Skip to contentSkip to conversation

dt-bindings: iio: magnetometer: ak8975: convert format to yaml, add maintainer

PATCH Applied Jonathan Albrieux 2 participants 2 messages May 28, 2020 – May 29, 2020

Subsystems (2)
lore
Share & tools
lore
#0 lore raw

PATCH v7 2/5 dt-bindings: iio: magnetometer: ak8975: convert format to yaml, add maintainer

Converts documentation from txt format to yaml.

---
 .../bindings/iio/magnetometer/ak8975.txt      | 37 ---------
 .../iio/magnetometer/asahi-kasei,ak8975.yaml  | 77 +++++++++++++++++++
 2 files changed, 77 insertions(+), 37 deletions(-)
 delete mode 100644 Documentation/devicetree/bindings/iio/magnetometer/ak8975.txt
 create mode 100644 Documentation/devicetree/bindings/iio/magnetometer/asahi-kasei,ak8975.yaml
Documentation/devicetree/bindings/iio/magnetometer/ak8975.txt deleted +0 -37
deleted file mode 100644
index 0576b9df0bf2..000000000000
@@ -1,37 +0,0 @@
-* AsahiKASEI AK8975 magnetometer sensor
-
-Required properties:
-
-  - compatible : should be "asahi-kasei,ak8975".
-  - reg : the I2C address of the magnetometer.
-
-Optional properties:
-
-  - gpios : AK8975 has a "Data ready" pin (DRDY) which informs that data
-      is ready to be read and is possible to listen on it. If used,
-      this should be active high. Prefer interrupt over this.
-
-  - interrupts : interrupt for DRDY pin. Triggered on rising edge.
-
-  - vdd-supply: an optional regulator that needs to be on to provide VDD.
-
-  - mount-matrix: an optional 3x3 mounting rotation matrix.
-
-Example:
-
-ak8975@c {
-        compatible = "asahi-kasei,ak8975";
-        reg = <0x0c>;
-        interrupt-parent = <&gpio6>;
-        interrupts = <15 IRQ_TYPE_EDGE_RISING>;
-        vdd-supply = <&ldo_3v3_gnss>;
-        mount-matrix = "-0.984807753012208",  /* x0 */
-                       "0",                   /* y0 */
-                       "-0.173648177666930",  /* z0 */
-                       "0",                   /* x1 */
-                       "-1",                  /* y1 */
-                       "0",                   /* z1 */
-                       "-0.173648177666930",  /* x2 */
-                       "0",                   /* y2 */
-                       "0.984807753012208";   /* z2 */
-};
Documentation/devicetree/bindings/iio/magnetometer/asahi-kasei,ak8975.yaml new file +77 -0

77 lines not on this page · raw message

Signature · 1 line
2.17.1
maintainer Reviewed-by on v7 2/5
#1 lore raw
Quoted 91 lines · Jonathan Albrieux

Converts documentation from txt format to yaml.

---
 .../bindings/iio/magnetometer/ak8975.txt      | 37 ---------
 .../iio/magnetometer/asahi-kasei,ak8975.yaml  | 77 +++++++++++++++++++
 2 files changed, 77 insertions(+), 37 deletions(-)
 delete mode 100644 Documentation/devicetree/bindings/iio/magnetometer/ak8975.txt
 create mode 100644 Documentation/devicetree/bindings/iio/magnetometer/asahi-kasei,ak8975.yaml
Documentation/devicetree/bindings/iio/magnetometer/ak8975.txt deleted +0 -37
deleted file mode 100644
index 0576b9df0bf2..000000000000
@@ -1,37 +0,0 @@
-* AsahiKASEI AK8975 magnetometer sensor
-
-Required properties:
-
-  - compatible : should be "asahi-kasei,ak8975".
-  - reg : the I2C address of the magnetometer.
-
-Optional properties:
-
-  - gpios : AK8975 has a "Data ready" pin (DRDY) which informs that data
-      is ready to be read and is possible to listen on it. If used,
-      this should be active high. Prefer interrupt over this.
-
-  - interrupts : interrupt for DRDY pin. Triggered on rising edge.
-
-  - vdd-supply: an optional regulator that needs to be on to provide VDD.
-
-  - mount-matrix: an optional 3x3 mounting rotation matrix.
-
-Example:
-
-ak8975@c {
-        compatible = "asahi-kasei,ak8975";
-        reg = <0x0c>;
-        interrupt-parent = <&gpio6>;
-        interrupts = <15 IRQ_TYPE_EDGE_RISING>;
-        vdd-supply = <&ldo_3v3_gnss>;
-        mount-matrix = "-0.984807753012208",  /* x0 */
-                       "0",                   /* y0 */
-                       "-0.173648177666930",  /* z0 */
-                       "0",                   /* x1 */
-                       "-1",                  /* y1 */
-                       "0",                   /* z1 */
-                       "-0.173648177666930",  /* x2 */
-                       "0",                   /* y2 */
-                       "0.984807753012208";   /* z2 */
-};
Documentation/devicetree/bindings/iio/magnetometer/asahi-kasei,ak8975.yaml new file +32 -0
new file mode 100644
index 000000000000..55b18784e503
@@ -0,0 +1,77 @@
+# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/iio/magnetometer/asahi-kasei,ak8975.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: AsahiKASEI AK8975 magnetometer sensor
+
+maintainers:
+  - Jonathan Albrieux <[email protected]>
+
+properties:
+  compatible:
+    oneOf:
+      - enum:
+        - asahi-kasei,ak8975
+        - asahi-kasei,ak8963
+        - asahi-kasei,ak09911
+        - asahi-kasei,ak09912
+      - enum:
+        - ak8975
+        - ak8963
+        - ak09911
+        - ak09912
+        deprecated: true
+
+  reg:
+    maxItems: 1
+
+  gpios:
+    maxItems: 1
+    description: |

Documentation/devicetree/bindings/iio/magnetometer/asahi-kasei,ak8975.yaml line 42

Quoted 10 lines
Documentation/devicetree/bindings/iio/magnetometer/asahi-kasei,ak8975.yaml new file +10 -0
+      AK8975 has a "Data ready" pin (DRDY) which informs that data
+      is ready to be read and is possible to listen on it. If used,
+      this should be active high. Prefer interrupt over this.
+
+  interrupts:
+    maxItems: 1
+    description: interrupt for DRDY pin. Triggered on rising edge.
+
+  vdd-supply:
+    maxItems: 1

Drop this. -supply is always 1.

With that,