dt-bindings: power: Add BQ27561 compatible
Subsystems (4)
PATCH v2 1/4 dt-bindings: power: Add BQ27561 compatible
Add the Texas Instruments bq27561 battery monitor to the bq27xxx binding.
--- Documentation/devicetree/bindings/power/supply/bq27xxx.yaml | 1 + 1 file changed, 1 insertion(+)
Documentation/devicetree/bindings/power/supply/bq27xxx.yaml +1 -0
@@ -49,6 +49,7 @@ properties: - ti,bq27426 - ti,bq27441 - ti,bq27621 + - ti,bq27561 reg: maxItems: 1
Signature · 1 line
2.26.2
PATCH v2 2/4 power: supply: bq27xxx_battery: Add the BQ27561 Battery monitor
Add the Texas Instruments BQ27561 battery monitor. The register address map is laid out the same as compared to other devices within the file. The battery status register has differing bits to determine if the battery is full, discharging or dead.
--- drivers/power/supply/bq27xxx_battery.c | 68 +++++++++++++++++++++- drivers/power/supply/bq27xxx_battery_i2c.c | 2 + include/linux/power/bq27xxx_battery.h | 1 + 3 files changed, 70 insertions(+), 1 deletion(-)
drivers/power/supply/bq27xxx_battery.c +67 -1
@@ -43,6 +43,7 @@* http://www.ti.com/product/bq27411-g1 * http://www.ti.com/product/bq27441-g1 * http://www.ti.com/product/bq27621-g1 +* https://www.ti.com/lit/gpn/bq27z561 */ #include <linux/device.h>
@@ -79,6 +80,11 @@#define BQ27000_FLAG_FC BIT(5)#define BQ27000_FLAG_CHGS BIT(7)/* Charge state flag */ +/* BQ27561 has different layout for Flags register */ +#define BQ27561_FLAG_FDC BIT(4)/* Battery fully discharged */ +#define BQ27561_FLAG_FC BIT(5)/* Battery fully charged */ +#define BQ27561_FLAG_DIS_CH BIT(6)/* Battery is discharging */ +/* control register params */ #define BQ27XXX_SEALED 0x20#define BQ27XXX_SET_CFGUPDATE 0x13
@@ -431,12 +437,32 @@ static u8 [BQ27XXX_REG_DCAP] = 0x3c, [BQ27XXX_REG_AP ] =0x18 ,BQ27XXX_DM_REG_ROWS , - }; + }, #define bq27411_regs bq27421_regs #define bq27425_regs bq27421_regs #define bq27426_regs bq27421_regs #define bq27441_regs bq27421_regs #define bq27621_regs bq27421_regs + bq27561_regs[BQ27XXX_REG_MAX ] = { + [BQ27XXX_REG_CTRL ] =0x00 , + [BQ27XXX_REG_TEMP ] =0x06 , + [BQ27XXX_REG_INT_TEMP ] =INVALID_REG_ADDR , + [BQ27XXX_REG_VOLT ] =0x08 , + [BQ27XXX_REG_AI ] =0x14 , + [BQ27XXX_REG_FLAGS ] =0x0a , + [BQ27XXX_REG_TTE ] =0x16 , + [BQ27XXX_REG_TTF ] =0x18 , + [BQ27XXX_REG_TTES ] =INVALID_REG_ADDR , + [BQ27XXX_REG_TTECP ] =INVALID_REG_ADDR , + [BQ27XXX_REG_NAC ] =INVALID_REG_ADDR , + [BQ27XXX_REG_FCC ] =0x12 , + [BQ27XXX_REG_CYCT ] =0x2a , + [BQ27XXX_REG_AE ] =0x22 , + [BQ27XXX_REG_SOC ] =0x2c , + [BQ27XXX_REG_DCAP ] =0x3c , + [BQ27XXX_REG_AP ] =0x22 , +BQ27XXX_DM_REG_ROWS , + };static enum power_supply_property bq27000_props[] = {POWER_SUPPLY_PROP_STATUS ,
@@ -672,6 +698,25 @@ static enum power_supply_property bq27421_props[] = {#define bq27441_props bq27421_props#define bq27621_props bq27421_props +static enum power_supply_property bq27561_props[] = { +POWER_SUPPLY_PROP_STATUS , +POWER_SUPPLY_PROP_PRESENT , +POWER_SUPPLY_PROP_VOLTAGE_NOW , +POWER_SUPPLY_PROP_CURRENT_NOW , +POWER_SUPPLY_PROP_CAPACITY , +POWER_SUPPLY_PROP_CAPACITY_LEVEL , +POWER_SUPPLY_PROP_TEMP , +POWER_SUPPLY_PROP_TIME_TO_EMPTY_NOW , +POWER_SUPPLY_PROP_TIME_TO_FULL_NOW , +POWER_SUPPLY_PROP_TECHNOLOGY , +POWER_SUPPLY_PROP_CHARGE_FULL , +POWER_SUPPLY_PROP_CHARGE_FULL_DESIGN , +POWER_SUPPLY_PROP_CYCLE_COUNT , +POWER_SUPPLY_PROP_POWER_AVG , +POWER_SUPPLY_PROP_HEALTH , +POWER_SUPPLY_PROP_MANUFACTURER , +}; +struct bq27xxx_dm_reg {u8 subclass_id;u8 offset;
@@ -767,11 +812,14 @@ static struct bq27xxx_dm_reg bq27621_dm_regs[] = {#define bq27621_dm_regs 0#endif +#define bq27561_dm_regs 0 +#define BQ27XXX_O_ZERO 0x00000001#define BQ27XXX_O_OTDC 0x00000002/* has OTC/OTD overtemperature flags */ #define BQ27XXX_O_UTOT 0x00000004/* has OT overtemperature flag */ #define BQ27XXX_O_CFGUP 0x00000008#define BQ27XXX_O_RAM 0x00000010 +#define BQ27561_O_BITS 0x00000020#define BQ27XXX_DATA (ref, key, opt) { \ .opts = (opt), \
@@ -816,6 +864,7 @@ static struct { [BQ27426] = BQ27XXX_DATA(bq27426, 0x80008000, BQ27XXX_O_UTOT | BQ27XXX_O_CFGUP | BQ27XXX_O_RAM), [BQ27441] = BQ27XXX_DATA(bq27441, 0x80008000, BQ27XXX_O_UTOT | BQ27XXX_O_CFGUP | BQ27XXX_O_RAM), [BQ27621] = BQ27XXX_DATA(bq27621, 0x80008000, BQ27XXX_O_UTOT | BQ27XXX_O_CFGUP | BQ27XXX_O_RAM), + [BQ27561] = BQ27XXX_DATA(bq27561, 0 , BQ27561_O_BITS), };static DEFINE_MUTEX (bq27xxx_list_lock);
@@ -1551,6 +1600,8 @@ static bool bq27xxx_battery_dead(struct bq27xxx_device_info *di, u16 flags) {if (di->opts &BQ27XXX_O_ZERO )return flags & (BQ27000_FLAG_EDV1 |BQ27000_FLAG_EDVF ); +else if (di->opts &BQ27561_O_BITS ) +return flags &BQ27561_FLAG_FDC ;else return flags & (BQ27XXX_FLAG_SOC1 |BQ27XXX_FLAG_SOCF ); }
@@ -1595,6 +1646,7 @@ void bq27xxx_battery_update(struct bq27xxx_device_info *di) cache.time_to_empty_avg =bq27xxx_battery_read_time (di,BQ27XXX_REG_TTECP );if (di->regs[BQ27XXX_REG_TTF ] !=INVALID_REG_ADDR ) cache.time_to_full =bq27xxx_battery_read_time (di,BQ27XXX_REG_TTF ); + cache.charge_full =bq27xxx_battery_read_fcc (di); cache.capacity =bq27xxx_battery_read_soc (di);if (di->regs[BQ27XXX_REG_AE ] !=INVALID_REG_ADDR )
@@ -1682,6 +1734,13 @@ static int bq27xxx_battery_status(struct bq27xxx_device_info *di, status =POWER_SUPPLY_STATUS_NOT_CHARGING ; else status =POWER_SUPPLY_STATUS_DISCHARGING ; + }else if (di->opts &BQ27561_O_BITS ) { +if (di->cache.flags &BQ27561_FLAG_FC ) + status =POWER_SUPPLY_STATUS_FULL ; +else if (di->cache.flags &BQ27561_FLAG_DIS_CH ) + status =POWER_SUPPLY_STATUS_DISCHARGING ; +else + status =POWER_SUPPLY_STATUS_CHARGING ; }else {if (di->cache.flags &BQ27XXX_FLAG_FC ) status =POWER_SUPPLY_STATUS_FULL ;
@@ -1710,6 +1769,13 @@ static int bq27xxx_battery_capacity_level(struct bq27xxx_device_info *di, level =POWER_SUPPLY_CAPACITY_LEVEL_CRITICAL ; else level =POWER_SUPPLY_CAPACITY_LEVEL_NORMAL ; + }else if (di->opts &BQ27561_O_BITS ) { +if (di->cache.flags &BQ27561_FLAG_FC ) + level =POWER_SUPPLY_CAPACITY_LEVEL_FULL ; +else if (di->cache.flags &BQ27561_FLAG_DIS_CH ) + level =POWER_SUPPLY_CAPACITY_LEVEL_CRITICAL ; +else + level =POWER_SUPPLY_CAPACITY_LEVEL_NORMAL ; }else {if (di->cache.flags &BQ27XXX_FLAG_FC ) level =POWER_SUPPLY_CAPACITY_LEVEL_FULL ;
drivers/power/supply/bq27xxx_battery_i2c.c +2 -0
@@ -253,6 +253,7 @@ static const struct i2c_device_id bq27xxx_i2c_id_table[] = { { "bq27426", BQ27426 }, { "bq27441", BQ27441 }, { "bq27621", BQ27621 }, + { "bq27561", BQ27561 }, {}, };MODULE_DEVICE_TABLE (i2c, bq27xxx_i2c_id_table);
@@ -286,6 +287,7 @@ static const struct of_device_id bq27xxx_battery_i2c_of_match_table[] = { { .compatible = "ti,bq27426" }, { .compatible = "ti,bq27441" }, { .compatible = "ti,bq27621" }, + { .compatible = "ti,bq27561" }, {}, };MODULE_DEVICE_TABLE (of, bq27xxx_battery_i2c_of_match_table);
include/linux/power/bq27xxx_battery.h +1 -0
@@ -30,6 +30,7 @@ enum bq27xxx_chip {BQ27426 ,BQ27441 ,BQ27621 , + BQ27561, };struct bq27xxx_device_info ;
Signature · 1 line
2.26.2
PATCH v2 3/4 dt-bindings: power: Add BQ28z610 compatible
In reply to Dan MurphyAdd the Texas Instruments bq28z610 battery monitor to the bq27xxx binding.
--- Documentation/devicetree/bindings/power/supply/bq27xxx.yaml | 1 + 1 file changed, 1 insertion(+)
Documentation/devicetree/bindings/power/supply/bq27xxx.yaml +1 -0
@@ -50,6 +50,7 @@ properties: - ti,bq27441 - ti,bq27621 - ti,bq27561 + - ti,bq28z610 reg: maxItems: 1
Signature · 1 line
2.26.2
Re: [PATCH v2 3/4] dt-bindings: power: Add BQ28z610 compatible
Quoted 8 lines · Dan Murphy
Add the Texas Instruments bq28z610 battery monitor to the bq27xxx binding.
Signed-off-by Dan Murphy <[email protected]>--- Documentation/devicetree/bindings/power/supply/bq27xxx.yaml | 1 + 1 file changed, 1 insertion(+)
PATCH v2 4/4 power: supply: bq27xxx_battery: Add the BQ28z610 Battery monitor
In reply to Dan MurphyAdd the Texas Instruments BQ28z610 battery monitor.
The register address map is laid out the same as compared to other devices within the file.
The battery status register bits are similar to the BQ27561 but they are different compared to other fuel gauge devices within this file.
--- drivers/power/supply/bq27xxx_battery.c | 42 ++++++++++++++++++++++ drivers/power/supply/bq27xxx_battery_i2c.c | 2 ++ include/linux/power/bq27xxx_battery.h | 1 + 3 files changed, 45 insertions(+)
drivers/power/supply/bq27xxx_battery.c +42 -0
@@ -44,6 +44,7 @@* http://www.ti.com/product/bq27441-g1 * http://www.ti.com/product/bq27621-g1 * https://www.ti.com/lit/gpn/bq27z561 +* https://www.ti.com/lit/gpn/bq28z610 */ #include <linux/device.h>
@@ -462,6 +463,26 @@ static u8 [BQ27XXX_REG_DCAP] = 0x3c, [BQ27XXX_REG_AP ] =0x22 ,BQ27XXX_DM_REG_ROWS , + }, + bq28z610_regs[BQ27XXX_REG_MAX ] = { + [BQ27XXX_REG_CTRL ] =0x00 , + [BQ27XXX_REG_TEMP ] =0x06 , + [BQ27XXX_REG_INT_TEMP ] =INVALID_REG_ADDR , + [BQ27XXX_REG_VOLT ] =0x08 , + [BQ27XXX_REG_AI ] =0x14 , + [BQ27XXX_REG_FLAGS ] =0x0a , + [BQ27XXX_REG_TTE ] =0x16 , + [BQ27XXX_REG_TTF ] =0x18 , + [BQ27XXX_REG_TTES ] =INVALID_REG_ADDR , + [BQ27XXX_REG_TTECP ] =INVALID_REG_ADDR , + [BQ27XXX_REG_NAC ] =INVALID_REG_ADDR , + [BQ27XXX_REG_FCC ] =0x12 , + [BQ27XXX_REG_CYCT ] =0x2a , + [BQ27XXX_REG_AE ] =0x22 , + [BQ27XXX_REG_SOC ] =0x2c , + [BQ27XXX_REG_DCAP ] =0x3c , + [BQ27XXX_REG_AP ] =0x22 , +BQ27XXX_DM_REG_ROWS , };static enum power_supply_property bq27000_props[] = {
@@ -717,6 +738,25 @@ static enum power_supply_property bq27561_props[] = { POWER_SUPPLY_PROP_MANUFACTURER, }; +static enum power_supply_property bq28z610_props[] = { +POWER_SUPPLY_PROP_STATUS , +POWER_SUPPLY_PROP_PRESENT , +POWER_SUPPLY_PROP_VOLTAGE_NOW , +POWER_SUPPLY_PROP_CURRENT_NOW , +POWER_SUPPLY_PROP_CAPACITY , +POWER_SUPPLY_PROP_CAPACITY_LEVEL , +POWER_SUPPLY_PROP_TEMP , +POWER_SUPPLY_PROP_TIME_TO_EMPTY_NOW , +POWER_SUPPLY_PROP_TIME_TO_FULL_NOW , +POWER_SUPPLY_PROP_TECHNOLOGY , +POWER_SUPPLY_PROP_CHARGE_FULL , +POWER_SUPPLY_PROP_CHARGE_FULL_DESIGN , +POWER_SUPPLY_PROP_CYCLE_COUNT , +POWER_SUPPLY_PROP_POWER_AVG , +POWER_SUPPLY_PROP_HEALTH , +POWER_SUPPLY_PROP_MANUFACTURER , +}; +struct bq27xxx_dm_reg {u8 subclass_id;u8 offset;
@@ -813,6 +853,7 @@ static struct bq27xxx_dm_reg bq27621_dm_regs[] = {#endif #define bq27561_dm_regs 0 +#define bq28z610_dm_regs 0#define BQ27XXX_O_ZERO 0x00000001#define BQ27XXX_O_OTDC 0x00000002/* has OTC/OTD overtemperature flags */
@@ -865,6 +906,7 @@ static struct { [BQ27441] = BQ27XXX_DATA(bq27441, 0x80008000, BQ27XXX_O_UTOT | BQ27XXX_O_CFGUP | BQ27XXX_O_RAM), [BQ27621] = BQ27XXX_DATA(bq27621, 0x80008000, BQ27XXX_O_UTOT | BQ27XXX_O_CFGUP | BQ27XXX_O_RAM), [BQ27561] = BQ27XXX_DATA(bq27561, 0 , BQ27561_O_BITS), + [BQ28Z610] = BQ27XXX_DATA(bq28z610, 0 , BQ27561_O_BITS), };static DEFINE_MUTEX (bq27xxx_list_lock);
drivers/power/supply/bq27xxx_battery_i2c.c +2 -0
@@ -254,6 +254,7 @@ static const struct i2c_device_id bq27xxx_i2c_id_table[] = { { "bq27441", BQ27441 }, { "bq27621", BQ27621 }, { "bq27561", BQ27561 }, + { "bq28z610", BQ28Z610 }, {}, };MODULE_DEVICE_TABLE (i2c, bq27xxx_i2c_id_table);
@@ -288,6 +289,7 @@ static const struct of_device_id bq27xxx_battery_i2c_of_match_table[] = { { .compatible = "ti,bq27441" }, { .compatible = "ti,bq27621" }, { .compatible = "ti,bq27561" }, + { .compatible = "ti,bq28z610" }, {}, };MODULE_DEVICE_TABLE (of, bq27xxx_battery_i2c_of_match_table);
include/linux/power/bq27xxx_battery.h +1 -0
@@ -31,6 +31,7 @@ enum bq27xxx_chip {BQ27441 ,BQ27621 ,BQ27561 , + BQ28Z610, };struct bq27xxx_device_info ;
Signature · 1 line
2.26.2
Quoted 8 lines · Dan Murphy
Add the Texas Instruments bq27561 battery monitor to the bq27xxx binding.
Signed-off-by Dan Murphy <[email protected]>--- Documentation/devicetree/bindings/power/supply/bq27xxx.yaml | 1 + 1 file changed, 1 insertion(+)
Bump to the series
Quoted 20 lines · Dan Murphy
Add the Texas Instruments bq27561 battery monitor to the bq27xxx binding.
Signed-off-by Dan Murphy <[email protected]>--- Documentation/devicetree/bindings/power/supply/bq27xxx.yaml | 1 + 1 file changed, 1 insertion(+)Documentation/devicetree/bindings/power/supply/bq27xxx.yaml +1
-0@@ -49,6 +49,7 @@ properties: - ti,bq27426 - ti,bq27441 - ti,bq27621 + - ti,bq27561 reg: maxItems: 1
Sebastian
Quoted 2 lines · Dan Murphy
Bump to the series
I am wondering if this patchset was applied yet?
I have not recieved any comments except Rob's acks on the bindings
Dan