clk: clk-si5341: Add support for the Si5345 series
Subsystems (2)
PATCH 1/1 clk: clk-si5341: Add support for the Si5345 series
Add support for the Si5342, Si5344 and Si5345 chips. These are equivalent to the Si5341 family, but with more clock input options (which are not supported yet by this driver).
Signed-off-by Mike Looijmans <[email protected]>
--- .../bindings/clock/silabs,si5341.txt | 11 ++- drivers/clk/clk-si5341.c | 69 +++++++++++++++++-- 2 files changed, 74 insertions(+), 6 deletions(-)
Documentation/devicetree/bindings/clock/silabs,si5341.txt +10 -1
@@ -1,15 +1,21 @@ -Binding for Silicon Labs Si5341 and Si5340 programmable i2c clock generator. +Binding for Silicon Labs Si5340, Si5341 Si5342, Si5344 and Si5345 programmable +i2c clock generator. Reference [1] Si5341 Data Sheet https://www.silabs.com/documents/public/data-sheets/Si5341-40-D-DataSheet.pdf [2] Si5341 Reference Manual https://www.silabs.com/documents/public/reference-manuals/Si5341-40-D-RM.pdf +[3] Si5345 Reference Manual + https://www.silabs.com/documents/public/reference-manuals/Si5345-44-42-D-RM.pdf The Si5341 and Si5340 are programmable i2c clock generators with up to 10 output clocks. The chip contains a PLL that sources 5 (or 4) multisynth clocks, which in turn can be directed to any of the 10 (or 4) outputs through a divider. The internal structure of the clock generators can be found in [2]. +The Si5345 is similar to the Si5341 with the addition of fractional input +dividers and automatic input selection, as described in [3]. +The Si5342 and Si5344 are smaller versions of the Si5345, with 2 or 4 outputs. The driver can be used in "as is" mode, reading the current settings from the chip at boot, in case you have a (pre-)programmed device. If the PLL is not
@@ -28,6 +34,9 @@ Required properties: - compatible: shall be one of the following: "silabs,si5340" - Si5340 A/B/C/D "silabs,si5341" - Si5341 A/B/C/D + "silabs,si5342" - Si5342 A/B/C/D + "silabs,si5344" - Si5344 A/B/C/D + "silabs,si5345" - Si5345 A/B/C/D - reg: i2c device address, usually 0x74 - #clock-cells: from common clock binding; shall be set to 2. The first value is "0" for outputs, "1" for synthesizers.
drivers/clk/clk-si5341.c +64 -5
145 lines not on this page · raw message
Signature · 1 line
2.17.1
Quoted 10 lines · Mike Looijmans
Add support for the Si5342, Si5344 and Si5345 chips. These are equivalent to the Si5341 family, but with more clock input options (which are not supported yet by this driver).
Signed-off-by Mike Looijmans <[email protected]>--- .../bindings/clock/silabs,si5341.txt | 11 ++- drivers/clk/clk-si5341.c | 69 +++++++++++++++++-- 2 files changed, 74 insertions(+), 6 deletions(-)
Acked-by Rob Herring <[email protected]>
Quoting Mike Looijmans (2020-05-06 23:15:44)
Quoted 6 lines
Add support for the Si5342, Si5344 and Si5345 chips. These are equivalent to the Si5341 family, but with more clock input options (which are not supported yet by this driver).
Signed-off-by Mike Looijmans <[email protected]>---
Applied to clk-next