Add Rockchip RK3399 USB3.0 Host support
Subsystems (5)
v3 cover Add Rockchip RK3399 USB3.0 Host support
This series add quirks for DWC3 and add Rockchip RK3399 USB3.0 host support.
Tested on top of Jagan 'rockchip: PHY drivers (USB)' series [1].
For V3 update:
- Fix compile error for [PATCH v2 1/9].
- Use Jagan's Type-C driver instead of [PATCH v2 5/9].
- Cleanup dts changes for [PATCH v2 7/9].
- Cleanup config changes for [PATCH v2 8/9] and [PATCH v2 9/9].
For V2 update:
- Amend type-c driver followed Jagan's comments for [PATCH 5/8].
- Fix dts commit for [PATCH 7/8].
- Split RK3399 default config for [PATCH 8/8].
- Add 'Reviewed-by' tag for [PATCH 1/8], [PATCH 2/8] and [PATCH 3/8].
[1] https://patchwork.ozlabs.org/project/uboot/cover/20200506075025.1677-1-jagan at amarulasolutions.com
BR,
Frank
Frank Wang (7):
usb: dwc3: add dis_enblslpm_quirk
usb: dwc3: add dis_u2_freeclk_exists_quirk
usb: dwc3: amend UTMI/UTMIW phy interface setup
usb: dwc3: add make compatible for rockchip platform
driver: usb: drop legacy rockchip xhci driver
ARM: dts: rk3399-evb: usb3.0 host support
configs: evb-rk3399: update support usb3.0 host
arch/arm/dts/rk3399-evb.dts | 13 ++ configs/evb-rk3399_defconfig | 6 + drivers/usb/common/common.c | 25 ++++ drivers/usb/dwc3/core.c | 77 +++++++----- drivers/usb/dwc3/core.h | 9 ++ drivers/usb/dwc3/dwc3-generic.c | 33 +++++- drivers/usb/host/Kconfig | 9 -- drivers/usb/host/Makefile | 1 - drivers/usb/host/xhci-rockchip.c | 196 ------------------------------- include/dwc3-uboot.h | 2 + include/linux/usb/phy.h | 18 +++ 11 files changed, 146 insertions(+), 243 deletions(-) delete mode 100644 drivers/usb/host/xhci-rockchip.c
Signature · 1 line
2.17.1
PATCH v3 1/7 usb: dwc3: add dis_enblslpm_quirk
Add a quirk to clear the GUSB2PHYCFG.ENBLSLPM bit, which controls whether the PHY receives the suspend signal from the controller.
Refer to commit ec791d149bca("usb: dwc3: Add dis_enblslpm_quirk") in Linux Kernel.
---
Changes for v3:
- Fix compile error for 'DWC3_GUSB2PHYCFG_ENBLSLPM' macro.
drivers/usb/dwc3/core.c | 6 ++++++ drivers/usb/dwc3/core.h | 2 ++ include/dwc3-uboot.h | 1 + 3 files changed, 9 insertions(+)
drivers/usb/dwc3/core.c +6 -0
@@ -398,6 +398,9 @@ static void dwc3_phy_setup(struct dwc3 *dwc)if (dwc->dis_u2_susphy_quirk) reg &= ~DWC3_GUSB2PHYCFG_SUSPHY ; +if (dwc->dis_enblslpm_quirk) + reg &= ~DWC3_GUSB2PHYCFG_ENBLSLPM ; +dwc3_writel (dwc->regs,DWC3_GUSB2PHYCFG (0 ), reg);mdelay (100 );
@@ -719,6 +722,7 @@ int dwc3_uboot_init(struct dwc3_device *dwc3_dev) dwc->dis_u3_susphy_quirk = dwc3_dev->dis_u3_susphy_quirk; dwc->dis_u2_susphy_quirk = dwc3_dev->dis_u2_susphy_quirk; dwc->dis_del_phy_power_chg_quirk = dwc3_dev->dis_del_phy_power_chg_quirk; + dwc->dis_enblslpm_quirk = dwc3_dev->dis_enblslpm_quirk; dwc->tx_de_emphasis_quirk = dwc3_dev->tx_de_emphasis_quirk;if (dwc3_dev->tx_de_emphasis)
@@ -981,6 +985,8 @@ void dwc3_of_parse(struct dwc3 *dwc) "snps,dis_u2_susphy_quirk"); dwc->dis_del_phy_power_chg_quirk =dev_read_bool (dev,"snps,dis-del-phy-power-chg-quirk" ); + dwc->dis_enblslpm_quirk =dev_read_bool (dev, +"snps,dis_enblslpm_quirk" ); dwc->tx_de_emphasis_quirk =dev_read_bool (dev,"snps,tx_de_emphasis_quirk" ); tmp =dev_read_u8_array_ptr (dev,"snps,tx_de_emphasis" ,1 );
drivers/usb/dwc3/core.h +2 -0
@@ -162,6 +162,7 @@/* Global USB2 PHY Configuration Register */ #define DWC3_GUSB2PHYCFG_PHYSOFTRST (1 << 31)#define DWC3_GUSB2PHYCFG_SUSPHY (1 << 6) +#define DWC3_GUSB2PHYCFG_ENBLSLPM (1 << 8)#define DWC3_GUSB2PHYCFG_PHYIF (n) ((n) << 3)#define DWC3_GUSB2PHYCFG_PHYIF_MASK DWC3_GUSB2PHYCFG_PHYIF(1)#define DWC3_GUSB2PHYCFG_USBTRDTIM (n) ((n) << 10)
@@ -822,6 +823,7 @@ struct dwc3 { unsigned dis_u3_susphy_quirk:1; unsigned dis_u2_susphy_quirk:1; unsigned dis_del_phy_power_chg_quirk:1; + unsigned dis_enblslpm_quirk:1; unsigned tx_de_emphasis_quirk:1; unsigned tx_de_emphasis:2;
include/dwc3-uboot.h +1 -0
@@ -33,6 +33,7 @@ struct dwc3_device {unsigned dis_u3_susphy_quirk;unsigned dis_u2_susphy_quirk;unsigned dis_del_phy_power_chg_quirk; +unsigned dis_enblslpm_quirk;unsigned tx_de_emphasis_quirk;unsigned tx_de_emphasis;int index;
Signature · 1 line
2.17.1
PATCH v3 1/7 usb: dwc3: add dis_enblslpm_quirk
Quoted 10 lines · Frank Wang
Add a quirk to clear the GUSB2PHYCFG.ENBLSLPM bit, which controls whether the PHY receives the suspend signal from the controller.
Refer to commit
ec791d149bca("usb: dwc3: Add dis_enblslpm_quirk")in Linux Kernel.Signed-off-by Frank Wang <[email protected]>Reviewed-by Kever Yang <[email protected]>---
PATCH v3 2/7 usb: dwc3: add dis_u2_freeclk_exists_quirk
In reply to Frank WangAdd a quirk to clear the GUSB2PHYCFG.U2_FREECLK_EXISTS bit, which specifies whether the USB2.0 PHY provides a free-running PHY clock, which is active when the clock control input is active.
Refer to commit 27f83eeb6b42("usb: dwc3: add dis_u2_freeclk_exists_quirk") in Linux Rockchip Kernel.
---
Changes for v3:
- none
drivers/usb/dwc3/core.c | 6 ++++++ drivers/usb/dwc3/core.h | 2 ++ include/dwc3-uboot.h | 1 + 3 files changed, 9 insertions(+)
drivers/usb/dwc3/core.c +6 -0
@@ -401,6 +401,9 @@ static void dwc3_phy_setup(struct dwc3 *dwc)if (dwc->dis_enblslpm_quirk) reg &= ~DWC3_GUSB2PHYCFG_ENBLSLPM ; +if (dwc->dis_u2_freeclk_exists_quirk) + reg &= ~DWC3_GUSB2PHYCFG_U2_FREECLK_EXISTS ; +dwc3_writel (dwc->regs,DWC3_GUSB2PHYCFG (0 ), reg);mdelay (100 );
@@ -723,6 +726,7 @@ int dwc3_uboot_init(struct dwc3_device *dwc3_dev) dwc->dis_u2_susphy_quirk = dwc3_dev->dis_u2_susphy_quirk; dwc->dis_del_phy_power_chg_quirk = dwc3_dev->dis_del_phy_power_chg_quirk; dwc->dis_enblslpm_quirk = dwc3_dev->dis_enblslpm_quirk; + dwc->dis_u2_freeclk_exists_quirk = dwc3_dev->dis_u2_freeclk_exists_quirk; dwc->tx_de_emphasis_quirk = dwc3_dev->tx_de_emphasis_quirk;if (dwc3_dev->tx_de_emphasis)
@@ -987,6 +991,8 @@ void dwc3_of_parse(struct dwc3 *dwc) "snps,dis-del-phy-power-chg-quirk"); dwc->dis_enblslpm_quirk =dev_read_bool (dev,"snps,dis_enblslpm_quirk" ); + dwc->dis_u2_freeclk_exists_quirk =dev_read_bool (dev, +"snps,dis-u2-freeclk-exists-quirk" ); dwc->tx_de_emphasis_quirk =dev_read_bool (dev,"snps,tx_de_emphasis_quirk" ); tmp =dev_read_u8_array_ptr (dev,"snps,tx_de_emphasis" ,1 );
drivers/usb/dwc3/core.h +2 -0
@@ -161,6 +161,7 @@/* Global USB2 PHY Configuration Register */ #define DWC3_GUSB2PHYCFG_PHYSOFTRST (1 << 31) +#define DWC3_GUSB2PHYCFG_U2_FREECLK_EXISTS (1 << 30)#define DWC3_GUSB2PHYCFG_SUSPHY (1 << 6)#define DWC3_GUSB2PHYCFG_ENBLSLPM (1 << 8)#define DWC3_GUSB2PHYCFG_PHYIF (n) ((n) << 3)
@@ -824,6 +825,7 @@ struct dwc3 { unsigned dis_u2_susphy_quirk:1; unsigned dis_del_phy_power_chg_quirk:1; unsigned dis_enblslpm_quirk:1; + unsigned dis_u2_freeclk_exists_quirk:1; unsigned tx_de_emphasis_quirk:1; unsigned tx_de_emphasis:2;
include/dwc3-uboot.h +1 -0
@@ -34,6 +34,7 @@ struct dwc3_device {unsigned dis_u2_susphy_quirk;unsigned dis_del_phy_power_chg_quirk;unsigned dis_enblslpm_quirk; +unsigned dis_u2_freeclk_exists_quirk;unsigned tx_de_emphasis_quirk;unsigned tx_de_emphasis;int index;
Signature · 1 line
2.17.1
PATCH v3 2/7 usb: dwc3: add dis_u2_freeclk_exists_quirk
Quoted 11 lines · Frank Wang
Add a quirk to clear the GUSB2PHYCFG.U2_FREECLK_EXISTS bit, which specifies whether the USB2.0 PHY provides a free-running PHY clock, which is active when the clock control input is active.
Refer to commit 27f83eeb6b42("usb: dwc3: add
dis_u2_freeclk_exists_quirk") in Linux Rockchip Kernel.Signed-off-by Frank Wang <[email protected]>Reviewed-by Kever Yang <[email protected]>---
PATCH v3 3/7 usb: dwc3: amend UTMI/UTMIW phy interface setup
In reply to Frank WangLet move 8/16-bit UTMI+ interface initialization into DWC3 core init that is convenient for both DM_USB and u-boot traditional process.
---
Changes for v3:
- none
drivers/usb/common/common.c | 25 ++++++++++++++ drivers/usb/dwc3/core.c | 65 +++++++++++++++++++------------------ drivers/usb/dwc3/core.h | 5 +++ include/linux/usb/phy.h | 18 ++++++++++ 4 files changed, 82 insertions(+), 31 deletions(-)
drivers/usb/common/common.c +25 -0
@@ -10,6 +10,7 @@#include <dm.h> #include <linux/usb/otg.h> #include <linux/usb/ch9.h> +#include <linux/usb/phy.h> DECLARE_GLOBAL_DATA_PTR ;
@@ -64,3 +65,27 @@ enum usb_device_speed usb_get_maximum_speed(ofnode node)return USB_SPEED_UNKNOWN ; } + +#if CONFIG_IS_ENABLED (OF_LIVE ) &&CONFIG_IS_ENABLED (DM_USB ) +static const char *const usbphy_modes[] = { + [USBPHY_INTERFACE_MODE_UNKNOWN ] ="" , + [USBPHY_INTERFACE_MODE_UTMI ] ="utmi" , + [USBPHY_INTERFACE_MODE_UTMIW ] ="utmi_wide" , +}; + +enum usb_phy_interface usb_get_phy_mode (ofnode node) +{ +const char *phy_type; +int i; + + phy_type =ofnode_get_property (node,"phy_type" ,NULL ); +if (!phy_type) +return USBPHY_INTERFACE_MODE_UNKNOWN ; + +for (i =0 ; i <ARRAY_SIZE (usbphy_modes); i++) +if (!strcmp (phy_type, usbphy_modes[i])) +return i; + +return USBPHY_INTERFACE_MODE_UNKNOWN ; +} +#endif
drivers/usb/dwc3/core.c +34 -31
101 lines not on this page · raw message
drivers/usb/dwc3/core.h +5 -0
@@ -21,6 +21,7 @@#include <linux/usb/ch9.h> #include <linux/usb/otg.h> +#include <linux/usb/phy.h> #define DWC3_MSG_MAX 500
@@ -650,6 +651,9 @@ struct dwc3_scratchpad_array {* @maximum_speed: maximum speed requested (mainly for testing purposes) * @revision: revision register contents * @dr_mode: requested mode of operation +* @hsphy_mode: UTMI phy mode, one of following: +* - USBPHY_INTERFACE_MODE_UTMI +* - USBPHY_INTERFACE_MODE_UTMIW * @dcfg: saved contents of DCFG register * @gctl: saved contents of GCTL register * @isoch_delay: wValue from Set Isochronous Delay request;
@@ -741,6 +745,7 @@ struct dwc3 {size_t regs_size;enum usb_dr_mode dr_mode; +enum usb_phy_interface hsphy_mode;/* used for suspend/resume */ u32 dcfg;
include/linux/usb/phy.h +18 -0
@@ -10,10 +10,28 @@#ifndef __LINUX_USB_PHY_H#define __LINUX_USB_PHY_H +#include <dm/ofnode.h> +enum usb_phy_interface {USBPHY_INTERFACE_MODE_UNKNOWN ,USBPHY_INTERFACE_MODE_UTMI ,USBPHY_INTERFACE_MODE_UTMIW , }; +#if CONFIG_IS_ENABLED (OF_LIVE ) &&CONFIG_IS_ENABLED (DM_USB ) +/** +* usb_get_phy_mode - Get phy mode for given device_node +* @np: Pointer to the given device_node +* +* The function gets phy interface string from property 'phy_type', +* and returns the corresponding enum usb_phy_interface +*/ +enum usb_phy_interface usb_get_phy_mode (ofnode node); +#else +static inline enum usb_phy_interface usb_get_phy_mode (ofnode node) +{ +return USBPHY_INTERFACE_MODE_UNKNOWN ; +} +#endif +#endif /* __LINUX_USB_PHY_H */
Signature · 1 line
2.17.1
PATCH v3 4/7 usb: dwc3: add make compatible for rockchip platform
In reply to Frank WangRK3399 Type-C PHY is required that must hold whole USB3.0 OTG controller in resetting to hold pipe power state in P2 before initializing the PHY. This commit fixed it and added device compatible for rockchip platform.
---
Changes for v3:
- none
drivers/usb/dwc3/dwc3-generic.c | 33 +++++++++++++++++++++++++++------ 1 file changed, 27 insertions(+), 6 deletions(-)
drivers/usb/dwc3/dwc3-generic.c +27 -6
@@ -24,6 +24,12 @@#include <clk.h> #include <usb/xhci.h> +struct dwc3_glue_data { +struct clk_bulk clks; +struct reset_ctl_bulk resets; +fdt_addr_t regs; +}; +struct dwc3_generic_plat {fdt_addr_t base;u32 maximum_speed;
@@ -48,6 +54,7 @@ static int dwc3_generic_probe(struct udevice *dev,int rc;struct dwc3_generic_plat *plat =dev_get_platdata (dev);struct dwc3 *dwc3 = &priv->dwc3; +struct dwc3_glue_data *glue =dev_get_platdata (dev->parent); dwc3->dev = dev; dwc3->maximum_speed = plat->maximum_speed;
@@ -56,10 +63,22 @@ static int dwc3_generic_probe(struct udevice *dev,dwc3_of_parse (dwc3);#endif +/* +* It must hold whole USB3.0 OTG controller in resetting to hold pipe +* power state in P2 before initializing TypeC PHY on RK3399 platform. +*/ +if (device_is_compatible (dev->parent,"rockchip,rk3399-dwc3" )) { +reset_assert_bulk (&glue->resets); +udelay (1 ); + } + rc =dwc3_setup_phy (dev, &priv->phys, &priv->num_phys);if (rc)return rc; +if (device_is_compatible (dev->parent,"rockchip,rk3399-dwc3" )) +reset_deassert_bulk (&glue->resets); + priv->base =map_physmem (plat->base,DWC3_OTG_REGS_END ,MAP_NOCACHE ); dwc3->regs = priv->base +DWC3_GLOBALS_REGS_START ;
@@ -187,12 +206,6 @@ U_BOOT_DRIVER(dwc3_generic_host) = { };#endif -struct dwc3_glue_data { -struct clk_bulk clks; -struct reset_ctl_bulk resets; -fdt_addr_t regs; -}; -struct dwc3_glue_ops {void (*select_dr_mode)(struct udevice *dev,int index,enum usb_dr_mode mode);
@@ -395,6 +408,12 @@ static int dwc3_glue_probe(struct udevice *dev)if (ret)return ret; +if (glue->resets.count <1 ) { + ret =dwc3_glue_reset_init (child, glue); +if (ret) +return ret; + } +while (child) {enum usb_dr_mode dr_mode;
@@ -425,6 +444,8 @@ static const struct udevice_id dwc3_glue_ids[] = { { .compatible = "ti,dwc3", .data = (ulong)&ti_ops }, { .compatible = "ti,am437x-dwc3", .data = (ulong)&ti_ops }, { .compatible = "ti,am654-dwc3" }, + { .compatible = "rockchip,rk3328-dwc3" }, + { .compatible = "rockchip,rk3399-dwc3" }, { } };
Signature · 1 line
2.17.1
PATCH v3 5/7 driver: usb: drop legacy rockchip xhci driver
In reply to Frank WangWe have changed to use dwc3 generic driver for usb3.0 host, so the legacy Rockchip's xHCI driver is not needed, and drop it.
---
Changes for v3:
- none
drivers/usb/host/Kconfig | 9 -- drivers/usb/host/Makefile | 1 - drivers/usb/host/xhci-rockchip.c | 196 ------------------------------- 3 files changed, 206 deletions(-) delete mode 100644 drivers/usb/host/xhci-rockchip.c
drivers/usb/host/Kconfig +0 -9
@@ -47,15 +47,6 @@ config USB_XHCI_PCI help Enables support for the PCI-based xHCI controller. -config USB_XHCI_ROCKCHIP - bool "Support for Rockchip on-chip xHCI USB controller" - depends on ARCH_ROCKCHIP - depends on DM_REGULATOR - depends on DM_USB - default y - help - Enables support for the on-chip xHCI controller on Rockchip SoCs. - config USB_XHCI_RCAR bool "Renesas RCar USB 3.0 support" default y
drivers/usb/host/Makefile +0 -1
@@ -48,7 +48,6 @@ obj-$(CONFIG_USB_XHCI_BRCM) += xhci-brcm.o obj-$(CONFIG_USB_XHCI_HCD) += xhci.o xhci-mem.o xhci-ring.o obj-$(CONFIG_USB_XHCI_DWC3) += xhci-dwc3.o obj-$(CONFIG_USB_XHCI_DWC3_OF_SIMPLE) += dwc3-of-simple.o -obj-$(CONFIG_USB_XHCI_ROCKCHIP) += xhci-rockchip.o obj-$(CONFIG_USB_XHCI_EXYNOS) += xhci-exynos5.o obj-$(CONFIG_USB_XHCI_FSL) += xhci-fsl.o obj-$(CONFIG_USB_XHCI_MVEBU) += xhci-mvebu.o
drivers/usb/host/xhci-rockchip.c deleted +0 -196
196 lines not on this page · raw message
Signature · 1 line
2.17.1
PATCH v3 6/7 ARM: dts: rk3399-evb: usb3.0 host support
In reply to Frank WangConfigure 'tcphy1' and 'usbdrd_dwc3_1' nodes to support USB3.0 host for Rockchip RK3399 Evaluation Board.
---
Changes for v3:
- drop dtsi changes to keep the same with Linux Kernel.
- amend rk3399-evb.dts to support usb3.0 host.
arch/arm/dts/rk3399-evb.dts | 13 +++++++++++++ 1 file changed, 13 insertions(+)
arch/arm/dts/rk3399-evb.dts +13 -0
@@ -417,6 +417,10 @@ status = "disabled"; }; +&tcphy1 { + status = "okay"; +}; + &u2phy0 { status = "okay"; };
@@ -439,6 +443,15 @@ status = "okay"; }; +&usbdrd3_1 { + status = "okay"; +}; + +&usbdrd_dwc3_1 { + dr_mode = "host"; + status = "okay"; +}; + &usb_host0_ehci { status = "okay"; };
Signature · 1 line
2.17.1
PATCH v3 6/7 ARM: dts: rk3399-evb: usb3.0 host support
Quoted 9 lines · Frank Wang
Configure 'tcphy1' and '
usbdrd_dwc3_1' nodes to support USB3.0 host for Rockchip RK3399 Evaluation Board.Signed-off-by Frank Wang <[email protected]>---
Changes for v3:
- drop dtsi changes to keep the same with Linux Kernel.
- amendrk3399-evb.dtsto support usb3.0 host.
If this is specific to U-Boot it should go in arch/arm/dts/rk3399-evb-u-boot.dtsi as the rk3399-evb.dts is intended to be the same as what's in Linux.
Quoted 39 lines
arch/arm/dts/rk3399-evb.dts | 13 +++++++++++++ 1 file changed, 13 insertions(+)arch/arm/dts/rk3399-evb.dts +13
-1@@ -417,6 +417,10 @@ status = "disabled"; }; +&tcphy1 { + status = "okay"; +}; + &u2phy0 { status = "okay"; };@@ -439,6 +443,15 @@ status = "okay"; }; +&usbdrd3_1 { + status = "okay"; +}; + +&usbdrd_dwc3_1 { + dr_mode = "host"; + status = "okay"; +}; + &usb_host0_ehci { status = "okay"; }; --2.17.1
PATCH v3 6/7 ARM: dts: rk3399-evb: usb3.0 host support
Hi Peter,
Quoted 4 lines · Peter Robinson
Quoted 3 lines · Frank Wang
Configure 'tcphy1' and '
usbdrd_dwc3_1' nodes to support USB3.0 host for Rockchip RK3399 Evaluation Board.
Quoted 8 lines
Quoted 5 lines
Signed-off-by Frank Wang <[email protected]>---
Changes for v3:
- drop dtsi changes to keep the same with Linux Kernel.
- amendrk3399-evb.dtsto support usb3.0 host.If this is specific to U-Boot it should go in
arch/arm/dts/rk3399-evb-u-boot.dtsias therk3399-evb.dtsis intended to be the same as what's in Linux.
Will fix.
Quoted 40 lines
Quoted 39 lines
arch/arm/dts/rk3399-evb.dts | 13 +++++++++++++ 1 file changed, 13 insertions(+)arch/arm/dts/rk3399-evb.dts +13
-1@@ -417,6 +417,10 @@ status = "disabled"; }; +&tcphy1 { + status = "okay"; +}; + &u2phy0 { status = "okay"; };@@ -439,6 +443,15 @@ status = "okay"; }; +&usbdrd3_1 { + status = "okay"; +}; + +&usbdrd_dwc3_1 { + dr_mode = "host"; + status = "okay"; +}; + &usb_host0_ehci { status = "okay"; }; --2.17.1
PATCH v3 7/7 configs: evb-rk3399: update support usb3.0 host
In reply to Frank WangUpdate evb-rk3399 default config to support USB3.0 Host.
---
Changes for v3:
- select more config to support USB3.0 host.
configs/evb-rk3399_defconfig | 6 ++++++ 1 file changed, 6 insertions(+)
configs/evb-rk3399_defconfig +6 -0
@@ -28,6 +28,7 @@ CONFIG_SYS_RELOC_GD_ENV_ADDR=y CONFIG_NET_RANDOM_ETHADDR=y CONFIG_ROCKCHIP_GPIO=y CONFIG_SYS_I2C_ROCKCHIP=y +CONFIG_MISC=y CONFIG_MMC_DW=y CONFIG_MMC_SDHCI=y CONFIG_MMC_SDHCI_ROCKCHIP=y
@@ -35,10 +36,13 @@ CONFIG_SF_DEFAULT_SPEED=20000000 CONFIG_DM_ETH=y CONFIG_ETH_DESIGNWARE=y CONFIG_GMAC_ROCKCHIP=y +CONFIG_PHY_ROCKCHIP_INNO_USB2=y +CONFIG_PHY_ROCKCHIP_TYPEC=y CONFIG_PMIC_RK8XX=y CONFIG_REGULATOR_PWM=y CONFIG_REGULATOR_RK8XX=y CONFIG_PWM_ROCKCHIP=y +CONFIG_DM_RESET=y CONFIG_DM_RNG=y CONFIG_RNG_ROCKCHIP=y CONFIG_BAUDRATE=1500000
@@ -49,6 +53,8 @@ CONFIG_USB_XHCI_HCD=y CONFIG_USB_XHCI_DWC3=y CONFIG_USB_EHCI_HCD=y CONFIG_USB_EHCI_GENERIC=y +CONFIG_USB_DWC3=y +CONFIG_USB_DWC3_GENERIC=y CONFIG_USB_HOST_ETHER=y CONFIG_USB_ETHER_ASIX=y CONFIG_USB_ETHER_ASIX88179=y
Signature · 1 line
2.17.1
PATCH v3 7/7 configs: evb-rk3399: update support usb3.0 host
Quoted 38 lines · Frank Wang
Update evb-rk3399 default config to support USB3.0 Host.
Signed-off-by Frank Wang <[email protected]>---
Changes for v3:
- select more config to support USB3.0 host.configs/evb-rk3399_defconfig | 6 ++++++ 1 file changed, 6 insertions(+)configs/evb-rk3399_defconfig +4
-0@@ -28,6 +28,7 @@ CONFIG_SYS_RELOC_GD_ENV_ADDR=y CONFIG_NET_RANDOM_ETHADDR=y CONFIG_ROCKCHIP_GPIO=y CONFIG_SYS_I2C_ROCKCHIP=y +CONFIG_MISC=y CONFIG_MMC_DW=y CONFIG_MMC_SDHCI=y CONFIG_MMC_SDHCI_ROCKCHIP=y@@ -35,10 +36,13 @@ CONFIG_SF_DEFAULT_SPEED=20000000 CONFIG_DM_ETH=y CONFIG_ETH_DESIGNWARE=y CONFIG_GMAC_ROCKCHIP=y +CONFIG_PHY_ROCKCHIP_INNO_USB2=y +CONFIG_PHY_ROCKCHIP_TYPEC=y CONFIG_PMIC_RK8XX=y CONFIG_REGULATOR_PWM=y CONFIG_REGULATOR_RK8XX=y CONFIG_PWM_ROCKCHIP=y +CONFIG_DM_RESET=y CONFIG_DM_RNG=y CONFIG_RNG_ROCKCHIP=y CONFIG_BAUDRATE=1500000
configs/evb-rk3399_defconfig CONFIG_USB_XHCI_HCD=y · line 57
Quoted 5 lines
configs/evb-rk3399_defconfig +2
-0@@ -49,6 +53,8 @@ CONFIG_USB_XHCI_HCD=y CONFIG_USB_XHCI_DWC3=y CONFIG_USB_EHCI_HCD=y CONFIG_USB_EHCI_GENERIC=y +CONFIG_USB_DWC3=y +CONFIG_USB_DWC3_GENERIC=y
We need to enable OF_LIVE otherwise phy_type would be 0 but the actual one is 0x2 (utmi_wide). For phy_type 0 device cannot respond to the set address.
scanning bus dwc3 for devices... Device not responding to set address.
USB device not accepting new address (error=80000000)
1 USB Device(s) found
scanning usb for storage devices... 0 Storage Device(s) found
Jagan.
PATCH v3 7/7 configs: evb-rk3399: update support usb3.0 host
Quoted 49 lines · Jagan Teki
Quoted 38 lines · Frank Wang
Update evb-rk3399 default config to support USB3.0 Host.
Signed-off-by Frank Wang <[email protected]>---
Changes for v3:
- select more config to support USB3.0 host.configs/evb-rk3399_defconfig | 6 ++++++ 1 file changed, 6 insertions(+)configs/evb-rk3399_defconfig +4
-0@@ -28,6 +28,7 @@ CONFIG_SYS_RELOC_GD_ENV_ADDR=y CONFIG_NET_RANDOM_ETHADDR=y CONFIG_ROCKCHIP_GPIO=y CONFIG_SYS_I2C_ROCKCHIP=y +CONFIG_MISC=y CONFIG_MMC_DW=y CONFIG_MMC_SDHCI=y CONFIG_MMC_SDHCI_ROCKCHIP=y@@ -35,10 +36,13 @@ CONFIG_SF_DEFAULT_SPEED=20000000 CONFIG_DM_ETH=y CONFIG_ETH_DESIGNWARE=y CONFIG_GMAC_ROCKCHIP=y +CONFIG_PHY_ROCKCHIP_INNO_USB2=y +CONFIG_PHY_ROCKCHIP_TYPEC=y CONFIG_PMIC_RK8XX=y CONFIG_REGULATOR_PWM=y CONFIG_REGULATOR_RK8XX=y CONFIG_PWM_ROCKCHIP=y +CONFIG_DM_RESET=y CONFIG_DM_RNG=y CONFIG_RNG_ROCKCHIP=y CONFIG_BAUDRATE=1500000configs/evb-rk3399_defconfig CONFIG_USB_XHCI_HCD=y · line 57
Quoted 5 lines
configs/evb-rk3399_defconfig +2
-0@@ -49,6 +53,8 @@ CONFIG_USB_XHCI_HCD=y CONFIG_USB_XHCI_DWC3=y CONFIG_USB_EHCI_HCD=y CONFIG_USB_EHCI_GENERIC=y +CONFIG_USB_DWC3=y +CONFIG_USB_DWC3_GENERIC=yWe need to enable
OF_LIVEotherwisephy_typewould be 0 but the actual one is0x2(utmi_wide). Forphy_type0 device cannot respond to the set address.
Quoted 4 lines
scanning bus dwc3 for devices... Device not responding to set address.
USB device not accepting new address (error=80000000)
1 USB Device(s) found
scanning usb for storage devices... 0 Storage Device(s) found
How is OF_LIVE related to setting the phy width ?
PATCH v3 7/7 configs: evb-rk3399: update support usb3.0 host
Quoted 51 lines · Marek Vasut
Quoted 49 lines · Jagan Teki
Quoted 38 lines · Frank Wang
Update evb-rk3399 default config to support USB3.0 Host.
Signed-off-by Frank Wang <[email protected]>---
Changes for v3:
- select more config to support USB3.0 host.configs/evb-rk3399_defconfig | 6 ++++++ 1 file changed, 6 insertions(+)configs/evb-rk3399_defconfig +4
-0@@ -28,6 +28,7 @@ CONFIG_SYS_RELOC_GD_ENV_ADDR=y CONFIG_NET_RANDOM_ETHADDR=y CONFIG_ROCKCHIP_GPIO=y CONFIG_SYS_I2C_ROCKCHIP=y +CONFIG_MISC=y CONFIG_MMC_DW=y CONFIG_MMC_SDHCI=y CONFIG_MMC_SDHCI_ROCKCHIP=y@@ -35,10 +36,13 @@ CONFIG_SF_DEFAULT_SPEED=20000000 CONFIG_DM_ETH=y CONFIG_ETH_DESIGNWARE=y CONFIG_GMAC_ROCKCHIP=y +CONFIG_PHY_ROCKCHIP_INNO_USB2=y +CONFIG_PHY_ROCKCHIP_TYPEC=y CONFIG_PMIC_RK8XX=y CONFIG_REGULATOR_PWM=y CONFIG_REGULATOR_RK8XX=y CONFIG_PWM_ROCKCHIP=y +CONFIG_DM_RESET=y CONFIG_DM_RNG=y CONFIG_RNG_ROCKCHIP=y CONFIG_BAUDRATE=1500000configs/evb-rk3399_defconfig CONFIG_USB_XHCI_HCD=y · line 57
Quoted 5 lines
configs/evb-rk3399_defconfig +2
-0@@ -49,6 +53,8 @@ CONFIG_USB_XHCI_HCD=y CONFIG_USB_XHCI_DWC3=y CONFIG_USB_EHCI_HCD=y CONFIG_USB_EHCI_GENERIC=y +CONFIG_USB_DWC3=y +CONFIG_USB_DWC3_GENERIC=yWe need to enable
OF_LIVEotherwisephy_typewould be 0 but the actual one is0x2(utmi_wide). Forphy_type0 device cannot respond to the set address.
Quoted 6 lines
Quoted 4 lines
scanning bus dwc3 for devices... Device not responding to set address.
USB device not accepting new address (error=80000000)
1 USB Device(s) found
scanning usb for storage devices... 0 Storage Device(s) foundHow is
OF_LIVErelated to setting the phy width ?
One of Frank patch [1] get the phy_type with OF_LIVE build depending.
[1] https://patchwork.ozlabs.org/project/uboot/patch/20200507081213.16107-4-frank.wang at rock-chips.com/
PATCH v3 7/7 configs: evb-rk3399: update support usb3.0 host
Quoted 57 lines · Jagan Teki
Quoted 56 lines · Marek Vasut
Quoted 53 lines · Jagan Teki
Quoted 38 lines · Frank Wang
Update evb-rk3399 default config to support USB3.0 Host.
Signed-off-by Frank Wang <[email protected]>---
Changes for v3:
- select more config to support USB3.0 host.configs/evb-rk3399_defconfig | 6 ++++++ 1 file changed, 6 insertions(+)configs/evb-rk3399_defconfig +4
-0@@ -28,6 +28,7 @@ CONFIG_SYS_RELOC_GD_ENV_ADDR=y CONFIG_NET_RANDOM_ETHADDR=y CONFIG_ROCKCHIP_GPIO=y CONFIG_SYS_I2C_ROCKCHIP=y +CONFIG_MISC=y CONFIG_MMC_DW=y CONFIG_MMC_SDHCI=y CONFIG_MMC_SDHCI_ROCKCHIP=y@@ -35,10 +36,13 @@ CONFIG_SF_DEFAULT_SPEED=20000000 CONFIG_DM_ETH=y CONFIG_ETH_DESIGNWARE=y CONFIG_GMAC_ROCKCHIP=y +CONFIG_PHY_ROCKCHIP_INNO_USB2=y +CONFIG_PHY_ROCKCHIP_TYPEC=y CONFIG_PMIC_RK8XX=y CONFIG_REGULATOR_PWM=y CONFIG_REGULATOR_RK8XX=y CONFIG_PWM_ROCKCHIP=y +CONFIG_DM_RESET=y CONFIG_DM_RNG=y CONFIG_RNG_ROCKCHIP=y CONFIG_BAUDRATE=1500000configs/evb-rk3399_defconfig CONFIG_USB_XHCI_HCD=y · line 57
Quoted 5 lines
configs/evb-rk3399_defconfig +2
-0@@ -49,6 +53,8 @@ CONFIG_USB_XHCI_HCD=y CONFIG_USB_XHCI_DWC3=y CONFIG_USB_EHCI_HCD=y CONFIG_USB_EHCI_GENERIC=y +CONFIG_USB_DWC3=y +CONFIG_USB_DWC3_GENERIC=yWe need to enable
OF_LIVEotherwisephy_typewould be 0 but the actual one is0x2(utmi_wide). Forphy_type0 device cannot respond to the set address.scanning bus dwc3 for devices... Device not responding to set address.
USB device not accepting new address (error=80000000)
1 USB Device(s) found
scanning usb for storage devices... 0 Storage Device(s) found
Quoted 5 lines
Quoted 1 line
How is
OF_LIVErelated to setting the phy width ?One of Frank patch [1] get the
phy_typewithOF_LIVEbuild depending.[1] https://patchwork.ozlabs.org/project/uboot/patch/20200507081213.16107-4-frank.wang at rock-chips.com/
Maybe that needs to be fixed, to work even without OF_LIVE ?
PATCH v3 7/7 configs: evb-rk3399: update support usb3.0 host
Quoted 59 lines · Marek Vasut
Quoted 57 lines · Jagan Teki
Quoted 56 lines · Marek Vasut
Quoted 53 lines · Jagan Teki
Quoted 38 lines · Frank Wang
Update evb-rk3399 default config to support USB3.0 Host.
Signed-off-by Frank Wang <[email protected]>---
Changes for v3:
- select more config to support USB3.0 host.configs/evb-rk3399_defconfig | 6 ++++++ 1 file changed, 6 insertions(+)configs/evb-rk3399_defconfig +4
-0@@ -28,6 +28,7 @@ CONFIG_SYS_RELOC_GD_ENV_ADDR=y CONFIG_NET_RANDOM_ETHADDR=y CONFIG_ROCKCHIP_GPIO=y CONFIG_SYS_I2C_ROCKCHIP=y +CONFIG_MISC=y CONFIG_MMC_DW=y CONFIG_MMC_SDHCI=y CONFIG_MMC_SDHCI_ROCKCHIP=y@@ -35,10 +36,13 @@ CONFIG_SF_DEFAULT_SPEED=20000000 CONFIG_DM_ETH=y CONFIG_ETH_DESIGNWARE=y CONFIG_GMAC_ROCKCHIP=y +CONFIG_PHY_ROCKCHIP_INNO_USB2=y +CONFIG_PHY_ROCKCHIP_TYPEC=y CONFIG_PMIC_RK8XX=y CONFIG_REGULATOR_PWM=y CONFIG_REGULATOR_RK8XX=y CONFIG_PWM_ROCKCHIP=y +CONFIG_DM_RESET=y CONFIG_DM_RNG=y CONFIG_RNG_ROCKCHIP=y CONFIG_BAUDRATE=1500000configs/evb-rk3399_defconfig CONFIG_USB_XHCI_HCD=y · line 57
Quoted 5 lines
configs/evb-rk3399_defconfig +2
-0@@ -49,6 +53,8 @@ CONFIG_USB_XHCI_HCD=y CONFIG_USB_XHCI_DWC3=y CONFIG_USB_EHCI_HCD=y CONFIG_USB_EHCI_GENERIC=y +CONFIG_USB_DWC3=y +CONFIG_USB_DWC3_GENERIC=yWe need to enable
OF_LIVEotherwisephy_typewould be 0 but the actual one is0x2(utmi_wide). Forphy_type0 device cannot respond to the set address.scanning bus dwc3 for devices... Device not responding to set address.
USB device not accepting new address (error=80000000)
1 USB Device(s) found
scanning usb for storage devices... 0 Storage Device(s) found
Quoted 7 lines
Quoted 5 lines
Quoted 1 line
How is
OF_LIVErelated to setting the phy width ?One of Frank patch [1] get the
phy_typewithOF_LIVEbuild depending.[1] https://patchwork.ozlabs.org/project/uboot/patch/20200507081213.16107-4-frank.wang at rock-chips.com/
Maybe that needs to be fixed, to work even without
OF_LIVE?
Yes, you are correct. It can get the phy_type value even without OF_LIVE.
PATCH v3 7/7 configs: evb-rk3399: update support usb3.0 host
Hi Marek & Jagan,
Quoted 55 lines · Jagan Teki
Quoted 54 lines · Marek Vasut
Quoted 53 lines · Jagan Teki
Quoted 52 lines · Marek Vasut
Quoted 51 lines · Jagan Teki
Quoted 37 lines · Frank Wang
Update evb-rk3399 default config to support USB3.0 Host.
Signed-off-by Frank Wang <[email protected]>---
Changes for v3:
- select more config to support USB3.0 host.configs/evb-rk3399_defconfig | 6 ++++++ 1 file changed, 6 insertions(+)configs/evb-rk3399_defconfig +4
-0@@ -28,6 +28,7 @@ CONFIG_SYS_RELOC_GD_ENV_ADDR=y CONFIG_NET_RANDOM_ETHADDR=y CONFIG_ROCKCHIP_GPIO=y CONFIG_SYS_I2C_ROCKCHIP=y +CONFIG_MISC=y CONFIG_MMC_DW=y CONFIG_MMC_SDHCI=y CONFIG_MMC_SDHCI_ROCKCHIP=y@@ -35,10 +36,13 @@ CONFIG_SF_DEFAULT_SPEED=20000000 CONFIG_DM_ETH=y CONFIG_ETH_DESIGNWARE=y CONFIG_GMAC_ROCKCHIP=y +CONFIG_PHY_ROCKCHIP_INNO_USB2=y +CONFIG_PHY_ROCKCHIP_TYPEC=y CONFIG_PMIC_RK8XX=y CONFIG_REGULATOR_PWM=y CONFIG_REGULATOR_RK8XX=y CONFIG_PWM_ROCKCHIP=y +CONFIG_DM_RESET=y CONFIG_DM_RNG=y CONFIG_RNG_ROCKCHIP=y CONFIG_BAUDRATE=1500000configs/evb-rk3399_defconfig CONFIG_USB_XHCI_HCD=y · line 57
Quoted 5 lines
configs/evb-rk3399_defconfig +2
-0@@ -49,6 +53,8 @@ CONFIG_USB_XHCI_HCD=y CONFIG_USB_XHCI_DWC3=y CONFIG_USB_EHCI_HCD=y CONFIG_USB_EHCI_GENERIC=y +CONFIG_USB_DWC3=y +CONFIG_USB_DWC3_GENERIC=yWe need to enable
OF_LIVEotherwisephy_typewould be 0 but the actual one is0x2(utmi_wide). Forphy_type0 device cannot respond to the set address.scanning bus dwc3 for devices... Device not responding to set address.
USB device not accepting new address (error=80000000)
1 USB Device(s) found
scanning usb for storage devices... 0 Storage Device(s) found
Quoted 6 lines
Quoted 5 lines
Quoted 4 lines
Quoted 1 line
How is
OF_LIVErelated to setting the phy width ?One of Frank patch [1] get the
phy_typewithOF_LIVEbuild depending.[1] https://patchwork.ozlabs.org/project/uboot/patch/20200507081213.16107-4-frank.wang at rock-chips.com/
Maybe that needs to be fixed, to work even without
OF_LIVE?Yes, you are correct. It can get the
phy_typevalue even withoutOF_LIVE.
Okay, keep 'CONFIG_DM_USB' only and fix it in next patch.
BR,
Frank