platform/x86: Add new intel_atomisp2_led driver
PATCH 1/1 platform/x86: Add new intel_atomisp2_led driver
Many Bay Trail and Cherry Trail devices come with a camera attached to Intel's Image Signal Processor. Linux currently does not have a driver for these, so they do not work as a camera.
Some of these camera's have a status LED which is controlled through a GPIO in some cases, e.g. on the Asus T100TA and Asus T200TA, there is a firmware issue where the LED gets turned on at boot.
This commit adds a Linux LED driver for the camera LED on these devices. This driver will turn the LED off at boot and also allows controlling the LED (so the user can repurpose it) through the sysfs LED interface.
Which GPIO is attached to the LED is usually not described in the ACPI tables, so this driver contains per-system info about the GPIO inside the driver. This means that this driver only works on systems the driver knows about.
--- MAINTAINERS | 6 ++ drivers/platform/x86/Kconfig | 21 ++++ drivers/platform/x86/Makefile | 1 + drivers/platform/x86/intel_atomisp2_led.c | 118 ++++++++++++++++++++++ 4 files changed, 146 insertions(+) create mode 100644 drivers/platform/x86/intel_atomisp2_led.c
MAINTAINERS +6 -0
@@ -8499,6 +8499,12 @@ L: [email protected] S: Maintained F: drivers/platform/x86/intel_atomisp2_pm.c +INTEL ATOMISP2 LED DRIVER +M: Hans de Goede <[email protected]> +L: [email protected] +S: Maintained +F: drivers/platform/x86/intel_atomisp2_led.c + INTEL C600 SERIES SAS CONTROLLER DRIVER M: Intel SCU Linux support <[email protected]> M: Artur Paszkiewicz <[email protected]>
drivers/platform/x86/Kconfig +21 -0
@@ -750,6 +750,27 @@ config INTEL_ATOMISP2_PM To compile this driver as a module, choose M here: the module will be called intel_atomisp2_pm. +config INTEL_ATOMISP2_LED + tristate "Intel AtomISP2 camera LED driver" + depends on GPIOLIB && LEDS_GPIO + help + Many Bay Trail and Cherry Trail devices come with a camera attached + to Intel's Image Signal Processor. Linux currently does not have a + driver for these, so they do not work as a camera. Some of these + camera's have a LED which is controlled through a GPIO. + + Some of these devices have a firmware issue where the LED gets turned + on at boot. This driver will turn the LED off at boot and also allows + controlling the LED (repurposing it) through the sysfs LED interface. + + Which GPIO is attached to the LED is usually not described in the + ACPI tables, so this driver contains per-system info about the GPIO + inside the driver, this means that this driver only works on systems + the driver knows about. + + To compile this driver as a module, choose M here: the module + will be called intel_atomisp2_led. + config INTEL_CHT_INT33FE tristate "Intel Cherry Trail ACPI INT33FE Driver" depends on X86 && ACPI && I2C && REGULATOR
drivers/platform/x86/Makefile +1 -0
@@ -69,6 +69,7 @@ obj-$(CONFIG_THINKPAD_ACPI) += thinkpad_acpi.o # Intel obj-$(CONFIG_INTEL_ATOMISP2_PM) += intel_atomisp2_pm.o +obj-$(CONFIG_INTEL_ATOMISP2_LED) += intel_atomisp2_led.o obj-$(CONFIG_INTEL_CHT_INT33FE) += intel_cht_int33fe.o intel_cht_int33fe-objs := intel_cht_int33fe_common.o \ intel_cht_int33fe_typec.o \
drivers/platform/x86/intel_atomisp2_led.c new file +118 -0
118 lines not on this page · raw message
Signature · 1 line
2.26.0
Quoted 9 lines · Hans de Goede
Many Bay Trail and Cherry Trail devices come with a camera attached to Intel's Image Signal Processor. Linux currently does not have a driver for these, so they do not work as a camera.
Some of these camera's have a status LED which is controlled through a GPIO in some cases, e.g. on the Asus T100TA and Asus T200TA, there is a firmware issue where the LED gets turned on at boot.
Quoted 9 lines
This commit adds a Linux LED driver for the camera LED on these devices. This driver will turn the LED off at boot and also allows controlling the LED (so the user can repurpose it) through the sysfs LED interface.
Which GPIO is attached to the LED is usually not described in the ACPI tables, so this driver contains per-system info about the GPIO inside the driver. This means that this driver only works on systems the driver knows about.
Somehow I missed it, sorry.
It doesn't apply to for-next. Also I have a question. Since Mauro tries to resurrect AtomISP v2, can we somehow do this in a way it can be easily disabled / not conflicting with the real driver? Or do we need this at all after driver will be in place?
Quoted 197 lines
Signed-off-by Hans de Goede <[email protected]>--- MAINTAINERS | 6 ++ drivers/platform/x86/Kconfig | 21 ++++ drivers/platform/x86/Makefile | 1 + drivers/platform/x86/intel_atomisp2_led.c | 118 ++++++++++++++++++++++ 4 files changed, 146 insertions(+) create mode 100644 drivers/platform/x86/intel_atomisp2_led.cMAINTAINERS +6
-0@@ -8499,6 +8499,12 @@ L: [email protected] S: Maintained F: drivers/platform/x86/intel_atomisp2_pm.c +INTEL ATOMISP2 LED DRIVER +M: Hans de Goede <[email protected]> +L: [email protected] +S: Maintained +F: drivers/platform/x86/intel_atomisp2_led.c + INTEL C600 SERIES SAS CONTROLLER DRIVER M: Intel SCU Linux support <[email protected]> M: Artur Paszkiewicz <[email protected]>drivers/platform/x86/Kconfig +21
-0@@ -750,6 +750,27 @@ config INTEL_ATOMISP2_PM To compile this driver as a module, choose M here: the module will be called intel_atomisp2_pm. +config INTEL_ATOMISP2_LED + tristate "Intel AtomISP2 camera LED driver" + depends on GPIOLIB && LEDS_GPIO + help + Many Bay Trail and Cherry Trail devices come with a camera attached + to Intel's Image Signal Processor. Linux currently does not have a + driver for these, so they do not work as a camera. Some of these + camera's have a LED which is controlled through a GPIO. + + Some of these devices have a firmware issue where the LED gets turned + on at boot. This driver will turn the LED off at boot and also allows + controlling the LED (repurposing it) through the sysfs LED interface. + + Which GPIO is attached to the LED is usually not described in the + ACPI tables, so this driver contains per-system info about the GPIO + inside the driver, this means that this driver only works on systems + the driver knows about. + + To compile this driver as a module, choose M here: the module + will be called intel_atomisp2_led. + config INTEL_CHT_INT33FE tristate "Intel Cherry Trail ACPI INT33FE Driver" depends on X86 && ACPI && I2C && REGULATORdrivers/platform/x86/Makefile +1
-0@@ -69,6 +69,7 @@ obj-$(CONFIG_THINKPAD_ACPI) += thinkpad_acpi.o # Intel obj-$(CONFIG_INTEL_ATOMISP2_PM) += intel_atomisp2_pm.o +obj-$(CONFIG_INTEL_ATOMISP2_LED) += intel_atomisp2_led.o obj-$(CONFIG_INTEL_CHT_INT33FE) += intel_cht_int33fe.o intel_cht_int33fe-objs := intel_cht_int33fe_common.o \ intel_cht_int33fe_typec.o \drivers/platform/x86/intel_atomisp2_led.c new file +118
-1@@ -0,0 +1,118 @@ +// SPDX-License-Identifier: GPL-2.0+ +/* +* Driver for controlling LEDs for cameras connected to the Intel atomisp2 +* The main purpose of this driver is to turn off LEDs which are on at boot. +* +* Copyright (C) 2020 Hans de Goede <[email protected]> +*/ + +#include <linux/dmi.h> +#include <linux/gpio/consumer.h> +#include <linux/gpio/machine.h> +#include <linux/leds.h> +#include <linux/module.h> +#include <linux/mod_devicetable.h> +#include <linux/platform_device.h> +#include <linux/workqueue.h> + +/* This must be leds-gpio as the leds-gpio driver binds to the name */ +#define DEV_NAME "leds-gpio" + +static const struct gpio_led atomisp2_leds[] = { + { + .name ="atomisp2::camera" , + .default_state =LEDS_GPIO_DEFSTATE_OFF , + }, +}; + +static const struct gpio_led_platform_data atomisp2_leds_pdata = { + .num_leds =ARRAY_SIZE (atomisp2_leds), + .leds = atomisp2_leds, +}; + +static struct gpiod_lookup_table asus_t100ta_lookup = { + .dev_id =DEV_NAME , + .table = { +GPIO_LOOKUP_IDX ("INT33FC:02" ,8 ,NULL ,0 ,GPIO_ACTIVE_HIGH ), + { } + } +}; + +static struct gpiod_lookup_table asus_t100chi_lookup = { + .dev_id =DEV_NAME , + .table = { +GPIO_LOOKUP_IDX ("INT33FC:01" ,24 ,NULL ,0 ,GPIO_ACTIVE_HIGH ), + { } + } +}; + +static const struct dmi_system_id atomisp2_led_systems[]__initconst = { + { + .matches = { +DMI_EXACT_MATCH (DMI_SYS_VENDOR ,"ASUSTeK COMPUTER INC." ), +DMI_EXACT_MATCH (DMI_PRODUCT_NAME ,"T100TA" ), + }, + .driver_data = &asus_t100ta_lookup, + }, + { + .matches = { +DMI_EXACT_MATCH (DMI_SYS_VENDOR ,"ASUSTeK COMPUTER INC." ), +DMI_EXACT_MATCH (DMI_PRODUCT_NAME ,"T200TA" ), + }, + .driver_data = &asus_t100ta_lookup, + }, + { + .matches = { +DMI_EXACT_MATCH (DMI_SYS_VENDOR ,"ASUSTeK COMPUTER INC." ), +DMI_EXACT_MATCH (DMI_PRODUCT_NAME ,"T100CHI" ), + }, + .driver_data = &asus_t100chi_lookup, + }, + {}/* Terminating entry */ +}; +MODULE_DEVICE_TABLE (dmi, atomisp2_led_systems); + +static struct gpiod_lookup_table *gpio_lookup; +static struct platform_device *pdev; + +static int __init atomisp2_led_init (void ) +{ +const struct dmi_system_id *system; + + system =dmi_first_match (atomisp2_led_systems); +if (!system) +return -ENODEV ; + + gpio_lookup = system->driver_data; +gpiod_add_lookup_table (gpio_lookup); + + pdev =platform_device_register_resndata (NULL , +DEV_NAME ,PLATFORM_DEVID_NONE , +NULL ,0 , &atomisp2_leds_pdata, +sizeof (atomisp2_leds_pdata)); +if (IS_ERR (pdev)) { +gpiod_remove_lookup_table (gpio_lookup); +return PTR_ERR (pdev); + } + +return 0 ; +} + +static void __exit atomisp2_led_cleanup(void) +{ +platform_device_unregister (pdev); +gpiod_remove_lookup_table (gpio_lookup); +} + +module_init (atomisp2_led_init); +module_exit (atomisp2_led_cleanup); + +/* +* The ACPI INIT method from Asus WMI's code on the T100TA and T200TA turns the +* LED on (without the WMI interface allowing further control over the LED). +* Ensure we are loaded after asus-nb-wmi so that we turn the LED off again. +*/ +MODULE_SOFTDEP ("pre: asus_nb_wmi" ); +MODULE_AUTHOR ("Hans de Goede <[email protected]" ); +MODULE_DESCRIPTION ("Intel atomisp2 camera LED driver" ); +MODULE_LICENSE ("GPL" ); --2.26.0
Signature · 2 lines
With Best Regards, Andy Shevchenko
Hi,
Quoted 14 lines · Andy Shevchenko
Quoted 13 lines · Hans de Goede
Many Bay Trail and Cherry Trail devices come with a camera attached to Intel's Image Signal Processor. Linux currently does not have a driver for these, so they do not work as a camera.
Some of these camera's have a status LED which is controlled through a GPIO in some cases, e.g. on the Asus T100TA and Asus T200TA, there is a firmware issue where the LED gets turned on at boot.
This commit adds a Linux LED driver for the camera LED on these devices. This driver will turn the LED off at boot and also allows controlling the LED (so the user can repurpose it) through the sysfs LED interface.
Quoted 7 lines
Quoted 5 lines
Which GPIO is attached to the LED is usually not described in the ACPI tables, so this driver contains per-system info about the GPIO inside the driver. This means that this driver only works on systems the driver knows about.
Somehow I missed it, sorry.
No problem.
Quoted 3 lines
It doesn't apply to for-next. Also I have a question. Since Mauro tries to resurrect AtomISP v2, can we somehow do this in a way it can be easily disabled / not conflicting with the real driver?
Mauro is working on resurrecting AtomISP v2 support for Cherry Trail, the devices which are on the DMI match list of this driver so far are all Bay Trail based. I think it is safe to say that Bay Trail AtomISP v2 support still is very far away.
Quoted 1 line
Or do we need this at all after driver will be in place?
We may still need / want this even if there is an Atom ISP v2 driver. The question is if that driver will then control the LED itself (using hardcoded per model info embedded in that driver) or if it will use a LED-trigger + a separate LED driver, if we go the LED-trigger route, then we want to keep this driver around as the actual LED driver.
Do you have any more (initial) review remarks, before I do a rebase + resend ?
Regards,
Hans
Quoted 200 lines
Quoted 198 lines
Signed-off-by Hans de Goede <[email protected]>--- MAINTAINERS | 6 ++ drivers/platform/x86/Kconfig | 21 ++++ drivers/platform/x86/Makefile | 1 + drivers/platform/x86/intel_atomisp2_led.c | 118 ++++++++++++++++++++++ 4 files changed, 146 insertions(+)create mode 100644
drivers/platform/x86/intel_atomisp2_led.cMAINTAINERS +6
-0@@ -8499,6 +8499,12 @@ L: [email protected] S: Maintained F: drivers/platform/x86/intel_atomisp2_pm.c +INTEL ATOMISP2 LED DRIVER +M: Hans de Goede <[email protected]> +L: [email protected] +S: Maintained +F: drivers/platform/x86/intel_atomisp2_led.c + INTEL C600 SERIES SAS CONTROLLER DRIVER M: Intel SCU Linux support <[email protected]> M: Artur Paszkiewicz <[email protected]>drivers/platform/x86/Kconfig +21
-0@@ -750,6 +750,27 @@ config INTEL_ATOMISP2_PM To compile this driver as a module, choose M here: the module will be called intel_atomisp2_pm. +config INTEL_ATOMISP2_LED + tristate "Intel AtomISP2 camera LED driver" + depends on GPIOLIB && LEDS_GPIO + help + Many Bay Trail and Cherry Trail devices come with a camera attached + to Intel's Image Signal Processor. Linux currently does not have a + driver for these, so they do not work as a camera. Some of these + camera's have a LED which is controlled through a GPIO. + + Some of these devices have a firmware issue where the LED gets turned + on at boot. This driver will turn the LED off at boot and also allows + controlling the LED (repurposing it) through the sysfs LED interface. + + Which GPIO is attached to the LED is usually not described in the + ACPI tables, so this driver contains per-system info about the GPIO + inside the driver, this means that this driver only works on systems + the driver knows about. + + To compile this driver as a module, choose M here: the module + will be called intel_atomisp2_led. + config INTEL_CHT_INT33FE tristate "Intel Cherry Trail ACPI INT33FE Driver" depends on X86 && ACPI && I2C && REGULATORdrivers/platform/x86/Makefile +1
-0@@ -69,6 +69,7 @@ obj-$(CONFIG_THINKPAD_ACPI) += thinkpad_acpi.o # Intel obj-$(CONFIG_INTEL_ATOMISP2_PM) += intel_atomisp2_pm.o +obj-$(CONFIG_INTEL_ATOMISP2_LED) += intel_atomisp2_led.o obj-$(CONFIG_INTEL_CHT_INT33FE) += intel_cht_int33fe.o intel_cht_int33fe-objs := intel_cht_int33fe_common.o \ intel_cht_int33fe_typec.o \drivers/platform/x86/intel_atomisp2_led.c new file +118
-1@@ -0,0 +1,118 @@ +// SPDX-License-Identifier: GPL-2.0+ +/* +* Driver for controlling LEDs for cameras connected to the Intel atomisp2 +* The main purpose of this driver is to turn off LEDs which are on at boot. +* +* Copyright (C) 2020 Hans de Goede <[email protected]> +*/ + +#include <linux/dmi.h> +#include <linux/gpio/consumer.h> +#include <linux/gpio/machine.h> +#include <linux/leds.h> +#include <linux/module.h> +#include <linux/mod_devicetable.h> +#include <linux/platform_device.h> +#include <linux/workqueue.h> + +/* This must be leds-gpio as the leds-gpio driver binds to the name */ +#define DEV_NAME "leds-gpio" + +static const struct gpio_led atomisp2_leds[] = { + { + .name ="atomisp2::camera" , + .default_state =LEDS_GPIO_DEFSTATE_OFF , + }, +}; + +static const struct gpio_led_platform_data atomisp2_leds_pdata = { + .num_leds =ARRAY_SIZE (atomisp2_leds), + .leds = atomisp2_leds, +}; + +static struct gpiod_lookup_table asus_t100ta_lookup = { + .dev_id =DEV_NAME , + .table = { +GPIO_LOOKUP_IDX ("INT33FC:02" ,8 ,NULL ,0 ,GPIO_ACTIVE_HIGH ), + { } + } +}; + +static struct gpiod_lookup_table asus_t100chi_lookup = { + .dev_id =DEV_NAME , + .table = { +GPIO_LOOKUP_IDX ("INT33FC:01" ,24 ,NULL ,0 ,GPIO_ACTIVE_HIGH ), + { } + } +}; + +static const struct dmi_system_id atomisp2_led_systems[]__initconst = { + { + .matches = { +DMI_EXACT_MATCH (DMI_SYS_VENDOR ,"ASUSTeK COMPUTER INC." ), +DMI_EXACT_MATCH (DMI_PRODUCT_NAME ,"T100TA" ), + }, + .driver_data = &asus_t100ta_lookup, + }, + { + .matches = { +DMI_EXACT_MATCH (DMI_SYS_VENDOR ,"ASUSTeK COMPUTER INC." ), +DMI_EXACT_MATCH (DMI_PRODUCT_NAME ,"T200TA" ), + }, + .driver_data = &asus_t100ta_lookup, + }, + { + .matches = { +DMI_EXACT_MATCH (DMI_SYS_VENDOR ,"ASUSTeK COMPUTER INC." ), +DMI_EXACT_MATCH (DMI_PRODUCT_NAME ,"T100CHI" ), + }, + .driver_data = &asus_t100chi_lookup, + }, + {}/* Terminating entry */ +}; +MODULE_DEVICE_TABLE (dmi, atomisp2_led_systems); + +static struct gpiod_lookup_table *gpio_lookup; +static struct platform_device *pdev; + +static int __init atomisp2_led_init (void ) +{ +const struct dmi_system_id *system; + + system =dmi_first_match (atomisp2_led_systems); +if (!system) +return -ENODEV ; + + gpio_lookup = system->driver_data; +gpiod_add_lookup_table (gpio_lookup); + + pdev =platform_device_register_resndata (NULL , +DEV_NAME ,PLATFORM_DEVID_NONE , +NULL ,0 , &atomisp2_leds_pdata, +sizeof (atomisp2_leds_pdata)); +if (IS_ERR (pdev)) { +gpiod_remove_lookup_table (gpio_lookup); +return PTR_ERR (pdev); + } + +return 0 ; +} + +static void __exit atomisp2_led_cleanup(void) +{ +platform_device_unregister (pdev); +gpiod_remove_lookup_table (gpio_lookup); +} + +module_init (atomisp2_led_init); +module_exit (atomisp2_led_cleanup); + +/* +* The ACPI INIT method from Asus WMI's code on the T100TA and T200TA turns the +* LED on (without the WMI interface allowing further control over the LED). +* Ensure we are loaded after asus-nb-wmi so that we turn the LED off again. +*/ +MODULE_SOFTDEP ("pre: asus_nb_wmi" ); +MODULE_AUTHOR ("Hans de Goede <[email protected]" ); +MODULE_DESCRIPTION ("Intel atomisp2 camera LED driver" ); +MODULE_LICENSE ("GPL" ); --2.26.0
Quoted 30 lines · Hans de Goede
Many Bay Trail and Cherry Trail devices come with a camera attached to Intel's Image Signal Processor. Linux currently does not have a driver for these, so they do not work as a camera.
Some of these camera's have a status LED which is controlled through a GPIO in some cases, e.g. on the Asus T100TA and Asus T200TA, there is a firmware issue where the LED gets turned on at boot.
This commit adds a Linux LED driver for the camera LED on these devices. This driver will turn the LED off at boot and also allows controlling the LED (so the user can repurpose it) through the sysfs LED interface.
Which GPIO is attached to the LED is usually not described in the ACPI tables, so this driver contains per-system info about the GPIO inside the driver. This means that this driver only works on systems the driver knows about.
drivers/platform/x86/intel_atomisp2_led.c new file +12
-0+static int __init atomisp2_led_init (void ) +{ +const struct dmi_system_id *system; + + system =dmi_first_match (atomisp2_led_systems); +if (!system) +return -ENODEV ; + + gpio_lookup = system->driver_data; +gpiod_add_lookup_table (gpio_lookup); + + pdev = platform_device_register_resndata(NULL,
drivers/platform/x86/intel_atomisp2_led.c line 98
Quoted 10 lines
drivers/platform/x86/intel_atomisp2_led.c new file +9
-0+DEV_NAME ,PLATFORM_DEVID_NONE , +NULL ,0 , &atomisp2_leds_pdata, + sizeof(atomisp2_leds_pdata)); +if (IS_ERR (pdev)) { +gpiod_remove_lookup_table (gpio_lookup); +return PTR_ERR (pdev); + } + +return 0 ;
return PTR_ERR_OR_ZERO(...);
Quoted 1 line
+}
Signature · 2 lines
With Best Regards, Andy Shevchenko