Skip to contentSkip to conversation

iio: imu: bmi160: added regulator and mount-matrix support

PATCH New Jonathan Albrieux 1 participant 5 messages May 18, 2020

Subsystems (2)
lore
Share & tools
lore
#0 lore raw

cover iio: imu: bmi160: added regulator and mount-matrix support

Convert txt format documentation to yaml.
Add documentation about vdd-supply, vddio-supply and mount-matrix.

Add vdd-supply and vddio-supply support. Without this support, vdd and vddio should be set to always-on in device tree.

Add mount-matrix binding support. As chip could have different orientations a mount matrix support is needed to correctly translate these differences

Jonathan Albrieux (4):
dt-bindings: iio: imu: bmi160: convert txt format to yaml
dt-bindings: iio: imu: bmi160: add regulators and mount-matrix
iio: imu: bmi160: added regulator support
iio: imu: bmi160: added mount-matrix support

 .../devicetree/bindings/iio/imu/bmi160.txt    |  37 ------
 .../devicetree/bindings/iio/imu/bmi160.yaml   | 105 ++++++++++++++++++
 drivers/iio/imu/bmi160/bmi160.h               |   3 +
 drivers/iio/imu/bmi160/bmi160_core.c          |  47 +++++++-
 4 files changed, 154 insertions(+), 38 deletions(-)
 delete mode 100644 Documentation/devicetree/bindings/iio/imu/bmi160.txt
 create mode 100644 Documentation/devicetree/bindings/iio/imu/bmi160.yaml
Signature · 1 line
2.17.1
#1 lore raw

PATCH 1/4 dt-bindings: iio: imu: bmi160: convert txt format to yaml

Converts documentation from txt format to yaml

---
 .../devicetree/bindings/iio/imu/bmi160.txt    | 37 --------
 .../devicetree/bindings/iio/imu/bmi160.yaml   | 84 +++++++++++++++++++
 2 files changed, 84 insertions(+), 37 deletions(-)
 delete mode 100644 Documentation/devicetree/bindings/iio/imu/bmi160.txt
 create mode 100644 Documentation/devicetree/bindings/iio/imu/bmi160.yaml
Documentation/devicetree/bindings/iio/imu/bmi160.txt deleted +0 -37
deleted file mode 100644
index 900c169de00f..000000000000
@@ -1,37 +0,0 @@
-Bosch BMI160 - Inertial Measurement Unit with Accelerometer, Gyroscope
-and externally connectable Magnetometer
-
-https://www.bosch-sensortec.com/bst/products/all_products/bmi160
-
-Required properties:
- - compatible : should be "bosch,bmi160"
- - reg : the I2C address or SPI chip select number of the sensor
- - spi-max-frequency : set maximum clock frequency (only for SPI)
-
-Optional properties:
- - interrupts : interrupt mapping for IRQ
- - interrupt-names : set to "INT1" if INT1 pin should be used as interrupt
-   input, set to "INT2" if INT2 pin should be used instead
- - drive-open-drain : set if the specified interrupt pin should be configured as
-   open drain. If not set, defaults to push-pull.
-
-Examples:
-
-bmi160@68 {
-	compatible = "bosch,bmi160";
-	reg = <0x68>;
-
-	interrupt-parent = <&gpio4>;
-	interrupts = <12 IRQ_TYPE_EDGE_RISING>;
-	interrupt-names = "INT1";
-};
-
-bmi160@0 {
-	compatible = "bosch,bmi160";
-	reg = <0>;
-	spi-max-frequency = <10000000>;
-
-	interrupt-parent = <&gpio2>;
-	interrupts = <12 IRQ_TYPE_LEVEL_LOW>;
-	interrupt-names = "INT2";
-};
Documentation/devicetree/bindings/iio/imu/bmi160.yaml new file +84 -0

84 lines not on this page · raw message

Signature · 1 line
2.17.1
#2 lore raw

PATCH 2/4 dt-bindings: iio: imu: bmi160: add regulators and mount-matrix

In reply to Jonathan Albrieux

Add vdd-supply and vddio-supply support.
Add mount-matrix support.

---
 .../devicetree/bindings/iio/imu/bmi160.yaml   | 21 +++++++++++++++++++
 1 file changed, 21 insertions(+)
Documentation/devicetree/bindings/iio/imu/bmi160.yaml +21 -0
index 6b464ce5ed0b..5b13af7a209f 100644
@@ -46,6 +46,21 @@ properties:
       set if the specified interrupt pin should be configured as
       open drain. If not set, defaults to push-pull.
 
+  vdd-supply:
+    maxItems: 1
+    description: |
+      an optional regulator that needs to be on to provide VDD power to
+      the sensor.
+
+  vddio-supply:
+    maxItems: 1
+    description: |
+      an optional regulator that needs to be on to provide the VDD IO power to
+      the sensor.
+
+  mount-matrix:
+    description: an optional 3x3 mounting rotation matrix
+
 required:
   - compatible
   - reg
@@ -61,9 +76,15 @@ examples:
         bmi160@68 {
                 compatible = "bosch,bmi160";
                 reg = <0x68>;
+                vdd-supply = <&pm8916_l17>;
+                vddio-supply = <&pm8916_l6>;
                 interrupt-parent = <&gpio4>;
                 interrupts = <12 1>;
                 interrupt-names = "INT1";
+                mount-matrix = "0", "1", "0",
+                               "-1", "0", "0",
+                               "0", "0", "1";
+                };
         };
   - |
     // Example for SPI
Signature · 1 line
2.17.1
#3 lore raw

PATCH 3/4 iio: imu: bmi160: added regulator support

In reply to Jonathan Albrieux
---
 drivers/iio/imu/bmi160/bmi160.h      |  2 ++
 drivers/iio/imu/bmi160/bmi160_core.c | 27 ++++++++++++++++++++++++++-
 2 files changed, 28 insertions(+), 1 deletion(-)
drivers/iio/imu/bmi160/bmi160.h +2 -0
index 621f5309d735..923c3b274fde 100644
@@ -3,10 +3,12 @@
 #define BMI160_H_
 
 #include <linux/iio/iio.h>
+#include <linux/regulator/consumer.h>
 
 struct bmi160_data {
 	struct regmap *regmap;
 	struct iio_trigger *trig;
+	struct regulator_bulk_data supplies[2];
 };
 
 extern const struct regmap_config bmi160_regmap_config;
drivers/iio/imu/bmi160/bmi160_core.c +26 -1
index 6af65d6f1d28..9bbe0d8e6720 100644
@@ -15,6 +15,7 @@
 #include <linux/delay.h>
 #include <linux/irq.h>
 #include <linux/of_irq.h>
+#include <linux/regulator/consumer.h>
 
 #include <linux/iio/iio.h>
 #include <linux/iio/triggered_buffer.h>
@@ -709,6 +710,12 @@ static int bmi160_chip_init(struct bmi160_data *data, bool use_spi)
 	unsigned int val;
 	struct device *dev = regmap_get_device(data->regmap);
 
+	ret = regulator_bulk_enable(ARRAY_SIZE(data->supplies), data->supplies);
+	if (ret) {
+		dev_err(dev, "Failed to enable regulators: %d\n", ret);
+		return ret;
+	}
+
 	ret = regmap_write(data->regmap, BMI160_REG_CMD, BMI160_CMD_SOFTRESET);
 	if (ret)
 		return ret;
@@ -793,9 +800,17 @@ int bmi160_probe_trigger(struct iio_dev *indio_dev, int irq, u32 irq_type)
 static void bmi160_chip_uninit(void *data)
 {
 	struct bmi160_data *bmi_data = data;
+	struct device *dev = regmap_get_device(bmi_data->regmap);
+	int ret;
 
 	bmi160_set_mode(bmi_data, BMI160_GYRO, false);
 	bmi160_set_mode(bmi_data, BMI160_ACCEL, false);
+
+	ret = regulator_bulk_disable(ARRAY_SIZE(bmi_data->supplies),
+				     bmi_data->supplies);
+	if (ret) {
+		dev_err(dev, "Failed to disable regulators: %d\n", ret);
+	}
 }
 
 int bmi160_core_probe(struct device *dev, struct regmap *regmap,
@@ -815,6 +830,16 @@ int bmi160_core_probe(struct device *dev, struct regmap *regmap,
 	dev_set_drvdata(dev, indio_dev);
 	data->regmap = regmap;
 
+	data->supplies[0].supply = "vdd";
+	data->supplies[1].supply = "vddio";
+	ret = devm_regulator_bulk_get(dev,
+				      ARRAY_SIZE(data->supplies),
+				      data->supplies);
+	if (ret) {
+		dev_err(dev, "Failed to get regulators: %d\n", ret);
+		return ret;
+	}
+
 	ret = bmi160_chip_init(data, use_spi);
 	if (ret)
 		return ret;
@@ -853,6 +878,6 @@ int bmi160_core_probe(struct device *dev, struct regmap *regmap,
 }
 EXPORT_SYMBOL_GPL(bmi160_core_probe);
 
-MODULE_AUTHOR("Daniel Baluta <[email protected]");
+MODULE_AUTHOR("Daniel Baluta <[email protected]>");
 MODULE_DESCRIPTION("Bosch BMI160 driver");
 MODULE_LICENSE("GPL v2");
Signature · 1 line
2.17.1
#4 lore raw

PATCH 4/4 iio: imu: bmi160: added mount-matrix support

In reply to Jonathan Albrieux

Add mount-matrix binding support. As chip could have different orientations a mount matrix support is needed to correctly translate these differences

---
 drivers/iio/imu/bmi160/bmi160.h      |  1 +
 drivers/iio/imu/bmi160/bmi160_core.c | 20 ++++++++++++++++++++
 2 files changed, 21 insertions(+)
drivers/iio/imu/bmi160/bmi160.h +1 -0
index 923c3b274fde..a82e040bd109 100644
@@ -9,6 +9,7 @@ struct bmi160_data {
 	struct regmap *regmap;
 	struct iio_trigger *trig;
 	struct regulator_bulk_data supplies[2];
+	struct iio_mount_matrix orientation;
 };
 
 extern const struct regmap_config bmi160_regmap_config;
drivers/iio/imu/bmi160/bmi160_core.c +20 -0
index 9bbe0d8e6720..78c8ca962359 100644
@@ -110,6 +110,7 @@
 		.storagebits = 16,				\
 		.endianness = IIO_LE,				\
 	},							\
+	.ext_info = bmi160_ext_info,				\
 }
 
 /* scan indexes follow DATA register order */
@@ -265,6 +266,20 @@ static const struct  bmi160_odr_item bmi160_odr_table[] = {
 	},
 };
 
+static const struct iio_mount_matrix *
+bmi160_get_mount_matrix(const struct iio_dev *indio_dev,
+			const struct iio_chan_spec *chan)
+{
+	struct bmi160_data *data = iio_priv(indio_dev);
+
+	return &data->orientation;
+}
+
+static const struct iio_chan_spec_ext_info bmi160_ext_info[] = {
+	IIO_MOUNT_MATRIX(IIO_SHARED_BY_DIR, bmi160_get_mount_matrix),
+	{ }
+};
+
 static const struct iio_chan_spec bmi160_channels[] = {
 	BMI160_CHANNEL(IIO_ACCEL, X, BMI160_SCAN_ACCEL_X),
 	BMI160_CHANNEL(IIO_ACCEL, Y, BMI160_SCAN_ACCEL_Y),
@@ -840,6 +855,11 @@ int bmi160_core_probe(struct device *dev, struct regmap *regmap,
 		return ret;
 	}
 
+	ret = iio_read_mount_matrix(dev, "mount-matrix",
+				    &data->orientation);
+	if (ret)
+		return ret;
+
 	ret = bmi160_chip_init(data, use_spi);
 	if (ret)
 		return ret;
Signature · 1 line
2.17.1