arm64: dts: qcom: apq8016-sbc-d3: Add Qualcomm APQ8016 SBC + D3Camera mezzanine
PATCH v2 1/1 arm64: dts: qcom: apq8016-sbc-d3: Add Qualcomm APQ8016 SBC + D3Camera mezzanine
Add device treee support for the Qualcomm APQ8016 SBC, otherwise known as the Dragonboard 410c with the D3Camera mezzanine expansion board.
The D3Camera mezzanine ships in a kit with a OmniVision 5640 sensor module, which is what this DT targets.
---
Changes since v1:
- Vinod: Changed license to GPL+BSD
- Vinod: Changed copyright year to 2020
- Nico: Changed name of mezzanine to d3camera
arch/arm64/boot/dts/qcom/Makefile | 1 + .../boot/dts/qcom/apq8016-sbc-d3camera.dts | 45 +++++++++++++++++++ 2 files changed, 46 insertions(+) create mode 100644 arch/arm64/boot/dts/qcom/apq8016-sbc-d3camera.dts
arch/arm64/boot/dts/qcom/Makefile +1 -0
@@ -1,5 +1,6 @@ # SPDX-License-Identifier: GPL-2.0 dtb-$(CONFIG_ARCH_QCOM) += apq8016-sbc.dtb +dtb-$(CONFIG_ARCH_QCOM) += apq8016-sbc-d3camera.dtb dtb-$(CONFIG_ARCH_QCOM) += apq8096-db820c.dtb dtb-$(CONFIG_ARCH_QCOM) += apq8096-ifc6640.dtb dtb-$(CONFIG_ARCH_QCOM) += ipq6018-cp01-c1.dtb
arch/arm64/boot/dts/qcom/apq8016-sbc-d3camera.dts new file +45 -0
45 lines not on this page · raw message
Signature · 1 line
2.25.1
Quoted 37 lines · Robert Foss
Add device treee support for the Qualcomm APQ8016 SBC, otherwise known as the Dragonboard 410c with the D3Camera mezzanine expansion board.
The D3Camera mezzanine ships in a kit with a OmniVision 5640 sensor module, which is what this DT targets.
Signed-off-by Robert Foss <[email protected]>---
Changes since v1:
- Vinod: Changed license to GPL+BSD
- Vinod: Changed copyright year to 2020
- Nico: Changed name of mezzanine to d3cameraarch/arm64/boot/dts/qcom/Makefile | 1 + .../boot/dts/qcom/apq8016-sbc-d3camera.dts | 45 +++++++++++++++++++ 2 files changed, 46 insertions(+) create mode 100644 arch/arm64/boot/dts/qcom/apq8016-sbc-d3camera.dtsarch/arm64/boot/dts/qcom/Makefile +1
-0@@ -1,5 +1,6 @@ # SPDX-License-Identifier: GPL-2.0 dtb-$(CONFIG_ARCH_QCOM) += apq8016-sbc.dtb +dtb-$(CONFIG_ARCH_QCOM) += apq8016-sbc-d3camera.dtb dtb-$(CONFIG_ARCH_QCOM) += apq8096-db820c.dtb dtb-$(CONFIG_ARCH_QCOM) += apq8096-ifc6640.dtb dtb-$(CONFIG_ARCH_QCOM) += ipq6018-cp01-c1.dtbarch/arm64/boot/dts/qcom/apq8016-sbc-d3camera.dts new file +0
-0
arch/arm64/boot/dts/qcom/apq8016-sbc-d3camera.dts line 3
Quoted 3 lines
arch/arm64/boot/dts/qcom/apq8016-sbc-d3camera.dts new file +3
-0@@ -0,0 +1,45 @@ +// SPDX-License-Identifier: GPL-2.0 OR BSD-3-Clause +/* + * Copyright (c) 2020, The Linux Foundation. All rights reserved.
This copyright is incorrect, and should instead assigned to Linaro. I'll spin a new version with this change.
Quoted 45 lines
arch/arm64/boot/dts/qcom/apq8016-sbc-d3camera.dts new file +42
-1+ */ + +/dts-v1/; + +#include "apq8016-sbc.dtsi" + +/ { + model = "Qualcomm Technologies, Inc. APQ 8016 SBC w/ D3Camera Mezzanine"; + compatible = "qcom,apq8016-sbc", "qcom,apq8016", "qcom,sbc"; +}; + +&cci_i2c0 { + /delete-node/ camera_rear@3b; + + camera_rear@76 { + compatible = "ovti,ov5640"; + reg = <0x76>; + + enable-gpios = <&msmgpio 34 GPIO_ACTIVE_HIGH>; + reset-gpios = <&msmgpio 35 GPIO_ACTIVE_LOW>; + pinctrl-names = "default"; + pinctrl-0 = <&camera_rear_default>; + + clocks = <&gcc GCC_CAMSS_MCLK0_CLK>; + clock-names = "xclk"; + clock-frequency = <23880000>; + + vdddo-supply = <&camera_vdddo_1v8>; + vdda-supply = <&camera_vdda_2v8>; + vddd-supply = <&camera_vddd_1v5>; + + status = "ok"; + + port { + ov5640_ep: endpoint { + clock-lanes = <1>; + data-lanes = <0 2>; + remote-endpoint = <&csiphy0_ep>; + }; + }; + }; +}; --2.25.1