ARM: stm32: Re-enable KS8851 on DHCOM
Subsystems (3)
PATCH 1/5 ARM: stm32: Re-enable KS8851 on DHCOM
Since the KS8851 driver is now in, enable the Kconfig entry on DHCOM to make the second ethernet available.
--- configs/stm32mp15_dhcom_basic_defconfig | 1 + 1 file changed, 1 insertion(+)
configs/stm32mp15_dhcom_basic_defconfig +1 -0
@@ -101,6 +101,7 @@ CONFIG_SPI_FLASH_MTD=y CONFIG_SPL_SPI_FLASH_MTD=y CONFIG_DM_ETH=y CONFIG_DWC_ETH_QOS=y +CONFIG_KS8851_MLL=y CONFIG_PHY=y CONFIG_PHY_STM32_USBPHYC=y CONFIG_PINCONF=y
Signature · 1 line
2.25.1
PATCH 2/5 ARM: stm32: Hog GPIO PF7 high on DHCOR to unlock SPI NOR nWP
The SPI NOR nWP line is connected to GPIO PF7 on the SoM, pull the GPIO line high by default to clear SPI NOR WP.
--- arch/arm/dts/stm32mp15xx-dhcor-u-boot.dtsi | 9 +++++++++ configs/stm32mp15_dhcor_basic_defconfig | 1 + 2 files changed, 10 insertions(+)
arch/arm/dts/stm32mp15xx-dhcor-u-boot.dtsi +9 -0
@@ -21,6 +21,15 @@ }; }; +&gpiof { + snor-nwp { + gpio-hog; + gpios = <7 0>; + output-high; + line-name = "spi-nor-nwp"; + }; +}; + &i2c4 { u-boot,dm-pre-reloc; };
configs/stm32mp15_dhcor_basic_defconfig +1 -0
@@ -71,6 +71,7 @@ CONFIG_SPL_BLOCK_CACHE=y CONFIG_DFU_MMC=y CONFIG_DFU_RAM=y CONFIG_DFU_VIRT=y +CONFIG_GPIO_HOG=y CONFIG_DM_HWSPINLOCK=y CONFIG_HWSPINLOCK_STM32=y CONFIG_DM_I2C=y
Signature · 1 line
2.25.1
PATCH 2/5 ARM: stm32: Hog GPIO PF7 high on DHCOR to unlock SPI NOR nWP
Hi Marek,
Quoted 6 lines
From: Marek Vasut <[email protected]>
Sent: mardi 26 mai 2020 04:30The SPI NOR nWP line is connected to GPIO PF7 on the SoM, pull the GPIO line high by default to clear SPI NOR WP.
Quoted 8 lines
Signed-off-by Marek Vasut <[email protected]>Cc Patrick Delaunay <[email protected]>Cc Patrice Chotard <[email protected]>--- arch/arm/dts/stm32mp15xx-dhcor-u-boot.dtsi | 9 +++++++++ configs/stm32mp15_dhcor_basic_defconfig | 1 + 2 files changed, 10 insertions(+)
Thanks
Patrick
PATCH 3/5 ARM: dts: stm32: Add alternate pinmux for I2C2 pins
In reply to Marek VasutAdd another mux option for I2C2 pins, this is used on AV96 board.
--- arch/arm/dts/stm32mp15-pinctrl.dtsi | 17 +++++++++++++++++ 1 file changed, 17 insertions(+)
arch/arm/dts/stm32mp15-pinctrl.dtsi +17 -0
@@ -357,6 +357,23 @@ }; }; + i2c2_pins_c: i2c2-4 { + pins { + pinmux = <STM32_PINMUX('F', 1, AF4)>, /* I2C2_SCL */ + <STM32_PINMUX('H', 5, AF4)>; /* I2C2_SDA */ + bias-disable; + drive-open-drain; + slew-rate = <0>; + }; + }; + + i2c2_pins_sleep_c: i2c2-5 { + pins { + pinmux = <STM32_PINMUX('F', 1, ANALOG)>, /* I2C2_SCL */ + <STM32_PINMUX('H', 5, ANALOG)>; /* I2C2_SDA */ + }; + }; + i2c5_pins_a: i2c5-0 { pins { pinmux = <STM32_PINMUX('A', 11, AF4)>, /* I2C5_SCL */
Signature · 1 line
2.25.1
PATCH 3/5 ARM: dts: stm32: Add alternate pinmux for I2C2 pins
Hi Marek,
Quoted 12 lines
From: Marek Vasut <[email protected]>
Sent: mardi 26 mai 2020 04:30Add another mux option for I2C2 pins, this is used on AV96 board.
Signed-off-by Marek Vasut <[email protected]>Cc Patrick Delaunay <[email protected]>Cc Patrice Chotard <[email protected]>--- arch/arm/dts/stm32mp15-pinctrl.dtsi | 17 +++++++++++++++++ 1 file changed, 17 insertions(+)
Thanks
Patrick
PATCH 4/5 ARM: dts: stm32: Repair I2C2 operation on AV96
In reply to Marek VasutThe I2C2 uses different pinmux on AV96, use correct pinmux and also add comments about the I2C being present on the "low-speed" expansion connector X6.
--- arch/arm/dts/stm32mp15xx-dhcor-avenger96.dts | 6 +++--- 1 file changed, 3 insertions(+), 3 deletions(-)
arch/arm/dts/stm32mp15xx-dhcor-avenger96.dts +3 -3
@@ -107,7 +107,7 @@ }; }; -&i2c1 { +&i2c1 { /* X6 I2C1 */ pinctrl-names = "default"; pinctrl-0 = <&i2c1_pins_b>; i2c-scl-rising-time-ns = <185>;
@@ -117,9 +117,9 @@ /delete-property/dma-names; }; -&i2c2 { +&i2c2 { /* X6 I2C2 */ pinctrl-names = "default"; - pinctrl-0 = <&i2c2_pins_b1 &i2c2_pins_b2>; + pinctrl-0 = <&i2c2_pins_c>; i2c-scl-rising-time-ns = <185>; i2c-scl-falling-time-ns = <20>; status = "okay";
Signature · 1 line
2.25.1
PATCH 4/5 ARM: dts: stm32: Repair I2C2 operation on AV96
Quoted 7 lines
From: Marek Vasut <[email protected]>
Sent: mardi 26 mai 2020 04:30The I2C2 uses different pinmux on AV96, use correct pinmux and also add comments about the I2C being present on the "low-speed" expansion connector X6.
Quoted 7 lines
Signed-off-by Marek Vasut <[email protected]>Cc Patrick Delaunay <[email protected]>Cc Patrice Chotard <[email protected]>--- arch/arm/dts/stm32mp15xx-dhcor-avenger96.dts | 6 +++--- 1 file changed, 3 insertions(+), 3 deletions(-)
Thanks
Patrick
PATCH 5/5 ARM: dts: stm32: Disable SDR104 mode on AV96
In reply to Marek VasutDisable SDR104 mode until we know it is really stable.
--- arch/arm/dts/stm32mp15xx-dhcor-avenger96.dts | 1 - 1 file changed, 1 deletion(-)
arch/arm/dts/stm32mp15xx-dhcor-avenger96.dts +0 -1
@@ -144,7 +144,6 @@ st,sig-dir; st,neg-edge; st,use-ckin; - sd-uhs-sdr104; bus-width = <4>; vmmc-supply = <&vdd_sd>; vqmmc-supply = <&sd_switch>;
Signature · 1 line
2.25.1
PATCH 5/5 ARM: dts: stm32: Disable SDR104 mode on AV96
Hi Marek,
Quoted 12 lines
From: Marek Vasut <[email protected]>
Sent: mardi 26 mai 2020 04:30Disable SDR104 mode until we know it is really stable.
Signed-off-by Marek Vasut <[email protected]>Cc Patrick Delaunay <[email protected]>Cc Patrice Chotard <[email protected]>--- arch/arm/dts/stm32mp15xx-dhcor-avenger96.dts | 1 - 1 file changed, 1 deletion(-)
Thanks
Patrick
PATCH 5/5 ARM: dts: stm32: Disable SDR104 mode on AV96
Quoted 1 line · Patrick DELAUNAY
Hi Marek,
Hi,
Quoted 13 lines
Quoted 12 lines
From: Marek Vasut <[email protected]>
Sent: mardi 26 mai 2020 04:30Disable SDR104 mode until we know it is really stable.
Signed-off-by Marek Vasut <[email protected]>Cc Patrick Delaunay <[email protected]>Cc Patrice Chotard <[email protected]>--- arch/arm/dts/stm32mp15xx-dhcor-avenger96.dts | 1 - 1 file changed, 1 deletion(-)
Quoted 1 line
Reviewed-by Patrick Delaunay <[email protected]>
This is for 2020.07 , it's the remaining stuff which fell through the cracks . And then that's it :)
PATCH 5/5 ARM: dts: stm32: Disable SDR104 mode on AV96
Hi :qrekm
Quoted 21 lines
From: Marek Vasut <[email protected]>
Sent: mercredi 27 mai 2020 19:48Quoted 1 line · Patrick DELAUNAY
Hi Marek,
Hi,
Quoted 13 lines
Quoted 12 lines
From: Marek Vasut <[email protected]>
Sent: mardi 26 mai 2020 04:30Disable SDR104 mode until we know it is really stable.
Signed-off-by Marek Vasut <[email protected]>Cc Patrick Delaunay <[email protected]>Cc Patrice Chotard <[email protected]>--- arch/arm/dts/stm32mp15xx-dhcor-avenger96.dts | 1 - 1 file changed, 1 deletion(-)
Quoted 4 lines
Quoted 1 line
Reviewed-by Patrick Delaunay <[email protected]>This is for 2020.07 , it's the remaining stuff which fell through the cracks . And then that's it :)
Sure.
For the serie:
Applied to u-boot-stm/master, thanks!
And I am preparing the pull request for v2020.07-rc4.
Regards
Patrick
PATCH 5/5 ARM: dts: stm32: Disable SDR104 mode on AV96
Quoted 1 line · Patrick DELAUNAY
Hi :qrekm
Hi,
Quoted 26 lines
Quoted 21 lines
From: Marek Vasut <[email protected]>
Sent: mercredi 27 mai 2020 19:48Quoted 1 line · Patrick DELAUNAY
Hi Marek,
Hi,
Quoted 13 lines
Quoted 12 lines
From: Marek Vasut <[email protected]>
Sent: mardi 26 mai 2020 04:30Disable SDR104 mode until we know it is really stable.
Signed-off-by Marek Vasut <[email protected]>Cc Patrick Delaunay <[email protected]>Cc Patrice Chotard <[email protected]>--- arch/arm/dts/stm32mp15xx-dhcor-avenger96.dts | 1 - 1 file changed, 1 deletion(-)Quoted 4 lines
Quoted 1 line
Reviewed-by Patrick Delaunay <[email protected]>This is for 2020.07 , it's the remaining stuff which fell through the cracks . And then that's it :)
Quoted 7 lines
Sure.
For the serie:
Applied to u-boot-stm/master, thanks!
And I am preparing the pull request for v2020.07-rc4.
Thanks
Signature · 2 lines
Best regards, Marek Vasut
PATCH 1/5 ARM: stm32: Re-enable KS8851 on DHCOM
In reply to Marek VasutHi Marek,
Quoted 7 lines
From: Marek Vasut <[email protected]>
Sent: mardi 26 mai 2020 04:30
To: u-boot at lists.denx.deSince the KS8851 driver is now in, enable the
Kconfigentry on DHCOM to make the second ethernet available.
Quoted 7 lines
Signed-off-by Marek Vasut <[email protected]>Cc Patrick Delaunay <[email protected]>Cc Patrice Chotard <[email protected]>--- configs/stm32mp15_dhcom_basic_defconfig | 1 + 1 file changed, 1 insertion(+)
Thanks
Patrick