dt-bindings: iio: magnetometer: ak8975: add gpio reset support
Subsystems (2)
PATCH v7 3/5 dt-bindings: iio: magnetometer: ak8975: add gpio reset support
Add reset-gpio support.
Without reset's deassertion during ak8975_power_on(), driver's probe fails on ak8975_who_i_am() while checking for device identity for AK09911 chip.
AK09911 has an active low reset gpio to handle register's reset. AK09911 datasheet says that, if not used, reset pin should be connected to VID. This patch emulates this situation.
--- .../bindings/iio/magnetometer/asahi-kasei,ak8975.yaml | 7 +++++++ 1 file changed, 7 insertions(+)
Documentation/devicetree/bindings/iio/magnetometer/asahi-kasei,ak8975.yaml +7 -0
@@ -47,6 +47,11 @@ properties: mount-matrix: description: an optional 3x3 mounting rotation matrix. + reset-gpios: + description: | + an optional pin needed for AK09911 to set the reset state. This should + be usually active low + required: - compatible - reg
@@ -54,6 +59,7 @@ required: examples: - | #include <dt-bindings/interrupt-controller/irq.h> + #include <dt-bindings/gpio/gpio.h> i2c { #address-cells = <1>; #size-cells = <0>;
@@ -64,6 +70,7 @@ examples: interrupt-parent = <&gpio6>; interrupts = <15 IRQ_TYPE_EDGE_RISING>; vdd-supply = <&ldo_3v3_gnss>; + reset-gpios = <&msmgpio 111 GPIO_ACTIVE_LOW>; mount-matrix = "-0.984807753012208", /* x0 */ "0", /* y0 */ "-0.173648177666930", /* z0 */
Signature · 1 line
2.17.1
Jonathan Cameron
maintainerQuoted 11 lines · On Thu, 28 May 2020 16:59:28 +0200 Jonathan Albrieux…
Add reset-gpio support.
Without reset's deassertion during
ak8975_power_on(), driver's probe fails onak8975_who_i_am()while checking for device identity for AK09911 chip.AK09911 has an active low reset gpio to handle register's reset. AK09911 datasheet says that, if not used, reset pin should be connected to VID. This patch emulates this situation.
Signed-off-by Jonathan Albrieux <[email protected]>Reviewed-by Rob Herring <[email protected]>
Applied to the togreg branch of iio.git and pushed out as testing for the autobuilders to play with it.
thanks,
Jonathan
Quoted 36 lines
--- .../bindings/iio/magnetometer/asahi-kasei,ak8975.yaml | 7 +++++++ 1 file changed, 7 insertions(+)Documentation/devicetree/bindings/iio/magnetometer/asahi-kasei,ak8975.yaml +7
-0@@ -47,6 +47,11 @@ properties: mount-matrix: description: an optional 3x3 mounting rotation matrix. + reset-gpios: + description: | + an optional pin needed for AK09911 to set the reset state. This should + be usually active low + required: - compatible - reg@@ -54,6 +59,7 @@ required: examples: - | #include <dt-bindings/interrupt-controller/irq.h> + #include <dt-bindings/gpio/gpio.h> i2c { #address-cells = <1>; #size-cells = <0>;@@ -64,6 +70,7 @@ examples: interrupt-parent = <&gpio6>; interrupts = <15 IRQ_TYPE_EDGE_RISING>; vdd-supply = <&ldo_3v3_gnss>; + reset-gpios = <&msmgpio 111 GPIO_ACTIVE_LOW>; mount-matrix = "-0.984807753012208", /* x0 */ "0", /* y0 */ "-0.173648177666930", /* z0 */