Skip to contentSkip to conversation

add SPI_SIMPLEX_RX/SPI_3WIRE_RX support for spi-stm32f4

PATCH In review [email protected] 2 participants 2 messages Apr 30, 2020

Subsystems (3)
lore
Share & tools
lore
#0 lore raw

PATCH 4/4 add SPI_SIMPLEX_RX/SPI_3WIRE_RX support for spi-stm32f4

From: dillon min <[email protected]>

add SPI_SIMPLEX_RX/SPI_3WIRE_RX in spi-stm32f4.c for SPI_SIMPLEX_RX , as we running kernel in sdram, so that the performance is not as good as internal flash, need add send dummy data out while in rx, otherwise will get many overrun errors.

---
 drivers/spi/spi-stm32.c | 26 ++++++++++++++++++++++----
 1 file changed, 22 insertions(+), 4 deletions(-)
drivers/spi/spi-stm32.c +22 -4
index 44ac6eb3..680cede 100644
@@ -388,6 +388,10 @@ static int stm32h7_spi_get_fifo_size(struct stm32_spi *spi)
 	return count;
 }
 
+static void stm32f4_spi_tx_dummy(struct stm32_spi *spi)
+{
+	writeb_relaxed(0x55, spi->base + STM32F4_SPI_DR);
+}
 /**
  * stm32f4_spi_get_bpw_mask - Return bits per word mask
  * @spi: pointer to the spi controller data structure
@@ -811,7 +815,9 @@ static irqreturn_t stm32f4_spi_irq_event(int irq, void *dev_id)
 		mask |= STM32F4_SPI_SR_TXE;
 	}
 
-	if (!spi->cur_usedma && spi->cur_comm == SPI_FULL_DUPLEX) {
+	if (!spi->cur_usedma && (spi->cur_comm == SPI_FULL_DUPLEX ||
+				 spi->cur_comm == SPI_SIMPLEX_RX ||
+				 spi->cur_comm == SPI_3WIRE_RX)) {
 		/* TXE flag is set and is handled when RXNE flag occurs */
 		sr &= ~STM32F4_SPI_SR_TXE;
 		mask |= STM32F4_SPI_SR_RXNE | STM32F4_SPI_SR_OVR;
@@ -850,8 +856,10 @@ static irqreturn_t stm32f4_spi_irq_event(int irq, void *dev_id)
 		stm32f4_spi_read_rx(spi);
 		if (spi->rx_len == 0)
 			end = true;
-		else /* Load data for discontinuous mode */
+		else if (spi->tx_buf)/* Load data for discontinuous mode */
 			stm32f4_spi_write_tx(spi);
+		else if (spi->cur_comm == SPI_SIMPLEX_RX)
+			stm32f4_spi_tx_dummy(spi);
 	}
 
 end_irq:
@@ -1151,7 +1159,9 @@ static int stm32f4_spi_transfer_one_irq(struct stm32_spi *spi)
 	/* Enable the interrupts relative to the current communication mode */
 	if (spi->cur_comm == SPI_SIMPLEX_TX || spi->cur_comm == SPI_3WIRE_TX) {
 		cr2 |= STM32F4_SPI_CR2_TXEIE;
-	} else if (spi->cur_comm == SPI_FULL_DUPLEX) {
+	} else if (spi->cur_comm == SPI_FULL_DUPLEX ||
+				spi->cur_comm == SPI_SIMPLEX_RX ||
+				spi->cur_comm == SPI_3WIRE_RX) {
 		/* In transmit-only mode, the OVR flag is set in the SR register
 		 * since the received data are never read. Therefore set OVR
 		 * interrupt only when rx buffer is available.
@@ -1170,6 +1180,8 @@ static int stm32f4_spi_transfer_one_irq(struct stm32_spi *spi)
 	/* starting data transfer when buffer is loaded */
 	if (spi->tx_buf)
 		stm32f4_spi_write_tx(spi);
+	else if (spi->cur_comm == SPI_SIMPLEX_RX)
+		stm32f4_spi_tx_dummy(spi);
 
 	spin_unlock_irqrestore(&spi->lock, flags);
 
@@ -1462,9 +1474,15 @@ static int stm32f4_spi_set_mode(struct stm32_spi *spi, unsigned int comm_type)
 		stm32_spi_set_bits(spi, STM32F4_SPI_CR1,
 					STM32F4_SPI_CR1_BIDIMODE |
 					STM32F4_SPI_CR1_BIDIOE);
-	} else if (comm_type == SPI_FULL_DUPLEX) {
+	} else if (comm_type == SPI_FULL_DUPLEX ||
+				comm_type == SPI_SIMPLEX_RX) {
 		stm32_spi_clr_bits(spi, STM32F4_SPI_CR1,
 					STM32F4_SPI_CR1_BIDIMODE |
+					STM32F4_SPI_CR1_RXONLY);
+	} else if (comm_type == SPI_3WIRE_RX) {
+		stm32_spi_set_bits(spi, STM32F4_SPI_CR1,
+					STM32F4_SPI_CR1_BIDIMODE);
+		stm32_spi_clr_bits(spi, STM32F4_SPI_CR1,
 					STM32F4_SPI_CR1_BIDIOE);
 	} else {
 		return -EINVAL;
Signature · 1 line
2.7.4
maintainer
#1 lore raw
Quoted 7 lines · On Thu, Apr 30, 2020 at 05:44:00PM +0800, [email protected] wrote:

From: dillon min <[email protected]>

add SPI_SIMPLEX_RX/SPI_3WIRE_RX in spi-stm32f4.c for SPI_SIMPLEX_RX , as we running kernel in sdram, so that the performance is not as good as internal flash, need add send dummy data out while in rx, otherwise will get many overrun errors.

I only have patch 4 here, what's going on with dependencies?