igc: Reject NFC rules with multiple matches
Subsystems (2)
RFC PATCH 1/1 igc: Reject NFC rules with multiple matches
The way rx queue assignment based on mac address, ethetype and vlan priority filtering operates in I225 doesn't allow us to properly support NFC rules with multiple matches.
Consider the following example which assigns to queue 2 frames matching the address MACADDR *and* ethertype ETYPE.
$ ethtool -N eth0 flow-type ether dst <MACADDR> proto <ETYPE> queue 2
When such rule is applied, we have 2 unwanted behaviors:
1) Any frame matching MACADDR will be assigned to queue 2. It doesn't matter the ETYPE value.
2) Any accepted frame that has ethertype equals to ETYPE, no matter the mac address, will be assigned to queue 2 as well.
While we could fix 1) by not enabling queue assignment on the MAC address filter, 2) would still happen.
In current code, multiple-match filters are accepted by the driver, even though it doesn't support them properly. This patch adds a check for multiple-match rules in igc_ethtool_is_nfc_rule_valid() so they are rejected.
---
Hi folks,
This patch was originally included in the series "igc: Fixes to NFC support code", but since it changes the way the driver interacts with user space, I decided to sent it separately as RFC to collect your opinions.
The patch description gives a detailed explanation about the issue. The bottom line is: Current code silently accepts a configuration that is not supported. This patch changes the driver so EOPNOTSUPP is returned instead of success.
What I'd like to get your feedback on is:
Is this considered an user-kernel break? If so, what would be the best way to move forward. Keep accepting the configuration but warn user via log message about not supporting it?
Thank you,
Andre
--- drivers/net/ethernet/intel/igc/igc_ethtool.c | 9 ++++----- 1 file changed, 4 insertions(+), 5 deletions(-)
drivers/net/ethernet/intel/igc/igc_ethtool.c +4 -5
@@ -1222,8 +1222,8 @@ static void igc_ethtool_init_nfc_rule(struct igc_nfc_rule *rule,* @adapter: Pointer to adapter. * @rule: Rule under evaluation. * -* Rules with both destination and source MAC addresses are considered invalid -* since the driver doesn't support them. +* The driver doesn't support rules with multiple matches so if more than +* one bit in filter flags is set, @rule is considered invalid. * * Also, if there is already another rule with the same filter in a different * location, @rule is considered invalid.
@@ -1244,9 +1244,8 @@ static int igc_ethtool_check_nfc_rule(struct igc_adapter *adapter,return -EINVAL ; } -if (flags &IGC_FILTER_FLAG_DST_MAC_ADDR && - flags &IGC_FILTER_FLAG_SRC_MAC_ADDR ) { -netdev_dbg (dev,"Filters with both dst and src are not supported" ); +if (flags & (flags -1 )) { +netdev_dbg (dev,"Rule with multiple matches not supported" );return -EOPNOTSUPP ; }
Signature · 1 line
2.26.0
RFC PATCH 1/1 igc: Reject NFC rules with multiple matches
Quoted 37 lines
The way rx queue assignment based on mac address, ethetype and vlan priority filtering operates in I225 doesn't allow us to properly support NFC rules with multiple matches.
Consider the following example which assigns to queue 2 frames matching the address MACADDR *and* ethertype ETYPE.
$ ethtool -N eth0 flow-type ether dst <MACADDR> proto <ETYPE> queue 2When such rule is applied, we have 2 unwanted behaviors:
1) Any frame matching MACADDR will be assigned to queue 2. It doesn't matter the ETYPE value.
2) Any accepted frame that has ethertype equals to ETYPE, no matter the mac address, will be assigned to queue 2 as well.
While we could fix 1) by not enabling queue assignment on the MAC address filter, 2) would still happen.
In current code, multiple-match filters are accepted by the driver, even though it doesn't support them properly. This patch adds a check for multiple-match rules in
igc_ethtool_is_nfc_rule_valid()so they are rejected.Signed-off-by Andre Guedes <[email protected]>---
Hi folks,This patch was originally included in the series "igc: Fixes to NFC support code", but since it changes the way the driver interacts with user space, I decided to sent it separately as RFC to collect your opinions.
The patch description gives a detailed explanation about the issue. The bottom line is: Current code silently accepts a configuration that is not supported. This patch changes the driver so EOPNOTSUPP is returned instead of success.
Quoted 5 lines
What I'd like to get your feedback on is:
Is this considered an user-kernel break? If so, what would be the best way to move forward. Keep accepting the configuration but warn user via log message about not supporting it?
I'm assuming this is not considered a user-kernel break since I could spot at least one similar change in igb driver (b4a38d4276e1). I'll rebase and send this as PATCH.
- Andre