Skip to contentSkip to conversation

Add Rockchip RK3399 USB3.0 Host support

PATCH In review Frank Wang 7 participants 24 messages May 26, 2020 – Jun 1, 2020 4 messages not in the archive

Subsystems (8)
lore
Share & tools
lore

Frank Wang

author
#0 lore raw

v6 cover Add Rockchip RK3399 USB3.0 Host support

This series add quirks for DWC3 and add Rockchip RK3399 USB3.0 host support.

The function has been tested pass on rk3399-evb and roc-rk3399-pc board.

For V6 update:
- Use [PATCH v6 04/16] instead of [PATCH v5 05/16] to fix that the current Generic PHY subsystem is unable to find PHY if the PHY node is not part of the root structure.
- Add 'Reviewed-by' tag for all patches except [PATCH v6 04/16].

For V5 update:
- Fix dwc3-generic driver followed Marek's comments for [PATCH v4 12/16].
- Add 'Reviewed-by' and 'Tested-by' tag for [PATCH v4 07/16] and [PATCH v4 08/16].

For V4 update:
- Collect Jagan's all fixed patches [1].
- Amend specific u-boot changes from dts to dtsi for [PATCH v3 6/7].

For V3 update:
- Fix compile error for [PATCH v2 1/9].
- Use Jagan's Type-C driver instead of [PATCH v2 5/9].
- Cleanup dts changes for [PATCH v2 7/9].
- Cleanup config changes for [PATCH v2 8/9] and [PATCH v2 9/9].

For V2 update:
- Amend type-c driver followed Jagan's comments for [PATCH 5/8].
- Fix dts commit for [PATCH 7/8].
- Split RK3399 default config for [PATCH 8/8].
- Add 'Reviewed-by' tag for [PATCH 1/8], [PATCH 2/8] and [PATCH 3/8].

[1] https://patchwork.ozlabs.org/project/uboot/cover/20200506075025.1677-1-jagan-dyjBcgdgk7Pe9wHmmfpqLFaTQe2KTcn/@public.gmane.org

BR,
Frank

Frank Wang (8):
arm: mach-rockchip: bind sub-nodes for rk3399_syscon
usb: dwc3: add dis_enblslpm_quirk
usb: dwc3: add dis_u2_freeclk_exists_quirk
usb: dwc3: amend UTMI/UTMIW phy interface setup
usb: dwc3: add make compatible for rockchip platform
driver: usb: drop legacy rockchip xhci driver
ARM: dts: rk3399-evb: usb3.0 host support
configs: evb-rk3399: update support usb3.0 host

Jagan Teki (8):
clk: rk3399: Enable/Disable the USB2PHY clk
clk: rk3399: Set empty for TCPHY assigned-clocks
clk: rk3399: Enable/Disable TCPHY clocks
phy: rockchip: Add Rockchip USB2PHY driver
phy: rockchip: Add Rockchip USB TypeC PHY driver
usb: dwc3: Add disable u2mac linestate check quirk
usb: dwc3: Enable AutoRetry feature in the controller
roc-rk3399-pc: Enable USB3.0 Host

 arch/arm/dts/rk3399-evb-u-boot.dtsi           |  13 +
 arch/arm/mach-rockchip/rk3399/syscon_rk3399.c |   3 +
 configs/evb-rk3399_defconfig                  |   6 +
 configs/roc-pc-mezzanine-rk3399_defconfig     |   5 +
 configs/roc-pc-rk3399_defconfig               |   6 +
 drivers/Makefile                              |   1 +
 drivers/clk/rockchip/clk_rk3399.c             |  38 +
 drivers/phy/Kconfig                           |   1 +
 drivers/phy/rockchip/Kconfig                  |  21 +
 drivers/phy/rockchip/Makefile                 |   7 +
 drivers/phy/rockchip/phy-rockchip-inno-usb2.c | 312 +++++++
 drivers/phy/rockchip/phy-rockchip-typec.c     | 796 ++++++++++++++++++
 drivers/usb/common/common.c                   |  25 +
 drivers/usb/dwc3/core.c                       | 106 ++-
 drivers/usb/dwc3/core.h                       |  19 +
 drivers/usb/dwc3/dwc3-generic.c               |  33 +-
 drivers/usb/host/Kconfig                      |   9 -
 drivers/usb/host/Makefile                     |   1 -
 drivers/usb/host/xhci-rockchip.c              | 196 -----
 include/dwc3-uboot.h                          |   3 +
 include/linux/usb/phy.h                       |  18 +
 21 files changed, 1376 insertions(+), 243 deletions(-)
 create mode 100644 drivers/phy/rockchip/Kconfig
 create mode 100644 drivers/phy/rockchip/Makefile
 create mode 100644 drivers/phy/rockchip/phy-rockchip-inno-usb2.c
 create mode 100644 drivers/phy/rockchip/phy-rockchip-typec.c
 delete mode 100644 drivers/usb/host/xhci-rockchip.c
Signature · 1 line
2.17.1
#1 lore raw

PATCH v6 1/16 clk: rk3399: Enable/Disable the USB2PHY clk

From: Jagan Teki <[email protected]>

Enable/Disable the USB2PHY clk for rk3399.

CLK is clear in enable and set in disable functionality.

---
 drivers/clk/rockchip/clk_rk3399.c | 12 ++++++++++++
 1 file changed, 12 insertions(+)
drivers/clk/rockchip/clk_rk3399.c +12 -0
index 5fb72d83c2..b53f2f984e 100644
@@ -1091,6 +1091,12 @@ static int rk3399_clk_enable(struct clk *clk)
 	case SCLK_MACREF_OUT:
 		rk_clrreg(&priv->cru->clkgate_con[5], BIT(6));
 		break;
+	case SCLK_USB2PHY0_REF:
+		rk_clrreg(&priv->cru->clkgate_con[6], BIT(5));
+		break;
+	case SCLK_USB2PHY1_REF:
+		rk_clrreg(&priv->cru->clkgate_con[6], BIT(6));
+		break;
 	case ACLK_GMAC:
 		rk_clrreg(&priv->cru->clkgate_con[32], BIT(0));
 		break;
@@ -1167,6 +1173,12 @@ static int rk3399_clk_disable(struct clk *clk)
 	case SCLK_MACREF_OUT:
 		rk_setreg(&priv->cru->clkgate_con[5], BIT(6));
 		break;
+	case SCLK_USB2PHY0_REF:
+		rk_setreg(&priv->cru->clkgate_con[6], BIT(5));
+		break;
+	case SCLK_USB2PHY1_REF:
+		rk_setreg(&priv->cru->clkgate_con[6], BIT(6));
+		break;
 	case ACLK_GMAC:
 		rk_setreg(&priv->cru->clkgate_con[32], BIT(0));
 		break;
Signature · 1 line
2.17.1

A message that is not in the archive (sent off-list or not yet received): 20200526033220.20047-1-frank.wang-TNX95d0MmH7DzftRWevZcw@public.gmane.org

author
#3 lore raw

PATCH v6 2/16 clk: rk3399: Set empty for TCPHY assigned-clocks

From: Jagan Teki <jagan-dyjBcgdgk7Pe9wHmmfpqLFaTQe2KTcn/@public.gmane.org>

Due to v5.7-rc1 sync the SD controller nodes in rk3399.dtsi have SCLK_UPHY0_TCPDCORE, SCLK_UPHY1_TCPDCORE assigned-clocks which are usually required for Linux and don't require to handle them in U-Boot.

  assigned-clocks = <&cru SCLK_UPHY0_TCPDCORE>;
  assigned-clocks = <&cru SCLK_UPHY1_TCPDCORE>;

So, mark them as empty in clock otherwise device probe on those typec phy driver would fail.

---
 drivers/clk/rockchip/clk_rk3399.c | 2 ++
 1 file changed, 2 insertions(+)
drivers/clk/rockchip/clk_rk3399.c +2 -0
index b53f2f984e..98fc6a3267 100644
@@ -997,6 +997,8 @@ static ulong rk3399_clk_set_rate(struct clk *clk, ulong rate)
 	case ACLK_VOP1:
 	case HCLK_VOP1:
 	case HCLK_SD:
+	case SCLK_UPHY0_TCPDCORE:
+	case SCLK_UPHY1_TCPDCORE:
 		/**
 		 * assigned-clocks handling won't require for vopl, so
 		 * return 0 to satisfy clk_set_defaults during device probe.
Signature · 1 line
2.17.1
author
#4 lore raw

PATCH v6 3/16 clk: rk3399: Enable/Disable TCPHY clocks

In reply to a message not in the archive

From: Jagan Teki <jagan-dyjBcgdgk7Pe9wHmmfpqLFaTQe2KTcn/@public.gmane.org>

Enable/Disable TCPHY clock for rk3399 platform.

---
 drivers/clk/rockchip/clk_rk3399.c | 24 ++++++++++++++++++++++++
 1 file changed, 24 insertions(+)
drivers/clk/rockchip/clk_rk3399.c +24 -0
index 98fc6a3267..06232f1903 100644
@@ -1144,6 +1144,18 @@ static int rk3399_clk_enable(struct clk *clk)
 	case HCLK_HOST1_ARB:
 		rk_clrreg(&priv->cru->clksel_con[20], BIT(8));
 		break;
+	case SCLK_UPHY0_TCPDPHY_REF:
+		rk_clrreg(&priv->cru->clkgate_con[13], BIT(4));
+		break;
+	case SCLK_UPHY0_TCPDCORE:
+		rk_clrreg(&priv->cru->clkgate_con[13], BIT(5));
+		break;
+	case SCLK_UPHY1_TCPDPHY_REF:
+		rk_clrreg(&priv->cru->clkgate_con[13], BIT(6));
+		break;
+	case SCLK_UPHY1_TCPDCORE:
+		rk_clrreg(&priv->cru->clkgate_con[13], BIT(7));
+		break;
 	case SCLK_PCIEPHY_REF:
 		rk_clrreg(&priv->cru->clksel_con[18], BIT(10));
 		break;
@@ -1226,6 +1238,18 @@ static int rk3399_clk_disable(struct clk *clk)
 	case HCLK_HOST1_ARB:
 		rk_setreg(&priv->cru->clksel_con[20], BIT(8));
 		break;
+	case SCLK_UPHY0_TCPDPHY_REF:
+		rk_setreg(&priv->cru->clkgate_con[13], BIT(4));
+		break;
+	case SCLK_UPHY0_TCPDCORE:
+		rk_setreg(&priv->cru->clkgate_con[13], BIT(5));
+		break;
+	case SCLK_UPHY1_TCPDPHY_REF:
+		rk_setreg(&priv->cru->clkgate_con[13], BIT(6));
+		break;
+	case SCLK_UPHY1_TCPDCORE:
+		rk_setreg(&priv->cru->clkgate_con[13], BIT(7));
+		break;
 	case SCLK_PCIEPHY_REF:
 		rk_clrreg(&priv->cru->clksel_con[18], BIT(10));
 		break;
Signature · 1 line
2.17.1
author
#5 lore raw

PATCH v6 4/16 arm: mach-rockchip: bind sub-nodes for rk3399_syscon

In reply to a message not in the archive

There are some sub-nodes under the grf DT, so add bind callback function in rk3399 syscon driver to scan them recursively.

---
 arch/arm/mach-rockchip/rk3399/syscon_rk3399.c | 3 +++
 1 file changed, 3 insertions(+)
arch/arm/mach-rockchip/rk3399/syscon_rk3399.c +3 -0
index 259ca44d68..f27b0ced82 100644
@@ -20,6 +20,9 @@ static const struct udevice_id rk3399_syscon_ids[] = {
 U_BOOT_DRIVER(syscon_rk3399) = {
 	.name = "rk3399_syscon",
 	.id = UCLASS_SYSCON,
+#if !CONFIG_IS_ENABLED(OF_PLATDATA)
+	.bind = dm_scan_fdt_dev,
+#endif
 	.of_match = rk3399_syscon_ids,
 };
 
Signature · 1 line
2.17.1
Reviewed-by Tested-by on v6 4/16
#6 lore raw

Re: [PATCH v6 04/16] arm: mach-rockchip: bind sub-nodes for rk3399_syscon

Quoted 14 lines · Frank Wang

There are some sub-nodes under the grf DT, so add bind callback function in rk3399 syscon driver to scan them recursively.

---
 arch/arm/mach-rockchip/rk3399/syscon_rk3399.c | 3 +++
 1 file changed, 3 insertions(+)
arch/arm/mach-rockchip/rk3399/syscon_rk3399.c +0 -0
index 259ca44d68..f27b0ced82 100644

arch/arm/mach-rockchip/rk3399/syscon_rk3399.c static const struct udevice_id rk3399_syscon_ids[] = { · line 25

Quoted 6 lines
arch/arm/mach-rockchip/rk3399/syscon_rk3399.c +3 -0
@@ -20,6 +20,9 @@ static const struct udevice_id rk3399_syscon_ids[] = {
 U_BOOT_DRIVER(syscon_rk3399) = {
        .name = "rk3399_syscon",
        .id = UCLASS_SYSCON,
+#if !CONFIG_IS_ENABLED(OF_PLATDATA)
+       .bind = dm_scan_fdt_dev,
+#endif
Reviewed-by on v6 4/16
#7 lore raw

Re: [PATCH v6 04/16] arm: mach-rockchip: bind sub-nodes for rk3399_syscon

In reply to Frank Wang
Quoted 4 lines · Frank Wang

There are some sub-nodes under the grf DT, so add bind callback function in rk3399 syscon driver to scan them recursively.

Thanks,
- Kever

Quoted 18 lines
---
  arch/arm/mach-rockchip/rk3399/syscon_rk3399.c | 3 +++
  1 file changed, 3 insertions(+)
arch/arm/mach-rockchip/rk3399/syscon_rk3399.c +3 -0
index 259ca44d68..f27b0ced82 100644
@@ -20,6 +20,9 @@ static const struct udevice_id rk3399_syscon_ids[] = {
  U_BOOT_DRIVER(syscon_rk3399) = {
  	.name = "rk3399_syscon",
  	.id = UCLASS_SYSCON,
+#if !CONFIG_IS_ENABLED(OF_PLATDATA)
+	.bind = dm_scan_fdt_dev,
+#endif
  	.of_match = rk3399_syscon_ids,
  };
 
author
#8 lore raw

PATCH v6 5/16 phy: rockchip: Add Rockchip USB2PHY driver

In reply to a message not in the archive

From: Jagan Teki <jagan-dyjBcgdgk7Pe9wHmmfpqLFaTQe2KTcn/@public.gmane.org>

Add Rockchip USB2PHY driver with initial support.

This will help to use it for EHCI controller in host mode, and USB 3.0 controller in otg mode.

More functionality like charge, vbus detection will add it in future changes.

---
 drivers/Makefile                              |   1 +
 drivers/phy/Kconfig                           |   1 +
 drivers/phy/rockchip/Kconfig                  |  14 +
 drivers/phy/rockchip/Makefile                 |   6 +
 drivers/phy/rockchip/phy-rockchip-inno-usb2.c | 312 ++++++++++++++++++
 5 files changed, 334 insertions(+)
 create mode 100644 drivers/phy/rockchip/Kconfig
 create mode 100644 drivers/phy/rockchip/Makefile
 create mode 100644 drivers/phy/rockchip/phy-rockchip-inno-usb2.c
drivers/Makefile +1 -0
index 4208750428..94e8c5da17 100644
@@ -91,6 +91,7 @@ obj-y += dfu/
 obj-$(CONFIG_PCH) += pch/
 obj-y += phy/allwinner/
 obj-y += phy/marvell/
+obj-y += phy/rockchip/
 obj-y += rtc/
 obj-y += scsi/
 obj-y += sound/
drivers/phy/Kconfig +1 -0
index 1e38c8741f..9c775107e9 100644
@@ -225,4 +225,5 @@ config PHY_MTK_TPHY
 	  multi-ports is first version, otherwise is second veriosn,
 	  so you can easily distinguish them by banks layout.
 
+source "drivers/phy/rockchip/Kconfig"
 endmenu
drivers/phy/rockchip/Kconfig new file +14 -0
new file mode 100644
index 0000000000..d73ac695e1
@@ -0,0 +1,14 @@
+#
+# Phy drivers for Rockchip platforms
+#
+
+menu "Rockchip PHY driver"
+
+config PHY_ROCKCHIP_INNO_USB2
+	bool "Rockchip INNO USB2PHY Driver"
+	depends on ARCH_ROCKCHIP
+	select PHY
+	help
+	  Support for Rockchip USB2.0 PHY with Innosilicon IP block.
+
+endmenu
drivers/phy/rockchip/Makefile new file +6 -0
new file mode 100644
index 0000000000..9b0cbc6acf
@@ -0,0 +1,6 @@
+# SPDX-License-Identifier: GPL-2.0+
+#
+# Copyright (C) 2020 Amarula Solutions(India)
+#
+
+obj-$(CONFIG_PHY_ROCKCHIP_INNO_USB2)	+= phy-rockchip-inno-usb2.o
drivers/phy/rockchip/phy-rockchip-inno-usb2.c new file +312 -0

312 lines not on this page · raw message

Signature · 1 line
2.17.1

A message that is not in the archive (sent off-list or not yet received): 20200526033355.20147-1-frank.wang-TNX95d0MmH7DzftRWevZcw@public.gmane.org

author
#10 lore raw

PATCH v6 6/16 phy: rockchip: Add Rockchip USB TypeC PHY driver

From: Jagan Teki <jagan-dyjBcgdgk7Pe9wHmmfpqLFaTQe2KTcn/@public.gmane.org>

Add USB TYPEC PHY driver for rockchip platform.

Referenced from Linux TypeC PHY driver, currently
supporting usb3-port and dp-port need to add it
in the future.

---
 drivers/phy/rockchip/Kconfig              |   7 +
 drivers/phy/rockchip/Makefile             |   1 +
 drivers/phy/rockchip/phy-rockchip-typec.c | 796 ++++++++++++++++++++++
 3 files changed, 804 insertions(+)
 create mode 100644 drivers/phy/rockchip/phy-rockchip-typec.c
drivers/phy/rockchip/Kconfig +7 -0
index d73ac695e1..84cc7c876d 100644
@@ -11,4 +11,11 @@ config PHY_ROCKCHIP_INNO_USB2
 	help
 	  Support for Rockchip USB2.0 PHY with Innosilicon IP block.
 
+config PHY_ROCKCHIP_TYPEC
+	bool "Rockchip TYPEC PHY Driver"
+	depends on ARCH_ROCKCHIP
+	select PHY
+	help
+	  Enable this to support the Rockchip USB TYPEC PHY.
+
 endmenu
drivers/phy/rockchip/Makefile +1 -0
index 9b0cbc6acf..95b2f8a3c0 100644
@@ -4,3 +4,4 @@
 #
 
 obj-$(CONFIG_PHY_ROCKCHIP_INNO_USB2)	+= phy-rockchip-inno-usb2.o
+obj-$(CONFIG_PHY_ROCKCHIP_TYPEC)	+= phy-rockchip-typec.o
drivers/phy/rockchip/phy-rockchip-typec.c new file +796 -0

796 lines not on this page · raw message

Signature · 1 line
2.17.1
author
#11 lore raw

PATCH v6 7/16 usb: dwc3: add dis_enblslpm_quirk

In reply to a message not in the archive

Add a quirk to clear the GUSB2PHYCFG.ENBLSLPM bit, which controls whether the PHY receives the suspend signal from the controller.

Refer to commit ec791d149bca("usb: dwc3: Add dis_enblslpm_quirk") in Linux Kernel.

---
 drivers/usb/dwc3/core.c | 6 ++++++
 drivers/usb/dwc3/core.h | 2 ++
 include/dwc3-uboot.h    | 1 +
 3 files changed, 9 insertions(+)
drivers/usb/dwc3/core.c +6 -0
index 0972e458eb..20be617fd4 100644
@@ -398,6 +398,9 @@ static void dwc3_phy_setup(struct dwc3 *dwc)
 	if (dwc->dis_u2_susphy_quirk)
 		reg &= ~DWC3_GUSB2PHYCFG_SUSPHY;
 
+	if (dwc->dis_enblslpm_quirk)
+		reg &= ~DWC3_GUSB2PHYCFG_ENBLSLPM;
+
 	dwc3_writel(dwc->regs, DWC3_GUSB2PHYCFG(0), reg);
 
 	mdelay(100);
@@ -719,6 +722,7 @@ int dwc3_uboot_init(struct dwc3_device *dwc3_dev)
 	dwc->dis_u3_susphy_quirk = dwc3_dev->dis_u3_susphy_quirk;
 	dwc->dis_u2_susphy_quirk = dwc3_dev->dis_u2_susphy_quirk;
 	dwc->dis_del_phy_power_chg_quirk = dwc3_dev->dis_del_phy_power_chg_quirk;
+	dwc->dis_enblslpm_quirk = dwc3_dev->dis_enblslpm_quirk;
 
 	dwc->tx_de_emphasis_quirk = dwc3_dev->tx_de_emphasis_quirk;
 	if (dwc3_dev->tx_de_emphasis)
@@ -926,6 +930,8 @@ void dwc3_of_parse(struct dwc3 *dwc)
 				"snps,dis_u2_susphy_quirk");
 	dwc->dis_del_phy_power_chg_quirk = dev_read_bool(dev,
 				"snps,dis-del-phy-power-chg-quirk");
+	dwc->dis_enblslpm_quirk = dev_read_bool(dev,
+				"snps,dis_enblslpm_quirk");
 	dwc->tx_de_emphasis_quirk = dev_read_bool(dev,
 				"snps,tx_de_emphasis_quirk");
 	tmp = dev_read_u8_array_ptr(dev, "snps,tx_de_emphasis", 1);
drivers/usb/dwc3/core.h +2 -0
index 7f45a9c459..e76e357f1e 100644
@@ -162,6 +162,7 @@
 /* Global USB2 PHY Configuration Register */
 #define DWC3_GUSB2PHYCFG_PHYSOFTRST	(1 << 31)
 #define DWC3_GUSB2PHYCFG_SUSPHY		(1 << 6)
+#define DWC3_GUSB2PHYCFG_ENBLSLPM	(1 << 8)
 #define DWC3_GUSB2PHYCFG_PHYIF(n)	((n) << 3)
 #define DWC3_GUSB2PHYCFG_PHYIF_MASK	DWC3_GUSB2PHYCFG_PHYIF(1)
 #define DWC3_GUSB2PHYCFG_USBTRDTIM(n)	((n) << 10)
@@ -822,6 +823,7 @@ struct dwc3 {
 	unsigned		dis_u3_susphy_quirk:1;
 	unsigned		dis_u2_susphy_quirk:1;
 	unsigned		dis_del_phy_power_chg_quirk:1;
+	unsigned		dis_enblslpm_quirk:1;
 
 	unsigned		tx_de_emphasis_quirk:1;
 	unsigned		tx_de_emphasis:2;
include/dwc3-uboot.h +1 -0
index ecae34bf06..98d51e05e1 100644
@@ -34,6 +34,7 @@ struct dwc3_device {
 	unsigned dis_u3_susphy_quirk;
 	unsigned dis_u2_susphy_quirk;
 	unsigned dis_del_phy_power_chg_quirk;
+	unsigned dis_enblslpm_quirk;
 	unsigned tx_de_emphasis_quirk;
 	unsigned tx_de_emphasis;
 	int index;
Signature · 1 line
2.17.1
author
#12 lore raw

PATCH v6 8/16 usb: dwc3: add dis_u2_freeclk_exists_quirk

In reply to a message not in the archive

Add a quirk to clear the GUSB2PHYCFG.U2_FREECLK_EXISTS bit, which specifies whether the USB2.0 PHY provides a free-running PHY clock, which is active when the clock control input is active.

Refer to commit 27f83eeb6b42("usb: dwc3: add dis_u2_freeclk_exists_quirk") in Linux Rockchip Kernel.

---
 drivers/usb/dwc3/core.c | 6 ++++++
 drivers/usb/dwc3/core.h | 2 ++
 include/dwc3-uboot.h    | 1 +
 3 files changed, 9 insertions(+)
drivers/usb/dwc3/core.c +6 -0
index 20be617fd4..3cb66515a2 100644
@@ -401,6 +401,9 @@ static void dwc3_phy_setup(struct dwc3 *dwc)
 	if (dwc->dis_enblslpm_quirk)
 		reg &= ~DWC3_GUSB2PHYCFG_ENBLSLPM;
 
+	if (dwc->dis_u2_freeclk_exists_quirk)
+		reg &= ~DWC3_GUSB2PHYCFG_U2_FREECLK_EXISTS;
+
 	dwc3_writel(dwc->regs, DWC3_GUSB2PHYCFG(0), reg);
 
 	mdelay(100);
@@ -723,6 +726,7 @@ int dwc3_uboot_init(struct dwc3_device *dwc3_dev)
 	dwc->dis_u2_susphy_quirk = dwc3_dev->dis_u2_susphy_quirk;
 	dwc->dis_del_phy_power_chg_quirk = dwc3_dev->dis_del_phy_power_chg_quirk;
 	dwc->dis_enblslpm_quirk = dwc3_dev->dis_enblslpm_quirk;
+	dwc->dis_u2_freeclk_exists_quirk = dwc3_dev->dis_u2_freeclk_exists_quirk;
 
 	dwc->tx_de_emphasis_quirk = dwc3_dev->tx_de_emphasis_quirk;
 	if (dwc3_dev->tx_de_emphasis)
@@ -932,6 +936,8 @@ void dwc3_of_parse(struct dwc3 *dwc)
 				"snps,dis-del-phy-power-chg-quirk");
 	dwc->dis_enblslpm_quirk = dev_read_bool(dev,
 				"snps,dis_enblslpm_quirk");
+	dwc->dis_u2_freeclk_exists_quirk = dev_read_bool(dev,
+				"snps,dis-u2-freeclk-exists-quirk");
 	dwc->tx_de_emphasis_quirk = dev_read_bool(dev,
 				"snps,tx_de_emphasis_quirk");
 	tmp = dev_read_u8_array_ptr(dev, "snps,tx_de_emphasis", 1);
drivers/usb/dwc3/core.h +2 -0
index e76e357f1e..c5e656885a 100644
@@ -161,6 +161,7 @@
 
 /* Global USB2 PHY Configuration Register */
 #define DWC3_GUSB2PHYCFG_PHYSOFTRST	(1 << 31)
+#define DWC3_GUSB2PHYCFG_U2_FREECLK_EXISTS	(1 << 30)
 #define DWC3_GUSB2PHYCFG_SUSPHY		(1 << 6)
 #define DWC3_GUSB2PHYCFG_ENBLSLPM	(1 << 8)
 #define DWC3_GUSB2PHYCFG_PHYIF(n)	((n) << 3)
@@ -824,6 +825,7 @@ struct dwc3 {
 	unsigned		dis_u2_susphy_quirk:1;
 	unsigned		dis_del_phy_power_chg_quirk:1;
 	unsigned		dis_enblslpm_quirk:1;
+	unsigned		dis_u2_freeclk_exists_quirk:1;
 
 	unsigned		tx_de_emphasis_quirk:1;
 	unsigned		tx_de_emphasis:2;
include/dwc3-uboot.h +1 -0
index 98d51e05e1..193d225d31 100644
@@ -35,6 +35,7 @@ struct dwc3_device {
 	unsigned dis_u2_susphy_quirk;
 	unsigned dis_del_phy_power_chg_quirk;
 	unsigned dis_enblslpm_quirk;
+	unsigned dis_u2_freeclk_exists_quirk;
 	unsigned tx_de_emphasis_quirk;
 	unsigned tx_de_emphasis;
 	int index;
Signature · 1 line
2.17.1
author
#13 lore raw

PATCH v6 9/16 usb: dwc3: Add disable u2mac linestate check quirk

In reply to a message not in the archive

From: Jagan Teki <jagan-dyjBcgdgk7Pe9wHmmfpqLFaTQe2KTcn/@public.gmane.org>

This patch adds a quirk to disable USB 2.0 MAC linestate check during HS transmit. Refer the dwc3 databook, we can use it for some special platforms if the linestate not reflect the expected line state(J) during transmission.

When use this quirk, the controller implements a fixed 40-bit TxEndDelay after the packet is given on UTMI and ignores the linestate during the transmit of a token (during token-to-token and token-to-data IPGAP).

On some rockchip platforms (e.g. rk3399), it requires to disable the u2mac linestate check to decrease the SSPLIT token to SETUP token inter-packet delay from 566ns to 466ns, and fix the issue that FS/LS devices not recognized if inserted through USB 3.0 HUB.

Reference from below Linux commit,

commit <65db7a0c9816> ("usb: dwc3: add disable u2mac linestate check quirk")

---
 drivers/usb/dwc3/core.c | 20 ++++++++++++++++++++
 drivers/usb/dwc3/core.h |  7 +++++++
 include/dwc3-uboot.h    |  1 +
 3 files changed, 28 insertions(+)
drivers/usb/dwc3/core.c +20 -0
index 3cb66515a2..dc92f471c1 100644
@@ -725,6 +725,7 @@ int dwc3_uboot_init(struct dwc3_device *dwc3_dev)
 	dwc->dis_u3_susphy_quirk = dwc3_dev->dis_u3_susphy_quirk;
 	dwc->dis_u2_susphy_quirk = dwc3_dev->dis_u2_susphy_quirk;
 	dwc->dis_del_phy_power_chg_quirk = dwc3_dev->dis_del_phy_power_chg_quirk;
+	dwc->dis_tx_ipgap_linecheck_quirk = dwc3_dev->dis_tx_ipgap_linecheck_quirk;
 	dwc->dis_enblslpm_quirk = dwc3_dev->dis_enblslpm_quirk;
 	dwc->dis_u2_freeclk_exists_quirk = dwc3_dev->dis_u2_freeclk_exists_quirk;
 
@@ -934,6 +935,8 @@ void dwc3_of_parse(struct dwc3 *dwc)
 				"snps,dis_u2_susphy_quirk");
 	dwc->dis_del_phy_power_chg_quirk = dev_read_bool(dev,
 				"snps,dis-del-phy-power-chg-quirk");
+	dwc->dis_tx_ipgap_linecheck_quirk = dev_read_bool(dev,
+				"snps,dis-tx-ipgap-linecheck-quirk");
 	dwc->dis_enblslpm_quirk = dev_read_bool(dev,
 				"snps,dis_enblslpm_quirk");
 	dwc->dis_u2_freeclk_exists_quirk = dev_read_bool(dev,
@@ -954,6 +957,7 @@ void dwc3_of_parse(struct dwc3 *dwc)
 int dwc3_init(struct dwc3 *dwc)
 {
 	int ret;
+	u32 reg;
 
 	dwc3_cache_hwparams(dwc);
 
@@ -975,6 +979,22 @@ int dwc3_init(struct dwc3 *dwc)
 		goto event_fail;
 	}
 
+	if (dwc->revision >= DWC3_REVISION_250A) {
+		reg = dwc3_readl(dwc->regs, DWC3_GUCTL1);
+
+		/*
+		 * Enable hardware control of sending remote wakeup
+		 * in HS when the device is in the L1 state.
+		 */
+		if (dwc->revision >= DWC3_REVISION_290A)
+			reg |= DWC3_GUCTL1_DEV_L1_EXIT_BY_HW;
+
+		if (dwc->dis_tx_ipgap_linecheck_quirk)
+			reg |= DWC3_GUCTL1_TX_IPGAP_LINECHECK_DIS;
+
+		dwc3_writel(dwc->regs, DWC3_GUCTL1, reg);
+	}
+
 	ret = dwc3_core_init_mode(dwc);
 	if (ret)
 		goto mode_fail;
drivers/usb/dwc3/core.h +7 -0
index c5e656885a..b510d8a983 100644
@@ -73,6 +73,7 @@
 #define DWC3_GCTL		0xc110
 #define DWC3_GEVTEN		0xc114
 #define DWC3_GSTS		0xc118
+#define DWC3_GUCTL1		0xc11c
 #define DWC3_GSNPSID		0xc120
 #define DWC3_GGPIO		0xc124
 #define DWC3_GUID		0xc128
@@ -159,6 +160,10 @@
 #define DWC3_GCTL_GBLHIBERNATIONEN	(1 << 1)
 #define DWC3_GCTL_DSBLCLKGTNG		(1 << 0)
 
+/* Global User Control 1 Register */
+#define DWC3_GUCTL1_TX_IPGAP_LINECHECK_DIS	BIT(28)
+#define DWC3_GUCTL1_DEV_L1_EXIT_BY_HW	BIT(24)
+
 /* Global USB2 PHY Configuration Register */
 #define DWC3_GUSB2PHYCFG_PHYSOFTRST	(1 << 31)
 #define DWC3_GUSB2PHYCFG_U2_FREECLK_EXISTS	(1 << 30)
@@ -771,6 +776,7 @@ struct dwc3 {
 #define DWC3_REVISION_260A	0x5533260a
 #define DWC3_REVISION_270A	0x5533270a
 #define DWC3_REVISION_280A	0x5533280a
+#define DWC3_REVISION_290A	0x5533290a
 
 	enum dwc3_ep0_next	ep0_next_event;
 	enum dwc3_ep0_state	ep0state;
@@ -824,6 +830,7 @@ struct dwc3 {
 	unsigned		dis_u3_susphy_quirk:1;
 	unsigned		dis_u2_susphy_quirk:1;
 	unsigned		dis_del_phy_power_chg_quirk:1;
+	unsigned		dis_tx_ipgap_linecheck_quirk:1;
 	unsigned		dis_enblslpm_quirk:1;
 	unsigned		dis_u2_freeclk_exists_quirk:1;
 
include/dwc3-uboot.h +1 -0
index 193d225d31..e08530ec4e 100644
@@ -34,6 +34,7 @@ struct dwc3_device {
 	unsigned dis_u3_susphy_quirk;
 	unsigned dis_u2_susphy_quirk;
 	unsigned dis_del_phy_power_chg_quirk;
+	unsigned dis_tx_ipgap_linecheck_quirk;
 	unsigned dis_enblslpm_quirk;
 	unsigned dis_u2_freeclk_exists_quirk;
 	unsigned tx_de_emphasis_quirk;
Signature · 1 line
2.17.1
author
#14 lore raw

PATCH v6 10/16 usb: dwc3: Enable AutoRetry feature in the controller

In reply to a message not in the archive

From: Jagan Teki <jagan-dyjBcgdgk7Pe9wHmmfpqLFaTQe2KTcn/@public.gmane.org>

By default when core sees any transaction error (CRC or overflow) it replies with terminating retry ACK (Retry=1 and Nump == 0).

Enabling this Auto Retry feature in controller will make the core send a non-terminanting ACK upon such transaction errors. That is, ACK TP with Retry=1 and Nump != 0.

Doing so will give controller a chance to recover from transient error conditions.

Reference from below Linux commit,

commit <b138e23d3dff> ("usb: dwc3: core: Enable AutoRetry feature in the controller")

---
 drivers/usb/dwc3/core.c | 9 +++++++++
 drivers/usb/dwc3/core.h | 3 +++
 2 files changed, 12 insertions(+)
drivers/usb/dwc3/core.c +9 -0
index dc92f471c1..aab6c34c2d 100644
@@ -995,6 +995,15 @@ int dwc3_init(struct dwc3 *dwc)
 		dwc3_writel(dwc->regs, DWC3_GUCTL1, reg);
 	}
 
+	if (dwc->dr_mode == USB_DR_MODE_HOST ||
+	    dwc->dr_mode == USB_DR_MODE_OTG) {
+		reg = dwc3_readl(dwc->regs, DWC3_GUCTL);
+
+		reg |= DWC3_GUCTL_HSTINAUTORETRY;
+
+		dwc3_writel(dwc->regs, DWC3_GUCTL, reg);
+	}
+
 	ret = dwc3_core_init_mode(dwc);
 	if (ret)
 		goto mode_fail;
drivers/usb/dwc3/core.h +3 -0
index b510d8a983..2adcaf0029 100644
@@ -160,6 +160,9 @@
 #define DWC3_GCTL_GBLHIBERNATIONEN	(1 << 1)
 #define DWC3_GCTL_DSBLCLKGTNG		(1 << 0)
 
+/* Global User Control Register */
+#define DWC3_GUCTL_HSTINAUTORETRY	BIT(14)
+
 /* Global User Control 1 Register */
 #define DWC3_GUCTL1_TX_IPGAP_LINECHECK_DIS	BIT(28)
 #define DWC3_GUCTL1_DEV_L1_EXIT_BY_HW	BIT(24)
Signature · 1 line
2.17.1

A message that is not in the archive (sent off-list or not yet received): 20200526033435.20235-1-frank.wang-TNX95d0MmH7DzftRWevZcw@public.gmane.org

author
#16 lore raw

PATCH v6 11/16 usb: dwc3: amend UTMI/UTMIW phy interface setup

Let move 8/16-bit UTMI+ interface initialization into DWC3 core init that is convenient for both DM_USB and u-boot traditional process.

---
 drivers/usb/common/common.c | 25 ++++++++++++++
 drivers/usb/dwc3/core.c     | 65 +++++++++++++++++++------------------
 drivers/usb/dwc3/core.h     |  5 +++
 include/linux/usb/phy.h     | 18 ++++++++++
 4 files changed, 82 insertions(+), 31 deletions(-)
drivers/usb/common/common.c +25 -0
index 0db281b970..d4ae18693c 100644
@@ -10,6 +10,7 @@
 #include <dm.h>
 #include <linux/usb/otg.h>
 #include <linux/usb/ch9.h>
+#include <linux/usb/phy.h>
 
 DECLARE_GLOBAL_DATA_PTR;
 
@@ -64,3 +65,27 @@ enum usb_device_speed usb_get_maximum_speed(ofnode node)
 
 	return USB_SPEED_UNKNOWN;
 }
+
+#if CONFIG_IS_ENABLED(DM_USB)
+static const char *const usbphy_modes[] = {
+	[USBPHY_INTERFACE_MODE_UNKNOWN]	= "",
+	[USBPHY_INTERFACE_MODE_UTMI]	= "utmi",
+	[USBPHY_INTERFACE_MODE_UTMIW]	= "utmi_wide",
+};
+
+enum usb_phy_interface usb_get_phy_mode(ofnode node)
+{
+	const char *phy_type;
+	int i;
+
+	phy_type = ofnode_get_property(node, "phy_type", NULL);
+	if (!phy_type)
+		return USBPHY_INTERFACE_MODE_UNKNOWN;
+
+	for (i = 0; i < ARRAY_SIZE(usbphy_modes); i++)
+		if (!strcmp(phy_type, usbphy_modes[i]))
+			return i;
+
+	return USBPHY_INTERFACE_MODE_UNKNOWN;
+}
+#endif
drivers/usb/dwc3/core.c +34 -31

101 lines not on this page · raw message

drivers/usb/dwc3/core.h +5 -0
index 2adcaf0029..8e562ae6c4 100644
@@ -21,6 +21,7 @@
 
 #include <linux/usb/ch9.h>
 #include <linux/usb/otg.h>
+#include <linux/usb/phy.h>
 
 #define DWC3_MSG_MAX	500
 
@@ -658,6 +659,9 @@ struct dwc3_scratchpad_array {
  * @maximum_speed: maximum speed requested (mainly for testing purposes)
  * @revision: revision register contents
  * @dr_mode: requested mode of operation
+ * @hsphy_mode: UTMI phy mode, one of following:
+ *		- USBPHY_INTERFACE_MODE_UTMI
+ *		- USBPHY_INTERFACE_MODE_UTMIW
  * @dcfg: saved contents of DCFG register
  * @gctl: saved contents of GCTL register
  * @isoch_delay: wValue from Set Isochronous Delay request;
@@ -749,6 +753,7 @@ struct dwc3 {
 	size_t			regs_size;
 
 	enum usb_dr_mode	dr_mode;
+	enum usb_phy_interface	hsphy_mode;
 
 	/* used for suspend/resume */
 	u32			dcfg;
include/linux/usb/phy.h +18 -0
index 158ca9cd85..1e1217a958 100644
@@ -10,10 +10,28 @@
 #ifndef __LINUX_USB_PHY_H
 #define __LINUX_USB_PHY_H
 
+#include <dm/ofnode.h>
+
 enum usb_phy_interface {
 	USBPHY_INTERFACE_MODE_UNKNOWN,
 	USBPHY_INTERFACE_MODE_UTMI,
 	USBPHY_INTERFACE_MODE_UTMIW,
 };
 
+#if CONFIG_IS_ENABLED(DM_USB)
+/**
+ * usb_get_phy_mode - Get phy mode for given device_node
+ * @np:	Pointer to the given device_node
+ *
+ * The function gets phy interface string from property 'phy_type',
+ * and returns the corresponding enum usb_phy_interface
+ */
+enum usb_phy_interface usb_get_phy_mode(ofnode node);
+#else
+static inline enum usb_phy_interface usb_get_phy_mode(ofnode node)
+{
+	return USBPHY_INTERFACE_MODE_UNKNOWN;
+}
+#endif
+
 #endif /* __LINUX_USB_PHY_H */
Signature · 1 line
2.17.1
author
#17 lore raw

PATCH v6 12/16 usb: dwc3: add make compatible for rockchip platform

In reply to a message not in the archive

RK3399 Type-C PHY is required that must hold whole USB3.0 OTG controller in resetting to hold pipe power state in P2 before initializing the PHY. This commit fixed it and added device compatible for rockchip platform.

---
 drivers/usb/dwc3/dwc3-generic.c | 33 +++++++++++++++++++++++++++------
 1 file changed, 27 insertions(+), 6 deletions(-)
drivers/usb/dwc3/dwc3-generic.c +27 -6
index eabd53a36d..421e0be135 100644
@@ -24,6 +24,12 @@
 #include <clk.h>
 #include <usb/xhci.h>
 
+struct dwc3_glue_data {
+	struct clk_bulk		clks;
+	struct reset_ctl_bulk	resets;
+	fdt_addr_t regs;
+};
+
 struct dwc3_generic_plat {
 	fdt_addr_t base;
 	u32 maximum_speed;
@@ -47,6 +53,7 @@ static int dwc3_generic_probe(struct udevice *dev,
 	int rc;
 	struct dwc3_generic_plat *plat = dev_get_platdata(dev);
 	struct dwc3 *dwc3 = &priv->dwc3;
+	struct dwc3_glue_data *glue = dev_get_platdata(dev->parent);
 
 	dwc3->dev = dev;
 	dwc3->maximum_speed = plat->maximum_speed;
@@ -55,10 +62,22 @@ static int dwc3_generic_probe(struct udevice *dev,
 	dwc3_of_parse(dwc3);
 #endif
 
+	/*
+	 * It must hold whole USB3.0 OTG controller in resetting to hold pipe
+	 * power state in P2 before initializing TypeC PHY on RK3399 platform.
+	 */
+	if (device_is_compatible(dev->parent, "rockchip,rk3399-dwc3")) {
+		reset_assert_bulk(&glue->resets);
+		udelay(1);
+	}
+
 	rc = dwc3_setup_phy(dev, &priv->phys);
 	if (rc)
 		return rc;
 
+	if (device_is_compatible(dev->parent, "rockchip,rk3399-dwc3"))
+		reset_deassert_bulk(&glue->resets);
+
 	priv->base = map_physmem(plat->base, DWC3_OTG_REGS_END, MAP_NOCACHE);
 	dwc3->regs = priv->base + DWC3_GLOBALS_REGS_START;
 
@@ -186,12 +205,6 @@ U_BOOT_DRIVER(dwc3_generic_host) = {
 };
 #endif
 
-struct dwc3_glue_data {
-	struct clk_bulk		clks;
-	struct reset_ctl_bulk	resets;
-	fdt_addr_t regs;
-};
-
 struct dwc3_glue_ops {
 	void (*select_dr_mode)(struct udevice *dev, int index,
 			       enum usb_dr_mode mode);
@@ -394,6 +407,12 @@ static int dwc3_glue_probe(struct udevice *dev)
 	if (ret)
 		return ret;
 
+	if (glue->resets.count == 0) {
+		ret = dwc3_glue_reset_init(child, glue);
+		if (ret)
+			return ret;
+	}
+
 	while (child) {
 		enum usb_dr_mode dr_mode;
 
@@ -424,6 +443,8 @@ static const struct udevice_id dwc3_glue_ids[] = {
 	{ .compatible = "ti,dwc3", .data = (ulong)&ti_ops },
 	{ .compatible = "ti,am437x-dwc3", .data = (ulong)&ti_ops },
 	{ .compatible = "ti,am654-dwc3" },
+	{ .compatible = "rockchip,rk3328-dwc3" },
+	{ .compatible = "rockchip,rk3399-dwc3" },
 	{ }
 };
 
Signature · 1 line
2.17.1
#18 lore raw

Re: [PATCH v6 12/16] usb: dwc3: add make compatible for rockchip platform

Quoted 38 lines · Frank Wang

RK3399 Type-C PHY is required that must hold whole USB3.0 OTG controller in resetting to hold pipe power state in P2 before initializing the PHY. This commit fixed it and added device compatible for rockchip platform.

---
 drivers/usb/dwc3/dwc3-generic.c | 33 +++++++++++++++++++++++++++------
 1 file changed, 27 insertions(+), 6 deletions(-)
drivers/usb/dwc3/dwc3-generic.c +7 -0
index eabd53a36d..421e0be135 100644
@@ -24,6 +24,12 @@
 #include <clk.h>
 #include <usb/xhci.h>
 
+struct dwc3_glue_data {
+       struct clk_bulk         clks;
+       struct reset_ctl_bulk   resets;
+       fdt_addr_t regs;
+};
+
 struct dwc3_generic_plat {
        fdt_addr_t base;
        u32 maximum_speed;
@@ -47,6 +53,7 @@ static int dwc3_generic_probe(struct udevice *dev,
        int rc;
        struct dwc3_generic_plat *plat = dev_get_platdata(dev);
        struct dwc3 *dwc3 = &priv->dwc3;
+       struct dwc3_glue_data *glue = dev_get_platdata(dev->parent);
 
        dwc3->dev = dev;
        dwc3->maximum_speed = plat->maximum_speed;

drivers/usb/dwc3/dwc3-generic.c static int dwc3_generic_probe(struct udevice *dev, · line 71

Quoted 10 lines
drivers/usb/dwc3/dwc3-generic.c +7 -0
@@ -55,10 +62,22 @@ static int dwc3_generic_probe(struct udevice *dev,
        dwc3_of_parse(dwc3);
 #endif
 
+       /*
+        * It must hold whole USB3.0 OTG controller in resetting to hold pipe
+        * power state in P2 before initializing TypeC PHY on RK3399 platform.
+        */
+       if (device_is_compatible(dev->parent, "rockchip,rk3399-dwc3")) {
+               reset_assert_bulk(&glue->resets);
+               udelay(1);

Need to include <linux/delay.h> to fix build warnings, maybe Kever will do while applying?

Jagan.

author
#19 lore raw

PATCH v6 13/16 driver: usb: drop legacy rockchip xhci driver

In reply to a message not in the archive

We have changed to use dwc3 generic driver for usb3.0 host, so the legacy Rockchip's xHCI driver is not needed, and drop it.

---
 drivers/usb/host/Kconfig         |   9 --
 drivers/usb/host/Makefile        |   1 -
 drivers/usb/host/xhci-rockchip.c | 196 -------------------------------
 3 files changed, 206 deletions(-)
 delete mode 100644 drivers/usb/host/xhci-rockchip.c
drivers/usb/host/Kconfig +0 -9
index 2f381dc958..088931a6b9 100644
@@ -53,15 +53,6 @@ config USB_XHCI_PCI
 	help
 	  Enables support for the PCI-based xHCI controller.
 
-config USB_XHCI_ROCKCHIP
-	bool "Support for Rockchip on-chip xHCI USB controller"
-	depends on ARCH_ROCKCHIP
-	depends on DM_REGULATOR
-	depends on DM_USB
-	default y
-	help
-	  Enables support for the on-chip xHCI controller on Rockchip SoCs.
-
 config USB_XHCI_RCAR
 	bool "Renesas RCar USB 3.0 support"
 	default y
drivers/usb/host/Makefile +0 -1
index e8e3b17e42..29d4f87e38 100644
@@ -48,7 +48,6 @@ obj-$(CONFIG_USB_XHCI_BRCM) += xhci-brcm.o
 obj-$(CONFIG_USB_XHCI_HCD) += xhci.o xhci-mem.o xhci-ring.o
 obj-$(CONFIG_USB_XHCI_DWC3) += xhci-dwc3.o
 obj-$(CONFIG_USB_XHCI_DWC3_OF_SIMPLE) += dwc3-of-simple.o
-obj-$(CONFIG_USB_XHCI_ROCKCHIP) += xhci-rockchip.o
 obj-$(CONFIG_USB_XHCI_EXYNOS) += xhci-exynos5.o
 obj-$(CONFIG_USB_XHCI_FSL) += xhci-fsl.o
 obj-$(CONFIG_USB_XHCI_MTK) += xhci-mtk.o
drivers/usb/host/xhci-rockchip.c deleted +0 -196

196 lines not on this page · raw message

Signature · 1 line
2.17.1
maintainer
#20 lore raw

Re: [PATCH v6 13/16] driver: usb: drop legacy rockchip xhci driver

Am Dienstag, 26. Mai 2020, 05:34:32 CEST schrieb Frank Wang:

Quoted 6 lines

We have changed to use dwc3 generic driver for usb3.0 host, so the legacy Rockchip's xHCI driver is not needed, and drop it.

this needs to be adapted for
commit f7ae49fc4f36 ("common: Drop log.h from common header") which added a

	#include <log.h>

to xhci-rockchip.c

Heiko

author
#21 lore raw

PATCH v6 14/16 ARM: dts: rk3399-evb: usb3.0 host support

In reply to a message not in the archive

Configure 'tcphy1' and 'usbdrd_dwc3_1' nodes to support USB3.0 host for Rockchip RK3399 Evaluation Board.

---
 arch/arm/dts/rk3399-evb-u-boot.dtsi | 13 +++++++++++++
 1 file changed, 13 insertions(+)
arch/arm/dts/rk3399-evb-u-boot.dtsi +13 -0
index e5659d7999..1bebe258f0 100644
@@ -23,3 +23,16 @@
 &rk808 {
 	u-boot,dm-pre-reloc;
 };
+
+&tcphy1 {
+	status = "okay";
+};
+
+&usbdrd3_1 {
+	status = "okay";
+};
+
+&usbdrd_dwc3_1 {
+	dr_mode = "host";
+	status = "okay";
+};
Signature · 1 line
2.17.1
author
#22 lore raw

PATCH v6 15/16 configs: evb-rk3399: update support usb3.0 host

In reply to a message not in the archive

Update evb-rk3399 default config to support USB3.0 Host.

---
 configs/evb-rk3399_defconfig | 6 ++++++
 1 file changed, 6 insertions(+)
configs/evb-rk3399_defconfig +6 -0
index 7f14e18b1b..6cfb4e5dac 100644
@@ -28,6 +28,7 @@ CONFIG_SYS_RELOC_GD_ENV_ADDR=y
 CONFIG_NET_RANDOM_ETHADDR=y
 CONFIG_ROCKCHIP_GPIO=y
 CONFIG_SYS_I2C_ROCKCHIP=y
+CONFIG_MISC=y
 CONFIG_MMC_DW=y
 CONFIG_MMC_SDHCI=y
 CONFIG_MMC_SDHCI_ROCKCHIP=y
@@ -35,10 +36,13 @@ CONFIG_SF_DEFAULT_SPEED=20000000
 CONFIG_DM_ETH=y
 CONFIG_ETH_DESIGNWARE=y
 CONFIG_GMAC_ROCKCHIP=y
+CONFIG_PHY_ROCKCHIP_INNO_USB2=y
+CONFIG_PHY_ROCKCHIP_TYPEC=y
 CONFIG_PMIC_RK8XX=y
 CONFIG_REGULATOR_PWM=y
 CONFIG_REGULATOR_RK8XX=y
 CONFIG_PWM_ROCKCHIP=y
+CONFIG_DM_RESET=y
 CONFIG_DM_RNG=y
 CONFIG_RNG_ROCKCHIP=y
 CONFIG_BAUDRATE=1500000
@@ -49,6 +53,8 @@ CONFIG_USB_XHCI_HCD=y
 CONFIG_USB_XHCI_DWC3=y
 CONFIG_USB_EHCI_HCD=y
 CONFIG_USB_EHCI_GENERIC=y
+CONFIG_USB_DWC3=y
+CONFIG_USB_DWC3_GENERIC=y
 CONFIG_USB_HOST_ETHER=y
 CONFIG_USB_ETHER_ASIX=y
 CONFIG_USB_ETHER_ASIX88179=y
Signature · 1 line
2.17.1

A message that is not in the archive (sent off-list or not yet received): 20200526033516.20325-1-frank.wang-TNX95d0MmH7DzftRWevZcw@public.gmane.org

author
#24 lore raw

PATCH v6 16/16 roc-rk3399-pc: Enable USB3.0 Host

From: Jagan Teki <jagan-dyjBcgdgk7Pe9wHmmfpqLFaTQe2KTcn/@public.gmane.org>

Enable USB3.0 Host support for ROC-RK3399-PC boards.

Tested USB3.0 SSD on Type C1 port on board.

=> usb start
starting USB...
Bus usb@fe380000: USB EHCI 1.00
Bus usb@fe3c0000: USB EHCI 1.00
Bus dwc3: usb maximum-speed not found
Register 2000140 NbrPorts 2
Starting the controller
USB XHCI 1.10
scanning bus usb@fe380000 for devices... 1 USB Device(s) found scanning bus usb@fe3c0000 for devices... 2 USB Device(s) found scanning bus dwc3 for devices... 6 USB Device(s) found
scanning usb for storage devices... 1 Storage Device(s) found
=> usb tree
USB device tree:
1 Hub (480 Mb/s, 0mA)
u-boot EHCI Host Controller

1 Hub (480 Mb/s, 0mA)
| u-boot EHCI Host Controller
|
+-2 Hub (480 Mb/s, 100mA)

        USB 2.0 Hub [MTT]

1 Hub (5 Gb/s, 0mA)
| U-Boot XHCI Host Controller
|

  +-2  Hub (480 Mb/s, 0mA)
  | |  VIA Labs, Inc. USB2.0 Hub
  | |
  | +-4  Hub (480 Mb/s, 100mA)
  |   |   USB 2.0 Hub
  |   |
  |   +-5   (480 Mb/s, 100mA)
  |        VIA Technologies Inc. USB 2.0 BILLBOARD  0000000000000001
  |
  +-3  Hub (5 Gb/s, 0mA)
    |  VIA Labs, Inc. USB3.0 Hub
    |
    +-6  Mass Storage (5 Gb/s, 224mA)
         JMicron External Disk 3.0 DB12345678A2

=> usb reset
resetting USB...
Bus usb@fe380000: USB EHCI 1.00
Bus usb@fe3c0000: USB EHCI 1.00
Bus dwc3: usb maximum-speed not found
Register 2000140 NbrPorts 2
Starting the controller
USB XHCI 1.10
scanning bus usb@fe380000 for devices... 1 USB Device(s) found scanning bus usb@fe3c0000 for devices... 2 USB Device(s) found scanning bus dwc3 for devices... 6 USB Device(s) found
scanning usb for storage devices... 1 Storage Device(s) found

---
 configs/roc-pc-mezzanine-rk3399_defconfig | 5 +++++
 configs/roc-pc-rk3399_defconfig           | 6 ++++++
 2 files changed, 11 insertions(+)
configs/roc-pc-mezzanine-rk3399_defconfig +5 -0
index 0b853805f3..1f10856caa 100644
@@ -29,6 +29,7 @@ CONFIG_ENV_IS_IN_MMC=y
 CONFIG_SYS_RELOC_GD_ENV_ADDR=y
 CONFIG_ROCKCHIP_GPIO=y
 CONFIG_SYS_I2C_ROCKCHIP=y
+CONFIG_MISC=y
 CONFIG_MMC_DW=y
 CONFIG_MMC_DW_ROCKCHIP=y
 CONFIG_MMC_SDHCI=y
@@ -39,6 +40,8 @@ CONFIG_ETH_DESIGNWARE=y
 CONFIG_GMAC_ROCKCHIP=y
 CONFIG_NVME=y
 CONFIG_PCI=y
+CONFIG_PHY_ROCKCHIP_INNO_USB2=y
+CONFIG_PHY_ROCKCHIP_TYPEC=y
 CONFIG_PMIC_RK8XX=y
 CONFIG_REGULATOR_PWM=y
 CONFIG_REGULATOR_RK8XX=y
@@ -54,6 +57,8 @@ CONFIG_USB_XHCI_HCD=y
 CONFIG_USB_XHCI_DWC3=y
 CONFIG_USB_EHCI_HCD=y
 CONFIG_USB_EHCI_GENERIC=y
+CONFIG_USB_DWC3=y
+CONFIG_USB_DWC3_GENERIC=y
 CONFIG_USB_HOST_ETHER=y
 CONFIG_USB_ETHER_ASIX=y
 CONFIG_USB_ETHER_ASIX88179=y
configs/roc-pc-rk3399_defconfig +6 -0
index aff690f039..76e76c160e 100644
@@ -28,6 +28,7 @@ CONFIG_ENV_IS_IN_MMC=y
 CONFIG_SYS_RELOC_GD_ENV_ADDR=y
 CONFIG_ROCKCHIP_GPIO=y
 CONFIG_SYS_I2C_ROCKCHIP=y
+CONFIG_MISC=y
 CONFIG_MMC_DW=y
 CONFIG_MMC_DW_ROCKCHIP=y
 CONFIG_MMC_SDHCI=y
@@ -36,11 +37,14 @@ CONFIG_SPI_FLASH_WINBOND=y
 CONFIG_DM_ETH=y
 CONFIG_ETH_DESIGNWARE=y
 CONFIG_GMAC_ROCKCHIP=y
+CONFIG_PHY_ROCKCHIP_INNO_USB2=y
+CONFIG_PHY_ROCKCHIP_TYPEC=y
 CONFIG_PMIC_RK8XX=y
 CONFIG_REGULATOR_PWM=y
 CONFIG_REGULATOR_RK8XX=y
 CONFIG_PWM_ROCKCHIP=y
 CONFIG_RAM_RK3399_LPDDR4=y
+CONFIG_DM_RESET=y
 CONFIG_BAUDRATE=1500000
 CONFIG_DEBUG_UART_SHIFT=2
 CONFIG_ROCKCHIP_SPI=y
@@ -50,6 +54,8 @@ CONFIG_USB_XHCI_HCD=y
 CONFIG_USB_XHCI_DWC3=y
 CONFIG_USB_EHCI_HCD=y
 CONFIG_USB_EHCI_GENERIC=y
+CONFIG_USB_DWC3=y
+CONFIG_USB_DWC3_GENERIC=y
 CONFIG_USB_KEYBOARD=y
 CONFIG_USB_HOST_ETHER=y
 CONFIG_USB_ETHER_ASIX=y
Signature · 1 line
2.17.1
#25 lore raw
In reply to a message not in the archive
Quoted 77 lines · Frank Wang

This series add quirks for DWC3 and add Rockchip RK3399 USB3.0 host support.

The function has been tested pass on rk3399-evb and roc-rk3399-pc board.

For V6 update:
- Use [PATCH v6 04/16] instead of [PATCH v5 05/16] to fix that the current Generic PHY subsystem is unable to find PHY if the PHY node is not part of the root structure.
- Add 'Reviewed-by' tag for all patches except [PATCH v6 04/16].

For V5 update:
- Fix dwc3-generic driver followed Marek's comments for [PATCH v4 12/16].
- Add 'Reviewed-by' and 'Tested-by' tag for [PATCH v4 07/16] and [PATCH v4 08/16].

For V4 update:
- Collect Jagan's all fixed patches [1].
- Amend specific u-boot changes from dts to dtsi for [PATCH v3 6/7].

For V3 update:
- Fix compile error for [PATCH v2 1/9].
- Use Jagan's Type-C driver instead of [PATCH v2 5/9].
- Cleanup dts changes for [PATCH v2 7/9].
- Cleanup config changes for [PATCH v2 8/9] and [PATCH v2 9/9].

For V2 update:
- Amend type-c driver followed Jagan's comments for [PATCH 5/8].
- Fix dts commit for [PATCH 7/8].
- Split RK3399 default config for [PATCH 8/8].
- Add 'Reviewed-by' tag for [PATCH 1/8], [PATCH 2/8] and [PATCH 3/8].

[1] https://patchwork.ozlabs.org/project/uboot/cover/[email protected]

BR,
Frank

Frank Wang (8):
arm: mach-rockchip: bind sub-nodes for rk3399_syscon
usb: dwc3: add dis_enblslpm_quirk
usb: dwc3: add dis_u2_freeclk_exists_quirk
usb: dwc3: amend UTMI/UTMIW phy interface setup
usb: dwc3: add make compatible for rockchip platform
driver: usb: drop legacy rockchip xhci driver
ARM: dts: rk3399-evb: usb3.0 host support
configs: evb-rk3399: update support usb3.0 host

Jagan Teki (8):
clk: rk3399: Enable/Disable the USB2PHY clk
clk: rk3399: Set empty for TCPHY assigned-clocks
clk: rk3399: Enable/Disable TCPHY clocks
phy: rockchip: Add Rockchip USB2PHY driver
phy: rockchip: Add Rockchip USB TypeC PHY driver
usb: dwc3: Add disable u2mac linestate check quirk
usb: dwc3: Enable AutoRetry feature in the controller
roc-rk3399-pc: Enable USB3.0 Host

  arch/arm/dts/rk3399-evb-u-boot.dtsi           |  13 +
  arch/arm/mach-rockchip/rk3399/syscon_rk3399.c |   3 +
  configs/evb-rk3399_defconfig                  |   6 +
  configs/roc-pc-mezzanine-rk3399_defconfig     |   5 +
  configs/roc-pc-rk3399_defconfig               |   6 +
  drivers/Makefile                              |   1 +
  drivers/clk/rockchip/clk_rk3399.c             |  38 +
  drivers/phy/Kconfig                           |   1 +
  drivers/phy/rockchip/Kconfig                  |  21 +
  drivers/phy/rockchip/Makefile                 |   7 +
  drivers/phy/rockchip/phy-rockchip-inno-usb2.c | 312 +++++++
  drivers/phy/rockchip/phy-rockchip-typec.c     | 796 ++++++++++++++++++
  drivers/usb/common/common.c                   |  25 +
  drivers/usb/dwc3/core.c                       | 106 ++-
  drivers/usb/dwc3/core.h                       |  19 +
  drivers/usb/dwc3/dwc3-generic.c               |  33 +-
  drivers/usb/host/Kconfig                      |   9 -
  drivers/usb/host/Makefile                     |   1 -
  drivers/usb/host/xhci-rockchip.c              | 196 -----
  include/dwc3-uboot.h                          |   3 +
  include/linux/usb/phy.h                       |  18 +
  21 files changed, 1376 insertions(+), 243 deletions(-)
Quoted 6 lines

create mode 100644 drivers/phy/rockchip/Kconfig create mode 100644 drivers/phy/rockchip/Makefile create mode 100644 drivers/phy/rockchip/phy-rockchip-inno-usb2.c create mode 100644 drivers/phy/rockchip/phy-rockchip-typec.c delete mode 100644 drivers/usb/host/xhci-rockchip.c

Applied to u-boot-rockchip master.

Thanks,
- Kever

_______________________________________________
Linux-rockchip mailing list
[email protected]
http://lists.infradead.org/mailman/listinfo/linux-rockchip

#26 lore raw
In reply to Frank Wang
Quoted 36 lines · Frank Wang

This series add quirks for DWC3 and add Rockchip RK3399 USB3.0 host support.

The function has been tested pass on rk3399-evb and roc-rk3399-pc board.

For V6 update:
- Use [PATCH v6 04/16] instead of [PATCH v5 05/16] to fix that the current Generic PHY subsystem is unable to find PHY if the PHY node is not part of the root structure.
- Add 'Reviewed-by' tag for all patches except [PATCH v6 04/16].

For V5 update:
- Fix dwc3-generic driver followed Marek's comments for [PATCH v4 12/16].
- Add 'Reviewed-by' and 'Tested-by' tag for [PATCH v4 07/16] and [PATCH v4 08/16].

For V4 update:
- Collect Jagan's all fixed patches [1].
- Amend specific u-boot changes from dts to dtsi for [PATCH v3 6/7].

For V3 update:
- Fix compile error for [PATCH v2 1/9].
- Use Jagan's Type-C driver instead of [PATCH v2 5/9].
- Cleanup dts changes for [PATCH v2 7/9].
- Cleanup config changes for [PATCH v2 8/9] and [PATCH v2 9/9].

For V2 update:
- Amend type-c driver followed Jagan's comments for [PATCH 5/8].
- Fix dts commit for [PATCH 7/8].
- Split RK3399 default config for [PATCH 8/8].
- Add 'Reviewed-by' tag for [PATCH 1/8], [PATCH 2/8] and [PATCH 3/8].

[1] https://patchwork.ozlabs.org/project/uboot/cover/[email protected]

BR,
Frank

Quoted 9 lines

Frank Wang (8):
arm: mach-rockchip: bind sub-nodes for rk3399_syscon
usb: dwc3: add dis_enblslpm_quirk
usb: dwc3: add dis_u2_freeclk_exists_quirk
usb: dwc3: amend UTMI/UTMIW phy interface setup
usb: dwc3: add make compatible for rockchip platform
driver: usb: drop legacy rockchip xhci driver
ARM: dts: rk3399-evb: usb3.0 host support
configs: evb-rk3399: update support usb3.0 host

I have a new sandisk Type C and A storage disk. Here are the tests in roc-rk3399-pc.

=> usb tree
USB device tree:
1 Hub (480 Mb/s, 0mA)
u-boot EHCI Host Controller

1 Hub (480 Mb/s, 0mA)
| u-boot EHCI Host Controller
|
+-2 Hub (480 Mb/s, 100mA)

        USB 2.0 Hub [MTT]

1 Hub (5 Gb/s, 0mA)
U-Boot XHCI Host Controller

=> usb reset
resetting USB...
Bus usb@fe380000: USB EHCI 1.00
Bus usb@fe3c0000: USB EHCI 1.00
Bus dwc3: usb maximum-speed not found
Register 2000140 NbrPorts 2
Starting the controller
USB XHCI 1.10
scanning bus usb@fe380000 for devices... 1 USB Device(s) found scanning bus usb@fe3c0000 for devices... 2 USB Device(s) found scanning bus dwc3 for devices... cannot reset port 1!?
2 USB Device(s) found
scanning usb for storage devices... 1 Storage Device(s) found
=> usb tree
USB device tree:
1 Hub (480 Mb/s, 0mA)
u-boot EHCI Host Controller

1 Hub (480 Mb/s, 0mA)
| u-boot EHCI Host Controller
|
+-2 Hub (480 Mb/s, 100mA)

        USB 2.0 Hub [MTT]

1 Hub (5 Gb/s, 0mA)
| U-Boot XHCI Host Controller
|
+-2 Mass Storage (5 Gb/s, 224mA)

       SanDisk Dual Drive 040130e3ee554b7078843f4eb331646

=> usb reset
resetting USB...
Bus usb@fe380000: USB EHCI 1.00
Bus usb@fe3c0000: USB EHCI 1.00
Bus dwc3: usb maximum-speed not found
Register 2000140 NbrPorts 2
Starting the controller
USB XHCI 1.10
scanning bus usb@fe380000 for devices... 2 USB Device(s) found scanning bus usb@fe3c0000 for devices... 2 USB Device(s) found scanning bus dwc3 for devices... 1 USB Device(s) found
scanning usb for storage devices... 1 Storage Device(s) found
=> usb tree
USB device tree:
1 Hub (480 Mb/s, 0mA)
| u-boot EHCI Host Controller
|
+-2 Mass Storage (480 Mb/s, 224mA)

       SanDisk Dual Drive 040130e3ee554b7078843f4eb331646

1 Hub (480 Mb/s, 0mA)
| u-boot EHCI Host Controller
|
+-2 Hub (480 Mb/s, 100mA)

        USB 2.0 Hub [MTT]

1 Hub (5 Gb/s, 0mA)
U-Boot XHCI Host Controller

=> usb reset
resetting USB...
Bus usb@fe380000: USB EHCI 1.00
Bus usb@fe3c0000: USB EHCI 1.00
Bus dwc3: usb maximum-speed not found
Register 2000140 NbrPorts 2
Starting the controller
USB XHCI 1.10
scanning bus usb@fe380000 for devices... 1 USB Device(s) found scanning bus usb@fe3c0000 for devices... EHCI timed out on TD - token=0x80008d80

USB device not accepting new address (error=22)
2 USB Device(s) found
scanning bus dwc3 for devices... 1 USB Device(s) found
scanning usb for storage devices... 0 Storage Device(s) found
=>
resetting USB...
Bus usb@fe380000: USB EHCI 1.00
Bus usb@fe3c0000: USB EHCI 1.00
Bus dwc3: usb maximum-speed not found
Register 2000140 NbrPorts 2
Starting the controller
USB XHCI 1.10
scanning bus usb@fe380000 for devices... 1 USB Device(s) found scanning bus usb@fe3c0000 for devices... 3 USB Device(s) found scanning bus dwc3 for devices... 1 USB Device(s) found
scanning usb for storage devices... 1 Storage Device(s) found
=> usb tree
USB device tree:
1 Hub (480 Mb/s, 0mA)
u-boot EHCI Host Controller

1 Hub (480 Mb/s, 0mA)
| u-boot EHCI Host Controller
|

  +-2  Hub (480 Mb/s, 100mA)
    |   USB 2.0 Hub [MTT]
    |
    +-3  Mass Storage (480 Mb/s, 224mA)
         SanDisk Dual Drive 040130e3ee554b7078843f4eb331646

1 Hub (5 Gb/s, 0mA)
U-Boot XHCI Host Controller

=> usb reset
resetting USB...
Bus usb@fe380000: USB EHCI 1.00
Bus usb@fe3c0000: USB EHCI 1.00
Bus dwc3: usb maximum-speed not found
Register 2000140 NbrPorts 2
Starting the controller
USB XHCI 1.10
scanning bus usb@fe380000 for devices... 1 USB Device(s) found scanning bus usb@fe3c0000 for devices... EHCI timed out on TD - token=0x80008d80

USB device not accepting new address (error=22)
2 USB Device(s) found
scanning bus dwc3 for devices... 1 USB Device(s) found
scanning usb for storage devices... 0 Storage Device(s) found
=> usb reset
resetting USB...
Bus usb@fe380000: USB EHCI 1.00
Bus usb@fe3c0000: USB EHCI 1.00
Bus dwc3: usb maximum-speed not found
Register 2000140 NbrPorts 2
Starting the controller
USB XHCI 1.10
scanning bus usb@fe380000 for devices... 1 USB Device(s) found scanning bus usb@fe3c0000 for devices... 3 USB Device(s) found scanning bus dwc3 for devices... 1 USB Device(s) found
scanning usb for storage devices... 1 Storage Device(s) found
=> usb tree
USB device tree:
1 Hub (480 Mb/s, 0mA)
u-boot EHCI Host Controller

1 Hub (480 Mb/s, 0mA)
| u-boot EHCI Host Controller
|

  +-2  Hub (480 Mb/s, 100mA)
    |   USB 2.0 Hub [MTT]
    |
    +-3  Mass Storage (480 Mb/s, 224mA)
         SanDisk Dual Drive 040130e3ee554b7078843f4eb331646

1 Hub (5 Gb/s, 0mA)
U-Boot XHCI Host Controller

Jagan.

#27 lore raw

v6 cover Add Rockchip RK3399 USB3.0 Host support

In reply to Frank Wang

W dniu 26.05.2020 o 05:32, Frank Wang pisze:

Quoted 9 lines

This series add quirks for DWC3 and add Rockchip RK3399 USB3.0 host support.

The function has been tested pass on rk3399-evb and roc-rk3399-pc board.

For V6 update:
- Use [PATCH v6 04/16] instead of [PATCH v5 05/16] to fix that the current Generic PHY subsystem is unable to find PHY if the PHY node is not part of the root structure.
- Add 'Reviewed-by' tag for all patches except [PATCH v6 04/16].

On RockPro64 (config changes attached):

Model: Pine64 RockPro64 v2.1
Net:   eth0: ethernet at fe300000
Hit any key to stop autoboot:  0 

=> usb start;usb tree
starting USB...
Bus usb at fe380000: USB EHCI 1.00
Bus usb at fe3c0000: USB EHCI 1.00
Bus dwc3: usb maximum-speed not found
Register 2000140 NbrPorts 2
Starting the controller
USB XHCI 1.10
Bus dwc3: usb maximum-speed not found
Register 2000140 NbrPorts 2
Starting the controller
USB XHCI 1.10
scanning bus usb at fe380000 for devices... 1 USB Device(s) found scanning bus usb at fe3c0000 for devices... 1 USB Device(s) found scanning bus dwc3 for devices... 2 USB Device(s) found scanning bus dwc3 for devices... 1 USB Device(s) found
scanning usb for storage devices... 1 Storage Device(s) found
USB device tree:
1 Hub (480 Mb/s, 0mA)
u-boot EHCI Host Controller

1 Hub (480 Mb/s, 0mA)
u-boot EHCI Host Controller

1 Hub (5 Gb/s, 0mA)
| U-Boot XHCI Host Controller
|
+-2 Mass Storage (480 Mb/s, 224mA)

       SanDisk Ultra USB 3.0 4C530001300923104300

1 Hub (5 Gb/s, 0mA)
U-Boot XHCI Host Controller

Device is Sandisk C/A pendrive. Recognized as HighSpeed in USB-C port but as SuperSpeed in USB-A one:

=> usb reset;usb tree
resetting USB...
Bus usb at fe380000: USB EHCI 1.00
Bus usb at fe3c0000: USB EHCI 1.00
Bus dwc3: usb maximum-speed not found
Register 2000140 NbrPorts 2
Starting the controller
USB XHCI 1.10
Bus dwc3: usb maximum-speed not found
Register 2000140 NbrPorts 2
Starting the controller
USB XHCI 1.10
scanning bus usb at fe380000 for devices... 1 USB Device(s) found scanning bus usb at fe3c0000 for devices... 1 USB Device(s) found scanning bus dwc3 for devices... 1 USB Device(s) found scanning bus dwc3 for devices... cannot reset port 1!?
2 USB Device(s) found
scanning usb for storage devices... 1 Storage Device(s) found
USB device tree:
1 Hub (480 Mb/s, 0mA)
u-boot EHCI Host Controller

1 Hub (480 Mb/s, 0mA)
u-boot EHCI Host Controller

1 Hub (5 Gb/s, 0mA)
U-Boot XHCI Host Controller

1 Hub (5 Gb/s, 0mA)
| U-Boot XHCI Host Controller
|
+-2 Mass Storage (5 Gb/s, 224mA)

       SanDisk Ultra USB 3.0 4C530001300923104300

Whatever SuperSpeed device I plug into USB-C port it gets recognized as HighSpeed only.

"cannot reset port 1!?" message appears on almost (3/4) each 'usb start' and each 'usb reset' command.

Also checked one of those usb-c 2 usb-a/hdmi/usb-c-charge dongles and Sandisk was recognized as HighSpeed.
-------------- next part --------------
A non-text attachment was scrubbed...
Name: 0001-configs-rockpro64-rk3399-update-support-usb3.0-host.patch
Type: text/x-patch
Size: 1525 bytes
Desc: not available
URL: <https://lists.denx.de/pipermail/u-boot/attachments/20200526/d2cbb2a7/attachment.bin>