Skip to contentSkip to conversation

PCI: brcmstb: Some minor fixes/features

PATCH Superseded Jim Quinlan 3 participants 9 messages May 1, 2020 – May 5, 2020

Subsystems (6)

v2 of 3 Superseded Latest is v3 →

lore
Share & tools
lore
#0 lore raw

v2 cover PCI: brcmstb: Some minor fixes/features

v2 -- Dropped commit concerning CRS.
-- Chanded new prop 'brcm,aspm-en-l0s' to 'aspm-no-l0s'. -- Capitalize first letter in commit subject line; spelling.

v1 -- original

Jim Quinlan (4):
PCI: brcmstb: Don't clk_put() a managed clock
PCI: brcmstb: Fix window register offset from 4 to 8
dt-bindings: PCI: brcmstb: New prop 'aspm-no-l0s'
PCI: brcmstb: Disable L0s component of ASPM if requested

 .../bindings/pci/brcm,stb-pcie.yaml           |  4 ++++
 drivers/pci/controller/pcie-brcmstb.c         | 19 +++++++++++++++----
 2 files changed, 19 insertions(+), 4 deletions(-)
Signature · 1 line
2.17.1
#1 lore raw

PATCH v2 1/4 PCI: brcmstb: Don't clk_put() a managed clock

From: Jim Quinlan <[email protected]>

clk_put() was being invoked on a clock obtained by devm_clk_get_optional().

---
 drivers/pci/controller/pcie-brcmstb.c | 1 -
 1 file changed, 1 deletion(-)
drivers/pci/controller/pcie-brcmstb.c +0 -1
index 6d79d14527a6..454917ee9241 100644
@@ -899,7 +899,6 @@ static void __brcm_pcie_remove(struct brcm_pcie *pcie)
 	brcm_msi_remove(pcie);
 	brcm_pcie_turn_off(pcie);
 	clk_disable_unprepare(pcie->clk);
-	clk_put(pcie->clk);
 }
 
 static int brcm_pcie_remove(struct platform_device *pdev)
Signature · 1 line
2.17.1
Acked-by on v2 1/4
#2 lore raw

Re: [PATCH v2 1/4] PCI: brcmstb: Don't clk_put() a managed clock

Quoted 8 lines · Jim Quinlan

From: Jim Quinlan <[email protected]>

clk_put() was being invoked on a clock obtained by devm_clk_get_optional().

---

Regards,
Nicolas

Quoted 16 lines
 drivers/pci/controller/pcie-brcmstb.c | 1 -
 1 file changed, 1 deletion(-)
drivers/pci/controller/pcie-brcmstb.c +0 -1
index 6d79d14527a6..454917ee9241 100644
@@ -899,7 +899,6 @@ static void __brcm_pcie_remove(struct brcm_pcie *pcie)
 	brcm_msi_remove(pcie);
 	brcm_pcie_turn_off(pcie);
 	clk_disable_unprepare(pcie->clk);
-	clk_put(pcie->clk);
 }
 
 static int brcm_pcie_remove(struct platform_device *pdev)
#3 lore raw

PATCH v2 2/4 PCI: brcmstb: Fix window register offset from 4 to 8

In reply to Jim Quinlan

From: Jim Quinlan <[email protected]>

The outbound memory window registers were being referenced with an incorrect stride offset. This probably wasn't noticed previously as there was likely only one such window employed.

Fixes c0452137034b ("PCI: brcmstb: Add Broadcom STB PCIe host controller driver")
---
 drivers/pci/controller/pcie-brcmstb.c | 4 ++--
 1 file changed, 2 insertions(+), 2 deletions(-)
drivers/pci/controller/pcie-brcmstb.c +2 -2
index 454917ee9241..5b0dec5971b8 100644
@@ -54,11 +54,11 @@
 
 #define PCIE_MISC_CPU_2_PCIE_MEM_WIN0_LO		0x400c
 #define PCIE_MEM_WIN0_LO(win)	\
-		PCIE_MISC_CPU_2_PCIE_MEM_WIN0_LO + ((win) * 4)
+		PCIE_MISC_CPU_2_PCIE_MEM_WIN0_LO + ((win) * 8)
 
 #define PCIE_MISC_CPU_2_PCIE_MEM_WIN0_HI		0x4010
 #define PCIE_MEM_WIN0_HI(win)	\
-		PCIE_MISC_CPU_2_PCIE_MEM_WIN0_HI + ((win) * 4)
+		PCIE_MISC_CPU_2_PCIE_MEM_WIN0_HI + ((win) * 8)
 
 #define PCIE_MISC_RC_BAR1_CONFIG_LO			0x402c
 #define  PCIE_MISC_RC_BAR1_CONFIG_LO_SIZE_MASK		0x1f
Signature · 1 line
2.17.1
Acked-by on v2 2/4
#4 lore raw

Re: [PATCH v2 2/4] PCI: brcmstb: Fix window register offset from 4 to 8

Quoted 6 lines · Jim Quinlan

From: Jim Quinlan <[email protected]>

The outbound memory window registers were being referenced with an incorrect stride offset. This probably wasn't noticed previously as there was likely only one such window employed.

Quoted 6 lines
Fixes c0452137034b ("PCI: brcmstb: Add Broadcom STB PCIe host controller

driver")
---

Regards,
Nicolas

Quoted 22 lines
 drivers/pci/controller/pcie-brcmstb.c | 4 ++--
 1 file changed, 2 insertions(+), 2 deletions(-)
drivers/pci/controller/pcie-brcmstb.c +2 -2
index 454917ee9241..5b0dec5971b8 100644
@@ -54,11 +54,11 @@
 
 #define PCIE_MISC_CPU_2_PCIE_MEM_WIN0_LO		0x400c
 #define PCIE_MEM_WIN0_LO(win)	\
-		PCIE_MISC_CPU_2_PCIE_MEM_WIN0_LO + ((win) * 4)
+		PCIE_MISC_CPU_2_PCIE_MEM_WIN0_LO + ((win) * 8)
 
 #define PCIE_MISC_CPU_2_PCIE_MEM_WIN0_HI		0x4010
 #define PCIE_MEM_WIN0_HI(win)	\
-		PCIE_MISC_CPU_2_PCIE_MEM_WIN0_HI + ((win) * 4)
+		PCIE_MISC_CPU_2_PCIE_MEM_WIN0_HI + ((win) * 8)
 
 #define PCIE_MISC_RC_BAR1_CONFIG_LO			0x402c
 #define  PCIE_MISC_RC_BAR1_CONFIG_LO_SIZE_MASK		0x1f
#5 lore raw

PATCH v2 3/4 dt-bindings: PCI: brcmstb: New prop 'aspm-no-l0s'

In reply to Jim Quinlan

From: Jim Quinlan <[email protected]>

For various reasons, one may want to disable the ASPM L0s capability.

---
 Documentation/devicetree/bindings/pci/brcm,stb-pcie.yaml | 4 ++++
 1 file changed, 4 insertions(+)
Documentation/devicetree/bindings/pci/brcm,stb-pcie.yaml +4 -0
index 77d3e81a437b..084e4cf68b95 100644
@@ -56,6 +56,10 @@ properties:
     description: Indicates usage of spread-spectrum clocking.
     type: boolean
 
+  aspm-no-l0s:
+    description: Disables ASPM L0s capability.
+    type: boolean
+
 required:
   - reg
   - dma-ranges
Signature · 1 line
2.17.1
#6 lore raw

Re: [PATCH v2 3/4] dt-bindings: PCI: brcmstb: New prop 'aspm-no-l0s'

Quoted 16 lines · Jim Quinlan

From: Jim Quinlan <[email protected]>

For various reasons, one may want to disable the ASPM L0s capability.

---
 Documentation/devicetree/bindings/pci/brcm,stb-pcie.yaml | 4 ++++
 1 file changed, 4 insertions(+)
Documentation/devicetree/bindings/pci/brcm,stb-pcie.yaml +0 -0
index 77d3e81a437b..084e4cf68b95 100644

Documentation/devicetree/bindings/pci/brcm,stb-pcie.yaml properties: · line 61

Quoted 6 lines
Documentation/devicetree/bindings/pci/brcm,stb-pcie.yaml +3 -0
@@ -56,6 +56,10 @@ properties:
     description: Indicates usage of spread-spectrum clocking.
     type: boolean
 
+  aspm-no-l0s:
+    description: Disables ASPM L0s capability.
+    type: boolean

Copied from rockchip-pcie-host.txt? Let's make this a standard property. It should be documented here[1].

Then this doc just needs 'aspm-no-l0s: true' to indicate you are using it.

Rob

[1] https://github.com/devicetree-org/dt-schema/blob/master/schemas/pci/pci-bus.yaml

#7 lore raw

PATCH v2 4/4 PCI: brcmstb: Disable L0s component of ASPM if requested

In reply to Jim Quinlan

From: Jim Quinlan <[email protected]>

Some informal internal experiments has shown that the BrcmSTB ASPM L0s savings may introduce an undesirable noise signal on some customers' boards. In addition, L0s was found lacking in realized power savings, especially relative to the L1 ASPM component. This is BrcmSTB's experience and may not hold for others. At any rate, if the 'aspm-no-l0s' property is present L0s will be disabled.

---
 drivers/pci/controller/pcie-brcmstb.c | 14 +++++++++++++-
 1 file changed, 13 insertions(+), 1 deletion(-)
drivers/pci/controller/pcie-brcmstb.c +13 -1
index 5b0dec5971b8..73020b4ff090 100644
@@ -41,6 +41,9 @@
 #define PCIE_RC_CFG_PRIV1_ID_VAL3			0x043c
 #define  PCIE_RC_CFG_PRIV1_ID_VAL3_CLASS_CODE_MASK	0xffffff
 
+#define PCIE_RC_CFG_PRIV1_LINK_CAPABILITY			0x04dc
+#define  PCIE_RC_CFG_PRIV1_LINK_CAPABILITY_ASPM_SUPPORT_MASK	0xc00
+
 #define PCIE_RC_DL_MDIO_ADDR				0x1100
 #define PCIE_RC_DL_MDIO_WR_DATA				0x1104
 #define PCIE_RC_DL_MDIO_RD_DATA				0x1108
@@ -693,7 +696,7 @@ static int brcm_pcie_setup(struct brcm_pcie *pcie)
 	int num_out_wins = 0;
 	u16 nlw, cls, lnksta;
 	int i, ret;
-	u32 tmp;
+	u32 tmp, aspm_support;
 
 	/* Reset the bridge */
 	brcm_pcie_bridge_sw_init_set(pcie, 1);
@@ -803,6 +806,15 @@ static int brcm_pcie_setup(struct brcm_pcie *pcie)
 		num_out_wins++;
 	}
 
+	/* Don't advertise L0s capability if 'aspm-no-l0s' */
+	aspm_support = PCIE_LINK_STATE_L1;
+	if (!of_property_read_bool(pcie->np, "aspm-no-l0s"))
+		aspm_support |= PCIE_LINK_STATE_L0S;
+	tmp = readl(base + PCIE_RC_CFG_PRIV1_LINK_CAPABILITY);
+	u32p_replace_bits(&tmp, aspm_support,
+		PCIE_RC_CFG_PRIV1_LINK_CAPABILITY_ASPM_SUPPORT_MASK);
+	writel(tmp, base + PCIE_RC_CFG_PRIV1_LINK_CAPABILITY);
+
 	/*
 	 * For config space accesses on the RC, show the right class for
 	 * a PCIe-PCIe bridge (the default setting is to be EP mode).
Signature · 1 line
2.17.1
Acked-by on v2 4/4
#8 lore raw

Re: [PATCH v2 4/4] PCI: brcmstb: Disable L0s component of ASPM if requested

Quoted 11 lines · Jim Quinlan

From: Jim Quinlan <[email protected]>

Some informal internal experiments has shown that the BrcmSTB ASPM L0s savings may introduce an undesirable noise signal on some customers' boards. In addition, L0s was found lacking in realized power savings, especially relative to the L1 ASPM component. This is BrcmSTB's experience and may not hold for others. At any rate, if the 'aspm-no-l0s' property is present L0s will be disabled.

Modulo the new generic dt property:

Regards,
Nicolas

Quoted 44 lines
---
 drivers/pci/controller/pcie-brcmstb.c | 14 +++++++++++++-
 1 file changed, 13 insertions(+), 1 deletion(-)
drivers/pci/controller/pcie-brcmstb.c +13 -1
index 5b0dec5971b8..73020b4ff090 100644
@@ -41,6 +41,9 @@
 #define PCIE_RC_CFG_PRIV1_ID_VAL3			0x043c
 #define  PCIE_RC_CFG_PRIV1_ID_VAL3_CLASS_CODE_MASK	0xffffff
 
+#define PCIE_RC_CFG_PRIV1_LINK_CAPABILITY			0x04dc
+#define  PCIE_RC_CFG_PRIV1_LINK_CAPABILITY_ASPM_SUPPORT_MASK	0xc00
+
 #define PCIE_RC_DL_MDIO_ADDR				0x1100
 #define PCIE_RC_DL_MDIO_WR_DATA				0x1104
 #define PCIE_RC_DL_MDIO_RD_DATA				0x1108
@@ -693,7 +696,7 @@ static int brcm_pcie_setup(struct brcm_pcie *pcie)
 	int num_out_wins = 0;
 	u16 nlw, cls, lnksta;
 	int i, ret;
-	u32 tmp;
+	u32 tmp, aspm_support;
 
 	/* Reset the bridge */
 	brcm_pcie_bridge_sw_init_set(pcie, 1);
@@ -803,6 +806,15 @@ static int brcm_pcie_setup(struct brcm_pcie *pcie)
 		num_out_wins++;
 	}
 
+	/* Don't advertise L0s capability if 'aspm-no-l0s' */
+	aspm_support = PCIE_LINK_STATE_L1;
+	if (!of_property_read_bool(pcie->np, "aspm-no-l0s"))
+		aspm_support |= PCIE_LINK_STATE_L0S;
+	tmp = readl(base + PCIE_RC_CFG_PRIV1_LINK_CAPABILITY);
+	u32p_replace_bits(&tmp, aspm_support,
+		PCIE_RC_CFG_PRIV1_LINK_CAPABILITY_ASPM_SUPPORT_MASK);
+	writel(tmp, base + PCIE_RC_CFG_PRIV1_LINK_CAPABILITY);
+
 	/*
 	 * For config space accesses on the RC, show the right class for
 	 * a PCIe-PCIe bridge (the default setting is to be EP mode).