Skip to contentSkip to conversation

Basic Kontron SMARC-sAL28 board support

PATCH Superseded Michael Walle 2 participants 6 messages May 9, 2020 – Jul 24, 2020 Arm (32-bit)

v3 of 9 Superseded Latest is v9 →

lore
Share & tools
lore
#0 lore raw

v3 cover Basic Kontron SMARC-sAL28 board support

Add basic board support for the Kontron SMARC-sAL28 board. Please note, that this board doesn't support TF-a (yet). Therefore, the u-boot SPL is the first code which is run and it has to set up the RAM.

changes since v3:
- add variant 4 support. Since the atheros PHY dt bindings were merged into master, we can now use them
- add environment section in include/configs/kontron_sl28.h
- add cover letter

changes since v1:
- fix watchdog device tree reference

Michael Walle (2):
armv8: ls1028a: move FSL_LAYERSCAPE to kconfig
board: kontron: add sl28 support

 arch/arm/Kconfig                              |  10 ++
 arch/arm/cpu/armv8/fsl-layerscape/Kconfig     |   1 +
 arch/arm/dts/Makefile                         |   3 +
 .../arm/dts/fsl-ls1028a-kontron-sl28-var3.dts |  14 ++
 .../arm/dts/fsl-ls1028a-kontron-sl28-var4.dts |  42 ++++++
 arch/arm/dts/fsl-ls1028a-kontron-sl28.dts     | 128 ++++++++++++++++++
 board/kontron/sl28/Kconfig                    |  18 +++
 board/kontron/sl28/MAINTAINERS                |   6 +
 board/kontron/sl28/Makefile                   |   8 ++
 board/kontron/sl28/README                     |  63 +++++++++
 board/kontron/sl28/common.c                   |  10 ++
 board/kontron/sl28/ddr.c                      |  98 ++++++++++++++
 board/kontron/sl28/sl28.c                     |  92 +++++++++++++
 board/kontron/sl28/spl.c                      |   9 ++
 configs/kontron_sl28_defconfig                | 102 ++++++++++++++
 include/configs/kontron_sl28.h                | 119 ++++++++++++++++
 include/configs/ls1028a_common.h              |   1 -
 17 files changed, 723 insertions(+), 1 deletion(-)
 create mode 100644 arch/arm/dts/fsl-ls1028a-kontron-sl28-var3.dts
 create mode 100644 arch/arm/dts/fsl-ls1028a-kontron-sl28-var4.dts
 create mode 100644 arch/arm/dts/fsl-ls1028a-kontron-sl28.dts
 create mode 100644 board/kontron/sl28/Kconfig
 create mode 100644 board/kontron/sl28/MAINTAINERS
 create mode 100644 board/kontron/sl28/Makefile
 create mode 100644 board/kontron/sl28/README
 create mode 100644 board/kontron/sl28/common.c
 create mode 100644 board/kontron/sl28/ddr.c
 create mode 100644 board/kontron/sl28/sl28.c
 create mode 100644 board/kontron/sl28/spl.c
 create mode 100644 configs/kontron_sl28_defconfig
 create mode 100644 include/configs/kontron_sl28.h
Signature · 1 line
2.20.1
#1 lore raw

PATCH v3 1/2 armv8: ls1028a: move FSL_LAYERSCAPE to kconfig

CONFIG_FSL_LAYERSCAPE is available in kconfig. There is no need to define it per board; the ls1028a_common.h is really board dependent and only fits to the NXP eval boards. Instead select CONFIG_FSL_LAYERSCAPE when ARCH_LS1028A is selected.

---
 arch/arm/cpu/armv8/fsl-layerscape/Kconfig | 1 +
 include/configs/ls1028a_common.h          | 1 -
 2 files changed, 1 insertion(+), 1 deletion(-)
arch/arm/cpu/armv8/fsl-layerscape/Kconfig +1 -0
index 2f75b2cdd3..116b6b0617 100644
@@ -23,6 +23,7 @@ config ARCH_LS1012A
 config ARCH_LS1028A
 	bool
 	select ARMV8_SET_SMPEN
+	select FSL_LAYERSCAPE
 	select FSL_LSCH3
 	select NXP_LSCH3_2
 	select SYS_FSL_HAS_CCI400
include/configs/ls1028a_common.h +0 -1
index f9040e661d..33d9687eeb 100644
@@ -7,7 +7,6 @@
 #define __L1028A_COMMON_H
 
 #define CONFIG_REMAKE_ELF
-#define CONFIG_FSL_LAYERSCAPE
 #define CONFIG_MP
 
 #include <asm/arch/stream_id_lsch3.h>
Signature · 1 line
2.20.1
#2 lore raw

PATCH v3 2/2 board: kontron: add sl28 support

In reply to Michael Walle

Add basic support for the Kontron SMARC-sAL28 board. This includes just the bare minimum to be able to bring up the board and boot linux.

For now, the Single and Dual PHY variant is supported. Other variants will fall back to the basic variant.

In particular, there is no watchdog support for now. This means that you have to disable the default watchdog, otherwise you'll end up in the recovery bootloader. See the board README for details.

---
 arch/arm/Kconfig                              |  10 ++
 arch/arm/dts/Makefile                         |   3 +
 .../arm/dts/fsl-ls1028a-kontron-sl28-var3.dts |  14 ++
 .../arm/dts/fsl-ls1028a-kontron-sl28-var4.dts |  42 ++++++
 arch/arm/dts/fsl-ls1028a-kontron-sl28.dts     | 128 ++++++++++++++++++
 board/kontron/sl28/Kconfig                    |  18 +++
 board/kontron/sl28/MAINTAINERS                |   6 +
 board/kontron/sl28/Makefile                   |   8 ++
 board/kontron/sl28/README                     |  63 +++++++++
 board/kontron/sl28/common.c                   |  10 ++
 board/kontron/sl28/ddr.c                      |  98 ++++++++++++++
 board/kontron/sl28/sl28.c                     |  92 +++++++++++++
 board/kontron/sl28/spl.c                      |   9 ++
 configs/kontron_sl28_defconfig                | 102 ++++++++++++++
 include/configs/kontron_sl28.h                | 119 ++++++++++++++++
 15 files changed, 722 insertions(+)
 create mode 100644 arch/arm/dts/fsl-ls1028a-kontron-sl28-var3.dts
 create mode 100644 arch/arm/dts/fsl-ls1028a-kontron-sl28-var4.dts
 create mode 100644 arch/arm/dts/fsl-ls1028a-kontron-sl28.dts
 create mode 100644 board/kontron/sl28/Kconfig
 create mode 100644 board/kontron/sl28/MAINTAINERS
 create mode 100644 board/kontron/sl28/Makefile
 create mode 100644 board/kontron/sl28/README
 create mode 100644 board/kontron/sl28/common.c
 create mode 100644 board/kontron/sl28/ddr.c
 create mode 100644 board/kontron/sl28/sl28.c
 create mode 100644 board/kontron/sl28/spl.c
 create mode 100644 configs/kontron_sl28_defconfig
 create mode 100644 include/configs/kontron_sl28.h
arch/arm/Kconfig +10 -0
index 0d463088a2..9fb8d2943c 100644
@@ -1574,6 +1574,15 @@ config TARGET_LS1046AFRWY
 	  development platform that supports the QorIQ LS1046A
 	  Layerscape Architecture processor.
 
+config TARGET_SL28
+	bool "Support sl28"
+	select ARCH_LS1028A
+	select ARM64
+	select ARMV8_MULTIENTRY
+	select SUPPORT_SPL
+	help
+	  Support for Kontron SMARC-sAL28 board.
+
 config TARGET_COLIBRI_PXA270
 	bool "Support colibri_pxa270"
 	select CPU_PXA
@@ -1904,6 +1913,7 @@ source "board/hisilicon/hikey/Kconfig"
 source "board/hisilicon/hikey960/Kconfig"
 source "board/hisilicon/poplar/Kconfig"
 source "board/isee/igep003x/Kconfig"
+source "board/kontron/sl28/Kconfig"
 source "board/phytec/pcm051/Kconfig"
 source "board/silica/pengwyn/Kconfig"
 source "board/spear/spear300/Kconfig"
arch/arm/dts/Makefile +3 -0
index 559d3ab6a7..7050ec72eb 100644
@@ -379,6 +379,9 @@ dtb-$(CONFIG_FSL_LSCH3) += fsl-ls2080a-qds.dtb \
 	fsl-ls2088a-rdb-qspi.dtb \
 	fsl-ls1088a-rdb.dtb \
 	fsl-ls1088a-qds.dtb \
+	fsl-ls1028a-kontron-sl28.dtb \
+	fsl-ls1028a-kontron-sl28-var3.dtb \
+	fsl-ls1028a-kontron-sl28-var4.dtb \
 	fsl-ls1028a-rdb.dtb \
 	fsl-ls1028a-qds-duart.dtb \
 	fsl-ls1028a-qds-lpuart.dtb \
arch/arm/dts/fsl-ls1028a-kontron-sl28-var3.dts new file +14 -0
new file mode 100644
index 0000000000..23f89eadb3
@@ -0,0 +1,14 @@
+// SPDX-License-Identifier: GPL-2.0+
+/*
+ * Kontron SMARC-sAL28 device tree source (Single PHY version)
+ */
+
+/dts-v1/;
+
+#include "fsl-ls1028a-kontron-sl28.dts"
+
+/ {
+	u-boot,dm-pre-reloc;
+	model = "Kontron SMARC-sAL28 Board (Single PHY)";
+	compatible = "kontron,sl28-var3", "kontron,sl28", "fsl,ls1028a";
+};
arch/arm/dts/fsl-ls1028a-kontron-sl28-var4.dts new file +42 -0

42 lines not on this page · raw message

arch/arm/dts/fsl-ls1028a-kontron-sl28.dts new file +128 -0

128 lines not on this page · raw message

board/kontron/sl28/Kconfig new file +18 -0
new file mode 100644
index 0000000000..cdec39be01
@@ -0,0 +1,18 @@
+if TARGET_SL28
+
+config SYS_BOARD
+	default "sl28"
+
+config SYS_VENDOR
+	default "kontron"
+
+config SYS_SOC
+	default "fsl-layerscape"
+
+config SYS_CONFIG_NAME
+	default "kontron_sl28"
+
+config SYS_TEXT_BASE
+	default 0x96000000
+
+endif
board/kontron/sl28/MAINTAINERS new file +6 -0
new file mode 100644
index 0000000000..047a057646
@@ -0,0 +1,6 @@
+Kontron SMARC-sAL28 board
+M:	Michael Walle <[email protected]>
+S:	Maintained
+F:	board/kontron/sl28/
+F:	include/configs/kontron_sl28.h
+F:	configs/kontron_sl28_defconfig
board/kontron/sl28/Makefile new file +8 -0
new file mode 100644
index 0000000000..0f1866c874
@@ -0,0 +1,8 @@
+# SPDX-License-Identifier:	GPL-2.0+
+
+ifndef CONFIG_SPL_BUILD
+obj-y += sl28.o
+endif
+
+obj-y += common.o ddr.o
+obj-$(CONFIG_SPL_BUILD) += spl.o
board/kontron/sl28/README new file +63 -0

63 lines not on this page · raw message

board/kontron/sl28/common.c new file +10 -0
new file mode 100644
index 0000000000..14704f7051
@@ -0,0 +1,10 @@
+// SPDX-License-Identifier: GPL-2.0+
+
+#include <common.h>
+#include <asm/arch-fsl-layerscape/soc.h>
+
+int board_early_init_f(void)
+{
+	fsl_lsch3_early_init_f();
+	return 0;
+}
board/kontron/sl28/ddr.c new file +98 -0

98 lines not on this page · raw message

board/kontron/sl28/sl28.c new file +92 -0

92 lines not on this page · raw message

board/kontron/sl28/spl.c new file +9 -0
new file mode 100644
index 0000000000..eb6d2dc909
@@ -0,0 +1,9 @@
+// SPDX-License-Identifier: GPL-2.0+
+
+#include <common.h>
+#include <asm/spl.h>
+
+void board_boot_order(u32 *spl_boot_list)
+{
+	spl_boot_list[0] = BOOT_DEVICE_SPI;
+}
configs/kontron_sl28_defconfig new file +102 -0

102 lines not on this page · raw message

include/configs/kontron_sl28.h new file +119 -0

119 lines not on this page · raw message

Signature · 1 line
2.20.1
#3 lore raw

PATCH v3 2/2 board: kontron: add sl28 support

Quoted 859 lines

-----Original Message-----
From: U-Boot <[email protected]> On Behalf Of Michael Walle
Sent: Sunday, May 10, 2020 4:50 AM
To: u-boot at lists.denx.de
Cc: Sudhanshu Gupta <[email protected]>; Harninder Rai <[email protected]>; Rajesh Bhagat <[email protected]>; Andy Tang <[email protected]>; Priyanka Jain <[email protected]>; Prabhakar Kushwaha <[email protected]>; Michael Walle <[email protected]>
Subject: [PATCH v3 2/2] board: kontron: add sl28 support

Add basic support for the Kontron SMARC-sAL28 board. This includes just the bare minimum to be able to bring up the board and boot linux.

For now, the Single and Dual PHY variant is supported. Other variants will fall back to the basic variant.

In particular, there is no watchdog support for now. This means that you have to disable the default watchdog, otherwise you'll end up in the recovery bootloader. See the board README for details.

---

arch/arm/Kconfig                              |  10 ++
arch/arm/dts/Makefile                         |   3 +
.../arm/dts/fsl-ls1028a-kontron-sl28-var3.dts |  14 ++  .../arm/dts/fsl-ls1028a-
kontron-sl28-var4.dts |  42 ++++++
arch/arm/dts/fsl-ls1028a-kontron-sl28.dts     | 128 ++++++++++++++++++
board/kontron/sl28/Kconfig                    |  18 +++
board/kontron/sl28/MAINTAINERS                |   6 +
board/kontron/sl28/Makefile                   |   8 ++
board/kontron/sl28/README                     |  63 +++++++++
board/kontron/sl28/common.c                   |  10 ++
board/kontron/sl28/ddr.c                      |  98 ++++++++++++++
board/kontron/sl28/sl28.c                     |  92 +++++++++++++
board/kontron/sl28/spl.c                      |   9 ++
configs/kontron_sl28_defconfig                | 102 ++++++++++++++
include/configs/kontron_sl28.h                | 119 ++++++++++++++++
15 files changed, 722 insertions(+)

create mode 100644 arch/arm/dts/fsl-ls1028a-kontron-sl28-var3.dts create mode 100644 arch/arm/dts/fsl-ls1028a-kontron-sl28-var4.dts create mode 100644 arch/arm/dts/fsl-ls1028a-kontron-sl28.dts create mode 100644 board/kontron/sl28/Kconfig create mode 100644 board/kontron/sl28/MAINTAINERS create mode 100644 board/kontron/sl28/Makefile create mode 100644 board/kontron/sl28/README create mode 100644 board/kontron/sl28/common.c create mode 100644 board/kontron/sl28/ddr.c create mode 100644 board/kontron/sl28/sl28.c create mode 100644 board/kontron/sl28/spl.c create mode 100644 configs/kontron_sl28_defconfig create mode 100644 include/configs/kontron_sl28.h

arch/arm/Kconfig index renamed from arch/arm/Kconfig +0 -0

0d463088a2..9fb8d2943c 100644

arch/arm/Kconfig +9 -0
@@ -1574,6 +1574,15 @@ config TARGET_LS1046AFRWY
 	  development platform that supports the QorIQ LS1046A
 	  Layerscape Architecture processor.
 
+config TARGET_SL28
+	bool "Support sl28"
+	select ARCH_LS1028A
+	select ARM64
+	select ARMV8_MULTIENTRY
+	select SUPPORT_SPL
+	help
+	  Support for Kontron SMARC-sAL28 board.
+

config TARGET_COLIBRI_PXA270
bool "Support colibri_pxa270"
select CPU_PXA

arch/arm/Kconfig +0 -0
@@ -1904,6 +1913,7 @@ source "board/hisilicon/hikey/Kconfig"

source "board/hisilicon/hikey960/Kconfig"
source "board/hisilicon/poplar/Kconfig"
source "board/isee/igep003x/Kconfig"
+source "board/kontron/sl28/Kconfig"
source "board/phytec/pcm051/Kconfig"
source "board/silica/pengwyn/Kconfig"
source "board/spear/spear300/Kconfig"

arch/arm/dts/Makefile index renamed from arch/arm/dts/Makefile +0 -0

559d3ab6a7..7050ec72eb 100644

arch/arm/dts/Makefile +3 -0
@@ -379,6 +379,9 @@ dtb-$(CONFIG_FSL_LSCH3) += fsl-ls2080a-qds.dtb \
 	fsl-ls2088a-rdb-qspi.dtb \
 	fsl-ls1088a-rdb.dtb \
 	fsl-ls1088a-qds.dtb \
+	fsl-ls1028a-kontron-sl28.dtb \
+	fsl-ls1028a-kontron-sl28-var3.dtb \
+	fsl-ls1028a-kontron-sl28-var4.dtb \
 	fsl-ls1028a-rdb.dtb \
 	fsl-ls1028a-qds-duart.dtb \
 	fsl-ls1028a-qds-lpuart.dtb \
arch/arm/dts/fsl-ls1028a-kontron-sl28-var3.dts new file +12 -0
new file mode 100644
index 0000000000..23f89eadb3
@@ -0,0 +1,14 @@
+// SPDX-License-Identifier: GPL-2.0+
+/*
+ * Kontron SMARC-sAL28 device tree source (Single PHY version)  */
+
+/dts-v1/;
+
+#include "fsl-ls1028a-kontron-sl28.dts"
+
+/ {
+	u-boot,dm-pre-reloc;
+	model = "Kontron SMARC-sAL28 Board (Single PHY)";
+	compatible = "kontron,sl28-var3", "kontron,sl28", "fsl,ls1028a"; };
arch/arm/dts/fsl-ls1028a-kontron-sl28-var4.dts new file +40 -0
new file mode 100644
index 0000000000..8b51cf1207
@@ -0,0 +1,42 @@
+// SPDX-License-Identifier: GPL-2.0+
+/*
+ * Kontron SMARC-sAL28 device tree source (Dual PHY version)  */
+
+/dts-v1/;
+
+#include "fsl-ls1028a-kontron-sl28.dts"
+#include <dt-bindings/net/qca-ar803x.h>
+
+/ {
+	u-boot,dm-pre-reloc;
+	model = "Kontron SMARC-sAL28 Board (Dual PHY)";
+	compatible = "kontron,sl28-var4", "kontron,sl28", "fsl,ls1028a"; };
+
+&enetc1 {
+	status = "okay";
+	phy-mode = "rgmii-id";
+	phy-handle = <&phy1>;
+};
+
+&mdio0 {
+	phy1: phy at 4 {
+		reg = <4>;
+
+		qca,clk-out-frequency = <125000000>;
+		qca,clk-out-strength = <AR803X_STRENGTH_FULL>;
+
+		vddio-supply = <&vddh>;
+
+		vddio: vddio-regulator {
+			regulator-name = "VDDIO";
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+		};
+
+		vddh: vddh-regulator {
+			regulator-name = "VDDH";
+		};
+	};
+};
arch/arm/dts/fsl- renamed from arch/arm/dts/fsl-ls1028a-kontron-sl28.dts +0 -0

ls1028a-kontron-sl28.dts
new file mode 100644
index 0000000000..8d4c1102c4

arch/arm/dts/fsl-ls1028a-kontron-sl28.dts new file +127 -0
@@ -0,0 +1,128 @@
+// SPDX-License-Identifier: GPL-2.0+
+/*
+ * Kontron SMARC-sAL28 device tree source (base version)  */
+
+/dts-v1/;
+
+#include "fsl-ls1028a.dtsi"
+
+/ {
+	u-boot,dm-pre-reloc;
+	model = "Kontron SMARC-sAL28 Board";
+	compatible = "kontron,sl28", "fsl,ls1028a";
+
+	aliases {
+		serial0 = &serial0;
+		serial1 = &serial1;
+		spi0 = &fspi;
+		spi1 = &dspi2;
+		mmc0 = &esdhc0;
+		mmc1 = &esdhc1;
+		i2c0 = &i2c0;
+		i2c1 = &i2c3;
+		i2c2 = &i2c4;
+		rtc0 = &rtc;
+		ethernet0 = &enetc0;
+		ethernet1 = &enetc1;
+		ethernet2 = &enetc2;
+		ethernet3 = &enetc6;
+	};
+
+	chosen {
+		stdout-path = &serial0;
+	};
+};
+
+&dspi2 {
+	u-boot,dm-pre-reloc;
+	status = "okay";
+};
+
+&enetc0 {
+	status = "okay";
+	phy-mode = "sgmii";
+	phy-handle = <&phy0>;
+};
+
+&enetc1 {
+	status = "disabled";
+};
+
+&enetc2 {
+	status = "disabled";
+};
+
+&enetc6 {
+	status = "disabled";
+};
+
+&esdhc0 {
+	u-boot,dm-pre-reloc;
+	status = "okay";
+};
+
+&esdhc1 {
+	u-boot,dm-pre-reloc;
+	status = "okay";
+	bus-width = <8>;
+};
+
+&fspi {
+	u-boot,dm-pre-reloc;
+	status = "okay";
+
+	flash at 0 {
+		u-boot,dm-pre-reloc;
+		#address-cells = <1>;
+		#size-cells = <1>;
+		compatible = "jedec,spi-nor";
+		m25p,fast-read;
+		spi-max-frequency = <133000000>;
+		reg = <0>;
+		spi-rx-bus-width = <2>;
+		spi-tx-bus-width = <1>;
+	 };
+};
+
+&i2c0 {
+	status = "okay";
+
+	rtc: rtc at 32 {
+		compatible = "microcrystal,rv8803";
+		reg = <0x32>;
+	};
+};
+
+&i2c3 {
+	status = "okay";
+};
+
+&i2c4 {
+	status = "okay";
+};
+
+&mdio0 {
+	status = "okay";
+
+	phy0: phy at 5 {
+		reg = <5>;
+	};
+};
+
+&serial0 {
+	u-boot,dm-pre-reloc;
+	status = "okay";
+};
+
+&sysclk {
+	u-boot,dm-pre-reloc;
+};
+
+&usb1 {
+	status = "okay";
+};
+
+&usb2 {
+	status = "okay";
+};
board/kontron/sl28/Kconfig new file renamed from board/kontron/sl28/Kconfig +0 -0

mode 100644 index 0000000000..cdec39be01

board/kontron/sl28/Kconfig new file +18 -0
@@ -0,0 +1,18 @@
+if TARGET_SL28
+
+config SYS_BOARD
+	default "sl28"
+
+config SYS_VENDOR
+	default "kontron"
+
+config SYS_SOC
+	default "fsl-layerscape"
+
+config SYS_CONFIG_NAME
+	default "kontron_sl28"
+
+config SYS_TEXT_BASE
+	default 0x96000000
+
+endif
(quoted diff) +0 -0

b/board/kontron/sl28/MAINTAINERS new file mode 100644 index 0000000000..047a057646

board/kontron/sl28/MAINTAINERS new file +6 -0
@@ -0,0 +1,6 @@
+Kontron SMARC-sAL28 board
+M:	Michael Walle <[email protected]>
+S:	Maintained
+F:	board/kontron/sl28/
+F:	include/configs/kontron_sl28.h
+F:	configs/kontron_sl28_defconfig
board/kontron/sl28/Makefile new renamed from board/kontron/sl28/Makefile +0 -0

file mode 100644 index 0000000000..0f1866c874

board/kontron/sl28/Makefile new file +8 -0
@@ -0,0 +1,8 @@
+# SPDX-License-Identifier:	GPL-2.0+
+
+ifndef CONFIG_SPL_BUILD
+obj-y += sl28.o
+endif
+
+obj-y += common.o ddr.o
+obj-$(CONFIG_SPL_BUILD) += spl.o
board/kontron/sl28/README new renamed from board/kontron/sl28/README +0 -0

file mode 100644 index 0000000000..931563f299

board/kontron/sl28/README new file +63 -0
@@ -0,0 +1,63 @@
+Summary
+=======
+
+The Kontron SMARC-sAL28 board is a TSN-enabled dual-core ARM A72
+processor module with an on-chip 6-port TSN switch and a 3D GPU.
+
+
+Quickstart
+==========
+
+Compile U-Boot
+--------------
+
+ $ make kontron_sl28_defconfig
+ $ CROSS_COMPILE=aarch64-linux-gnu make
+
+Copy u-boot-with-spl.bin to a TFTP server.
+
+Install the bootloader on the board
+-----------------------------------
+
+Please note, this bootloader doesn't support the builtin watchdog
+(yet), therefore you have to disable it, see below. Otherwise you'll
+end up in the failsafe bootloader on every reset.
+
+ > tftp path/to/u-boot-with-spl.bin
+ > sf probe 0
+ > sf update $fileaddr 0x210000 $filesize
+
+The board is fully failsafe, you can't break anything. But since you've
+disabled the builtin watchdog you might have to manually enter failsafe
+mode by asserting the FORCE_RECOV# line during board reset.
+
+Disable the builtin watchdog
+----------------------------
+
+ - boot into the failsafe bootloader, either by asserting the
+   FORCE_RECOV# line or if you still have the original bootloader
+   installed you can use the command "wdt dev cpld_watchdog at 4a; wdt
+   expire 1"
+ - in the failsafe bootloader use the "sl28 nvm" command to disable
+   the automatic start of the builtin watchdog:
+   > sl28 nvm 0008
+ - power-cycle the board
+
+
+Useful I2C tricks
+=================
+
+The board has a board management controller which is not supported in
+u-boot (yet). But you can use the i2c command to access it:
+
+ # reset into failsafe bootloader
+ > i2c mw 4a 5.1 0; i2c mw 4a 6.1 6b; i2c mw 4a 4.1 42
+
+ # read board management controller version
+ > i2c md 4a 3.1 1
+
+
+Vendor Documentation
+====================
+
+https://raw.githubusercontent.com/kontron/u-boot-smarc-

sal28/master/boa

board/kontron/sl28/README new file +1 -0
+rd/kontron/sl28/README.md
board/kontron/sl28/common.c new file +10 -0
new file mode 100644 index 0000000000..14704f7051
@@ -0,0 +1,10 @@
+// SPDX-License-Identifier: GPL-2.0+
+
+#include <common.h>
+#include <asm/arch-fsl-layerscape/soc.h>
+
+int board_early_init_f(void)
+{
+	fsl_lsch3_early_init_f();
+	return 0;
+}
board/kontron/sl28/ddr.c new file renamed from board/kontron/sl28/ddr.c +0 -0

mode 100644 index 0000000000..110f57ac90

board/kontron/sl28/ddr.c new file +97 -0
@@ -0,0 +1,98 @@
+// SPDX-License-Identifier: GPL-2.0+
+
+#include <common.h>
+#include <asm/io.h>
+#include <fsl_ddr_sdram.h>
+
+DECLARE_GLOBAL_DATA_PTR;
+
+#define DCFG_GPPORCR1 0x20
+
+#define GPPORCR1_MEM_MASK		(0x7 << 5)
+#define GPPORCR1_MEM_512MB_CS0		(0x0 << 5)
+#define GPPORCR1_MEM_1GB_CS0		(0x1 << 5)
+#define GPPORCR1_MEM_2GB_CS0		(0x2 << 5)
+#define GPPORCR1_MEM_4GB_CS0_1		(0x3 << 5)
+#define GPPORCR1_MEM_4GB_CS0_2		(0x4 << 5)
+#define GPPORCR1_MEM_8GB_CS0_1_2_3	(0x5 << 5)
+#define GPPORCR1_MEM_8GB_CS0_1		(0x6 << 5)
+
+static fsl_ddr_cfg_regs_t __maybe_unused ddr_cfg_regs = {
+	.cs[0].bnds		= 0x0000007f,
+	.cs[0].config		= 0x80044402,
+	.cs[1].bnds		= 0x008000ff,
+	.cs[1].config		= 0x80004402,
+
+	.timing_cfg_0		= 0x9011010c,
+	.timing_cfg_3		= 0x010c1000,
+	.timing_cfg_1		= 0xbcb48c66,
+	.timing_cfg_2		= 0x0fc0d118,
+	.ddr_sdram_cfg		= 0xe70c000c,
+	.ddr_sdram_cfg_2	= 0x24401111,
+	.ddr_sdram_mode		= 0x00441c70,
+	.ddr_sdram_mode_3	= 0x00001c70,
+	.ddr_sdram_mode_5	= 0x00001c70,
+	.ddr_sdram_mode_7	= 0x00001c70,
+	.ddr_sdram_mode_2	= 0x00180000,
+	.ddr_sdram_mode_4	= 0x00180000,
+	.ddr_sdram_mode_6	= 0x00180000,
+	.ddr_sdram_mode_8	= 0x00180000,
+
+	.ddr_sdram_interval	= 0x0c30030c,
+	.ddr_data_init		= 0xdeadbeef,
+
+	.ddr_sdram_clk_cntl	= 0x02400000,
+
+	.timing_cfg_4		= 0x00000001,
+	.timing_cfg_5		= 0x04401400,
+
+	.ddr_zq_cntl		= 0x89080600,
+	.ddr_wrlvl_cntl		= 0x8675f606,
+	.ddr_wrlvl_cntl_2	= 0x04080700,
+	.ddr_wrlvl_cntl_3	= 0x00000009,
+
+	.ddr_cdr1		= 0x80040000,
+	.ddr_cdr2		= 0x0000bc01,
+};
+
+int fsl_initdram(void)
+{
+	u32 gpporcr1 = in_le32(DCFG_BASE + DCFG_GPPORCR1);
+	phys_size_t dram_size;
+
+	switch (gpporcr1 & GPPORCR1_MEM_MASK) {
+	case GPPORCR1_MEM_2GB_CS0:
+		dram_size = 0x80000000;
+		ddr_cfg_regs.cs[1].bnds = 0;
+		ddr_cfg_regs.cs[1].config = 0;
+		ddr_cfg_regs.cs[1].config_2 = 0;
+		break;
+	case GPPORCR1_MEM_4GB_CS0_1:
+		dram_size = 0x100000000ULL;
+		break;
+	case GPPORCR1_MEM_512MB_CS0:
+		dram_size = 0x20000000;
+		/* fall through for now */
+	case GPPORCR1_MEM_1GB_CS0:
+		dram_size = 0x40000000;
+		/* fall through for now */
+	case GPPORCR1_MEM_4GB_CS0_2:
+		dram_size = 0x100000000ULL;
+		/* fall through for now */
+	case GPPORCR1_MEM_8GB_CS0_1:
+	case GPPORCR1_MEM_8GB_CS0_1_2_3:
+		dram_size = 0x200000000ULL;
+		/* fall through for now */
+	default:
+		panic("Unsupported memory configuration (%08x)\n",
+		      gpporcr1 & GPPORCR1_MEM_MASK);
+		break;
+	}
+
+#if !defined(CONFIG_SPL) || defined(CONFIG_SPL_BUILD)
+	fsl_ddr_set_memctl_regs(&ddr_cfg_regs, 0, 0); #endif
+	gd->ram_size = dram_size;
+
+	return 0;
+}
board/kontron/sl28/sl28.c new file renamed from board/kontron/sl28/sl28.c +0 -0

mode 100644 index 0000000000..ef35541c86

board/kontron/sl28/sl28.c new file +28 -0
@@ -0,0 +1,92 @@
+// SPDX-License-Identifier: GPL-2.0+
+
+#include <common.h>
+#include <malloc.h>
+#include <errno.h>
+#include <fsl_ddr.h>
+#include <asm/io.h>
+#include <fdt_support.h>
+#include <linux/libfdt.h>
+#include <env_internal.h>
+#include <asm/arch-fsl-layerscape/soc.h> #include
+<asm/arch-fsl-layerscape/fsl_icid.h>
+#include <i2c.h>
+#include <asm/arch/soc.h>
+#include <fsl_immap.h>
+#include <netdev.h>
+
+#include <fdtdec.h>
+#include <miiphy.h>
+
+#define DCFG_RCWSR25 0x160
+#define GPINFO_HW_VARIANT_MASK 0xff
+
+DECLARE_GLOBAL_DATA_PTR;
+
+int sl28_variant(void)
+{
+	return in_le32(DCFG_BASE + DCFG_RCWSR25) &

GPINFO_HW_VARIANT_MASK; }

board/kontron/sl28/sl28.c new file +60 -0
+
+int board_fit_config_name_match(const char *name) {
+	int variant = sl28_variant();
+
+	switch (variant) {
+	case 3:
+		return strcmp(name, "fsl-ls1028a-kontron-sl28-var3");
+	case 4:
+		return strcmp(name, "fsl-ls1028a-kontron-sl28-var4");
+	default:
+		return strcmp(name, "fsl-ls1028a-kontron-sl28");
+	}
+}
+
+int board_init(void)
+{
+#ifdef CONFIG_ENV_IS_NOWHERE
+	gd->env_addr = (ulong)&default_environment[0]; #endif
+
+#ifndef CONFIG_SYS_EARLY_PCI_INIT
+	pci_init();
+#endif
+
+	return 0;
+}
+
+int board_eth_init(bd_t *bis)
+{
+	return pci_eth_init(bis);
+}
+
+void detail_board_ddr_info(void)
+{
+	puts("\nDDR    ");
+	print_size(gd->bd->bi_dram[0].size + gd->bd->bi_dram[1].size, "");
+	print_ddr_info(0);
+}
+
+#ifdef CONFIG_OF_BOARD_SETUP
+int ft_board_setup(void *blob, bd_t *bd) {
+	u64 base[CONFIG_NR_DRAM_BANKS];
+	u64 size[CONFIG_NR_DRAM_BANKS];
+	int nbanks = CONFIG_NR_DRAM_BANKS;
+	int i;
+
+	ft_cpu_setup(blob, bd);
+
+	/* fixup DT for the two GPP DDR banks */
+	for (i = 0; i < nbanks; i++) {
+		base[i] = gd->bd->bi_dram[i].start;
+		size[i] = gd->bd->bi_dram[i].size;
+	}
+
+	fdt_fixup_memory_banks(blob, base, size, nbanks);
+
+	fdt_fixup_icid(blob);
+
+	return 0;
+}
+#endif
board/kontron/sl28/spl.c new file renamed from board/kontron/sl28/spl.c +0 -0

mode 100644 index 0000000000..eb6d2dc909

board/kontron/sl28/spl.c new file +8 -0
@@ -0,0 +1,9 @@
+// SPDX-License-Identifier: GPL-2.0+
+
+#include <common.h>
+#include <asm/spl.h>
+
+void board_boot_order(u32 *spl_boot_list) {
+	spl_boot_list[0] = BOOT_DEVICE_SPI;
+}
configs/kontron_sl28_defconfig new file +32 -0
new file mode 100644 index 0000000000..14bff90249
@@ -0,0 +1,102 @@
+CONFIG_ARM=y
+CONFIG_TARGET_SL28=y
+CONFIG_SPL_LIBCOMMON_SUPPORT=y
+CONFIG_SPL_LIBGENERIC_SUPPORT=y
+CONFIG_SYS_MALLOC_F_LEN=0x4000
+CONFIG_ENV_SIZE=0x2000
+CONFIG_ENV_OFFSET=0x3e0000
+CONFIG_ENV_SECT_SIZE=0x10000
+CONFIG_SYS_SPI_U_BOOT_OFFS=0x230000
+CONFIG_DM_GPIO=y
+CONFIG_SYS_FSL_SDHC_CLK_DIV=1
+CONFIG_SPL_SERIAL_SUPPORT=y
+CONFIG_NR_DRAM_BANKS=2
+CONFIG_SPL_SIZE_LIMIT=0x20000
+CONFIG_SPL_SIZE_LIMIT_PROVIDE_STACK=0x0
+CONFIG_SPL=y
+CONFIG_ENV_OFFSET_REDUND=0x3f0000
+CONFIG_SPL_SPI_FLASH_SUPPORT=y
+CONFIG_SPL_SPI_SUPPORT=y
+# CONFIG_PSCI_RESET is not set
+CONFIG_SPL_TEXT_BASE=0x18010000
+CONFIG_AHCI=y
+CONFIG_DISTRO_DEFAULTS=y
+CONFIG_FIT=y
+CONFIG_FIT_VERBOSE=y
+CONFIG_OF_BOARD_SETUP=y
+CONFIG_OF_STDOUT_VIA_ALIAS=y
+CONFIG_BOOTDELAY=10
+CONFIG_USE_BOOTARGS=y
+CONFIG_BOARD_LATE_INIT=y
+CONFIG_SPL_BOARD_INIT=y
+# CONFIG_SPL_LEGACY_IMAGE_SUPPORT is not set

CONFIG_SPL_SEPARATE_BSS=y

configs/kontron_sl28_defconfig new file +17 -0
+CONFIG_SPL_MPC8XXX_INIT_DDR_SUPPORT=y
+CONFIG_SPL_SPI_LOAD=y
+CONFIG_CMD_ASKENV=y
+CONFIG_CMD_GREPENV=y
+CONFIG_CMD_DM=y
+CONFIG_CMD_GPT=y
+CONFIG_CMD_I2C=y
+CONFIG_CMD_MMC=y
+CONFIG_CMD_PCI=y
+CONFIG_CMD_USB=y
+CONFIG_CMD_WDT=y
+CONFIG_CMD_CACHE=y
+CONFIG_MP=y
+CONFIG_OF_CONTROL=y
+CONFIG_SPL_OF_CONTROL=y
+CONFIG_DEFAULT_DEVICE_TREE="fsl-ls1028a-kontron-sl28"
+CONFIG_OF_LIST="fsl-ls1028a-kontron-sl28 fsl-ls1028a-kontron-sl28-var3 fsl-

ls1028a-kontron-sl28-var4"

configs/kontron_sl28_defconfig new file +21 -0
+CONFIG_MULTI_DTB_FIT=y
+CONFIG_ENV_IS_IN_SPI_FLASH=y
+CONFIG_SYS_REDUNDAND_ENVIRONMENT=y
+CONFIG_NET_RANDOM_ETHADDR=y
+CONFIG_NETCONSOLE=y
+CONFIG_DM=y
+CONFIG_SPL_DM=y
+CONFIG_SPL_DM_SEQ_ALIAS=y
+CONFIG_SCSI_AHCI=y
+CONFIG_FSL_CAAM=y
+CONFIG_SYS_FSL_DDR3=y
+CONFIG_DM_I2C=y
+CONFIG_I2C_SET_DEFAULT_BUS_NUM=y
+CONFIG_I2C_DEFAULT_BUS_NUMBER=0
+CONFIG_I2C_MUX=y
+CONFIG_DM_MMC=y
+CONFIG_FSL_ESDHC=y
+CONFIG_DM_SPI_FLASH=y
+CONFIG_SPI_FLASH_WINBOND=y
+# CONFIG_SPI_FLASH_USE_4K_SECTORS is not set CONFIG_PHYLIB=y
+CONFIG_PHY_ATHEROS=y CONFIG_DM_ETH=y CONFIG_DM_MDIO=y

CONFIG_PHY_GIGE=y

configs/kontron_sl28_defconfig new file +2 -0
+CONFIG_E1000=y CONFIG_FSL_ENETC=y CONFIG_NVME=y CONFIG_PCI=y
+CONFIG_DM_PCI=y CONFIG_DM_PCI_COMPAT=y

CONFIG_PCIE_ECAM_GENERIC=y

configs/kontron_sl28_defconfig new file +4 -0
+CONFIG_PCIE_LAYERSCAPE=y CONFIG_DM_RTC=y CONFIG_RTC_RV8803=y
+CONFIG_SCSI=y CONFIG_DM_SCSI=y CONFIG_SYS_NS16550=y CONFIG_SPI=y
+CONFIG_DM_SPI=y CONFIG_FSL_DSPI=y CONFIG_NXP_FSPI=y CONFIG_USB=y
+CONFIG_DM_USB=y # CONFIG_SPL_DM_USB is not set

CONFIG_USB_XHCI_HCD=y

configs/kontron_sl28_defconfig new file +4 -0
+CONFIG_USB_XHCI_DWC3=y CONFIG_WDT=y CONFIG_WDT_SP805=y
+CONFIG_OF_LIBFDT_ASSUME_MASK=0x0
+CONFIG_OF_LIBFDT_OVERLAY=y
+CONFIG_EFI_LOADER_BOUNCE_BUFFER=y
include/configs/kontron_sl28.h new file +23 -0
new file mode 100644 index 0000000000..3711f8b744
@@ -0,0 +1,119 @@
+/* SPDX-License-Identifier: GPL-2.0+ */
+
+#ifndef __SL28_H
+#define __SL28_H
+
+#include <asm/arch/stream_id_lsch3.h>
+#include <asm/arch/config.h>
+#include <asm/arch/soc.h>
+
+/* We don't use hwconfig but this has to be defined.. */ #define
+HWCONFIG_BUFFER_SIZE 256
+
+/* DDR */
+#define CONFIG_DDR_ECC
+#define CONFIG_ECC_INIT_VIA_DDRCONTROLLER
+#define CONFIG_MEM_INIT_VALUE		0xdeadbeef
+
+#define CONFIG_VERY_BIG_RAM
+#define CONFIG_CHIP_SELECTS_PER_CTRL	4
+#define CONFIG_DIMM_SLOTS_PER_CTLR	1
+#define CONFIG_SYS_DDR_SDRAM_BASE	0x80000000UL
+#define CONFIG_SYS_FSL_DDR_SDRAM_BASE_PHY	0
+#define CONFIG_SYS_SDRAM_BASE

CONFIG_SYS_DDR_SDRAM_BASE

include/configs/kontron_sl28.h new file +5 -0
+#define CONFIG_SYS_DDR_BLOCK2_BASE	0x2080000000ULL
+#define CONFIG_SYS_FSL_DDR_MAIN_NUM_CTRLS	1
+
+/* early stack pointer */
+#define CONFIG_SYS_INIT_SP_ADDR
	(CONFIG_SYS_FSL_OCRAM_BASE + 0xeff0)
include/configs/kontron_sl28.h new file +13 -0
+
+/* memtest command */
+#define CONFIG_SYS_MEMTEST_START        0x80000000
+#define CONFIG_SYS_MEMTEST_END          0x9fffffff
+
+/* SMP */
+#define CPU_RELEASE_ADDR		secondary_boot_func
+
+/* generic timer */
+#define COUNTER_FREQUENCY		25000000
+
+/* size of malloc() pool */
+#define CONFIG_SYS_MALLOC_LEN		(CONFIG_ENV_SIZE + 2048 *

1024)

include/configs/kontron_sl28.h new file +3 -0
+
+/* early heap for SPL DM */
+#define CONFIG_MALLOC_F_ADDR

CONFIG_SYS_FSL_OCRAM_BASE

include/configs/kontron_sl28.h new file +6 -0
+
+/* serial port */
+#define CONFIG_SYS_NS16550_SERIAL
+#define CONFIG_SYS_NS16550_REG_SIZE 1
+#define CONFIG_SYS_NS16550_CLK          (get_bus_freq(0) / 2)
+#define CONFIG_SYS_BAUDRATE_TABLE	{ 9600, 19200, 38400, 57600,

115200 }

include/configs/kontron_sl28.h new file +19 -0
+
+#define CONFIG_SYS_CLK_FREQ		100000000
+#define CONFIG_DDR_CLK_FREQ		100000000
+#define COUNTER_FREQUENCY_REAL		(CONFIG_SYS_CLK_FREQ / 4)
+
+/* MMC */
+#ifdef CONFIG_MMC
+#define CONFIG_SYS_FSL_MMC_HAS_CAPBLT_VS33
+#endif
+
+/* ethernet */
+#define CONFIG_SYS_RX_ETH_BUFFER	8
+
+#ifdef CONFIG_SPL
+#define CONFIG_SPL_TARGET		"u-boot-with-spl.bin"
+#define CONFIG_SPL_BSS_START_ADDR	0x80100000
+#define CONFIG_SPL_BSS_MAX_SIZE		0x00100000
+#define CONFIG_SPL_MAX_SIZE		0x20000
+#define CONFIG_SPL_STACK		(CONFIG_SYS_FSL_OCRAM_BASE +

0x9ff0)

include/configs/kontron_sl28.h new file +5 -0
+
+#define CONFIG_SYS_SPL_MALLOC_SIZE	0x00100000
+#define CONFIG_SYS_SPL_MALLOC_START	0x80200000
+#define CONFIG_SYS_MONITOR_LEN		(1024 * 1024)
+#define CONFIG_SYS_SPI_U_BOOT_SIZE	(0x100000 -

(CONFIG_SYS_SPI_U_BOOT_OFFS)

include/configs/kontron_sl28.h new file +9 -0
+#endif
+
+#ifdef CONFIG_SPL_BUILD
+#define CONFIG_SYS_MONITOR_BASE		CONFIG_SPL_TEXT_BASE
+#else
+#define CONFIG_SYS_MONITOR_BASE		CONFIG_SYS_TEXT_BASE
+#endif
+
+#define CONFIG_SYS_LOAD_ADDR
	(CONFIG_SYS_DDR_SDRAM_BASE + 0x10000000)
include/configs/kontron_sl28.h new file +36 -1
+
+/* environment */
+/* allow to overwrite serial and ethaddr */ #define
+CONFIG_ENV_OVERWRITE
+
+#define CONFIG_LOADADDR 0x81000000
+#define ENV_MEM_LAYOUT_SETTINGS \
+	"scriptaddr=0x90000000\0" \
+	"pxefile_addr_r=0x90100000\0" \
+	"kernel_addr_r=" __stringify(CONFIG_LOADADDR) "\0" \
+	"fdt_addr_r=0x83000000\0" \
+	"ramdisk_addr_r=0x83100000\0"
+
+#ifndef CONFIG_SPL_BUILD
+#define BOOT_TARGET_DEVICES(func) \
+	func(MMC, mmc, 1) \
+	func(MMC, mmc, 0) \
+	func(NVME, nvme, 0) \
+	func(USB, usb, 0) \
+	func(DHCP, dhcp, 0) \
+	func(PXE, pxe, 0)
+#include <config_distro_bootcmd.h>
+#else
+#define BOOTENV
+#endif
+
+#define CONFIG_EXTRA_ENV_SETTINGS \
+	"fdt_high=0xffffffffffffffff\0" \
+	"initrd_high=0xffffffffffffffff\0" \
+	"env_addr=0x203e0004\0" \
+	"envload=env import -d -b ${env_addr}\0" \
+	"install_rcw=source 20200000\0" \
+	ENV_MEM_LAYOUT_SETTINGS \
+	BOOTENV
+
+#endif /* __SL28_H */
--
Quoted 1 line

2.20.1

Kindly fix below build error:

board/kontron/sl28/sl28.c: In function 'board_init':
+board/kontron/sl28/sl28.c:52:2: error: implicit declaration of function 'pci_init'; did you mean 'phy_init'? [-Werror=implicit-function-declaration]

+   52 |  pci_init();
+      |  ^~~~~~~~
+      |  phy_init
+board/kontron/sl28/sl28.c: At top level:
+board/kontron/sl28/sl28.c:58:20: error: unknown type name 'bd_t'; did you mean 'gd_t'?
+   58 | int board_eth_init(bd_t *bis)
+      |                    ^~~~
+      |                    gd_t
+board/kontron/sl28/sl28.c:71:32: error: unknown type name 'bd_t'; did you mean 'gd_t'?
+   71 | int ft_board_setup(void *blob, bd_t *bd)
+      |                                ^~~~
+      |                                gd_t

+cc1: all warnings being treated as errors
+make[2]: *** [board/kontron/sl28/sl28.o] Error 1
+make[1]: *** [board/kontron/sl28] Error 2
+make: *** [sub-make] Error 2

Regards
Priyanka

#4 lore raw

v3 cover Basic Kontron SMARC-sAL28 board support

In reply to Michael Walle

Am 2020-05-10 01:20, schrieb Michael Walle:

Quoted 4 lines

Add basic board support for the Kontron SMARC-sAL28 board. Please note, that this board doesn't support TF-a (yet). Therefore, the u-boot SPL is
the first code which is run and it has to set up the RAM.

ping? :)

Quoted 45 lines

changes since v3:
- add variant 4 support. Since the atheros PHY dt bindings were merged into master, we can now use them
- add environment section in include/configs/kontron_sl28.h
- add cover letter

changes since v1:
- fix watchdog device tree reference

Michael Walle (2):
armv8: ls1028a: move FSL_LAYERSCAPE to kconfig
board: kontron: add sl28 support

 arch/arm/Kconfig                              |  10 ++
 arch/arm/cpu/armv8/fsl-layerscape/Kconfig     |   1 +
 arch/arm/dts/Makefile                         |   3 +
 .../arm/dts/fsl-ls1028a-kontron-sl28-var3.dts |  14 ++
 .../arm/dts/fsl-ls1028a-kontron-sl28-var4.dts |  42 ++++++
 arch/arm/dts/fsl-ls1028a-kontron-sl28.dts     | 128 ++++++++++++++++++
 board/kontron/sl28/Kconfig                    |  18 +++
 board/kontron/sl28/MAINTAINERS                |   6 +
 board/kontron/sl28/Makefile                   |   8 ++
 board/kontron/sl28/README                     |  63 +++++++++
 board/kontron/sl28/common.c                   |  10 ++
 board/kontron/sl28/ddr.c                      |  98 ++++++++++++++
 board/kontron/sl28/sl28.c                     |  92 +++++++++++++
 board/kontron/sl28/spl.c                      |   9 ++
 configs/kontron_sl28_defconfig                | 102 ++++++++++++++
 include/configs/kontron_sl28.h                | 119 ++++++++++++++++
 include/configs/ls1028a_common.h              |   1 -
 17 files changed, 723 insertions(+), 1 deletion(-)
 create mode 100644 arch/arm/dts/fsl-ls1028a-kontron-sl28-var3.dts
 create mode 100644 arch/arm/dts/fsl-ls1028a-kontron-sl28-var4.dts
 create mode 100644 arch/arm/dts/fsl-ls1028a-kontron-sl28.dts
 create mode 100644 board/kontron/sl28/Kconfig
 create mode 100644 board/kontron/sl28/MAINTAINERS
 create mode 100644 board/kontron/sl28/Makefile
 create mode 100644 board/kontron/sl28/README
 create mode 100644 board/kontron/sl28/common.c
 create mode 100644 board/kontron/sl28/ddr.c
 create mode 100644 board/kontron/sl28/sl28.c
 create mode 100644 board/kontron/sl28/spl.c
 create mode 100644 configs/kontron_sl28_defconfig
 create mode 100644 include/configs/kontron_sl28.h
Signature · 1 line
-michael
#5 lore raw

v3 cover Basic Kontron SMARC-sAL28 board support

In reply to Michael Walle

[+CC some more as suggested by Marek]

Am 2020-05-10 01:20, schrieb Michael Walle:

Quoted 11 lines

Add basic board support for the Kontron SMARC-sAL28 board. Please note, that this board doesn't support TF-a (yet). Therefore, the u-boot SPL is
the first code which is run and it has to set up the RAM.

changes since v3:
- add variant 4 support. Since the atheros PHY dt bindings were merged into master, we can now use them
- add environment section in include/configs/kontron_sl28.h
- add cover letter

Quoted 6 lines

changes since v1:
- fix watchdog device tree reference

Michael Walle (2):
armv8: ls1028a: move FSL_LAYERSCAPE to kconfig
board: kontron: add sl28 support

ping :)

-michael