u-boot support for ODROID-C4
Subsystems (2)
cover u-boot support for ODROID-C4
Hi,
these two patches add initial u-boot support for Hardkernel ODROID-C4.
https://wiki.odroid.com/odroid-c4/odroid-c4
Beniamino Galvani (2):
arm: dts: import ODROID-C4 device tree
boards: amlogic: add ODROID-C4 support
arch/arm/dts/Makefile | 1 + arch/arm/dts/meson-sm1-odroid-c4.dts | 399 +++++++++++++++++++++++++++ board/amlogic/odroid-c4/MAINTAINERS | 6 + board/amlogic/odroid-c4/Makefile | 3 + board/amlogic/odroid-c4/README | 83 ++++++ board/amlogic/odroid-c4/odroid-c4.c | 17 ++ configs/odroid-c4_defconfig | 63 +++++ 7 files changed, 572 insertions(+) create mode 100644 arch/arm/dts/meson-sm1-odroid-c4.dts create mode 100644 board/amlogic/odroid-c4/MAINTAINERS create mode 100644 board/amlogic/odroid-c4/Makefile create mode 100644 board/amlogic/odroid-c4/README create mode 100644 board/amlogic/odroid-c4/odroid-c4.c create mode 100644 configs/odroid-c4_defconfig
Signature · 1 line
2.25.1
PATCH 1/2 arm: dts: import ODROID-C4 device tree
Import the device tree for ODROID-C4 as submitted in [1].
[1] https://lkml.org/lkml/2020/4/24/535
--- arch/arm/dts/Makefile | 1 + arch/arm/dts/meson-sm1-odroid-c4.dts | 399 +++++++++++++++++++++++++++ 2 files changed, 400 insertions(+) create mode 100644 arch/arm/dts/meson-sm1-odroid-c4.dts
arch/arm/dts/Makefile +1 -0
@@ -161,6 +161,7 @@ dtb-$(CONFIG_ARCH_MESON) += \ meson-g12b-odroid-n2.dtb \ meson-g12b-a311d-khadas-vim3.dtb \ meson-sm1-khadas-vim3l.dtb \ + meson-sm1-odroid-c4.dtb \ meson-sm1-sei610.dtb dtb-$(CONFIG_TEGRA) += tegra20-harmony.dtb \ tegra20-medcom-wide.dtb \
arch/arm/dts/meson-sm1-odroid-c4.dts new file +399 -0
399 lines not on this page · raw message
Signature · 1 line
2.25.1
PATCH 2/2 boards: amlogic: add ODROID-C4 support
In reply to Beniamino GalvaniIntroduce support for ODROID-C4, a single board computer manufactured by Hardkernel Co. Ltd with the following specifications:
- Amlogic S905X3 ARM Cortex-A55 quad-core SoC
- 4GiB DDR4 SDRAM
- Gigabit Ethernet (External Realtek RTL8211F PHY)
- 4 x USB 3.0 Host ports
- 1 x USB 2.0 OTG port
- HDMI 2.0
- eMMC
- SDcard
- 40-pin GPIO header
- Infrared receiver
--- board/amlogic/odroid-c4/MAINTAINERS | 6 +++ board/amlogic/odroid-c4/Makefile | 3 ++ board/amlogic/odroid-c4/README | 83 +++++++++++++++++++++++++++++ board/amlogic/odroid-c4/odroid-c4.c | 17 ++++++ configs/odroid-c4_defconfig | 63 ++++++++++++++++++++++ 5 files changed, 172 insertions(+) create mode 100644 board/amlogic/odroid-c4/MAINTAINERS create mode 100644 board/amlogic/odroid-c4/Makefile create mode 100644 board/amlogic/odroid-c4/README create mode 100644 board/amlogic/odroid-c4/odroid-c4.c create mode 100644 configs/odroid-c4_defconfig
board/amlogic/odroid-c4/MAINTAINERS new file +6 -0
@@ -0,0 +1,6 @@ +ODROID-C4 +M: Beniamino Galvani <[email protected]> +S: Maintained +L: u-boot-amlogic at groups.io +F: board/amlogic/odroid-c4/ +F: configs/odroid-c4_defconfig
board/amlogic/odroid-c4/Makefile new file +3 -0
@@ -0,0 +1,3 @@ +# SPDX-License-Identifier: GPL-2.0+ + +obj-y := odroid-c4.o
board/amlogic/odroid-c4/README new file +83 -0
83 lines not on this page · raw message
board/amlogic/odroid-c4/odroid-c4.c new file +17 -0
@@ -0,0 +1,17 @@ +// SPDX-License-Identifier: GPL-2.0+ +/* +* Copyright (C) 2016 BayLibre, SAS +*/ + +#include <common.h> +#include <dm.h> +#include <asm/arch/eth.h> + +int misc_init_r (void ) +{ +meson_eth_init (PHY_INTERFACE_MODE_RGMII ,0 ); + +meson_generate_serial_ethaddr (); + +return 0 ; +}
configs/odroid-c4_defconfig new file +63 -0
63 lines not on this page · raw message
Signature · 1 line
2.25.1
cover u-boot support for ODROID-C4
In reply to Beniamino GalvaniHi Beniamino,
Quoted 3 lines · Beniamino Galvani
Hi,
these two patches add initial u-boot support for Hardkernel ODROID-C4.
Thanks for the patchset, I already have one in my test tree, by you did beat me by sending it to the list !
Quoted 5 lines
https://wiki.odroid.com/odroid-c4/odroid-c4
Beniamino Galvani (2):
arm: dts: import ODROID-C4 device tree
The DT is not yet applied by kevin, thus I'll prefer waiting it to be accepted and merged in a stable linux tree to keep DT synced.
Quoted 1 line
boards: amlogic: add ODROID-C4 support
Please re-use the w400 board instead of adding a new board, there is no need for a new one until you'll need to add more functionalities.
I know meson_generate_serial_ethaddr() is absent from w400, I'll add it shortly.
Neil
Quoted 16 lines
arch/arm/dts/Makefile | 1 + arch/arm/dts/meson-sm1-odroid-c4.dts | 399 +++++++++++++++++++++++++++ board/amlogic/odroid-c4/MAINTAINERS | 6 + board/amlogic/odroid-c4/Makefile | 3 + board/amlogic/odroid-c4/README | 83 ++++++ board/amlogic/odroid-c4/odroid-c4.c | 17 ++ configs/odroid-c4_defconfig | 63 +++++ 7 files changed, 572 insertions(+) create mode 100644 arch/arm/dts/meson-sm1-odroid-c4.dts create mode 100644 board/amlogic/odroid-c4/MAINTAINERS create mode 100644 board/amlogic/odroid-c4/Makefile create mode 100644 board/amlogic/odroid-c4/README create mode 100644 board/amlogic/odroid-c4/odroid-c4.c create mode 100644 configs/odroid-c4_defconfig
cover u-boot support for ODROID-C4
Quoted 9 lines · Neil Armstrong
Hi Beniamino,
Quoted 3 lines · Beniamino Galvani
Hi,
these two patches add initial u-boot support for Hardkernel ODROID-C4.
Thanks for the patchset, I already have one in my test tree, by you did beat me by sending it to the list !
Oh, I didn't notice, sorry.
Quoted 8 lines
Quoted 4 lines
https://wiki.odroid.com/odroid-c4/odroid-c4
Beniamino Galvani (2):
arm: dts: import ODROID-C4 device treeThe DT is not yet applied by kevin, thus I'll prefer waiting it to be accepted and merged in a stable linux tree to keep DT synced.
Quoted 6 lines
Quoted 1 line
boards: amlogic: add ODROID-C4 support
Please re-use the w400 board instead of adding a new board, there is no need for a new one until you'll need to add more functionalities.
I know
meson_generate_serial_ethaddr()is absent from w400, I'll add it shortly.
Okay, I'll wait that the DT gets merged and then will resubmit using w400.
Thanks,
Beniamino
cover u-boot support for ODROID-C4
In reply to Beniamino GalvaniHi Beniamino,
Quoted 11 lines · Beniamino Galvani
Hi,
these two patches add initial u-boot support for Hardkernel ODROID-C4.
https://wiki.odroid.com/odroid-c4/odroid-c4
Beniamino Galvani (2):
arm: dts: import ODROID-C4 device tree
boards: amlogic: add ODROID-C4 support
Can you respin this patches, I would like to see these get merged in the current u-boot release
-Anand
cover u-boot support for ODROID-C4
Hi,
Quoted 15 lines · Anand Moon
Hi Beniamino,
Quoted 11 lines · Beniamino Galvani
Hi,
these two patches add initial u-boot support for Hardkernel ODROID-C4.
https://wiki.odroid.com/odroid-c4/odroid-c4
Beniamino Galvani (2):
arm: dts: import ODROID-C4 device tree
boards: amlogic: add ODROID-C4 support
Quoted 5 lines
Can you respin this patches, I would like to see these get merged in the current u-boot release
-Anand
The Odroid-C4 could re-use the new Odroid-N2 board support I submitted at [1]
Anand, is the MAC address stored stored the same way on the C4 ?
Neil
[1] https://patchwork.ozlabs.org/project/uboot/patch/20200618144037.23392-1-narmstrong at baylibre.com/
cover u-boot support for ODROID-C4
Hi Neil,
Quoted 25 lines · Neil Armstrong
Hi,
Quoted 15 lines · Anand Moon
Hi Beniamino,
Quoted 11 lines · Beniamino Galvani
Hi,
these two patches add initial u-boot support for Hardkernel ODROID-C4.
https://wiki.odroid.com/odroid-c4/odroid-c4
Beniamino Galvani (2):
arm: dts: import ODROID-C4 device tree
boards: amlogic: add ODROID-C4 supportQuoted 5 lines
Can you respin this patches, I would like to see these get merged in the current u-boot release
-Anand
Quoted 7 lines
The Odroid-C4 could re-use the new Odroid-N2 board support I submitted at [1]
Anand, is the MAC address stored stored the same way on the C4 ?
Neil
[1] https://patchwork.ozlabs.org/project/uboot/patch/20200618144037.23392-1-narmstrong at baylibre.com/
I gave this patches a try on latest u-boot but I cannot make my Odroid C4 to boot up uinsg microSD card and eMMC
Here are the logs.
SM1:BL:511f6b:81ca2f;FEAT:A0F83180:20282000;POC:F;RCY:0;EMMC:800;NAND:81;SD?:0;SD:0;READ:0;0.0;CHK:0; bl2_stage_init 0x01bl2_stage_init 0x81
hw id: 0x0000 - pwm id 0x01bl2_stage_init 0xc1bl2_stage_init 0x02
no sdio debug board detected
L0:00000000
L1:00000703
L2:00008067
L3:15000020
S1:00000000
B2:20282000
B1:a0f83180
TE: 260148
BL2 Built : 22:54:32, Apr 28 2020. g12a ga659aac-dirty - changqing.gao at droid11
Board ID = 1
Set cpu clk to 24M
Set clk81 to 24M
Use GP1_pll as DSU clk.
DSU clk: 1200 Mhz
CPU clk: 1200 MHz
Set clk81 to 166.6M
DDR driver_vesion: LPDDR4_PHY_V_0_1_15 build time: Apr 28 2020 22:54:28 board id: 1
Load FIP HDR from SD, src: 0x00010200, des: 0xfffd0000, size:0x00004000, part: 0
fw parse done
Load ddrfw from SD, src: 0x00030200, des: 0xfffd0000, size: 0x0000c000, part: 0 Load ddrfw from SD, src: 0x0002c200, des: 0xfffd0000, size: 0x00004000, part: 0 PIEI prepare done
fastboot data load
fastboot data verify
verify result: 255
Cfg max: 2, cur: 1. Board id: 255. Force loop cfg
DDR4 probe
ddr clk to 1320MHz
Load ddrfw from SD, src: 0x00014200, des: 0xfffd0000, size: 0x0000c000, part: 0
dmc_version 0001
Check phy result
INFO : End of initialization
INFO : End of read enable training
INFO : End of fine write leveling
INFO : End of read dq deskew training
INFO : End of MPR read delay center optimization
INFO : End of Write leveling coarse delay
INFO : End of write delay center optimization
INFO : End of read delay center optimization
INFO : End of max read latency training
INFO : Training has run successfully!
1D training succeed
Load ddrfw from SD, src: 0x00020200, des: 0xfffd0000, size: 0x0000c000, part: 0 Check phy result
INFO : End of initialization
INFO : End of 2D read delay Voltage center optimization
INFO : End of 2D write delay Voltage center optimization
INFO : Training has run successfully!
R0_RxClkDly_Margin==106 ps 9
R0_TxDqDly_Margi==118 ps 10
R1_RxClkDly_Margin==0 ps 0
R1_TxDqDly_Margi==0 ps 0
dwc_ddrphy_apb_wr((0<<20)|(2<<16)|(0<<12)|(0xb0):0001
soc_vref_reg_value 0x 0000004e 0000004e 0000004e 0000004d 0000004f 0000004e 0000004e 0000004f 0000004c 0000004d 0000004e 0000004c 0000004c 0000004e 0000004f 0000004e 00000050 0000004e 0000004d 0000004e 0000004e 0000004c 0000004d 0000004d 0000004d 0000004f 0000004f 0000004f 0000004d 0000004d 0000004d 0000004f dram_vref_reg_value 0x 00000021
2D training succeedaml_ddr_fw_vesion: LPDDR4_PHY_V_0_1_15 build time: Jun 18 2019 20:29:43 auto size-- 65535DDR cs0 size: 2048MB
DDR cs1 size: 2048MBDMC_DDR_CTRL: 00700024DDR size: 3928MB
cs0 DataBus test pass
cs1 DataBus test pass
cs0 AddrBus test pass
cs1 AddrBus test pass
non-sec scramble use zero key
ddr scramble enabled
100bdlr_step_size ps== 461
result report
boot times 0Enable ddr reg access
Load FIP HDR from SD, src: 0x00010200, des: 0x01700000, size:0x00004000, part: 0
Load BL3X from SD, src: 0x0003c200, des: 0x0172c000, size: 0x00090000, part: 0 0.0;M3 CHK:0;cm4_sp_mode 0
MVN_1=0x00000000
MVN_2=0x00000000
[Image: g12a_v1.1.3386-3b31431 2019-05-21 10:41:54 luan.yuan at droid15-sz] OPS=0x10
ring efuse init
2b 0c 10 00 01 13 20 00 00 0f 36 30 43 57 50 50
[0.017319 Inits done]
secure task start!
high task start!
low task start!
run into bl31
NOTICE: BL31: v1.3(release):4fc40b1 NOTICE: BL31: Built : 15:57:33, May 22 2019 NOTICE: BL31: G12A normal boot! NOTICE: BL31: BL33 decompress pass ERROR: Error initializing runtime service opteed_fast
U-Boot 2020.07-rc5-00076-g46e5b60e21 (Jun 30 2020 - 21:08:25 +0530) odroid-c4
Model: Hardkernel ODROID-C4 SoC: Amlogic Meson SM1 (Unknown) Revision 2b:c (10:2) DRAM: 3.8 GiB MMC: sd at ffe05000: 0, mmc at ffe07000: 1 stdio_add_devices: Video device failed (ret=-22) In: serial at 3000 Out: serial at 3000 Err: serial at 3000 Net: Could not get PHY for ethernet@ff3f0000: addr 8
No ethernet found.
Hit any key to stop autoboot: 0
-Anand
cover u-boot support for ODROID-C4
Hi,
Quoted 32 lines · Anand Moon
Hi Neil,
Quoted 29 lines · Neil Armstrong
Hi,
Quoted 15 lines · Anand Moon
Hi Beniamino,
Quoted 11 lines · Beniamino Galvani
Hi,
these two patches add initial u-boot support for Hardkernel ODROID-C4.
https://wiki.odroid.com/odroid-c4/odroid-c4
Beniamino Galvani (2):
arm: dts: import ODROID-C4 device tree
boards: amlogic: add ODROID-C4 supportQuoted 5 lines
Can you respin this patches, I would like to see these get merged in the current u-boot release
-Anand
The Odroid-C4 could re-use the new Odroid-N2 board support I submitted at [1]
Anand, is the MAC address stored stored the same way on the C4 ?
Quoted 7 lines
Quoted 3 lines
Neil
[1] https://patchwork.ozlabs.org/project/uboot/patch/20200618144037.23392-1-narmstrong at baylibre.com/
I gave this patches a try on latest u-boot but I cannot make my Odroid C4 to boot up uinsg microSD card and eMMC
Here are the logs.
The PHY config must be wrong and it misses the -u-boot.dtsi to enable HDMI.
Can you test my custodian test branch with my C4 support patchset ?
https://gitlab.denx.de/u-boot/custodians/u-boot-amlogic/-/tree/u-boot-amlogic-test
This one is used in Armbian 5.4 release and our KernelCI lab.
Neil
Quoted 134 lines
SM1:BL:511f6b:81ca2f;FEAT:A0F83180:20282000;POC:F;RCY:0;EMMC:800;NAND:81;SD?:0;SD:0;READ:0;0.0;CHK:0;
bl2_stage_init0x01bl2_stage_init0x81
hw id:0x0000- pwm id0x01bl2_stage_init0xc1bl2_stage_init0x02no sdio debug board detected
L0:00000000
L1:00000703
L2:00008067
L3:15000020
S1:00000000
B2:20282000
B1:a0f83180TE: 260148
BL2 Built : 22:54:32, Apr 28 2020. g12a ga659aac-dirty - changqing.gao at droid11
Board ID = 1
Set cpu clk to 24M
Set clk81 to 24M
UseGP1_pllas DSU clk.
DSU clk: 1200 Mhz
CPU clk: 1200 MHz
Set clk81 to 166.6M
DDRdriver_vesion:LPDDR4_PHY_V_0_1_15build time: Apr 28 2020 22:54:28 board id: 1
Load FIP HDR from SD, src:0x00010200, des:0xfffd0000, size:0x00004000, part: 0
fw parse done
Load ddrfw from SD, src:0x00030200, des:0xfffd0000, size:0x0000c000, part: 0 Load ddrfw from SD, src:0x0002c200, des:0xfffd0000, size:0x00004000, part: 0 PIEI prepare done
fastboot data load
fastboot data verify
verify result: 255
Cfg max: 2, cur: 1. Board id: 255. Force loop cfg
DDR4 probe
ddr clk to 1320MHz
Load ddrfw from SD, src:0x00014200, des:0xfffd0000, size:0x0000c000, part: 0
dmc_version0001
Check phy result
INFO : End of initialization
INFO : End of read enable training
INFO : End of fine write leveling
INFO : End of read dq deskew training
INFO : End of MPR read delay center optimization
INFO : End of Write leveling coarse delay
INFO : End of write delay center optimization
INFO : End of read delay center optimization
INFO : End of max read latency training
INFO : Training has run successfully!
1D training succeed
Load ddrfw from SD, src:0x00020200, des:0xfffd0000, size:0x0000c000, part: 0 Check phy result
INFO : End of initialization
INFO : End of 2D read delay Voltage center optimization
INFO : End of 2D write delay Voltage center optimization
INFO : Training has run successfully!R0_RxClkDly_Margin==106 ps 9
R0_TxDqDly_Margi==118 ps 10R1_RxClkDly_Margin==0 ps 0
R1_TxDqDly_Margi==0 ps 0dwc_ddrphy_apb_wr((0<<20)|(2<<16)|(0<<12)|(0xb0):0001
soc_vref_reg_value0x0000004e0000004e0000004e0000004d0000004f0000004e0000004e0000004f0000004c0000004d0000004e0000004c0000004c0000004e0000004f0000004e000000500000004e0000004d0000004e0000004e0000004c0000004d0000004d0000004d0000004f0000004f0000004f0000004d0000004d0000004d0000004fdram_vref_reg_value0x 00000021
2D training succeedaml_ddr_fw_vesion:LPDDR4_PHY_V_0_1_15build time: Jun 18 2019 20:29:43 auto size-- 65535DDR cs0 size: 2048MB
DDR cs1 size: 2048MBDMC_DDR_CTRL: 00700024DDR size: 3928MB
cs0 DataBus test pass
cs1 DataBus test pass
cs0 AddrBus test pass
cs1 AddrBus test passnon-sec scramble use zero key
ddr scramble enabled100bdlr_step_size ps== 461
result report
boot times 0Enable ddr reg access
Load FIP HDR from SD, src:0x00010200, des:0x01700000, size:0x00004000, part: 0
Load BL3X from SD, src:0x0003c200, des:0x0172c000, size:0x00090000, part: 0 0.0;M3 CHK:0;cm4_sp_mode 0
MVN_1=0x00000000
MVN_2=0x00000000
[Image: g12a_v1.1.3386-3b31431 2019-05-21 10:41:54 luan.yuan at droid15-sz] OPS=0x10
ring efuse init
2b 0c 10 00 01 13 20 00 00 0f 36 30 43 57 50 50
[0.017319 Inits done]
secure task start!
high task start!
low task start!
run into bl31NOTICE: BL31: v1.3(release):4fc40b1 NOTICE: BL31: Built : 15:57:33, May 22 2019 NOTICE: BL31: G12A normal boot! NOTICE: BL31: BL33 decompress pass ERROR: Error initializing runtime service opteed_fastU-Boot 2020.07-rc5-00076-g46e5b60e21 (Jun 30 2020 - 21:08:25 +0530) odroid-c4
Model: Hardkernel ODROID-C4 SoC: Amlogic Meson SM1 (Unknown) Revision 2b:c (10:2) DRAM: 3.8 GiB MMC: sd at ffe05000: 0, mmc at ffe07000: 1 stdio_add_devices: Video device failed (ret=-22) In: serial at 3000 Out: serial at 3000 Err: serial at 3000 Net: Could not get PHY for ethernet at ff3f0000: addr 8No ethernet found.
Hit any key to stop autoboot: 0
-Anand
cover u-boot support for ODROID-C4
Hi Neil,
Quoted 46 lines · Neil Armstrong
Hi,
Quoted 32 lines · Anand Moon
Hi Neil,
Quoted 29 lines · Neil Armstrong
Hi,
Quoted 15 lines · Anand Moon
Hi Beniamino,
Quoted 11 lines · Beniamino Galvani
Hi,
these two patches add initial u-boot support for Hardkernel ODROID-C4.
https://wiki.odroid.com/odroid-c4/odroid-c4
Beniamino Galvani (2):
arm: dts: import ODROID-C4 device tree
boards: amlogic: add ODROID-C4 supportQuoted 5 lines
Can you respin this patches, I would like to see these get merged in the current u-boot release
-Anand
The Odroid-C4 could re-use the new Odroid-N2 board support I submitted at [1]
Anand, is the MAC address stored stored the same way on the C4 ?
Quoted 7 lines
Quoted 3 lines
Neil
[1] https://patchwork.ozlabs.org/project/uboot/patch/20200618144037.23392-1-narmstrong at baylibre.com/
I gave this patches a try on latest u-boot but I cannot make my Odroid C4 to boot up uinsg microSD card and eMMC
Here are the logs.The PHY config must be wrong and it misses the
-u-boot.dtsito enable HDMI.
Quoted 8 lines
Can you test my custodian test branch with my C4 support patchset ?
https://gitlab.denx.de/u-boot/custodians/u-boot-amlogic/-/tree/u-boot-amlogic-test
This one is used in Armbian 5.4 release and our KernelCI lab.
Neil
Thanks.
There seems to be a typo in the build instructions in # doc/board/amlogic/odroid-c4.rst
instead of *g12b*, it should be *g12a*
See below I get following build warning, which I fix locally,
./buildc4c.sh: line 78:/home/amoon/mainline/u-boot/amlogic/w400/odroid-c4/fip/g12b/aml_encrypt_g12a:
No such file or directory
./buildc4c.sh: line 81:/home/amoon/mainline/u-boot/amlogic/w400/odroid-c4/fip/g12b/aml_encrypt_g12a:
No such file or directory
./buildc4c.sh: line 84:/home/amoon/mainline/u-boot/amlogic/w400/odroid-c4/fip/g12b/aml_encrypt_g12a:
No such file or directory
./buildc4c.sh: line 87:/home/amoon/mainline/u-boot/amlogic/w400/odroid-c4/fip/g12b/aml_encrypt_g12a:
No such file or directory
./buildc4c.sh: line 90:/home/amoon/mainline/u-boot/amlogic/w400/odroid-c4/fip/g12b/aml_encrypt_g12a:
No such file or directory
./buildc4c.sh: line 92:/home/amoon/mainline/u-boot/amlogic/w400/odroid-c4/fip/g12b/aml_encrypt_g12a:
No such file or directory
After that fix I am able to boot my board using eMMC and microSD card.
-Anand
cover u-boot support for ODROID-C4
Hi,
Quoted 85 lines · Anand Moon
Hi Neil,
Quoted 46 lines · Neil Armstrong
Hi,
Quoted 32 lines · Anand Moon
Hi Neil,
Quoted 29 lines · Neil Armstrong
Hi,
Quoted 15 lines · Anand Moon
Hi Beniamino,
Quoted 11 lines · Beniamino Galvani
Hi,
these two patches add initial u-boot support for Hardkernel ODROID-C4.
https://wiki.odroid.com/odroid-c4/odroid-c4
Beniamino Galvani (2):
arm: dts: import ODROID-C4 device tree
boards: amlogic: add ODROID-C4 supportQuoted 5 lines
Can you respin this patches, I would like to see these get merged in the current u-boot release
-Anand
The Odroid-C4 could re-use the new Odroid-N2 board support I submitted at [1]
Anand, is the MAC address stored stored the same way on the C4 ?
Quoted 7 lines
Quoted 3 lines
Neil
[1] https://patchwork.ozlabs.org/project/uboot/patch/20200618144037.23392-1-narmstrong at baylibre.com/
I gave this patches a try on latest u-boot but I cannot make my Odroid C4 to boot up uinsg microSD card and eMMC
Here are the logs.The PHY config must be wrong and it misses the
-u-boot.dtsito enable HDMI.Quoted 8 lines
Can you test my custodian test branch with my C4 support patchset ?
https://gitlab.denx.de/u-boot/custodians/u-boot-amlogic/-/tree/u-boot-amlogic-test
This one is used in Armbian 5.4 release and our KernelCI lab.
Neil
Thanks.
There seems to be a typo in the build instructions in #
doc/board/amlogic/odroid-c4.rst
instead of *g12b*, it should be *g12a*See below I get following build warning, which I fix locally,
./buildc4c.sh: line 78:
/home/amoon/mainline/u-boot/amlogic/w400/odroid-c4/fip/g12b/aml_encrypt_g12a:
No such file or directory
./buildc4c.sh: line 81:/home/amoon/mainline/u-boot/amlogic/w400/odroid-c4/fip/g12b/aml_encrypt_g12a:
No such file or directory
./buildc4c.sh: line 84:/home/amoon/mainline/u-boot/amlogic/w400/odroid-c4/fip/g12b/aml_encrypt_g12a:
No such file or directory
./buildc4c.sh: line 87:/home/amoon/mainline/u-boot/amlogic/w400/odroid-c4/fip/g12b/aml_encrypt_g12a:
No such file or directory
./buildc4c.sh: line 90:/home/amoon/mainline/u-boot/amlogic/w400/odroid-c4/fip/g12b/aml_encrypt_g12a:
No such file or directory
./buildc4c.sh: line 92:/home/amoon/mainline/u-boot/amlogic/w400/odroid-c4/fip/g12b/aml_encrypt_g12a:
No such file or directory
Quoted 1 line
After that fix I am able to boot my board using eMMC and microSD card.
Thanks for testing, I'll push my serie rebased on v5.8-rc1 and fix this typo.
Neil
Quoted 3 lines
-Anand
cover u-boot support for ODROID-C4
Hi Neil,
Quoted 89 lines · Neil Armstrong
Hi,
Quoted 85 lines · Anand Moon
Hi Neil,
Quoted 46 lines · Neil Armstrong
Hi,
Quoted 32 lines · Anand Moon
Hi Neil,
Quoted 29 lines · Neil Armstrong
Hi,
Quoted 15 lines · Anand Moon
Hi Beniamino,
Quoted 11 lines · Beniamino Galvani
Hi,
these two patches add initial u-boot support for Hardkernel ODROID-C4.
https://wiki.odroid.com/odroid-c4/odroid-c4
Beniamino Galvani (2):
arm: dts: import ODROID-C4 device tree
boards: amlogic: add ODROID-C4 supportQuoted 5 lines
Can you respin this patches, I would like to see these get merged in the current u-boot release
-Anand
The Odroid-C4 could re-use the new Odroid-N2 board support I submitted at [1]
Anand, is the MAC address stored stored the same way on the C4 ?
Quoted 7 lines
Quoted 3 lines
Neil
[1] https://patchwork.ozlabs.org/project/uboot/patch/20200618144037.23392-1-narmstrong at baylibre.com/
I gave this patches a try on latest u-boot but I cannot make my Odroid C4 to boot up uinsg microSD card and eMMC
Here are the logs.The PHY config must be wrong and it misses the
-u-boot.dtsito enable HDMI.Quoted 8 lines
Can you test my custodian test branch with my C4 support patchset ?
https://gitlab.denx.de/u-boot/custodians/u-boot-amlogic/-/tree/u-boot-amlogic-test
This one is used in Armbian 5.4 release and our KernelCI lab.
Neil
Thanks.
There seems to be a typo in the build instructions in #
doc/board/amlogic/odroid-c4.rst
instead of *g12b*, it should be *g12a*See below I get following build warning, which I fix locally,
./buildc4c.sh: line 78:
/home/amoon/mainline/u-boot/amlogic/w400/odroid-c4/fip/g12b/aml_encrypt_g12a:
No such file or directory
./buildc4c.sh: line 81:/home/amoon/mainline/u-boot/amlogic/w400/odroid-c4/fip/g12b/aml_encrypt_g12a:
No such file or directory
./buildc4c.sh: line 84:/home/amoon/mainline/u-boot/amlogic/w400/odroid-c4/fip/g12b/aml_encrypt_g12a:
No such file or directory
./buildc4c.sh: line 87:/home/amoon/mainline/u-boot/amlogic/w400/odroid-c4/fip/g12b/aml_encrypt_g12a:
No such file or directory
./buildc4c.sh: line 90:/home/amoon/mainline/u-boot/amlogic/w400/odroid-c4/fip/g12b/aml_encrypt_g12a:
No such file or directory
./buildc4c.sh: line 92:/home/amoon/mainline/u-boot/amlogic/w400/odroid-c4/fip/g12b/aml_encrypt_g12a:
No such file or directory
Quoted 6 lines
Quoted 1 line
After that fix I am able to boot my board using eMMC and microSD card.
Thanks for testing, I'll push my serie rebased on v5.8-rc1 and fix this typo.
Neil
Thanks, I see the same issue with random mac address just like N2.
-Anand
cover u-boot support for ODROID-C4
Quoted 92 lines · Anand Moon
Hi Neil,
Quoted 89 lines · Neil Armstrong
Hi,
Quoted 85 lines · Anand Moon
Hi Neil,
Quoted 46 lines · Neil Armstrong
Hi,
Quoted 32 lines · Anand Moon
Hi Neil,
Quoted 29 lines · Neil Armstrong
Hi,
Quoted 15 lines · Anand Moon
Hi Beniamino,
Quoted 11 lines · Beniamino Galvani
Hi,
these two patches add initial u-boot support for Hardkernel ODROID-C4.
https://wiki.odroid.com/odroid-c4/odroid-c4
Beniamino Galvani (2):
arm: dts: import ODROID-C4 device tree
boards: amlogic: add ODROID-C4 supportQuoted 5 lines
Can you respin this patches, I would like to see these get merged in the current u-boot release
-Anand
The Odroid-C4 could re-use the new Odroid-N2 board support I submitted at [1]
Anand, is the MAC address stored stored the same way on the C4 ?
Quoted 7 lines
Quoted 3 lines
Neil
[1] https://patchwork.ozlabs.org/project/uboot/patch/20200618144037.23392-1-narmstrong at baylibre.com/
I gave this patches a try on latest u-boot but I cannot make my Odroid C4 to boot up uinsg microSD card and eMMC
Here are the logs.The PHY config must be wrong and it misses the
-u-boot.dtsito enable HDMI.Quoted 8 lines
Can you test my custodian test branch with my C4 support patchset ?
https://gitlab.denx.de/u-boot/custodians/u-boot-amlogic/-/tree/u-boot-amlogic-test
This one is used in Armbian 5.4 release and our KernelCI lab.
Neil
Thanks.
There seems to be a typo in the build instructions in #
doc/board/amlogic/odroid-c4.rst
instead of *g12b*, it should be *g12a*See below I get following build warning, which I fix locally,
./buildc4c.sh: line 78:
/home/amoon/mainline/u-boot/amlogic/w400/odroid-c4/fip/g12b/aml_encrypt_g12a:
No such file or directory
./buildc4c.sh: line 81:/home/amoon/mainline/u-boot/amlogic/w400/odroid-c4/fip/g12b/aml_encrypt_g12a:
No such file or directory
./buildc4c.sh: line 84:/home/amoon/mainline/u-boot/amlogic/w400/odroid-c4/fip/g12b/aml_encrypt_g12a:
No such file or directory
./buildc4c.sh: line 87:/home/amoon/mainline/u-boot/amlogic/w400/odroid-c4/fip/g12b/aml_encrypt_g12a:
No such file or directory
./buildc4c.sh: line 90:/home/amoon/mainline/u-boot/amlogic/w400/odroid-c4/fip/g12b/aml_encrypt_g12a:
No such file or directory
./buildc4c.sh: line 92:/home/amoon/mainline/u-boot/amlogic/w400/odroid-c4/fip/g12b/aml_encrypt_g12a:
No such file or directory
Quoted 8 lines
Quoted 6 lines
Quoted 1 line
After that fix I am able to boot my board using eMMC and microSD card.
Thanks for testing, I'll push my serie rebased on v5.8-rc1 and fix this typo.
Neil
Thanks, I see the same issue with random mac address just like N2.
Yes, my branch was not using the N2 board support with eFuses MAC readout, can you test my last patchset I just sent ? It should use the MAC from eFuses or generate an unique address with the SoC serial number.
Please apply the patch in [1] before the new Odroid-C4 serie.
[1] https://patchwork.ozlabs.org/project/uboot/patch/20200618144037.23392-1-narmstrong at baylibre.com/
Neil
Quoted 3 lines
-Anand
cover u-boot support for ODROID-C4
Hi Neil,
Quoted 98 lines · Neil Armstrong
Quoted 96 lines · Anand Moon
Hi Neil,
Quoted 93 lines · Neil Armstrong
Hi,
Quoted 85 lines · Anand Moon
Hi Neil,
Quoted 46 lines · Neil Armstrong
Hi,
Quoted 32 lines · Anand Moon
Hi Neil,
Quoted 29 lines · Neil Armstrong
Hi,
Quoted 15 lines · Anand Moon
Hi Beniamino,
Quoted 11 lines · Beniamino Galvani
Hi,
these two patches add initial u-boot support for Hardkernel ODROID-C4.
https://wiki.odroid.com/odroid-c4/odroid-c4
Beniamino Galvani (2):
arm: dts: import ODROID-C4 device tree
boards: amlogic: add ODROID-C4 supportQuoted 5 lines
Can you respin this patches, I would like to see these get merged in the current u-boot release
-Anand
The Odroid-C4 could re-use the new Odroid-N2 board support I submitted at [1]
Anand, is the MAC address stored stored the same way on the C4 ?
Quoted 7 lines
Quoted 3 lines
Neil
[1] https://patchwork.ozlabs.org/project/uboot/patch/20200618144037.23392-1-narmstrong at baylibre.com/
I gave this patches a try on latest u-boot but I cannot make my Odroid C4 to boot up uinsg microSD card and eMMC
Here are the logs.The PHY config must be wrong and it misses the
-u-boot.dtsito enable HDMI.Quoted 8 lines
Can you test my custodian test branch with my C4 support patchset ?
https://gitlab.denx.de/u-boot/custodians/u-boot-amlogic/-/tree/u-boot-amlogic-test
This one is used in Armbian 5.4 release and our KernelCI lab.
Neil
Thanks.
There seems to be a typo in the build instructions in #
doc/board/amlogic/odroid-c4.rst
instead of *g12b*, it should be *g12a*See below I get following build warning, which I fix locally,
./buildc4c.sh: line 78:
/home/amoon/mainline/u-boot/amlogic/w400/odroid-c4/fip/g12b/aml_encrypt_g12a:
No such file or directory
./buildc4c.sh: line 81:/home/amoon/mainline/u-boot/amlogic/w400/odroid-c4/fip/g12b/aml_encrypt_g12a:
No such file or directory
./buildc4c.sh: line 84:/home/amoon/mainline/u-boot/amlogic/w400/odroid-c4/fip/g12b/aml_encrypt_g12a:
No such file or directory
./buildc4c.sh: line 87:/home/amoon/mainline/u-boot/amlogic/w400/odroid-c4/fip/g12b/aml_encrypt_g12a:
No such file or directory
./buildc4c.sh: line 90:/home/amoon/mainline/u-boot/amlogic/w400/odroid-c4/fip/g12b/aml_encrypt_g12a:
No such file or directory
./buildc4c.sh: line 92:/home/amoon/mainline/u-boot/amlogic/w400/odroid-c4/fip/g12b/aml_encrypt_g12a:
No such file or directoryQuoted 1 line
After that fix I am able to boot my board using eMMC and microSD card.
Thanks for testing, I'll push my serie rebased on v5.8-rc1 and fix this typo.
Quoted 9 lines
Quoted 4 lines
Quoted 2 lines
Neil
Thanks, I see the same issue with random mac address just like N2.
Yes, my branch was not using the N2 board support with eFuses MAC readout, can you test my last patchset I just sent ? It should use the MAC from eFuses or generate an unique address with the SoC serial number.
Thanks
Quoted 5 lines
Please apply the patch in [1] before the new Odroid-C4 serie.
[1] https://patchwork.ozlabs.org/project/uboot/patch/20200618144037.23392-1-narmstrong at baylibre.com/
Neil
I do not know the reason but your patches are not showing up on u-boot patchwork.
[0] https://patchwork.ozlabs.org/project/uboot/list/
-Anand
cover u-boot support for ODROID-C4
Quoted 114 lines · Anand Moon
Hi Neil,
Quoted 98 lines · Neil Armstrong
Quoted 96 lines · Anand Moon
Hi Neil,
Quoted 93 lines · Neil Armstrong
Hi,
Quoted 85 lines · Anand Moon
Hi Neil,
Quoted 46 lines · Neil Armstrong
Hi,
Quoted 32 lines · Anand Moon
Hi Neil,
Quoted 29 lines · Neil Armstrong
Hi,
Quoted 15 lines · Anand Moon
Hi Beniamino,
Quoted 11 lines · Beniamino Galvani
Hi,
these two patches add initial u-boot support for Hardkernel ODROID-C4.
https://wiki.odroid.com/odroid-c4/odroid-c4
Beniamino Galvani (2):
arm: dts: import ODROID-C4 device tree
boards: amlogic: add ODROID-C4 supportQuoted 5 lines
Can you respin this patches, I would like to see these get merged in the current u-boot release
-Anand
The Odroid-C4 could re-use the new Odroid-N2 board support I submitted at [1]
Anand, is the MAC address stored stored the same way on the C4 ?
Quoted 7 lines
Quoted 3 lines
Neil
[1] https://patchwork.ozlabs.org/project/uboot/patch/20200618144037.23392-1-narmstrong at baylibre.com/
I gave this patches a try on latest u-boot but I cannot make my Odroid C4 to boot up uinsg microSD card and eMMC
Here are the logs.The PHY config must be wrong and it misses the
-u-boot.dtsito enable HDMI.Quoted 8 lines
Can you test my custodian test branch with my C4 support patchset ?
https://gitlab.denx.de/u-boot/custodians/u-boot-amlogic/-/tree/u-boot-amlogic-test
This one is used in Armbian 5.4 release and our KernelCI lab.
Neil
Thanks.
There seems to be a typo in the build instructions in #
doc/board/amlogic/odroid-c4.rst
instead of *g12b*, it should be *g12a*See below I get following build warning, which I fix locally,
./buildc4c.sh: line 78:
/home/amoon/mainline/u-boot/amlogic/w400/odroid-c4/fip/g12b/aml_encrypt_g12a:
No such file or directory
./buildc4c.sh: line 81:/home/amoon/mainline/u-boot/amlogic/w400/odroid-c4/fip/g12b/aml_encrypt_g12a:
No such file or directory
./buildc4c.sh: line 84:/home/amoon/mainline/u-boot/amlogic/w400/odroid-c4/fip/g12b/aml_encrypt_g12a:
No such file or directory
./buildc4c.sh: line 87:/home/amoon/mainline/u-boot/amlogic/w400/odroid-c4/fip/g12b/aml_encrypt_g12a:
No such file or directory
./buildc4c.sh: line 90:/home/amoon/mainline/u-boot/amlogic/w400/odroid-c4/fip/g12b/aml_encrypt_g12a:
No such file or directory
./buildc4c.sh: line 92:/home/amoon/mainline/u-boot/amlogic/w400/odroid-c4/fip/g12b/aml_encrypt_g12a:
No such file or directoryQuoted 1 line
After that fix I am able to boot my board using eMMC and microSD card.
Thanks for testing, I'll push my serie rebased on v5.8-rc1 and fix this typo.
Quoted 9 lines
Quoted 4 lines
Quoted 2 lines
Neil
Thanks, I see the same issue with random mac address just like N2.
Yes, my branch was not using the N2 board support with eFuses MAC readout, can you test my last patchset I just sent ? It should use the MAC from eFuses or generate an unique address with the SoC serial number.
Thanks
Quoted 2 lines
Please apply the patch in [1] before the new Odroid-C4 serie.
Quoted 8 lines
Quoted 3 lines
[1] https://patchwork.ozlabs.org/project/uboot/patch/20200618144037.23392-1-narmstrong at baylibre.com/
Neil
I do not know the reason but your patches are not showing up on u-boot patchwork.
Good question !
Neil
Quoted 3 lines
-Anand
cover u-boot support for ODROID-C4
Hi Neil,
Quoted 120 lines · Neil Armstrong
Quoted 118 lines · Anand Moon
Hi Neil,
Quoted 98 lines · Neil Armstrong
Quoted 96 lines · Anand Moon
Hi Neil,
Quoted 93 lines · Neil Armstrong
Hi,
Quoted 85 lines · Anand Moon
Hi Neil,
Quoted 46 lines · Neil Armstrong
Hi,
Quoted 32 lines · Anand Moon
Hi Neil,
Quoted 29 lines · Neil Armstrong
Hi,
Quoted 15 lines · Anand Moon
Hi Beniamino,
Quoted 11 lines · Beniamino Galvani
Hi,
these two patches add initial u-boot support for Hardkernel ODROID-C4.
https://wiki.odroid.com/odroid-c4/odroid-c4
Beniamino Galvani (2):
arm: dts: import ODROID-C4 device tree
boards: amlogic: add ODROID-C4 supportQuoted 5 lines
Can you respin this patches, I would like to see these get merged in the current u-boot release
-Anand
The Odroid-C4 could re-use the new Odroid-N2 board support I submitted at [1]
Anand, is the MAC address stored stored the same way on the C4 ?
Quoted 7 lines
Quoted 3 lines
Neil
[1] https://patchwork.ozlabs.org/project/uboot/patch/20200618144037.23392-1-narmstrong at baylibre.com/
I gave this patches a try on latest u-boot but I cannot make my Odroid C4 to boot up uinsg microSD card and eMMC
Here are the logs.The PHY config must be wrong and it misses the
-u-boot.dtsito enable HDMI.Quoted 8 lines
Can you test my custodian test branch with my C4 support patchset ?
https://gitlab.denx.de/u-boot/custodians/u-boot-amlogic/-/tree/u-boot-amlogic-test
This one is used in Armbian 5.4 release and our KernelCI lab.
Neil
Thanks.
There seems to be a typo in the build instructions in #
doc/board/amlogic/odroid-c4.rst
instead of *g12b*, it should be *g12a*See below I get following build warning, which I fix locally,
./buildc4c.sh: line 78:
/home/amoon/mainline/u-boot/amlogic/w400/odroid-c4/fip/g12b/aml_encrypt_g12a:
No such file or directory
./buildc4c.sh: line 81:/home/amoon/mainline/u-boot/amlogic/w400/odroid-c4/fip/g12b/aml_encrypt_g12a:
No such file or directory
./buildc4c.sh: line 84:/home/amoon/mainline/u-boot/amlogic/w400/odroid-c4/fip/g12b/aml_encrypt_g12a:
No such file or directory
./buildc4c.sh: line 87:/home/amoon/mainline/u-boot/amlogic/w400/odroid-c4/fip/g12b/aml_encrypt_g12a:
No such file or directory
./buildc4c.sh: line 90:/home/amoon/mainline/u-boot/amlogic/w400/odroid-c4/fip/g12b/aml_encrypt_g12a:
No such file or directory
./buildc4c.sh: line 92:/home/amoon/mainline/u-boot/amlogic/w400/odroid-c4/fip/g12b/aml_encrypt_g12a:
No such file or directoryQuoted 1 line
After that fix I am able to boot my board using eMMC and microSD card.
Thanks for testing, I'll push my serie rebased on v5.8-rc1 and fix this typo.
Quoted 9 lines
Quoted 4 lines
Quoted 2 lines
Neil
Thanks, I see the same issue with random mac address just like N2.
Yes, my branch was not using the N2 board support with eFuses MAC readout, can you test my last patchset I just sent ? It should use the MAC from eFuses or generate an unique address with the SoC serial number.
Thanks
Quoted 5 lines
Please apply the patch in [1] before the new Odroid-C4 serie.
[1] https://patchwork.ozlabs.org/project/uboot/patch/20200618144037.23392-1-narmstrong at baylibre.com/
Neil
Quoted 9 lines
Quoted 4 lines
I do not know the reason but your patches are not showing up on u-boot patchwork.
Good question !
Neil
Now it's showing up on u-boot patchwork.
https://patchwork.ozlabs.org/project/uboot/list/?series=187096
-Anand