Add Rockchip RK3399 USB3.0 Host support
Subsystems (7)
v4 cover Add Rockchip RK3399 USB3.0 Host support
This series add quirks for DWC3 and add Rockchip RK3399 USB3.0 host support.
The function has been tested pass on rk3399-evb and roc-rk3399-pc board.
For V4 update:
- Collect Jagan's all fixed patches [1].
- Amend specific u-boot changes from dts to dtsi for [PATCH v3 6/7].
For V3 update:
- Fix compile error for [PATCH v2 1/9].
- Use Jagan's Type-C driver instead of [PATCH v2 5/9].
- Cleanup dts changes for [PATCH v2 7/9].
- Cleanup config changes for [PATCH v2 8/9] and [PATCH v2 9/9].
For V2 update:
- Amend type-c driver followed Jagan's comments for [PATCH 5/8].
- Fix dts commit for [PATCH 7/8].
- Split RK3399 default config for [PATCH 8/8].
- Add 'Reviewed-by' tag for [PATCH 1/8], [PATCH 2/8] and [PATCH 3/8].
[1] https://patchwork.ozlabs.org/project/uboot/cover/[email protected]
BR,
Frank
Frank Wang (7):
usb: dwc3: add dis_enblslpm_quirk
usb: dwc3: add dis_u2_freeclk_exists_quirk
usb: dwc3: amend UTMI/UTMIW phy interface setup
usb: dwc3: add make compatible for rockchip platform
driver: usb: drop legacy rockchip xhci driver
ARM: dts: rk3399-evb: usb3.0 host support
configs: evb-rk3399: update support usb3.0 host
Jagan Teki (9):
clk: rk3399: Enable/Disable the USB2PHY clk
clk: rk3399: Set empty for TCPHY assigned-clocks
clk: rk3399: Enable/Disable TCPHY clocks
phy: rockchip: Add Rockchip USB2PHY driver
arm64: dts: rk3399: Move u2phy into root port
phy: rockchip: Add Rockchip USB TypeC PHY driver
usb: dwc3: Add disable u2mac linestate check quirk
usb: dwc3: Enable AutoRetry feature in the controller
roc-rk3399-pc: Enable USB3.0 Host
arch/arm/dts/rk3399-evb-u-boot.dtsi | 13 + arch/arm/dts/rk3399.dtsi | 108 +-- configs/evb-rk3399_defconfig | 6 + configs/roc-pc-mezzanine-rk3399_defconfig | 5 + configs/roc-pc-rk3399_defconfig | 6 + drivers/Makefile | 1 + drivers/clk/rockchip/clk_rk3399.c | 38 + drivers/phy/Kconfig | 1 + drivers/phy/rockchip/Kconfig | 21 + drivers/phy/rockchip/Makefile | 7 + drivers/phy/rockchip/phy-rockchip-inno-usb2.c | 312 +++++++ drivers/phy/rockchip/phy-rockchip-typec.c | 796 ++++++++++++++++++ drivers/usb/common/common.c | 25 + drivers/usb/dwc3/core.c | 106 ++- drivers/usb/dwc3/core.h | 19 + drivers/usb/dwc3/dwc3-generic.c | 33 +- drivers/usb/host/Kconfig | 9 - drivers/usb/host/Makefile | 1 - drivers/usb/host/xhci-rockchip.c | 196 ----- include/dwc3-uboot.h | 3 + include/linux/usb/phy.h | 18 + 21 files changed, 1427 insertions(+), 297 deletions(-) create mode 100644 drivers/phy/rockchip/Kconfig create mode 100644 drivers/phy/rockchip/Makefile create mode 100644 drivers/phy/rockchip/phy-rockchip-inno-usb2.c create mode 100644 drivers/phy/rockchip/phy-rockchip-typec.c delete mode 100644 drivers/usb/host/xhci-rockchip.c
Signature · 1 line
2.17.1
PATCH v4 1/16 clk: rk3399: Enable/Disable the USB2PHY clk
From: Jagan Teki <[email protected]>
Enable/Disable the USB2PHY clk for rk3399.
CLK is clear in enable and set in disable functionality.
--- drivers/clk/rockchip/clk_rk3399.c | 12 ++++++++++++ 1 file changed, 12 insertions(+)
drivers/clk/rockchip/clk_rk3399.c +12 -0
@@ -1091,6 +1091,12 @@ static int rk3399_clk_enable(struct clk *clk)case SCLK_MACREF_OUT :rk_clrreg (&priv->cru->clkgate_con[5 ],BIT (6 ));break ; +case SCLK_USB2PHY0_REF : +rk_clrreg (&priv->cru->clkgate_con[6 ],BIT (5 )); +break ; +case SCLK_USB2PHY1_REF : +rk_clrreg (&priv->cru->clkgate_con[6 ],BIT (6 )); +break ;case ACLK_GMAC :rk_clrreg (&priv->cru->clkgate_con[32 ],BIT (0 ));break ;
@@ -1167,6 +1173,12 @@ static int rk3399_clk_disable(struct clk *clk)case SCLK_MACREF_OUT :rk_setreg (&priv->cru->clkgate_con[5 ],BIT (6 ));break ; +case SCLK_USB2PHY0_REF : +rk_setreg (&priv->cru->clkgate_con[6 ],BIT (5 )); +break ; +case SCLK_USB2PHY1_REF : +rk_setreg (&priv->cru->clkgate_con[6 ],BIT (6 )); +break ;case ACLK_GMAC :rk_setreg (&priv->cru->clkgate_con[32 ],BIT (0 ));break ;
Signature · 1 line
2.17.1
A message that is not in the archive (sent off-list or not yet received): 20200511075330.26462-1-frank.wang-TNX95d0MmH7DzftRWevZcw@public.gmane.org
PATCH v4 2/16 clk: rk3399: Set empty for TCPHY assigned-clocks
From: Jagan Teki <jagan-dyjBcgdgk7Pe9wHmmfpqLFaTQe2KTcn/@public.gmane.org>
Due to v5.7-rc1 sync the SD controller nodes in rk3399.dtsi have SCLK_UPHY0_TCPDCORE, SCLK_UPHY1_TCPDCORE assigned-clocks which are usually required for Linux and don't require to handle them in U-Boot.
assigned-clocks = <&cru SCLK_UPHY0_TCPDCORE>; assigned-clocks = <&cru SCLK_UPHY1_TCPDCORE>;
So, mark them as empty in clock otherwise device probe on those typec phy driver would fail.
--- drivers/clk/rockchip/clk_rk3399.c | 2 ++ 1 file changed, 2 insertions(+)
drivers/clk/rockchip/clk_rk3399.c +2 -0
@@ -997,6 +997,8 @@ static ulong rk3399_clk_set_rate(struct clk *clk, ulong rate)case ACLK_VOP1 :case HCLK_VOP1 :case HCLK_SD : +case SCLK_UPHY0_TCPDCORE : +case SCLK_UPHY1_TCPDCORE :/** * assigned-clocks handling won't require for vopl, so * return 0 to satisfy clk_set_defaults during device probe.
Signature · 1 line
2.17.1
PATCH v4 3/16 clk: rk3399: Enable/Disable TCPHY clocks
In reply to a message not in the archiveFrom: Jagan Teki <jagan-dyjBcgdgk7Pe9wHmmfpqLFaTQe2KTcn/@public.gmane.org>
Enable/Disable TCPHY clock for rk3399 platform.
--- drivers/clk/rockchip/clk_rk3399.c | 24 ++++++++++++++++++++++++ 1 file changed, 24 insertions(+)
drivers/clk/rockchip/clk_rk3399.c +24 -0
@@ -1144,6 +1144,18 @@ static int rk3399_clk_enable(struct clk *clk)case HCLK_HOST1_ARB :rk_clrreg (&priv->cru->clksel_con[20 ],BIT (8 ));break ; +case SCLK_UPHY0_TCPDPHY_REF : +rk_clrreg (&priv->cru->clkgate_con[13 ],BIT (4 )); +break ; +case SCLK_UPHY0_TCPDCORE : +rk_clrreg (&priv->cru->clkgate_con[13 ],BIT (5 )); +break ; +case SCLK_UPHY1_TCPDPHY_REF : +rk_clrreg (&priv->cru->clkgate_con[13 ],BIT (6 )); +break ; +case SCLK_UPHY1_TCPDCORE : +rk_clrreg (&priv->cru->clkgate_con[13 ],BIT (7 )); +break ;case SCLK_PCIEPHY_REF :rk_clrreg (&priv->cru->clksel_con[18 ],BIT (10 ));break ;
@@ -1226,6 +1238,18 @@ static int rk3399_clk_disable(struct clk *clk)case HCLK_HOST1_ARB :rk_setreg (&priv->cru->clksel_con[20 ],BIT (8 ));break ; +case SCLK_UPHY0_TCPDPHY_REF : +rk_setreg (&priv->cru->clkgate_con[13 ],BIT (4 )); +break ; +case SCLK_UPHY0_TCPDCORE : +rk_setreg (&priv->cru->clkgate_con[13 ],BIT (5 )); +break ; +case SCLK_UPHY1_TCPDPHY_REF : +rk_setreg (&priv->cru->clkgate_con[13 ],BIT (6 )); +break ; +case SCLK_UPHY1_TCPDCORE : +rk_setreg (&priv->cru->clkgate_con[13 ],BIT (7 )); +break ;case SCLK_PCIEPHY_REF :rk_clrreg (&priv->cru->clksel_con[18 ],BIT (10 ));break ;
Signature · 1 line
2.17.1
PATCH v4 4/16 phy: rockchip: Add Rockchip USB2PHY driver
In reply to a message not in the archiveFrom: Jagan Teki <jagan-dyjBcgdgk7Pe9wHmmfpqLFaTQe2KTcn/@public.gmane.org>
Add Rockchip USB2PHY driver with initial support.
This will help to use it for EHCI controller in host mode, and USB 3.0 controller in otg mode.
More functionality like charge, vbus detection will add it in future changes.
--- drivers/Makefile | 1 + drivers/phy/Kconfig | 1 + drivers/phy/rockchip/Kconfig | 14 + drivers/phy/rockchip/Makefile | 6 + drivers/phy/rockchip/phy-rockchip-inno-usb2.c | 312 ++++++++++++++++++ 5 files changed, 334 insertions(+) create mode 100644 drivers/phy/rockchip/Kconfig create mode 100644 drivers/phy/rockchip/Makefile create mode 100644 drivers/phy/rockchip/phy-rockchip-inno-usb2.c
drivers/Makefile +1 -0
@@ -91,6 +91,7 @@ obj-y += dfu/ obj-$(CONFIG_PCH) += pch/ obj-y += phy/allwinner/ obj-y += phy/marvell/ +obj-y += phy/rockchip/ obj-y += rtc/ obj-y += scsi/ obj-y += sound/
drivers/phy/Kconfig +1 -0
@@ -225,4 +225,5 @@ config PHY_MTK_TPHY multi-ports is first version, otherwise is second veriosn, so you can easily distinguish them by banks layout. +source "drivers/phy/rockchip/Kconfig" endmenu
drivers/phy/rockchip/Kconfig new file +14 -0
@@ -0,0 +1,14 @@ +# +# Phy drivers for Rockchip platforms +# + +menu "Rockchip PHY driver" + +config PHY_ROCKCHIP_INNO_USB2 + bool "Rockchip INNO USB2PHY Driver" + depends on ARCH_ROCKCHIP + select PHY + help + Support for Rockchip USB2.0 PHY with Innosilicon IP block. + +endmenu
drivers/phy/rockchip/Makefile new file +6 -0
@@ -0,0 +1,6 @@ +# SPDX-License-Identifier: GPL-2.0+ +# +# Copyright (C) 2020 Amarula Solutions(India) +# + +obj-$(CONFIG_PHY_ROCKCHIP_INNO_USB2) += phy-rockchip-inno-usb2.o
drivers/phy/rockchip/phy-rockchip-inno-usb2.c new file +312 -0
312 lines not on this page · raw message
Signature · 1 line
2.17.1
PATCH v4 5/16 arm64: dts: rk3399: Move u2phy into root port
In reply to a message not in the archiveFrom: Jagan Teki <jagan-dyjBcgdgk7Pe9wHmmfpqLFaTQe2KTcn/@public.gmane.org>
Yes, This is changing the actual device tree u2phy structure but the problem with the current Generic PHY subsystem is unable to find PHY if the PHY node is not part of the root structure.
This will be reverted,
- Once we support the PHY subsystem to get the PHY even though it is not part of the root node or
- any other relevant solution that get the phy directly without traversing all nodes.
--- arch/arm/dts/rk3399.dtsi | 108 +++++++++++++++++++-------------------- 1 file changed, 54 insertions(+), 54 deletions(-)
arch/arm/dts/rk3399.dtsi +54 -54
@@ -1387,60 +1387,6 @@ status = "disabled"; }; - u2phy0: usb2-phy@e450 { - compatible = "rockchip,rk3399-usb2phy"; - reg = <0xe450 0x10>; - clocks = <&cru SCLK_USB2PHY0_REF>; - clock-names = "phyclk"; - #clock-cells = <0>; - clock-output-names = "clk_usbphy0_480m"; - status = "disabled"; - - u2phy0_host: host-port { - #phy-cells = <0>; - interrupts = <GIC_SPI 27 IRQ_TYPE_LEVEL_HIGH 0>; - interrupt-names = "linestate"; - status = "disabled"; - }; - - u2phy0_otg: otg-port { - #phy-cells = <0>; - interrupts = <GIC_SPI 103 IRQ_TYPE_LEVEL_HIGH 0>, - <GIC_SPI 104 IRQ_TYPE_LEVEL_HIGH 0>, - <GIC_SPI 106 IRQ_TYPE_LEVEL_HIGH 0>; - interrupt-names = "otg-bvalid", "otg-id", - "linestate"; - status = "disabled"; - }; - }; - - u2phy1: usb2-phy@e460 { - compatible = "rockchip,rk3399-usb2phy"; - reg = <0xe460 0x10>; - clocks = <&cru SCLK_USB2PHY1_REF>; - clock-names = "phyclk"; - #clock-cells = <0>; - clock-output-names = "clk_usbphy1_480m"; - status = "disabled"; - - u2phy1_host: host-port { - #phy-cells = <0>; - interrupts = <GIC_SPI 31 IRQ_TYPE_LEVEL_HIGH 0>; - interrupt-names = "linestate"; - status = "disabled"; - }; - - u2phy1_otg: otg-port { - #phy-cells = <0>; - interrupts = <GIC_SPI 108 IRQ_TYPE_LEVEL_HIGH 0>, - <GIC_SPI 109 IRQ_TYPE_LEVEL_HIGH 0>, - <GIC_SPI 111 IRQ_TYPE_LEVEL_HIGH 0>; - interrupt-names = "otg-bvalid", "otg-id", - "linestate"; - status = "disabled"; - }; - }; - emmc_phy: phy@f780 { compatible = "rockchip,rk3399-emmc-phy"; reg = <0xf780 0x24>;
@@ -1462,6 +1408,60 @@ }; }; + u2phy0: usb2-phy@e450 { + compatible = "rockchip,rk3399-usb2phy"; + reg = <0x0 0xe450 0x0 0x10>; + clocks = <&cru SCLK_USB2PHY0_REF>; + clock-names = "phyclk"; + #clock-cells = <0>; + clock-output-names = "clk_usbphy0_480m"; + status = "disabled"; + + u2phy0_host: host-port { + #phy-cells = <0>; + interrupts = <GIC_SPI 27 IRQ_TYPE_LEVEL_HIGH 0>; + interrupt-names = "linestate"; + status = "disabled"; + }; + + u2phy0_otg: otg-port { + #phy-cells = <0>; + interrupts = <GIC_SPI 103 IRQ_TYPE_LEVEL_HIGH 0>, + <GIC_SPI 104 IRQ_TYPE_LEVEL_HIGH 0>, + <GIC_SPI 106 IRQ_TYPE_LEVEL_HIGH 0>; + interrupt-names = "otg-bvalid", "otg-id", + "linestate"; + status = "disabled"; + }; + }; + + u2phy1: usb2-phy@e460 { + compatible = "rockchip,rk3399-usb2phy"; + reg = <0x0 0xe460 0x0 0x10>; + clocks = <&cru SCLK_USB2PHY1_REF>; + clock-names = "phyclk"; + #clock-cells = <0>; + clock-output-names = "clk_usbphy1_480m"; + status = "disabled"; + + u2phy1_host: host-port { + #phy-cells = <0>; + interrupts = <GIC_SPI 31 IRQ_TYPE_LEVEL_HIGH 0>; + interrupt-names = "linestate"; + status = "disabled"; + }; + + u2phy1_otg: otg-port { + #phy-cells = <0>; + interrupts = <GIC_SPI 108 IRQ_TYPE_LEVEL_HIGH 0>, + <GIC_SPI 109 IRQ_TYPE_LEVEL_HIGH 0>, + <GIC_SPI 111 IRQ_TYPE_LEVEL_HIGH 0>; + interrupt-names = "otg-bvalid", "otg-id", + "linestate"; + status = "disabled"; + }; + }; + tcphy0: phy@ff7c0000 { compatible = "rockchip,rk3399-typec-phy"; reg = <0x0 0xff7c0000 0x0 0x40000>;
Signature · 1 line
2.17.1
A message that is not in the archive (sent off-list or not yet received): 20200511075520.26557-1-frank.wang-TNX95d0MmH7DzftRWevZcw@public.gmane.org
PATCH v4 6/16 phy: rockchip: Add Rockchip USB TypeC PHY driver
From: Jagan Teki <jagan-dyjBcgdgk7Pe9wHmmfpqLFaTQe2KTcn/@public.gmane.org>
Add USB TYPEC PHY driver for rockchip platform.
Referenced from Linux TypeC PHY driver, currently
supporting usb3-port and dp-port need to add it
in the future.
--- drivers/phy/rockchip/Kconfig | 7 + drivers/phy/rockchip/Makefile | 1 + drivers/phy/rockchip/phy-rockchip-typec.c | 796 ++++++++++++++++++++++ 3 files changed, 804 insertions(+) create mode 100644 drivers/phy/rockchip/phy-rockchip-typec.c
drivers/phy/rockchip/Kconfig +7 -0
@@ -11,4 +11,11 @@ config PHY_ROCKCHIP_INNO_USB2 help Support for Rockchip USB2.0 PHY with Innosilicon IP block. +config PHY_ROCKCHIP_TYPEC + bool "Rockchip TYPEC PHY Driver" + depends on ARCH_ROCKCHIP + select PHY + help + Enable this to support the Rockchip USB TYPEC PHY. + endmenu
drivers/phy/rockchip/Makefile +1 -0
@@ -4,3 +4,4 @@ # obj-$(CONFIG_PHY_ROCKCHIP_INNO_USB2) += phy-rockchip-inno-usb2.o +obj-$(CONFIG_PHY_ROCKCHIP_TYPEC) += phy-rockchip-typec.o
drivers/phy/rockchip/phy-rockchip-typec.c new file +796 -0
796 lines not on this page · raw message
Signature · 1 line
2.17.1
PATCH v4 7/16 usb: dwc3: add dis_enblslpm_quirk
In reply to a message not in the archiveAdd a quirk to clear the GUSB2PHYCFG.ENBLSLPM bit, which controls whether the PHY receives the suspend signal from the controller.
Refer to commit ec791d149bca("usb: dwc3: Add dis_enblslpm_quirk") in Linux Kernel.
--- drivers/usb/dwc3/core.c | 6 ++++++ drivers/usb/dwc3/core.h | 2 ++ include/dwc3-uboot.h | 1 + 3 files changed, 9 insertions(+)
drivers/usb/dwc3/core.c +6 -0
@@ -398,6 +398,9 @@ static void dwc3_phy_setup(struct dwc3 *dwc)if (dwc->dis_u2_susphy_quirk) reg &= ~DWC3_GUSB2PHYCFG_SUSPHY ; +if (dwc->dis_enblslpm_quirk) + reg &= ~DWC3_GUSB2PHYCFG_ENBLSLPM ; +dwc3_writel (dwc->regs,DWC3_GUSB2PHYCFG (0 ), reg);mdelay (100 );
@@ -719,6 +722,7 @@ int dwc3_uboot_init(struct dwc3_device *dwc3_dev) dwc->dis_u3_susphy_quirk = dwc3_dev->dis_u3_susphy_quirk; dwc->dis_u2_susphy_quirk = dwc3_dev->dis_u2_susphy_quirk; dwc->dis_del_phy_power_chg_quirk = dwc3_dev->dis_del_phy_power_chg_quirk; + dwc->dis_enblslpm_quirk = dwc3_dev->dis_enblslpm_quirk; dwc->tx_de_emphasis_quirk = dwc3_dev->tx_de_emphasis_quirk;if (dwc3_dev->tx_de_emphasis)
@@ -926,6 +930,8 @@ void dwc3_of_parse(struct dwc3 *dwc) "snps,dis_u2_susphy_quirk"); dwc->dis_del_phy_power_chg_quirk =dev_read_bool (dev,"snps,dis-del-phy-power-chg-quirk" ); + dwc->dis_enblslpm_quirk =dev_read_bool (dev, +"snps,dis_enblslpm_quirk" ); dwc->tx_de_emphasis_quirk =dev_read_bool (dev,"snps,tx_de_emphasis_quirk" ); tmp =dev_read_u8_array_ptr (dev,"snps,tx_de_emphasis" ,1 );
drivers/usb/dwc3/core.h +2 -0
@@ -162,6 +162,7 @@/* Global USB2 PHY Configuration Register */ #define DWC3_GUSB2PHYCFG_PHYSOFTRST (1 << 31)#define DWC3_GUSB2PHYCFG_SUSPHY (1 << 6) +#define DWC3_GUSB2PHYCFG_ENBLSLPM (1 << 8)#define DWC3_GUSB2PHYCFG_PHYIF (n) ((n) << 3)#define DWC3_GUSB2PHYCFG_PHYIF_MASK DWC3_GUSB2PHYCFG_PHYIF(1)#define DWC3_GUSB2PHYCFG_USBTRDTIM (n) ((n) << 10)
@@ -822,6 +823,7 @@ struct dwc3 { unsigned dis_u3_susphy_quirk:1; unsigned dis_u2_susphy_quirk:1; unsigned dis_del_phy_power_chg_quirk:1; + unsigned dis_enblslpm_quirk:1; unsigned tx_de_emphasis_quirk:1; unsigned tx_de_emphasis:2;
include/dwc3-uboot.h +1 -0
@@ -34,6 +34,7 @@ struct dwc3_device {unsigned dis_u3_susphy_quirk;unsigned dis_u2_susphy_quirk;unsigned dis_del_phy_power_chg_quirk; +unsigned dis_enblslpm_quirk;unsigned tx_de_emphasis_quirk;unsigned tx_de_emphasis;int index;
Signature · 1 line
2.17.1
Re: [PATCH v4 07/16] usb: dwc3: add dis_enblslpm_quirk
Quoted 10 lines · Frank Wang
Add a quirk to clear the GUSB2PHYCFG.ENBLSLPM bit, which controls whether the PHY receives the suspend signal from the controller.
Refer to commit
ec791d149bca("usb: dwc3: Add dis_enblslpm_quirk")in Linux Kernel.Signed-off-by Frank Wang <[email protected]>Reviewed-by Kever Yang <[email protected]>---
PATCH v4 8/16 usb: dwc3: add dis_u2_freeclk_exists_quirk
In reply to a message not in the archiveAdd a quirk to clear the GUSB2PHYCFG.U2_FREECLK_EXISTS bit, which specifies whether the USB2.0 PHY provides a free-running PHY clock, which is active when the clock control input is active.
Refer to commit 27f83eeb6b42("usb: dwc3: add dis_u2_freeclk_exists_quirk") in Linux Rockchip Kernel.
--- drivers/usb/dwc3/core.c | 6 ++++++ drivers/usb/dwc3/core.h | 2 ++ include/dwc3-uboot.h | 1 + 3 files changed, 9 insertions(+)
drivers/usb/dwc3/core.c +6 -0
@@ -401,6 +401,9 @@ static void dwc3_phy_setup(struct dwc3 *dwc)if (dwc->dis_enblslpm_quirk) reg &= ~DWC3_GUSB2PHYCFG_ENBLSLPM ; +if (dwc->dis_u2_freeclk_exists_quirk) + reg &= ~DWC3_GUSB2PHYCFG_U2_FREECLK_EXISTS ; +dwc3_writel (dwc->regs,DWC3_GUSB2PHYCFG (0 ), reg);mdelay (100 );
@@ -723,6 +726,7 @@ int dwc3_uboot_init(struct dwc3_device *dwc3_dev) dwc->dis_u2_susphy_quirk = dwc3_dev->dis_u2_susphy_quirk; dwc->dis_del_phy_power_chg_quirk = dwc3_dev->dis_del_phy_power_chg_quirk; dwc->dis_enblslpm_quirk = dwc3_dev->dis_enblslpm_quirk; + dwc->dis_u2_freeclk_exists_quirk = dwc3_dev->dis_u2_freeclk_exists_quirk; dwc->tx_de_emphasis_quirk = dwc3_dev->tx_de_emphasis_quirk;if (dwc3_dev->tx_de_emphasis)
@@ -932,6 +936,8 @@ void dwc3_of_parse(struct dwc3 *dwc) "snps,dis-del-phy-power-chg-quirk"); dwc->dis_enblslpm_quirk =dev_read_bool (dev,"snps,dis_enblslpm_quirk" ); + dwc->dis_u2_freeclk_exists_quirk =dev_read_bool (dev, +"snps,dis-u2-freeclk-exists-quirk" ); dwc->tx_de_emphasis_quirk =dev_read_bool (dev,"snps,tx_de_emphasis_quirk" ); tmp =dev_read_u8_array_ptr (dev,"snps,tx_de_emphasis" ,1 );
drivers/usb/dwc3/core.h +2 -0
@@ -161,6 +161,7 @@/* Global USB2 PHY Configuration Register */ #define DWC3_GUSB2PHYCFG_PHYSOFTRST (1 << 31) +#define DWC3_GUSB2PHYCFG_U2_FREECLK_EXISTS (1 << 30)#define DWC3_GUSB2PHYCFG_SUSPHY (1 << 6)#define DWC3_GUSB2PHYCFG_ENBLSLPM (1 << 8)#define DWC3_GUSB2PHYCFG_PHYIF (n) ((n) << 3)
@@ -824,6 +825,7 @@ struct dwc3 { unsigned dis_u2_susphy_quirk:1; unsigned dis_del_phy_power_chg_quirk:1; unsigned dis_enblslpm_quirk:1; + unsigned dis_u2_freeclk_exists_quirk:1; unsigned tx_de_emphasis_quirk:1; unsigned tx_de_emphasis:2;
include/dwc3-uboot.h +1 -0
@@ -35,6 +35,7 @@ struct dwc3_device {unsigned dis_u2_susphy_quirk;unsigned dis_del_phy_power_chg_quirk;unsigned dis_enblslpm_quirk; +unsigned dis_u2_freeclk_exists_quirk;unsigned tx_de_emphasis_quirk;unsigned tx_de_emphasis;int index;
Signature · 1 line
2.17.1
Re: [PATCH v4 08/16] usb: dwc3: add dis_u2_freeclk_exists_quirk
Quoted 11 lines · Frank Wang
Add a quirk to clear the GUSB2PHYCFG.U2_FREECLK_EXISTS bit, which specifies whether the USB2.0 PHY provides a free-running PHY clock, which is active when the clock control input is active.
Refer to commit 27f83eeb6b42("usb: dwc3: add
dis_u2_freeclk_exists_quirk") in Linux Rockchip Kernel.Signed-off-by Frank Wang <[email protected]>Reviewed-by Kever Yang <[email protected]>---
PATCH v4 9/16 usb: dwc3: Add disable u2mac linestate check quirk
In reply to a message not in the archiveFrom: Jagan Teki <jagan-dyjBcgdgk7Pe9wHmmfpqLFaTQe2KTcn/@public.gmane.org>
This patch adds a quirk to disable USB 2.0 MAC linestate check during HS transmit. Refer the dwc3 databook, we can use it for some special platforms if the linestate not reflect the expected line state(J) during transmission.
When use this quirk, the controller implements a fixed 40-bit TxEndDelay after the packet is given on UTMI and ignores the linestate during the transmit of a token (during token-to-token and token-to-data IPGAP).
On some rockchip platforms (e.g. rk3399), it requires to disable the u2mac linestate check to decrease the SSPLIT token to SETUP token inter-packet delay from 566ns to 466ns, and fix the issue that FS/LS devices not recognized if inserted through USB 3.0 HUB.
Reference from below Linux commit,
commit <65db7a0c9816> ("usb: dwc3: add disable u2mac linestate check quirk")
--- drivers/usb/dwc3/core.c | 20 ++++++++++++++++++++ drivers/usb/dwc3/core.h | 7 +++++++ include/dwc3-uboot.h | 1 + 3 files changed, 28 insertions(+)
drivers/usb/dwc3/core.c +20 -0
@@ -725,6 +725,7 @@ int dwc3_uboot_init(struct dwc3_device *dwc3_dev) dwc->dis_u3_susphy_quirk = dwc3_dev->dis_u3_susphy_quirk; dwc->dis_u2_susphy_quirk = dwc3_dev->dis_u2_susphy_quirk; dwc->dis_del_phy_power_chg_quirk = dwc3_dev->dis_del_phy_power_chg_quirk; + dwc->dis_tx_ipgap_linecheck_quirk = dwc3_dev->dis_tx_ipgap_linecheck_quirk; dwc->dis_enblslpm_quirk = dwc3_dev->dis_enblslpm_quirk; dwc->dis_u2_freeclk_exists_quirk = dwc3_dev->dis_u2_freeclk_exists_quirk;
@@ -934,6 +935,8 @@ void dwc3_of_parse(struct dwc3 *dwc) "snps,dis_u2_susphy_quirk"); dwc->dis_del_phy_power_chg_quirk =dev_read_bool (dev,"snps,dis-del-phy-power-chg-quirk" ); + dwc->dis_tx_ipgap_linecheck_quirk =dev_read_bool (dev, +"snps,dis-tx-ipgap-linecheck-quirk" ); dwc->dis_enblslpm_quirk =dev_read_bool (dev,"snps,dis_enblslpm_quirk" ); dwc->dis_u2_freeclk_exists_quirk = dev_read_bool(dev,
@@ -954,6 +957,7 @@ void dwc3_of_parse(struct dwc3 *dwc)int dwc3_init (struct dwc3 *dwc) {int ret; +u32 reg;dwc3_cache_hwparams (dwc);
@@ -975,6 +979,22 @@ int dwc3_init(struct dwc3 *dwc) goto event_fail; } +if (dwc->revision >=DWC3_REVISION_250A ) { + reg =dwc3_readl (dwc->regs,DWC3_GUCTL1 ); + +/* +* Enable hardware control of sending remote wakeup +* in HS when the device is in the L1 state. +*/ +if (dwc->revision >=DWC3_REVISION_290A ) + reg |=DWC3_GUCTL1_DEV_L1_EXIT_BY_HW ; + +if (dwc->dis_tx_ipgap_linecheck_quirk) + reg |=DWC3_GUCTL1_TX_IPGAP_LINECHECK_DIS ; + +dwc3_writel (dwc->regs,DWC3_GUCTL1 , reg); + } + ret =dwc3_core_init_mode (dwc);if (ret) goto mode_fail;
drivers/usb/dwc3/core.h +7 -0
@@ -73,6 +73,7 @@#define DWC3_GCTL 0xc110#define DWC3_GEVTEN 0xc114#define DWC3_GSTS 0xc118 +#define DWC3_GUCTL1 0xc11c#define DWC3_GSNPSID 0xc120#define DWC3_GGPIO 0xc124#define DWC3_GUID 0xc128
@@ -159,6 +160,10 @@#define DWC3_GCTL_GBLHIBERNATIONEN (1 << 1)#define DWC3_GCTL_DSBLCLKGTNG (1 << 0) +/* Global User Control 1 Register */ +#define DWC3_GUCTL1_TX_IPGAP_LINECHECK_DIS BIT(28) +#define DWC3_GUCTL1_DEV_L1_EXIT_BY_HW BIT(24) +/* Global USB2 PHY Configuration Register */ #define DWC3_GUSB2PHYCFG_PHYSOFTRST (1 << 31)#define DWC3_GUSB2PHYCFG_U2_FREECLK_EXISTS (1 << 30)
@@ -771,6 +776,7 @@ struct dwc3 {#define DWC3_REVISION_260A 0x5533260a#define DWC3_REVISION_270A 0x5533270a#define DWC3_REVISION_280A 0x5533280a +#define DWC3_REVISION_290A 0x5533290aenum dwc3_ep0_next ep0_next_event;enum dwc3_ep0_state ep0state;
@@ -824,6 +830,7 @@ struct dwc3 { unsigned dis_u3_susphy_quirk:1; unsigned dis_u2_susphy_quirk:1; unsigned dis_del_phy_power_chg_quirk:1; + unsigned dis_tx_ipgap_linecheck_quirk:1; unsigned dis_enblslpm_quirk:1; unsigned dis_u2_freeclk_exists_quirk:1;
include/dwc3-uboot.h +1 -0
@@ -34,6 +34,7 @@ struct dwc3_device {unsigned dis_u3_susphy_quirk;unsigned dis_u2_susphy_quirk;unsigned dis_del_phy_power_chg_quirk; +unsigned dis_tx_ipgap_linecheck_quirk;unsigned dis_enblslpm_quirk;unsigned dis_u2_freeclk_exists_quirk;unsigned tx_de_emphasis_quirk;
Signature · 1 line
2.17.1
PATCH v4 10/16 usb: dwc3: Enable AutoRetry feature in the controller
In reply to Frank WangFrom: Jagan Teki <[email protected]>
By default when core sees any transaction error (CRC or overflow) it replies with terminating retry ACK (Retry=1 and Nump == 0).
Enabling this Auto Retry feature in controller will make the core send a non-terminanting ACK upon such transaction errors. That is, ACK TP with Retry=1 and Nump != 0.
Doing so will give controller a chance to recover from transient error conditions.
Reference from below Linux commit,
commit <b138e23d3dff> ("usb: dwc3: core: Enable AutoRetry feature in the controller")
--- drivers/usb/dwc3/core.c | 9 +++++++++ drivers/usb/dwc3/core.h | 3 +++ 2 files changed, 12 insertions(+)
drivers/usb/dwc3/core.c +9 -0
@@ -995,6 +995,15 @@ int dwc3_init(struct dwc3 *dwc)dwc3_writel (dwc->regs,DWC3_GUCTL1 , reg); } +if (dwc->dr_mode ==USB_DR_MODE_HOST || + dwc->dr_mode ==USB_DR_MODE_OTG ) { + reg =dwc3_readl (dwc->regs,DWC3_GUCTL ); + + reg |=DWC3_GUCTL_HSTINAUTORETRY ; + +dwc3_writel (dwc->regs,DWC3_GUCTL , reg); + } + ret =dwc3_core_init_mode (dwc);if (ret) goto mode_fail;
drivers/usb/dwc3/core.h +3 -0
@@ -160,6 +160,9 @@#define DWC3_GCTL_GBLHIBERNATIONEN (1 << 1)#define DWC3_GCTL_DSBLCLKGTNG (1 << 0) +/* Global User Control Register */ +#define DWC3_GUCTL_HSTINAUTORETRY BIT(14) +/* Global User Control 1 Register */ #define DWC3_GUCTL1_TX_IPGAP_LINECHECK_DIS BIT(28)#define DWC3_GUCTL1_DEV_L1_EXIT_BY_HW BIT(24)
Signature · 1 line
2.17.1
A message that is not in the archive (sent off-list or not yet received): 20200511075725.26665-1-frank.wang-TNX95d0MmH7DzftRWevZcw@public.gmane.org
PATCH v4 11/16 usb: dwc3: amend UTMI/UTMIW phy interface setup
Let move 8/16-bit UTMI+ interface initialization into DWC3 core init that is convenient for both DM_USB and u-boot traditional process.
--- drivers/usb/common/common.c | 25 ++++++++++++++ drivers/usb/dwc3/core.c | 65 +++++++++++++++++++------------------ drivers/usb/dwc3/core.h | 5 +++ include/linux/usb/phy.h | 18 ++++++++++ 4 files changed, 82 insertions(+), 31 deletions(-)
drivers/usb/common/common.c +25 -0
@@ -10,6 +10,7 @@#include <dm.h> #include <linux/usb/otg.h> #include <linux/usb/ch9.h> +#include <linux/usb/phy.h> DECLARE_GLOBAL_DATA_PTR ;
@@ -64,3 +65,27 @@ enum usb_device_speed usb_get_maximum_speed(ofnode node)return USB_SPEED_UNKNOWN ; } + +#if CONFIG_IS_ENABLED (DM_USB ) +static const char *const usbphy_modes[] = { + [USBPHY_INTERFACE_MODE_UNKNOWN ] ="" , + [USBPHY_INTERFACE_MODE_UTMI ] ="utmi" , + [USBPHY_INTERFACE_MODE_UTMIW ] ="utmi_wide" , +}; + +enum usb_phy_interface usb_get_phy_mode (ofnode node) +{ +const char *phy_type; +int i; + + phy_type =ofnode_get_property (node,"phy_type" ,NULL ); +if (!phy_type) +return USBPHY_INTERFACE_MODE_UNKNOWN ; + +for (i =0 ; i <ARRAY_SIZE (usbphy_modes); i++) +if (!strcmp (phy_type, usbphy_modes[i])) +return i; + +return USBPHY_INTERFACE_MODE_UNKNOWN ; +} +#endif
drivers/usb/dwc3/core.c +34 -31
101 lines not on this page · raw message
drivers/usb/dwc3/core.h +5 -0
@@ -21,6 +21,7 @@#include <linux/usb/ch9.h> #include <linux/usb/otg.h> +#include <linux/usb/phy.h> #define DWC3_MSG_MAX 500
@@ -658,6 +659,9 @@ struct dwc3_scratchpad_array {* @maximum_speed: maximum speed requested (mainly for testing purposes) * @revision: revision register contents * @dr_mode: requested mode of operation +* @hsphy_mode: UTMI phy mode, one of following: +* - USBPHY_INTERFACE_MODE_UTMI +* - USBPHY_INTERFACE_MODE_UTMIW * @dcfg: saved contents of DCFG register * @gctl: saved contents of GCTL register * @isoch_delay: wValue from Set Isochronous Delay request;
@@ -749,6 +753,7 @@ struct dwc3 {size_t regs_size;enum usb_dr_mode dr_mode; +enum usb_phy_interface hsphy_mode;/* used for suspend/resume */ u32 dcfg;
include/linux/usb/phy.h +18 -0
@@ -10,10 +10,28 @@#ifndef __LINUX_USB_PHY_H#define __LINUX_USB_PHY_H +#include <dm/ofnode.h> +enum usb_phy_interface {USBPHY_INTERFACE_MODE_UNKNOWN ,USBPHY_INTERFACE_MODE_UTMI ,USBPHY_INTERFACE_MODE_UTMIW , }; +#if CONFIG_IS_ENABLED (DM_USB ) +/** +* usb_get_phy_mode - Get phy mode for given device_node +* @np: Pointer to the given device_node +* +* The function gets phy interface string from property 'phy_type', +* and returns the corresponding enum usb_phy_interface +*/ +enum usb_phy_interface usb_get_phy_mode (ofnode node); +#else +static inline enum usb_phy_interface usb_get_phy_mode (ofnode node) +{ +return USBPHY_INTERFACE_MODE_UNKNOWN ; +} +#endif +#endif /* __LINUX_USB_PHY_H */
Signature · 1 line
2.17.1
PATCH v4 12/16 usb: dwc3: add make compatible for rockchip platform
In reply to a message not in the archiveRK3399 Type-C PHY is required that must hold whole USB3.0 OTG controller in resetting to hold pipe power state in P2 before initializing the PHY. This commit fixed it and added device compatible for rockchip platform.
--- drivers/usb/dwc3/dwc3-generic.c | 33 +++++++++++++++++++++++++++------ 1 file changed, 27 insertions(+), 6 deletions(-)
drivers/usb/dwc3/dwc3-generic.c +27 -6
@@ -24,6 +24,12 @@#include <clk.h> #include <usb/xhci.h> +struct dwc3_glue_data { +struct clk_bulk clks; +struct reset_ctl_bulk resets; +fdt_addr_t regs; +}; +struct dwc3_generic_plat {fdt_addr_t base;u32 maximum_speed;
@@ -47,6 +53,7 @@ static int dwc3_generic_probe(struct udevice *dev,int rc;struct dwc3_generic_plat *plat =dev_get_platdata (dev);struct dwc3 *dwc3 = &priv->dwc3; +struct dwc3_glue_data *glue =dev_get_platdata (dev->parent); dwc3->dev = dev; dwc3->maximum_speed = plat->maximum_speed;
@@ -55,10 +62,22 @@ static int dwc3_generic_probe(struct udevice *dev,dwc3_of_parse (dwc3);#endif +/* +* It must hold whole USB3.0 OTG controller in resetting to hold pipe +* power state in P2 before initializing TypeC PHY on RK3399 platform. +*/ +if (device_is_compatible (dev->parent,"rockchip,rk3399-dwc3" )) { +reset_assert_bulk (&glue->resets); +udelay (1 ); + } + rc =dwc3_setup_phy (dev, &priv->phys);if (rc)return rc; +if (device_is_compatible (dev->parent,"rockchip,rk3399-dwc3" )) +reset_deassert_bulk (&glue->resets); + priv->base =map_physmem (plat->base,DWC3_OTG_REGS_END ,MAP_NOCACHE ); dwc3->regs = priv->base +DWC3_GLOBALS_REGS_START ;
@@ -186,12 +205,6 @@ U_BOOT_DRIVER(dwc3_generic_host) = { };#endif -struct dwc3_glue_data { -struct clk_bulk clks; -struct reset_ctl_bulk resets; -fdt_addr_t regs; -}; -struct dwc3_glue_ops {void (*select_dr_mode)(struct udevice *dev,int index,enum usb_dr_mode mode);
@@ -394,6 +407,12 @@ static int dwc3_glue_probe(struct udevice *dev)if (ret)return ret; +if (glue->resets.count <1 ) { + ret =dwc3_glue_reset_init (child, glue); +if (ret) +return ret; + } +while (child) {enum usb_dr_mode dr_mode;
@@ -424,6 +443,8 @@ static const struct udevice_id dwc3_glue_ids[] = { { .compatible = "ti,dwc3", .data = (ulong)&ti_ops }, { .compatible = "ti,am437x-dwc3", .data = (ulong)&ti_ops }, { .compatible = "ti,am654-dwc3" }, + { .compatible = "rockchip,rk3328-dwc3" }, + { .compatible = "rockchip,rk3399-dwc3" }, { } };
Signature · 1 line
2.17.1
Re: [PATCH v4 12/16] usb: dwc3: add make compatible for rockchip platform
On 5/11/20 9:57 AM, Frank Wang wrote:
[...]
drivers/usb/dwc3/dwc3-generic.c static int dwc3_glue_probe(struct udevice *dev) · line 410
Quoted 5 lines
drivers/usb/dwc3/dwc3-generic.c +1
-0@@ -394,6 +407,12 @@ static int dwc3_glue_probe(struct udevice *dev)if (ret)return ret; +if (glue->resets.count <1 ) {
This condition is only true if count == 0 ?
What's the purpose of this test ?
Quoted 8 lines
drivers/usb/dwc3/dwc3-generic.c +5
-0+ ret =dwc3_glue_reset_init (child, glue); +if (ret) +return ret; + } +while (child) {enum usb_dr_mode dr_mode;
[...]
Re: [PATCH v4 12/16] usb: dwc3: add make compatible for rockchip platform
Hi Marek,
Quoted 10 lines · Marek Vasut
On 5/11/20 9:57 AM, Frank Wang wrote:
[...]drivers/usb/dwc3/dwc3-generic.c static int dwc3_glue_probe(struct udevice *dev) · line 410
Quoted 5 lines
drivers/usb/dwc3/dwc3-generic.c +1
-0@@ -394,6 +407,12 @@ static int dwc3_glue_probe(struct udevice *dev)if (ret)return ret; +if (glue->resets.count <1 ) {This condition is only true if count == 0 ?
What's the purpose of this test ?
For previous dts of the Linux kernel, the reset phandles were in dwc3-glue nodes, however, they are moved recently into dwc3 that is a child node of dwc3-glue.
So the above codes is to make compatible.
Quoted 11 lines
Quoted 8 lines
drivers/usb/dwc3/dwc3-generic.c +5
-0+ ret =dwc3_glue_reset_init (child, glue); +if (ret) +return ret; + } +while (child) {enum usb_dr_mode dr_mode;[...]
BR,
Frank
Re: [PATCH v4 12/16] usb: dwc3: add make compatible for rockchip platform
Quoted 13 lines · Frank Wang
Hi Marek,
Quoted 9 lines · Marek Vasut
On 5/11/20 9:57 AM, Frank Wang wrote:
[...]drivers/usb/dwc3/dwc3-generic.c static int dwc3_glue_probe(struct udevice *dev) · line 409
Quoted 4 lines
drivers/usb/dwc3/dwc3-generic.c +0
-0@@ -394,6 +407,12 @@ static int dwc3_glue_probe(struct udevice *dev) if (ret) return ret; + if (glue->resets.count < 1) {This condition is only true if count == 0 ?
What's the purpose of this test ?
Quoted 5 lines
For previous dts of the Linux kernel, the reset phandles were in dwc3-glue nodes, however, they are moved recently into dwc3 that is a child node of dwc3-glue.
So the above codes is to make compatible.
Why doesn't it check for count == 0 then ?
Re: [PATCH v4 12/16] usb: dwc3: add make compatible for rockchip platform
Hi Marek,
Quoted 13 lines · Marek Vasut
Quoted 12 lines · Frank Wang
Hi Marek,
Quoted 9 lines · Marek Vasut
On 5/11/20 9:57 AM, Frank Wang wrote:
[...]drivers/usb/dwc3/dwc3-generic.c static int dwc3_glue_probe(struct udevice *dev) · line 409
Quoted 4 lines
drivers/usb/dwc3/dwc3-generic.c +0
-0@@ -394,6 +407,12 @@ static int dwc3_glue_probe(struct udevice *dev) if (ret) return ret; + if (glue->resets.count < 1) {This condition is only true if count == 0 ?
What's the purpose of this test ?
Quoted 7 lines
Quoted 5 lines
For previous dts of the Linux kernel, the reset phandles were in dwc3-glue nodes, however, they are moved recently into dwc3 that is a child node of dwc3-glue.
So the above codes is to make compatible.
Why doesn't it check for count == 0 then ?
Will fix.
BR,
Frank
Re: [PATCH v4 12/16] usb: dwc3: add make compatible for rockchip platform
Quoted 16 lines · Frank Wang
Hi Marek,
Quoted 13 lines · Marek Vasut
Quoted 12 lines · Frank Wang
Hi Marek,
Quoted 9 lines · Marek Vasut
On 5/11/20 9:57 AM, Frank Wang wrote:
[...]drivers/usb/dwc3/dwc3-generic.c static int dwc3_glue_probe(struct udevice *dev) · line 409
Quoted 4 lines
drivers/usb/dwc3/dwc3-generic.c +0
-0@@ -394,6 +407,12 @@ static int dwc3_glue_probe(struct udevice *dev) if (ret) return ret; + if (glue->resets.count < 1) {This condition is only true if count == 0 ?
What's the purpose of this test ?
Quoted 8 lines
Quoted 7 lines
Quoted 5 lines
For previous dts of the Linux kernel, the reset phandles were in dwc3-glue nodes, however, they are moved recently into dwc3 that is a child node of dwc3-glue.
So the above codes is to make compatible.
Why doesn't it check for count == 0 then ?
Will fix.
Thanks.
PATCH v4 13/16 driver: usb: drop legacy rockchip xhci driver
In reply to a message not in the archiveWe have changed to use dwc3 generic driver for usb3.0 host, so the legacy Rockchip's xHCI driver is not needed, and drop it.
--- drivers/usb/host/Kconfig | 9 -- drivers/usb/host/Makefile | 1 - drivers/usb/host/xhci-rockchip.c | 196 ------------------------------- 3 files changed, 206 deletions(-) delete mode 100644 drivers/usb/host/xhci-rockchip.c
drivers/usb/host/Kconfig +0 -9
@@ -53,15 +53,6 @@ config USB_XHCI_PCI help Enables support for the PCI-based xHCI controller. -config USB_XHCI_ROCKCHIP - bool "Support for Rockchip on-chip xHCI USB controller" - depends on ARCH_ROCKCHIP - depends on DM_REGULATOR - depends on DM_USB - default y - help - Enables support for the on-chip xHCI controller on Rockchip SoCs. - config USB_XHCI_RCAR bool "Renesas RCar USB 3.0 support" default y
drivers/usb/host/Makefile +0 -1
@@ -48,7 +48,6 @@ obj-$(CONFIG_USB_XHCI_BRCM) += xhci-brcm.o obj-$(CONFIG_USB_XHCI_HCD) += xhci.o xhci-mem.o xhci-ring.o obj-$(CONFIG_USB_XHCI_DWC3) += xhci-dwc3.o obj-$(CONFIG_USB_XHCI_DWC3_OF_SIMPLE) += dwc3-of-simple.o -obj-$(CONFIG_USB_XHCI_ROCKCHIP) += xhci-rockchip.o obj-$(CONFIG_USB_XHCI_EXYNOS) += xhci-exynos5.o obj-$(CONFIG_USB_XHCI_FSL) += xhci-fsl.o obj-$(CONFIG_USB_XHCI_MTK) += xhci-mtk.o
drivers/usb/host/xhci-rockchip.c deleted +0 -196
196 lines not on this page · raw message
Signature · 1 line
2.17.1
PATCH v4 14/16 ARM: dts: rk3399-evb: usb3.0 host support
In reply to a message not in the archiveConfigure 'tcphy1' and 'usbdrd_dwc3_1' nodes to support USB3.0 host for Rockchip RK3399 Evaluation Board.
--- arch/arm/dts/rk3399-evb-u-boot.dtsi | 13 +++++++++++++ 1 file changed, 13 insertions(+)
arch/arm/dts/rk3399-evb-u-boot.dtsi +13 -0
@@ -23,3 +23,16 @@ &rk808 { u-boot,dm-pre-reloc; }; + +&tcphy1 { + status = "okay"; +}; + +&usbdrd3_1 { + status = "okay"; +}; + +&usbdrd_dwc3_1 { + dr_mode = "host"; + status = "okay"; +};
Signature · 1 line
2.17.1
PATCH v4 15/16 configs: evb-rk3399: update support usb3.0 host
In reply to Frank WangUpdate evb-rk3399 default config to support USB3.0 Host.
--- configs/evb-rk3399_defconfig | 6 ++++++ 1 file changed, 6 insertions(+)
configs/evb-rk3399_defconfig +6 -0
@@ -28,6 +28,7 @@ CONFIG_SYS_RELOC_GD_ENV_ADDR=y CONFIG_NET_RANDOM_ETHADDR=y CONFIG_ROCKCHIP_GPIO=y CONFIG_SYS_I2C_ROCKCHIP=y +CONFIG_MISC=y CONFIG_MMC_DW=y CONFIG_MMC_SDHCI=y CONFIG_MMC_SDHCI_ROCKCHIP=y
@@ -35,10 +36,13 @@ CONFIG_SF_DEFAULT_SPEED=20000000 CONFIG_DM_ETH=y CONFIG_ETH_DESIGNWARE=y CONFIG_GMAC_ROCKCHIP=y +CONFIG_PHY_ROCKCHIP_INNO_USB2=y +CONFIG_PHY_ROCKCHIP_TYPEC=y CONFIG_PMIC_RK8XX=y CONFIG_REGULATOR_PWM=y CONFIG_REGULATOR_RK8XX=y CONFIG_PWM_ROCKCHIP=y +CONFIG_DM_RESET=y CONFIG_DM_RNG=y CONFIG_RNG_ROCKCHIP=y CONFIG_BAUDRATE=1500000
@@ -49,6 +53,8 @@ CONFIG_USB_XHCI_HCD=y CONFIG_USB_XHCI_DWC3=y CONFIG_USB_EHCI_HCD=y CONFIG_USB_EHCI_GENERIC=y +CONFIG_USB_DWC3=y +CONFIG_USB_DWC3_GENERIC=y CONFIG_USB_HOST_ETHER=y CONFIG_USB_ETHER_ASIX=y CONFIG_USB_ETHER_ASIX88179=y
Signature · 1 line
2.17.1
A message that is not in the archive (sent off-list or not yet received): 20200511075830.26754-1-frank.wang-TNX95d0MmH7DzftRWevZcw@public.gmane.org
PATCH v4 16/16 roc-rk3399-pc: Enable USB3.0 Host
From: Jagan Teki <jagan-dyjBcgdgk7Pe9wHmmfpqLFaTQe2KTcn/@public.gmane.org>
Enable USB3.0 Host support for ROC-RK3399-PC boards.
Tested USB3.0 SSD on Type C1 port on board.
=> usb start
starting USB...
Bus usb@fe380000: USB EHCI 1.00
Bus usb@fe3c0000: USB EHCI 1.00
Bus dwc3: usb maximum-speed not found
Register 2000140 NbrPorts 2
Starting the controller
USB XHCI 1.10
scanning bus usb@fe380000 for devices... 1 USB Device(s) found scanning bus usb@fe3c0000 for devices... 2 USB Device(s) found scanning bus dwc3 for devices... 6 USB Device(s) found
scanning usb for storage devices... 1 Storage Device(s) found
=> usb tree
USB device tree:
1 Hub (480 Mb/s, 0mA)
u-boot EHCI Host Controller
1 Hub (480 Mb/s, 0mA)
| u-boot EHCI Host Controller
|
+-2 Hub (480 Mb/s, 100mA)
USB 2.0 Hub [MTT]
1 Hub (5 Gb/s, 0mA)
| U-Boot XHCI Host Controller
|
+-2 Hub (480 Mb/s, 0mA)
| | VIA Labs, Inc. USB2.0 Hub
| |
| +-4 Hub (480 Mb/s, 100mA)
| | USB 2.0 Hub
| |
| +-5 (480 Mb/s, 100mA)
| VIA Technologies Inc. USB 2.0 BILLBOARD 0000000000000001
|
+-3 Hub (5 Gb/s, 0mA)
| VIA Labs, Inc. USB3.0 Hub
|
+-6 Mass Storage (5 Gb/s, 224mA)
JMicron External Disk 3.0 DB12345678A2=> usb reset
resetting USB...
Bus usb@fe380000: USB EHCI 1.00
Bus usb@fe3c0000: USB EHCI 1.00
Bus dwc3: usb maximum-speed not found
Register 2000140 NbrPorts 2
Starting the controller
USB XHCI 1.10
scanning bus usb@fe380000 for devices... 1 USB Device(s) found scanning bus usb@fe3c0000 for devices... 2 USB Device(s) found scanning bus dwc3 for devices... 6 USB Device(s) found
scanning usb for storage devices... 1 Storage Device(s) found
--- configs/roc-pc-mezzanine-rk3399_defconfig | 5 +++++ configs/roc-pc-rk3399_defconfig | 6 ++++++ 2 files changed, 11 insertions(+)
configs/roc-pc-mezzanine-rk3399_defconfig +5 -0
@@ -29,6 +29,7 @@ CONFIG_ENV_IS_IN_MMC=y CONFIG_SYS_RELOC_GD_ENV_ADDR=y CONFIG_ROCKCHIP_GPIO=y CONFIG_SYS_I2C_ROCKCHIP=y +CONFIG_MISC=y CONFIG_MMC_DW=y CONFIG_MMC_DW_ROCKCHIP=y CONFIG_MMC_SDHCI=y
@@ -39,6 +40,8 @@ CONFIG_ETH_DESIGNWARE=y CONFIG_GMAC_ROCKCHIP=y CONFIG_NVME=y CONFIG_PCI=y +CONFIG_PHY_ROCKCHIP_INNO_USB2=y +CONFIG_PHY_ROCKCHIP_TYPEC=y CONFIG_PMIC_RK8XX=y CONFIG_REGULATOR_PWM=y CONFIG_REGULATOR_RK8XX=y
@@ -54,6 +57,8 @@ CONFIG_USB_XHCI_HCD=y CONFIG_USB_XHCI_DWC3=y CONFIG_USB_EHCI_HCD=y CONFIG_USB_EHCI_GENERIC=y +CONFIG_USB_DWC3=y +CONFIG_USB_DWC3_GENERIC=y CONFIG_USB_HOST_ETHER=y CONFIG_USB_ETHER_ASIX=y CONFIG_USB_ETHER_ASIX88179=y
configs/roc-pc-rk3399_defconfig +6 -0
@@ -28,6 +28,7 @@ CONFIG_ENV_IS_IN_MMC=y CONFIG_SYS_RELOC_GD_ENV_ADDR=y CONFIG_ROCKCHIP_GPIO=y CONFIG_SYS_I2C_ROCKCHIP=y +CONFIG_MISC=y CONFIG_MMC_DW=y CONFIG_MMC_DW_ROCKCHIP=y CONFIG_MMC_SDHCI=y
@@ -36,11 +37,14 @@ CONFIG_SPI_FLASH_WINBOND=y CONFIG_DM_ETH=y CONFIG_ETH_DESIGNWARE=y CONFIG_GMAC_ROCKCHIP=y +CONFIG_PHY_ROCKCHIP_INNO_USB2=y +CONFIG_PHY_ROCKCHIP_TYPEC=y CONFIG_PMIC_RK8XX=y CONFIG_REGULATOR_PWM=y CONFIG_REGULATOR_RK8XX=y CONFIG_PWM_ROCKCHIP=y CONFIG_RAM_RK3399_LPDDR4=y +CONFIG_DM_RESET=y CONFIG_BAUDRATE=1500000 CONFIG_DEBUG_UART_SHIFT=2 CONFIG_ROCKCHIP_SPI=y
@@ -50,6 +54,8 @@ CONFIG_USB_XHCI_HCD=y CONFIG_USB_XHCI_DWC3=y CONFIG_USB_EHCI_HCD=y CONFIG_USB_EHCI_GENERIC=y +CONFIG_USB_DWC3=y +CONFIG_USB_DWC3_GENERIC=y CONFIG_USB_KEYBOARD=y CONFIG_USB_HOST_ETHER=y CONFIG_USB_ETHER_ASIX=y
Signature · 1 line
2.17.1