lan743x: Added fixed link support
Subsystems (3)
PATCH 1/1 lan743x: Added fixed link support
Microchip lan7431 is frequently connected to a phy. However, it can also be directly connected to a MII remote peer without any phy in between. For supporting such a phyless hardware setup in Linux we added the capability to the driver to understand the fixed-link and the phy-connection-type entries in the device tree.
If a fixed-link node is configured in the device tree the lan7431 device will deactivate auto negotiation and uses the speed and duplex settings configured in the fixed-link node.
Also the phy-connection-type can be configured in the device tree and in case of a fixed-link connection the RGMII mode can be configured, all other modes fall back to the default: GMII.
Example:
&pcie {
status = "okay";
host@0 {
reg = <0 0 0 0 0>;
#address-cells = <3>;
#size-cells = <2>;
ethernet@0 {
compatible = "weyland-yutani,noscom1", "microchip,lan743x";
status = "okay";
reg = <0 0 0 0 0>;
phy-connection-type = "rgmii";
fixed-link {
speed = <100>;
full-duplex;
};
};
};
};--- drivers/net/ethernet/microchip/lan743x_main.c | 94 +++++++++++++++++-- drivers/net/ethernet/microchip/lan743x_main.h | 4 + 2 files changed, 89 insertions(+), 9 deletions(-)
drivers/net/ethernet/microchip/lan743x_main.c +85 -9
@@ -9,9 +9,12 @@#include <linux/microchipphy.h> #include <linux/net_tstamp.h> #include <linux/phy.h> +#include <linux/phy_fixed.h> #include <linux/rtnetlink.h> #include <linux/iopoll.h> #include <linux/crc16.h> +#include <linux/of_mdio.h> +#include <linux/of_net.h> #include "lan743x_main.h" #include "lan743x_ethtool.h"
@@ -974,6 +977,8 @@ static void lan743x_phy_close(struct lan743x_adapter *adapter)phy_stop (netdev->phydev);phy_disconnect (netdev->phydev); +if (of_phy_is_fixed_link (adapter->pdev->dev.of_node)) +of_phy_deregister_fixed_link (adapter->pdev->dev.of_node); netdev->phydev =NULL ; }
@@ -982,18 +987,86 @@ static int lan743x_phy_open(struct lan743x_adapter *adapter)struct lan743x_phy *phy = &adapter->phy;struct phy_device *phydev;struct net_device *netdev; +struct device_node *phynode; +u32 data; +phy_interface_t phyifc =PHY_INTERFACE_MODE_GMII ; +bool fixed_link = false;int ret = -EIO ; netdev = adapter->netdev; - phydev =phy_find_first (adapter->mdiobus); -if (!phydev) - goto return_error; + phynode =of_node_get (adapter->pdev->dev.of_node); +if (phynode) +of_get_phy_mode (phynode, &phyifc); + +/* check if a fixed-link is defined in device-tree */ +if (phynode &&of_phy_is_fixed_link (phynode)) { + fixed_link = true; +netdev_dbg (netdev,"fixed-link detected\n" ); + + ret =of_phy_register_fixed_link (phynode); +if (ret) { +netdev_err (netdev,"cannot register fixed PHY\n" ); + goto return_error; + } - ret =phy_connect_direct (netdev, phydev, - lan743x_phy_link_status_change, -PHY_INTERFACE_MODE_GMII ); -if (ret) - goto return_error; + phydev =of_phy_connect (netdev, phynode, + lan743x_phy_link_status_change, +0 , phyifc); +if (!phydev) + goto return_error; + +/* Configure MAC to fixed link parameters */ + data =lan743x_csr_read (adapter,MAC_CR ); +/* Disable auto negotiation */ + data &= ~(MAC_CR_ADD_ |MAC_CR_ASD_ ); +/* Set duplex mode */ +if (phydev->duplex) + data |=MAC_CR_DPX_ ; +else + data &= ~MAC_CR_DPX_ ; +/* Set bus speed */ +switch (phydev->speed) { +case 10 : + data &= ~MAC_CR_CFG_H_ ; + data &= ~MAC_CR_CFG_L_ ; +break ; +case 100 : + data &= ~MAC_CR_CFG_H_ ; + data |=MAC_CR_CFG_L_ ; +break ; +case 1000 : + data |=MAC_CR_CFG_H_ ; + data |=MAC_CR_CFG_L_ ; +break ; + } +/* Set interface mode */ +if (phyifc ==PHY_INTERFACE_MODE_RGMII || + phyifc ==PHY_INTERFACE_MODE_RGMII_ID || + phyifc ==PHY_INTERFACE_MODE_RGMII_RXID || + phyifc ==PHY_INTERFACE_MODE_RGMII_TXID ) +/* RGMII */ + data &= ~MAC_CR_MII_EN_ ; +else +/* GMII */ + data |=MAC_CR_MII_EN_ ; +lan743x_csr_write (adapter,MAC_CR , data); + }else { + phydev =phy_find_first (adapter->mdiobus); +if (!phydev) + goto return_error; + + ret =phy_connect_direct (netdev, phydev, + lan743x_phy_link_status_change, +PHY_INTERFACE_MODE_GMII ); +/* Note: We cannot use phyifc here because this would be SGMII +* on a standard PC. +*/ +if (ret) + goto return_error; + } + +if (phynode) +of_node_put (phynode);/* MAC doesn't support 1000T Half */ phy_remove_link_mode (phydev, ETHTOOL_LINK_MODE_1000baseT_Half_BIT);
@@ -1004,10 +1077,13 @@ static int lan743x_phy_open(struct lan743x_adapter *adapter) phy->fc_autoneg = phydev->autoneg;phy_start (phydev); -phy_start_aneg (phydev); +if (!fixed_link) +phy_start_aneg (phydev);return 0 ; return_error: +if (phynode) +of_node_put (phynode);return ret; }
drivers/net/ethernet/microchip/lan743x_main.h +4 -0
@@ -104,10 +104,14 @@ ((value << 0) & FCT_FLOW_CTL_ON_THRESHOLD_)#define MAC_CR (0x100) +#define MAC_CR_MII_EN_ BIT(19)#define MAC_CR_EEE_EN_ BIT(17)#define MAC_CR_ADD_ BIT(12)#define MAC_CR_ASD_ BIT(11)#define MAC_CR_CNTR_RST_ BIT(5) +#define MAC_CR_DPX_ BIT(3) +#define MAC_CR_CFG_H_ BIT(2) +#define MAC_CR_CFG_L_ BIT(1)#define MAC_CR_RST_ BIT(0)#define MAC_RX (0x104)
Signature · 1 line
2.20.1
Quoted 137 lines · Roelof Berg
Microchip lan7431 is frequently connected to a phy. However, it can also be directly connected to a MII remote peer without any phy in between. For supporting such a phyless hardware setup in Linux we added the capability to the driver to understand the fixed-link and the phy-connection-type entries in the device tree.
If a fixed-link node is configured in the device tree the lan7431 device will deactivate auto negotiation and uses the speed and duplex settings configured in the fixed-link node.
Also the phy-connection-type can be configured in the device tree and in case of a fixed-link connection the RGMII mode can be configured, all other modes fall back to the default: GMII.
Example:
&pcie { status = "okay"; host@0 { reg = <0 0 0 0 0>; #address-cells = <3>; #size-cells = <2>; ethernet@0 { compatible = "weyland-yutani,noscom1", "microchip,lan743x"; status = "okay"; reg = <0 0 0 0 0>; phy-connection-type = "rgmii"; fixed-link { speed = <100>; full-duplex; }; }; }; };Signed-off-by Roelof Berg <[email protected]>--- drivers/net/ethernet/microchip/lan743x_main.c | 94 +++++++++++++++++-- drivers/net/ethernet/microchip/lan743x_main.h | 4 + 2 files changed, 89 insertions(+), 9 deletions(-)drivers/net/ethernet/microchip/lan743x_main.c +54
-8@@ -9,9 +9,12 @@#include <linux/microchipphy.h> #include <linux/net_tstamp.h> #include <linux/phy.h> +#include <linux/phy_fixed.h> #include <linux/rtnetlink.h> #include <linux/iopoll.h> #include <linux/crc16.h> +#include <linux/of_mdio.h> +#include <linux/of_net.h> #include "lan743x_main.h" #include "lan743x_ethtool.h" @@ -974,6 +977,8 @@ static void lan743x_phy_close(struct lan743x_adapter *adapter)phy_stop (netdev->phydev);phy_disconnect (netdev->phydev); +if (of_phy_is_fixed_link (adapter->pdev->dev.of_node)) +of_phy_deregister_fixed_link (adapter->pdev->dev.of_node); netdev->phydev =NULL ; }@@ -982,18 +987,86 @@ static int lan743x_phy_open(struct lan743x_adapter *adapter)struct lan743x_phy *phy = &adapter->phy;struct phy_device *phydev;struct net_device *netdev; +struct device_node *phynode; +u32 data; +phy_interface_t phyifc =PHY_INTERFACE_MODE_GMII ; +bool fixed_link = false;int ret = -EIO ; netdev = adapter->netdev; - phydev =phy_find_first (adapter->mdiobus); -if (!phydev) - goto return_error; + phynode =of_node_get (adapter->pdev->dev.of_node); +if (phynode) +of_get_phy_mode (phynode, &phyifc); + +/* check if a fixed-link is defined in device-tree */ +if (phynode &&of_phy_is_fixed_link (phynode)) { + fixed_link = true; +netdev_dbg (netdev,"fixed-link detected\n" ); + + ret =of_phy_register_fixed_link (phynode); +if (ret) { +netdev_err (netdev,"cannot register fixed PHY\n" ); + goto return_error; + } - ret =phy_connect_direct (netdev, phydev, - lan743x_phy_link_status_change, -PHY_INTERFACE_MODE_GMII ); -if (ret) - goto return_error; + phydev =of_phy_connect (netdev, phynode, + lan743x_phy_link_status_change, +0 , phyifc); +if (!phydev) + goto return_error; + +/* Configure MAC to fixed link parameters */ + data =lan743x_csr_read (adapter,MAC_CR ); +/* Disable auto negotiation */ + data &= ~(MAC_CR_ADD_ |MAC_CR_ASD_ ); +/* Set duplex mode */ +if (phydev->duplex) + data |=MAC_CR_DPX_ ; +else + data &= ~MAC_CR_DPX_ ; +/* Set bus speed */ +switch (phydev->speed) { +case 10 : + data &= ~MAC_CR_CFG_H_ ; + data &= ~MAC_CR_CFG_L_ ; +break ; +case 100 : + data &= ~MAC_CR_CFG_H_ ; + data |=MAC_CR_CFG_L_ ; +break ; +case 1000 : + data |=MAC_CR_CFG_H_ ; + data |=MAC_CR_CFG_L_ ; +break ; + } +/* Set interface mode */
drivers/net/ethernet/microchip/lan743x_main.c static int lan743x_phy_open(struct lan743x_adapter *adapter) · line 1052
Quoted 10 lines
drivers/net/ethernet/microchip/lan743x_main.c +10
-0+if (phyifc ==PHY_INTERFACE_MODE_RGMII || + phyifc ==PHY_INTERFACE_MODE_RGMII_ID || + phyifc ==PHY_INTERFACE_MODE_RGMII_RXID || + phyifc ==PHY_INTERFACE_MODE_RGMII_TXID ) +/* RGMII */ + data &= ~MAC_CR_MII_EN_ ; +else +/* GMII */ + data |=MAC_CR_MII_EN_ ; +lan743x_csr_write (adapter,MAC_CR , data);
All of this should be done in your adjust_link callback, I believe you did it here because you made phy_start_aneg() conditional on not finding a fixed PHY, but the point of a fixed PHY is to provide a full emulation, including that of the state machine transitions.
Quoted 21 lines
drivers/net/ethernet/microchip/lan743x_main.c +17
-0+ }else { + phydev =phy_find_first (adapter->mdiobus); +if (!phydev) + goto return_error; + + ret =phy_connect_direct (netdev, phydev, + lan743x_phy_link_status_change, +PHY_INTERFACE_MODE_GMII ); +/* Note: We cannot use phyifc here because this would be SGMII +* on a standard PC. +*/ +if (ret) + goto return_error; + } + +if (phynode) +of_node_put (phynode);/* MAC doesn't support 1000T Half */ phy_remove_link_mode (phydev, ETHTOOL_LINK_MODE_1000baseT_Half_BIT);
drivers/net/ethernet/microchip/lan743x_main.c static int lan743x_phy_open(struct lan743x_adapter *adapter) · line 1081
Quoted 6 lines
drivers/net/ethernet/microchip/lan743x_main.c +2
-1@@ -1004,10 +1077,13 @@ static int lan743x_phy_open(struct lan743x_adapter *adapter) phy->fc_autoneg = phydev->autoneg;phy_start (phydev); -phy_start_aneg (phydev); +if (!fixed_link) +phy_start_aneg (phydev);
phy_start() should already trigger an auto-negotiation restart if necessary, so this calls seems to be redundant if nothing else. If someone it must be kept, it should not be made conditional on the fixed link.
Signature · 1 line
Florian