 
-	  See <file:Documentation/networking/dns_resolver.txt> for further
+	  See <file:Documentation/networking/dns_resolver.rst> for further
 	  information.
 
 	  To compile this as a module, choose M here: the module will be called
net/dns_resolver/dns_key.c +1 -1
index ad53eb31d40f..3aced951d5ab 100644
@@ -1,6 +1,6 @@
 /* Key type used to cache DNS lookups made by the kernel
  *
- * See Documentation/networking/dns_resolver.txt
+ * See Documentation/networking/dns_resolver.rst
  *
  *   Copyright (c) 2007 Igor Mammedov
  *   Author(s): Igor Mammedov ([email protected])
net/dns_resolver/dns_query.c +1 -1
index cab4e0df924f..82b084cc1cc6 100644
@@ -1,7 +1,7 @@
 /* Upcall routine, designed to work as a key type and working through
  * /sbin/request-key to contact userspace when handling DNS queries.
  *
- * See Documentation/networking/dns_resolver.txt
+ * See Documentation/networking/dns_resolver.rst
  *
  *   Copyright (c) 2007 Igor Mammedov
  *   Author(s): Igor Mammedov ([email protected])
Signature · 1 line
2.25.4
#18 lore raw

PATCH 18/38 docs: networking: convert driver.txt to ReST

In reply to Mauro Carvalho Chehab

- add SPDX header;
- add a document title;
- mark code blocks and literals as such;
- adjust identation, whitespaces and blank lines;
- add to networking/index.rst.

---
 .../networking/{driver.txt => driver.rst}     | 22 +++++++++++--------
 Documentation/networking/index.rst            |  1 +
 2 files changed, 14 insertions(+), 9 deletions(-)
 rename Documentation/networking/{driver.txt => driver.rst} (85%)
Documentation/networking/driver.rst renamed from Documentation/networking/driver.txt +13 -9
similarity index 85%
rename from Documentation/networking/driver.txt
rename to Documentation/networking/driver.rst
index da59e2884130..c8f59dbda46f 100644
@@ -1,4 +1,8 @@
-Document about softnet driver issues
+.. SPDX-License-Identifier: GPL-2.0
+
+=====================
+Softnet Driver Issues
+=====================
 
 Transmit path guidelines:
 
@@ -8,7 +12,7 @@ Transmit path guidelines:
    transmit function will become busy.
 
    Instead it must maintain the queue properly.  For example,
-   for a driver implementing scatter-gather this means:
+   for a driver implementing scatter-gather this means::
 
 	static netdev_tx_t drv_hard_start_xmit(struct sk_buff *skb,
 					       struct net_device *dev)
@@ -38,25 +42,25 @@ Transmit path guidelines:
 		return NETDEV_TX_OK;
 	}
 
-   And then at the end of your TX reclamation event handling:
+   And then at the end of your TX reclamation event handling::
 
 	if (netif_queue_stopped(dp->dev) &&
-            TX_BUFFS_AVAIL(dp) > (MAX_SKB_FRAGS + 1))
+	    TX_BUFFS_AVAIL(dp) > (MAX_SKB_FRAGS + 1))
 		netif_wake_queue(dp->dev);
 
-   For a non-scatter-gather supporting card, the three tests simply become:
+   For a non-scatter-gather supporting card, the three tests simply become::
 
 		/* This is a hard error log it. */
 		if (TX_BUFFS_AVAIL(dp) <= 0)
 
-   and:
+   and::
 
 		if (TX_BUFFS_AVAIL(dp) == 0)
 
-   and:
+   and::
 
 	if (netif_queue_stopped(dp->dev) &&
-            TX_BUFFS_AVAIL(dp) > 0)
+	    TX_BUFFS_AVAIL(dp) > 0)
 		netif_wake_queue(dp->dev);
 
 2) An ndo_start_xmit method must not modify the shared parts of a
@@ -86,7 +90,7 @@ Close/stop guidelines:
 
 1) After the ndo_stop routine has been called, the hardware must
    not receive or transmit any data.  All in flight packets must
-   be aborted. If necessary, poll or wait for completion of 
+   be aborted. If necessary, poll or wait for completion of
    any reset commands.
 
 2) The ndo_stop routine will be called by unregister_netdevice
Documentation/networking/index.rst +1 -0
index 55746038a7e9..313f66900bce 100644
@@ -53,6 +53,7 @@ Contents:
    decnet
    defza
    dns_resolver
+   driver
 
 .. only::  subproject and html
 
Signature · 1 line
2.25.4
#19 lore raw

PATCH 19/38 docs: networking: convert eql.txt to ReST

In reply to Mauro Carvalho Chehab

- add SPDX header;
- add a document title;
- adjust titles and chapters, adding proper markups;
- mark code blocks and literals as such;
- mark tables as such;
- adjust identation, whitespaces and blank lines;
- add to networking/index.rst.

---
 Documentation/networking/{eql.txt => eql.rst} | 445 ++++++------------
 Documentation/networking/index.rst            |   1 +
 drivers/net/Kconfig                           |   2 +-
 3 files changed, 147 insertions(+), 301 deletions(-)
 rename Documentation/networking/{eql.txt => eql.rst} (62%)
Documentation/networking/eql.rst renamed from Documentation/networking/eql.txt +145 -300
similarity index 62%
rename from Documentation/networking/eql.txt
rename to Documentation/networking/eql.rst
index 0f1550150f05..a628c4c81166 100644
@@ -1,5 +1,11 @@
-  EQL Driver: Serial IP Load Balancing HOWTO
+.. SPDX-License-Identifier: GPL-2.0
+
+==========================================
+EQL Driver: Serial IP Load Balancing HOWTO
+==========================================
+
   Simon "Guru Aleph-Null" Janes, [email protected]
+
   v1.1, February 27, 1995
 
   This is the manual for the EQL device driver. EQL is a software device
@@ -12,7 +18,8 @@
   which was only created to patch cleanly in the very latest kernel
   source trees. (Yes, it worked fine.)
 
-  1.  Introduction
+1. Introduction
+===============
 
   Which is worse? A huge fee for a 56K leased line or two phone lines?
   It's probably the former.  If you find yourself craving more bandwidth,
@@ -41,47 +48,40 @@
   Hey, we can all dream you know...
 
 
-  2.  Kernel Configuration
+2. Kernel Configuration
+=======================
 
   Here I describe the general steps of getting a kernel up and working
   with the eql driver.	From patching, building, to installing.
 
 
-  2.1.	Patching The Kernel
+2.1. Patching The Kernel
+------------------------
 
   If you do not have or cannot get a copy of the kernel with the eql
   driver folded into it, get your copy of the driver from
   ftp://slaughter.ncm.com/pub/Linux/LOAD_BALANCING/eql-1.1.tar.gz.
   Unpack this archive someplace obvious like /usr/local/src/.  It will
-  create the following files:
+  create the following files::
 
-
-
-       ______________________________________________________________________
        -rw-r--r-- guru/ncm	198 Jan 19 18:53 1995 eql-1.1/NO-WARRANTY
        -rw-r--r-- guru/ncm	30620 Feb 27 21:40 1995 eql-1.1/eql-1.1.patch
        -rwxr-xr-x guru/ncm	16111 Jan 12 22:29 1995 eql-1.1/eql_enslave
        -rw-r--r-- guru/ncm	2195 Jan 10 21:48 1995 eql-1.1/eql_enslave.c
-       ______________________________________________________________________
 
   Unpack a recent kernel (something after 1.1.92) someplace convenient
   like say /usr/src/linux-1.1.92.eql. Use symbolic links to point
   /usr/src/linux to this development directory.
 
 
-  Apply the patch by running the commands:
+  Apply the patch by running the commands::
 
-
-       ______________________________________________________________________
        cd /usr/src
        patch </usr/local/src/eql-1.1/eql-1.1.patch
-       ______________________________________________________________________
 
 
-
-
-
-  2.2.	Building The Kernel
+2.2. Building The Kernel
+------------------------
 
   After patching the kernel, run make config and configure the kernel
   for your hardware.
@@ -90,7 +90,8 @@
   After configuration, make and install according to your habit.
 
 
-  3.  Network Configuration
+3. Network Configuration
+========================
 
   So far, I have only used the eql device with the DSLIP SLIP connection
   manager by Matt Dillon (-- "The man who sold his soul to code so much
@@ -100,37 +101,27 @@
   connection.
 
 
-  3.1.	/etc/rc.d/rc.inet1
+3.1. /etc/rc.d/rc.inet1
+-----------------------
 
   In rc.inet1, ifconfig the eql device to the IP address you usually use
   for your machine, and the MTU you prefer for your SLIP lines.	One
   could argue that MTU should be roughly half the usual size for two
   modems, one-third for three, one-fourth for four, etc...  But going
   too far below 296 is probably overkill. Here is an example ifconfig
-  command that sets up the eql device:
+  command that sets up the eql device::
 
-
-
-       ______________________________________________________________________
        ifconfig eql 198.67.33.239 mtu 1006
-       ______________________________________________________________________
-
-
-
-
 
   Once the eql device is up and running, add a static default route to
   it in the routing table using the cool new route syntax that makes
-  life so much easier:
+  life so much easier::
 
-
-
-       ______________________________________________________________________
        route add default eql
-       ______________________________________________________________________
 
 
-  3.2.	Enslaving Devices By Hand
+3.2. Enslaving Devices By Hand
+------------------------------
 
   Enslaving devices by hand requires two utility programs: eql_enslave
   and eql_emancipate (-- eql_emancipate hasn't been written because when
@@ -140,87 +131,56 @@
 
 
   The syntax for enslaving a device is "eql_enslave <master-name>
-  <slave-name> <estimated-bps>".  Here are some example enslavings:
+  <slave-name> <estimated-bps>".  Here are some example enslavings::
 
-
-
-       ______________________________________________________________________
        eql_enslave eql sl0 28800
        eql_enslave eql ppp0 14400
        eql_enslave eql sl1 57600
-       ______________________________________________________________________
-
-
-
-
 
   When you want to free a device from its life of slavery, you can
   either down the device with ifconfig (eql will automatically bury the
   dead slave and remove it from its queue) or use eql_emancipate to free
   it. (-- Or just ifconfig it down, and the eql driver will take it out
-  for you.--)
+  for you.--)::
 
-
-
-       ______________________________________________________________________
        eql_emancipate eql sl0
        eql_emancipate eql ppp0
        eql_emancipate eql sl1
-       ______________________________________________________________________
 
 
-
-
-
-  3.3.	DSLIP Configuration for the eql Device
+3.3. DSLIP Configuration for the eql Device
+-------------------------------------------
 
   The general idea is to bring up and keep up as many SLIP connections
   as you need, automatically.
 
 
-  3.3.1.  /etc/slip/runslip.conf
-
-  Here is an example runslip.conf:
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-  ______________________________________________________________________
-  name		sl-line-1
-  enabled
-  baud		38400
-  mtu		576
-  ducmd		-e /etc/slip/dialout/cua2-288.xp -t 9
-  command	 eql_enslave eql $interface 28800
-  address	 198.67.33.239
-  line		/dev/cua2
-
-  name		sl-line-2
-  enabled
-  baud		38400
-  mtu		576
-  ducmd		-e /etc/slip/dialout/cua3-288.xp -t 9
-  command	 eql_enslave eql $interface 28800
-  address	 198.67.33.239
-  line		/dev/cua3
-  ______________________________________________________________________
-
-
-
-
-
-  3.4.	Using PPP and the eql Device
+3.3.1.  /etc/slip/runslip.conf
+^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^
+
+  Here is an example runslip.conf::
+
+	  name		sl-line-1
+	  enabled
+	  baud		38400
+	  mtu		576
+	  ducmd		-e /etc/slip/dialout/cua2-288.xp -t 9
+	  command	 eql_enslave eql $interface 28800
+	  address	 198.67.33.239
+	  line		/dev/cua2
+
+	  name		sl-line-2
+	  enabled
+	  baud		38400
+	  mtu		576
+	  ducmd		-e /etc/slip/dialout/cua3-288.xp -t 9
+	  command	 eql_enslave eql $interface 28800
+	  address	 198.67.33.239
+	  line		/dev/cua3
+
+
+3.4. Using PPP and the eql Device
+---------------------------------
 
   I have not yet done any load-balancing testing for PPP devices, mainly
   because I don't have a PPP-connection manager like SLIP has with
@@ -235,7 +195,8 @@
   year.
 
 
-  4.  About the Slave Scheduler Algorithm
+4. About the Slave Scheduler Algorithm
+======================================
 
   The slave scheduler probably could be replaced with a dozen other
   things and push traffic much faster.	The formula in the current set
@@ -254,7 +215,8 @@
   traffic and the "slower" modem starved.
 
 
-  5.  Testers' Reports
+5. Testers' Reports
+===================
 
   Some people have experimented with the eql device with newer
   kernels (than 1.1.75).  I have since updated the driver to patch
@@ -262,87 +224,29 @@
   balancing" driver config option.
 
 
-  o  icee from LinuxNET patched 1.1.86 without any rejects and was able
+  -  icee from LinuxNET patched 1.1.86 without any rejects and was able
      to boot the kernel and enslave a couple of ISDN PPP links.
 
-  5.1.	Randolph Bentson's Test Report
+5.1. Randolph Bentson's Test Report
+-----------------------------------
 
+  ::
 
+    From [email protected] Wed Feb  8 19:08:09 1995
+    Date: Tue, 7 Feb 95 22:57 PST
+    From: Randolph Bentson <[email protected]>
+    To: [email protected]
+    Subject: EQL driver tests
 
 
+    I have been checking out your eql driver.  (Nice work, that!)
+    Although you may already done this performance testing, here
+    are some data I've discovered.
 
+    Randolph Bentson
+    [email protected]
 
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-  From [email protected] Wed Feb  8 19:08:09 1995
-  Date: Tue, 7 Feb 95 22:57 PST
-  From: Randolph Bentson <[email protected]>
-  To: [email protected]
-  Subject: EQL driver tests
-
-
-  I have been checking out your eql driver.  (Nice work, that!)
-  Although you may already done this performance testing, here
-  are some data I've discovered.
-
-  Randolph Bentson
-  [email protected]
-
-  ---------------------------------------------------------
+------------------------------------------------------------------
 
 
   A pseudo-device driver, EQL, written by Simon Janes, can be used
@@ -363,7 +267,7 @@
   Once a link was established, I timed a binary ftp transfer of
   289284 bytes of data.	If there were no overhead (packet headers,
   inter-character and inter-packet delays, etc.) the transfers
-  would take the following times:
+  would take the following times::
 
       bits/sec	seconds
       345600	8.3
@@ -388,141 +292,82 @@
   that the connection establishment seemed fragile for the higher
   speeds.  Once established, the connection seemed robust enough.)
 
-  #lines  speed	mtu  seconds	theory  actual  %of
-	 kbit/sec      duration	speed	speed	max
-  3	115200  900	_	345600
-  3	115200  400	18.1	345600  159825  46
-  2	115200  900	_	230400
-  2	115200  600	18.1	230400  159825  69
-  2	115200  400	19.3	230400  149888  65
-  4	57600	900	_	234600
-  4	57600	600	_	234600
-  4	57600	400	_	234600
-  3	57600	600	20.9	172800  138413  80
-  3	57600	900	21.2	172800  136455  78
-  3	115200  600	21.7	345600  133311  38
-  3	57600	400	22.5	172800  128571  74
-  4	38400	900	25.2	153600  114795  74
-  4	38400	600	26.4	153600  109577  71
-  4	38400	400	27.3	153600  105965  68
-  2	57600	900	29.1	115200  99410.3 86
-  1	115200  900	30.7	115200  94229.3 81
-  2	57600	600	30.2	115200  95789.4 83
-  3	38400	900	30.3	115200  95473.3 82
-  3	38400	600	31.2	115200  92719.2 80
-  1	115200  600	31.3	115200  92423	80
-  2	57600	400	32.3	115200  89561.6 77
-  1	115200  400	32.8	115200  88196.3 76
-  3	38400	400	33.5	115200  86353.4 74
-  2	38400	900	43.7	76800	66197.7 86
-  2	38400	600	44	76800	65746.4 85
-  2	38400	400	47.2	76800	61289	79
-  4	19200	900	50.8	76800	56945.7 74
-  4	19200	400	53.2	76800	54376.7 70
-  4	19200	600	53.7	76800	53870.4 70
-  1	57600	900	54.6	57600	52982.4 91
-  1	57600	600	56.2	57600	51474	89
-  3	19200	900	60.5	57600	47815.5 83
-  1	57600	400	60.2	57600	48053.8 83
-  3	19200	600	62	57600	46658.7 81
-  3	19200	400	64.7	57600	44711.6 77
-  1	38400	900	79.4	38400	36433.8 94
-  1	38400	600	82.4	38400	35107.3 91
-  2	19200	900	84.4	38400	34275.4 89
-  1	38400	400	86.8	38400	33327.6 86
-  2	19200	600	87.6	38400	33023.3 85
-  2	19200	400	91.2	38400	31719.7 82
-  4	9600	900	94.7	38400	30547.4 79
-  4	9600	400	106	38400	27290.9 71
-  4	9600	600	110	38400	26298.5 68
-  3	9600	900	118	28800	24515.6 85
-  3	9600	600	120	28800	24107	83
-  3	9600	400	131	28800	22082.7 76
-  1	19200	900	155	19200	18663.5 97
-  1	19200	600	161	19200	17968	93
-  1	19200	400	170	19200	17016.7 88
-  2	9600	600	176	19200	16436.6 85
-  2	9600	900	180	19200	16071.3 83
-  2	9600	400	181	19200	15982.5 83
-  1	9600	900	305	9600	9484.72 98
-  1	9600	600	314	9600	9212.87 95
-  1	9600	400	332	9600	8713.37 90
+  ======  ========	===  ========   ======= ======= ===
+  #lines  speed		mtu  seconds	theory  actual  %of
+	  kbit/sec	     duration	speed	speed	max
+  ======  ========	===  ========   ======= ======= ===
+  3	  115200	900	_	345600
+  3	  115200	400	18.1	345600  159825  46
+  2	  115200	900	_	230400
+  2	  115200	600	18.1	230400  159825  69
+  2	  115200	400	19.3	230400  149888  65
+  4	  57600		900	_	234600
+  4	  57600		600	_	234600
+  4	  57600		400	_	234600
+  3	  57600		600	20.9	172800  138413  80
+  3	  57600		900	21.2	172800  136455  78
+  3	  115200	600	21.7	345600  133311  38
+  3	  57600		400	22.5	172800  128571  74
+  4	  38400		900	25.2	153600  114795  74
+  4	  38400		600	26.4	153600  109577  71
+  4	  38400		400	27.3	153600  105965  68
+  2	  57600		900	29.1	115200  99410.3 86
+  1	  115200	900	30.7	115200  94229.3 81
+  2	  57600		600	30.2	115200  95789.4 83
+  3	  38400		900	30.3	115200  95473.3 82
+  3	  38400		600	31.2	115200  92719.2 80
+  1	  115200	600	31.3	115200  92423	80
+  2	  57600		400	32.3	115200  89561.6 77
+  1	  115200	400	32.8	115200  88196.3 76
+  3	  38400		400	33.5	115200  86353.4 74
+  2	  38400		900	43.7	76800	66197.7 86
+  2	  38400		600	44	76800	65746.4 85
+  2	  38400		400	47.2	76800	61289	79
+  4	  19200		900	50.8	76800	56945.7 74
+  4	  19200		400	53.2	76800	54376.7 70
+  4	  19200		600	53.7	76800	53870.4 70
+  1	  57600		900	54.6	57600	52982.4 91
+  1	  57600		600	56.2	57600	51474	89
+  3	  19200		900	60.5	57600	47815.5 83
+  1	  57600		400	60.2	57600	48053.8 83
+  3	  19200		600	62	57600	46658.7 81
+  3	  19200		400	64.7	57600	44711.6 77
+  1	  38400		900	79.4	38400	36433.8 94
+  1	  38400		600	82.4	38400	35107.3 91
+  2	  19200		900	84.4	38400	34275.4 89
+  1	  38400		400	86.8	38400	33327.6 86
+  2	  19200		600	87.6	38400	33023.3 85
+  2	  19200		400	91.2	38400	31719.7 82
+  4	  9600		900	94.7	38400	30547.4 79
+  4	  9600		400	106	38400	27290.9 71
+  4	  9600		600	110	38400	26298.5 68
+  3	  9600		900	118	28800	24515.6 85
+  3	  9600		600	120	28800	24107	83
+  3	  9600		400	131	28800	22082.7 76
+  1	  19200		900	155	19200	18663.5 97
+  1	  19200		600	161	19200	17968	93
+  1	  19200		400	170	19200	17016.7 88
+  2	  9600		600	176	19200	16436.6 85
+  2	  9600		900	180	19200	16071.3 83
+  2	  9600		400	181	19200	15982.5 83
+  1	  9600		900	305	9600	9484.72 98
+  1	  9600		600	314	9600	9212.87 95
+  1	  9600		400	332	9600	8713.37 90
+  ======  ========	===  ========   ======= ======= ===
 
+5.2. Anthony Healy's Report
+---------------------------
 
+  ::
 
+    Date: Mon, 13 Feb 1995 16:17:29 +1100 (EST)
+    From: Antony Healey <[email protected]>
+    To: Simon Janes <[email protected]>
+    Subject: Re: Load Balancing
 
-
-  5.2.	Anthony Healy's Report
-
-
-
-
-
-
-
-  Date: Mon, 13 Feb 1995 16:17:29 +1100 (EST)
-  From: Antony Healey <[email protected]>
-  To: Simon Janes <[email protected]>
-  Subject: Re: Load Balancing
-
-  Hi Simon,
+    Hi Simon,
 	  I've installed your patch and it works great. I have trialed
 	  it over twin SL/IP lines, just over null modems, but I was
 	  able to data at over 48Kb/s [ISDN link -Simon]. I managed a
 	  transfer of up to 7.5 Kbyte/s on one go, but averaged around
 	  6.4 Kbyte/s, which I think is pretty cool.  :)
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
Documentation/networking/index.rst +1 -0
index 313f66900bce..9ef6ef42bdc5 100644
@@ -54,6 +54,7 @@ Contents:
    defza
    dns_resolver
    driver
+   eql
 
 .. only::  subproject and html
 
drivers/net/Kconfig +1 -1
index 4ab6d343fd86..c822f4a6d166 100644
@@ -126,7 +126,7 @@ config EQUALIZER
 	  Linux driver or with a Livingston Portmaster 2e.
 
 	  Say Y if you want this and read
-	  <file:Documentation/networking/eql.txt>.  You may also want to read
+	  <file:Documentation/networking/eql.rst>.  You may also want to read
 	  section 6.2 of the NET-3-HOWTO, available from
 	  <http://www.tldp.org/docs.html#howto>.
 
Signature · 1 line
2.25.4
#20 lore raw

PATCH 20/38 docs: networking: convert fib_trie.txt to ReST

In reply to Mauro Carvalho Chehab

- add SPDX header;
- adjust title markup;
- adjust identation, whitespaces and blank lines;
- add to networking/index.rst.

---
 .../networking/{fib_trie.txt => fib_trie.rst}    | 16 ++++++++++------
 Documentation/networking/index.rst               |  1 +
 2 files changed, 11 insertions(+), 6 deletions(-)
 rename Documentation/networking/{fib_trie.txt => fib_trie.rst} (96%)
Documentation/networking/fib_trie.rst renamed from Documentation/networking/fib_trie.txt +10 -6
similarity index 96%
rename from Documentation/networking/fib_trie.txt
rename to Documentation/networking/fib_trie.rst
index fe719388518b..f1435b7fcdb7 100644
@@ -1,8 +1,12 @@
-			LC-trie implementation notes.
+.. SPDX-License-Identifier: GPL-2.0
+
+============================
+LC-trie implementation notes
+============================
 
 Node types
 ----------
-leaf 
+leaf
 	An end node with data. This has a copy of the relevant key, along
 	with 'hlist' with routing table entries sorted by prefix length.
 	See struct leaf and struct leaf_info.
@@ -13,7 +17,7 @@ trie node or tnode
 
 A few concepts explained
 ------------------------
-Bits (tnode) 
+Bits (tnode)
 	The number of bits in the key segment used for indexing into the
 	child array - the "child index". See Level Compression.
 
@@ -23,7 +27,7 @@ Pos (tnode)
 
 Path Compression / skipped bits
 	Any given tnode is linked to from the child array of its parent, using
-	a segment of the key specified by the parent's "pos" and "bits" 
+	a segment of the key specified by the parent's "pos" and "bits"
 	In certain cases, this tnode's own "pos" will not be immediately
 	adjacent to the parent (pos+bits), but there will be some bits
 	in the key skipped over because they represent a single path with no
@@ -56,8 +60,8 @@ full_children
 Comments
 ---------
 
-We have tried to keep the structure of the code as close to fib_hash as 
-possible to allow verification and help up reviewing. 
+We have tried to keep the structure of the code as close to fib_hash as
+possible to allow verification and help up reviewing.
 
 fib_find_node()
 	A good start for understanding this code. This function implements a
Documentation/networking/index.rst +1 -0
index 9ef6ef42bdc5..807abe25ae4b 100644
@@ -55,6 +55,7 @@ Contents:
    dns_resolver
    driver
    eql
+   fib_trie
 
 .. only::  subproject and html
 
Signature · 1 line
2.25.4
#21 lore raw

PATCH 21/38 docs: networking: convert filter.txt to ReST

In reply to Mauro Carvalho Chehab

- add SPDX header;
- adjust title markup;
- mark code blocks and literals as such;
- use footnote markup;
- mark tables as such;
- adjust identation, whitespaces and blank lines;
- add to networking/index.rst.

---
 Documentation/bpf/index.rst                   |   4 +-
 .../networking/{filter.txt => filter.rst}     | 850 ++++++++++--------
 Documentation/networking/index.rst            |   1 +
 Documentation/networking/packet_mmap.txt      |   2 +-
 MAINTAINERS                                   |   2 +-
 tools/bpf/bpf_asm.c                           |   2 +-
 tools/bpf/bpf_dbg.c                           |   2 +-
 7 files changed, 485 insertions(+), 378 deletions(-)
 rename Documentation/networking/{filter.txt => filter.rst} (77%)
Documentation/bpf/index.rst +2 -2
index f99677f3572f..38b4db8be7a2 100644
@@ -7,7 +7,7 @@ Filter) facility, with a focus on the extended BPF version (eBPF).
 
 This kernel side documentation is still work in progress.  The main
 textual documentation is (for historical reasons) described in
-`Documentation/networking/filter.txt`_, which describe both classical
+`Documentation/networking/filter.rst`_, which describe both classical
 and extended BPF instruction-set.
 The Cilium project also maintains a `BPF and XDP Reference Guide`_
 that goes into great technical depth about the BPF Architecture.
@@ -59,7 +59,7 @@ Testing and debugging BPF
 
 
 .. Links:
-.. _Documentation/networking/filter.txt: ../networking/filter.txt
+.. _Documentation/networking/filter.rst: ../networking/filter.txt
 .. _man-pages: https://www.kernel.org/doc/man-pages/
 .. _bpf(2): http://man7.org/linux/man-pages/man2/bpf.2.html
 .. _BPF and XDP Reference Guide: http://cilium.readthedocs.io/en/latest/bpf/
Documentation/networking/filter.rst renamed from Documentation/networking/filter.txt +478 -372

1,436 lines not on this page · raw message

Documentation/networking/index.rst +1 -0
index 807abe25ae4b..144ed838c1a9 100644
@@ -56,6 +56,7 @@ Contents:
    driver
    eql
    fib_trie
+   filter
 
 .. only::  subproject and html
 
Documentation/networking/packet_mmap.txt +1 -1
index 999eb41da81d..494614573c67 100644
@@ -1051,7 +1051,7 @@ for more information on hardware timestamps.
 -------------------------------------------------------------------------------
 
 - Packet sockets work well together with Linux socket filters, thus you also
-  might want to have a look at Documentation/networking/filter.txt
+  might want to have a look at Documentation/networking/filter.rst
 
 --------------------------------------------------------------------------------
 + THANKS
MAINTAINERS +1 -1
index f5214418cc19..a14a2d9bb968 100644
@@ -3194,7 +3194,7 @@ Q:	https://patchwork.ozlabs.org/project/netdev/list/?delegate=77147
 T:	git git://git.kernel.org/pub/scm/linux/kernel/git/bpf/bpf.git
 T:	git git://git.kernel.org/pub/scm/linux/kernel/git/bpf/bpf-next.git
 F:	Documentation/bpf/
-F:	Documentation/networking/filter.txt
+F:	Documentation/networking/filter.rst
 F:	arch/*/net/*
 F:	include/linux/bpf*
 F:	include/linux/filter.h
tools/bpf/bpf_asm.c +1 -1
index e5f95e3eede3..0063c3c029e7 100644
@@ -11,7 +11,7 @@
  *
  * How to get into it:
  *
- * 1) read Documentation/networking/filter.txt
+ * 1) read Documentation/networking/filter.rst
  * 2) Run `bpf_asm [-c] <filter-prog file>` to translate into binary
  *    blob that is loadable with xt_bpf, cls_bpf et al. Note: -c will
  *    pretty print a C-like construct.
tools/bpf/bpf_dbg.c +1 -1
index 9d3766e653a9..a0ebcdf59c31 100644
@@ -13,7 +13,7 @@
  * for making a verdict when multiple simple BPF programs are combined
  * into one in order to prevent parsing same headers multiple times.
  *
- * More on how to debug BPF opcodes see Documentation/networking/filter.txt
+ * More on how to debug BPF opcodes see Documentation/networking/filter.rst
  * which is the main document on BPF. Mini howto for getting started:
  *
  *  1) `./bpf_dbg` to enter the shell (shell cmds denoted with '>'):
Signature · 1 line
2.25.4
#22 lore raw

PATCH 22/38 docs: networking: convert fore200e.txt to ReST

In reply to Mauro Carvalho Chehab

- add SPDX header;
- adjust title markup;
- mark code blocks and literals as such;
- adjust identation, whitespaces and blank lines;
- add to networking/index.rst.

---
 Documentation/networking/{fore200e.txt => fore200e.rst} | 8 +++++---
 Documentation/networking/index.rst                      | 1 +
 drivers/atm/Kconfig                                     | 2 +-
 3 files changed, 7 insertions(+), 4 deletions(-)
 rename Documentation/networking/{fore200e.txt => fore200e.rst} (94%)
Documentation/networking/fore200e.rst renamed from Documentation/networking/fore200e.txt +5 -3
similarity index 94%
rename from Documentation/networking/fore200e.txt
rename to Documentation/networking/fore200e.rst
index 1f98f62b4370..55df9ec09ac8 100644
@@ -1,6 +1,8 @@
+.. SPDX-License-Identifier: GPL-2.0
 
+=============================================
 FORE Systems PCA-200E/SBA-200E ATM NIC driver
----------------------------------------------
+=============================================
 
 This driver adds support for the FORE Systems 200E-series ATM adapters
 to the Linux operating system. It is based on the earlier PCA-200E driver
@@ -27,8 +29,8 @@ in the linux/drivers/atm directory for details and restrictions.
 Firmware Updates
 ----------------
 
-The FORE Systems 200E-series driver is shipped with firmware data being 
-uploaded to the ATM adapters at system boot time or at module loading time. 
+The FORE Systems 200E-series driver is shipped with firmware data being
+uploaded to the ATM adapters at system boot time or at module loading time.
 The supplied firmware images should work with all adapters.
 
 However, if you encounter problems (the firmware doesn't start or the driver
Documentation/networking/index.rst +1 -0
index 144ed838c1a9..b2fb8b907d68 100644
@@ -57,6 +57,7 @@ Contents:
    eql
    fib_trie
    filter
+   fore200e
 
 .. only::  subproject and html
 
drivers/atm/Kconfig +1 -1
index 8c37294f1d1e..4af7cbdcc349 100644
@@ -336,7 +336,7 @@ config ATM_FORE200E
 	  on PCI and SBUS hosts. Say Y (or M to compile as a module
 	  named fore_200e) here if you have one of these ATM adapters.
 
-	  See the file <file:Documentation/networking/fore200e.txt> for
+	  See the file <file:Documentation/networking/fore200e.rst> for
 	  further details.
 
 config ATM_FORE200E_USE_TASKLET
Signature · 1 line
2.25.4
#23 lore raw

PATCH 23/38 docs: networking: convert framerelay.txt to ReST

In reply to Mauro Carvalho Chehab

- add SPDX header;
- add a document title;
- adjust identation, whitespaces and blank lines;
- add to networking/index.rst.

---
 .../{framerelay.txt => framerelay.rst}        | 21 ++++++++++++-------
 Documentation/networking/index.rst            |  1 +
 drivers/net/wan/Kconfig                       |  4 ++--
 3 files changed, 16 insertions(+), 10 deletions(-)
 rename Documentation/networking/{framerelay.txt => framerelay.rst} (93%)
Documentation/networking/framerelay.rst renamed from Documentation/networking/framerelay.txt +13 -8
similarity index 93%
rename from Documentation/networking/framerelay.txt
rename to Documentation/networking/framerelay.rst
index 1a0b720440dd..6d904399ec6d 100644
@@ -1,4 +1,10 @@
-Frame Relay (FR) support for linux is built into a two tiered system of device 
+.. SPDX-License-Identifier: GPL-2.0
+
+================
+Frame Relay (FR)
+================
+
+Frame Relay (FR) support for linux is built into a two tiered system of device
 drivers.  The upper layer implements RFC1490 FR specification, and uses the
 Data Link Connection Identifier (DLCI) as its hardware address.  Usually these
 are assigned by your network supplier, they give you the number/numbers of
@@ -7,18 +13,18 @@ the Virtual Connections (VC) assigned to you.
 Each DLCI is a point-to-point link between your machine and a remote one.
 As such, a separate device is needed to accommodate the routing.  Within the
 net-tools archives is 'dlcicfg'.  This program will communicate with the
-base "DLCI" device, and create new net devices named 'dlci00', 'dlci01'... 
+base "DLCI" device, and create new net devices named 'dlci00', 'dlci01'...
 The configuration script will ask you how many DLCIs you need, as well as
 how many DLCIs you want to assign to each Frame Relay Access Device (FRAD).
 
 The DLCI uses a number of function calls to communicate with the FRAD, all
-of which are stored in the FRAD's private data area.  assoc/deassoc, 
+of which are stored in the FRAD's private data area.  assoc/deassoc,
 activate/deactivate and dlci_config.  The DLCI supplies a receive function
 to the FRAD to accept incoming packets.
 
 With this initial offering, only 1 FRAD driver is available.  With many thanks
-to Sangoma Technologies, David Mandelstam & Gene Kozin, the S502A, S502E & 
-S508 are supported.  This driver is currently set up for only FR, but as 
+to Sangoma Technologies, David Mandelstam & Gene Kozin, the S502A, S502E &
+S508 are supported.  This driver is currently set up for only FR, but as
 Sangoma makes more firmware modules available, it can be updated to provide
 them as well.
 
@@ -32,8 +38,7 @@ an initial configuration.
 Additional FRAD device drivers can be added as hardware is available.
 
 At this time, the dlcicfg and fradcfg programs have not been incorporated into
-the net-tools distribution.  They can be found at ftp.invlogic.com, in 
+the net-tools distribution.  They can be found at ftp.invlogic.com, in
 /pub/linux.  Note that with OS/2 FTPD, you end up in /pub by default, so just
-use 'cd linux'.  v0.10 is for use on pre-2.0.3 and earlier, v0.15 is for 
+use 'cd linux'.  v0.10 is for use on pre-2.0.3 and earlier, v0.15 is for
 pre-2.0.4 and later.
-
Documentation/networking/index.rst +1 -0
index b2fb8b907d68..4e225f1f7039 100644
@@ -58,6 +58,7 @@ Contents:
    fib_trie
    filter
    fore200e
+   framerelay
 
 .. only::  subproject and html
 
drivers/net/wan/Kconfig +2 -2
index dbc0e3f7a3e2..3e21726c36e8 100644
@@ -336,7 +336,7 @@ config DLCI
 
 	  To use frame relay, you need supporting hardware (called FRAD) and
 	  certain programs from the net-tools package as explained in
-	  <file:Documentation/networking/framerelay.txt>.
+	  <file:Documentation/networking/framerelay.rst>.
 
 	  To compile this driver as a module, choose M here: the
 	  module will be called dlci.
@@ -361,7 +361,7 @@ config SDLA
 
 	  These are multi-protocol cards, but only Frame Relay is supported
 	  by the driver at this time. Please read
-	  <file:Documentation/networking/framerelay.txt>.
+	  <file:Documentation/networking/framerelay.rst>.
 
 	  To compile this driver as a module, choose M here: the
 	  module will be called sdla.
Signature · 1 line
2.25.4
#24 lore raw

PATCH 24/38 docs: networking: convert generic-hdlc.txt to ReST

In reply to Mauro Carvalho Chehab

- add SPDX header;
- adjust title markup;
- mark code blocks and literals as such;
- adjust identation, whitespaces and blank lines;
- add to networking/index.rst.

---
 .../{generic-hdlc.txt => generic-hdlc.rst}    | 86 +++++++++++++------
 Documentation/networking/index.rst            |  1 +
 2 files changed, 63 insertions(+), 24 deletions(-)
 rename Documentation/networking/{generic-hdlc.txt => generic-hdlc.rst} (75%)
Documentation/networking/generic-hdlc.rst renamed from Documentation/networking/generic-hdlc.txt +62 -24
similarity index 75%
rename from Documentation/networking/generic-hdlc.txt
rename to Documentation/networking/generic-hdlc.rst
index 4eb3cc40b702..1c3bb5cb98d4 100644
@@ -1,14 +1,22 @@
+.. SPDX-License-Identifier: GPL-2.0
+
+==================
 Generic HDLC layer
+==================
+
 Krzysztof Halasa <[email protected]>
 
 
 Generic HDLC layer currently supports:
+
 1. Frame Relay (ANSI, CCITT, Cisco and no LMI)
+
    - Normal (routed) and Ethernet-bridged (Ethernet device emulation)
      interfaces can share a single PVC.
    - ARP support (no InARP support in the kernel - there is an
      experimental InARP user-space daemon available on:
      http://www.kernel.org/pub/linux/utils/net/hdlc/).
+
 2. raw HDLC - either IP (IPv4) interface or Ethernet device emulation
 3. Cisco HDLC
 4. PPP
@@ -24,19 +32,24 @@ with IEEE 802.1Q (VLANs) and 802.1D (Ethernet bridging).
 Make sure the hdlc.o and the hardware driver are loaded. It should
 create a number of "hdlc" (hdlc0 etc) network devices, one for each
 WAN port. You'll need the "sethdlc" utility, get it from:
+
 	http://www.kernel.org/pub/linux/utils/net/hdlc/
 
-Compile sethdlc.c utility:
+Compile sethdlc.c utility::
+
 	gcc -O2 -Wall -o sethdlc sethdlc.c
+
 Make sure you're using a correct version of sethdlc for your kernel.
 
 Use sethdlc to set physical interface, clock rate, HDLC mode used,
 and add any required PVCs if using Frame Relay.
-Usually you want something like:
+Usually you want something like::
 
 	sethdlc hdlc0 clock int rate 128000
 	sethdlc hdlc0 cisco interval 10 timeout 25
-or
+
+or::
+
 	sethdlc hdlc0 rs232 clock ext
 	sethdlc hdlc0 fr lmi ansi
 	sethdlc hdlc0 create 99
@@ -49,46 +62,63 @@ any IP address to it) before using pvc devices.
 
 Setting interface:
 
-* v35 | rs232 | x21 | t1 | e1 - sets physical interface for a given port
-                                if the card has software-selectable interfaces
-  loopback - activate hardware loopback (for testing only)
-* clock ext - both RX clock and TX clock external
-* clock int - both RX clock and TX clock internal
-* clock txint - RX clock external, TX clock internal
-* clock txfromrx - RX clock external, TX clock derived from RX clock
-* rate - sets clock rate in bps (for "int" or "txint" clock only)
+* v35 | rs232 | x21 | t1 | e1
+    - sets physical interface for a given port
+      if the card has software-selectable interfaces
+  loopback
+    - activate hardware loopback (for testing only)
+* clock ext
+    - both RX clock and TX clock external
+* clock int
+    - both RX clock and TX clock internal
+* clock txint
+    - RX clock external, TX clock internal
+* clock txfromrx
+    - RX clock external, TX clock derived from RX clock
+* rate
+    - sets clock rate in bps (for "int" or "txint" clock only)
 
 
 Setting protocol:
 
 * hdlc - sets raw HDLC (IP-only) mode
+
   nrz / nrzi / fm-mark / fm-space / manchester - sets transmission code
+
   no-parity / crc16 / crc16-pr0 (CRC16 with preset zeros) / crc32-itu
+
   crc16-itu (CRC16 with ITU-T polynomial) / crc16-itu-pr0 - sets parity
 
 * hdlc-eth - Ethernet device emulation using HDLC. Parity and encoding
   as above.
 
 * cisco - sets Cisco HDLC mode (IP, IPv6 and IPX supported)
+
   interval - time in seconds between keepalive packets
+
   timeout - time in seconds after last received keepalive packet before
-            we assume the link is down
+	    we assume the link is down
 
 * ppp - sets synchronous PPP mode
 
 * x25 - sets X.25 mode
 
 * fr - Frame Relay mode
+
   lmi ansi / ccitt / cisco / none - LMI (link management) type
+
   dce - Frame Relay DCE (network) side LMI instead of default DTE (user).
+
   It has nothing to do with clocks!
-  t391 - link integrity verification polling timer (in seconds) - user
-  t392 - polling verification timer (in seconds) - network
-  n391 - full status polling counter - user
-  n392 - error threshold - both user and network
-  n393 - monitored events count - both user and network
+
+  - t391 - link integrity verification polling timer (in seconds) - user
+  - t392 - polling verification timer (in seconds) - network
+  - n391 - full status polling counter - user
+  - n392 - error threshold - both user and network
+  - n393 - monitored events count - both user and network
 
 Frame-Relay only:
+
 * create n | delete n - adds / deletes PVC interface with DLCI #n.
   Newly created interface will be named pvc0, pvc1 etc.
 
@@ -101,26 +131,34 @@ Frame-Relay only:
 Board-specific issues
 ---------------------
 
-n2.o and c101.o need parameters to work:
+n2.o and c101.o need parameters to work::
 
 	insmod n2 hw=io,irq,ram,ports[:io,irq,...]
-example:
+
+example::
+
 	insmod n2 hw=0x300,10,0xD0000,01
 
-or
+or::
+
 	insmod c101 hw=irq,ram[:irq,...]
-example:
+
+example::
+
 	insmod c101 hw=9,0xdc000
 
-If built into the kernel, these drivers need kernel (command line) parameters:
+If built into the kernel, these drivers need kernel (command line) parameters::
+
 	n2.hw=io,irq,ram,ports:...
-or
+
+or::
+
 	c101.hw=irq,ram:...
 
 
 
 If you have a problem with N2, C101 or PLX200SYN card, you can issue the
-"private" command to see port's packet descriptor rings (in kernel logs):
+"private" command to see port's packet descriptor rings (in kernel logs)::
 
 	sethdlc hdlc0 private
 
Documentation/networking/index.rst +1 -0
index 4e225f1f7039..d34824b27264 100644
@@ -59,6 +59,7 @@ Contents:
    filter
    fore200e
    framerelay
+   generic-hdlc
 
 .. only::  subproject and html
 
Signature · 1 line
2.25.4
#25 lore raw

PATCH 25/38 docs: networking: convert generic_netlink.txt to ReST

In reply to Mauro Carvalho Chehab

Not much to be done here:
- add SPDX header;
- add a document title;
- add to networking/index.rst.

---
 .../networking/{generic_netlink.txt => generic_netlink.rst} | 6 ++++++
 Documentation/networking/index.rst                          | 1 +
 2 files changed, 7 insertions(+)
 rename Documentation/networking/{generic_netlink.txt => generic_netlink.rst} (64%)
Documentation/networking/generic_netlink.rst renamed from Documentation/networking/generic_netlink.txt +6 -0
similarity index 64%
rename from Documentation/networking/generic_netlink.txt
rename to Documentation/networking/generic_netlink.rst
index 3e071115ca90..59e04ccf80c1 100644
@@ -1,3 +1,9 @@
+.. SPDX-License-Identifier: GPL-2.0
+
+===============
+Generic Netlink
+===============
+
 A wiki document on how to use Generic Netlink can be found here:
 
  * http://www.linuxfoundation.org/collaborate/workgroups/networking/generic_netlink_howto
Documentation/networking/index.rst +1 -0
index d34824b27264..42e556509e22 100644
@@ -60,6 +60,7 @@ Contents:
    fore200e
    framerelay
    generic-hdlc
+   generic_netlink
 
 .. only::  subproject and html
 
Signature · 1 line
2.25.4
#26 lore raw

PATCH 26/38 docs: networking: convert gen_stats.txt to ReST

In reply to Mauro Carvalho Chehab

- add SPDX header;
- mark code blocks and literals as such;
- mark tables as such;
- mark lists as such;
- adjust identation, whitespaces and blank lines;
- add to networking/index.rst.

---
 .../{gen_stats.txt => gen_stats.rst}          | 98 ++++++++++---------
 Documentation/networking/index.rst            |  1 +
 net/core/gen_stats.c                          |  2 +-
 3 files changed, 56 insertions(+), 45 deletions(-)
 rename Documentation/networking/{gen_stats.txt => gen_stats.rst} (60%)
Documentation/networking/gen_stats.rst renamed from Documentation/networking/gen_stats.txt +54 -44
similarity index 60%
rename from Documentation/networking/gen_stats.txt
rename to Documentation/networking/gen_stats.rst
index 179b18ce45ff..595a83b9a61b 100644
@@ -1,67 +1,76 @@
+.. SPDX-License-Identifier: GPL-2.0
+
+===============================================
 Generic networking statistics for netlink users
-======================================================================
+===============================================
 
 Statistic counters are grouped into structs:
 
+==================== ===================== =====================
 Struct               TLV type              Description
-----------------------------------------------------------------------
+==================== ===================== =====================
 gnet_stats_basic     TCA_STATS_BASIC       Basic statistics
 gnet_stats_rate_est  TCA_STATS_RATE_EST    Rate estimator
 gnet_stats_queue     TCA_STATS_QUEUE       Queue statistics
 none                 TCA_STATS_APP         Application specific
+==================== ===================== =====================
 
 
 Collecting:
 -----------
 
-Declare the statistic structs you need:
-struct mystruct {
-	struct gnet_stats_basic	bstats;
-	struct gnet_stats_queue	qstats;
-	...
-};
+Declare the statistic structs you need::
 
-Update statistics, in dequeue() methods only, (while owning qdisc->running)
-mystruct->tstats.packet++;
-mystruct->qstats.backlog += skb->pkt_len;
+	struct mystruct {
+		struct gnet_stats_basic	bstats;
+		struct gnet_stats_queue	qstats;
+		...
+	};
+
+Update statistics, in dequeue() methods only, (while owning qdisc->running)::
+
+	mystruct->tstats.packet++;
+	mystruct->qstats.backlog += skb->pkt_len;
 
 
 Export to userspace (Dump):
 ---------------------------
 
-my_dumping_routine(struct sk_buff *skb, ...)
-{
-	struct gnet_dump dump;
+::
 
-	if (gnet_stats_start_copy(skb, TCA_STATS2, &mystruct->lock, &dump,
-				  TCA_PAD) < 0)
-		goto rtattr_failure;
+    my_dumping_routine(struct sk_buff *skb, ...)
+    {
+	    struct gnet_dump dump;
 
-	if (gnet_stats_copy_basic(&dump, &mystruct->bstats) < 0 ||
-	    gnet_stats_copy_queue(&dump, &mystruct->qstats) < 0 ||
-		gnet_stats_copy_app(&dump, &xstats, sizeof(xstats)) < 0)
-		goto rtattr_failure;
+	    if (gnet_stats_start_copy(skb, TCA_STATS2, &mystruct->lock, &dump,
+				    TCA_PAD) < 0)
+		    goto rtattr_failure;
 
-	if (gnet_stats_finish_copy(&dump) < 0)
-		goto rtattr_failure;
-	...
-}
+	    if (gnet_stats_copy_basic(&dump, &mystruct->bstats) < 0 ||
+		gnet_stats_copy_queue(&dump, &mystruct->qstats) < 0 ||
+		    gnet_stats_copy_app(&dump, &xstats, sizeof(xstats)) < 0)
+		    goto rtattr_failure;
+
+	    if (gnet_stats_finish_copy(&dump) < 0)
+		    goto rtattr_failure;
+	    ...
+    }
 
 TCA_STATS/TCA_XSTATS backward compatibility:
 --------------------------------------------
 
 Prior users of struct tc_stats and xstats can maintain backward
 compatibility by calling the compat wrappers to keep providing the
-existing TLV types.
+existing TLV types::
 
-my_dumping_routine(struct sk_buff *skb, ...)
-{
-    if (gnet_stats_start_copy_compat(skb, TCA_STATS2, TCA_STATS,
-				     TCA_XSTATS, &mystruct->lock, &dump,
-				     TCA_PAD) < 0)
-		goto rtattr_failure;
-	...
-}
+    my_dumping_routine(struct sk_buff *skb, ...)
+    {
+	if (gnet_stats_start_copy_compat(skb, TCA_STATS2, TCA_STATS,
+					TCA_XSTATS, &mystruct->lock, &dump,
+					TCA_PAD) < 0)
+		    goto rtattr_failure;
+	    ...
+    }
 
 A struct tc_stats will be filled out during gnet_stats_copy_* calls
 and appended to the skb. TCA_XSTATS is provided if gnet_stats_copy_app
@@ -77,7 +86,7 @@ are responsible for making sure that the lock is initialized.
 
 
 Rate Estimator:
---------------
+---------------
 
 0) Prepare an estimator attribute. Most likely this would be in user
    space. The value of this TLV should contain a tc_estimator structure.
@@ -92,18 +101,19 @@ Rate Estimator:
    TCA_RATE to your code in the kernel.
 
 In the kernel when setting up:
+
 1) make sure you have basic stats and rate stats setup first.
 2) make sure you have initialized stats lock that is used to setup such
    stats.
-3) Now initialize a new estimator:
+3) Now initialize a new estimator::
 
-   int ret = gen_new_estimator(my_basicstats,my_rate_est_stats,
-       mystats_lock, attr_with_tcestimator_struct);
+    int ret = gen_new_estimator(my_basicstats,my_rate_est_stats,
+	mystats_lock, attr_with_tcestimator_struct);
 
-   if ret == 0
-       success
-   else
-       failed
+    if ret == 0
+	success
+    else
+	failed
 
 From now on, every time you dump my_rate_est_stats it will contain
 up-to-date info.
@@ -115,5 +125,5 @@ are still valid (i.e still exist) at the time of making this call.
 
 Authors:
 --------
-Thomas Graf <[email protected]>
-Jamal Hadi Salim <[email protected]>
+- Thomas Graf <[email protected]>
+- Jamal Hadi Salim <[email protected]>
Documentation/networking/index.rst +1 -0
index 42e556509e22..33afbb67f3fa 100644
@@ -61,6 +61,7 @@ Contents:
    framerelay
    generic-hdlc
    generic_netlink
+   gen_stats
 
 .. only::  subproject and html
 
net/core/gen_stats.c +1 -1
index 1d653fbfcf52..e491b083b348 100644
@@ -6,7 +6,7 @@
  *           Jamal Hadi Salim
  *           Alexey Kuznetsov, <[email protected]>
  *
- * See Documentation/networking/gen_stats.txt
+ * See Documentation/networking/gen_stats.rst
  */
 
 #include <linux/types.h>
Signature · 1 line
2.25.4
#27 lore raw

PATCH 27/38 docs: networking: convert gtp.txt to ReST

In reply to Mauro Carvalho Chehab

- add SPDX header;
- adjust titles and chapters, adding proper markups;
- add notes markups;
- adjust identation, whitespaces and blank lines;
- add to networking/index.rst.

---
 Documentation/networking/{gtp.txt => gtp.rst} | 95 +++++++++++--------
 Documentation/networking/index.rst            |  1 +
 2 files changed, 59 insertions(+), 37 deletions(-)
 rename Documentation/networking/{gtp.txt => gtp.rst} (79%)
Documentation/networking/gtp.rst renamed from Documentation/networking/gtp.txt +58 -37
similarity index 79%
rename from Documentation/networking/gtp.txt
rename to Documentation/networking/gtp.rst
index 6966bbec1ecb..1563fb94b289 100644
@@ -1,12 +1,18 @@
+.. SPDX-License-Identifier: GPL-2.0
+
+=====================================
 The Linux kernel GTP tunneling module
-======================================================================
-Documentation by Harald Welte <[email protected]> and
-                 Andreas Schultz <[email protected]>
+=====================================
+
+Documentation by
+		 Harald Welte <[email protected]> and
+		 Andreas Schultz <[email protected]>
 
 In 'drivers/net/gtp.c' you are finding a kernel-level implementation
 of a GTP tunnel endpoint.
 
-== What is GTP ==
+What is GTP
+===========
 
 GTP is the Generic Tunnel Protocol, which is a 3GPP protocol used for
 tunneling User-IP payload between a mobile station (phone, modem)
@@ -41,7 +47,8 @@ publicly via the 3GPP website at http://www.3gpp.org/DynaReport/29060.htm
 A direct PDF link to v13.6.0 is provided for convenience below:
 http://www.etsi.org/deliver/etsi_ts/129000_129099/129060/13.06.00_60/ts_129060v130600p.pdf
 
-== The Linux GTP tunnelling module ==
+The Linux GTP tunnelling module
+===============================
 
 The module implements the function of a tunnel endpoint, i.e. it is
 able to decapsulate tunneled IP packets in the uplink originated by
@@ -70,7 +77,8 @@ Userspace :)
 The official homepage of the module is at
 https://osmocom.org/projects/linux-kernel-gtp-u/wiki
 
-== Userspace Programs with Linux Kernel GTP-U support ==
+Userspace Programs with Linux Kernel GTP-U support
+==================================================
 
 At the time of this writing, there are at least two Free Software
 implementations that implement GTP-C and can use the netlink interface
@@ -82,7 +90,8 @@ to make use of the Linux kernel GTP-U support:
 * ergw (GGSN + P-GW in Erlang):
   https://github.com/travelping/ergw
 
-== Userspace Library / Command Line Utilities ==
+Userspace Library / Command Line Utilities
+==========================================
 
 There is a userspace library called 'libgtpnl' which is based on
 libmnl and which implements a C-language API towards the netlink
@@ -90,7 +99,8 @@ interface provided by the Kernel GTP module:
 
 http://git.osmocom.org/libgtpnl/
 
-== Protocol Versions ==
+Protocol Versions
+=================
 
 There are two different versions of GTP-U: v0 [GSM TS 09.60] and v1
 [3GPP TS 29.281].  Both are implemented in the Kernel GTP module.
@@ -105,7 +115,8 @@ doesn't implement GTP-C, we don't have to worry about this.  It's the
 responsibility of the control plane implementation in userspace to
 implement that.
 
-== IPv6 ==
+IPv6
+====
 
 The 3GPP specifications indicate either IPv4 or IPv6 can be used both
 on the inner (user) IP layer, or on the outer (transport) layer.
@@ -114,22 +125,25 @@ Unfortunately, the Kernel module currently supports IPv6 neither for
 the User IP payload, nor for the outer IP layer.  Patches or other
 Contributions to fix this are most welcome!
 
-== Mailing List ==
+Mailing List
+============
 
-If yo have questions regarding how to use the Kernel GTP module from
+If you have questions regarding how to use the Kernel GTP module from
 your own software, or want to contribute to the code, please use the
 osmocom-net-grps mailing list for related discussion. The list can be
 reached at [email protected] and the mailman
 interface for managing your subscription is at
 https://lists.osmocom.org/mailman/listinfo/osmocom-net-gprs
 
-== Issue Tracker ==
+Issue Tracker
+=============
 
 The Osmocom project maintains an issue tracker for the Kernel GTP-U
 module at
 https://osmocom.org/projects/linux-kernel-gtp-u/issues
 
-== History / Acknowledgements ==
+History / Acknowledgements
+==========================
 
 The Module was originally created in 2012 by Harald Welte, but never
 completed.  Pablo came in to finish the mess Harald left behind.  But
@@ -139,9 +153,11 @@ In 2015, Andreas Schultz came to the rescue and fixed lots more bugs,
 extended it with new features and finally pushed all of us to get it
 mainline, where it was merged in 4.7.0.
 
-== Architectural Details ==
+Architectural Details
+=====================
 
-=== Local GTP-U entity and tunnel identification ===
+Local GTP-U entity and tunnel identification
+--------------------------------------------
 
 GTP-U uses UDP for transporting PDU's. The receiving UDP port is 2152
 for GTPv1-U and 3386 for GTPv0-U.
@@ -164,15 +180,15 @@ Therefore:
     destination IP and the tunnel endpoint id. The source IP and port
     have no meaning and can change at any time.
 
-[3GPP TS 29.281] Section 4.3.0 defines this so:
+[3GPP TS 29.281] Section 4.3.0 defines this so::
 
-> The TEID in the GTP-U header is used to de-multiplex traffic
-> incoming from remote tunnel endpoints so that it is delivered to the
-> User plane entities in a way that allows multiplexing of different
-> users, different packet protocols and different QoS levels.
-> Therefore no two remote GTP-U endpoints shall send traffic to a
-> GTP-U protocol entity using the same TEID value except
-> for data forwarding as part of mobility procedures.
+  The TEID in the GTP-U header is used to de-multiplex traffic
+  incoming from remote tunnel endpoints so that it is delivered to the
+  User plane entities in a way that allows multiplexing of different
+  users, different packet protocols and different QoS levels.
+  Therefore no two remote GTP-U endpoints shall send traffic to a
+  GTP-U protocol entity using the same TEID value except
+  for data forwarding as part of mobility procedures.
 
 The definition above only defines that two remote GTP-U endpoints
 *should not* send to the same TEID, it *does not* forbid or exclude
@@ -183,7 +199,8 @@ multiple or unknown peers.
 Therefore, the receiving side identifies tunnels exclusively based on
 TEIDs, not based on the source IP!
 
-== APN vs. Network Device ==
+APN vs. Network Device
+======================
 
 The GTP-U driver creates a Linux network device for each Gi/SGi
 interface.
@@ -201,29 +218,33 @@ number of Gi/SGi interfaces implemented by a GGSN/P-GW.
 
 [3GPP TS 29.061] Section 11.3 makes it clear that the selection of a
 specific Gi/SGi interfaces is made through the Access Point Name
-(APN):
+(APN)::
 
-> 2. each private network manages its own addressing. In general this
->    will result in different private networks having overlapping
->    address ranges. A logically separate connection (e.g. an IP in IP
->    tunnel or layer 2 virtual circuit) is used between the GGSN/P-GW
->    and each private network.
->
->    In this case the IP address alone is not necessarily unique.  The
->    pair of values, Access Point Name (APN) and IPv4 address and/or
->    IPv6 prefixes, is unique.
+  2. each private network manages its own addressing. In general this
+     will result in different private networks having overlapping
+     address ranges. A logically separate connection (e.g. an IP in IP
+     tunnel or layer 2 virtual circuit) is used between the GGSN/P-GW
+     and each private network.
+
+     In this case the IP address alone is not necessarily unique.  The
+     pair of values, Access Point Name (APN) and IPv4 address and/or
+     IPv6 prefixes, is unique.
 
 In order to support the overlapping address range use case, each APN
 is mapped to a separate Gi/SGi interface (network device).
 
-NOTE: The Access Point Name is purely a control plane (GTP-C) concept.
-At the GTP-U level, only Tunnel Endpoint Identifiers are present in
-GTP-U packets and network devices are known
+.. note::
+
+   The Access Point Name is purely a control plane (GTP-C) concept.
+   At the GTP-U level, only Tunnel Endpoint Identifiers are present in
+   GTP-U packets and network devices are known
 
 Therefore for a given UE the mapping in IP to PDN network is:
+
   * network device + MS IP -> Peer IP + Peer TEID,
 
 and from PDN to IP network:
+
   * local GTP-U IP + TEID  -> network device
 
 Furthermore, before a received T-PDU is injected into the network
Documentation/networking/index.rst +1 -0
index 33afbb67f3fa..b29a08d1f941 100644
@@ -62,6 +62,7 @@ Contents:
    generic-hdlc
    generic_netlink
    gen_stats
+   gtp
 
 .. only::  subproject and html
 
Signature · 1 line
2.25.4
#28 lore raw

PATCH 28/38 docs: networking: convert hinic.txt to ReST

In reply to Mauro Carvalho Chehab

Not much to be done here:

- add SPDX header;
- adjust titles and chapters, adding proper markups;
- adjust identation, whitespaces and blank lines;
- add to networking/index.rst.

---
 Documentation/networking/{hinic.txt => hinic.rst} | 5 ++++-
 Documentation/networking/index.rst                | 1 +
 MAINTAINERS                                       | 2 +-
 3 files changed, 6 insertions(+), 2 deletions(-)
 rename Documentation/networking/{hinic.txt => hinic.rst} (97%)
Documentation/networking/hinic.rst renamed from Documentation/networking/hinic.txt +4 -1
similarity index 97%
rename from Documentation/networking/hinic.txt
rename to Documentation/networking/hinic.rst
index 989366a4039c..867ac8f4e04a 100644
@@ -1,3 +1,6 @@
+.. SPDX-License-Identifier: GPL-2.0
+
+============================================================
 Linux Kernel Driver for Huawei Intelligent NIC(HiNIC) family
 ============================================================
 
@@ -110,7 +113,7 @@ hinic_dev - de/constructs the Logical Tx and Rx Queues.
 (hinic_main.c, hinic_dev.h)
 
 
-Miscellaneous:
+Miscellaneous
 =============
 
 Common functions that are used by HW and Logical Device.
Documentation/networking/index.rst +1 -0
index b29a08d1f941..5a7889df1375 100644
@@ -63,6 +63,7 @@ Contents:
    generic_netlink
    gen_stats
    gtp
+   hinic
 
 .. only::  subproject and html
 
MAINTAINERS +1 -1
index a14a2d9bb968..3764697a6002 100644
@@ -7837,7 +7837,7 @@ HUAWEI ETHERNET DRIVER
 M:	Aviad Krawczyk <[email protected]>
 L:	[email protected]
 S:	Supported
-F:	Documentation/networking/hinic.txt
+F:	Documentation/networking/hinic.rst
 F:	drivers/net/ethernet/huawei/hinic/
 
 HUGETLB FILESYSTEM
Signature · 1 line
2.25.4
#29 lore raw

PATCH 29/38 docs: networking: convert ila.txt to ReST

In reply to Mauro Carvalho Chehab

- add SPDX header;
- adjust title markup;
- mark code blocks and literals as such;
- adjust identation, whitespaces and blank lines;
- add to networking/index.rst.

---
 Documentation/networking/{ila.txt => ila.rst} | 81 +++++++++++--------
 Documentation/networking/index.rst            |  1 +
 2 files changed, 47 insertions(+), 35 deletions(-)
 rename Documentation/networking/{ila.txt => ila.rst} (82%)
Documentation/networking/ila.rst renamed from Documentation/networking/ila.txt +46 -35
similarity index 82%
rename from Documentation/networking/ila.txt
rename to Documentation/networking/ila.rst
index a17dac9dc915..5ac0a6270b17 100644
@@ -1,4 +1,8 @@
+.. SPDX-License-Identifier: GPL-2.0
+
+===================================
 Identifier Locator Addressing (ILA)
+===================================
 
 
 Introduction
@@ -26,11 +30,13 @@ The ILA protocol is described in Internet-Draft draft-herbert-intarea-ila.
 ILA terminology
 ===============
 
-  - Identifier	A number that identifies an addressable node in the network
+  - Identifier
+		A number that identifies an addressable node in the network
 		independent of its location. ILA identifiers are sixty-four
 		bit values.
 
-  - Locator	A network prefix that routes to a physical host. Locators
+  - Locator
+		A network prefix that routes to a physical host. Locators
 		provide the topological location of an addressed node. ILA
 		locators are sixty-four bit prefixes.
 
@@ -51,17 +57,20 @@ ILA terminology
 		bits) and an identifier (low order sixty-four bits). ILA
 		addresses are never visible to an application.
 
-  - ILA host	An end host that is capable of performing ILA translations
+  - ILA host
+		An end host that is capable of performing ILA translations
 		on transmit or receive.
 
-  - ILA router	A network node that performs ILA translation and forwarding
+  - ILA router
+		A network node that performs ILA translation and forwarding
 		of translated packets.
 
   - ILA forwarding cache
 		A type of ILA router that only maintains a working set
 		cache of mappings.
 
-  - ILA node	A network node capable of performing ILA translations. This
+  - ILA node
+		A network node capable of performing ILA translations. This
 		can be an ILA router, ILA forwarding cache, or ILA host.
 
 
@@ -82,18 +91,18 @@ Configuration and datapath for these two points of deployment is somewhat
 different.
 
 The diagram below illustrates the flow of packets through ILA as well
-as showing ILA hosts and routers.
+as showing ILA hosts and routers::
 
     +--------+                                                +--------+
     | Host A +-+                                         +--->| Host B |
     |        | |              (2) ILA                   (')   |        |
     +--------+ |            ...addressed....           (   )  +--------+
-               V  +---+--+  .  packet      .  +---+--+  (_)
+	       V  +---+--+  .  packet      .  +---+--+  (_)
    (1) SIR     |  | ILA  |----->-------->---->| ILA  |   |   (3) SIR
     addressed  +->|router|  .              .  |router|->-+    addressed
     packet        +---+--+  .     IPv6     .  +---+--+        packet
-                   /        .    Network   .
-                  /         .              .   +--+-++--------+
+		   /        .    Network   .
+		  /         .              .   +--+-++--------+
     +--------+   /          .              .   |ILA ||  Host  |
     |  Host  +--+           .              .- -|host||        |
     |        |              .              .   +--+-++--------+
@@ -173,7 +182,7 @@ ILA address, never a SIR address.
 
 In the simplest format the identifier types, C-bit, and checksum
 adjustment value are not present so an identifier is considered an
-unstructured sixty-four bit value.
+unstructured sixty-four bit value::
 
      +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
      |                            Identifier                         |
@@ -184,7 +193,7 @@ unstructured sixty-four bit value.
 The checksum neutral adjustment may be configured to always be
 present using neutral-map-auto. In this case there is no C-bit, but the
 checksum adjustment is in the low order 16 bits. The identifier is
-still sixty-four bits.
+still sixty-four bits::
 
      +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
      |                            Identifier                         |
@@ -193,7 +202,7 @@ still sixty-four bits.
      +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
 
 The C-bit may used to explicitly indicate that checksum neutral
-mapping has been applied to an ILA address. The format is:
+mapping has been applied to an ILA address. The format is::
 
      +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
      |     |C|                    Identifier                         |
@@ -204,7 +213,7 @@ mapping has been applied to an ILA address. The format is:
 The identifier type field may be present to indicate the identifier
 type. If it is not present then the type is inferred based on mapping
 configuration. The checksum neutral adjustment may automatically
-used with the identifier type as illustrated below.
+used with the identifier type as illustrated below::
 
      +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
      | Type|                      Identifier                         |
@@ -213,7 +222,7 @@ used with the identifier type as illustrated below.
      +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
 
 If the identifier type and the C-bit can be present simultaneously so
-the identifier format would be:
+the identifier format would be::
 
      +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
      | Type|C|                    Identifier                         |
@@ -258,28 +267,30 @@ same meanings as described above.
 Some examples
 =============
 
-# Configure an ILA route that uses checksum neutral mapping as well
-# as type field. Note that the type field is set in the SIR address
-# (the 2000 implies type is 1 which is LUID).
-ip route add 3333:0:0:1:2000:0:1:87/128 encap ila 2001:0:87:0 \
-     csum-mode neutral-map ident-type use-format
+::
 
-# Configure an ILA LWT route that uses auto checksum neutral mapping
-# (no C-bit) and configure identifier type to be LUID so that the
-# identifier type field will not be present.
-ip route add 3333:0:0:1:2000:0:2:87/128 encap ila 2001:0:87:1 \
-     csum-mode neutral-map-auto ident-type luid
+     # Configure an ILA route that uses checksum neutral mapping as well
+     # as type field. Note that the type field is set in the SIR address
+     # (the 2000 implies type is 1 which is LUID).
+     ip route add 3333:0:0:1:2000:0:1:87/128 encap ila 2001:0:87:0 \
+	  csum-mode neutral-map ident-type use-format
 
-ila_xlat configuration
+     # Configure an ILA LWT route that uses auto checksum neutral mapping
+     # (no C-bit) and configure identifier type to be LUID so that the
+     # identifier type field will not be present.
+     ip route add 3333:0:0:1:2000:0:2:87/128 encap ila 2001:0:87:1 \
+	  csum-mode neutral-map-auto ident-type luid
 
-# Configure an ILA to SIR mapping that matches a locator and overwrites
-# it with a SIR address (3333:0:0:1 in this example). The C-bit and
-# identifier field are used.
-ip ila add loc_match 2001:0:119:0 loc 3333:0:0:1 \
-    csum-mode neutral-map-auto ident-type use-format
+     ila_xlat configuration
 
-# Configure an ILA to SIR mapping where checksum neutral is automatically
-# set without the C-bit and the identifier type is configured to be LUID
-# so that the identifier type field is not present.
-ip ila add loc_match 2001:0:119:0 loc 3333:0:0:1 \
-    csum-mode neutral-map-auto ident-type use-format
+     # Configure an ILA to SIR mapping that matches a locator and overwrites
+     # it with a SIR address (3333:0:0:1 in this example). The C-bit and
+     # identifier field are used.
+     ip ila add loc_match 2001:0:119:0 loc 3333:0:0:1 \
+	 csum-mode neutral-map-auto ident-type use-format
+
+     # Configure an ILA to SIR mapping where checksum neutral is automatically
+     # set without the C-bit and the identifier type is configured to be LUID
+     # so that the identifier type field is not present.
+     ip ila add loc_match 2001:0:119:0 loc 3333:0:0:1 \
+	 csum-mode neutral-map-auto ident-type use-format
Documentation/networking/index.rst +1 -0
index 5a7889df1375..488971f6b650 100644
@@ -64,6 +64,7 @@ Contents:
    gen_stats
    gtp
    hinic
+   ila
 
 .. only::  subproject and html
 
Signature · 1 line
2.25.4
#30 lore raw

PATCH 30/38 docs: networking: convert ipddp.txt to ReST

In reply to Mauro Carvalho Chehab

Not much to be done here:

- add SPDX header;
- use a document title from existing text;
- adjust a chapter markup;
- add to networking/index.rst.

---
 Documentation/networking/index.rst                |  1 +
 Documentation/networking/{ipddp.txt => ipddp.rst} | 13 +++++++++----
 Documentation/networking/ltpc.txt                 |  2 +-
 drivers/net/appletalk/Kconfig                     |  4 ++--
 4 files changed, 13 insertions(+), 7 deletions(-)
 rename Documentation/networking/{ipddp.txt => ipddp.rst} (89%)
Documentation/networking/index.rst +1 -0
index 488971f6b650..cf85d0a73144 100644
@@ -65,6 +65,7 @@ Contents:
    gtp
    hinic
    ila
+   ipddp
 
 .. only::  subproject and html
 
Documentation/networking/ipddp.rst renamed from Documentation/networking/ipddp.txt +9 -4
similarity index 89%
rename from Documentation/networking/ipddp.txt
rename to Documentation/networking/ipddp.rst
index ba5c217fffe0..be7091b77927 100644
@@ -1,7 +1,12 @@
-Text file for ipddp.c:
-	AppleTalk-IP Decapsulation and AppleTalk-IP Encapsulation
+.. SPDX-License-Identifier: GPL-2.0
 
-This text file is written by Jay Schulist <[email protected]>
+=========================================================
+AppleTalk-IP Decapsulation and AppleTalk-IP Encapsulation
+=========================================================
+
+Documentation ipddp.c
+
+This file is written by Jay Schulist <[email protected]>
 
 Introduction
 ------------
@@ -21,7 +26,7 @@ kernel AppleTalk layer and drivers are available.
 Each mode requires its own user space software.
 
 Compiling AppleTalk-IP Decapsulation/Encapsulation
-=================================================
+==================================================
 
 AppleTalk-IP decapsulation needs to be compiled into your kernel. You
 will need to turn on AppleTalk-IP driver support. Then you will need to
Documentation/networking/ltpc.txt +1 -1
index 0bf3220c715b..a005a73b76d0 100644
@@ -99,7 +99,7 @@ treat the LocalTalk device like an ordinary Ethernet device, even if
 that's what it looks like to Netatalk.
 
 Instead, you follow the same procedure as for doing IP in EtherTalk.
-See Documentation/networking/ipddp.txt for more information about the
+See Documentation/networking/ipddp.rst for more information about the
 kernel driver and userspace tools needed.
 
 --------------------------------------
drivers/net/appletalk/Kconfig +2 -2
index d4e51c048f62..ccde6479050c 100644
@@ -86,7 +86,7 @@ config IPDDP
 	  box is stuck on an AppleTalk only network) or decapsulate (e.g. if
 	  you want your Linux box to act as an Internet gateway for a zoo of
 	  AppleTalk connected Macs). Please see the file
-	  <file:Documentation/networking/ipddp.txt> for more information.
+	  <file:Documentation/networking/ipddp.rst> for more information.
 
 	  If you say Y here, the AppleTalk-IP support will be compiled into
 	  the kernel. In this case, you can either use encapsulation or
@@ -107,4 +107,4 @@ config IPDDP_ENCAP
 	  IP packets inside AppleTalk frames; this is useful if your Linux box
 	  is stuck on an AppleTalk network (which hopefully contains a
 	  decapsulator somewhere). Please see
-	  <file:Documentation/networking/ipddp.txt> for more information.
+	  <file:Documentation/networking/ipddp.rst> for more information.
Signature · 1 line
2.25.4
#31 lore raw

PATCH 31/38 docs: networking: convert ip_dynaddr.txt to ReST

In reply to Mauro Carvalho Chehab

- add SPDX header;
- adjust title markup;
- mark code blocks and literals as such;
- adjust identation, whitespaces and blank lines;
- add to networking/index.rst.

---
 Documentation/networking/index.rst            |  1 +
 .../{ip_dynaddr.txt => ip_dynaddr.rst}        | 29 +++++++++++++------
 2 files changed, 21 insertions(+), 9 deletions(-)
 rename Documentation/networking/{ip_dynaddr.txt => ip_dynaddr.rst} (65%)
Documentation/networking/index.rst +1 -0
index cf85d0a73144..f81aeb87aa28 100644
@@ -66,6 +66,7 @@ Contents:
    hinic
    ila
    ipddp
+   ip_dynaddr
 
 .. only::  subproject and html
 
Documentation/networking/ip_dynaddr.rst renamed from Documentation/networking/ip_dynaddr.txt +20 -9
similarity index 65%
rename from Documentation/networking/ip_dynaddr.txt
rename to Documentation/networking/ip_dynaddr.rst
index 45f3c1268e86..eacc0c780c7f 100644
@@ -1,10 +1,15 @@
+.. SPDX-License-Identifier: GPL-2.0
+
+==================================
 IP dynamic address hack-port v0.03
-~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
+==================================
+
 This stuff allows diald ONESHOT connections to get established by
 dynamically changing packet source address (and socket's if local procs).
 It is implemented for TCP diald-box connections(1) and IP_MASQuerading(2).
 
-If enabled[*] and forwarding interface has changed:
+If enabled\ [#]_ and forwarding interface has changed:
+
   1)  Socket (and packet) source address is rewritten ON RETRANSMISSIONS
       while in SYN_SENT state (diald-box processes).
   2)  Out-bounded MASQueraded source address changes ON OUTPUT (when
@@ -12,18 +17,24 @@ If enabled[*] and forwarding interface has changed:
       received by the tunnel.
 
 This is specially helpful for auto dialup links (diald), where the
-``actual'' outgoing address is unknown at the moment the link is
+``actual`` outgoing address is unknown at the moment the link is
 going up. So, the *same* (local AND masqueraded) connections requests that
 bring the link up will be able to get established.
 
-[*] At boot, by default no address rewriting is attempted. 
-  To enable:
+.. [#] At boot, by default no address rewriting is attempted.
+
+  To enable::
+
      # echo 1 > /proc/sys/net/ipv4/ip_dynaddr
-  To enable verbose mode:
-     # echo 2 > /proc/sys/net/ipv4/ip_dynaddr
-  To disable (default)
+
+  To enable verbose mode::
+
+    # echo 2 > /proc/sys/net/ipv4/ip_dynaddr
+
+  To disable (default)::
+
      # echo 0 > /proc/sys/net/ipv4/ip_dynaddr
 
 Enjoy!
 
--- Juanjo  <[email protected]>
+Juanjo  <[email protected]>
Signature · 1 line
2.25.4
#32 lore raw

PATCH 32/38 docs: networking: convert iphase.txt to ReST

In reply to Mauro Carvalho Chehab

- add SPDX header;
- adjust title using the proper markup;
- mark code blocks and literals as such;
- mark tables as such;
- mark lists as such;
- adjust identation, whitespaces and blank lines;
- add to networking/index.rst.

---
 Documentation/networking/index.rst            |   1 +
 .../networking/{iphase.txt => iphase.rst}     | 185 +++++++++++-------
 drivers/atm/Kconfig                           |   2 +-
 3 files changed, 112 insertions(+), 76 deletions(-)
 rename Documentation/networking/{iphase.txt => iphase.rst} (50%)
Documentation/networking/index.rst +1 -0
index f81aeb87aa28..505eaa41ca2b 100644
@@ -67,6 +67,7 @@ Contents:
    ila
    ipddp
    ip_dynaddr
+   iphase
 
 .. only::  subproject and html
 
Documentation/networking/iphase.rst renamed from Documentation/networking/iphase.txt +110 -75

265 lines not on this page · raw message

drivers/atm/Kconfig +1 -1
index 4af7cbdcc349..cfb0d16b60ad 100644
@@ -306,7 +306,7 @@ config ATM_IA
 	  for more info about the cards. Say Y (or M to compile as a module
 	  named iphase) here if you have one of these cards.
 
-	  See the file <file:Documentation/networking/iphase.txt> for further
+	  See the file <file:Documentation/networking/iphase.rst> for further
 	  details.
 
 config ATM_IA_DEBUG
Signature · 1 line
2.25.4
#33 lore raw

PATCH 33/38 docs: networking: convert ipsec.txt to ReST

In reply to Mauro Carvalho Chehab

Not much to be done here:

- add SPDX header;
- add a document title;
- adjust identation, whitespaces and blank lines;
- add to networking/index.rst.

---
 Documentation/networking/index.rst                |  1 +
 Documentation/networking/{ipsec.txt => ipsec.rst} | 14 +++++++++++---
 2 files changed, 12 insertions(+), 3 deletions(-)
 rename Documentation/networking/{ipsec.txt => ipsec.rst} (90%)
Documentation/networking/index.rst +1 -0
index 505eaa41ca2b..3efb4608649a 100644
@@ -68,6 +68,7 @@ Contents:
    ipddp
    ip_dynaddr
    iphase
+   ipsec
 
 .. only::  subproject and html
 
Documentation/networking/ipsec.rst renamed from Documentation/networking/ipsec.txt +11 -3
similarity index 90%
rename from Documentation/networking/ipsec.txt
rename to Documentation/networking/ipsec.rst
index ba794b7e51be..afe9d7b48be3 100644
@@ -1,12 +1,20 @@
+.. SPDX-License-Identifier: GPL-2.0
+
+=====
+IPsec
+=====
+
 
 Here documents known IPsec corner cases which need to be keep in mind when
 deploy various IPsec configuration in real world production environment.
 
-1. IPcomp: Small IP packet won't get compressed at sender, and failed on
+1. IPcomp:
+	   Small IP packet won't get compressed at sender, and failed on
 	   policy check on receiver.
 
-Quote from RFC3173:
-2.2. Non-Expansion Policy
+Quote from RFC3173::
+
+  2.2. Non-Expansion Policy
 
    If the total size of a compressed payload and the IPComp header, as
    defined in section 3, is not smaller than the size of the original
Signature · 1 line
2.25.4
#34 lore raw

PATCH 34/38 docs: networking: convert ip-sysctl.txt to ReST

In reply to Mauro Carvalho Chehab

- add SPDX header;
- adjust titles and chapters, adding proper markups;
- mark code blocks and literals as such;
- mark lists as such;
- mark tables as such;
- use footnote markup;
- adjust identation, whitespaces and blank lines;
- add to networking/index.rst.

---
 .../admin-guide/kernel-parameters.txt         |   2 +-
 Documentation/admin-guide/sysctl/net.rst      |   2 +-
 Documentation/networking/index.rst            |   1 +
 .../{ip-sysctl.txt => ip-sysctl.rst}          | 829 ++++++++++++------
 Documentation/networking/snmp_counter.rst     |   2 +-
 net/Kconfig                                   |   2 +-
 net/ipv4/Kconfig                              |   2 +-
 net/ipv4/icmp.c                               |   2 +-
 8 files changed, 559 insertions(+), 283 deletions(-)
 rename Documentation/networking/{ip-sysctl.txt => ip-sysctl.rst} (83%)
Documentation/admin-guide/kernel-parameters.txt +1 -1
index cd68635370c6..ef9779398cee 100644
@@ -4950,7 +4950,7 @@
 			Set the number of tcp_metrics_hash slots.
 			Default value is 8192 or 16384 depending on total
 			ram pages. This is used to specify the TCP metrics
-			cache size. See Documentation/networking/ip-sysctl.txt
+			cache size. See Documentation/networking/ip-sysctl.rst
 			"tcp_no_metrics_save" section for more details.
 
 	tdfx=		[HW,DRM]
Documentation/admin-guide/sysctl/net.rst +1 -1
index e043c9213388..84e3348a9543 100644
@@ -353,7 +353,7 @@ socket's buffer. It will not take effect unless PF_UNIX flag is specified.
 
 3. /proc/sys/net/ipv4 - IPV4 settings
 -------------------------------------
-Please see: Documentation/networking/ip-sysctl.txt and ipvs-sysctl.txt for
+Please see: Documentation/networking/ip-sysctl.rst and ipvs-sysctl.txt for
 descriptions of these entries.
 
 
Documentation/networking/index.rst +1 -0
index 3efb4608649a..7d133d8dbe2a 100644
@@ -69,6 +69,7 @@ Contents:
    ip_dynaddr
    iphase
    ipsec
+   ip-sysctl
 
 .. only::  subproject and html
 
Documentation/networking/ip-sysctl.rst renamed from Documentation/networking/ip-sysctl.txt +552 -277

1,916 lines not on this page · raw message

Documentation/networking/snmp_counter.rst +1 -1
index 10e11099e74a..4edd0d38779e 100644
@@ -792,7 +792,7 @@ counters to indicate the ACK is skipped in which scenario. The ACK
 would only be skipped if the received packet is either a SYN packet or
 it has no data.
 
-.. _sysctl document: https://www.kernel.org/doc/Documentation/networking/ip-sysctl.txt
+.. _sysctl document: https://www.kernel.org/doc/Documentation/networking/ip-sysctl.rst
 
 * TcpExtTCPACKSkippedSynRecv
 
net/Kconfig +1 -1
index df8d8c9bd021..8b1f85820a6b 100644
@@ -86,7 +86,7 @@ config INET
 	  "Sysctl support" below, you can change various aspects of the
 	  behavior of the TCP/IP code by writing to the (virtual) files in
 	  /proc/sys/net/ipv4/*; the options are explained in the file
-	  <file:Documentation/networking/ip-sysctl.txt>.
+	  <file:Documentation/networking/ip-sysctl.rst>.
 
 	  Short answer: say Y.
 
net/ipv4/Kconfig +1 -1
index 25a8888826b8..5da4733067fb 100644
@@ -49,7 +49,7 @@ config IP_ADVANCED_ROUTER
 
 	  Note that some distributions enable it in startup scripts.
 	  For details about rp_filter strict and loose mode read
-	  <file:Documentation/networking/ip-sysctl.txt>.
+	  <file:Documentation/networking/ip-sysctl.rst>.
 
 	  If unsure, say N here.
 
net/ipv4/icmp.c +1 -1
index fc61f51d87a3..956a806649f7 100644
@@ -853,7 +853,7 @@ static bool icmp_unreach(struct sk_buff *skb)
 		case ICMP_FRAG_NEEDED:
 			/* for documentation of the ip_no_pmtu_disc
 			 * values please see
-			 * Documentation/networking/ip-sysctl.txt
+			 * Documentation/networking/ip-sysctl.rst
 			 */
 			switch (net->ipv4.sysctl_ip_no_pmtu_disc) {
 			default:
Signature · 1 line
2.25.4
#35 lore raw

PATCH 35/38 docs: networking: convert ipv6.txt to ReST

In reply to Mauro Carvalho Chehab

Not much to be done here:

- add SPDX header;
- add a document title;
- mark a literal as such, in order to avoid a warning;
- add to networking/index.rst.

---
 Documentation/admin-guide/kernel-parameters.txt | 6 +++---
 Documentation/networking/index.rst              | 1 +
 Documentation/networking/{ipv6.txt => ipv6.rst} | 8 +++++++-
 net/ipv6/Kconfig                                | 2 +-
 4 files changed, 12 insertions(+), 5 deletions(-)
 rename Documentation/networking/{ipv6.txt => ipv6.rst} (93%)
Documentation/admin-guide/kernel-parameters.txt +3 -3
index ef9779398cee..e84951d80e6f 100644
@@ -356,7 +356,7 @@
 			      shot down by NMI
 
 	autoconf=	[IPV6]
-			See Documentation/networking/ipv6.txt.
+			See Documentation/networking/ipv6.rst.
 
 	show_lapic=	[APIC,X86] Advanced Programmable Interrupt Controller
 			Limit apic dumping. The parameter defines the maximal
@@ -875,7 +875,7 @@
 			miss to occur.
 
 	disable=	[IPV6]
-			See Documentation/networking/ipv6.txt.
+			See Documentation/networking/ipv6.rst.
 
 	hardened_usercopy=
                         [KNL] Under CONFIG_HARDENED_USERCOPY, whether
@@ -915,7 +915,7 @@
 			to workaround buggy firmware.
 
 	disable_ipv6=	[IPV6]
-			See Documentation/networking/ipv6.txt.
+			See Documentation/networking/ipv6.rst.
 
 	disable_mtrr_cleanup [X86]
 			The kernel tries to adjust MTRR layout from continuous
Documentation/networking/index.rst +1 -0
index 7d133d8dbe2a..709675464e51 100644
@@ -70,6 +70,7 @@ Contents:
    iphase
    ipsec
    ip-sysctl
+   ipv6
 
 .. only::  subproject and html
 
Documentation/networking/ipv6.rst renamed from Documentation/networking/ipv6.txt +7 -1
similarity index 93%
rename from Documentation/networking/ipv6.txt
rename to Documentation/networking/ipv6.rst
index 6cd74fa55358..ba09c2f2dcc7 100644
@@ -1,9 +1,15 @@
+.. SPDX-License-Identifier: GPL-2.0
+
+====
+IPv6
+====
+
 
 Options for the ipv6 module are supplied as parameters at load time.
 
 Module options may be given as command line arguments to the insmod
 or modprobe command, but are usually specified in either
-/etc/modules.d/*.conf configuration files, or in a distro-specific
+``/etc/modules.d/*.conf`` configuration files, or in a distro-specific
 configuration file.
 
 The available ipv6 module parameters are listed below.  If a parameter
net/ipv6/Kconfig +1 -1
index 2ccaee98fddb..5a6111da26c4 100644
@@ -13,7 +13,7 @@ menuconfig IPV6
 	  For general information about IPv6, see
 	  <https://en.wikipedia.org/wiki/IPv6>.
 	  For specific information about IPv6 under Linux, see
-	  Documentation/networking/ipv6.txt and read the HOWTO at
+	  Documentation/networking/ipv6.rst and read the HOWTO at
 	  <http://www.tldp.org/HOWTO/Linux+IPv6-HOWTO/>
 
 	  To compile this protocol support as a module, choose M here: the
Signature · 1 line
2.25.4
#36 lore raw

PATCH 36/38 docs: networking: convert ipvlan.txt to ReST

In reply to Mauro Carvalho Chehab

- add SPDX header;
- adjust titles and chapters, adding proper markups;
- mark code blocks and literals as such;
- adjust identation, whitespaces and blank lines;
- add to networking/index.rst.

---
 Documentation/networking/index.rst            |   1 +
 .../networking/{ipvlan.txt => ipvlan.rst}     | 159 +++++++++++-------
 2 files changed, 102 insertions(+), 58 deletions(-)
 rename Documentation/networking/{ipvlan.txt => ipvlan.rst} (54%)
Documentation/networking/index.rst +1 -0
index 709675464e51..54dee1575b54 100644
@@ -71,6 +71,7 @@ Contents:
    ipsec
    ip-sysctl
    ipv6
+   ipvlan
 
 .. only::  subproject and html
 
Documentation/networking/ipvlan.rst renamed from Documentation/networking/ipvlan.txt +101 -58

233 lines not on this page · raw message

Signature · 1 line
2.25.4
#37 lore raw

PATCH 37/38 docs: networking: convert ipvs-sysctl.txt to ReST

In reply to Mauro Carvalho Chehab

- add SPDX header;
- add a document title;
- mark lists as such;
- mark code blocks and literals as such;
- adjust identation, whitespaces and blank lines;
- add to networking/index.rst.

---
 Documentation/admin-guide/sysctl/net.rst      |   4 +-
 Documentation/networking/index.rst            |   1 +
 .../{ipvs-sysctl.txt => ipvs-sysctl.rst}      | 180 +++++++++---------
 MAINTAINERS                                   |   2 +-
 4 files changed, 98 insertions(+), 89 deletions(-)
 rename Documentation/networking/{ipvs-sysctl.txt => ipvs-sysctl.rst} (62%)
Documentation/admin-guide/sysctl/net.rst +2 -2
index 84e3348a9543..2ad1b77a7182 100644
@@ -353,8 +353,8 @@ socket's buffer. It will not take effect unless PF_UNIX flag is specified.
 
 3. /proc/sys/net/ipv4 - IPV4 settings
 -------------------------------------
-Please see: Documentation/networking/ip-sysctl.rst and ipvs-sysctl.txt for
-descriptions of these entries.
+Please see: Documentation/networking/ip-sysctl.rst and
+Documentation/admin-guide/sysctl/net.rst for descriptions of these entries.
 
 
 4. Appletalk
Documentation/networking/index.rst +1 -0
index 54dee1575b54..bbd4e0041457 100644
@@ -72,6 +72,7 @@ Contents:
    ip-sysctl
    ipv6
    ipvlan
+   ipvs-sysctl
 
 .. only::  subproject and html
 
Documentation/networking/ipvs-sysctl.rst renamed from Documentation/networking/ipvs-sysctl.txt +94 -86

263 lines not on this page · raw message

MAINTAINERS +1 -1
index 3764697a6002..2828723f0d4d 100644
@@ -8957,7 +8957,7 @@ L:	[email protected]
 S:	Maintained
 T:	git git://git.kernel.org/pub/scm/linux/kernel/git/horms/ipvs-next.git
 T:	git git://git.kernel.org/pub/scm/linux/kernel/git/horms/ipvs.git
-F:	Documentation/networking/ipvs-sysctl.txt
+F:	Documentation/networking/ipvs-sysctl.rst
 F:	include/net/ip_vs.h
 F:	include/uapi/linux/ip_vs.h
 F:	net/netfilter/ipvs/
Signature · 1 line
2.25.4
#39 lore raw

PATCH 38/38 docs: networking: convert kcm.txt to ReST

In reply to Mauro Carvalho Chehab

- add SPDX header;
- adjust titles and chapters, adding proper markups;
- mark code blocks and literals as such;
- adjust identation, whitespaces and blank lines;
- add to networking/index.rst.

---
 Documentation/networking/index.rst            |  1 +
 Documentation/networking/{kcm.txt => kcm.rst} | 83 ++++++++++---------
 2 files changed, 45 insertions(+), 39 deletions(-)
 rename Documentation/networking/{kcm.txt => kcm.rst} (84%)
Documentation/networking/index.rst +1 -0
index bbd4e0041457..e1ff08b94d90 100644
@@ -73,6 +73,7 @@ Contents:
    ipv6
    ipvlan
    ipvs-sysctl
+   kcm
 
 .. only::  subproject and html
 
Documentation/networking/kcm.rst renamed from Documentation/networking/kcm.txt +44 -39

179 lines not on this page · raw message

Signature · 1 line
2.25.4
maintainer
#40 lore raw
In reply to Mauro Carvalho Chehab

From: Mauro Carvalho Chehab <[email protected]>
Date: Tue, 28 Apr 2020 00:01:15 +0200

Quoted 6 lines

There are very few documents upstream that aren't converted upstream.

This series convert part of the networking text files into ReST. It is part of a bigger set of patches, which were split on parts, in order to make reviewing task easier.

Quoted 8 lines

The full series (including those ones) are at:

https://git.linuxtv.org/mchehab/experimental.git/log/?h=net-docs

And the documents, converted to HTML via the building system are at:

https://www.infradead.org/~mchehab/kernel_docs/networking/

These look good as far as I can tell.

Jon, do you mind if I merge this via the networking tree?

Thanks.

maintainer
#41 lore raw
Quoted 1 line · On Tue, 28 Apr 2020 13:11:43 -0700 (PDT) David Miller <[email protected]>…

Jon, do you mind if I merge this via the networking tree?

Not at all, that's what I was expecting you would do.

Thanks,

jon

maintainer
#42 lore raw
In reply to Mauro Carvalho Chehab

From: Mauro Carvalho Chehab <[email protected]>
Date: Tue, 28 Apr 2020 00:01:15 +0200

Quoted 6 lines

There are very few documents upstream that aren't converted upstream.

This series convert part of the networking text files into ReST. It is part of a bigger set of patches, which were split on parts, in order to make reviewing task easier.

Quoted 8 lines

The full series (including those ones) are at:

https://git.linuxtv.org/mchehab/experimental.git/log/?h=net-docs

And the documents, converted to HTML via the building system are at:

https://www.infradead.org/~mchehab/kernel_docs/networking/

Series applied to net-next, thank you.