rockchip: spl: do full dram_init instead of only probing
Subsystems (3)
Heiko Stuebner
maintainerPATCH 1/2 rockchip: spl: do full dram_init instead of only probing
From: Heiko Stuebner <[email protected]>
Parts of later SPL may need RAM information as well, so do full dram_init() call, which includes the existing dram probing but also initializes the ram information in gd.
All Rockchip SoCs use a TPL+SPL combination now, so that's ok for all of them.
--- arch/arm/mach-rockchip/spl.c | 6 ++++-- 1 file changed, 4 insertions(+), 2 deletions(-)
arch/arm/mach-rockchip/spl.c +4 -2
@@ -135,13 +135,15 @@ void board_init_f(ulong dummy)/* Init ARM arch timer in arch/arm/cpu/armv7/arch_timer.c */ timer_init ();#endif -#if !defined(CONFIG_TPL ) || defined(CONFIG_SPL_OS_BOOT ) +#if !defined(CONFIG_TPL ) || defined(CONFIG_SPL_RAM )debug ("\nspl:init dram\n" ); - ret =uclass_get_device (UCLASS_RAM ,0 , &dev); + ret =dram_init ();if (ret) {printf ("DRAM init failed: %d\n" , ret);return ; } + gd->ram_top = gd->ram_base +get_effective_memsize (); + gd->ram_top =board_get_usable_ram_top (gd->ram_size);#endif preloader_console_init (); }
Signature · 1 line
2.25.1
Heiko Stuebner
maintainerPATCH 2/2 spl: add fixed memory node in target fdt also when loading ATF
From: Heiko Stuebner <[email protected]>
In a loading chain SPL -> ATF (->OP-TEE) -> U-Boot, ATF and a subsequent OP-TEE will re-use the same fdt as the U-Boot target and may need the information about usable memory ranges.
Especially OP-TEE needs this to initialize dynamic shared memory (the only type U-Boot implements when talking to OP-TEE).
So allow spl_fixup_fdt() to take a fdt_blob argument, falling back to the existing CONFIG_SYS_SPL_ARGS_ADDR if needed and call it from the ATF path as well.
--- common/spl/spl.c | 19 +++++++++++++------ 1 file changed, 13 insertions(+), 6 deletions(-)
common/spl/spl.c +13 -6
@@ -58,7 +58,8 @@ static bd_t bdata __attribute__ ((section(".data")));*/ __weak void show_boot_progress (int val) {} -#if defined(CONFIG_SPL_OS_BOOT ) ||CONFIG_IS_ENABLED (HANDOFF ) +#if defined(CONFIG_SPL_OS_BOOT ) ||CONFIG_IS_ENABLED (HANDOFF ) || \ + defined(CONFIG_SPL_ATF )/* weak, default platform-specific function to initialize dram banks */ __weak int dram_init_banksize (void ) {
@@ -100,12 +101,14 @@ void __weak spl_perform_fixups(struct spl_image_info *spl_image) { } -void spl_fixup_fdt (void ) +void spl_fixup_fdt (void *fdt_blob) { -#if defined(CONFIG_SPL_OF_LIBFDT ) && defined(CONFIG_SYS_SPL_ARGS_ADDR ) -void *fdt_blob = (void *)CONFIG_SYS_SPL_ARGS_ADDR ; +#if defined(CONFIG_SPL_OF_LIBFDT )int err; +if (!fdt_blob) +return ; + err =fdt_check_header (fdt_blob);if (err <0 ) {printf ("fdt_root: %s\n" ,fdt_strerror (err));
@@ -638,7 +641,8 @@ void board_init_r(gd_t *dummy1, ulong dummy2)initr_watchdog ();#endif -if (IS_ENABLED (CONFIG_SPL_OS_BOOT ) ||CONFIG_IS_ENABLED (HANDOFF )) +if (IS_ENABLED (CONFIG_SPL_OS_BOOT ) ||CONFIG_IS_ENABLED (HANDOFF ) || +IS_ENABLED (CONFIG_SPL_ATF ))dram_init_banksize ();bootcount_inc ();
@@ -680,6 +684,7 @@ void board_init_r(gd_t *dummy1, ulong dummy2)#if CONFIG_IS_ENABLED (ATF )case IH_OS_ARM_TRUSTED_FIRMWARE :debug ("Jumping to U-Boot via ARM Trusted Firmware\n" ); +spl_fixup_fdt (spl_image.fdt_addr);spl_invoke_atf (&spl_image);break ;#endif
@@ -699,7 +704,9 @@ void board_init_r(gd_t *dummy1, ulong dummy2)#ifdef CONFIG_SPL_OS_BOOT case IH_OS_LINUX :debug ("Jumping to Linux\n" ); -spl_fixup_fdt (); +#if defined(CONFIG_SYS_SPL_ARGS_ADDR ) +spl_fixup_fdt ((void *)CONFIG_SYS_SPL_ARGS_ADDR ); +#endif spl_board_prepare_for_linux ();jump_to_image_linux (&spl_image);#endif
Signature · 1 line
2.25.1
PATCH 2/2 spl: add fixed memory node in target fdt also when loading ATF
Quoted 9 lines · Heiko Stuebner
From: Heiko Stuebner <[email protected]>
In a loading chain SPL -> ATF (->OP-TEE) -> U-Boot, ATF and a subsequent OP-TEE will re-use the same fdt as the U-Boot target and may need the information about usable memory ranges.
Especially OP-TEE needs this to initialize dynamic shared memory (the only type U-Boot implements when talking to OP-TEE).
Quoted 7 lines
So allow
spl_fixup_fdt()to take afdt_blobargument, falling back to the existingCONFIG_SYS_SPL_ARGS_ADDRif needed and call it from the ATF path as well.Signed-off-by Heiko Stuebner <[email protected]>Change-Id: I95d555e170534ad7fd03b183773e0b1f2d90d486
Remove this Change-Id.
For other parts:
Thanks,
- Kever
Quoted 65 lines
--- common/spl/spl.c | 19 +++++++++++++------ 1 file changed, 13 insertions(+), 6 deletions(-)common/spl/spl.c +13
-6@@ -58,7 +58,8 @@ static bd_t bdata __attribute__ ((section(".data")));*/ __weak void show_boot_progress (int val) {} -#if defined(CONFIG_SPL_OS_BOOT ) ||CONFIG_IS_ENABLED (HANDOFF ) +#if defined(CONFIG_SPL_OS_BOOT ) ||CONFIG_IS_ENABLED (HANDOFF ) || \ + defined(CONFIG_SPL_ATF )/* weak, default platform-specific function to initialize dram banks */ __weak int dram_init_banksize (void ) {@@ -100,12 +101,14 @@ void __weak spl_perform_fixups(struct spl_image_info *spl_image) { } -void spl_fixup_fdt (void ) +void spl_fixup_fdt (void *fdt_blob) { -#if defined(CONFIG_SPL_OF_LIBFDT ) && defined(CONFIG_SYS_SPL_ARGS_ADDR ) -void *fdt_blob = (void *)CONFIG_SYS_SPL_ARGS_ADDR ; +#if defined(CONFIG_SPL_OF_LIBFDT )int err; +if (!fdt_blob) +return ; + err =fdt_check_header (fdt_blob);if (err <0 ) {printf ("fdt_root: %s\n" ,fdt_strerror (err));@@ -638,7 +641,8 @@ void board_init_r(gd_t *dummy1, ulong dummy2)initr_watchdog ();#endif -if (IS_ENABLED (CONFIG_SPL_OS_BOOT ) ||CONFIG_IS_ENABLED (HANDOFF )) +if (IS_ENABLED (CONFIG_SPL_OS_BOOT ) ||CONFIG_IS_ENABLED (HANDOFF ) || +IS_ENABLED (CONFIG_SPL_ATF ))dram_init_banksize ();bootcount_inc ();@@ -680,6 +684,7 @@ void board_init_r(gd_t *dummy1, ulong dummy2)#if CONFIG_IS_ENABLED (ATF )case IH_OS_ARM_TRUSTED_FIRMWARE :debug ("Jumping to U-Boot via ARM Trusted Firmware\n" ); +spl_fixup_fdt (spl_image.fdt_addr);spl_invoke_atf (&spl_image);break ;#endif @@ -699,7 +704,9 @@ void board_init_r(gd_t *dummy1, ulong dummy2)#ifdef CONFIG_SPL_OS_BOOT case IH_OS_LINUX :debug ("Jumping to Linux\n" ); -spl_fixup_fdt (); +#if defined(CONFIG_SYS_SPL_ARGS_ADDR ) +spl_fixup_fdt ((void *)CONFIG_SYS_SPL_ARGS_ADDR ); +#endif spl_board_prepare_for_linux ();jump_to_image_linux (&spl_image);#endif
Kever Yang
NAKPATCH 1/2 rockchip: spl: do full dram_init instead of only probing
In reply to Heiko StuebnerQuoted 5 lines · Heiko Stuebner
From: Heiko Stuebner <[email protected]>
Parts of later SPL may need RAM information as well, so do full
dram_init()call, which includes the existing dram probing but also initializes the ram information in gd.
NAK.
I would prefer to use DM interface and leave the decision of ram initialization to the ram driver.
Quoted 3 lines
All Rockchip SoCs use a TPL+SPL combination now, so that's ok for all of them.
Still not all of the board use the combination.
Quoted 3 lines
Signed-off-by Heiko Stuebner <[email protected]>Change-Id I2c7496f2d88d65a9f80f74d2139bf307bb4b442b
Please remove the Change-Id next time.
Thanks,
- Kever
Quoted 26 lines
--- arch/arm/mach-rockchip/spl.c | 6 ++++-- 1 file changed, 4 insertions(+), 2 deletions(-)arch/arm/mach-rockchip/spl.c +4
-2@@ -135,13 +135,15 @@ void board_init_f(ulong dummy)/* Init ARM arch timer in arch/arm/cpu/armv7/arch_timer.c */ timer_init ();#endif -#if !defined(CONFIG_TPL ) || defined(CONFIG_SPL_OS_BOOT ) +#if !defined(CONFIG_TPL ) || defined(CONFIG_SPL_RAM )debug ("\nspl:init dram\n" ); - ret =uclass_get_device (UCLASS_RAM ,0 , &dev); + ret =dram_init ();if (ret) {printf ("DRAM init failed: %d\n" , ret);return ; } + gd->ram_top = gd->ram_base +get_effective_memsize (); + gd->ram_top =board_get_usable_ram_top (gd->ram_size);#endif preloader_console_init (); }
Heiko Stübner
maintainerPATCH 1/2 rockchip: spl: do full dram_init instead of only probing
Hi Kever,
Am Freitag, 15. Mai 2020, 04:07:41 CEST schrieb Kever Yang:
Quoted 12 lines · Heiko Stuebner
Quoted 5 lines
From: Heiko Stuebner <[email protected]>
Parts of later SPL may need RAM information as well, so do full
dram_init()call, which includes the existing dram probing but also initializes the ram information in gd.NAK.
I would prefer to use DM interface and leave the decision of ram initialization to the ram driver.
With CONFIG_SPL_RAM, we get dram_init from mach-rockchip/sdram.c not some board-specific variant and the in the code change below you can see that it is guarded by such a defined(CONFIG_SPL_RAM).
That dram_init() function does only:
- uclass_get_device(UCLASS_RAM, 0, &dev);
- ram_get_info(dev, &ram);
- gd->ram_size = ram.size;
So the only difference between the old code and my change is that it will store information about usable ram in the gd struct, so that other parts of the SPL can access it - and we of course keep using the DM interface as before ;-) .
Heiko
Quoted 42 lines
Quoted 2 lines
All Rockchip SoCs use a TPL+SPL combination now, so that's ok for all of them.
Still not all of the board use the combination.
Quoted 3 lines
Signed-off-by Heiko Stuebner <[email protected]>Change-Id I2c7496f2d88d65a9f80f74d2139bf307bb4b442bPlease remove the Change-Id next time.
Thanks,
- Kever
Quoted 26 lines
--- arch/arm/mach-rockchip/spl.c | 6 ++++-- 1 file changed, 4 insertions(+), 2 deletions(-)arch/arm/mach-rockchip/spl.c +4
-2@@ -135,13 +135,15 @@ void board_init_f(ulong dummy)/* Init ARM arch timer in arch/arm/cpu/armv7/arch_timer.c */ timer_init ();#endif -#if !defined(CONFIG_TPL ) || defined(CONFIG_SPL_OS_BOOT ) +#if !defined(CONFIG_TPL ) || defined(CONFIG_SPL_RAM )debug ("\nspl:init dram\n" ); - ret =uclass_get_device (UCLASS_RAM ,0 , &dev); + ret =dram_init ();if (ret) {printf ("DRAM init failed: %d\n" , ret);return ; } + gd->ram_top = gd->ram_base +get_effective_memsize (); + gd->ram_top =board_get_usable_ram_top (gd->ram_size);#endif preloader_console_init (); }