DC Patches May 15, 2020
cover DC Patches May 15, 2020
This DC patchset brings improvements in multiple areas. In summary, we highlight:
* FW updates;
* Fix issues on DML, modes, ABM, and others;
* Remove file that use FPU unit;
* Improvements on DMUB, DM, DP, and others.
Anthony Koo (2):
drm/amd/display: FW release 1.0.10
drm/amd/display: FW Release 1.0.11
Aric Cyr (1):
drm/amd/display: 3.2.85
Dmytro Laktyushkin (5):
drm/amd/display: fix and simplify pipe split logic drm/amd/display: update dml interfaces and variables drm/amd/display: correct rn NUM_VMID drm/amd/display: fix dml log2 function drm/amd/display: fix dml immediate flip input
Jaehyun Chung (1):
drm/amd/display: Handle persistence in DM
Jake Wang (1):
drm/amd/display: vbios data table packing
Jinze Xu (1):
drm/amd/display: Set/Reset avmute when disable/enable stream
Nicholas Kazlauskas (6):
drm/amd/display: Check bss_data_size before going down legacy DMUB
load path
drm/amd/display: Don't pass invalid fw_bss_data pointer into DMUB srv drm/amd/display: Defer cursor lock until after VUPDATE drm/amd/display: Avoid pipe split when plane is too small drm/amd/display: Add DMUB firmware version helpers in DMUB service drm/amd/display: Support CW4 for DMUB ringbuffer inbox
Nikola Cornij (1):
drm/amd/display: Minimize DSC resource re-assignment
Rodrigo Siqueira (2):
drm/amd/display: Add bit swap helper based on endianness drm/amd/display: Remove dml_common_def file
Stylon Wang (1):
drm/amd/display: Fix incorrectly pruned modes with deep color
Sung Lee (1):
drm/amd/display: Do not fail if build scaling params fails
Vladimir Stempen (1):
drm/amd/display: DP training to set properly SCRAMBLING_DISABLE
Wenjing Liu (1):
drm/amd/display: DP link layer test 4.2.1.1 fix due to specs update
Wyatt Wood (1):
drm/amd/display: Fix ABM memory alignment issue
Yongqiang Sun (2):
drm/amd/display: Implement some asic specific abm call backs. drm/amd/display: Remove nv12 work around
.../gpu/drm/amd/display/amdgpu_dm/amdgpu_dm.c | 106 +++++--- .../display/amdgpu_dm/amdgpu_dm_services.c | 25 -- .../drm/amd/display/dc/bios/bios_parser2.c | 98 ++++++++ .../gpu/drm/amd/display/dc/calcs/dcn_calcs.c | 21 +- drivers/gpu/drm/amd/display/dc/core/dc_link.c | 11 +- .../gpu/drm/amd/display/dc/core/dc_link_ddc.c | 13 +- .../gpu/drm/amd/display/dc/core/dc_link_dp.c | 86 ++++--- .../drm/amd/display/dc/core/dc_link_hwss.c | 2 +- .../gpu/drm/amd/display/dc/core/dc_resource.c | 28 ++- .../drm/amd/display/dc/core/dc_vm_helper.c | 3 - drivers/gpu/drm/amd/display/dc/dc.h | 5 +- .../gpu/drm/amd/display/dc/dc_bios_types.h | 4 +- drivers/gpu/drm/amd/display/dc/dc_link.h | 1 + drivers/gpu/drm/amd/display/dc/dce/dmub_abm.c | 92 ------- drivers/gpu/drm/amd/display/dc/dce/dmub_psr.c | 2 +- .../display/dc/dce110/dce110_hw_sequencer.c | 11 + .../display/dc/dce110/dce110_hw_sequencer.h | 1 + .../amd/display/dc/dcn10/dcn10_hw_sequencer.c | 72 +++++- .../amd/display/dc/dcn10/dcn10_hw_sequencer.h | 5 + .../gpu/drm/amd/display/dc/dcn10/dcn10_init.c | 2 + .../drm/amd/display/dc/dcn20/dcn20_hubbub.h | 1 + .../drm/amd/display/dc/dcn20/dcn20_hwseq.c | 6 +- .../gpu/drm/amd/display/dc/dcn20/dcn20_init.c | 2 + .../drm/amd/display/dc/dcn20/dcn20_resource.c | 193 ++++++++------- .../drm/amd/display/dc/dcn20/dcn20_resource.h | 7 +- .../drm/amd/display/dc/dcn21/dcn21_hubbub.c | 7 +- .../gpu/drm/amd/display/dc/dcn21/dcn21_hubp.c | 121 +-------- .../drm/amd/display/dc/dcn21/dcn21_hwseq.c | 89 +++++++ .../drm/amd/display/dc/dcn21/dcn21_hwseq.h | 6 + .../gpu/drm/amd/display/dc/dcn21/dcn21_init.c | 6 +- .../drm/amd/display/dc/dcn21/dcn21_resource.c | 4 +- drivers/gpu/drm/amd/display/dc/dm_services.h | 69 ------ drivers/gpu/drm/amd/display/dc/dml/Makefile | 2 - .../dc/dml/dcn20/display_rq_dlg_calc_20.c | 33 +-- .../dc/dml/dcn20/display_rq_dlg_calc_20.h | 1 - .../dc/dml/dcn20/display_rq_dlg_calc_20v2.c | 33 +-- .../dc/dml/dcn20/display_rq_dlg_calc_20v2.h | 1 - .../dc/dml/dcn21/display_rq_dlg_calc_21.c | 36 +-- .../dc/dml/dcn21/display_rq_dlg_calc_21.h | 2 +- .../amd/display/dc/dml/display_mode_enums.h | 6 + .../drm/amd/display/dc/dml/display_mode_lib.h | 6 +- .../amd/display/dc/dml/display_mode_structs.h | 11 + .../drm/amd/display/dc/dml/display_mode_vba.c | 60 +++-- .../drm/amd/display/dc/dml/display_mode_vba.h | 229 ++++++++++-------- .../display/dc/dml/display_rq_dlg_helpers.h | 1 - .../display/dc/dml/dml1_display_rq_dlg_calc.h | 2 - .../drm/amd/display/dc/dml/dml_common_defs.c | 43 ---- .../drm/amd/display/dc/dml/dml_common_defs.h | 37 --- .../drm/amd/display/dc/dml/dml_inline_defs.h | 19 +- .../gpu/drm/amd/display/dc/inc/dc_link_ddc.h | 2 +- .../gpu/drm/amd/display/dc/inc/dc_link_dp.h | 2 +- drivers/gpu/drm/amd/display/dc/inc/hw/hubp.h | 3 - .../gpu/drm/amd/display/dc/inc/hw_sequencer.h | 7 + drivers/gpu/drm/amd/display/dc/inc/resource.h | 2 + drivers/gpu/drm/amd/display/dmub/dmub_srv.h | 11 + .../gpu/drm/amd/display/dmub/inc/dmub_cmd.h | 16 +- .../drm/amd/display/dmub/inc/dmub_cmd_dal.h | 35 +++ .../drm/amd/display/dmub/inc/dmub_fw_meta.h | 2 + .../gpu/drm/amd/display/dmub/inc/dmub_rb.h | 6 +- .../gpu/drm/amd/display/dmub/inc/dmub_types.h | 9 +- .../gpu/drm/amd/display/dmub/src/dmub_dcn20.c | 28 ++- .../gpu/drm/amd/display/dmub/src/dmub_srv.c | 8 +- .../drm/amd/display/modules/inc/mod_stats.h | 8 +- .../amd/display/modules/power/power_helpers.c | 95 +++++--- .../gpu/drm/amd/display/modules/vmid/vmid.c | 7 +- 65 files changed, 983 insertions(+), 879 deletions(-) delete mode 100644 drivers/gpu/drm/amd/display/dc/dml/dml_common_defs.c delete mode 100644 drivers/gpu/drm/amd/display/dc/dml/dml_common_defs.h
Signature · 6 lines
2.26.2 _______________________________________________ amd-gfx mailing list [email protected] https://lists.freedesktop.org/mailman/listinfo/amd-gfx
PATCH 1/27 drm/amd/display: Minimize DSC resource re-assignment
From: Nikola Cornij <[email protected]>
[why]
Assigning a different DSC resource than the one previosly used is currently not handled. This causes black screen on mode change when more than one monitor is connected on some ASICs.
[how]
- Acquire the previously used DSC if available
- Make sure re-program is triggered if new DSC is used
--- .../gpu/drm/amd/display/dc/core/dc_resource.c | 3 ++ .../drm/amd/display/dc/dcn20/dcn20_resource.c | 28 +++++++++++++------ .../drm/amd/display/dc/dcn20/dcn20_resource.h | 2 +- 3 files changed, 23 insertions(+), 10 deletions(-)
drivers/gpu/drm/amd/display/dc/core/dc_resource.c +3 -0
@@ -2666,6 +2666,9 @@ bool pipe_need_reprogram( false == pipe_ctx_old->stream->dpms_off)return true; +if (pipe_ctx_old->stream_res.dsc != pipe_ctx->stream_res.dsc) +return true; +return false; }
drivers/gpu/drm/amd/display/dc/dcn20/dcn20_resource.c +19 -9
@@ -1663,22 +1663,32 @@ enum dc_status dcn20_build_mapped_resource(const struct dc *dc, struct dc_state } -static void acquire_dsc (struct resource_context *res_ctx, -const struct resource_pool *pool, +static void acquire_dsc (const struct dc *dc, +struct resource_context *res_ctx,struct display_stream_compressor **dsc,int pipe_idx) {int i; +const struct resource_pool *pool = dc->res_pool; +struct display_stream_compressor *dsc_old = dc->current_state->res_ctx.pipe_ctx[pipe_idx].stream_res.dsc; -ASSERT (*dsc ==NULL ); +ASSERT (*dsc ==NULL );/* If this ASSERT fails, dsc was not released properly */ *dsc =NULL ; +/* Always do 1-to-1 mapping when number of DSCs is same as number of pipes */ if (pool->res_cap->num_dsc == pool->res_cap->num_opp) { *dsc = pool->dscs[pipe_idx]; res_ctx->is_dsc_acquired[pipe_idx] = true;return ; } +/* Return old DSC to avoid the need for re-programming */ +if (dsc_old && !res_ctx->is_dsc_acquired[dsc_old->inst]) { + *dsc = dsc_old; + res_ctx->is_dsc_acquired[dsc_old->inst] = true; +return ; + } +/* Find first free DSC */ for (i =0 ; i < pool->res_cap->num_dsc; i++)if (!res_ctx->is_dsc_acquired[i]) {
@@ -1710,7 +1720,6 @@ enum dc_status dcn20_add_dsc_to_stream_resource(struct dc *dc, {enum dc_status result =DC_OK ;int i; -const struct resource_pool *pool = dc->res_pool;/* Get a DSC if required and available */ for (i =0 ; i < dc->res_pool->pipe_count; i++) {
@@ -1722,7 +1731,7 @@ enum dc_status dcn20_add_dsc_to_stream_resource(struct dc *dc,if (pipe_ctx->stream_res.dsc)continue ; -acquire_dsc (&dc_ctx->res_ctx, pool, &pipe_ctx->stream_res.dsc, i); +acquire_dsc (dc, &dc_ctx->res_ctx, &pipe_ctx->stream_res.dsc, i);/* The number of DSCs can be less than the number of pipes */ if (!pipe_ctx->stream_res.dsc) {
@@ -1850,12 +1859,13 @@ static void swizzle_to_dml_params( }bool dcn20_split_stream_for_odm ( +const struct dc *dc,struct resource_context *res_ctx, -const struct resource_pool *pool,struct pipe_ctx *prev_odm_pipe,struct pipe_ctx *next_odm_pipe) {int pipe_idx = next_odm_pipe->pipe_idx; +const struct resource_pool *pool = dc->res_pool; *next_odm_pipe = *prev_odm_pipe;
@@ -1913,7 +1923,7 @@ bool dcn20_split_stream_for_odm( } next_odm_pipe->stream_res.opp = pool->opps[next_odm_pipe->pipe_idx];if (next_odm_pipe->stream->timing.flags.DSC ==1 ) { -acquire_dsc (res_ctx, pool, &next_odm_pipe->stream_res.dsc, next_odm_pipe->pipe_idx); +acquire_dsc (dc, res_ctx, &next_odm_pipe->stream_res.dsc, next_odm_pipe->pipe_idx);ASSERT (next_odm_pipe->stream_res.dsc);if (next_odm_pipe->stream_res.dsc ==NULL )return false;
@@ -2792,7 +2802,7 @@ bool dcn20_fast_validate_bw( hsplit_pipe =dcn20_find_secondary_pipe (dc, &context->res_ctx, dc->res_pool, pipe);ASSERT (hsplit_pipe);if (!dcn20_split_stream_for_odm ( - &context->res_ctx, dc->res_pool, + dc, &context->res_ctx, pipe, hsplit_pipe)) goto validate_fail; pipe_split_from[hsplit_pipe->pipe_idx] = pipe_idx;
@@ -2821,7 +2831,7 @@ bool dcn20_fast_validate_bw( }if (context->bw_ctx.dml.vba.ODMCombineEnabled[pipe_idx]) {if (!dcn20_split_stream_for_odm ( - &context->res_ctx, dc->res_pool, + dc, &context->res_ctx, pipe, hsplit_pipe)) goto validate_fail;dcn20_build_mapped_resource (dc, context, pipe->stream);
drivers/gpu/drm/amd/display/dc/dcn20/dcn20_resource.h +1 -1
@@ -136,8 +136,8 @@ void dcn20_split_stream_for_mpc(struct pipe_ctx *primary_pipe, struct pipe_ctx *secondary_pipe);bool dcn20_split_stream_for_odm ( +const struct dc *dc,struct resource_context *res_ctx, -const struct resource_pool *pool,struct pipe_ctx *prev_odm_pipe,struct pipe_ctx *next_odm_pipe); struct pipe_ctx *dcn20_find_secondary_pipe(struct dc *dc,
Signature · 6 lines
2.26.2 _______________________________________________ amd-gfx mailing list [email protected] https://lists.freedesktop.org/mailman/listinfo/amd-gfx
PATCH 2/27 drm/amd/display: fix and simplify pipe split logic
In reply to Rodrigo SiqueiraFrom: Dmytro Laktyushkin <[email protected]>
Current odm/mpc combine logic to detect which pipes need to split logically is flawed leading to incorrect pipe merge/split operations being taken.
This change cleans up the logic and fixes the logical errors.
--- .../gpu/drm/amd/display/dc/core/dc_resource.c | 25 ++- .../drm/amd/display/dc/dcn20/dcn20_resource.c | 153 ++++++++---------- .../drm/amd/display/dc/dcn20/dcn20_resource.h | 5 +- drivers/gpu/drm/amd/display/dc/inc/resource.h | 2 + 4 files changed, 94 insertions(+), 91 deletions(-)
drivers/gpu/drm/amd/display/dc/core/dc_resource.c +19 -6
@@ -532,6 +532,24 @@ static inline void get_vp_scan_direction( *flip_horz_scan_dir = !*flip_horz_scan_dir; } +int get_num_mpc_splits (struct pipe_ctx *pipe) +{ +int mpc_split_count =0 ; +struct pipe_ctx *other_pipe = pipe->bottom_pipe; + +while (other_pipe && other_pipe->plane_state == pipe->plane_state) { + mpc_split_count++; + other_pipe = other_pipe->bottom_pipe; + } + other_pipe = pipe->top_pipe; +while (other_pipe && other_pipe->plane_state == pipe->plane_state) { + mpc_split_count++; + other_pipe = other_pipe->top_pipe; + } + +return mpc_split_count; +} +int get_num_odm_splits (struct pipe_ctx *pipe) {int odm_split_count =0 ;
@@ -556,16 +574,11 @@ static void calculate_split_count_and_index(struct pipe_ctx *pipe_ctx, int *spli/*Check for mpc split*/ struct pipe_ctx *split_pipe = pipe_ctx->top_pipe; + *split_count =get_num_mpc_splits (pipe_ctx);while (split_pipe && split_pipe->plane_state == pipe_ctx->plane_state) { (*split_idx)++; - (*split_count)++; split_pipe = split_pipe->top_pipe; } - split_pipe = pipe_ctx->bottom_pipe; -while (split_pipe && split_pipe->plane_state == pipe_ctx->plane_state) { - (*split_count)++; - split_pipe = split_pipe->bottom_pipe; - } }else {/*Get odm split index*/ struct pipe_ctx *split_pipe = pipe_ctx->prev_odm_pipe;
drivers/gpu/drm/amd/display/dc/dcn20/dcn20_resource.c +69 -84
225 lines not on this page · raw message
drivers/gpu/drm/amd/display/dc/dcn20/dcn20_resource.h +4 -1
@@ -119,7 +119,6 @@ void dcn20_set_mcif_arb_params(display_e2e_pipe_params_st *pipes, int pipe_cnt);bool dcn20_validate_bandwidth (struct dc *dc,struct dc_state *context,bool fast_validate); -int dcn20_find_previous_split_count (struct pipe_ctx *pipe); int dcn20_validate_apply_pipe_split_flags( struct dc *dc, struct dc_state *context,
@@ -140,6 +139,10 @@ bool dcn20_split_stream_for_odm(struct resource_context *res_ctx, struct pipe_ctx *prev_odm_pipe, struct pipe_ctx *next_odm_pipe); +void dcn20_acquire_dsc (const struct dc *dc, +struct resource_context *res_ctx, +struct display_stream_compressor **dsc, +int pipe_idx); struct pipe_ctx *dcn20_find_secondary_pipe(struct dc *dc, struct resource_context *res_ctx, const struct resource_pool *pool,
drivers/gpu/drm/amd/display/dc/inc/resource.h +2 -0
@@ -177,6 +177,8 @@ unsigned int resource_pixel_format_to_bpp(enum surface_pixel_format format);void get_audio_check (struct audio_info *aud_modes,struct audio_check *aud_chk); +int get_num_mpc_splits (struct pipe_ctx *pipe); +int get_num_odm_splits (struct pipe_ctx *pipe);#endif /* DRIVERS_GPU_DRM_AMD_DC_DEV_DC_INC_RESOURCE_H_ */
Signature · 6 lines
2.26.2 _______________________________________________ amd-gfx mailing list [email protected] https://lists.freedesktop.org/mailman/listinfo/amd-gfx
PATCH 3/27 drm/amd/display: Handle persistence in DM
In reply to Rodrigo SiqueiraFrom: Jaehyun Chung <[email protected]>
[Why]
Remove dm_write_persistent_data and dm_read_persistent_data as persistence should be handled in DM.
[How]
Remove functions. Move read/write calls into DM layer while maintaining logic.
--- .../display/amdgpu_dm/amdgpu_dm_services.c | 25 ------- drivers/gpu/drm/amd/display/dc/dm_services.h | 69 ------------------- .../drm/amd/display/modules/inc/mod_stats.h | 8 ++- 3 files changed, 7 insertions(+), 95 deletions(-)
drivers/gpu/drm/amd/display/amdgpu_dm/amdgpu_dm_services.c +0 -25
@@ -47,29 +47,4 @@ void dm_perf_trace_timestamp(const char *func_name, unsigned int line) { } -bool dm_write_persistent_data (struct dc_context *ctx, -const struct dc_sink *sink, -const char *module_name, -const char *key_name, -void *params, -unsigned int size, -struct persistent_data_flag *flag) -{ -/*TODO implement*/ -return false; -} - -bool dm_read_persistent_data (struct dc_context *ctx, -const struct dc_sink *sink, -const char *module_name, -const char *key_name, -void *params, -unsigned int size, -struct persistent_data_flag *flag) -{ -/*TODO implement*/ -return false; -} -/**** power component interfaces ****/ -
drivers/gpu/drm/amd/display/dc/dm_services.h +0 -69
75 lines not on this page · raw message
drivers/gpu/drm/amd/display/modules/inc/mod_stats.h +7 -1
@@ -36,7 +36,13 @@ struct mod_stats_caps {bool dummy; }; -struct mod_stats *mod_stats_create (struct dc *dc); +struct mod_stats_init_params { +unsigned int stats_enable; +unsigned int stats_entries; +}; + +struct mod_stats *mod_stats_create (struct dc *dc, +struct mod_stats_init_params *init_params);void mod_stats_destroy (struct mod_stats *mod_stats);
Signature · 6 lines
2.26.2 _______________________________________________ amd-gfx mailing list [email protected] https://lists.freedesktop.org/mailman/listinfo/amd-gfx
PATCH 4/27 drm/amd/display: Do not fail if build scaling params fails
In reply to Rodrigo SiqueiraFrom: Sung Lee <[email protected]>
[WHY]
Failing validation when building scaling parameters causes corruption to occur due to pipe splitting with smaller pixel widths than HW supports. This needs to fail silently for now to hide the corruption until the corruption itself can be fixed.
[HOW]
Do not fail validation if building scaling params fails.
--- drivers/gpu/drm/amd/display/dc/dcn20/dcn20_resource.c | 4 ++-- 1 file changed, 2 insertions(+), 2 deletions(-)
drivers/gpu/drm/amd/display/dc/dcn20/dcn20_resource.c +2 -2
@@ -2824,8 +2824,8 @@ bool dcn20_fast_validate_bw(dcn20_split_stream_for_mpc ( &context->res_ctx, dc->res_pool, pipe, hsplit_pipe); -if (!resource_build_scaling_params (pipe) || !resource_build_scaling_params (hsplit_pipe)) - goto validate_fail; +resource_build_scaling_params (pipe); +resource_build_scaling_params (hsplit_pipe); } pipe_split_from[hsplit_pipe->pipe_idx] = pipe_idx; }
Signature · 6 lines
2.26.2 _______________________________________________ amd-gfx mailing list [email protected] https://lists.freedesktop.org/mailman/listinfo/amd-gfx
PATCH 5/27 drm/amd/display: DP training to set properly SCRAMBLING_DISABLE
In reply to Rodrigo SiqueiraFrom: Vladimir Stempen <[email protected]>
[Why]
DP training sequence to set SCRAMBLING_DISABLE bit properly based on training pattern - per DP Spec.
[How]
Update dpcd_pattern.v1_4.SCRAMBLING_DISABLE with 1 for TPS1, TPS2, TPS3, but not for TPS4.
--- .../gpu/drm/amd/display/dc/core/dc_link_dp.c | 27 +++++++++++++++++++ 1 file changed, 27 insertions(+)
drivers/gpu/drm/amd/display/dc/core/dc_link_dp.c +27 -0
@@ -219,6 +219,30 @@ static enum dpcd_training_patternsreturn dpcd_tr_pattern; } +static uint8_t dc_dp_initialize_scrambling_data_symbols ( +struct dc_link *link, +enum dc_dp_training_pattern pattern) +{ +uint8_t disable_scrabled_data_symbols =0 ; + +switch (pattern) { +case DP_TRAINING_PATTERN_SEQUENCE_1 : +case DP_TRAINING_PATTERN_SEQUENCE_2 : +case DP_TRAINING_PATTERN_SEQUENCE_3 : + disable_scrabled_data_symbols =1 ; +break ; +case DP_TRAINING_PATTERN_SEQUENCE_4 : + disable_scrabled_data_symbols =0 ; +break ; +default : +ASSERT (0 ); +DC_LOG_HW_LINK_TRAINING ("%s: Invalid HW Training pattern: %d\n" , + __func__, pattern); +break ; + } +return disable_scrabled_data_symbols; +} +static inline bool is_repeater (struct dc_link *link,uint32_t offset) {return (!link->is_lttpr_mode_transparent && offset !=0 );
@@ -251,6 +275,9 @@ static void dpcd_set_lt_pattern_and_lane_settings( dpcd_pattern.v1_4.TRAINING_PATTERN_SET =dc_dp_training_pattern_to_dpcd_training_pattern (link, pattern); + dpcd_pattern.v1_4.SCRAMBLING_DISABLE = +dc_dp_initialize_scrambling_data_symbols (link, pattern); + dpcd_lt_buffer[DP_TRAINING_PATTERN_SET -DP_TRAINING_PATTERN_SET ] = dpcd_pattern.raw;
Signature · 6 lines
2.26.2 _______________________________________________ amd-gfx mailing list [email protected] https://lists.freedesktop.org/mailman/listinfo/amd-gfx
PATCH 6/27 drm/amd/display: Check bss_data_size before going down legacy DMUB load path
In reply to Rodrigo SiqueiraFrom: Nicholas Kazlauskas <[email protected]>
[Why]
New unified firmware binary with only inst const still passes down fw_bss_data != NULL and params->bss_data_size == 0 from DM.
This leads it into the legacy path causing firmware state allocation to be too small.
[How]
Check bss_data_size as well.
--- drivers/gpu/drm/amd/display/dmub/src/dmub_srv.c | 4 ++-- 1 file changed, 2 insertions(+), 2 deletions(-)
drivers/gpu/drm/amd/display/dmub/src/dmub_srv.c +2 -2
@@ -98,12 +98,12 @@ dmub_get_fw_meta_info(const struct dmub_srv_region_params *params)uint32_t blob_size =0 ;uint32_t meta_offset =0 ; -if (params->fw_bss_data) { +if (params->fw_bss_data && params->bss_data_size) {/* Legacy metadata region. */ blob = params->fw_bss_data; blob_size = params->bss_data_size; meta_offset =DMUB_FW_META_OFFSET ; - }else if (params->fw_inst_const) { + }else if (params->fw_inst_const && params->inst_const_size) {/* Combined metadata region. */ blob = params->fw_inst_const; blob_size = params->inst_const_size;
Signature · 6 lines
2.26.2 _______________________________________________ amd-gfx mailing list [email protected] https://lists.freedesktop.org/mailman/listinfo/amd-gfx
PATCH 7/27 drm/amd/display: Don't pass invalid fw_bss_data pointer into DMUB srv
In reply to Rodrigo SiqueiraFrom: Nicholas Kazlauskas <[email protected]>
[Why]
If bss_data_size is 0 then we shouldn't be passing down fw_bss_data into the DMUB service since the region isn't really "valid."
[How]
Pass NULL instead if the size is 0.
--- drivers/gpu/drm/amd/display/amdgpu_dm/amdgpu_dm.c | 4 ++-- 1 file changed, 2 insertions(+), 2 deletions(-)
drivers/gpu/drm/amd/display/amdgpu_dm/amdgpu_dm.c +2 -2
@@ -1211,10 +1211,10 @@ static int dm_dmub_sw_init(struct amdgpu_device *adev)PSP_HEADER_BYTES -PSP_FOOTER_BYTES ; region_params.bss_data_size =le32_to_cpu (hdr->bss_data_bytes); region_params.vbios_size = adev->bios_size; - region_params.fw_bss_data = + region_params.fw_bss_data = region_params.bss_data_size ? adev->dm.dmub_fw->data +le32_to_cpu (hdr->header.ucode_array_offset_bytes) + -le32_to_cpu (hdr->inst_const_bytes); +le32_to_cpu (hdr->inst_const_bytes) :NULL ; region_params.fw_inst_const = adev->dm.dmub_fw->data + le32_to_cpu(hdr->header.ucode_array_offset_bytes) +
Signature · 6 lines
2.26.2 _______________________________________________ amd-gfx mailing list [email protected] https://lists.freedesktop.org/mailman/listinfo/amd-gfx
PATCH 8/27 drm/amd/display: Add bit swap helper based on endianness
In reply to Rodrigo SiqueiraChristian Koenig pointed out a code duplication related to bit swap in case of big-endian manipulation. This commit adds a helper for handling this verification and reduces the requirement of replicate some part of the code.
--- .../amd/display/modules/power/power_helpers.c | 50 ++++++++++--------- 1 file changed, 26 insertions(+), 24 deletions(-)
drivers/gpu/drm/amd/display/modules/power/power_helpers.c +26 -24
@@ -29,6 +29,8 @@#include "core_types.h" #define DIV_ROUNDUP (a, b) (((a)+((b)/2))/(b)) +#define bswap16_based_on_endian (big_endian, value) \ + (big_endian) ? cpu_to_be16(value) : cpu_to_le16(value)/* Possible Min Reduction config from least aggressive to most aggressive * 0 1 2 3 4 5 6 7 8 9 10 11 12
@@ -624,30 +626,30 @@ void fill_iram_v_2_3(struct iram_table_v_2_2 *ram_table, struct dmcu_iram_parame ram_table->iir_curve[4 ] =0x65 ;//Gamma 2.2 - ram_table->crgb_thresh[0 ] = (big_endian) ?cpu_to_be16 (0x127c ) :cpu_to_le16 (0x127c ); - ram_table->crgb_thresh[1 ] = (big_endian) ?cpu_to_be16 (0x151b ) :cpu_to_le16 (0x151b ); - ram_table->crgb_thresh[2 ] = (big_endian) ?cpu_to_be16 (0x17d5 ) :cpu_to_le16 (0x17d5 ); - ram_table->crgb_thresh[3 ] = (big_endian) ?cpu_to_be16 (0x1a56 ) :cpu_to_le16 (0x1a56 ); - ram_table->crgb_thresh[4 ] = (big_endian) ?cpu_to_be16 (0x1c83 ) :cpu_to_le16 (0x1c83 ); - ram_table->crgb_thresh[5 ] = (big_endian) ?cpu_to_be16 (0x1e72 ) :cpu_to_le16 (0x1e72 ); - ram_table->crgb_thresh[6 ] = (big_endian) ?cpu_to_be16 (0x20f0 ) :cpu_to_le16 (0x20f0 ); - ram_table->crgb_thresh[7 ] = (big_endian) ?cpu_to_be16 (0x232b ) :cpu_to_le16 (0x232b ); - ram_table->crgb_offset[0 ] = (big_endian) ?cpu_to_be16 (0x2999 ) :cpu_to_le16 (0x2999 ); - ram_table->crgb_offset[1 ] = (big_endian) ?cpu_to_be16 (0x3999 ) :cpu_to_le16 (0x3999 ); - ram_table->crgb_offset[2 ] = (big_endian) ?cpu_to_be16 (0x4666 ) :cpu_to_le16 (0x4666 ); - ram_table->crgb_offset[3 ] = (big_endian) ?cpu_to_be16 (0x5999 ) :cpu_to_le16 (0x5999 ); - ram_table->crgb_offset[4 ] = (big_endian) ?cpu_to_be16 (0x6333 ) :cpu_to_le16 (0x6333 ); - ram_table->crgb_offset[5 ] = (big_endian) ?cpu_to_be16 (0x7800 ) :cpu_to_le16 (0x7800 ); - ram_table->crgb_offset[6 ] = (big_endian) ?cpu_to_be16 (0x8c00 ) :cpu_to_le16 (0x8c00 ); - ram_table->crgb_offset[7 ] = (big_endian) ?cpu_to_be16 (0xa000 ) :cpu_to_le16 (0xa000 ); - ram_table->crgb_slope[0 ] = (big_endian) ?cpu_to_be16 (0x3609 ) :cpu_to_le16 (0x3609 ); - ram_table->crgb_slope[1 ] = (big_endian) ?cpu_to_be16 (0x2dfa ) :cpu_to_le16 (0x2dfa ); - ram_table->crgb_slope[2 ] = (big_endian) ?cpu_to_be16 (0x27ea ) :cpu_to_le16 (0x27ea ); - ram_table->crgb_slope[3 ] = (big_endian) ?cpu_to_be16 (0x235d ) :cpu_to_le16 (0x235d ); - ram_table->crgb_slope[4 ] = (big_endian) ?cpu_to_be16 (0x2042 ) :cpu_to_le16 (0x2042 ); - ram_table->crgb_slope[5 ] = (big_endian) ?cpu_to_be16 (0x1dc3 ) :cpu_to_le16 (0x1dc3 ); - ram_table->crgb_slope[6 ] = (big_endian) ?cpu_to_be16 (0x1b1a ) :cpu_to_le16 (0x1b1a ); - ram_table->crgb_slope[7 ] = (big_endian) ?cpu_to_be16 (0x1910 ) :cpu_to_le16 (0x1910 ); + ram_table->crgb_thresh[0 ] =bswap16_based_on_endian (big_endian,0x127c ); + ram_table->crgb_thresh[1 ] =bswap16_based_on_endian (big_endian,0x151b ); + ram_table->crgb_thresh[2 ] =bswap16_based_on_endian (big_endian,0x17d5 ); + ram_table->crgb_thresh[3 ] =bswap16_based_on_endian (big_endian,0x1a56 ); + ram_table->crgb_thresh[4 ] =bswap16_based_on_endian (big_endian,0x1c83 ); + ram_table->crgb_thresh[5 ] =bswap16_based_on_endian (big_endian,0x1e72 ); + ram_table->crgb_thresh[6 ] =bswap16_based_on_endian (big_endian,0x20f0 ); + ram_table->crgb_thresh[7 ] =bswap16_based_on_endian (big_endian,0x232b ); + ram_table->crgb_offset[0 ] =bswap16_based_on_endian (big_endian,0x2999 ); + ram_table->crgb_offset[1 ] =bswap16_based_on_endian (big_endian,0x3999 ); + ram_table->crgb_offset[2 ] =bswap16_based_on_endian (big_endian,0x4666 ); + ram_table->crgb_offset[3 ] =bswap16_based_on_endian (big_endian,0x5999 ); + ram_table->crgb_offset[4 ] =bswap16_based_on_endian (big_endian,0x6333 ); + ram_table->crgb_offset[5 ] =bswap16_based_on_endian (big_endian,0x7800 ); + ram_table->crgb_offset[6 ] =bswap16_based_on_endian (big_endian,0x8c00 ); + ram_table->crgb_offset[7 ] =bswap16_based_on_endian (big_endian,0xa000 ); + ram_table->crgb_slope[0 ] =bswap16_based_on_endian (big_endian,0x3609 ); + ram_table->crgb_slope[1 ] =bswap16_based_on_endian (big_endian,0x2dfa ); + ram_table->crgb_slope[2 ] =bswap16_based_on_endian (big_endian,0x27ea ); + ram_table->crgb_slope[3 ] =bswap16_based_on_endian (big_endian,0x235d ); + ram_table->crgb_slope[4 ] =bswap16_based_on_endian (big_endian,0x2042 ); + ram_table->crgb_slope[5 ] =bswap16_based_on_endian (big_endian,0x1dc3 ); + ram_table->crgb_slope[6 ] =bswap16_based_on_endian (big_endian,0x1b1a ); + ram_table->crgb_slope[7 ] =bswap16_based_on_endian (big_endian,0x1910 );fill_backlight_transform_table_v_2_2 ( params, ram_table, big_endian);
Signature · 6 lines
2.26.2 _______________________________________________ amd-gfx mailing list [email protected] https://lists.freedesktop.org/mailman/listinfo/amd-gfx
PATCH 9/27 drm/amd/display: Implement some asic specific abm call backs.
In reply to Rodrigo SiqueiraFrom: Yongqiang Sun <[email protected]>
[Why & How]
Implement abm set_pipe call stacks
Have some asics speicifc call stacks for abm.
--- drivers/gpu/drm/amd/display/dc/dce/dmub_abm.c | 92 ------------------- .../display/dc/dce110/dce110_hw_sequencer.c | 11 +++ .../display/dc/dce110/dce110_hw_sequencer.h | 1 + .../amd/display/dc/dcn10/dcn10_hw_sequencer.c | 3 +- .../gpu/drm/amd/display/dc/dcn10/dcn10_init.c | 1 + .../drm/amd/display/dc/dcn20/dcn20_hwseq.c | 3 +- .../gpu/drm/amd/display/dc/dcn20/dcn20_init.c | 1 + .../drm/amd/display/dc/dcn21/dcn21_hwseq.c | 89 ++++++++++++++++++ .../drm/amd/display/dc/dcn21/dcn21_hwseq.h | 6 ++ .../gpu/drm/amd/display/dc/dcn21/dcn21_init.c | 5 +- .../gpu/drm/amd/display/dc/inc/hw_sequencer.h | 2 + .../gpu/drm/amd/display/dmub/inc/dmub_cmd.h | 4 + 12 files changed, 120 insertions(+), 98 deletions(-)
drivers/gpu/drm/amd/display/dc/dce/dmub_abm.c +0 -92
@@ -50,71 +50,7 @@#define DISABLE_ABM_IMMEDIATELY 255 -static bool dmub_abm_set_pipe (struct abm *abm,uint32_t otg_inst,uint32_t panel_inst) -{ -union dmub_rb_cmd cmd; -struct dc_context *dc = abm->ctx; -uint32_t ramping_boundary =0xFFFF ; - - cmd.abm_set_pipe.header.type =DMUB_CMD__ABM ; - cmd.abm_set_pipe.header.sub_type =DMUB_CMD__ABM_SET_PIPE ; - cmd.abm_set_pipe.abm_set_pipe_data.otg_inst = otg_inst; - cmd.abm_set_pipe.abm_set_pipe_data.panel_inst = panel_inst; - cmd.abm_set_pipe.abm_set_pipe_data.ramping_boundary = ramping_boundary; - cmd.abm_set_pipe.header.payload_bytes =sizeof (struct dmub_cmd_abm_set_pipe_data ); - -dc_dmub_srv_cmd_queue (dc->dmub_srv, &cmd); -dc_dmub_srv_cmd_execute (dc->dmub_srv); -dc_dmub_srv_wait_idle (dc->dmub_srv); - -return true; -} - -static void dmcub_set_backlight_level ( -struct dce_abm *dce_abm, -uint32_t backlight_pwm_u16_16, -uint32_t frame_ramp, -uint32_t otg_inst, -uint32_t panel_inst) -{ -union dmub_rb_cmd cmd; -struct dc_context *dc = dce_abm->base.ctx; -unsigned int backlight_8_bit =0 ; -uint32_t s2; - -if (backlight_pwm_u16_16 &0x10000 ) -// Check for max backlight condition - backlight_8_bit =0xFF ; -else -// Take MSB of fractional part since backlight is not max - backlight_8_bit = (backlight_pwm_u16_16 >>8 ) &0xFF ; - -dmub_abm_set_pipe (&dce_abm->base, otg_inst, panel_inst); - -REG_UPDATE (BL1_PWM_USER_LEVEL ,BL1_PWM_USER_LEVEL , backlight_pwm_u16_16); - -if (otg_inst ==0 ) - frame_ramp =0 ; - - cmd.abm_set_backlight.header.type =DMUB_CMD__ABM ; - cmd.abm_set_backlight.header.sub_type =DMUB_CMD__ABM_SET_BACKLIGHT ; - cmd.abm_set_backlight.abm_set_backlight_data.frame_ramp = frame_ramp; - cmd.abm_set_backlight.header.payload_bytes =sizeof (struct dmub_cmd_abm_set_backlight_data ); -dc_dmub_srv_cmd_queue (dc->dmub_srv, &cmd); -dc_dmub_srv_cmd_execute (dc->dmub_srv); -dc_dmub_srv_wait_idle (dc->dmub_srv); - -// Update requested backlight level - s2 =REG_READ (BIOS_SCRATCH_2 ); - - s2 &= ~ATOM_S2_CURRENT_BL_LEVEL_MASK ; - backlight_8_bit &= (ATOM_S2_CURRENT_BL_LEVEL_MASK >> -ATOM_S2_CURRENT_BL_LEVEL_SHIFT ); - s2 |= (backlight_8_bit <<ATOM_S2_CURRENT_BL_LEVEL_SHIFT ); - -REG_WRITE (BIOS_SCRATCH_2 , s2); -}static void dmub_abm_enable_fractional_pwm (struct dc_context *dc) {
@@ -211,31 +147,6 @@ static bool dmub_abm_set_level(struct abm *abm, uint32_t level)return true; } -static bool dmub_abm_immediate_disable (struct abm *abm,uint32_t panel_inst) -{ -dmub_abm_set_pipe (abm,DISABLE_ABM_IMMEDIATELY , panel_inst); - -return true; -} - -static bool dmub_abm_set_backlight_level_pwm ( -struct abm *abm, -unsigned int backlight_pwm_u16_16, -unsigned int frame_ramp, -unsigned int otg_inst, -uint32_t panel_inst) -{ -struct dce_abm *dce_abm =TO_DMUB_ABM (abm); - -dmcub_set_backlight_level (dce_abm, - backlight_pwm_u16_16, - frame_ramp, - otg_inst, - panel_inst); - -return true; -} -static bool dmub_abm_init_config (struct abm *abm,const char *src,unsigned int bytes)
@@ -266,11 +177,8 @@ static bool dmub_abm_init_config(struct abm *abm,static const struct abm_funcs abm_funcs = { .abm_init = dmub_abm_init, .set_abm_level = dmub_abm_set_level, - .set_pipe = dmub_abm_set_pipe, - .set_backlight_level_pwm = dmub_abm_set_backlight_level_pwm, .get_current_backlight = dmub_abm_get_current_backlight, .get_target_backlight = dmub_abm_get_target_backlight, - .set_abm_immediate_disable = dmub_abm_immediate_disable, .init_abm_config = dmub_abm_init_config, };
drivers/gpu/drm/amd/display/dc/dce110/dce110_hw_sequencer.c +11 -0
@@ -2767,6 +2767,16 @@ void dce110_set_abm_immediate_disable(struct pipe_ctx *pipe_ctx) panel_cntl->funcs->store_backlight_level (panel_cntl); } +void dce110_set_pipe (struct pipe_ctx *pipe_ctx) +{ +struct abm *abm = pipe_ctx->stream_res.abm; +struct panel_cntl *panel_cntl = pipe_ctx->stream->link->panel_cntl; +uint32_t otg_inst = pipe_ctx->stream_res.tg->inst +1 ; + +if (abm && panel_cntl) + abm->funcs->set_pipe (abm, otg_inst, panel_cntl->inst); +} +static const struct hw_sequencer_funcs dce110_funcs = { .program_gamut_remap = program_gamut_remap, .program_output_csc = program_output_csc,
@@ -2804,6 +2814,7 @@ static const struct hw_sequencer_funcs dce110_funcs = { .set_cursor_attribute = dce110_set_cursor_attribute, .set_backlight_level = dce110_set_backlight_level, .set_abm_immediate_disable = dce110_set_abm_immediate_disable, + .set_pipe = dce110_set_pipe, };static const struct hwseq_private_funcs dce110_private_funcs = {
drivers/gpu/drm/amd/display/dc/dce110/dce110_hw_sequencer.h +1 -0
@@ -89,6 +89,7 @@ bool dce110_set_backlight_level(struct pipe_ctx *pipe_ctx,uint32_t backlight_pwm_u16_16, uint32_t frame_ramp);void dce110_set_abm_immediate_disable (struct pipe_ctx *pipe_ctx); +void dce110_set_pipe (struct pipe_ctx *pipe_ctx);#endif /* __DC_HWSS_DCE110_H__ */
drivers/gpu/drm/amd/display/dc/dcn10/dcn10_hw_sequencer.c +1 -2
@@ -2506,8 +2506,7 @@ void dcn10_blank_pixel_data(if (stream_res->tg->funcs->set_blank) stream_res->tg->funcs->set_blank (stream_res->tg, blank);if (stream_res->abm) { - stream_res->abm->funcs->set_pipe (stream_res->abm, stream_res->tg->inst +1 , - stream->link->panel_cntl->inst); + dc->hwss.set_pipe (pipe_ctx); stream_res->abm->funcs->set_abm_level (stream_res->abm, stream->abm_level); } }else if (blank) {
drivers/gpu/drm/amd/display/dc/dcn10/dcn10_init.c +1 -0
@@ -74,6 +74,7 @@ static const struct hw_sequencer_funcs dcn10_funcs = { .get_vupdate_offset_from_vsync = dcn10_get_vupdate_offset_from_vsync, .set_backlight_level = dce110_set_backlight_level, .set_abm_immediate_disable = dce110_set_abm_immediate_disable, + .set_pipe = dce110_set_pipe, };static const struct hwseq_private_funcs dcn10_private_funcs = {
drivers/gpu/drm/amd/display/dc/dcn20/dcn20_hwseq.c +1 -2
@@ -996,8 +996,7 @@ void dcn20_blank_pixel_data(if (!blank)if (stream_res->abm) { - stream_res->abm->funcs->set_pipe (stream_res->abm, stream_res->tg->inst +1 , - stream->link->panel_cntl->inst); + dc->hwss.set_pipe (pipe_ctx); stream_res->abm->funcs->set_abm_level (stream_res->abm, stream->abm_level); } }
drivers/gpu/drm/amd/display/dc/dcn20/dcn20_init.c +1 -0
@@ -85,6 +85,7 @@ static const struct hw_sequencer_funcs dcn20_funcs = { .get_vupdate_offset_from_vsync = dcn10_get_vupdate_offset_from_vsync, .set_backlight_level = dce110_set_backlight_level, .set_abm_immediate_disable = dce110_set_abm_immediate_disable, + .set_pipe = dce110_set_pipe, };static const struct hwseq_private_funcs dcn20_private_funcs = {
drivers/gpu/drm/amd/display/dc/dcn21/dcn21_hwseq.c +89 -0
102 lines not on this page · raw message
drivers/gpu/drm/amd/display/dc/dcn21/dcn21_hwseq.h +6 -0
@@ -47,4 +47,10 @@ void dcn21_optimize_pwr_state(void dcn21_PLAT_58856_wa (struct dc_state *context,struct pipe_ctx *pipe_ctx); +void dcn21_set_pipe (struct pipe_ctx *pipe_ctx); +void dcn21_set_abm_immediate_disable (struct pipe_ctx *pipe_ctx); +bool dcn21_set_backlight_level (struct pipe_ctx *pipe_ctx, +uint32_t backlight_pwm_u16_16, +uint32_t frame_ramp); +#endif /* __DC_HWSS_DCN21_H__ */
drivers/gpu/drm/amd/display/dc/dcn21/dcn21_init.c +3 -2
@@ -87,8 +87,9 @@ static const struct hw_sequencer_funcs dcn21_funcs = { .exit_optimized_pwr_state = dcn21_exit_optimized_pwr_state, .get_vupdate_offset_from_vsync = dcn10_get_vupdate_offset_from_vsync, .power_down = dce110_power_down, - .set_backlight_level = dce110_set_backlight_level, - .set_abm_immediate_disable = dce110_set_abm_immediate_disable, + .set_backlight_level = dcn21_set_backlight_level, + .set_abm_immediate_disable = dcn21_set_abm_immediate_disable, + .set_pipe = dcn21_set_pipe, };static const struct hwseq_private_funcs dcn21_private_funcs = {
drivers/gpu/drm/amd/display/dc/inc/hw_sequencer.h +2 -0
@@ -198,6 +198,8 @@ struct hw_sequencer_funcs {void (*set_abm_immediate_disable)(struct pipe_ctx *pipe_ctx); +void (*set_pipe)(struct pipe_ctx *pipe_ctx); + };
drivers/gpu/drm/amd/display/dmub/inc/dmub_cmd.h +4 -0
@@ -36,6 +36,9 @@#define DMUB_RB_SIZE (DMUB_RB_CMD_SIZE * DMUB_RB_MAX_ENTRY)#define REG_SET_MASK 0xFFFF +#define SET_ABM_PIPE_GRADUALLY_DISABLE 0 +#define SET_ABM_PIPE_IMMEDIATELY_DISABLE 255 +#define SET_ABM_PIPE_NORMAL 1/* * Command IDs should be treated as stable ABI.
@@ -272,6 +275,7 @@ struct dmub_rb_cmd_abm_set_pipe {struct dmub_cmd_abm_set_backlight_data {uint32_t frame_ramp; +uint32_t backlight_user_level; };struct dmub_rb_cmd_abm_set_backlight {
Signature · 6 lines
2.26.2 _______________________________________________ amd-gfx mailing list [email protected] https://lists.freedesktop.org/mailman/listinfo/amd-gfx
PATCH 10/27 drm/amd/display: FW release 1.0.10
In reply to Rodrigo SiqueiraFrom: Anthony Koo <[email protected]>
--- drivers/gpu/drm/amd/display/dc/dce/dmub_psr.c | 2 +- .../gpu/drm/amd/display/dmub/inc/dmub_cmd.h | 12 ++++--- .../drm/amd/display/dmub/inc/dmub_cmd_dal.h | 35 +++++++++++++++++++ .../gpu/drm/amd/display/dmub/inc/dmub_types.h | 9 +++-- 4 files changed, 49 insertions(+), 9 deletions(-)
drivers/gpu/drm/amd/display/dc/dce/dmub_psr.c +1 -1
@@ -231,7 +231,7 @@ static bool dmub_psr_copy_settings(struct dmub_psr *dmub, copy_settings_data->smu_optimizations_en = psr_context->allow_smu_optimizations; copy_settings_data->frame_delay = psr_context->frame_delay; copy_settings_data->frame_cap_ind = psr_context->psrFrameCaptureIndicationReq; - copy_settings_data->debug.visual_confirm = dc->dc->debug.visual_confirm ==VISUAL_CONFIRM_PSR ? + copy_settings_data->debug.bitfields.visual_confirm = dc->dc->debug.visual_confirm ==VISUAL_CONFIRM_PSR ? true : false;dc_dmub_srv_cmd_queue (dc->dmub_srv, &cmd);
drivers/gpu/drm/amd/display/dmub/inc/dmub_cmd.h +7 -5
@@ -219,6 +219,7 @@ struct dmub_rb_cmd_dpphy_init { };struct dmub_cmd_psr_copy_settings_data { +union dmub_psr_debug_flags debug;uint16_t psr_level;uint8_t dpp_inst;uint8_t mpcc_inst;
@@ -231,7 +232,7 @@ struct dmub_cmd_psr_copy_settings_data {uint8_t smu_optimizations_en;uint8_t frame_delay;uint8_t frame_cap_ind; -struct dmub_psr_debug_flags debug; +uint8_t pad[3 ]; };struct dmub_rb_cmd_psr_copy_settings {
@@ -241,6 +242,7 @@ struct dmub_rb_cmd_psr_copy_settings {struct dmub_cmd_psr_set_level_data {uint16_t psr_level; +uint8_t pad[2 ]; };struct dmub_rb_cmd_psr_set_level {
@@ -262,10 +264,10 @@ struct dmub_rb_cmd_psr_set_version { };struct dmub_cmd_abm_set_pipe_data { -uint32_t ramping_boundary; -uint32_t otg_inst; -uint32_t panel_inst; -uint32_t set_pipe_option; +uint8_t otg_inst; +uint8_t panel_inst; +uint8_t set_pipe_option; +uint8_t ramping_boundary;// TODO: Remove this };struct dmub_rb_cmd_abm_set_pipe {
drivers/gpu/drm/amd/display/dmub/inc/dmub_cmd_dal.h +35 -0
@@ -26,6 +26,11 @@#ifndef _DMUB_CMD_DAL_H_#define _DMUB_CMD_DAL_H_ +#define NUM_AMBI_LEVEL 5 +#define NUM_AGGR_LEVEL 4 +#define NUM_POWER_FN_SEGS 8 +#define NUM_BL_CURVE_SEGS 16 +/* * Command IDs should be treated as stable ABI. * Do not reuse or modify IDs.
@@ -53,4 +58,34 @@ enum dmub_cmd_abm_type { DMUB_CMD__ABM_SET_PWM_FRAC = 5, }; +/* +* Parameters for ABM2.4 algorithm. +* Padded explicitly to 32-bit boundary. +*/ +struct abm_config_table { +/* Parameters for crgb conversion */ +uint16_t crgb_thresh[NUM_POWER_FN_SEGS ];// 0B +uint16_t crgb_offset[NUM_POWER_FN_SEGS ];// 15B +uint16_t crgb_slope[NUM_POWER_FN_SEGS ];// 31B + +/* Parameters for custom curve */ +uint16_t backlight_thresholds[NUM_BL_CURVE_SEGS ];// 47B +uint16_t backlight_offsets[NUM_BL_CURVE_SEGS ];// 79B + +uint16_t ambient_thresholds_lux[NUM_AMBI_LEVEL ];// 111B +uint16_t min_abm_backlight;// 121B + +uint8_t min_reduction[NUM_AMBI_LEVEL ][NUM_AGGR_LEVEL ];// 123B +uint8_t max_reduction[NUM_AMBI_LEVEL ][NUM_AGGR_LEVEL ];// 143B +uint8_t bright_pos_gain[NUM_AMBI_LEVEL ][NUM_AGGR_LEVEL ];// 163B +uint8_t dark_pos_gain[NUM_AMBI_LEVEL ][NUM_AGGR_LEVEL ];// 183B +uint8_t hybrid_factor[NUM_AGGR_LEVEL ];// 203B +uint8_t contrast_factor[NUM_AGGR_LEVEL ];// 207B +uint8_t deviation_gain[NUM_AGGR_LEVEL ];// 211B +uint8_t min_knee[NUM_AGGR_LEVEL ];// 215B +uint8_t max_knee[NUM_AGGR_LEVEL ];// 219B +uint8_t iir_curve[NUM_AMBI_LEVEL ];// 223B +uint8_t pad3[3 ];// 228B +}; +#endif /* _DMUB_CMD_DAL_H_ */
drivers/gpu/drm/amd/display/dmub/inc/dmub_types.h +6 -3
@@ -63,9 +63,12 @@ union dmub_addr {uint64_t quad_part; }; -struct dmub_psr_debug_flags { -uint8_t visual_confirm :1 ; -uint8_t reserved :7 ; +union dmub_psr_debug_flags { +struct { +uint8_t visual_confirm :1 ; + } bitfields; + +unsigned int u32All; };#if defined(__cplusplus)
Signature · 6 lines
2.26.2 _______________________________________________ amd-gfx mailing list [email protected] https://lists.freedesktop.org/mailman/listinfo/amd-gfx
PATCH 11/27 drm/amd/display: Fix ABM memory alignment issue
In reply to Rodrigo SiqueiraFrom: Wyatt Wood <[email protected]>
[Why]
Due to packing of abm_config_table, memory addresses aren't aligned to 32 bit boundary dmcub prefers. Therefore when using pointers to this structure, it's possible that dmcub will automatically align the data read from that address, yielding incorrect values.
[How]
Instead of packing 1 byte boundary, explicitly pack values to 4 byte boundary. Since there is a dependency on the existing iram table structure on driver side, we must copy to a second structure, which is aligned correctly, before passing to fw.
--- .../amd/display/modules/power/power_helpers.c | 45 +++++++++++++++++-- 1 file changed, 42 insertions(+), 3 deletions(-)
drivers/gpu/drm/amd/display/modules/power/power_helpers.c +42 -3
@@ -27,6 +27,7 @@#include "dc/inc/hw/abm.h" #include "dc.h" #include "core_types.h" +#include "dmub_cmd_dal.h" #define DIV_ROUNDUP (a, b) (((a)+((b)/2))/(b))#define bswap16_based_on_endian (big_endian, value) \
@@ -658,17 +659,55 @@ void fill_iram_v_2_3(struct iram_table_v_2_2 *ram_table, struct dmcu_iram_paramebool dmub_init_abm_config (struct abm *abm,struct dmcu_iram_parameters params) { -unsigned char ram_table[IRAM_SIZE ]; +struct iram_table_v_2_2 ram_table; +struct abm_config_table config;bool result = false; +uint32_t i, j =0 ;if (abm ==NULL )return false;memset (&ram_table,0 ,sizeof (ram_table)); +memset (&config,0 ,sizeof (config)); + +fill_iram_v_2_3 (&ram_table, params, false); + +// We must copy to structure that is aligned to 32-bit +for (i =0 ; i <NUM_POWER_FN_SEGS ; i++) { + config.crgb_thresh[i] = ram_table.crgb_thresh[i]; + config.crgb_offset[i] = ram_table.crgb_offset[i]; + config.crgb_slope[i] = ram_table.crgb_slope[i]; + } + +for (i =0 ; i <NUM_BL_CURVE_SEGS ; i++) { + config.backlight_thresholds[i] = ram_table.backlight_thresholds[i]; + config.backlight_offsets[i] = ram_table.backlight_offsets[i]; + } + +for (i =0 ; i <NUM_AMBI_LEVEL ; i++) + config.iir_curve[i] = ram_table.iir_curve[i]; + +for (i =0 ; i <NUM_AMBI_LEVEL ; i++) { +for (j =0 ; j <NUM_AGGR_LEVEL ; j++) { + config.min_reduction[i][j] = ram_table.min_reduction[i][j]; + config.max_reduction[i][j] = ram_table.max_reduction[i][j]; + config.bright_pos_gain[i][j] = ram_table.bright_pos_gain[i][j]; + config.dark_pos_gain[i][j] = ram_table.dark_pos_gain[i][j]; + } + } + +for (i =0 ; i <NUM_AGGR_LEVEL ; i++) { + config.hybrid_factor[i] = ram_table.hybrid_factor[i]; + config.contrast_factor[i] = ram_table.contrast_factor[i]; + config.deviation_gain[i] = ram_table.deviation_gain[i]; + config.min_knee[i] = ram_table.min_knee[i]; + config.max_knee[i] = ram_table.max_knee[i]; + } + + config.min_abm_backlight = ram_table.min_abm_backlight; -fill_iram_v_2_3 ((struct iram_table_v_2_2 *)ram_table, params, false); result = abm->funcs->init_abm_config ( - abm, (char *)(&ram_table),IRAM_RESERVE_AREA_START_V2_2 ); + abm, (char *)(&config),sizeof (struct abm_config_table ));return result; }
Signature · 6 lines
2.26.2 _______________________________________________ amd-gfx mailing list [email protected] https://lists.freedesktop.org/mailman/listinfo/amd-gfx
PATCH 12/27 drm/amd/display: 3.2.85
In reply to Rodrigo SiqueiraFrom: Aric Cyr <[email protected]>
--- drivers/gpu/drm/amd/display/dc/dc.h | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-)
drivers/gpu/drm/amd/display/dc/dc.h +1 -1
@@ -42,7 +42,7 @@#include "inc/hw/dmcu.h" #include "dml/display_mode_lib.h" -#define DC_VER "3.2.84" +#define DC_VER "3.2.85"#define MAX_SURFACES 3#define MAX_PLANES 6
Signature · 6 lines
2.26.2 _______________________________________________ amd-gfx mailing list [email protected] https://lists.freedesktop.org/mailman/listinfo/amd-gfx
PATCH 13/27 drm/amd/display: Remove dml_common_def file
In reply to Rodrigo SiqueiraDuring the rework for removing the FPU issues, I found the following warning:
[..] dml_common_defs.o: warning: objtool: dml_round()+0x9: FPU
instruction outside of kernel_fpu_{begin,end}()
This file has a single function that does not need to be in a specific file. This commit drop dml_common_defs file, and move dml_round function to dml_inline_defs.
--- drivers/gpu/drm/amd/display/dc/dml/Makefile | 2 - .../dc/dml/dcn20/display_rq_dlg_calc_20.h | 1 - .../dc/dml/dcn20/display_rq_dlg_calc_20v2.h | 1 - .../dc/dml/dcn21/display_rq_dlg_calc_21.h | 2 +- .../drm/amd/display/dc/dml/display_mode_lib.h | 6 ++- .../drm/amd/display/dc/dml/display_mode_vba.h | 2 - .../display/dc/dml/display_rq_dlg_helpers.h | 1 - .../display/dc/dml/dml1_display_rq_dlg_calc.h | 2 - .../drm/amd/display/dc/dml/dml_common_defs.c | 43 ------------------- .../drm/amd/display/dc/dml/dml_common_defs.h | 37 ---------------- .../drm/amd/display/dc/dml/dml_inline_defs.h | 15 ++++++- 11 files changed, 18 insertions(+), 94 deletions(-) delete mode 100644 drivers/gpu/drm/amd/display/dc/dml/dml_common_defs.c delete mode 100644 drivers/gpu/drm/amd/display/dc/dml/dml_common_defs.h
drivers/gpu/drm/amd/display/dc/dml/Makefile +0 -2
@@ -63,10 +63,8 @@ CFLAGS_$(AMDDALPATH)/dc/dml/dcn21/display_rq_dlg_calc_21.o := $(dml_ccflags) endif CFLAGS_$(AMDDALPATH)/dc/dml/dml1_display_rq_dlg_calc.o := $(dml_ccflags) CFLAGS_$(AMDDALPATH)/dc/dml/display_rq_dlg_helpers.o := $(dml_ccflags) -CFLAGS_$(AMDDALPATH)/dc/dml/dml_common_defs.o := $(dml_ccflags) DML = display_mode_lib.o display_rq_dlg_helpers.o dml1_display_rq_dlg_calc.o \ - dml_common_defs.o ifdef CONFIG_DRM_AMD_DC_DCN DML += display_mode_vba.o dcn20/display_rq_dlg_calc_20.o dcn20/display_mode_vba_20.o
drivers/gpu/drm/amd/display/dc/dml/dcn20/display_rq_dlg_calc_20.h +0 -1
@@ -26,7 +26,6 @@#ifndef __DML20_DISPLAY_RQ_DLG_CALC_H__#define __DML20_DISPLAY_RQ_DLG_CALC_H__ -#include "../dml_common_defs.h" #include "../display_rq_dlg_helpers.h" struct display_mode_lib ;
drivers/gpu/drm/amd/display/dc/dml/dcn20/display_rq_dlg_calc_20v2.h +0 -1
@@ -26,7 +26,6 @@#ifndef __DML20V2_DISPLAY_RQ_DLG_CALC_H__#define __DML20V2_DISPLAY_RQ_DLG_CALC_H__ -#include "../dml_common_defs.h" #include "../display_rq_dlg_helpers.h" struct display_mode_lib ;
drivers/gpu/drm/amd/display/dc/dml/dcn21/display_rq_dlg_calc_21.h +1 -1
@@ -26,7 +26,7 @@#ifndef __DML21_DISPLAY_RQ_DLG_CALC_H__#define __DML21_DISPLAY_RQ_DLG_CALC_H__ -#include "../dml_common_defs.h" +#include "dm_services.h" #include "../display_rq_dlg_helpers.h" struct display_mode_lib ;
drivers/gpu/drm/amd/display/dc/dml/display_mode_lib.h +4 -2
@@ -25,8 +25,10 @@#ifndef __DISPLAY_MODE_LIB_H__#define __DISPLAY_MODE_LIB_H__ - -#include "dml_common_defs.h" +#include "dm_services.h" +#include "dc_features.h" +#include "display_mode_structs.h" +#include "display_mode_enums.h" #include "display_mode_vba.h" enum dml_project {
drivers/gpu/drm/amd/display/dc/dml/display_mode_vba.h +0 -2
@@ -27,8 +27,6 @@#ifndef __DML2_DISPLAY_MODE_VBA_H__#define __DML2_DISPLAY_MODE_VBA_H__ -#include "dml_common_defs.h" -struct display_mode_lib ;void ModeSupportAndSystemConfiguration (struct display_mode_lib *mode_lib);
drivers/gpu/drm/amd/display/dc/dml/display_rq_dlg_helpers.h +0 -1
@@ -26,7 +26,6 @@#ifndef __DISPLAY_RQ_DLG_HELPERS_H__#define __DISPLAY_RQ_DLG_HELPERS_H__ -#include "dml_common_defs.h" #include "display_mode_lib.h" /* Function: Printer functions
drivers/gpu/drm/amd/display/dc/dml/dml1_display_rq_dlg_calc.h +0 -2
@@ -26,8 +26,6 @@#ifndef __DISPLAY_RQ_DLG_CALC_H__#define __DISPLAY_RQ_DLG_CALC_H__ -#include "dml_common_defs.h" -struct display_mode_lib ;#include "display_rq_dlg_helpers.h"
drivers/gpu/drm/amd/display/dc/dml/dml_common_defs.c deleted +0 -43
43 lines not on this page · raw message
drivers/gpu/drm/amd/display/dc/dml/dml_common_defs.h deleted +0 -37
@@ -1,37 +0,0 @@ -/* -* Copyright 2017 Advanced Micro Devices, Inc. -* -* Permission is hereby granted, free of charge, to any person obtaining a -* copy of this software and associated documentation files (the "Software"), -* to deal in the Software without restriction, including without limitation -* the rights to use, copy, modify, merge, publish, distribute, sublicense, -* and/or sell copies of the Software, and to permit persons to whom the -* Software is furnished to do so, subject to the following conditions: -* -* The above copyright notice and this permission notice shall be included in -* all copies or substantial portions of the Software. -* -* THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, EXPRESS OR -* IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF MERCHANTABILITY, -* FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT. IN NO EVENT SHALL -* THE COPYRIGHT HOLDER(S) OR AUTHOR(S) BE LIABLE FOR ANY CLAIM, DAMAGES OR -* OTHER LIABILITY, WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, -* ARISING FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR -* OTHER DEALINGS IN THE SOFTWARE. -* -* Authors: AMD -* -*/ - -#ifndef __DC_COMMON_DEFS_H__ -#define __DC_COMMON_DEFS_H__ - -#include "dm_services.h" -#include "dc_features.h" -#include "display_mode_structs.h" -#include "display_mode_enums.h" - - -double dml_round (double a); - -#endif /* __DC_COMMON_DEFS_H__ */
drivers/gpu/drm/amd/display/dc/dml/dml_inline_defs.h +13 -2
@@ -26,7 +26,6 @@#ifndef __DML_INLINE_DEFS_H__#define __DML_INLINE_DEFS_H__ -#include "dml_common_defs.h" #include "dcn_calc_math.h" #include "dml_logger.h"
@@ -75,6 +74,18 @@ static inline double dml_floor(double a, double granularity)return (double )dcn_bw_floor2 (a, granularity); } +static inline double dml_round (double a) +{ +double round_pt =0.5 ; +double ceil =dml_ceil (a,1 ); +double floor =dml_floor (a,1 ); + +if (a - floor >= round_pt) +return ceil; +else +return floor; +} +static inline int dml_log2 (double x) {return dml_round ((double )dcn_bw_log (x,2 ));
@@ -112,7 +123,7 @@ static inline double dml_log(double x, double base)static inline unsigned int dml_round_to_multiple (unsigned int num,unsigned int multiple, -bool up) +unsigned char up) {unsigned int remainder;
Signature · 6 lines
2.26.2 _______________________________________________ amd-gfx mailing list [email protected] https://lists.freedesktop.org/mailman/listinfo/amd-gfx
PATCH 14/27 drm/amd/display: update dml interfaces and variables
In reply to Rodrigo SiqueiraFrom: Dmytro Laktyushkin <[email protected]>
Preparation for new asic support.
--- .../dc/dml/dcn20/display_rq_dlg_calc_20.c | 33 +-- .../dc/dml/dcn20/display_rq_dlg_calc_20v2.c | 33 +-- .../dc/dml/dcn21/display_rq_dlg_calc_21.c | 36 +-- .../amd/display/dc/dml/display_mode_enums.h | 8 +- .../amd/display/dc/dml/display_mode_structs.h | 11 + .../drm/amd/display/dc/dml/display_mode_vba.c | 54 +++-- .../drm/amd/display/dc/dml/display_mode_vba.h | 227 ++++++++++-------- 7 files changed, 186 insertions(+), 216 deletions(-)
drivers/gpu/drm/amd/display/dc/dml/dcn20/display_rq_dlg_calc_20.c +1 -32
@@ -890,11 +890,6 @@ static void dml20_rq_dlg_get_dlg_params(struct display_mode_lib *mode_lib,double refcyc_per_req_delivery_c;unsigned int full_recout_width; -double xfc_transfer_delay; -double xfc_precharge_delay; -double xfc_remote_surface_flip_latency; -double xfc_dst_y_delta_drq_limit; -double xfc_prefetch_margin;double refcyc_per_req_delivery_pre_cur0;double refcyc_per_req_delivery_cur0;double refcyc_per_req_delivery_pre_cur1;
@@ -1344,22 +1339,6 @@ static void dml20_rq_dlg_get_dlg_params(struct display_mode_lib *mode_lib,ASSERT (refcyc_per_req_delivery_c <dml_pow (2 ,13 )); } -// XFC - xfc_transfer_delay =get_xfc_transfer_delay (mode_lib, e2e_pipe_param, num_pipes, pipe_idx); - xfc_precharge_delay =get_xfc_precharge_delay (mode_lib, - e2e_pipe_param, - num_pipes, - pipe_idx); - xfc_remote_surface_flip_latency =get_xfc_remote_surface_flip_latency (mode_lib, - e2e_pipe_param, - num_pipes, - pipe_idx); - xfc_dst_y_delta_drq_limit = xfc_remote_surface_flip_latency; - xfc_prefetch_margin =get_xfc_prefetch_margin (mode_lib, - e2e_pipe_param, - num_pipes, - pipe_idx); -// TTU - Cursor refcyc_per_req_delivery_pre_cur0 =0.0 ; refcyc_per_req_delivery_cur0 =0.0 ;
@@ -1510,17 +1489,7 @@ static void dml20_rq_dlg_get_dlg_params(struct display_mode_lib *mode_lib, disp_dlg_regs->chunk_hdl_adjust_cur1 =3 ; disp_dlg_regs->dst_y_offset_cur1 =0 ; - disp_dlg_regs->xfc_reg_transfer_delay = xfc_transfer_delay; - disp_dlg_regs->xfc_reg_precharge_delay = xfc_precharge_delay; - disp_dlg_regs->xfc_reg_remote_surface_flip_latency = xfc_remote_surface_flip_latency; - disp_dlg_regs->xfc_reg_prefetch_margin =dml_ceil (xfc_prefetch_margin * refclk_freq_in_mhz, -1 ); - -// slave has to have this value also set to off -if (src->xfc_enable && !src->xfc_slave) - disp_dlg_regs->dst_y_delta_drq_limit =dml_ceil (xfc_dst_y_delta_drq_limit,1 ); -else - disp_dlg_regs->dst_y_delta_drq_limit =0x7fff ;// off + disp_dlg_regs->dst_y_delta_drq_limit =0x7fff ;// off disp_ttu_regs->refcyc_per_req_delivery_pre_l = (unsigned int ) (refcyc_per_req_delivery_pre_l *dml_pow (2 ,10 ));
drivers/gpu/drm/amd/display/dc/dml/dcn20/display_rq_dlg_calc_20v2.c +1 -32
@@ -890,11 +890,6 @@ static void dml20v2_rq_dlg_get_dlg_params(struct display_mode_lib *mode_lib,double refcyc_per_req_delivery_c;unsigned int full_recout_width; -double xfc_transfer_delay; -double xfc_precharge_delay; -double xfc_remote_surface_flip_latency; -double xfc_dst_y_delta_drq_limit; -double xfc_prefetch_margin;double refcyc_per_req_delivery_pre_cur0;double refcyc_per_req_delivery_cur0;double refcyc_per_req_delivery_pre_cur1;
@@ -1345,22 +1340,6 @@ static void dml20v2_rq_dlg_get_dlg_params(struct display_mode_lib *mode_lib,ASSERT (refcyc_per_req_delivery_c <dml_pow (2 ,13 )); } -// XFC - xfc_transfer_delay =get_xfc_transfer_delay (mode_lib, e2e_pipe_param, num_pipes, pipe_idx); - xfc_precharge_delay =get_xfc_precharge_delay (mode_lib, - e2e_pipe_param, - num_pipes, - pipe_idx); - xfc_remote_surface_flip_latency =get_xfc_remote_surface_flip_latency (mode_lib, - e2e_pipe_param, - num_pipes, - pipe_idx); - xfc_dst_y_delta_drq_limit = xfc_remote_surface_flip_latency; - xfc_prefetch_margin =get_xfc_prefetch_margin (mode_lib, - e2e_pipe_param, - num_pipes, - pipe_idx); -// TTU - Cursor refcyc_per_req_delivery_pre_cur0 =0.0 ; refcyc_per_req_delivery_cur0 =0.0 ;
@@ -1511,17 +1490,7 @@ static void dml20v2_rq_dlg_get_dlg_params(struct display_mode_lib *mode_lib, disp_dlg_regs->chunk_hdl_adjust_cur1 =3 ; disp_dlg_regs->dst_y_offset_cur1 =0 ; - disp_dlg_regs->xfc_reg_transfer_delay = xfc_transfer_delay; - disp_dlg_regs->xfc_reg_precharge_delay = xfc_precharge_delay; - disp_dlg_regs->xfc_reg_remote_surface_flip_latency = xfc_remote_surface_flip_latency; - disp_dlg_regs->xfc_reg_prefetch_margin =dml_ceil (xfc_prefetch_margin * refclk_freq_in_mhz, -1 ); - -// slave has to have this value also set to off -if (src->xfc_enable && !src->xfc_slave) - disp_dlg_regs->dst_y_delta_drq_limit =dml_ceil (xfc_dst_y_delta_drq_limit,1 ); -else - disp_dlg_regs->dst_y_delta_drq_limit =0x7fff ;// off + disp_dlg_regs->dst_y_delta_drq_limit =0x7fff ;// off disp_ttu_regs->refcyc_per_req_delivery_pre_l = (unsigned int ) (refcyc_per_req_delivery_pre_l *dml_pow (2 ,10 ));
drivers/gpu/drm/amd/display/dc/dml/dcn21/display_rq_dlg_calc_21.c +1 -35
@@ -936,11 +936,6 @@ static void dml_rq_dlg_get_dlg_params(double refcyc_per_req_delivery_c;unsigned int full_recout_width; -double xfc_transfer_delay; -double xfc_precharge_delay; -double xfc_remote_surface_flip_latency; -double xfc_dst_y_delta_drq_limit; -double xfc_prefetch_margin;double refcyc_per_req_delivery_pre_cur0;double refcyc_per_req_delivery_cur0;double refcyc_per_req_delivery_pre_cur1;
@@ -1412,25 +1407,6 @@ static void dml_rq_dlg_get_dlg_params(ASSERT (refcyc_per_req_delivery_c <dml_pow (2 ,13 )); } -// XFC - xfc_transfer_delay =get_xfc_transfer_delay (mode_lib, e2e_pipe_param, num_pipes, pipe_idx); - xfc_precharge_delay =get_xfc_precharge_delay ( - mode_lib, - e2e_pipe_param, - num_pipes, - pipe_idx); - xfc_remote_surface_flip_latency =get_xfc_remote_surface_flip_latency ( - mode_lib, - e2e_pipe_param, - num_pipes, - pipe_idx); - xfc_dst_y_delta_drq_limit = xfc_remote_surface_flip_latency; - xfc_prefetch_margin =get_xfc_prefetch_margin ( - mode_lib, - e2e_pipe_param, - num_pipes, - pipe_idx); -// TTU - Cursor refcyc_per_req_delivery_pre_cur0 =0.0 ; refcyc_per_req_delivery_cur0 =0.0 ;
@@ -1621,17 +1597,7 @@ static void dml_rq_dlg_get_dlg_params( disp_dlg_regs->chunk_hdl_adjust_cur1 =3 ; disp_dlg_regs->dst_y_offset_cur1 =0 ; - disp_dlg_regs->xfc_reg_transfer_delay = xfc_transfer_delay; - disp_dlg_regs->xfc_reg_precharge_delay = xfc_precharge_delay; - disp_dlg_regs->xfc_reg_remote_surface_flip_latency = xfc_remote_surface_flip_latency; - disp_dlg_regs->xfc_reg_prefetch_margin =dml_ceil ( - xfc_prefetch_margin * refclk_freq_in_mhz,1 ); - -// slave has to have this value also set to off -if (src->xfc_enable && !src->xfc_slave) - disp_dlg_regs->dst_y_delta_drq_limit =dml_ceil (xfc_dst_y_delta_drq_limit,1 ); -else - disp_dlg_regs->dst_y_delta_drq_limit =0x7fff ;// off + disp_dlg_regs->dst_y_delta_drq_limit =0x7fff ;// off disp_ttu_regs->refcyc_per_req_delivery_pre_l = (unsigned int ) (refcyc_per_req_delivery_pre_l *dml_pow (2 ,10 ));
drivers/gpu/drm/amd/display/dc/dml/display_mode_enums.h +7 -1
@@ -177,8 +177,14 @@ enum odm_combine_policy { };enum immediate_flip_requirement { - dm_immediate_flip_not_required, dm_immediate_flip_required, + dm_immediate_flip_not_required, +}; + +enum unbounded_requesting_policy { + dm_unbounded_requesting, + dm_unbounded_requesting_edp_only, + dm_unbounded_requesting_disable };#endif
drivers/gpu/drm/amd/display/dc/dml/display_mode_structs.h +11 -0
@@ -82,6 +82,7 @@ struct _vcs_dpi_soc_bounding_box_st {double pct_ideal_dram_sdp_bw_after_urgent_pixel_only;// PercentOfIdealDRAMFabricAndSDPPortBWReceivedAfterUrgLatencyPixelDataOnly double pct_ideal_dram_sdp_bw_after_urgent_pixel_and_vm;double pct_ideal_dram_sdp_bw_after_urgent_vm_only; +double pct_ideal_sdp_bw_after_urgent;double max_avg_sdp_bw_use_normal_percent;double max_avg_dram_bw_use_normal_percent;unsigned int max_request_size_bytes;
@@ -125,6 +126,7 @@ struct _vcs_dpi_ip_params_st {bool use_min_dcfclk;bool gpuvm_enable;bool hostvm_enable; +bool dsc422_native_support;unsigned int gpuvm_max_page_table_levels;unsigned int hostvm_max_page_table_levels;unsigned int hostvm_cached_page_table_levels;
@@ -143,6 +145,7 @@ struct _vcs_dpi_ip_params_st {unsigned char pte_enable;unsigned int pte_chunk_size_kbytes;unsigned int meta_chunk_size_kbytes; +unsigned int min_meta_chunk_size_bytes;unsigned int writeback_chunk_size_kbytes;unsigned int line_buffer_size_bits;unsigned int max_line_buffer_lines;
@@ -158,6 +161,7 @@ struct _vcs_dpi_ip_params_st {double writeback_max_vscl_ratio;double writeback_min_hscl_ratio;double writeback_min_vscl_ratio; +double maximum_dsc_bits_per_component;unsigned int writeback_max_hscl_taps;unsigned int writeback_max_vscl_taps;unsigned int writeback_line_buffer_luma_buffer_size;
@@ -219,11 +223,14 @@ struct _vcs_dpi_display_xfc_params_st {struct _vcs_dpi_display_pipe_source_params_st {int source_format; +double dcc_fraction_of_zs_req_luma; +double dcc_fraction_of_zs_req_chroma;unsigned char dcc;unsigned int dcc_rate;unsigned int dcc_rate_chroma;unsigned char dcc_use_global;unsigned char vm; +bool unbounded_req_mode;bool gpuvm;// gpuvm enabled bool hostvm;// hostvm enabled bool gpuvm_levels_force_en;
@@ -324,6 +331,8 @@ struct _vcs_dpi_display_pipe_dest_params_st {unsigned int vblank_end;unsigned int htotal;unsigned int vtotal; +unsigned int refresh_rate; +unsigned int vfront_porch;unsigned int vactive;unsigned int hactive;unsigned int vstartup_start;
@@ -333,6 +342,7 @@ struct _vcs_dpi_display_pipe_dest_params_st {unsigned char interlaced;double pixel_rate_mhz;unsigned char synchronized_vblank_all_planes; +unsigned char synchronize_timing_if_single_refresh_rate;unsigned char otg_inst;unsigned int odm_combine;unsigned char use_maximum_vstartup;
@@ -469,6 +479,7 @@ struct _vcs_dpi_display_dlg_regs_st {unsigned int refcyc_per_vm_req_vblank;unsigned int refcyc_per_vm_req_flip;unsigned int refcyc_per_vm_dmdata; +unsigned int dmdata_dl_delta; };struct _vcs_dpi_display_ttu_regs_st {
drivers/gpu/drm/amd/display/dc/dml/display_mode_vba.c +37 -17
103 lines not on this page · raw message
drivers/gpu/drm/amd/display/dc/dml/display_mode_vba.h +128 -99
394 lines not on this page · raw message
Signature · 6 lines
2.26.2 _______________________________________________ amd-gfx mailing list [email protected] https://lists.freedesktop.org/mailman/listinfo/amd-gfx
PATCH 15/27 drm/amd/display: DP link layer test 4.2.1.1 fix due to specs update
In reply to Rodrigo SiqueiraFrom: Wenjing Liu <[email protected]>
[why]
DP link layer CTS specs updated to change the test parameters in test 4.2.1.1.
Before it requires source to delay 400us on aux no reply. With the specs updates Errata5, it requires source to delay 3.2ms (based on LTTPR aux timeout)
This causes our test to fail after updating with the latest test equipment firmware.
[how]
the change is to allow LTTPR 3.2ms aux timeout delay by default. And only set to 400us if LTTPR is not present.
Before this piece of logic is interwined with LTTPR support. Now we will default to 3.2ms aux timeout even if LTTPR support is not enabled by driver.
--- drivers/gpu/drm/amd/display/dc/core/dc_link.c | 3 +- .../gpu/drm/amd/display/dc/core/dc_link_ddc.c | 13 ++-- .../gpu/drm/amd/display/dc/core/dc_link_dp.c | 59 +++++++++---------- .../drm/amd/display/dc/core/dc_link_hwss.c | 2 +- drivers/gpu/drm/amd/display/dc/dc.h | 2 +- drivers/gpu/drm/amd/display/dc/dc_link.h | 1 + .../gpu/drm/amd/display/dc/inc/dc_link_ddc.h | 2 +- .../gpu/drm/amd/display/dc/inc/dc_link_dp.h | 2 +- 8 files changed, 42 insertions(+), 42 deletions(-)
drivers/gpu/drm/amd/display/dc/core/dc_link.c +1 -2
@@ -691,10 +691,9 @@ static bool detect_dp(struct dc_link *link,if (sink_caps->transaction_type ==DDC_TRANSACTION_TYPE_I2C_OVER_AUX ) { sink_caps->signal =SIGNAL_TYPE_DISPLAY_PORT ; -dpcd_set_source_specific_data (link); -if (!detect_dp_sink_caps (link))return false; +dpcd_set_source_specific_data (link);if (is_mst_supported (link)) { sink_caps->signal =SIGNAL_TYPE_DISPLAY_PORT_MST ;
drivers/gpu/drm/amd/display/dc/core/dc_link_ddc.c +7 -6
@@ -648,16 +648,17 @@ bool dc_link_aux_transfer_with_retries(struct ddc_service *ddc, } -uint32_t dc_link_aux_configure_timeout (struct ddc_service *ddc, +bool dc_link_aux_try_to_configure_timeout (struct ddc_service *ddc,uint32_t timeout) { -uint32_t prev_timeout =0 ; +bool result = false;struct ddc *ddc_pin = ddc->ddc_pin; -if (ddc->ctx->dc->res_pool->engines[ddc_pin->pin_data->en]->funcs->configure_timeout) - prev_timeout = - ddc->ctx->dc->res_pool->engines[ddc_pin->pin_data->en]->funcs->configure_timeout (ddc, timeout); -return prev_timeout; +if (ddc->ctx->dc->res_pool->engines[ddc_pin->pin_data->en]->funcs->configure_timeout) { + ddc->ctx->dc->res_pool->engines[ddc_pin->pin_data->en]->funcs->configure_timeout (ddc, timeout); + result = true; + } +return result; }/*test only function*/
drivers/gpu/drm/amd/display/dc/core/dc_link_dp.c +29 -30
129 lines not on this page · raw message
drivers/gpu/drm/amd/display/dc/core/dc_link_hwss.c +1 -1
@@ -281,7 +281,7 @@ void dp_set_hw_lane_settings( {struct link_encoder *encoder = link->link_enc; -if (!link->is_lttpr_mode_transparent && !is_immediate_downstream (link, offset)) +if (link->lttpr_non_transparent_mode && !is_immediate_downstream (link, offset))return ;/* call Encoder to set lane settings */
drivers/gpu/drm/amd/display/dc/dc.h +1 -1
@@ -274,7 +274,7 @@ struct dc_config {bool edp_not_connected;bool force_enum_edp;bool forced_clocks; -bool disable_extended_timeout_support;// Used to disable extended timeout and lttpr feature as well +bool allow_lttpr_non_transparent_mode;bool multi_mon_pp_mclk_switch;bool disable_dmcu;bool enable_4to1MPC;
drivers/gpu/drm/amd/display/dc/dc_link.h +1 -0
@@ -101,6 +101,7 @@ struct dc_link {bool aux_access_disabled;bool sync_lt_in_progress;bool is_lttpr_mode_transparent; +bool lttpr_non_transparent_mode;/* caps is the same as reported_link_cap. link_traing use * reported_link_cap. Will clean up. TODO
drivers/gpu/drm/amd/display/dc/inc/dc_link_ddc.h +1 -1
@@ -105,7 +105,7 @@ int dc_link_aux_transfer_raw(struct ddc_service *ddc,bool dc_link_aux_transfer_with_retries (struct ddc_service *ddc,struct aux_payload *payload); -uint32_t dc_link_aux_configure_timeout (struct ddc_service *ddc, +bool dc_link_aux_try_to_configure_timeout (struct ddc_service *ddc,uint32_t timeout); void dal_ddc_service_write_scdc_data(
drivers/gpu/drm/amd/display/dc/inc/dc_link_dp.h +1 -1
@@ -28,7 +28,7 @@#define LINK_TRAINING_ATTEMPTS 4#define LINK_TRAINING_RETRY_DELAY 50/* ms */ -#define LINK_AUX_DEFAULT_EXTENDED_TIMEOUT_PERIOD 3200/*us*/ +#define LINK_AUX_DEFAULT_LTTPR_TIMEOUT_PERIOD 3200/*us*/ #define LINK_AUX_DEFAULT_TIMEOUT_PERIOD 552/*us*/ struct dc_link ;
Signature · 6 lines
2.26.2 _______________________________________________ amd-gfx mailing list [email protected] https://lists.freedesktop.org/mailman/listinfo/amd-gfx
PATCH 16/27 drm/amd/display: vbios data table packing
In reply to Rodrigo SiqueiraFrom: Jake Wang <[email protected]>
[WHY]
Currently we're copying the entire bios image into vbios. Loading time for FW with entire bios(54272 bytes) is 105138us. By copying only the sections of bios we're using(4436 bytes), loading time drops to 104326us which saves us 812us.
[HOW]
ROM header, master data table, and all data tables will be packed in contiguous manner. The offsets for the data tables are remapped to their newly packed location.
--- .../drm/amd/display/dc/bios/bios_parser2.c | 98 +++++++++++++++++++ .../gpu/drm/amd/display/dc/dc_bios_types.h | 4 +- 2 files changed, 101 insertions(+), 1 deletion(-)
drivers/gpu/drm/amd/display/dc/bios/bios_parser2.c +98 -0
@@ -1877,6 +1877,103 @@ static enum bp_result bios_get_board_layout_info(return BP_RESULT_OK ; } +static uint16_t bios_parser_pack_data_tables ( +struct dc_bios *dcb, +void *dst) +{ +struct bios_parser *bp =BP_FROM_DCB (dcb); +struct atom_rom_header_v2_2 *rom_header =NULL ; +struct atom_rom_header_v2_2 *packed_rom_header =NULL ; +struct atom_common_table_header *data_tbl_header =NULL ; +struct atom_master_list_of_data_tables_v2_1 *data_tbl_list =NULL ; +struct atom_master_data_table_v2_1 *packed_master_data_tbl =NULL ; +struct atom_data_revision tbl_rev = {0 }; +uint16_t *rom_header_offset =NULL ; +const uint8_t *bios = bp->base.bios; +uint8_t *bios_dst = (uint8_t *)dst; +uint16_t packed_rom_header_offset; +uint16_t packed_masterdatatable_offset; +uint16_t packed_data_tbl_offset; +uint16_t data_tbl_offset; +unsigned int i; + + rom_header_offset = +GET_IMAGE (uint16_t,OFFSET_TO_ATOM_ROM_HEADER_POINTER ); + +if (!rom_header_offset) +return 0 ; + + rom_header = GET_IMAGE(struct atom_rom_header_v2_2, *rom_header_offset); + +if (!rom_header) +return 0 ; + +get_atom_data_table_revision (&rom_header->table_header, &tbl_rev); +if (!(tbl_rev.major >=2 && tbl_rev.minor >=2 )) +return 0 ; + +get_atom_data_table_revision (&bp->master_data_tbl->table_header, &tbl_rev); +if (!(tbl_rev.major >=2 && tbl_rev.minor >=1 )) +return 0 ; + + packed_rom_header_offset = +OFFSET_TO_ATOM_ROM_HEADER_POINTER +sizeof (*rom_header_offset); + + packed_masterdatatable_offset = + packed_rom_header_offset + rom_header->table_header.structuresize; + + packed_data_tbl_offset = + packed_masterdatatable_offset + + bp->master_data_tbl->table_header.structuresize; + + packed_rom_header = + (struct atom_rom_header_v2_2 *)(bios_dst + packed_rom_header_offset); + + packed_master_data_tbl = + (struct atom_master_data_table_v2_1 *)(bios_dst + + packed_masterdatatable_offset); + +memcpy (bios_dst, bios,OFFSET_TO_ATOM_ROM_HEADER_POINTER ); + + *((uint16_t *)(bios_dst +OFFSET_TO_ATOM_ROM_HEADER_POINTER )) = + packed_rom_header_offset; + +memcpy (bios_dst + packed_rom_header_offset, rom_header, + rom_header->table_header.structuresize); + + packed_rom_header->masterdatatable_offset = packed_masterdatatable_offset; + +memcpy (&packed_master_data_tbl->table_header, + &bp->master_data_tbl->table_header, +sizeof (bp->master_data_tbl->table_header)); + + data_tbl_list = &bp->master_data_tbl->listOfdatatables; + +/* Each data table offset in data table list is 2 bytes, +* we can use that to iterate through listOfdatatables +* without knowing the name of each member. +*/ +for (i =0 ; i <sizeof (*data_tbl_list)/sizeof (uint16_t ); i++) { + data_tbl_offset = *((uint16_t *)data_tbl_list + i); + +if (data_tbl_offset) { + data_tbl_header = + (struct atom_common_table_header *)(bios + data_tbl_offset); + +memcpy (bios_dst + packed_data_tbl_offset, data_tbl_header, + data_tbl_header->structuresize); + + *((uint16_t *)&packed_master_data_tbl->listOfdatatables + i) = + packed_data_tbl_offset; + + packed_data_tbl_offset += data_tbl_header->structuresize; + }else { + *((uint16_t *)&packed_master_data_tbl->listOfdatatables + i) =0 ; + } + } +return packed_data_tbl_offset; +} +static const struct dc_vbios_funcs vbios_funcs = { .get_connectors_number = bios_parser_get_connectors_number,
@@ -1925,6 +2022,7 @@ static const struct dc_vbios_funcs vbios_funcs = { .bios_parser_destroy = firmware_parser_destroy, .get_board_layout_info = bios_get_board_layout_info, + .pack_data_tables = bios_parser_pack_data_tables, }; static bool bios_parser2_construct(
drivers/gpu/drm/amd/display/dc/dc_bios_types.h +3 -1
@@ -89,7 +89,6 @@ struct dc_vbios_funcs {bool (*is_device_id_supported)(struct dc_bios *bios,struct device_id id); -/* COMMANDS */ enum bp_result (*encoder_control)(
@@ -131,6 +130,9 @@ struct dc_vbios_funcs {enum bp_result (*get_board_layout_info)(struct dc_bios *dcb,struct board_layout_info *board_layout_info); +uint16_t (*pack_data_tables)( +struct dc_bios *dcb, +void *dst); };struct bios_registers {
Signature · 6 lines
2.26.2 _______________________________________________ amd-gfx mailing list [email protected] https://lists.freedesktop.org/mailman/listinfo/amd-gfx
PATCH 17/27 drm/amd/display: Defer cursor lock until after VUPDATE
In reply to Rodrigo SiqueiraFrom: Nicholas Kazlauskas <[email protected]>
[Why]
We dropped the delay after changed the cursor functions locking the entire pipe to locking just the CURSOR registers to fix page flip stuttering - this introduced cursor stuttering instead, and an underflow issue.
The cursor update can be delayed indefinitely if the cursor update repeatedly happens right around VUPDATE.
The underflow issue can happen if we do a viewport update on a pipe on the same frame where a cursor update happens around VUPDATE - the old cursor registers are retained which can be in an invalid position.
This can cause a pipe hang and indefinite underflow.
[How]
The complex, ideal solution to the problem would be a software triple buffering mechanism from the DM layer to program only one cursor update per frame just before VUPDATE.
The simple workaround until we have that infrastructure in place is this change - bring back the delay until VUPDATE before locking, but with some corrections to the calculations.
This didn't work for all timings before because the calculation for VUPDATE was wrong - it was using the offset from VSTARTUP instead and didn't correctly handle the case where VUPDATE could be in the back porch.
Add a new hardware sequencer function to use the existing helper to calculate the real VUPDATE start and VUPDATE end - VUPDATE can last multiple lines after all.
Change the udelay to incorporate the width of VUPDATE as well.
--- .../amd/display/dc/dcn10/dcn10_hw_sequencer.c | 69 ++++++++++++++++++- .../amd/display/dc/dcn10/dcn10_hw_sequencer.h | 5 ++ .../gpu/drm/amd/display/dc/dcn10/dcn10_init.c | 1 + .../gpu/drm/amd/display/dc/dcn20/dcn20_init.c | 1 + .../gpu/drm/amd/display/dc/dcn21/dcn21_init.c | 1 + .../gpu/drm/amd/display/dc/inc/hw_sequencer.h | 5 ++ 6 files changed, 81 insertions(+), 1 deletion(-)
drivers/gpu/drm/amd/display/dc/dcn10/dcn10_hw_sequencer.c +68 -1
@@ -1682,12 +1682,79 @@ void dcn10_pipe_control_lock( hws->funcs.verify_allow_pstate_change_high (dc); } +/** +* delay_cursor_until_vupdate() - Delay cursor update if too close to VUPDATE. +* +* Software keepout workaround to prevent cursor update locking from stalling +* out cursor updates indefinitely or from old values from being retained in +* the case where the viewport changes in the same frame as the cursor. +* +* The idea is to calculate the remaining time from VPOS to VUPDATE. If it's +* too close to VUPDATE, then stall out until VUPDATE finishes. +* +* TODO: Optimize cursor programming to be once per frame before VUPDATE +* to avoid the need for this workaround. +*/ +static void delay_cursor_until_vupdate (struct dc *dc,struct pipe_ctx *pipe_ctx) +{ +struct dc_stream_state *stream = pipe_ctx->stream; +struct crtc_position position; +uint32_t vupdate_start, vupdate_end; +unsigned int lines_to_vupdate, us_to_vupdate, vpos; +unsigned int us_per_line, us_vupdate; + +if (!dc->hwss.calc_vupdate_position || !dc->hwss.get_position) +return ; + +if (!pipe_ctx->stream_res.stream_enc || !pipe_ctx->stream_res.tg) +return ; + + dc->hwss.calc_vupdate_position (dc, pipe_ctx, &vupdate_start, + &vupdate_end); + + dc->hwss.get_position (&pipe_ctx,1 , &position); + vpos = position.vertical_count; + +/* Avoid wraparound calculation issues */ + vupdate_start += stream->timing.v_total; + vupdate_end += stream->timing.v_total; + vpos += stream->timing.v_total; + +if (vpos <= vupdate_start) { +/* VPOS is in VACTIVE or back porch. */ + lines_to_vupdate = vupdate_start - vpos; + }else if (vpos > vupdate_end) { +/* VPOS is in the front porch. */ +return ; + }else { +/* VPOS is in VUPDATE. */ + lines_to_vupdate =0 ; + } + +/* Calculate time until VUPDATE in microseconds. */ + us_per_line = + stream->timing.h_total *10000u / stream->timing.pix_clk_100hz; + us_to_vupdate = lines_to_vupdate * us_per_line; + +/* 70 us is a conservative estimate of cursor update time*/ +if (us_to_vupdate >70 ) +return ; + +/* Stall out until the cursor update completes. */ + us_vupdate = (vupdate_end - vupdate_start +1 ) * us_per_line; +udelay (us_to_vupdate + us_vupdate); +} +void dcn10_cursor_lock (struct dc *dc,struct pipe_ctx *pipe,bool lock) {/* cursor lock is per MPCC tree, so only need to lock one pipe per stream */ if (!pipe || pipe->top_pipe)return ; +/* Prevent cursor lock from stalling out cursor updates. */ +if (lock) +delay_cursor_until_vupdate (dc, pipe); + dc->res_pool->mpc->funcs->cursor_lock (dc->res_pool->mpc, pipe->stream_res.opp->inst, lock); }
@@ -3300,7 +3367,7 @@ int dcn10_get_vupdate_offset_from_vsync(struct pipe_ctx *pipe_ctx)return vertical_line_start; } -static void dcn10_calc_vupdate_position( +void dcn10_calc_vupdate_position( struct dc *dc, struct pipe_ctx *pipe_ctx, uint32_t *start_line,
drivers/gpu/drm/amd/display/dc/dcn10/dcn10_hw_sequencer.h +5 -0
@@ -34,6 +34,11 @@ struct dc;void dcn10_hw_sequencer_construct (struct dc *dc);int dcn10_get_vupdate_offset_from_vsync (struct pipe_ctx *pipe_ctx); +void dcn10_calc_vupdate_position ( +struct dc *dc, +struct pipe_ctx *pipe_ctx, +uint32_t *start_line, +uint32_t *end_line);void dcn10_setup_vupdate_interrupt (struct dc *dc,struct pipe_ctx *pipe_ctx); enum dc_status dcn10_enable_stream_timing( struct pipe_ctx *pipe_ctx,
drivers/gpu/drm/amd/display/dc/dcn10/dcn10_init.c +1 -0
@@ -72,6 +72,7 @@ static const struct hw_sequencer_funcs dcn10_funcs = { .set_clock = dcn10_set_clock, .get_clock = dcn10_get_clock, .get_vupdate_offset_from_vsync = dcn10_get_vupdate_offset_from_vsync, + .calc_vupdate_position = dcn10_calc_vupdate_position, .set_backlight_level = dce110_set_backlight_level, .set_abm_immediate_disable = dce110_set_abm_immediate_disable, .set_pipe = dce110_set_pipe,
drivers/gpu/drm/amd/display/dc/dcn20/dcn20_init.c +1 -0
@@ -83,6 +83,7 @@ static const struct hw_sequencer_funcs dcn20_funcs = { .init_vm_ctx = dcn20_init_vm_ctx, .set_flip_control_gsl = dcn20_set_flip_control_gsl, .get_vupdate_offset_from_vsync = dcn10_get_vupdate_offset_from_vsync, + .calc_vupdate_position = dcn10_calc_vupdate_position, .set_backlight_level = dce110_set_backlight_level, .set_abm_immediate_disable = dce110_set_abm_immediate_disable, .set_pipe = dce110_set_pipe,
drivers/gpu/drm/amd/display/dc/dcn21/dcn21_init.c +1 -0
@@ -86,6 +86,7 @@ static const struct hw_sequencer_funcs dcn21_funcs = { .optimize_pwr_state = dcn21_optimize_pwr_state, .exit_optimized_pwr_state = dcn21_exit_optimized_pwr_state, .get_vupdate_offset_from_vsync = dcn10_get_vupdate_offset_from_vsync, + .calc_vupdate_position = dcn10_calc_vupdate_position, .power_down = dce110_power_down, .set_backlight_level = dcn21_set_backlight_level, .set_abm_immediate_disable = dcn21_set_abm_immediate_disable,
drivers/gpu/drm/amd/display/dc/inc/hw_sequencer.h +5 -0
@@ -96,6 +96,11 @@ struct hw_sequencer_funcs {void (*get_position)(struct pipe_ctx **pipe_ctx,int num_pipes,struct crtc_position *position);int (*get_vupdate_offset_from_vsync)(struct pipe_ctx *pipe_ctx); +void (*calc_vupdate_position)( +struct dc *dc, +struct pipe_ctx *pipe_ctx, +uint32_t *start_line, +uint32_t *end_line);void (*enable_per_frame_crtc_position_reset)(struct dc *dc,int group_size,struct pipe_ctx *grouped_pipes[]); void (*enable_timing_synchronization)(struct dc *dc,
Signature · 6 lines
2.26.2 _______________________________________________ amd-gfx mailing list [email protected] https://lists.freedesktop.org/mailman/listinfo/amd-gfx
PATCH 18/27 drm/amd/display: Avoid pipe split when plane is too small
In reply to Rodrigo SiqueiraFrom: Nicholas Kazlauskas <[email protected]>
[Why]
The minimum plane size we can support in DML is 16x16. If we try to pass a 16x16 plane with dynamic pipe split then validation will fail since it tries to split it into two pipes, each 8x8.
Some userspace doesn't check that the commit fails and because the commit fails the old state is retained, resulting in corruption.
[How]
Add a workaround to avoid pipe split if any plane is 16x16 or smaller.
--- .../gpu/drm/amd/display/dc/calcs/dcn_calcs.c | 21 ++++++++++++++++++- .../drm/amd/display/dc/dcn20/dcn20_resource.c | 14 ++++++++++++- 2 files changed, 33 insertions(+), 2 deletions(-)
drivers/gpu/drm/amd/display/dc/calcs/dcn_calcs.c +20 -1
@@ -690,6 +690,26 @@ static void hack_bounding_box(struct dcn_bw_internal_vars *v,struct dc_debug_options *dbg, struct dc_state *context) { + int i; + +for (i =0 ; i <MAX_PIPES ; i++) { +struct pipe_ctx *pipe = &context->res_ctx.pipe_ctx[i]; + +/** +* Workaround for avoiding pipe-split in cases where we'd split +* planes that are too small, resulting in splits that aren't +* valid for the scaler. +*/ +if (pipe->plane_state && + (pipe->plane_state->dst_rect.width <=16 || + pipe->plane_state->dst_rect.height <=16 || + pipe->plane_state->src_rect.width <=16 || + pipe->plane_state->src_rect.height <=16 )) { +hack_disable_optional_pipe_split (v); +return ; + } + } +if (dbg->pipe_split_policy ==MPC_SPLIT_AVOID )hack_disable_optional_pipe_split (v);
@@ -702,7 +722,6 @@ static void hack_bounding_box(struct dcn_bw_internal_vars *v,hack_force_pipe_split (v, context->streams[0 ]->timing.pix_clk_100hz); } -unsigned int get_highest_allowed_voltage_level (uint32_t hw_internal_rev,uint32_t pci_revision_id) {/* for low power RV2 variants, the highest voltage level we want is 0 */
drivers/gpu/drm/amd/display/dc/dcn20/dcn20_resource.c +13 -1
@@ -2606,10 +2606,22 @@ int dcn20_validate_apply_pipe_split_flags( }else if (dc->debug.force_single_disp_pipe_split) force_split = true; -/* TODO: fix dc bugs and remove this split threshold thing */ for (i =0 ; i < dc->res_pool->pipe_count; i++) {struct pipe_ctx *pipe = &context->res_ctx.pipe_ctx[i]; +/** +* Workaround for avoiding pipe-split in cases where we'd split +* planes that are too small, resulting in splits that aren't +* valid for the scaler. +*/ +if (pipe->plane_state && + (pipe->plane_state->dst_rect.width <=16 || + pipe->plane_state->dst_rect.height <=16 || + pipe->plane_state->src_rect.width <=16 || + pipe->plane_state->src_rect.height <=16 )) + avoid_split = true; + +/* TODO: fix dc bugs and remove this split threshold thing */ if (pipe->stream && !pipe->prev_odm_pipe && (!pipe->top_pipe || pipe->top_pipe->plane_state != pipe->plane_state)) ++plane_count;
Signature · 6 lines
2.26.2 _______________________________________________ amd-gfx mailing list [email protected] https://lists.freedesktop.org/mailman/listinfo/amd-gfx
PATCH 19/27 drm/amd/display: correct rn NUM_VMID
In reply to Rodrigo SiqueiraFrom: Dmytro Laktyushkin <[email protected]>
Save the correct num vmid during resource creation and fix RN gpuvm level from 1 to 16 vmid entries.
--- drivers/gpu/drm/amd/display/dc/dcn20/dcn20_hubbub.h | 1 + drivers/gpu/drm/amd/display/dc/dcn21/dcn21_hubbub.c | 7 +------ drivers/gpu/drm/amd/display/dc/dcn21/dcn21_resource.c | 3 ++- drivers/gpu/drm/amd/display/modules/vmid/vmid.c | 7 +++++-- 4 files changed, 9 insertions(+), 9 deletions(-)
drivers/gpu/drm/amd/display/dc/dcn20/dcn20_hubbub.h +1 -0
@@ -80,6 +80,7 @@ struct dcn20_hubbub {const struct dcn_hubbub_mask *masks;unsigned int debug_test_index_pstate;struct dcn_watermark_set watermarks; +int num_vmid;struct dcn20_vmid vmid[16 ];unsigned int detile_buf_size; };
drivers/gpu/drm/amd/display/dc/dcn21/dcn21_hubbub.c +1 -6
@@ -49,11 +49,6 @@#define FN (reg_name, field_name) \ hubbub1->shifts->field_name, hubbub1->masks->field_name -#ifdef NUM_VMID -#undef NUM_VMID -#endif -#define NUM_VMID 16 - static uint32_t convert_and_clamp( uint32_t wm_ns, uint32_t refclk_mhz,
@@ -138,7 +133,7 @@ int hubbub21_init_dchub(struct hubbub *hubbub,dcn21_dchvm_init (hubbub); -return NUM_VMID ; +return hubbub1->num_vmid; } bool hubbub21_program_urgent_watermarks(
drivers/gpu/drm/amd/display/dc/dcn21/dcn21_resource.c +2 -1
@@ -805,7 +805,7 @@ static const struct resource_caps res_cap_rn = { .num_pll = 5, // maybe 3 because the last two used for USB-c .num_dwb = 1, .num_ddc = 5, - .num_vmid = 1, + .num_vmid = 16, .num_dsc = 3, };
@@ -1295,6 +1295,7 @@ static struct hubbub *dcn21_hubbub_create(struct dc_context *ctx) vmid->shifts = &vmid_shifts; vmid->masks = &vmid_masks; } + hubbub->num_vmid = res_cap_rn.num_vmid;return &hubbub->base; }
drivers/gpu/drm/amd/display/modules/vmid/vmid.c +5 -2
@@ -112,9 +112,12 @@ uint8_t mod_vmid_get_for_ptb(struct mod_vmid *mod_vmid, uint64_t ptb)evict_vmids (core_vmid); vmid =get_next_available_vmid (core_vmid); -add_ptb_to_table (core_vmid, vmid, ptb); +if (vmid !=-1 ) { +add_ptb_to_table (core_vmid, vmid, ptb); -dc_setup_vm_context (core_vmid->dc, &va_config, vmid); +dc_setup_vm_context (core_vmid->dc, &va_config, vmid); + }else +ASSERT (0 ); }return vmid;
Signature · 6 lines
2.26.2 _______________________________________________ amd-gfx mailing list [email protected] https://lists.freedesktop.org/mailman/listinfo/amd-gfx
PATCH 20/27 drm/amd/display: Fix incorrectly pruned modes with deep color
In reply to Rodrigo SiqueiraFrom: Stylon Wang <[email protected]>
[Why]
When "max bpc" is set to enable deep color, some modes are removed from the list if they fail validation on max bpc. These modes should be kept if they validates fine with lower bpc.
[How]
- Retry with lower bpc in mode validation.
- Same in atomic commit to apply working bpc, not necessarily max bpc.
--- .../gpu/drm/amd/display/amdgpu_dm/amdgpu_dm.c | 102 +++++++++++------- 1 file changed, 64 insertions(+), 38 deletions(-)
drivers/gpu/drm/amd/display/amdgpu_dm/amdgpu_dm.c +64 -38
@@ -3895,8 +3895,7 @@ static void update_stream_scaling_settings(const struct drm_display_mode *mode,static enum dc_color_depth convert_color_depth_from_display_info (const struct drm_connector *connector, -const struct drm_connector_state *state, -bool is_y420) +bool is_y420,int requested_bpc) {uint8_t bpc;
@@ -3916,10 +3915,7 @@ convert_color_depth_from_display_info(const struct drm_connector *connector, bpc = bpc ? bpc :8 ; } -if (!state) - state = connector->state; - -if (state) { +if (requested_bpc >0 ) {/* * Cap display bpc based on the user requested value. *
@@ -3928,7 +3924,7 @@ convert_color_depth_from_display_info(const struct drm_connector *connector,* or if this was called outside of atomic check, so it * can't be used directly. */ - bpc =min (bpc, state->max_requested_bpc); + bpc =min_t (u8, bpc, requested_bpc);/* Round down to the nearest even number. */ bpc = bpc - (bpc &1 );
@@ -4050,7 +4046,8 @@ static void fill_stream_properties_from_drm_display_mode(const struct drm_display_mode *mode_in, const struct drm_connector *connector, const struct drm_connector_state *connector_state, - const struct dc_stream_state *old_stream) + const struct dc_stream_state *old_stream, + int requested_bpc) { struct dc_crtc_timing *timing_out = &stream->timing;const struct drm_display_info *info = &connector->display_info;
@@ -4080,8 +4077,9 @@ static void fill_stream_properties_from_drm_display_mode( timing_out->timing_3d_format =TIMING_3D_FORMAT_NONE ; timing_out->display_color_depth =convert_color_depth_from_display_info ( - connector, connector_state, - (timing_out->pixel_encoding ==PIXEL_ENCODING_YCBCR420 )); + connector, + (timing_out->pixel_encoding ==PIXEL_ENCODING_YCBCR420 ), + requested_bpc); timing_out->scan_type =SCANNING_TYPE_NODATA ; timing_out->hdmi_vic =0 ;
@@ -4287,7 +4285,8 @@ static struct dc_stream_state * create_stream_for_sink(struct amdgpu_dm_connector *aconnector, const struct drm_display_mode *drm_mode, const struct dm_connector_state *dm_state, - const struct dc_stream_state *old_stream) + const struct dc_stream_state *old_stream, + int requested_bpc) { struct drm_display_mode *preferred_mode = NULL;struct drm_connector *drm_connector;
@@ -4372,10 +4371,10 @@ create_stream_for_sink(struct amdgpu_dm_connector *aconnector,*/ if (!scale || mode_refresh != preferred_refresh)fill_stream_properties_from_drm_display_mode (stream, - &mode, &aconnector->base, con_state,NULL ); + &mode, &aconnector->base, con_state,NULL , requested_bpc);else fill_stream_properties_from_drm_display_mode (stream, - &mode, &aconnector->base, con_state, old_stream); + &mode, &aconnector->base, con_state, old_stream, requested_bpc); stream->timing.flags.DSC =0 ;
@@ -4907,16 +4906,54 @@ static void handle_edid_mgmt(struct amdgpu_dm_connector *aconnector)create_eml_sink (aconnector); } +static struct dc_stream_state * +create_validate_stream_for_sink (struct amdgpu_dm_connector *aconnector, +const struct drm_display_mode *drm_mode, +const struct dm_connector_state *dm_state, +const struct dc_stream_state *old_stream) +{ +struct drm_connector *connector = &aconnector->base; +struct amdgpu_device *adev = connector->dev->dev_private; +struct dc_stream_state *stream; +int requested_bpc = connector->state ? connector->state->max_requested_bpc :8 ; +enum dc_status dc_result =DC_OK ; + +do { + stream =create_stream_for_sink (aconnector, drm_mode, + dm_state, old_stream, + requested_bpc); +if (stream ==NULL ) { +DRM_ERROR ("Failed to create stream for sink!\n" ); +break ; + } + + dc_result =dc_validate_stream (adev->dm.dc, stream); + +if (dc_result !=DC_OK ) { +DRM_DEBUG_KMS ("Mode %dx%d (clk %d) failed DC validation with error %d\n" , + drm_mode->hdisplay, + drm_mode->vdisplay, + drm_mode->clock, + dc_result); + +dc_stream_release (stream); + stream =NULL ; + requested_bpc -=2 ;/* lower bpc to retry validation */ + } + + }while (stream ==NULL && requested_bpc >=6 ); + +return stream; +} +enum drm_mode_status amdgpu_dm_connector_mode_valid (struct drm_connector *connector,struct drm_display_mode *mode) {int result =MODE_ERROR ;struct dc_sink *dc_sink; -struct amdgpu_device *adev = connector->dev->dev_private;/* TODO: Unhardcode stream count */ struct dc_stream_state *stream;struct amdgpu_dm_connector *aconnector =to_amdgpu_dm_connector (connector); -enum dc_status dc_result =DC_OK ;if ((mode->flags &DRM_MODE_FLAG_INTERLACE ) || (mode->flags &DRM_MODE_FLAG_DBLSCAN ))
@@ -4937,24 +4974,11 @@ enum drm_mode_status amdgpu_dm_connector_mode_valid(struct drm_connector *connec goto fail; } - stream =create_stream_for_sink (aconnector, mode,NULL ,NULL ); -if (stream ==NULL ) { -DRM_ERROR ("Failed to create stream for sink!\n" ); - goto fail; - } - - dc_result =dc_validate_stream (adev->dm.dc, stream); - -if (dc_result ==DC_OK ) + stream =create_validate_stream_for_sink (aconnector, mode,NULL ,NULL ); +if (stream) { +dc_stream_release (stream); result =MODE_OK ; -else -DRM_DEBUG_KMS ("Mode %dx%d (clk %d) failed DC validation with error %d\n" , - mode->hdisplay, - mode->vdisplay, - mode->clock, - dc_result); - -dc_stream_release (stream); + } fail:/* TODO: error handling*/
@@ -5277,10 +5301,12 @@ static int dm_encoder_helper_atomic_check(struct drm_encoder *encoder,return 0 ;if (!state->duplicated) { +int max_bpc = conn_state->max_requested_bpc; is_y420 =drm_mode_is_420_also (&connector->display_info, adjusted_mode) && aconnector->force_yuv420_output; - color_depth =convert_color_depth_from_display_info (connector, conn_state, - is_y420); + color_depth =convert_color_depth_from_display_info (connector, + is_y420, + max_bpc); bpp =convert_dc_color_depth_into_bpc (color_depth) *3 ; clock = adjusted_mode->clock; dm_new_connector_state->pbn =drm_dp_calc_pbn_mode (clock, bpp, false);
@@ -7711,10 +7737,10 @@ static int dm_update_crtc_state(struct amdgpu_display_manager *dm,if (!drm_atomic_crtc_needs_modeset (new_crtc_state)) goto skip_modeset; - new_stream =create_stream_for_sink (aconnector, - &new_crtc_state->mode, - dm_new_conn_state, - dm_old_crtc_state->stream); + new_stream =create_validate_stream_for_sink (aconnector, + &new_crtc_state->mode, + dm_new_conn_state, + dm_old_crtc_state->stream);/* * we can have no stream on ACTION_SET if a display
Signature · 6 lines
2.26.2 _______________________________________________ amd-gfx mailing list [email protected] https://lists.freedesktop.org/mailman/listinfo/amd-gfx
PATCH 21/27 drm/amd/display: Add DMUB firmware version helpers in DMUB service
In reply to Rodrigo SiqueiraFrom: Nicholas Kazlauskas <[email protected]>
[Why]
In order to switch over the inbox from region4 to cw4 we need to know if the firmware is capable of properly invalidating the cache before reading the commands.
Easiest way is to just check the firmware version, but we don't have the helper macros or a way for the dmub_srv to know what version it is.
[How]
Add a new fw_version field to the creation parameters that driver can optional pass in. Assumes a version of 0x00000000 is invalid.
--- drivers/gpu/drm/amd/display/dmub/dmub_srv.h | 11 +++++++++++ drivers/gpu/drm/amd/display/dmub/src/dmub_srv.c | 1 + 2 files changed, 12 insertions(+)
drivers/gpu/drm/amd/display/dmub/dmub_srv.h +11 -0
@@ -280,6 +280,7 @@ struct dmub_srv_hw_funcs {* @hw_funcs: optional overrides for hw funcs * @user_ctx: context data for callback funcs * @asic: driver supplied asic +* @fw_version: the current firmware version, if any * @is_virtual: false for hw support only */ struct dmub_srv_create_params {
@@ -287,6 +288,7 @@ struct dmub_srv_create_params {struct dmub_srv_hw_funcs *hw_funcs;void *user_ctx;enum dmub_asic asic; +uint32_t fw_version;bool is_virtual; };
@@ -310,12 +312,14 @@ struct dmub_srv_hw_params {* struct dmub_srv - software state for dmcub * @asic: dmub asic identifier * @user_ctx: user provided context for the dmub_srv +* @fw_version: the current firmware version, if any * @is_virtual: false if hardware support only * @fw_state: dmub firmware state pointer */ struct dmub_srv {enum dmub_asic asic;void *user_ctx; +uint32_t fw_version;bool is_virtual;struct dmub_fb scratch_mem_fb;volatile const struct dmub_fw_state *fw_state;
@@ -335,6 +339,13 @@ struct dmub_srv {uint32_t psp_version; }; +/** +* DMUB firmware version helper macro - useful for checking if the version +* of a firmware to know if feature or functionality is supported or present. +*/ +#define DMUB_FW_VERSION (major, minor, revision) \ + ((((major) & 0xFF) << 24) | (((minor) & 0xFF) << 16) | ((revision) & 0xFFFF)) +/** * dmub_srv_create() - creates the DMUB service. * @dmub: the dmub service
drivers/gpu/drm/amd/display/dmub/src/dmub_srv.c +1 -0
@@ -172,6 +172,7 @@ enum dmub_status dmub_srv_create(struct dmub_srv *dmub, dmub->funcs = params->funcs; dmub->user_ctx = params->user_ctx; dmub->asic = params->asic; + dmub->fw_version = params->fw_version; dmub->is_virtual = params->is_virtual;/* Setup asic dependent hardware funcs. */
Signature · 6 lines
2.26.2 _______________________________________________ amd-gfx mailing list [email protected] https://lists.freedesktop.org/mailman/listinfo/amd-gfx
PATCH 22/27 drm/amd/display: Support CW4 for DMUB ringbuffer inbox
In reply to Rodrigo SiqueiraFrom: Nicholas Kazlauskas <[email protected]>
[Why]
Region 4 is non cacheable and slower than using cache window 4.
[How]
Check the firmware version to determine how we should program the base address and memory windows.
--- .../gpu/drm/amd/display/dmub/src/dmub_dcn20.c | 28 ++++++++++++++----- .../gpu/drm/amd/display/dmub/src/dmub_srv.c | 3 +- 2 files changed, 23 insertions(+), 8 deletions(-)
drivers/gpu/drm/amd/display/dmub/src/dmub_dcn20.c +21 -7
@@ -215,11 +215,22 @@ void dmub_dcn20_setup_windows(struct dmub_srv *dmub,/* TODO: Move this to CW4. */ dmub_dcn20_translate_addr (&cw4->offset, fb_base, fb_offset, &offset); -REG_WRITE (DMCUB_REGION4_OFFSET , offset.u.low_part); -REG_WRITE (DMCUB_REGION4_OFFSET_HIGH , offset.u.high_part); -REG_SET_2 (DMCUB_REGION4_TOP_ADDRESS ,0 ,DMCUB_REGION4_TOP_ADDRESS , - cw4->region.top - cw4->region.base -1 ,DMCUB_REGION4_ENABLE , -1 ); +/* New firmware can support CW4. */ +if (dmub->fw_version >DMUB_FW_VERSION (1 ,0 ,10 )) { +REG_WRITE (DMCUB_REGION3_CW4_OFFSET , offset.u.low_part); +REG_WRITE (DMCUB_REGION3_CW4_OFFSET_HIGH , offset.u.high_part); +REG_WRITE (DMCUB_REGION3_CW4_BASE_ADDRESS , cw4->region.base); +REG_SET_2 (DMCUB_REGION3_CW4_TOP_ADDRESS ,0 , +DMCUB_REGION3_CW4_TOP_ADDRESS , cw4->region.top, +DMCUB_REGION3_CW4_ENABLE ,1 ); + }else { +REG_WRITE (DMCUB_REGION4_OFFSET , offset.u.low_part); +REG_WRITE (DMCUB_REGION4_OFFSET_HIGH , offset.u.high_part); +REG_SET_2 (DMCUB_REGION4_TOP_ADDRESS ,0 , +DMCUB_REGION4_TOP_ADDRESS , + cw4->region.top - cw4->region.base -1 , +DMCUB_REGION4_ENABLE ,1 ); + }dmub_dcn20_translate_addr (&cw5->offset, fb_base, fb_offset, &offset);
@@ -243,9 +254,12 @@ void dmub_dcn20_setup_windows(struct dmub_srv *dmub,void dmub_dcn20_setup_mailbox (struct dmub_srv *dmub,const struct dmub_region *inbox1) { -/* TODO: Use CW4 instead of region 4. */ +/* New firmware can support CW4 for the inbox. */ +if (dmub->fw_version >DMUB_FW_VERSION (1 ,0 ,10 )) +REG_WRITE (DMCUB_INBOX1_BASE_ADDRESS , inbox1->base); +else +REG_WRITE (DMCUB_INBOX1_BASE_ADDRESS ,0x80000000 ); -REG_WRITE (DMCUB_INBOX1_BASE_ADDRESS ,0x80000000 );REG_WRITE (DMCUB_INBOX1_SIZE , inbox1->top - inbox1->base); }
drivers/gpu/drm/amd/display/dmub/src/dmub_srv.c +2 -1
@@ -62,6 +62,7 @@#define DMUB_CW0_BASE (0x60000000)#define DMUB_CW1_BASE (0x61000000)#define DMUB_CW3_BASE (0x63000000) +#define DMUB_CW4_BASE (0x64000000)#define DMUB_CW5_BASE (0x65000000)#define DMUB_CW6_BASE (0x66000000)
@@ -403,7 +404,7 @@ enum dmub_status dmub_srv_hw_init(struct dmub_srv *dmub, cw3.region.top = cw3.region.base + bios_fb->size; cw4.offset.quad_part = mail_fb->gpu_addr; - cw4.region.base = cw3.region.top +1 ; + cw4.region.base =DMUB_CW4_BASE ; cw4.region.top = cw4.region.base + mail_fb->size; inbox1.base = cw4.region.base;
Signature · 6 lines
2.26.2 _______________________________________________ amd-gfx mailing list [email protected] https://lists.freedesktop.org/mailman/listinfo/amd-gfx
PATCH 23/27 drm/amd/display: fix dml log2 function
In reply to Rodrigo SiqueiraFrom: Dmytro Laktyushkin <[email protected]>
This change removes internal rounding in dml_log2 function.
Dml_log2 is expected to return a float output. In case an int is needed dml will floor the output on it's own.
--- drivers/gpu/drm/amd/display/dc/dml/dml_inline_defs.h | 4 ++-- 1 file changed, 2 insertions(+), 2 deletions(-)
drivers/gpu/drm/amd/display/dc/dml/dml_inline_defs.h +2 -2
@@ -86,9 +86,9 @@ static inline double dml_round(double a)return floor; } -static inline int dml_log2 (double x) +static inline double dml_log2 (double x) { -return dml_round ((double )dcn_bw_log (x,2 )); +return (double )dcn_bw_log (x,2 ); }static inline double dml_pow (double a,int exp)
Signature · 6 lines
2.26.2 _______________________________________________ amd-gfx mailing list [email protected] https://lists.freedesktop.org/mailman/listinfo/amd-gfx
PATCH 24/27 drm/amd/display: fix dml immediate flip input
In reply to Rodrigo SiqueiraFrom: Dmytro Laktyushkin <[email protected]>
Set the correct value to immediate flip required field.
--- drivers/gpu/drm/amd/display/dc/dml/display_mode_enums.h | 2 +- drivers/gpu/drm/amd/display/dc/dml/display_mode_vba.c | 6 +++++- 2 files changed, 6 insertions(+), 2 deletions(-)
drivers/gpu/drm/amd/display/dc/dml/display_mode_enums.h +1 -1
@@ -177,8 +177,8 @@ enum odm_combine_policy { };enum immediate_flip_requirement { - dm_immediate_flip_required, dm_immediate_flip_not_required, + dm_immediate_flip_required, };enum unbounded_requesting_policy {
drivers/gpu/drm/amd/display/dc/dml/display_mode_vba.c +5 -1
@@ -385,6 +385,8 @@ static void fetch_pipe_params(struct display_mode_lib *mode_lib) visited[k] = false; mode_lib->vba.NumberOfActivePlanes =0 ; + mode_lib->vba.ImmediateFlipSupport = false; + mode_lib->vba.ImmediateFlipRequirement = dm_immediate_flip_not_required;for (j =0 ; j < mode_lib->vba.cache_num_pipes; ++j) {display_pipe_source_params_st *src = &pipes[j].pipe.src;display_pipe_dest_params_st *dst = &pipes[j].pipe.dest;
@@ -635,8 +637,10 @@ static void fetch_pipe_params(struct display_mode_lib *mode_lib) } } -if (pipes[k].pipe.src.immediate_flip) +if (pipes[k].pipe.src.immediate_flip) { mode_lib->vba.ImmediateFlipSupport = true; + mode_lib->vba.ImmediateFlipRequirement = dm_immediate_flip_required; + } mode_lib->vba.NumberOfActivePlanes++; }
Signature · 6 lines
2.26.2 _______________________________________________ amd-gfx mailing list [email protected] https://lists.freedesktop.org/mailman/listinfo/amd-gfx
PATCH 25/27 drm/amd/display: Remove nv12 work around
In reply to Rodrigo SiqueiraFrom: Yongqiang Sun <[email protected]>
[Why]
dal side nv12 wa has a lot of side effects. KMD side wa is used, so this should be remove.
[How]
Removed wa from dal side.
--- .../drm/amd/display/dc/core/dc_vm_helper.c | 3 - drivers/gpu/drm/amd/display/dc/dc.h | 1 - .../drm/amd/display/dc/dcn20/dcn20_hwseq.c | 3 - .../gpu/drm/amd/display/dc/dcn21/dcn21_hubp.c | 121 +----------------- .../drm/amd/display/dc/dcn21/dcn21_resource.c | 1 - drivers/gpu/drm/amd/display/dc/inc/hw/hubp.h | 3 - 6 files changed, 2 insertions(+), 130 deletions(-)
drivers/gpu/drm/amd/display/dc/core/dc_vm_helper.c +0 -3
@@ -47,9 +47,6 @@ int dc_setup_system_context(struct dc *dc, struct dc_phy_addr_space_config *pa_c*/ memcpy (&dc->vm_pa_config, pa_config,sizeof (struct dc_phy_addr_space_config )); dc->vm_pa_config.valid = true; - -if (pa_config->is_hvm_enabled ==0 ) - dc->debug.nv12_iflip_vm_wa = false; }return num_vmids;
drivers/gpu/drm/amd/display/dc/dc.h +0 -1
@@ -471,7 +471,6 @@ struct dc_debug_options {bool cm_in_bypass;int force_clock_mode;/*every mode change.*/ -bool nv12_iflip_vm_wa;bool disable_dram_clock_change_vactive_support;bool validate_dml_output;bool enable_dmcub_surface_flip;
drivers/gpu/drm/amd/display/dc/dcn20/dcn20_hwseq.c +0 -3
@@ -1435,9 +1435,6 @@ static void dcn20_update_dchubp_dpp( hubp->power_gated = false; } -if (hubp->funcs->apply_PLAT_54186_wa && viewport_changed) - hubp->funcs->apply_PLAT_54186_wa (hubp, &plane_state->address); -if (pipe_ctx->update_flags.bits.enable || plane_state->update_flags.bits.addr_update) hws->funcs.update_plane_addr (dc, pipe_ctx);
drivers/gpu/drm/amd/display/dc/dcn21/dcn21_hubp.c +2 -119
145 lines not on this page · raw message
drivers/gpu/drm/amd/display/dc/dcn21/dcn21_resource.c +0 -1
@@ -878,7 +878,6 @@ static const struct dc_debug_options debug_defaults_drv = { .scl_reset_length10 = true, .sanity_checks = true, .disable_48mhz_pwrdwn = false, - .nv12_iflip_vm_wa = true, .usbc_combo_phy_reset_wa = true };
drivers/gpu/drm/amd/display/dc/inc/hw/hubp.h +0 -3
@@ -104,9 +104,6 @@ struct hubp_funcs {const struct rect *viewport, const struct rect *viewport_c); -void (*apply_PLAT_54186_wa)(struct hubp *hubp, -const struct dc_plane_address *address); - bool (*hubp_program_surface_flip_and_addr)( struct hubp *hubp, const struct dc_plane_address *address,
Signature · 6 lines
2.26.2 _______________________________________________ amd-gfx mailing list [email protected] https://lists.freedesktop.org/mailman/listinfo/amd-gfx
PATCH 26/27 drm/amd/display: Set/Reset avmute when disable/enable stream
In reply to Rodrigo SiqueiraFrom: Jinze Xu <[email protected]>
[Why]
When disconnect fe from be, something such as unstable clock may cause garbage occurs.
[How]
Send set avmute at the beginning of disable stream and send reset avmute at the end of enable stream.
--- drivers/gpu/drm/amd/display/dc/core/dc_link.c | 8 ++++++++ 1 file changed, 8 insertions(+)
drivers/gpu/drm/amd/display/dc/core/dc_link.c +8 -0
@@ -3244,6 +3244,10 @@ void core_link_enable_stream(dp_set_dsc_enable (pipe_ctx, true); } + +if (pipe_ctx->stream->signal ==SIGNAL_TYPE_HDMI_TYPE_A ) { +core_link_set_avmute (pipe_ctx, false); + } }void core_link_disable_stream (struct pipe_ctx *pipe_ctx)
@@ -3256,6 +3260,10 @@ void core_link_disable_stream(struct pipe_ctx *pipe_ctx) dc_is_virtual_signal(pipe_ctx->stream->signal)) return; +if (pipe_ctx->stream->signal ==SIGNAL_TYPE_HDMI_TYPE_A ) { +core_link_set_avmute (pipe_ctx, true); + } +#if defined(CONFIG_DRM_AMD_DC_HDCP )update_psp_stream_config (pipe_ctx, true);#endif
Signature · 6 lines
2.26.2 _______________________________________________ amd-gfx mailing list [email protected] https://lists.freedesktop.org/mailman/listinfo/amd-gfx
PATCH 27/27 drm/amd/display: FW Release 1.0.11
In reply to Rodrigo SiqueiraFrom: Anthony Koo <[email protected]>
--- drivers/gpu/drm/amd/display/dmub/inc/dmub_fw_meta.h | 2 ++ drivers/gpu/drm/amd/display/dmub/inc/dmub_rb.h | 6 ++++-- 2 files changed, 6 insertions(+), 2 deletions(-)
drivers/gpu/drm/amd/display/dmub/inc/dmub_fw_meta.h +2 -0
@@ -45,11 +45,13 @@* @magic_value: magic value identifying DMUB firmware meta info * @fw_region_size: size of the firmware state region * @trace_buffer_size: size of the tracebuffer region +* @fw_version: the firmware version information */ struct dmub_fw_meta_info {uint32_t magic_value;uint32_t fw_region_size;uint32_t trace_buffer_size; +uint32_t fw_version; };/* Ensure that the structure remains 64 bytes. */
drivers/gpu/drm/amd/display/dmub/inc/dmub_rb.h +4 -2
@@ -37,6 +37,8 @@ struct dmub_rb_init_params {void *ctx;void *base_address;uint32_t capacity; +uint32_t read_ptr; +uint32_t write_ptr; };struct dmub_rb {
@@ -141,8 +143,8 @@ static inline void dmub_rb_init(struct dmub_rb *rb, { rb->base_address = init_params->base_address; rb->capacity = init_params->capacity; - rb->rptr =0 ; - rb->wrpt =0 ; + rb->rptr = init_params->read_ptr; + rb->wrpt = init_params->write_ptr; }#if defined(__cplusplus)
Signature · 6 lines
2.26.2 _______________________________________________ amd-gfx mailing list [email protected] https://lists.freedesktop.org/mailman/listinfo/amd-gfx